Troubleshooting guide | American Standard 2808.222 Indoor Furnishings User Manual

Installation
Instructions
TM
2808.222
2908.222
W idespread Lavatory Faucet with the
Speed Connect™ Drain
Congratulations on purchasing your American Standard faucet with
the Speed Connect Drain, a feature found only on
American Standard faucets.
Certified to comply with ANSI A112.18.1
Speed Connect Drain*
U S 6 0 3 8 5 R e v. 1 . 2
• 1/3 of the parts, installs in 1/3 of the time
• No tools needed
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
*Your new American Standard faucet is designed to work only with the Speed Connect drain. Helpful tips for
removing your current drain can be found in the Troubleshooting section of these instructions.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Recommended tools
Screwdriver
1
INSTALL SPOUT
Channel Locks
CAUTION
Tubing Cutter
Adjustable Wrench
Turn off water at
main supply.
Fig.
Insert SPOUT (1) and CABLE CONNECTOR (2) through center hole, making sure
the SEAL WASHER (3) is properly seated in SPOUT (1).
Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto SPOUT
SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting
hole and the slot in the BRASS WASHER (5) faces toward the rear of the sink.
A.
1
Tighten LOCKNUT (6) firmly. Fig. A.
3
1A
7
INSTALL VALVE BODY
Place RUBBER RING (9) into ESCUTCHEON (10).
4
Install LOCKNUT (11) onto VALVE BODY (12).
From under side of mounting surface, install VALVE BODY (12) through valve
mounting holes. Threads of VALVE BODY (12) should extent at least 5/16
of a inch above mounting surface top. Fig. B.
5
SLOT
6
Important: Thread ESCUTCHEON (10) onto VALVE BODY (12) until snug against
internal stop. This is key to the installation. If not done, the faucet handles won’t
work correctly. If necessary, adjust LOCKNUT (11).
2
Hand tighten LOCKNUT (11) to secure VALVE BODY (12).
Repeat above steps for opposite VALVE BODY (12A).
10
9
10
5/16'' MIN.
MOUNTING
SURFACE
Fig. B.
11
12
1
9
12a
12
2808 SERIES
11
1
2
INSTALL POP-UP DRAIN
Fig. A.
Remove CLEAR PLASTIC COVER (1).
Remove CARDBOARD SPACER (2) from
under DRAIN POP-UP (3). Fig. A.
REAR OF
SINK
1
4
3
Drop DRAIN BODY (4) through sink drain
hole. Make sure WHITE FOAM GASKET (5)
is under flange of DRAIN BODY (4). Fig. B.
Note: No plumber’s putty or caulk is required.
Fig. B.
6
5
SINK
DRAIN
HOLE
2
The CABLE ATTACHMENT POINT (6) must
face towards the rear of the SINK. Fig. B.
3
INSTALL BLACK GASKET
Install BLACK CONE GASKET (1) onto DRAIN BODY (2)
from below.
Note: The flat side of the BLACK CONE GASKET (1) must
face down.
2
1
FLAT SIDE OF GASKET
MUST FACE DOWN
4
INSTALL GRAY LOCKNUT
Fig. B.
Fig. A.
Install GRAY LOCKNUT (1) onto DRAIN
BODY (2) from below SINK. Fig. A.
Note: The flat side of the GRAY LOCKNUT (1)
must face up.
2
Tighten firmly by hand. No tools are required.
Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET (3) is fully compressed
and not visible. Fig. B.
DRAIN
FLANGE
FLAT SIDE OF
GRAY LOCKNUT
MUST FACE UP
1
5
POP-UP KNOB
3
WHITE FOAM
GASKET
NOT VISIBLE
DOWN
POP-UP KNOB (1) must be fully down.
1
U S 6 0 3 8 5 R e v. 1 . 2
2
6
ATTACH CABLE CONNECTOR
Fig. A.
Fig. B.
Thread CABLE CONNECTOR (1) clockwise
onto DRAIN BODY CONNECTION (2) and
hand tighten. Fig. A.
1
Your new POP-UP DRAIN installation is
now complete. Fig. B.
Note: Tailpeice on pop-up drain is 1-1/4” O.D.
Fig. B.
1-1/4” O.D.
2
7
CHECK OPERATION OF POP-UP
Operate LIFT KNOB (1) to verify that STOPPER (2) opens and
closes.
1
Note: If STOPPER (2) does not open and close properly then
refer to the “troubleshooting section” of these instructions.
2
8
MAKE WATER SUPPLY AND WASTE CONNECTIONS
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED
AND MUST BE PURCHASED SEPARATELY.
Thread TEE BODY (4) to SPOUT SHANK (5).
Thread HOSE CONNECTOR (6, 6A) to VALVE CONNECTIONS (7, 7A).
Connect water supply to VALVE BODIES (1,1A) with 1/2" IPS FLEXIBLE
SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3). Use
adjustable wrench to tighten connections. Do not over
tighten. Be careful not to kink copper supply when bending.
Use tubing cutter to cut to proper length.
Connect HOT water supply to inlet of left SHANK and COLD
water supply to right SHANK using sealant, appropriate
connectors, and COUPLING NUTS.
Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to
waste outlet.
1
1/2" PIPE THREAD
1A
5
6A
7A
COUPLING
NUT
7
4
3/8 O.D.
BULL-NOSE
RISERS
6
WASTE
OUTLET
2
FLEXIBLE
SUPPLIES
3
COMPRESSION
NUT
FERRULE
COLD
HOT
3/8 COMPRESSION
CONNECTION
U S 6 0 3 8 5 R e v. 1 . 2
3
9
6
INSTALL HANDLES
6
Push ADAPTER (1) on VALVE
STEM (2), so that the hole of the
ADAPTER (1) without spline is
facing up.
Insert MOUNTING ROD ASSEMBLY (1) into METAL HANDLE (3)
and HANDLE COLLAR (4).
4
Thread HANDLE ASSEMBLY (6) into ball of HANDLE BASE (5)
and tighten.
TOP
Find correct position of
HANDLE (4) by adjusting
male teeth on ADAPTER (1)
to female teeth in
LEVER BALL (4).
Secure LEVER BALL (4)
with HANDLE SCREW (5).
Push INDEX CAP (6)
in hole of LEVER BALL (4).
Thread PORCELIAN LEVER HANDLE (2) counter-clockwise
and remove INDEX BUTTON with MOUNTING ROD ASSEMBLY (1).
5
Thread HANDLE BASE (3) onto
VALVE ESCUTCHEON (7)
Push LEVER BALL (4) onto
ADAPTER (1).
INSTALLATION OF OPTIONAL METAL LEVER
HANDLES (Supplied with Faucet)
3
2
1
3
2
5
4
1
7
SPLINE END
DOWN
6
10
5
TEST INSTALLED FITTING
1
With HANDLES (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
Remove AERATOR (3).
3
1
Operate both HANDLES (1) to flush water
lines thoroughly.
Replace AERATOR (3).
4
11
CHECK DRAIN CONNECTIONS
Operate POP-UP KNOB (5) and fill Sink with water.
Check that DRAIN STOPPER (4) makes a good seal
and retains water in Sink. If STOPPER (4) does not
seal properly, please refer to “Troubleshooting Guide”
in these instructions.
WASTE
OUTLET
2
Release POP-UP KNOB (5) down and check all
drain connections and "P" trap for leaks.
Tighten if necessary.
COLD
“P” TRAP
HOT
12
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT
CLEAN WITH CLEAR WATER.
DRY WITH A SOFT COTTON
FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE
PRODUCT WITH SOAPS, ACID,
POLISH, ABRASIVES, HARSH
CLEANERS, OR A CLOTH WITH
A COARSE SURFACE.
13
2
SERVICE
To change direction of handle rotation, proceed as follows:
Turn valve to OFF position.
Remove INSERT and HANDLE SCREW.
Slip HANDLE with ADAPTER off.
Remove SPRING CLIP (1).
Lift STOP WASHER (2), turn 90 and replace.
Replace SPRING CLIP (1).
Replace ADAPTER, HANDLE, SCREW, and INSERT.
Spray may accumulate dirt causing distorted and reduced
water flow. Remove spray and rinse clean.
2
90
1
Replace Spray and operate handles several times from
OFF to ON position. Do not force, handles turn only 90˚.
U S 6 0 3 8 5 R e v. 1 . 2
4
Download PDF

advertising