COLONY/COLONY SOFT

Installation

Instructions

Bidet Faucet and Transfer Valve

3475.301

3475.501

with SpeedConnect™ Drain

Congratulations on purchasing your American

Standard faucet with Speed Connect drain, a feature found only on American Standard faucets.

SpeedConnect Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the first time, every time.

Certified to comply with ANSI A112.18.1

M 9 6 8 7 9 6 R e v. 1 . 1

*Your new American Standard faucet is designed to work only with the SpeedConnect drain.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Roughing-in Dimensions

TRANSFER VALVE

(FOR FLUSHING

RIM OR SPRAY)

FINISHED

WALL

BIDET OUTLINE

IS SYMBOLIC 7/8 DIA.

Required tools

(C)

8 TO 12

(H)

DIVERTER AND

VACUUM BREAKER

ASSEMBLY

2-1/4

DIA.

Screwdriver

DOUCHE

SPRAY

ADJ. 1-1/4

TO 2-1/4

2-1/8

DIA.

1-3/16 DIA.

1-1/4 MAX.

4-1/4

Phillips Screwdriver

3-7/8

1-3/8

DIA.

FOR GROUND JOINT

CONNECTION OR 1/2 "

O.D. SLIP (INLETS)

FINISHED

FLOOR

REAR VIEW WITH

WALL REMOVED

5-1/2

1-1/4 O.D. TAILPIECE

1

BIDET FAUCET INSTALLATION

CAUTION

Place RUBBER RING (10) into ADAPTER (4).

Turn off hot and cold water supplies before beginning.

Install LOCKNUT (1) and RUBBER WASHER (2) onto VALVE BODIES (3, 3a). From under side of mounting surface, install VALVE BODY (3, 3a) through valve mounting holes. Threads of VALVE BODY (3, 3a) should extent at least 5/16 of a inch above mounting surface top. Fig. A. Thread ADAPTER (4) onto VALVE BODIES (3, 3a) until snug against internal stop. If necessary, adjust LOCKNUT (1).

Tighten LOCKNUTS (1) with WRENCH (5) (supplied) to secure VALVE BODIES (3, 3a).

Remove MOUNTING NUT (6), WASHER (7) and

UPPER GASKET (8) from TRANSFER VALVE (9).

Insert TRANSFER VALVE (9) into the center forward hole of BIDET.

Replace UPPER GASKET (8) and WASHER (7) . Position the side threaded outlet rearward and secure MOUNTING

NUT (6). Thread ESCUTCHEON (11) onto TRANSFER

VALVE (9) until it seats against the BIDET LEDGE.

Fig. A.

5/16''

MIN.

3, 3a

2 8

SPRAY INSTALLATION

Assemble SPRAY BODY (1) to BIDET. Using putty, seal underside of SPRAY BODY FLANGE (2) and secure with NUT (3).

Thread SPRAY HOSE (4) with SEAL WASHER (5) to SPRAY BODY (1).

Connect other end of HOSE (4) with SEAL WASHER (6) to side outlet

NIPPLE (7) of the TRANSFER VALVE (8).

Thread SPRAY CAP (9) onto SPRAY BODY (1).

7

6

Adjustable Wrench

4

10

4

10

MOUNTING

SURFACE

2

2

1

1

5

4

11

HOT

3

2

PUTTY

3

Plumbers' Putty or

Caulking

Channel Locks

Tubing Cutter

6

7

9

8

COLD

3a

9

1

5

4

BIDET

LEDGE

1

3

POP-UP DRAIN

Remove CLEAR PLASTIC COVER (1).

Remove CARDBOARD SPACER (2) from under

DRAIN POP-UP (3).

Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B.

Fig. A.

1

3

2

4

REMOVE FLANGE

Thread FLANGE (1) counter-clockwise and remove

FLANGE (1) and FOAM GASKET (2) from drain body.

Fig. A.

Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against

LOCKNUT (3). Fig. B.

Fig. A.

1

2

4

3

Fig. B.

Fig. B.

DRAIN

BODY

7

5 INSTALL DRAIN FROM

BELOW FIXTURE

From under side of BIDET install DRAIN BODY (1) up through drain outlet.

Note: No plumber’s putty or caulk is required.

The CABLE ATTACHMENT

POINT (2) must face towards the rear of the BIDET.

Install FOAM GASKET (3) and

FLANGE (4) onto drain body from above BIDET and tighten

FLANGE (4) firmly.

4

3

DRAIN

OUTLET

1

2

6

TIGHTEN LOCKNUT

Tighten LOCKNUT (1) firmly with Adjustable

Wrench or Channel Locks.

7

FLANGE GASKET

Check DRAIN FLANGE in BIDET to ensure that WHITE

FOAM GASKET (1) is fully compressed and not visible.

Fig. A.

POP-UP ROD ASSEMBLY

Insert LIFT ROD GUIDE (1) and CABLE CONNECTOR (2) through rear hole, making sure SEAL WASHER (3) is properly seated. Fig. B.

From below slip slot in MOUNTING NUT (4) over CABLE (5).

Thread NUT (4) onto lift rod guide shank to secure ROD

GUIDE (1) to bidet. Hand tighten only. Fig. B.

Fig. A.

DRAIN

FLANGE

1

WHITE FOAM

GASKET

NOT VISIBLE

2

1

Fig. B.

3

1

5

ILLUSTRATION

SHOWN LESS

VALVES

SLOTTED

MOUNTING

NUT

4

2

M 9 6 8 7 9 6 R e v. 1 . 1

8 ATTACH CABLE

CONNECTOR

POP-UP KNOB (1) must be fully down. Fig. A.

Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY

CONNECTION (2) and hand tighten. Fig. B.

Your new POP-UP DRAIN installation is now complete.

Fig. C.

Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. C.

Fig. A.

DOWN

9

CHECK OPERATION OF POP-UP

Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes.

Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.

INSTALL DIVERTER KNOB

Push DIVERTER KNOB (1) onto HANDLE ADAPTER (2).

Push on RING (3) and tighten with SCREW (4).

Press on KNOB CAP (5).

Note: Screwdriver gap is for disassembling and should point downwards.

2

Fig. B.

10

TEE AND HOSE CONNECTION

Insert SEAL (1) into ADAPTER (2) and tighten ADAPTER (2) to bottom of TRANSFER VALVE (3).

Install SEAL (4) into coupling nut of TEE (5) and tighten connection to ADAPTER (2).

Connect HOSE COUPLING NUTS (6) to Hot and Cold valve bodies and securely tighten.

2

WATER SUPPLY CONNECTION

7

NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT

INCLUDED AND MUST BE PURCHASED SEPARATELY.

Connect water supply to VALVE BODIES (7,7a) with

1/2" IPS FLEXIBLE SUPPLIES (2) or 3/8" O.D. BULL-NOSE

RISERS (3). Use adjustable wrench to tighten connections.

Do not over tighten. Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length.

1/2" PIPE

THREAD

2

FLEXIBLE

SUPPLIES

Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant, appropriate connectors, and COUPLING NUTS.

Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet.

HOT

6

1

5

1

1

Fig. C.

3

4

2

6

1-1/4” O.D.

3

1

5

4

2

7a

Front

COUPLING

NUT

3

3/8 O.D.

BULL-NOSE

RISERS

COMPRESSION

NUT

FERRULE

COLD

CONNECT TO

WASTE OUTLET

3/8 COMPRESSION

CONNECTION

M 9 6 8 7 9 6 R e v. 1 . 1

3

11

INSTALL HANDLES (Lever)

Turn HANDLE STEM (1) to "OFF" position.

Place the HANDLE ADAPTER (2) on the HANDLE STEM (1).

Install the ADAPTER SCREW (3) and tighten securely. Position

LEVER HANDLE (4) and place on ADAPTER (2).

Install the HANDLE SCREW (5) and tighten securely with hex wrench supplied.

5

4

3

2

1

12

TEST INSTALLED FITTING

With HANDLES (1) in OFF position, turn on WATER

SUPPLIES (2) and check all connections for leaks.

Operate both HANDLES (1) to flush water lines thoroughly.

Rotate TRANSFER VALVE (5) from rim wash to spray several times to check operation.

1

INSTALL HANDLES (Acrylic)

Turn HANDLE STEM (1) to "OFF" position.

Place the ACRYLIC HANDLE (2) on the HANDLE STEM (1).

Install the HANDLE SCREW (3) and tighten securely.

Push in INDEX BUTTON (4).

2

4

3

1

3

5

H

1

13

CHECK DRAIN CONNECTIONS

Pull up POP-UP KNOB (3) and fill Bidet with water. Check that DRAIN STOPPER (4) makes a good seal and retains water in Bidet. If STOPPER (4) does not seal properly, please refer to “Troubleshooting Guide” in these instructions.

Push POP-UP KNOB (3) down and check all drain connections and "P" trap for leaks. Tighten if necessary.

2

4

2

SPRAY

14

EverClean™ Finish

Care Instructions

American Standard’s EverClean finish will wipe clean with a soft, dry cloth.

A soft cloth with clean water may also be used, if desired.

No additional cleaning products are required.

DO NOT USE: Soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface.

15 SERVICE

To change direction of handle rotation, proceed as follows:

Turn VALVE to OFF position.

Loosen HANDLE SCREW (1) .

Pull HANDLE (2) off ADAPTER (3). Loosen ADAPTER

SCREW (4) and pull off ADAPTER (3).

Turn ADAPTER (3) 90˚ in a way that flat in ADAPTER (3) catches on the other FLAT on VALVE STEM (5).

Reinstall ADAPTER SCREW (4) and LEVER HANDLE (2).

Tighten HANDLE SCREW (1).

If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90˚.

1

2

4

3

5

M 9 6 8 7 9 6 R e v. 1 . 1

4

SpeedConnect™ Drain

Troubleshooting Guide

If sink does not hold water even though Stopper is in the “down” position:

• Follow CABLE ADJUSTMENT PROCEDURE.

If Stopper does not raise up fully or sink drains too slowly:

• Follow CABLE ADJUSTMENT PROCEDURE.

If you need to remove the Stopper:

• Follow STOPPER REMOVAL PROCEDURE.

If you would like the ability to remove your Stopper simply by lifting it out of the drain:

• Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.

CABLE ADJUSTMENT PROCEDURE

Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.

Look at the area on the Drain Body where the Cable was attached and locate the component labeled as

“Cam” in the illustration. Fig. B.

Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the

Stopper should be in the UP position. Fig. B, C.

Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.

Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the

Drain Body Connection (2) and hand-tighten. Fig. A.

Fig. A.

Fig. B.

Fig. C.

DOWN

CAM 1

RE-ATTACH

1

CAM CAP

STOPPER

DISCONNECT

2

STOPPER REMOVAL PROCEDURE

Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.

Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the illustration. Fig. B.

Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.

Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.

The Stopper can now be removed by lifting it out of the Drain. Fig. F.

Fig. D.

Fig. E.

REMOVE

CAM

Fig. F.

REMOVE

CAM CAP

M 9 6 8 7 9 6 R e v. 1 . 1

5

STOPPER INSTALLATION PROCEDURE

The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable).

Locked Mode:

Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G.

To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the

Sink and the American Standard logo is facing front. Rotate

Stopper slightly if necessary so that the Stopper slides all the way down.Fig. G.

Re-install the Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted. Fig. J.

Re-install the Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not “snap” into place, then rotate the Cam to make sure it is fully inserted. Fig. K.

Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in

Troubling Shooting Guide to complete installation. Stopper will be in “Locked” mode and not be removable.

LOGO

Fig. G.

LOOP TOWARD

REAR OF BIDET

DRAIN

Locked Mode

(Vandal Proof)

Unlocked Mode:

Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. H.

To install the stopper in “Unlocked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the

Sink and the American Standard logo is facing rear. Rotate Stopper slightly if necessary so that the Stopper slides all the way down.

Fig. H.

Re-install the Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted. Fig. J.

Re-install the Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not “snap” into place, then rotate the Cam to make sure it is fully inserted. Fig. K.

Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in

“Troublingshooting Guide” to complete installation. Stopper will be in “Unlocked” mode and removable .

LOGO

Fig. H.

180˚

LOOP TOWARD

FRONT OF BIDET

DRAIN

Unlocked Mode

Fig. J.

INSTALL CAM

CAM

Fig. K.

INSTALL

CAM CAP

M 9 6 8 7 9 6 R e v. 1 . 1

6