American Standard 3698.016 Indoor Furnishings User Manual

Installation
Instructions
AMARILIS
3801.000
3841.000
Spread Lavatory Faucet with
Speed Connect™ Drain
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
Speed Connect™ Drain*
Certified to comply with ANSI A112.18.1
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
4 3 1 6 7 R e v. 1 . 3
*Your new American Standard faucet is designed to work only with the Speed Connect drain. Heplful tips for
removing your current drain can be found in the Troubleshooting section of these instructions.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Recommended tools
Screwdriver
1
INSTALL SPOUT
Channel Locks
CAUTION
Adjustable Wrench
Tubing Cutter
Turn off hot and cold water
supplies before beginning.
JASMINE
SPOUT
Fig. A.
Insert SPOUT (1) and CABLE CONNECTOR (14) through center hole, making sure
the SPOUT ESCUTCHEON (2) and SEAL WASHER (3) are properly seated.
Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto SPOUT
SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting
hole and the slot in the BRASS WASHER (5) faces toward the rear of the sink.
1
2
3
7
Tighten LOCKNUT (6) firmly. Fig. A.
1A
INSTALL VALVE BODY
Place RUBBER RING (9) into DECK ADAPTER (10).
Install LOCKNUT (11) and RUBBER WASHER (12) onto VALVE BODY (13).
From under side of mounting surface, install VALVE BODY (13) through valve
mounting holes. Threads of VALVE BODY (13) should extent at least 5/16
of a inch above mounting surface top. Fig. B. Thread DECK ADAPTER (10)
onto VALVE BODY (13) until snug against internal stop. If necessary, adjust
LOCKNUT (11).
Tighten LOCKNUT (11) with WRENCH (8) (supplied) to secure VALVE
BODY (13). Repeat above steps for opposite VALVE BODY (13A).
10
9
5/16'' MIN.
4
SLOT
5
6
1
14
10
MOUNTING
SURFACE
9
13a
12
Fig. B.
12
11
11
13
13
IRIS
SPOUT
8
1
2
POP-UP DRAIN
Fig. A.
Remove CLEAR PLASTIC COVER (1).
Fig. B.
1
Remove CARDBOARD SPACER (2) from under
DRAIN POP-UP (3).
DRAIN
BODY
3
Tighten TAILPIECE (4) on DRAIN BODY before
installing DRAIN BODY. Fig. B.
2
3
REMOVE FLANGE
4
Fig. A.
Thread FLANGE (1) counter-clockwise and remove
FLANGE (1) and FOAM GASKET (2) from drain
body. Fig. A.
Fig. B.
1
Thread LOCKNUT (3) clock-wise to bottom of
drain body. Push GASKET (4) down against
LOCKNUT (3). Fig. B.
4
2
3
4
INSTALL DRAIN FROM
BELOW FIXTURE
From under side of SINK
install DRAIN BODY (1) up
through drain outlet.
Note: No plumber’s putty
or caulk is required.
The CABLE ATTACHMENT
POINT (2) must face towards
the rear of the SINK.
REAR OF SINK
TIGHTEN LOCKNUT
Tighten LOCKNUT (1) firmly with Adjustable
Wrench or Channel Locks.
4
DRAIN
OUTLET
3
1
Install FOAM GASKET (3) and
FLANGE (4) onto drain body
from above SINK and tighten
FLANGE (4) firmly.
6
5
FLANGE GASKET AND POP-UP KNOB
1
2
Fig. A.
Fig. B.
DOWN
Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET (3) is fully compressed
and not visible. Fig. A.
POP-UP KNOB (1) must be fully down. Fig. B.
1
WHITE FOAM
GASKET
NOT VISIBLE
DRAIN
FLANGE
4 3 1 6 7 R e v. 1 . 3
2
7
ATTACH CABLE CONNECTOR
Fig. A.
Fig. B.
Thread CABLE CONNECTOR (1) clockwise
onto DRAIN BODY CONNECTION (2) and
hand tighten. Fig. A.
1
Your new POP-UP DRAIN installation is
now complete. Fig. B.
Note: Tailpeice on pop-up drain is 1-1/4” O.D.
Fig. B.
2
1-1/4” O.D.
8
CHECK OPERATION OF POP-UP
Operate LIFT KNOB (1) to verify that STOPPER (2) opens and
closes.
1
Note: If STOPPER (2) does not open and close properly then refer
to the “troubleshooting section” of these instructions.
2
9
MAKE WATER SUPPLY AND WASTE CONNECTIONS
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED
AND MUST BE PURCHASED SEPARATELY.
Thread TEE BODY (4) to SPOUT SHANK (5).
Thread HOSE CONNECTOR (6, 6A) to VALVE CONNECTIONS (7, 7A).
Connect water supply to VALVE BODIES (1,1A) with 1/2" IPS FLEXIBLE
SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3). Use
adjustable wrench to tighten connections. Do not over tighten.
Be careful not to kink copper supply when bending. Use tubing
cutter to cut to proper length.
Connect HOT water supply to inlet of left SHANK and COLD
water supply to right SHANK using sealant, appropriate
connectors, and COUPLING NUTS.
Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to
waste outlet.
1
1/2" PIPE THREAD
1A
5
7A
COUPLING
NUT
7
4
6
3/8 O.D.
BULL-NOSE
RISERS
2
FLEXIBLE
SUPPLIES
HOT
6A
COLD
3
COMPRESSION
NUT
FERRULE
3/8 COMPRESSION
CONNECTION
4 3 1 6 7 R e v. 1 . 3
3
10
INSTALL HANDLES
See separate installation instructions supplied with handle kits for installing handles onto fitting.
11
TEST INSTALLED FITTING
With HANDLES (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
5
Remove AERATOR (3).
1
Operate both HANDLES (1) to flush water
lines thoroughly.
Replace AERATOR (3).
1
3
12
4
CHECK DRAIN CONNECTIONS
Operate POP-UP KNOB (5) and fill Sink with water. Check
that DRAIN STOPPER (4) makes a good seal and retains
water in Sink. If STOPPER (4) does not seal properly, please
refer to “Troubleshooting Guide” in these instructions.
WASTE
OUTLET
2
Release POP-UP KNOB (5) down and check all drain
connections and "P" trap for leaks.
Tighten
if necessary.
COLD
HOT
TO CLEAN AERATOR
“P” TRAP
AERATOR (3) may accumulate dirt causing distorted
and reduced water flow. Unscrew and remove
AERATOR (3) and rinse clean.
2
Replace AERATOR (3) and operate handles several times
from OFF to ON position. Do not force, handles turn only 90˚.
13
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT
CLEAN WITH CLEAR WATER. DRY
WITH A SOFT COTTON FLANNEL
CLOTH.
DO NOT: DO NOT CLEAN THE
PRODUCT WITH SOAPS, ACID,
POLISH, ABRASIVES, HARSH
CLEANERS, OR A CLOTH WITH
A COARSE SURFACE.
14
HANDLE
ASSEMBLY
SERVICE
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position. See handle instructions
with handle kit for removing handles.
Remove ADAPTER SCREW (1) and pull of ADAPTER (2).
1
Remove SPRING CLIP (3). Lift STOP WASHER (4),
turn 90° and replace. Replace SPRING CLIP (3).
2
Replace handle assembly. See handle instructions
with handle kit for installing handles.
4
90˚
3
4 3 1 6 7 R e v. 1 . 3
4
Speed Connect™ Drain
Troubleshooting Guide
If sink does not hold water even though Stopper is in the “down” position:
• Follow CABLE ADJUSTMENT PROCEDURE.
If Stopper does not raise up fully or sink drains too slowly:
• Follow CABLE ADJUSTMENT PROCEDURE.
If you need to remove the Stopper:
• Follow STOPPER REMOVAL PROCEDURE.
If you would like the ability to remove your Stopper simply by lifting it out of the drain:
• Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
CABLE ADJUSTMENT PROCEDURE
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
Look at the area on the Drain Body where the Cable was attached and locate the component labeled as
“Cam” in the illustration. Fig. B.
Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the
Stopper should be in the UP position. Fig. B, C.
Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.
Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the
Drain Body Connection (2) and hand-tighten. Fig. A.
Fig. A.
Fig. B. Fig. C.
DOWN
CAM
1
1
RE-ATTACH
CAM CAP
STOPPER
DISCONNECT
2
STOPPER REMOVAL PROCEDURE
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
Look at the area on the Drain Body where the Cable was attached and locate the component labeled
as “Cam” and “Cam Cap” in the illustration. Fig. B.
Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.
Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.
The Stopper can now be removed by lifting it out of the Drain. Fig. F.
Fig. D.
Fig. E.
REMOVE
CAM
Fig. F.
REMOVE
CAM CAP
4 3 1 6 7 R e v. 1 . 3
5
STOPPER INSTALLATION PROCEDURE
The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be
removed) or “Unlock” Mode (Stopper is removable).
Locked Mode:
Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper. Fig. G.
To install the stopper in “Locked” mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the rear of the
Sink and the American Standard logo is facing front. Rotate
Stopper slightly if necessary so that the Stopper slides all the
way down.Fig. G.
Fig. G.
LOGO
Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted. Fig. J.
LOOP TOWARD
REAR OF SINK
Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted. Fig. K.
DRAIN
Locked Mode
(Vandal Proof)
Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
Troubling Shooting Guide to complete installation. Stopper will be
in “Locked” mode and not be removable.
Unlocked Mode:
Fig. H.
Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper. Fig. H.
To install the stopper in “Unlocked” mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the front of the
Sink and the American Standard logo is facing rear. Rotate Stopper
slightly if necessary so that the Stopper slides all the way down.
Fig. H.
LOGO
180˚
Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted. Fig. J.
LOOP TOWARD
FRONT OF SINK
Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted. Fig. K.
DRAIN
Unlocked Mode
Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
“Troublingshooting Guide” to complete installation. Stopper will be
in “Unlocked” mode and removable.
Fig. J.
CAM
INSTALL CAM
Fig. K.
INSTALL
CAM CAP
4 3 1 6 7 R e v. 1 . 3
6
AMARILIS
WIDESPREAD
LAVATORY FAUCET
MODEL NUMBER
M962533-YYY0A
POP-UP ROD
IRIS (3841)
SPOUT
JASMINE (3801)
SPOUT
M962531-YYY0A
POP-UP ROD
M962530-YYY0A
IRIS SPOUT KIT
066124-YYY0A
DECORATIVE RING
066124-YYY0A
DECORATIVE RING
909719-YYY0A
SPOUT
ESCUTCHEON
909718-YYY0A
SPOUT ESCUTCHEON
066070-YYY0A
AERATOR
3801.000
3841.000
066121-YYY0A
SPOUT KIT
030135-YYY0A
SPOUT KIT
066070-YYY0A
AERATOR
911836-0070A
RUBBER RING
M962532-YYY0A
SPOUT KIT
911862-0070A
RUBBER RING
033759-0070A
HOSE SEAL KIT
M961733-0070A
SPOUT
MOUNTING KIT
M961733-0070A
SPOUT
MOUNTING KIT
028610-0070A
CARTRIDGE
033757-0070A
TEE MOUNTING KIT
033758-0050A
TEE & HOSE KIT
SPOUT AND HOSE KITS
BEFORE 12/06
030257-YYY0A
ESCUTCHEON KIT
M962544-YYY0A
STOPPER
ASSEMBLY
030258-0070A
VALVE
MOUNTING KIT
M952425-YYY0A
DRAIN ASSEMBLY
M962457-007A
FLANGE
ASSEMBLY
M953006-0070A
TEE & HOSE KIT
024220-0070A
SUPPLY NUT
066116-YYY0A
DRAIN STOPPER
M922872-0070A
CAM SEAT INSERT
M919660-0020A
6” TAILPIECE
(NOT INCLUDED
WITH FAUCET)
M962430-0070A
CAM ASSEMBLY
M913207-0070A
TAILPIECE INSERT
066117-YYY0A
2" FLANGE KIT
M953450-YYY0A
COMPLETE
DRAIN ASSEMBLY
066118-0070A
PIVOT ROD KIT
066122-YYY0A
LIFT ROD (IRIS)
028618-YYY0A
LIFT ROD (JASMINE)
072574-0070A
EXTENSION ROD
M952430-0070A
CABLE ASSEMBLY
Replace the "YYY" with
appropriate finish code
CHROME
WHITE
BLK. NICKEL/BRASS
BLACK SMITH
POLISHED BRASS
SATIN/CHROME
SATIN NICKEL
SATIN/BRASS
CHROME/BRASS
070847-0070A
CLIP
002
020
062
078
099
221
295
297
299
A919661-0020A
TAILPIECE
M962458-0070A
DRAIN MOUNTING KIT
4 3 1 6 7 R e v. 1 . 3
M961711-0070A
TAILPIECE INSERT
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-12-00
070532-0040A
TAILPIECE
POP-UP DRAIN ASSEMBLY
BEFORE 01/07
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2008
7