American Standard 4508.201 Indoor Furnishings User Manual

Installation
Instructions
4508.201
PRINCETON
Centerset Lavatory Faucet with
Speed Connect™ Drain
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
Speed Connect™ Drain*
Certified to comply with ANSI A112.18.1
M968843 Rev. 1.2
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Required tools
Screwdriver
1
INSTALL FAUCET
Adjustable Wrench
Channel Locks
CAUTION
Tubing Cutter
Turn off water at
main supply.
Fig. A.
Turn off hot and cold water supplies before beginning.
Note: Putty is not required unless mounting surface
is uneven. Apply a bead of PUTTY along the edge of
the underside of the BODY (1) if required.
Insert FAUCET (1) and CABLE CONNECTOR (2) through
mounting holes of Sink or mounting surface. Fig. A.
Assemble LOCKNUTS (3) onto SHANKS (4) from under
side of Sink. Hand tighten firmly. Fig. B.
1
(HAND TIGHTEN)
PUTTY
(IF REQUIRED)
3
POP-UP
CABLE
4
4
SINK OR
MOUNTING
SURFACE
Fig. B.
3
2
2
1
2
POP-UP DRAIN
Fig. B.
Fig. A.
Remove CLEAR PLASTIC COVER (1).
1
Remove CARDBOARD SPACER (2) from under
DRAIN POP-UP (3).
DRAIN
BODY
3
Tighten TAILPIECE (4) on DRAIN BODY before
installing DRAIN BODY. Fig. B.
2
3
REMOVE FLANGE
Thread FLANGE (1) counter-clockwise and
remove FLANGE (1) and FOAM GASKET (2)
from drain body. Fig. A.
4
Fig. A.
1
Fig. B.
Thread LOCKNUT (3) clock-wise to bottom of
drain body. Push GASKET (4) down against
LOCKNUT (3). Fig. B.
4
2
3
4
5
INSTALL DRAIN FROM
BELOW FIXTURE
From under side of SINK
install DRAIN BODY (1) up
through drain outlet.
Note: No plumber’s putty
or caulk is required.
The CABLE ATTACHMENT
POINT (2) must face towards
the rear of the SINK.
REAR
OF
SINK
4
Tighten LOCKNUT (1) firmly with Adjustable
Wrench or Channel Locks.
DRAIN
OUTLET
3
FLANGE GASKET AND POP-UP KNOB
1
1
Install FOAM GASKET (3)
and FLANGE (4) onto drain
body from above SINK and
tighten FLANGE (4) firmly.
6
TIGHTEN LOCKNUT
2
Fig. A.
Fig. B.
Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET (3) is fully compressed
and not visible. Fig. A.
POP-UP KNOB (1) must be fully down. Fig. B.
DOWN
1
WHITE FOAM
GASKET
NOT VISIBLE
DRAIN
FLANGE
M968843 Rev. 1.2
2
7
ATTACH CABLE CONNECTOR
Fig. A.
Fig. B.
Thread CABLE CONNECTOR (1) clockwise
onto DRAIN BODY CONNECTION (2) and
hand tighten. Fig. A.
1
Your new POP-UP DRAIN installation is
now complete. Fig. B.
Note: Tailpeice on pop-up drain is 1-1/4” O.D.
Fig. B.
2
1-1/4” O.D.
8
CHECK OPERATION OF POP-UP
Operate LIFT KNOB (1) to verify that STOPPER (2) opens and
closes.
1
Note: If STOPPER (2) does not open and close properly then refer
to the “troubleshooting section” of these instructions.
2
9
MAKE WATER SUPPLY AND WASTE CONNECTIONS
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE
PURCHASED SEPARATELY.
Connect water supply to FAUCET (1) with 1/2" IPS FLEXIBLE
SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3).
Use adjustable wrench to tighten connections. Do not over tighten.
Be careful not to kink copper supply when bending. Use tubing
cutter to cut to proper length.
Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to
waste outlet.
1/2" PIPE
THREAD
1
COUPLING
NUT
2
FLEXIBLE
SUPPLIES
3
3/8 O.D.
BULL-NOSE
RISERS
3/8” COMPRESSION
CONNECTION
COMPRESSION
NUT
FERRULE
HOT
COLD
M968843 Rev. 1.2
3
10
TEST INSTALLED FITTING
With HANDLES (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
1
4
Remove AERATOR (3).
Operate both HANDLES (1) to flush water lines thoroughly.
Replace AERATOR (3).
1
CHECK DRAIN CONNECTIONS
Operate POP-UP KNOB (4) and fill lavatory with water.
Check that DRAIN STOPPER (5) makes a good seal
and retains water in SINK. If DRAIN STOPPER (5)
does not seal properly, please refer to Troubleshooting
section in these instructions.
3
Release POP-UP KNOB (4) down and check all drain
connections and "P" trap for leaks.
Tighten
if necessary.
5
WASTE
OUTLET
2
2
11
“P” TRAP
SERVICE
2
To change direction of handle rotation, proceed as follows:
1
Turn VALVE in OFF position.
Loosen HANDLE SCREW (1).
4
Pull HANDLE (2) off ADAPTER (3). Loosen ADAPTER
SCREW (4) and pull off ADAPTER (3).
90˚
Turn ADAPTER (3) 90˚ in a way that flat in ADAPTER (3)
catches the other flat on VALVE STEM (5).
3
Reinstall ADAPTER SCREW (4) and LEVER HANDLE (2).
Tighten HANDLE SCREW (1).
5
If spout drips, operate handles several times
from OFF to ON position. Do not force - handles
turn only 90˚.
12
FLAT
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER.DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
M968843 Rev. 1.2
4
Speed Connect™ Drain
Troubleshooting Guide
If sink does not hold water even though Stopper is in the “down” position:
• Follow CABLE ADJUSTMENT PROCEDURE.
If Stopper does not raise up fully or sink drains too slowly:
• Follow CABLE ADJUSTMENT PROCEDURE.
If you need to remove the Stopper:
• Follow STOPPER REMOVAL PROCEDURE.
If you would like the ability to remove your Stopper simply by lifting it out of the drain:
• Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
CABLE ADJUSTMENT PROCEDURE
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
Look at the area on the Drain Body where the Cable was attached and locate the component labeled as
“Cam” in the illustration. Fig. B.
Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the
Stopper should be in the UP position. Fig. B, C.
Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.
Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the
Drain Body Connection (2) and hand-tighten. Fig. A.
Fig. A.
Fig. B. Fig. C.
DOWN
CAM
1
RE-ATTACH
STOPPER
CAM CAP
DISCONNECT
2
STOPPER REMOVAL PROCEDURE
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
Look at the area on the Drain Body where the Cable was attached and locate the component labeled
as “Cam” and “Cam Cap” in the illustration. Fig. B.
Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.
Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.
The Stopper can now be removed by lifting it out of the Drain. Fig. F.
Fig. D.
Fig. E.
REMOVE
CAM
Fig. F.
REMOVE
CAM CAP
M968843 Rev. 1.2
5
STOPPER INSTALLATION PROCEDURE
The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be
removed) or “Unlock” Mode (Stopper is removable).
Locked Mode:
Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper. Fig. G.
To install the stopper in “Locked” mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the rear of the
Sink and the American Standard logo is facing front. Rotate
Stopper slightly if necessary so that the Stopper slides all the
way down.Fig. G.
Fig. G.
LOGO
Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted. Fig. J.
LOOP TOWARD
REAR OF SINK
Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted. Fig. K.
DRAIN
Locked Mode
(Vandal Proof)
Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
Troubling Shooting Guide to complete installation. Stopper will be
in “Locked” mode and not be removable.
Unlocked Mode:
Fig. H.
Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper. Fig. H.
LOGO
To install the stopper in “Unlocked” mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the front of the
Sink and the American Standard logo is facing rear. Rotate Stopper
slightly if necessary so that the Stopper slides all the way down.
Fig. H.
Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted. Fig. J.
LOOP TOWARD
FRONT OF SINK
Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted. Fig. K.
DRAIN
Unlocked Mode
Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
“Troublingshooting Guide” to complete installation. Stopper will be
in “Unlocked” mode and removable.
Fig. J.
CAM
INSTALL CAM
Fig. K.
INSTALL
CAM CAP
M968843 Rev. 1.2
6
PRINCETON
Center Set Faucet
4508.201
M916808-YYY0A
METAL LEVER HANDLE
M918075-0070A
M918504-0070A
HANDLE SCREW
M918021-0070A
ADAPTER
M962473-YYY0A
LIFT ROD AND KNOB
M904900-0070A
VALVE NUT
Replace the "YYY" with
appropriate finish code
M913806-0070A
BEARING WASHER
CHROME
SATIN NICKLE
A954120-0070A
VALVE
066070-YYY0A
AERATOR
002
295
M962544-YYY0A
STOPPER
ASSEMBLY
M952430-0070A
CABLE ASSEMBLY
M962457-YYY0A
FLANGE
ASSEMBLY
M923058-0070A
PUTTY PLATE
M952425-YYY0A
DRAIN ASSEMBLY
065800-0070A
ATTACHMENT NUT
M922872-0070A
CAM SEAT INSERT
M919660-0020A
6” TAILPIECE
(NOT INCLUDED
WITH FAUCET)
M962552-0070A
CAM ASSEMBLY
M913207-0070A
TAILPIECE INSERT
066116-YYY0A
DRAIN STOPPER
M953450-YYY0A
COMPLETE
DRAIN ASSEMBLY
066118-0070A
PIVOT ROD KIT
066117-YYY0A
2" FLANGE KIT
M962401-YYY0A
LIFT ROD AND KNOB
A919661-0020A
TAILPIECE
072574-0070A
EXTENSION ROD
M962458-0070A
DRAIN MOUNTING KIT
070847-0070A
CLIP
M961711-0070A
TAILPIECE INSERT
M968843 Rev. 1.2
070532-0040A
TAILPIECE
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-12-00
POP-UP DRAIN ASSEMBLY
BEFORE 04/06
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2008
7