American Standard 6074.XXX Indoor Furnishings User Manual

Installation
Instructions
6074.XXX
BELLFLOWER
Centerset Lavatory Faucet with the
Speed Connect™ Drain
Congratulations on purchasing your American Standard faucet with
the Speed Connect Drain, a feature found only on
American Standard faucets.
Speed Connect Drain*
• 1/3 of the parts, installs in 1/3 of the time
• No tools needed
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
Certified to comply with ANSI A112.18.1
M968633
*Your new American Standard faucet is designed to work only with the Speed Connect drain. Helpful tips for
removing your current drain can be found in the Troubleshooting section of these instructions.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Recommended tools
Screwdriver
1
Channel Locks
INSTALL FAUCET
CAUTION
Adjustable Wrench
Tubing Cutter
Turn off hot and cold water
supplies before beginning.
Turn off hot and cold water supplies before beginning.
Insert FAUCET (1) and CABLE CONNECTOR (2) through
mounting holes of Sink or mounting surface. Fig. A.
Fig. A.
Assemble LOCKNUTS (3) onto SHANKS (4) ( from under
side of Sink. Hand tighten firmly. Fig. B.
(HAND TIGHTEN)
3
1
4
Fig. B.
POP-UP
CABLE
SINK OR
MOUNTING
SURFACE
3
2
2
1
2
INSTALL POP-UP DRAIN
Fig. A.
Remove CLEAR PLASTIC COVER (1). Remove
CARDBOARD SPACER (2) from under DRAIN
POP-UP (3). Fig. A.
REAR OF
SINK
1
3
Drop DRAIN BODY (4) through sink drain
hole. Make sure WHITE FOAM GASKET (5)
is under flange of DRAIN BODY (4). Fig. B.
Note: No plumber’s putty or caulk is required.
Fig. B.
4
6
5
2
SINK
DRAIN
HOLE
The CABLE ATTACHMENT POINT (6) must
face towards the rear of the SINK. Fig. B.
3
INSTALL BLACK GASKET
Install BLACK CONE GASKET (1) onto DRAIN BODY (2)
from below.
Note: The flat side of the BLACK CONE GASKET (1) must
face down.
2
1
FLAT SIDE OF GASKET
MUST FACE DOWN
4
INSTALL GRAY LOCKNUT
Fig. B.
Fig. A.
Install GRAY LOCKNUT (1) onto DRAIN BODY (2)
from below SINK. Fig. A.
Note: The flat side of the GRAY LOCKNUT (1)
must face up.
2
Tighten firmly by hand. No tools are required.
Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET (3) is fully compressed
and not visible. Fig. B.
DRAIN
FLANGE
FLAT SIDE OF
GRAY LOCKNUT
MUST FACE UP
3
1
5
POP-UP KNOB
WHITE FOAM
GASKET
NOT VISIBLE
DOWN
POP-UP KNOB (1) must be fully down.
1
UP
M968633
2
6
ATTACH CABLE CONNECTOR
Fig. A.
Fig. B.
Thread CABLE CONNECTOR (1) clockwise
onto DRAIN BODY CONNECTION (2) and
hand tighten. Fig. A.
1
Your new POP-UP DRAIN installation is
now complete. Fig. B.
Note: Tailpeice on pop-up drain is 1-1/4” O.D.
Fig. B.
1-1/4” O.D.
2
7
CHECK OPERATION OF POP-UP
Operate LIFT KNOB (1) to verify that STOPPER (2) opens and
closes. Fig. B.
Note: If STOPPER (2) does not open and close properly then refer
to the “troubleshooting section” of these instructions.
1
2
8
MAKE WATER SUPPLY AND WASTE CONNECTIONS
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE
PURCHASED SEPARATELY.
Connect water supply to FAUCET (1) with 1/2" IPS FLEXIBLE
SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3).
Use adjustable wrench to tighten connections. Do not over tighten.
Be careful not to kink copper supply when bending. Use tubing
cutter to cut to proper length.
Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to
waste outlet.
1
1/2" PIPE
THREAD
COUPLING
NUT
2
FLEXIBLE
SUPPLIES
3
3/8 O.D.
BULL-NOSE
RISERS
3/8” COMPRESSION
CONNECTION
COMPRESSION
NUT
FERRULE
HOT
COLD
M968633
3
9
TEST INSTALLED FITTING
With HANDLES (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
3
6
Remove AERATOR HOUSING (6). (Turn counter-clockwise).
Remove AERATOR INSERT (3) from AERATOR HOUSING (6).
REMOVE
1
Operate both HANDLES (1) to flush water lines thoroughly.
4
Replace AERATOR (3) and AERATOR HOUSING (6).
CHECK DRAIN CONNECTIONS
Operate POP-UP KNOB (4) and fill lavatory with water.
Check that DRAIN STOPPER (5) makes a good seal
and retains water in SINK. If DRAIN STOPPER (5)
does not seal properly, please refer to Troubleshooting
section in these instructions.
Release POP-UP KNOB (5) down and check all drain
connections and "P" trap for leaks.
Tighten
if necessary.
5
WASTE
OUTLET
2
10
“P” TRAP
SERVICE
2
1
To change direction of handle
rotation, proceed as follows:
2
3
Turn VALVE to OFF position. Pull out INDEX BUTTON (1).
Remove HANDLE SCREW (2), and pull HANDLE (3) off of
ADAPTOR (4).
Pull ADAPTOR (4) off VALVE STEM (5) and turn 90˚ in a way that
flat in ADAPTOR (4) catches a different flat on VALVE STEM (5).
Reinstall ADAPTER (4), HANDLE (3) and HANDLE SCREW (2).
4
Push in INDEX BUTTON (1).
AERATOR (6) may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR (6) and rinse clean. See step 9 above.
90˚
6
5
If Faucet Drips Proceed As Follows:
Turn VALVE in OFF position.
FLAT
If spout drips, operate HANDLES (1) several times from
OFF to ON position. Do not force-handles turn only 90˚.
11
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
M968633
4
Speed Connect™ Drain
Troubleshooting Guide
If sink does not hold water even though Stopper is in the “down” position:
• Follow CABLE ADJUSTMENT PROCEDURE.
If Stopper does not raise up fully or sink drains too slowly:
• Follow CABLE ADJUSTMENT PROCEDURE.
If you need to remove the Stopper:
• Follow STOPPER REMOVAL PROCEDURE.
If you would like the ability to remove your Stopper simply by lifting it out of the drain:
• Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
CABLE ADJUSTMENT PROCEDURE
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
Look at the area on the Drain Body where the Cable was attached and locate the component labeled as
“Cam” in the illustration. Fig. B.
Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the
Stopper should be in the UP position. Fig. B, C.
LIFTKNOB
Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.
Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the
Drain Body Connection (2) and hand-tighten. Fig. A.
Fig. A.
CAM
Fig. B.
Fig. C.
DOWN
1
RE-ATTACH
LIFTKNOB
CAM CAP
DISCONNECT
STOPPER
2
STOPPER REMOVAL PROCEDURE
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
Look at the area on the Drain Body where the Cable was attached and locate the component labeled
as “Cam” and “Cam Cap” in the illustration. Fig. B.
Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.
Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.
The Stopper can now be removed by lifting it out of the Drain. Fig. F.
Fig. D.
Fig. E.
REMOVE
CAM
Fig. F.
REMOVE
CAM CAP
M968633
5
STOPPER INSTALLATION PROCEDURE
The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be
removed) or “Unlock” Mode (Stopper is removable).
Locked Mode:
Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper. Fig. G.
To install the stopper in “Locked” mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the rear of the
Sink and the American Standard logo is facing front. Rotate
Stopper slightly if necessary so that the Stopper slides all the
way down.Fig. G.
Fig. G.
LOGO
Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted. Fig. J.
LOOP TOWARD
REAR OF SINK
Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted. Fig. K.
DRAIN
Locked Mode
(Vandal Proof)
Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
Troubling Shooting Guide to complete installation. Stopper will be
in “Locked” mode and not be removable.
Unlocked Mode:
Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper. Fig. H.
To install the stopper in “Unlocked” mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the front of the
Sink and the American Standard logo is facing rear. Rotate Stopper
slightly if necessary so that the Stopper slides all the way down.
Fig. H.
Fig. H.
LOGO
180˚
Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted. Fig. J.
LOOP TOWARD
FRONT OF SINK
Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted. Fig. K.
DRAIN
Unlocked Mode
Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
“Troublingshooting Guide” to complete installation. Stopper will be
in “Unlocked” mode and removable.
Fig. J.
CAM
INSTALL CAM
Fig. K.
INSTALL
CAM CAP
M968633
6
TIPS FOR REMOVING YOUR OLD DRAIN:
Most existing drains can be removed quickly and easily with only a pair of channellock pliers or a wrench. However, there may be situations where it is difficult to
remove your old drain or determine how the drain is disassembled. Depending upon
the existing Drain in your sink, it is either removed from above or below the sink.
The illustrations below show some typical drain installations and how they are disassembled from the sink.
The following tips can help with some of the more common challenges in drain removal:
Loosen nuts on P-Trap using channel locks. Suggest spraying nuts with spray lubricant to loosen any corrosion or
debris that may have built up. Remove P-Trap half from Tailpiece. Use bucket to catch any residual water in P-trap.
Unthread Pivot Rod Nut from Drain Body and remove. Pull Stopper out from Drain Body.
For Drains that are removed from below Sink:
Loosen Mounting Nut as far down as it will go. Push Drain Body up into Sink and unthread Metal Flange from Drain
Body. Remove Drain Body from below sink.
For Drains that are removed from above Sink:
Unthread Tailpiece from Drain Body.
Loosen and remove Mounting Nut and Gasket on Drain Body using channel locks. Suggest spraying nut with spray
lubricant to loosen any corrosion or debris that may have built up. Push Drain Body up into the Sink and remove.
Note: If Drain body rotates while loosening Mounting Nut, insert a screw driver into overflow hole to prevent Drain
Body from rotating while Mounting Nut is removed.
Recommended tools
Channel Locks
Adjustable Wrench
WHEN DRAIN IS REMOVED
FROM BELOW SINK
METAL OR PLASTIC TWO PIECE
DRAIN BODY
Phillips Screwdriver
WHEN DRAIN IS REMOVED FROM ABOVE SINK
METAL DRAIN BODY WITH
PLASTIC TAILPIECE
PLASTIC DRAIN BODY
WITH PLASTIC TAILPIECE
SCREWDRIVER
STOPPER
METAL
DRAIN
BODY
STOPPER
UNTHREAD
METAL
FLANGE
SINK
FINISHED
WALL
PLASTIC
DRAIN BODY
SINK
METAL OR
PLASTIC
DRAIN BODY
PIVOT
ROD NUT
STOPPER
MOUNTING
NUT
SINK
MOUNTING
NUT and
GASKET
PIVOT
ROD NUT
PIVOT
ROD NUT
PLASTIC
TAILPIECE
P-TRAP
HALF
P-TRAP
HALF
FINISHED
WALL
MOUNTING
NUT and
GASKET
PLASTIC
TAILPIECE
FINISHED
WALL
P-TRAP
HALF
M968633
7
BELLFLOWER
Centerset Lavatory Faucet with
Speed Connect™ Drain
MODEL NUMBER
M907024-YYY0A
INDEX BUTTON
6074.XXX
M918518-0070A
HANDLE SCREW
M962667-YYY0A
HANDLE ASSEMBLY
(LEFT HAND)
M962668-YYY0A
HANDLE ASSEMBLY
(RIGHT HAND)
Replace the "YYY" with
appropriate finish code
CHROME
M950209-YYY0A
LIFT ROD AND KNOB
M918051-0070A
HANDLE ADAPTER
002
M904900-0070A
VALVE NUT
M913806-0070A
BEARING WASHER
M910271-0070A
AERATOR INSERT
A954120-0070A
VALVE
M962543-YYY0A
STOPPER
ASSEMBLY
M901677-0070A
PUTTY PLATE
M913208-0070A
SPONGE WASHER
065800-0070A
ATTACHMENT NUT
M952410-YYY0A
DRAIN ASSEMBLY
M962551-0070A
CAM ASSEMBLY
M952430-0070A
CABLE ASSEMBLY
M962431-0070A
DRAIN MOUNTING KIT
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-12-00
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2008
M968633
8