- Home
- Domestic appliances
- Climate control
- Space heaters
- American Standard
- 754323-100 Rev A
- Installation Guide
advertisement
▼
Scroll to page 2
of 23
INSTALLATION GUIDE FOR GREEN TEA™ 5' x 36" MODEL 3571 GREEN TEA™ 5-1/2' x 36" MODEL 3572 GREEN TEA™ 6' x 36" MODEL 3573 GREEN TEA™ 5' x 42" MODEL 3574 GREEN TEA™ 6' x 42" MODEL 3575 TOWN SQUARE® 5' x 42" MODEL 2748 TOWN SQUARE® 6' x 42" MODEL 2742 ELLISSE OVAL MODEL 2709 COMBINATION WHIRLPOOL AND AIR BATH SYSTEMS WITH CHROMATHERAPY LIGHTS THANK YOU... for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The Air Massage System is completely assembled with air pump, motor, lights, and system piping. All you need to finish the installation are your selected fittings and electrical connections for an Air Massage System. To insure maximum performance and pleasure from this product, please follow the instructions and cautions. FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS. © AS America, Inc. 2009 All product names listed herein are trademarks of AS America, Inc. unless otherwise noted. 1 754323-100 Rev A TABLE OF CONTENTS: Cover................................................................................................Page 1 Table of Contents..............................................................................Page 2 Safety Instructions Notice.................................................................Page 3 Roughing-in Reference.....................................................................Page 4 - 12 Installation and Framing Instructions................................................Page 13 - 16 Supplied Drain Assembly and Installation Instructions.....................Page 16 - 20 Post Installation Instructions.............................................................Page 21 Remote Blower Location Option.......................................................Page 22 Warranty...........................................................................................Page 23 754323-100 Rev A 2 IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS! ! WARNING: Risk of personal injury. Do not permit children to use this bathtub without adult supervision. ! WARNING: Risk of electric shock. Do not permit electrical appliances near any bathtub when bathtub contains water. ! WARNING: Risk of hyperthermia and possible drowning. People using medications and/or having adverse medical history should consult a physician before using this product. ! WARNING: Risk of personal injury. Do not overfill bathtub before entering. Entering tub when filled more than 2/3 can cause overflow and slippery conditions. Exercise caution when entering and exiting. ! WARNING: No Food or Alcoholic Beverages. Use of your bathtub immediately after meals is not recommended. Avoid alcohol consumption before or during bathing. Alcoholic beverages can cause drowsiness or hyperthermia resulting in loss of consciousness or even drowning. ! WARNING: Pregnancy. If you are or think you may be pregnant, consult your physician before using the bathtub. Use this unit only for its intended use as described in this manual. Do not use any attachments not recommended by American Standard. The unit must be connected only to a supply circuit that is properly protected by a ground-fault circuit-interrupter (GFCI). Such a GFCI should be provided by the installer and should be tested on a routine basis. To test the GFCI, push the test button. The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the bathtub without the test button being pushed, a ground current is flowing, indicating the possibility of an electric shock. Do not use this air bath. Disconnect the air bath and have the problem corrected by a licensed electrician before using. SAVE THESE INSTRUCTIONS 3 754323-100 Rev A ROUGHING-IN REFERENCES GREEN TEA™ 5' x 36" MODEL 3571 COMBINATION SYSTEM 60 (1524mm) TOP VIEW OUTLINE OF CUTOUT 58.5 x 34.5 (1486 x 876mm) 14-3/4 (375mm) 11-1/2 (292mm) 36 (914mm) ACCESS AIR BLOWER, PUMP MOTOR, WHIRLPOOL HEATER AND LIGHTING SYSTEM AT THIS END OF TUB 9 (229mm) CL CUTOUT IN FLOOR FOR DRAIN CONTROL PANELS 8 WHIRLPOOL JETS END VIEW 51mm (2") CL TO OVERFLOW 102mm (4") 559mm (22") 20 AIR JETS LEVELING STRINGER NOT FOR SUPPORT INTEGRAL FEET WITH ATTACHED BASEBOARD ROUGH FLOOR 508mm (20") NOTE: INSTALLER MUST PROVIDE 12 X 24 ACCESS OPENING FOR SERVICING AIR BLOWER, PUMP MOTOR, WHIRLPOOL HEATER, AND LIGHTING SYSTEM. THIS MODEL INCLUDES A DRAIN ASSEMBLY. OTHER DRAIN ASSEMBLIES CANNOT BE USED. REVIEW DRAIN INSTALLATION DETAILS IN THE DOCUMENT TO FULLY UNDERSTAND FLOOR CUTOUT REQUIREMENTS. 754323-100 Rev A 4 ROUGHING-IN REFERENCES GREEN TEA™ 5-1/2' x 36" MODEL 3572 COMBINATION SYSTEM 66 (1676mm) TOP VIEW OUTLINE OF CUTOUT 64.5 x 34.5 (1638 x 876mm) 14-3/4 (292mm) 11-1/2 (292mm) ACCESS AIR BLOWER, PUMP MOTOR, WHIRLPOOL HEATER AND LIGHTING SYSTEM AT THIS END OF TUB 36 (914mm) 9 (229mm) CL CUTOUT IN FLOOR FOR DRAIN 8 WHIRLPOOL JETS 51mm (2") END VIEW CONTROL PANELS CL TO OVERFLOW 102mm (4") 559mm (22") 22 AIR JETS LEVELING STRINGER NOT FOR SUPPORT INTEGRAL FEET WITH ATTACHED BASEBOARD ROUGH FLOOR 508mm (20") NOTE: INSTALLER MUST PROVIDE 12 X 24 ACCESS OPENING FOR SERVICING AIR BLOWER, PUMP MOTOR, WHIRLPOOL HEATER, AND LIGHTING SYSTEM. THIS MODEL INCLUDES A DRAIN ASSEMBLY. OTHER DRAIN ASSEMBLIES CANNOT BE USED. REVIEW DRAIN INSTALLATION DETAILS IN THE DOCUMENT TO FULLY UNDERSTAND FLOOR CUTOUT REQUIREMENTS. 5 754323-100 Rev A ROUGHING-IN REFERENCES GREEN TEA™ 6' x 36" MODEL 3573 COMBINATION SYSTEM TOP VIEW 72 (1829mm) 14-3/4 (375mm) 11-1/2 (292mm) OUTLINE OF CUTOUT 70.5 x 34.5 (1780 x 876mm) ACCESS AIR BLOWER, PUMP MOTOR, WHIRLPOOL HEATER AND LIGHTING SYSTEM AT THIS END OF TUB 36 (914mm) 9 (229mm) CL CUTOUT IN FLOOR FOR DRAIN 10 WHIRLPOOL JETS 51mm (2") CL TO OVERFLOW 102mm (4") CONTROL PANELS 23 AIR JETS LEVELING STRINGER NOT FOR SUPPORT END VIEW 559mm (22") INTEGRAL FEET WITH ATTACHED BASEBOARD ROUGH FLOOR 508mm (20") NOTE: INSTALLER MUST PROVIDE 12 X 24 ACCESS OPENING FOR SERVICING AIR BLOWER, PUMP MOTOR, WHIRLPOOL HEATER, AND LIGHTING SYSTEM. THIS MODEL INCLUDES A DRAIN ASSEMBLY. OTHER DRAIN ASSEMBLIES CANNOT BE USED. REVIEW DRAIN INSTALLATION DETAILS IN THE DOCUMENT TO FULLY UNDERSTAND FLOOR CUTOUT REQUIREMENTS. 754323-100 Rev A 6 ROUGHING-IN REFERENCES GREEN TEA™ 5' x 42" MODEL 3574 COMBINATION SYSTEM 60 (1524mm) TOP VIEW OUTLINE OF CUTOUT 58.5 x 40.5 (1486 x 1029mm) 14-3/4 (375mm) 11-1/2 (292mm) 42 (1067mm) ACCESS AIR BLOWER, PUMP MOTOR, WHIRLPOOL HEATER AND LIGHTING SYSTEM AT THIS END OF TUB 9 (229mm) CL CUTOUT IN FLOOR FOR DRAIN CONTROL PANELS 8 WHIRLPOOL JETS END VIEW 51mm (2") CL TO OVERFLOW 102mm (4") 559mm (22") 23 AIR JETS LEVELING STRINGER NOT FOR SUPPORT INTEGRAL FEET WITH ATTACHED BASEBOARD ROUGH FLOOR 508mm (20") NOTE: INSTALLER MUST PROVIDE 12 X 24 ACCESS OPENING FOR SERVICING AIR BLOWER, PUMP MOTOR, WHIRLPOOL HEATER, AND LIGHTING SYSTEM. THIS MODEL INCLUDES A DRAIN ASSEMBLY. OTHER DRAIN ASSEMBLIES CANNOT BE USED. REVIEW DRAIN INSTALLATION DETAILS IN THE DOCUMENT TO FULLY UNDERSTAND FLOOR CUTOUT REQUIREMENTS. 7 754323-100 Rev A ROUGHING-IN REFERENCES GREEN TEA™ 6' x 42" MODEL 3575 COMBINATION SYSTEM TOP VIEW 72 (1829mm) OUTLINE OF CUTOUT 70.5 x 40.5 (1780 x 1029mm) 14-3/4 (375mm) 11-1/2 (292mm) 42 (1067mm) ACCESS AIR BLOWER, PUMP MOTOR, WHIRLPOOL HEATER AND LIGHTING SYSTEM AT THIS END OF TUB 9 (229mm) CL CUTOUT IN FLOOR FOR DRAIN 10 WHIRLPOOL JETS END VIEW 51mm (2") CL TO OVERFLOW 102mm (4") 559mm (22") CONTROL PANELS 27 AIR JETS LEVELING STRINGER NOT FOR SUPPORT INTEGRAL FEET WITH ATTACHED BASEBOARD ROUGH FLOOR 508mm (20") NOTE: INSTALLER MUST PROVIDE 12 X 24 ACCESS OPENING FOR SERVICING AIR BLOWER, PUMP MOTOR, WHIRLPOOL HEATER, AND LIGHTING SYSTEM. THIS MODEL INCLUDES A DRAIN ASSEMBLY. OTHER DRAIN ASSEMBLIES CANNOT BE USED. REVIEW DRAIN INSTALLATION DETAILS IN THE DOCUMENT TO FULLY UNDERSTAND FLOOR CUTOUT REQUIREMENTS. 754323-100 Rev A 8 ROUGHING-IN REFERENCES TOWN SQUARE® 5' x 42" MODEL 2748 COMBINATION SYSTEM CONTROL PANELS 59-1/2" (1511mm) TOP VIEW INTEGRAL FITTING DECK 2-1/2" X 14" (64 X 356mm) 29-3/4" (755mm) 14-1/2" (368mm) 3" (76mm) 7-3/4" TYPICAL (197mm) 41-5/8" (1057mm) FLOOR CUTOUT 9" X 18" (229 X 458mm) OUTLINE OF CUTOUT 58" X 40-1/8" (1473 X 1019mm) 20 AIR JETS 3/4" (19mm) OUTLINE OF SKID RESISTANT SURFACE 6 WHIRLPOOL JETS ACCESS AIR BLOWER, PUMP MOTOR, WHIRLPOOL HEATER AND LIGHTING SYSTEM AT THIS END OF TUB LEVELING STRINGER (NOT FOR SUPPORT) END VIEW 23" (584mm) 21" (533mm) ROUGH FLOOR INTEGRAL FEET WITH ATTACHED BASEBOARD NOTE: INSTALLER MUST PROVIDE 12 X 24 ACCESS OPENING FOR SERVICING AIR BLOWER, PUMP MOTOR, WHIRLPOOL HEATER, AND LIGHTING SYSTEM. THIS MODEL INCLUDES A DRAIN ASSEMBLY. OTHER DRAIN ASSEMBLIES CANNOT BE USED. REVIEW DRAIN INSTALLATION DETAILS IN THE DOCUMENT TO FULLY UNDERSTAND FLOOR CUTOUT REQUIREMENTS. 29-3/4 (755mm) TO END OF TUB C/L DRAIN FITTINGS DECK FOR SPOUT & VALVES FOR HAND SPRAY 1-1/2 (38mm) 1-1/2 (38mm) 2-1/2 (64mm) 4-1/2 4-1/2 5 (114mm) (114mm) (127mm) EDGE OF FITTINGS 1-1/2 (38mm) DECK HOLE DRILLING LOCATION FOR AMERICAN STANDARD "TOWN SQUARE" DECK MOUNT BATH FILLER WITH PERSONAL SHOWER, MODEL #2555.901 ONLY 9 754323-100 Rev A ROUGHING-IN REFERENCES TOWN SQUARE® 6' x 42" MODEL 2742 COMBINATION SYSTEM CONTROL PANELS 71-1/2" (1816mm) TOP VIEW 35-3/4" (908mm) 13-1/4" (337mm) INTEGRAL FITTING DECK 2-1/4" X 14" (57 X 356mm) 3" (76mm) EDGE OF FLOOR CUTOUT 10-1/4” (260mm) 26-3/4 (679mm) 8 WHIRLPOOL JETS 7-3/4” TYPICAL (197mm) FLOOR CUTOUT 9" X 19" (229 X 459mm) AIR BLOWER 3/4" 41-3/4" (19mm) (1060mm) OUTLINE OF SKID RESISTANT SURFACE ACCESS AIR BLOWER, PUMP MOTOR, WHIRLPOOL HEATER AND LIGHTING SYSTEM AT THIS END OF TUB 20 AIR JETS OUTLINE OF CUTOUT 70" X 40-1/4" (1778 X 1022mm) LEVELING STRINGER (NOT FOR SUPPORT) 2" (51mm) END VIEW 22" (559mm) 3-1/4" (83mm) 20" (508mm) ROUGH FLOOR INTEGRAL FEET WITH ATTACHED BASEBOARD NOTE: INSTALLER MUST PROVIDE 12 X 24 ACCESS OPENING FOR SERVICING AIR BLOWER, PUMP MOTOR, WHIRLPOOL HEATER, AND LIGHTING SYSTEM. THIS MODEL INCLUDES A DRAIN ASSEMBLY. OTHER DRAIN ASSEMBLIES CANNOT BE USED. REVIEW DRAIN INSTALLATION DETAILS IN THE DOCUMENT TO FULLY UNDERSTAND FLOOR CUTOUT REQUIREMENTS. 35-3/4 (908mm) TO END OF TUB C/L DRAIN FITTINGS DECK FOR SPOUT & VALVES FOR HAND SPRAY 1-1/2 (38mm) 1-1/2 (38mm) 2-1/2 (64mm) 4-1/2 4-1/2 5 (114mm) (114mm) (127mm) EDGE OF FITTINGS 1-1/2 (38mm) DECK HOLE DRILLING LOCATION FOR AMERICAN STANDARD "TOWN SQUARE" DECK MOUNT BATH FILLER WITH PERSONAL SHOWER, MODEL #2555.901 ONLY 754323-100 Rev A 10 ROUGHING-IN REFERENCES ELLISSE OVAL MODEL 2709 COMBINATION SYSTEM TOP VIEW OUTLINE OF CUTOUT 240 mm (9-7/16") 978 mm (38-1/2") 1759 mm (69-1/4") ACCESS AIR BLOWER, PUMP MOTOR, WHIRLPOOL HEATER AND LIGHTING SYSTEM AT THIS END OF TUB 7-3/4" TYPICAL (197mm) FLOOR CUTOUT 229 X 459mm (9" X 19") 489mm (19-1/4") CONTROL PANELS 16 AIR JETS END VIEW 38mm (1-1/2") 6 WHIRLPOOL JETS C L TO OVERFLOW 86mm (3-3/8") INTEGRAL FEET WITH ATTACHED BASEBOARD 533mm (21") 495mm (19-1/2") ROUGH FLOOR NOTE: INSTALLER MUST PROVIDE 12 X 24 ACCESS OPENING FOR SERVICING AIR BLOWER, PUMP MOTOR, WHIRLPOOL HEATER, AND LIGHTING SYSTEM. THIS MODEL INCLUDES A DRAIN ASSEMBLY. OTHER DRAIN ASSEMBLIES CANNOT BE USED. REVIEW DRAIN INSTALLATION DETAILS IN THE DOCUMENT TO FULLY UNDERSTAND FLOOR CUTOUT REQUIREMENTS. 11 754323-100 Rev A ROUGHING-IN REFERENCES GREEN TEA™ 5-1/2' x 36" MODEL 3572 COMBINATION SYSTEM GREEN TEA™ 5' x 36" MODEL 3571 COMBINATION SYSTEM GENERAL SPECIFICATIONS FOR 3571 COMBINATION SYSTEM INSTALLED SIZE WEIGHT WEIGHT w/WATER GAL. TO OVERFLOW MIN. OPERATING GAL. BATHING WELL AT SUMP BATHING WELL AT RIM WATER DEPTH TO OVERFLOW FLOOR LOADING (PROJECTED AREA) PTS. CUBE (FT 3 ) GENERAL SPECIFICATIONS FOR 3572 COMBINATION SYSTEM 60 x 36 x 22 In. (1524 x 914 x 559mm) 117 Lbs. (53 Kg.) 550 Lbs. (250 Kg.) 52 Gal. (197 L.) 38 Gal. (144 L.) 19 x 43 In. (483mm x 1092mm) 48-1/2 x 27 In. (1232mm x 686mm) 14 In. (356mm) 37 Lbs./Sq. Ft. (179 Kgs/Sq. m.) INSTALLED SIZE WEIGHT WEIGHT w/WATER GAL. TO OVERFLOW MIN. OPERATING GAL. BATHING WELL AT SUMP BATHING WELL AT RIM WATER DEPTH TO OVERFLOW FLOOR LOADING (PROJECTED AREA) PTS. CUBE (FT 3 ) 23.8 44.5 ELECTRICAL SPECIFICATIONS • GREEN TEA™ 5' x 42" MODEL 3574 COMBINATION SYSTEM GENERAL SPECIFICATIONS FOR 3574 COMBINATION SYSTEM GENERAL SPECIFICATIONS FOR 3573 COMBINATION SYSTEM INSTALLED SIZE 59-3/4 x 42 x 22 In. (1518 x 1060 x 559mm) WEIGHT 141 Lbs. (64 Kg.) 682 Lbs. (310 Kg.) WEIGHT w/WATER 65 Gal. (246 L.) GAL. TO OVERFLOW 47 Gal. (178 L.) MIN. OPERATING GAL. 24-1/2 x 42 In. (622mm x 1067mm) BATHING WELL AT SUMP 48 x 33 In. (1219mm x 838mm) BATHING WELL AT RIM 14 In. (356mm) WATER DEPTH TO OVERFLOW 39 Lbs./Sq. Ft. (192 Kgs/Sq. m.) FLOOR LOADING (PROJECTED AREA) 27.8 PTS. CUBE (FT 3 ) 47.4 72 x 36 x 22 In. (1829 x 914 x 559mm) 143 Lbs. (65 Kg.) 693 Lbs. (314 Kg.) 66 Gal. (250 L.) 49 Gal. (185 L.) 19 x 55 In. (483mm x 1397mm) 60-1/2 x 27 In. (1537mm x 686mm) 14 In. (356mm) 38 Lbs./Sq. Ft. (188 Kgs/Sq. m.) 23.8 44.5 ELECTRICAL SPECIFICATIONS • TOWN SQUARE® 5' x 42" MODEL 2748 COMBINATION SYSTEM GREEN TEA™ 6' x 42" MODEL 3575 COMBINATION SYSTEM GENERAL SPECIFICATIONS FOR 3575 COMBINATION SYSTEM GENERAL SPECIFICATIONS FOR 2748 COMBINATION SYSTEM INSTALLED SIZE 59-1/2 x 41-5/8 x 23 In. (1511 x 1057 x 584mm) WEIGHT 110 Lbs. (50 Kg.) WEIGHT w/WATER 611 Lbs. (278 Kg.) GAL. TO OVERFLOW 60 Gal. (227 L) BATHING WELL AT SUMP 34 x 24 In. (864 x 610mm) BATHING WELL AT RIM 52 x 31 In. (1321 x 1321mm) WATER DEPTH TO OVERFLOW 12-1/2 In. (318mm) FLOOR LOADING 29 Lbs./Sq.Ft. (144 Kgs./Sq.m) (PROJECTED AREA) PTS. 27.8 CUBE (FT 3 ) 45.4 72 x 42 x 22 In. (1829 x 1067 x 559mm) 172 Lbs. (78 Kg.) 830 Lbs. (377 Kg.) 79 Gal. (299 L.) 58 Gal. (219 L.) 22-1/2 x 54 In. (572mm x 1372mm) 60 x 33 In. (1524mm x 838mm) 14 In. (356mm) 40 Lbs./Sq. Ft. (193 Kgs/Sq. m.) ELECTRICAL SPECIFICATIONS 25.6 49.4 ELECTRICAL SPECIFICATIONS • • • REFER TO ELECTRICAL INSTALLATION DIAGRAM ON PAGE 14 • REFER TO ELECTRICAL INSTALLATION DIAGRAM ON PAGE 14 TOWN SQUARE® 6' x 42" MODEL 2742 COMBINATION SYSTEM ELLISSE OVAL MODEL 2709 COMBINATION SYSTEM GENERAL SPECIFICATIONS FOR 2742 COMBINATION SYSTEM GENERAL SPECIFICATIONS FOR 2709 COMBINATION SYSTEM INSTALLED SIZE 71-1/2 x 41-3/4 x 22 In. (1816 x 1060 x 559mm) WEIGHT 174 Lbs. (79 Kg.) WEIGHT w/WATER 830 Lbs. (313 Kg.) GAL. TO OVERFLOW 69 Gal. (261 L) BATHING WELL AT SUMP 41 x 21-1/2 In. (1041 x 546mm) BATHING WELL AT RIM 62 x 31-1/2 In. (1574 x 800mm) WATER DEPTH TO OVERFLOW 14-1/4 In. (362mm) FLOOR LOADING 36 Lbs./Sq.Ft. (176 Kgs./Sq.m) (PROJECTED AREA) PTS. 27.8 CUBE (FT 3 ) 55.7 ELECTRICAL SPECIFICATIONS INSTALLED SIZE 69-1/4 x 38-1/2 x 19-3/4 In.(1759 x 978 x 502mm) WEIGHT 119 Lbs. (54 Kg.) WEIGHT w/WATER 652 Lbs. (296 Kg.) GAL. TO OVERFLOW 64 Gal. (243 L) BATHING WELL AT SUMP 45 x 23 In. (1143 x 584mm) BATHING WELL AT RIM 63 x 32 In. (1600 x 813mm) WATER DEPTH TO OVERFLOW 13 In. (330mm) FLOOR LOADING 35 Lbs./Sq.Ft. (172 Kgs./Sq.m) (PROJECTED AREA) PTS. 25.6 CUBE (FT 3 ) 49.4 • ELECTRICAL SPECIFICATIONS • • REFER TO ELECTRICAL INSTALLATION DIAGRAM ON PAGE 14 • REFER TO ELECTRICAL INSTALLATION DIAGRAM ON PAGE 14 754323-100 Rev A • • REFER TO ELECTRICAL INSTALLATION DIAGRAM ON PAGE 14 • REFER TO ELECTRICAL INSTALLATION DIAGRAM ON PAGE 14 INSTALLED SIZE WEIGHT WEIGHT w/WATER GAL. TO OVERFLOW MIN. OPERATING GAL. BATHING WELL AT SUMP BATHING WELL AT RIM WATER DEPTH TO OVERFLOW FLOOR LOADING (PROJECTED AREA) PTS. CUBE (FT 3 ) • • REFER TO ELECTRICAL INSTALLATION DIAGRAM ON PAGE 14 GREEN TEA™ 6' x 36" MODEL 3573 COMBINATION SYSTEM ELECTRICAL SPECIFICATIONS 25.6 45.1 ELECTRICAL SPECIFICATIONS • REFER TO ELECTRICAL INSTALLATION DIAGRAM ON PAGE 14 INSTALLED SIZE WEIGHT WEIGHT w/WATER GAL. TO OVERFLOW MIN. OPERATING GAL. BATHING WELL AT SUMP BATHING WELL AT RIM WATER DEPTH TO OVERFLOW FLOOR LOADING (PROJECTED AREA) PTS. CUBE (FT 3 ) 66 x 36 x 22 In. (1676 x 914 x 559mm) 128 Lbs. (58 Kg.) 619 Lbs. (281 Kg.) 59 Gal. (223 L.) 44 Gal. (167 L.) 19 x 49 In. (483mm x 1245mm) 54-1/2 x 27 In. (1384mm x 686mm) 14 In. (356mm) 38 Lbs./Sq. Ft. (188 Kgs/Sq. m.) 12 FIGURE 1 INSTALLATION AND FRAMING INSTRUCTIONS: TYPICAL INSTALLATION The variety of installations possible for this combination system may require framing procedures other than those shown. Locate studs as required. Ensure roughing-in dimensions are proper, plumb and square. Provisions must be made in all installations for an access opening for servicing the air blower and controls. It is strongly recommended that an additional opening be provided for access to the drain components. The apron should not be used as the primary access opening. 1. Position the combination system into the installation opening and level the deck in both directions, shimming the integral feet with attached baseboard as necessary. Refer to the Combination Installation Table for nominal installation dimensions. Mark the final position of the underside of the deck by tracing a line on to the studs (see Figure 1). D 2. Remove the air massage system and attach a 1 x 4 stringer to the studs, with the top of the stringer touching the traced line. ! The rim of the bath must not support weight. TILE 3. Install supplied cable drain components to the combination system according to the enclosed drain installation instructions. Before replacing your bath for final installation, be certain that an opening has been provided in the sub-floor for the drain. See the roughing-in drawing for suggested opening size (shadowed) and location dimensions. The drain/overflow of the bath extends below the bottom of the bath. Note that this requires a cutout in the floor. WALLBOARD SEALANT TILE BEAD STRIP BATH ADHESIVE 4. Replace combination system and re-shim the integral support feet with attached baseboard, shimming the entire length of the baseboard as needed. Secure the shims using construction adhesive, silicone or equivalent materials. ! LEVELING STRINGER 1 x 4 (not for support) The rim of the bath must not support weight. Any finish material such as tile or wall board must be self-supporting if it contacts the deck of the bath. NOTE: Tile bead kit not included and must be purchased separately. DIM. COMBINATION INSTALLATION TABLE COMBINATION MODEL NUMBER DESCRIPTION 2709 ** 2748 2742 A Nominal tub length recess opening 59-3/4" 1518mm 71-3/4" 1823mm 3571 3572 3573 3574 60-1/4" 1530mm 66-1/4" 1683mm 72-1/4" 1835mm 3575 60" 1524mm 72-1/4" 1835mm B Nominal tub apron support opening 39-3/4" 1511mm 39-3/4" 1511mm 35" 889mm 35" 889mm 35" 889mm 40-3/4" 1035mm 41" 1041mm C Nominal tub width recess opening 36" 914mm 36" 914mm 36" 914mm 41-3/4" 1060mm 42" 1067mm 19" 483mm 19" 483mm 19" 483mm 19" 41-3/4" 1060mm 41-3/4" 1060mm D Nominal tub height opening 21" 533mm 20" E Nominal tub length cutout 58" 1473mm 70" 1778mm F Nominal tub width cutout 508mm 19-1/2" 495mm 19" 483mm 483mm 67" 1702mm 58-1/2" 1486mm 64-1/2" 1638mm 70-1/2" 1791mm 58-1/4" 1480mm 70-1/2" 1791mm 40-1/8" 1019mm 40-1/4" 1022mm 36-1/2" 927mm 34-1/2" 876mm 34-1/2" 876mm 34-1/2" 876mm 40-1/4" 1022mm 40-1/2" 1029mm ** USE CUTOUT TEMPLATE PROVIDED FOR 2709 MODEL NOTICE: DO NOT BUILD THE SURROUNDING STRUCTURE BEFORE RECEIVING YOUR AIR BATH. STRUCTURE MEASUREMENTS SHOULD BE VERIFIED AGAINST THE ACTUAL AIR BATH RECEIVED TO ENSURE PROPER FIT. TYPICAL PIER TYPE INSTALLATION TYPICAL RECESS INSTALLATION AS DESIRED F CUTOUT E CUTOUT D D B 12 (305 mm) C 12 (305 mm) AS DESIRED A NOTE: FRONT EDGE OF BATH MUST BE SUPPORTED BY STUD WALL OR AMERICAN STANDARD APRON KIT LEVELING STRINGERS MOUNTING SURFACE WATERPROOF SEALANT 24 (610 mm) ACCESS PANEL MUST BE LOCATED ON THE SAME SIDE AS THE BLOWER. ALLOW OPEN FRAMING ON BLOWER END FOR SERVICE. BATH UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610mm) IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED. 24 (610 mm) ACCESS PANEL MUST BE LOCATED ON THE SAME SIDE AS THE MOTOR. ALLOW OPEN FRAMING ON PUMP/MOTOR END FOR SERVICE. UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610mm) IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED. 13 754323-100 Rev A ELECTRICAL INSTALLATION INSTRUCTIONS All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other applicable codes. ! WARNING: When using electrical products, basic precautions should always be observed, including the following: 1. DANGER: RISK OF ELECTRIC SHOCK! Connect only to a circuit protected by a ground-fault circuit interrupter. 2. Grounding is required. The unit should be installed by a licensed electrician and grounded. 3. Permit access for servicing motor as noted. 4. All building materials and wiring should be routed away from the pump body and heater (if equipped). “WHIRLPOOL WITH 2 LIGHTS” CONFIGURATION “AIR BATH” CONFIGURATION WHIRLPOOL TEE HEATER W H IR L P OO L HE AT E R 1 2 0 V @ 1 3 A M AX A IR B L O W E R 120V @ 10A MAX 2 LIGHTS 120V @ 1A W HIRLP OOL P UM P 120V @ 15A MAX P OW E R D IS T R IB U T ION BOX GND. 20A GFCI OUTLET 20A GFCI OUTLET BLACK WHITE WHITE G ND. 120 VAC BLACK 120 VAC BLACK WHITE 1 2 0 V AC GND. 15A GFCI OUTLET FIGURE 2: ELECTRICAL INSTALLATION DIAGRAM This installation requires 3 separate 120VAC dedicated circuits with GFCI (Ground Fault Circuit Interrupter) protection as shown in Figure 2. Two of the three GFCI outlets MUST be 20AMP service. At initial start-up with the power ON, push the GFCI test button. The reset button should pop out. Push this button in to reset. If the GFCI fails to operate in the manner, there is a ground fault or malfunction, indicating the possibility of electrical shock. Turn off the power and do not use until the source of the problem has been identified and corrected. 754323-100 Rev A 14 ELECTRICAL INSTALLATION INSTRUCTIONS (continued) (HEATER) Ensure the heater and pump are properly GROUNDED and BONDED as required. Attach the 8 AWG solid copper conductor supplied with the heater from the heater bonding lug to the motor frame bonding lug as shown in Figure 3. HEATER ON E-Z INSTALL™ The conductor is secured to the lugs using set screws. The motor frame shall have a second 8 AWG solid copper conductor connected from the frame bonding lug to the home’s electrical panel or approved local bonding point as shown in Figure 3. WHIRLPOOL HEATER (PUMP/MOTOR) RUN 8 AWG SOLID COPPER CONDUCTORS FROM HEATER BONDING LUG TO PUMP/MOTOR FRAME LUG AND FROM PUMP/MOTOR LUG TO APPROVED GROUND AS SHOWN FIRST COPPER CONDUCTOR SECOND COPPER CONDUCTOR PUMP/MOTOR FRAME WITH BONDING LUGS TO GROUND FIGURE 3: GROUNDING DIAGRAM WHIRLPOOL HEATER OPERATION WARNING: Prior to operation, review the Important Safety Instructions listed at the beginning of this instruction manual. Once the heater is installed and the whirlpool pump is operating, the heater is totally automatic. The heater will help maintain the temperature of the water in the bath. WHIRLPOOL E-Z INSTALL™ HEATER HEATER “ON” LIGHT Pressure Switch FACTORY INSTALLED - NOT FOR RESALE HEATER P/N: 753174-100 The heater is equipped with a preset pressure switch. The pump must be running with water flowing in the whirlpool to allow the heater to turn on. Bonding Lug on Heater Housing FIGURE 4: WHIRLPOOL HEATER INDICATOR LIGHT Indicator Light This light turns on whenever the heater is operating. High-Limit Switch The heater includes an exclusive "Intelligent High-Limit". This safety circuit will not "false trip" from hot tap water. It will only turn the heater off if the thermostat fails. If the high-limit trips frequently, call a service technician. To manually reset the circuit in the event that the “High-Limit” switch has been activated, simply (1) Turn off the whirlpool pump. (2) Drain water from the tub. (3) Remove power from heater by unplugging at receptacle or turning off circuit breaker. (4) The heater circuit will automatically reset in less than 15 minutes. (5) Restore power to the heater. (6) Whirlpool bath is now ready to use. 15 754323-100 Rev A UNDER DECK MOUNTING INSTRUCTIONS Please note that care must be taken to protect the surface of the tub during all aspects of the installation. Do not drill or cut the bath deck with the tub directly beneath it as damage to the tub may result. 1. 2. 3. 4. 5. 6. 7. 8. Install the tub per the installation instructions provided with the unit. Prepare the bath deck support structure per the local codes. Note - the bath deck must be self supporting. Cut bath deck to your specifications. Place the bath deck in position and trace the opening on the tub with a soft pencil. Do not drill or cut the bath deck with the tub directly beneath it as damage to the tub may result. Remove the bath deck and apply a generous bead of waterproof sealant on the outer edge of the traced line. Replace the bath deck and secure it into place. Apply additional sealant along the tub and bath deck interface as necessary to ensure a watertight seal. Remove excess sealant per the manufacturer's instructions. Finished bath deck surface material must be self-supporting and secured per local codes Waterproof Sealant Bath deck support material Bathtub Tub support structure per installation instructions provided with the tub AIR BATH DRAIN ILLUSTRATION DRAIN CONNECTION AND SYSTEM TEST (before installing bath into framed out structure) With supplied cable drain assembled to bath, connect drain outlet to waste line in accordance with the drain assembly instructions. Tighten all drain joints securely. Check the couplings and make sure they are hand-tight. Clean the air bath and fill with water to a point 2" below the overflow. Recheck the couplings and make certain that they are not leaking. (Although the couplings are factory tightened and inspected, some loosening may have occurred during transit.) Make sure the air bath is connected to the electrical supply and turn the air bath on. Check for leaks around all piping connections while the air bath is running. DRAIN STOPPER WITH ADJUSTABLE BOLT METAL STRAINER BOLT METAL STRAINER OVERFLOW ASSEMBLY CLOSE FLAT RUBBER GASKET OPEN DRAIN WASTE FLANGE PLASTIC DRAIN BASE WEDGE GASKET VERTICAL DRAIN PIPE OVERFLOW ESCUTCHEON OVERFLOW ASSEMBLY SET SCREW DRAIN ACTUATOR SHAFT OVERFLOW RETAINER OVERFLOW NUT WITH O-RING AIR BATH NUT WITH WASHER AND GASKET 90˚ ELBOW 754323-100 Rev A HORIZONTAL DRAIN PIPE 16 PLASTIC DRAIN BASE %3"*/$0//&$5*0/ 3FNPWFBOEJEFOUJGZBMMESBJODPNQPOFOUTBTEFGJOFEJOBJSCBUIESBJOJMMVTUSBUJPO 'JOETDIFEVMF17$QJQFMFOHUI)03*;0/5"-%3"*/1*1& $VUQJQFUPOPNJOBMMFOHUIBOENBSLBTiIPSJ[POUBMQJQFuESBJOUPFMCPXTFDUJPO 'JOEEJBNFUFS7&35*$"-'-&91*1&.BSLBTiWFSUJDBMQJQFu ESBJOUPFMCPXTFDUJPO *OTUBMMESBJOGSPNCFMPXVOJUUISPVHIPQFOJOHBTTIPXOJOQIPUP" " "QQMZPSQFBTJ[FEEBCTPGTJMJDPOFTFBMBOUUPCPUUPNXBTUFESBJOGMBOHFBOEQSFTTGMBUSVCCFSHBTLFUJOUPQMBDF BTTIPXOJOQIPUPT#BOE$ # $ "QQMZDPOUJOVPVTCFBEPGTJMJDPOFTFBMBOUUPGMBUSVCCFSHBTLFUBTTIPXOJOQIPUP%4FUBTJEFBOECFTVSFOPUUP EJTUVSCTJMJDPOFCFBE % "QQMZDPOUJOVPVTCFBEPGTJMJDPOFTFBMBOUUPCBDLTJEFUPNFUBMTUSBJOFSBTTIPXOJOQIPUP&1SFTT 4USBJOFSSFUBJOJOHCPMUJOUPNFUBMTUSBJOFSBOEJOTFSUJOUPESBJOIPMFPGBDSZMJDCBUI & 17 754323-100 Rev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ev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ev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ev A 20 1045*/45"--"5*0/$-&"/61 3FNPWFBMMDPOTUSVDUJPOEFCSJTGSPNCBUI5JMFHSPVUDBOCFSFNPWFEXJUIBXPPEFOQPQTJDMFTUJDLPSUPOHVFEFQSFTTPS %POPUVTFXJSFCSVTIFTPSBOZPUIFSNFUBMJNQMFNFOUPOCBUITVSGBDF 1PTUJOTUBMMBUJPODMFBOVQHFOFSBMMZDBOCFDPNQMFUFEVTJOHXBSNXBUFSBOEMJRVJEEJTIXBTIJOHEFUFSHFOU 4UVCCPSOEJSUPSTUBJOTNBZCFSFNPWFEVTJOHHSBOVMBS4QJDBOE4QBO¡NJYFEXJUIXBUFS 1BJOUFShTOBQIUIBDBOCFVTFEUPSFNPWFFYDFTTBEIFTJWFTBOEPSXFUPJMCBTFQBJOU "'5&3$"3&BOE$-&"/*/( r5IFIJHIHMPTTTVSGBDFJTSFTJTUBOUUPJNQBDUBOEDIFNJDBMTBOEXJMMSFUBJOJUTMBTUJOHMVTUFSXJUIQSPQFSDBSFBOENBJOUFOBODF r"MXBZTGJMMUIFUVCXJUIUFNQFSBUFXBUFS&YDFTTJWFMZIPUXBUFSNBZDBVTFTVSGBDFEBNBHF r$MFBOBGUFSVTFXJUIBNJMEMJRVJEIPVTFIPMEEFUFSHFOUDMFBOFS%POPUVTF-FTUPJM-ZTPM%JTJOGFDUBOUTQSBZPSDPODFOUSBUF PS-ZTPM#BTJO5VCBOE5JMF$MFBOFS8JOEFY.S$MFBO%PX%JTJOGFDUBOU#BUISPPN$MFBOFSPSDMFBOJOHQSPEVDUTJO BFSPTPMDBOT )"34)$)&.*$"-44)06-%/&7&3#&64&%0/"$3:-*$463'"$&4 r%POPUVTFXJSFCSVTIFTLOJWFTPSTIBSQPCKFDUTUPSFNPWFTUBJOTDJHBSFUUFUBSEFQPTJUTPSPUIFSTVSGBDFCMFNJTIFT r"CSBTJWFDMFBOFSTPSQPXEFSTNVTUOPUCFVTFETJODFUIFZXJMMEVMMUIFTVSGBDF*GUIFHMPTTZTVSGBDFMPPTFTJUTTIFFOEVMMFE BSFBTDBOCFSFTUPSFECZSVCCJOHXJUIBXIJUFiBVUPNPUJWFUZQFuQPMJTIJOHDPNQPVOEBOEXBYJOHXJUIBiMJRVJEXBYu r%POPUXBYBSFBTXIFSFZPVXBMLPSTUBOE r%POPUBMMPXOBJMQPMJTISFNPWFSBDFUPOFESZDMFBOJOHGMVJEQBJOUSFNPWFSPSPUIFSTPMWFOUTUPDPNFJOUPDPOUBDUXJUI UIFTVSGBDF r$MFBOUIFTVSSPVOEJOHTVSGBDFJNNFEJBUFMZBGUFSVTJOHDBVTUJDESBJODMFBOFST r#VSOJOHDJHBSFUUFTXJMMEBNBHFUIFTVSGBDF r4IPVMEEBNBHFUPUIFGJYUVSFPDDVSSFQBJSTDBOCFNBEFRVJDLMZBOEFBTJMZ :PVSEJTUSJCVUPSPSCVJMEFSDBOQSPWJEFEFUBJMT r%POPUQFSNJUESBJODMFBOFSUPFOUFSUIFDJSDVMBUJPOTZTUFN 21 754323-100 Rev A 3&.05&#-08&3-0$"5*0/015*0/ *.1035"/5*UJTOPUOFDFTTBSZUIBUUIFCMPXFSNPUPSCFSFMPDBUFE5IJTPQUJPOJTQSPWJEFEGPSUIFDBTFUIBUBQBSUJDVMBS JOTUBMMBUJPONBLFTUIJTFGGPSUQSBDUJDBM /05&3FMPDBUJOHCMPXFSNPUPSGSPNGBDUPSZJOTUBMMFEMPDBUJPOTFFQIPUPXJMMSFRVJSFEJTBTTFNCMZPGBJSCMPXFSGSPNNPVOUJOH CPBSE,FFQBMMIBSEXBSFGPSSFBUUBDINFOUBUOFXMPDBUJPO"EEJUJPOBMIBSEXBSFXJMMCFSFRVJSFEEFQFOEJOHVQPOGJOBMEFTJSFE QPTJUJPOPGBJSCMPXFS'PMMPXBMMJOTUSVDUJPOTMJTUFECFMPX 5:1*$"-7*&8 /05&*OTUBMMJOHUIFCMPXFSJOBSFNPUFMPDBUJPOXJMMSFEVDFUIFTZTUFNFGGJDJFODZ /05&3FMPDBUJOHBCMPXFSNPUPSTUJMMSFRVJSFTBTFSWJDFBDDFTTGPSUIFCMPXFS /05&"MMNBUFSJBMTOFFEFEGPSUIFSFMPDBUJPONVTUCFTVQQMJFECZUIFJOTUBMMFS5IJTJODMVEFTPSEFSJOHBMPOHFSDPOUSPMQBOFMDBCMF 1/" "TFQBSBUFDJSDVJUXIJDINVTUCFQSPUFDUFECZUIF(SPVOE'BVMU$JSDVJU*OUFSSVQUFS('$* JTSFRVJSFEJOUIFSFNPUFMPDBUJPO &MFDUSJDBMDPOOFDUJPOTTIPVMECFQFSGPSNFECZBMJDFOTFEFMFDUSJDJBO $IPPTFBTQBDFBTDMPTFUPUIFCBUIBTQPTTJCMFTPUIFTZTUFNXPSLTBTFGGJDJFOUMZBTQPTTJCMF5IFTQBDFNVTUCFBUMFBTUDVCJD GFFUBOEUIFCMPXFSNVTUCFNPVOUFEBUMFBTUJODIFTBCPWFUIFGMPPSBOEJODIFTNJOJNVNBXBZGSPNBOZXBMM5IFCMPXFSNVTU /05CFJOTUBMMFEJOBOBUUJDBSFB 5IFCMPXFSNPUPSNVTUCFMPDBUFEXJUIJOGFFUPGSJHJEQJQJOHGSPNUIFCBUIBJSNBOJGPME5IJTMJNJUBUJPOJTGPSUIFUPUBMQJQFMFOHUI BOEBQQMJFTUPBOZEJSFDUJPODIBOHFTBOEFMCPXT5IFSFDBOCFOPNPSFUIBOTJYDIBOHFTPGEJSFDUJPO5IFSFTIPVMECFBTGFX EJSFDUJPODIBOHFTBTQPTTJCMFBOEUIFQJQJOHJOTUBMMBUJPONVTUNFFUBMMSFRVJSFNFOUTPGMPDBMQMVNCJOHBOECVJMEJOHDPEFT %JTDPOOFDUUIFCMPXFSGSPNUIFGMFYJCMFIPTFBTTIPXOJOQIPUP%P/05SFNPWFUIFDIFDLWBMWFNBOJGPMEUIBUJTNPVOUFEUPUIF VOEFSTJEFPGUIFBJSCBUI5IFNBOJGPME.645SFNBJONPVOUFEBCPWFUIFUVCPWFSGMPXMFWFMBTTIPXOJO %P/05NPWFDIFDL WBMWFNBOJGPME 5:1*$"-7*&8 6TFu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ev A 22 AS AMERICA, INC. LIMITED LIFETIME WARRANTY FOR LUXURY ACRYLIC WHIRLPOOLS AS America, Inc. (“American Standard”) warrants to the original consumer purchaser that it will, at its option, repair or replace this whirlpool or any of its parts that are found by American Standard, in its sole judgment, to be defective under normal residential use and maintenance so long as it is owned by the original consumer purchaser. This warranty shall only become effective upon receipt by American Standard of a Warranty Registration evidencing proof of purchase. This limited warranty does not apply to commercial installations. The warranty for commercial installations is three (3) years. THIS WARRANTY SHALL BE VOID IF THE ACCESS PANEL TO THE WHIRLPOOL IS COVERED IN ANY MANNER CONTRARY TO THE INSTALLATION INSTRUCTIONS. In no event will American Standard be liable for the cost of repair or replacement of any installation materials including but not limited to tiles, marble etc. This limited warranty DOES NOT COVER the following: 1. Defects or damages arising from shipping, installation, alterations, accidents, abuse, misuse, lack of proper maintenance and cleaning as directed in the owner’s manual and use of other than genuine American Standard replacement parts, in all cases whether caused by a plumbing contractor, service company, the owner or any other person. 2. Deterioration through normal wear and tear and the expense of normal maintenance. 3. Commercial application. 4. Options and accessories. American Standard’s limited warranty on these items is one year for parts only and excludes labor. This one year limited warranty covers accessories manufactured by American Standard (e.g. aprons, drains, grab bars, heaters, trim kits) against defects of material or workmanship. Warranty coverage begins on the date the accessory was originally purchased by the owner. 5. Postage or shipping costs for returning products for repairs or replacement under this limited warranty and labor or other costs incurred in connection with product removal or installation under this limited warranty. 6. ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, ALL OF WHICH ARE HEREBY EXPRESSLY DISCLAIMED, OR THE EXTENSION BEYOND THE DURATION OF THIS LIMITED WARRANTY OF ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY OR FITNESS FOR AN INTENDED PURPOSE. (Some jurisdictions do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you.) 7. Responsibility for compliance with local code requirements. (Since local code requirements vary greatly distributors, retailers, dealers, installation contractors and users of plumbing products should determine whether there are any code restrictions on the installation or use of a specific product.) This limited warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case this limited warranty does not affect such statutory rights. For service under this warranty, you should contact the following: In the United States: American Standard Brands P.O. Box 659 West Caldwell, NJ 07007 Attention: Whirlpool Customer Care Center For residents of the United States, warranty information may be obtained by calling the following toll free number: (800) 442-1902 In Canada: AS Canada ULC 2480 Stanfield Road Missassauga, Ontario Canada L4Y 1S2 Toll free: (800) 387-0369 www.americanstandard.ca In Mexico: Customer Service Manager AS Maquila, S.A. de C.V. Via Morelos #330 Col. Santa Clara Ecatepec 55540 Edo. Mexico www.americanstandard.com.mx www.americanstandard-us.com To register your product on-line, visit http://www.americanstandard-us.com/warranty If you do not have access to a computer, please call us at 1-800-442-1902 and we’ll register you on-line. 23 754323-100 Rev A
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement