Ameriphone 30 Telephone User Manual

®
©AMERIPHONE products are manufactured by Walker, A Division of Plantronics, Inc.
12082 Western Avenue, Garden Grove, CA 92841
(800) 874-3005 VOICE • (800) 772-2889 TTY/TDD • (714) 897-4703 FAX
email: ameriphonecs@plantronics.com website: www.ameriphone.com
®
XL
E
N
G
L
I
S
H
The Extra Loud & Clear
XL-30 AMPLIFIED TELEPHONE
(Line Powered)
F
R
A
N
Ç
A
I
S
Users’ Guide
M03699 XL-30
XL-30LP 5270-3321
∆
A
4/03
Important Safety
IMPORTANT INSTRUCTIONS
Instructions
When using your telephone
equipment, basic safety precautions
should always be followed to
reduce the risk of fire, electric
shock and persons including the
following:
1.Read and understand all
instructions.
2.Follow all warnings and
instructions marked on the
telephone.
3.Do not use this telephone
near a bathtub, wash basin,
kitchen sink or laundry tub, in
a wet basement, near a
swimming pool or anywhere
else there is water.
4.Avoid using a telephone
(other than a cordless type)
during a storm. There may be
a remote risk of electrical
shock from lightning.
5.Do not use the telephone to
report a gas leak in the
vicinity of the leak.
6.Unplug this telephone from
the wall outlets before
cleaning. Do not use liquid
cleaners or aerosol cleaners
on the telephone. Use a damp
cloth for cleaning.
7.Place this telephone on a
stable surface. Serious damage
and/or injury may result if the
telephone falls.
8.Do not cover the slots and
openings on this telephone.
This telephone should never
be placed near or over a
radiator or heat register. This
telephone should not be
placed in a built-in installation
unless proper ventilation is
provided.
9.Operate this telephone using
the electrical voltage as
stated on the base unit or the
owner’s manual. If you are
not sure of the voltage in your
home, consult your dealer or
local power company.
10. Do not place anything on
the power cord. Install the
telephone where no one will
step or trip on the cord.
11. Do not overload wall outlets
or extension cords as this
can increase the risk of fire or
electrical shock.
12. Never push any objects
through the slots in the
telephone. They can touch
dangerous voltage points or
short out parts that could
result in a risk of fire or
electrical shock. Never spill
liquid of any kind on the
telephone.
13. To reduce the risk of electrical
shock, do not take this phone
Important Safety
Instructions
apart. Opening or removing
covers may expose you to
dangerous voltages or other
risks. Incorrect reassembly
can cause electric shock when
the appliance is subsequently
used.
14. Unplug this product from the
wall outlets and refer
servicing to the manufacturer
under the following conditions:
A. When the power supply
cord or plug is frayed or
damaged.
B. If liquid has been spilled
into the product.
C. If the telephone has been
exposed to rain or water.
D. If the telephone does not
operate normally by
following the operating
instructions. Adjust only
those controls that are
covered by the operating
instructions. Improper
adjustment may require
extensive work by a
qualified technician to
restore the telephone to
normal operation.
E. If the telephone has been
dropped or the case has
been damaged.
F. If the telephone exhibits a
distinct change in performance.
15. Never install telephone
wiring during a lightning
storm.
16. Never install telephone
jacks in wet locations
unless the jack is specifically
designed for wet locations.
17. Never touch uninsulated
telephone wires or terminals
unless the telephone line
has been disconnected at
the network interface.
18. Use caution when installing
or modifying telephone lines.
19. Use only the power cord
and batteries indicated in
this manual. Do not dispose
of batteries in a fire. They
may explode. Check with
local codes for possible
special disposal instructions.
ADDITIONAL SAFETY NOTES
FOR CANADIAN USERS
The following items are included
as part of the CS-03 Requirements.
The standard connecting
arrangement for the equipment is
CA11A. This product meets the
applicable Industry Canada
technical specifications.
NOTICE: The Canadian
Department of Communications
E
N
G
L
I
S
H
Important Safety
Instructions
label identifies certified equipment.
This certification means that the
equipment meets certain
telecommunications network
protective operational and safety
requirements. The Department
does not guarantee that the
equipment will operate to the
user’s satisfaction. Before installing
this equipment, users should
ensure that it is permissible to be
connected to the facilities of the
local telecommunications company.
The equipment must also be
installed using an acceptable
method of connection. In some
cases, the company’s inside
wiring associated with a single
line individual service may be
extended by means of a certified
connector assembly (telephone
extension cord). The customer
should be aware that compliance
with the above conditions may not
prevent degradation of service in
some situations. Repairs to certified
equipment should be made by an
authorized Canadian maintenance
facility designated by the supplier.
Any repairs or alterations made
by the user to this equipment, or
equipment malfunctions, may give
the telecommunications company
cause to request the user disconnect
the equipment.
Users should ensure for their own
protection that the electrical
ground connections of the power
utility, telephone lines and internal
metallic water pipe system, if
present, are connected together.
This precaution may be particularly
important in rural areas.
CAUTION: Users should not
attempt to make such connections
themselves, but should contact the
appropriate electric inspection
authority, or electrician, as
appropriate. The Ringer Equivalent
Number is an indication of the
maximum number of terminals
allowed to be connected to a
telephone interface. The
termination on an interface may
consist of any combination of
devices subject only to the
requirement that the sum of the
Ringer Equivalent Number of all
the devices not exceed five.
SAVE THESE INSTRUCTIONS
Contents
Introducing the XL-30
Warranty Service ..............................................................................1
Sales Receipt ....................................................................................1
Help from Ameriphone ......................................................................1
Package checklist ..............................................................................2
Features ..........................................................................................3
Setting up Your XL-30
Installing the Backup Batteries ............................................................4
Setting the Dialing Mode ..................................................................4
Connecting for Desk or Wall Mount ..................................................4
Desktop Use ..............................................................................4
For Wall Mounting ......................................................................5
Using Your XL-30
Incoming Voice Volume ......................................................................6
Incoming Voice Tone..........................................................................7
Ringer Volume and Pitch ....................................................................7
Hold ................................................................................................8
Last Number Redial ..........................................................................8
Flash................................................................................................8
Special Features
Programming the Memory Buttons ......................................................9
Direct Audio Output ........................................................................10
Outgoing Voice Amplification ............................................................10
Cochlear Implant Adapter Cord ........................................................10
Connecting to Speech Processor ......................................................11
Troubleshooting Chart ......................................................................12
Regulatory Compliance ....................................................................13
Warranty ........................................................................................19
Specifications ..................................................................................21
Index ..............................................................................................22
E
N
G
L
I
S
H
Introducing the XL-30
Thank you for selecting the XL-30
Amplified Telephone from
Ameriphone. These Operating
Instructions and the associated
Quick Operating Guide provide
you with the information you
need to use your XL-30 effectively
and safely. Read this manual
thoroughly before using your
telephone. Keep the manual near
the telephone for easy reference.
Warranty Service
Your telephone is designed to
provide years of quality service.
But, should the phone malfunction
and the Trouble-shooting Chart
on page 12 not resolve the
problem, follow the Warranty
procedure on page 19.
Sales Receipt
Be sure to save your sales receipt
as proof of purchase date should
you need warranty service.
1
Help from Ameriphone
For help with using your XL-30, call
our Customer Relations department
at 800-874-3005.
Please make sure your XL-30
package includes the items shown
in Figure 1.
E
N
G
L
I
S
H
Package Checklist
M1
M7
M2
M8
M3
M9
M4
M10
M5
M11
M6
¤
1
G
H
I
4
7
Q
R
PS
*
HOLD
2
A
B
C
5
8
D
E
F
J
K
L
3
6
T
U
V
9
X
Y
M
N
O
WZ
0
PROG
#
FLASH
REDIAL
AMPLIFY
TONE
VOL
LO
HI
Handset
Base Unit
Telephone Line Cords
XL-30
OPERATING
INSTRUCTIONS
AND
QUICK GUIDE
Handset
Coil Cord
Mounting Bracket
Figure 1 - Package Components
Operating Guides
2
Features on the XL-30
PULSE/TONE switch
AUDIO OUTPUT jack
DIAL
RINGER
P
Off Lo Hi
T
RING TONE
Lo
Hi
Phone line connection
AUDIO
OUTPUT
RING TONE switch
RINGER volume switch
M1
M7
M2
M8
M3
M9
M4
M10
M5
M11
Phone number
directory
MEMORY button
M6
¤
2
A
B
C
4
7
5
8
*
0
1
G
H
I
Q
R
PS
HOLD
D
E
F
J
K
L
3
6
T
U
V
9
X
Y
PROG
M
N
O
WZ
#
FLASH
REDIAL
REDIAL button
FLASH button
AMPLIFY
TONE
VOL
LO
HOLD
button TONE
slider
3
HOLD
indicator
Figure 2 - Base Unit Controls
HI
VOL volume slider
LOW BATTERY indicator
RING flasher
AMPLIFY button
AMPLIFY indicator
PROG program button
E
N
G
L
I
S
H
Setting up Your XL-30
There are five steps involved in
setting up your XL-30.
• Insert one 9 Volt alkaline
battery for extra bright ring
flasher (optional).
• Decide if you want the phone
to sit on a desk or hang on the
wall.
• Connect the telephone
components.
• Program up to to 12 telephone
numbers to call with the press
of a memory button.
• Set up special features
To install new battery:
1. Slide open the battery
compartment cover on the
bottom of the telephone,
(Figure 3).
2. Install one fresh battery, and
reinstall the cover.
Setting the Dialing Mode
Set the dial mode switch to T (tone) if
you have touch tone service. Set the
switch to P (pulse) if you have rotary
dialing.
Installing the Backup Batteries
To add extra brightness to the
XL-30’s ring flasher when you
receive calls, install one 9 Volt
alkaline battery (not included).
Insert 9V
battery
here
Press in
here
to open
battery
compartment
Figure 3 - Accessing the Battery
Connecting for Desk or Wall Mount
Desktop Use
1. Connect the telephone line
cord and the handset cord to
the telephone as shown in
Figure 4.
2. Lift the handset and listen for
a dial tone.
The phone is ready to use.
4
Setting up Your XL-30
(continued)
lower position of the base as
shown in Figure 6. Push the
mounting bracket in and
down firmly until it snaps into
place.
Line cord
handset
(curly) cord
Figure 4 - Connecting the Components
MANU
AUTO
For Wall Mounting
1. Pull the handset hook out as
shown in Figure 5 and
reverse its position so that the
hook points up and will hold
the handset when you hang
up.
AL
Figure 6 - Mounting Bracket for Wall
Mounting
3. Locate a desired wall phone
jack and hold phone upright.
4. Plug in the short phone line
cord and mount the phone
as shown in Figure 7.
Short phone
line cord
Figure 5 - Reversing the Hook
2. Insert the tabs of the phone
base into the slots in the
5
MANUAL
AUTO
Figure 7 - Wall mounting installation
Setting up Your XL-30
(continued)
5. Angle the phone downward
to feel for the LOWER
protruding nail head. Insert
the WALL JACK'S nail head
into the LOWER part of the
phone's mounting bracket.
6. Once the lower nail head
has been inserted, insert the
UPPER nail head into the
phone's bracket and slide
the phone down until it is
firmly in place on the wall.
7. Once firmly in place, attach
the short line cord to the
phone and attach the
phone's handset.
8. Lift the handset and listen for
a dial tone. The phone is
now ready to use.
E
N
G
L
I
S
H
Using Your XL-30
Incoming Voice Volume
You can adjust the volume of
incoming calls by simply sliding
the VOL control. This gives you up
to 18 dB. more volume. If you
want more amplification, follow
the directions below.
1. Press the AMPLIFY button as
shown in Figure 8 to turn the
incoming voice amplifier ON or
OFF. When AMPLIFY is on,
the AMPLIFY indicator light
comes on.
HOLD
PROG
FLASH
REDIAL
AMPLIFY
TONE
VOL
LO
HI
Figure 8 - AMPLIFY Button and Indicator
2. Adjust the volume in the ear
piece by moving the VOL slide
control in Figure 9. With
AMPLIFY ON incoming
volume will be up to 30dB
louder.
HOLD
PROG
FLASH
REDIAL
AMPLIFY
VOL
TONE
LO
HI
Figure 9 - Volume Slide Control
6
Using Your XL-30
(Continued)
USE WITH
CAUTION
VOLUME
LOUD
CAUTION: Repeated incremental
exposure to amplification levels
greater than18 dB may be
harmful to individuals without
hearing disabilities. Therefore,
do not remove the warning
label attached to the back
of the handset. If it is likely that
a visually impaired person will use
the telephone, securely attach the
provided warning printed in
Braille to the back of the handset
(See, Diagram A).
Diagram A.
NOTE: In standard use, the
amplifier turns off whenever you
hang up the telephone. This is a
useful feature if many people use
the phone. If you want the
amplifier to always remain on,
slide the Volume Reset Override
switch on the bottom of the phone
to ON, as shown in Figure 10.
7
- OFF
MANUAL
AUTO
- ON
Volume
Reset
Override
Figure 10 - Volume Reset Override On/Off
Incoming Voice Tone
The XL-30 provides extra
amplification at the sound
frequency you need to boost. To
identify the sound frequency range
that best suits your needs, follow
these steps:
1. When you hear a voice on the
line, press the AMPLIFY button
shown in Figure 8.
2. Adjust the TONE slide control in
Figure 11 to suit your hearing.
*
HOLD
0
PROG
FLASH
REDIAL
AMPLIFY
TONE
LO
#
VOL
HI
Figure 11 - Tone Slide Control
E
N
G
L
I
S
H
Using Your XL-30
(Continued)
Ringer Volume and Pitch
HOLD
PROG
FLASH
REDIAL
AMPLIFY
1. You can adjust the RINGER
VOLUME as high as 85+
decibels. The settings available
are OFF, LO and HI as shown in
Figure 12.
TONE
VOL
LO
HI
Figure 13 - Hold Button and Indicator
Last Number Redial
DIAL
RINGER
P
Off Lo Hi
T
RING TONE
Lo
Hi
AUDIO
OUTPUT
Figure 12 - Ringer Volume & Pitch
To redial the last number called,
lift the handset and press
REDIAL. The phone will redial up
to 31 digits.
0
HOLD
2. The RING TONE has two pitch
settings: LO and HI.
Hold
To put the line on hold, press the
HOLD button and return the handset
to its cradle. You will notice the HOLD
indicator light comes on.
NOTE: If you pick up an extension
phone on the same line when the
XL-30 is on HOLD, the XL-30 will
release the HOLD and you can
continue your conversation on the
extension phone.
E
PROG
FLASH
REDIAL
AMPLIFY
TONE
VOL
LO
HI
Figure 14 - Redial Button
Flash
Press the FLASH button shown in
Figure 15 to access special
services available from your local
phone company such as Call
Waiting and 3-Way Calling.
HOLD
FLASH
PROG
REDIAL
AMPLIFY
TONE
VOL
LO
HI
Figure 15 - Flash Button
8
Special Features
Programming the Memory Buttons
You can automatically dial twelve
programmed telephone numbers
using the memory buttons shown in
Figure 16. Each button can be
programmed (or reprogrammed
using the same procedure) for a
phone number up to 15 digits
long.
2. Enter the phone number on the
keypad (Figure 18) just as you
would dial it normally.
Note: Press REDIAL if you want
to insert a brief pause between
two numbers.
DIALOGUE XL 40
1
4
7
G
H
I
Q
R
PS
M3
M9
M4
M10
M5
M11
2
3
D
E
F
Figure 16 - Memory Buttons
1. Lift the handset and press PROG
as shown in Figure 17.
*
HOLD
PROG
#
FLASH
REDIAL
AMPLIFY
TONE
VOL
LO
HI
Figure 17 - PROG Button
9
M
N
O
X
Y
WZ
O
P
E
4. Press a memory button (Figure 16)
to store this number on that button.
To program a button, follow these
steps:
0
T
U
V
D
E
F
3. Press PROG (Figure 17) once
again.
¤
1
J
K
L
3
6
9
#
*
Figure 18 - Telephone Keypad
M6
A
B
C
2
5
8
0
A
B
C
5. Immediately hang up the handset.
Note: Any number previously
stored at that button number will
be overwritten.
6. To change a stored number,
repeat the programming process
starting with step 1.
Note: Do not program 911 in any
memory button.
E
N
G
L
I
S
H
Special Features
(continued)
Direct Audio Output
The AUDIO OUTPUT socket allows
you to connect the XL-30 to a
hearing aid, neck loop, cochlear
implant or other assistive listening
devices.
DIAL
RINGER
T
Off Lo Hi
RING TONE
Lo
Hi
AUDIO
OUTPUT
Figure 19 - Audio Output Socket
To use this port, plug in a
compatible auxiliary cable and
connect it to your assistive
listening device. Speak into the
handset when you use the Audio
Output connection.
Outgoing Voice Amplification
The XL-30 can amplify your
outgoing voice by up to 15 dB. To
use this feature, set the outgoing
voice amplifier switch to AMPLIFY
(underneath the unit). Note: Even
with the AMPLIFY switch ON, the
voice of your callers can still be
amplified by up to 15dB.
Note: The factory pre-setting is
NORMAL.
Cochlear Implant Adapter Cord
A cochlear adapter cord is
available from Ameriphone that
can be used to directly connect
the XL-30 into a speech processor.
10
Special Features
(continued)
Connecting the Speech Processor:
Caution: Before plugging any cord
into your speech processor, you
must consult your implant
manufacturer.
• Plug the mono end of the plug
into the speech processor.
• Plug the stereo end of the plug
into the Audio Output socket on
the phone.
• Speak into the handset when
using the Cochlear Implant
Adapter Cord.
M7
M1
M8
M2
M3
M9
M4
M10
M5
M11
M6
¤
1
G
H
I
4
7
Q
R
PS
*
HOLD
2
A
B
C
5
8
T
U
V
J
K
L
3
6
D
E
F
9
X
Y
M
N
O
WZ
0
PROG
#
FLASH
REDIAL
AMPLIFY
TONE
VOL
LO
HI
WARNING! During thunderstorms,
avoid using telephones. Electric
shock from lightning can occur.
11
E
N
G
L
I
S
H
Troubleshooting Chart
The chart below will help you
solve most problems that may
arise during operation of your
telephone. Should the difficulty
continue, contact Ameriphone or
your authorized dealer for
assistance.
SYMPTOM
No dial tone
CAUSE AND
CORRECTIVE
ACTION
Check all phone
cord connections.
No number
dialed when
memory
button
pressed
No number stored
in that memory
button. See:
“Programming the
Memory buttons”,
P. 9.
Call cannot
be dialed,
or dials
very slowly
See “Setting Up
Your Phone” to
reset the dial
mode switch,
P. 4, 5.
Call comes in 1. Check that line
cord is not loose.
but phone
does not ring. 2. Check battery
Ring flasher
not very
bright
Check and replace
the 9 Volt battery
12
Regulatory Compliance
Part 68 of FCC Rules
Information
This equipment complies with Part
68 of the FCC rules and the
requirements adopted by the
ACTA. On the bottom of this
equipment is a label that contains,
among other information, a
product identifier in the format
US:AAAEQ##TXXXX. If requested,
this number must be provided to the
telephone company.
A plug and jack used to connect
this equipment to the premises
wiring and telephone network
must comply with the applicable
FCC Part 68 rules and requirements
adopted by the ACTA. A compliant
telephone cord and modular plug,
RJ11 USOC, is provided with this
product. It is designed to be
connected to a compatible modular
jack that is also compliant. See
installation instructions for details.
The REN is used to determine the
number of devices that may be
connected to a telephone line.
Excessive RENs on a telephone
13
line may result in the devices not
ringing in response to an incoming
call. In most but not all areas, the
sum of RENs should not exceed
five (5.0). To be certain of the
number of devices that may be
connected to a line, as determined
by the total RENs, contact the
local telephone company. For
products approved after July 23,
2001, the REN for this product is
part of the product identifier that
has the format US:AAAEQ##TXXXX.
The digits represented by ## are
the REN without a decimal point
(e.g., 03 is a REN of 0.3). For
earlier products, the REN is
separately shown on the label.
If this telephone equipment, the
XL-30 telephone, causes harm to
the telephone network, the
telephone company will notify you
in advance that temporary
discontinuance of service may be
required. But if advance notice
isn’t practical, the telephone
company will notify the customer
as soon as possible. Also, you will
be advised of your right to file a
complaint with the FCC if you
E
N
G
L
I
S
H
Regulatory Compliance
(continued)
believe it is necessary.
The telephone company may
make changes in its facilities,
equipment, operations or procedures
that could affect the operation of
the equipment. If this happens the
telephone company will provide
advance notice in order for you to
make necessary modifications to
maintain uninterrupted service.
If trouble is experienced with this
telephone equipment, for repair or
warranty information, please contact
Walker / Ameriphone, 1-800874-3005. If the equipment is
causing harm to the telephone
network, the telephone company
may request that you disconnect
the equipment until the problem is
resolved.
DO NOT DISASSEMBLE THIS
EQUIPMENT.
This telephone equipment is not
intended to be repaired and it
contains no repairable parts.
Opening the equipment or any
attempt to perform repairs will
void the warranty. For service or
repairs, call 1-800-874-3005.
Connection to party line service is
subject to state tariffs. Contact the
state public utility commission,
public service commission or
corporation commission for
information.
If your home has specially wired
alarm equipment connected to the
telephone line, ensure the
installation of this telephone
equipment does not disable your
alarm equipment. If you have
questions about what will disable
alarm equipment, consult your
telephone company or a qualified
installer.
This telephone equipment is
hearing aid compatible.
We recommend the installation of
an AC surge arrester in the AC
outlet to which this equipment is
connected. The telephone
companies report that electrical
surges, typically lighting transients,
are very destructive to customer
terminal equipment connected to
AC power sources.
14
Regulatory Compliance
(continued)
Customer-Owned Coin/Credit
Card Phones:
To comply with state tariffs, the
telephone company must be given
notification prior to connection. In
some states, the state public utility
commission, public service
commission or corporation
commission must give prior
approval of connection.
Part 15 of FCC Rules
Information
This device complies with part 15
of the FCC Rules. Operation is
subject to the following two
conditions: (1) This device may
not cause harmful interference,
and (2) this device must accept
any interference received,
including interference that may
cause undesired operation.
Your XL-30 Telephone has been
tested and found to comply with
the limits of a Class B digital
device, pursuant to Part 15 of
15
FCC rules. These limits are
designed to provide reasonable
protection against harmful
interference in residential installation.
This equipment generates, uses,
and can radiate radio frequency
energy and, if not installed and
used in accordance with the
instructions, may cause harmful
interference to radio communications.
However, there is no guarantee
that interference will not occur in
a particular installation; if this
equipment does cause harmful
interference to radio or television
reception, which can be determined
by turning the equipment off and
on, you are encouraged to try to
correct the interference by one of
the following measures:
1.Where it can be done safely,
reorient the receiving
television or radio antenna.
2.To the extent possible,
relocate the television, radio
or other receiver with respect
to the telephone equipment.
Regulatory Compliance
(continued)
(This increases the separation
between the telephone
equipment and the receiver.)
3.Connect the telephone
equipment into an outlet on a
circuit difference from that
to which the television, radio,
or other receiver is connected.
4.Consult the dealer or an
experienced radio/TV
technician for help.
CAUTION: Changes or
modifications not expressly
approved by the manufacturer
responsible for compliance could
void the user’s authority to operate
the equipment.
THE PARTY RESPONSIBLE
FOR PRODUCT COMPLIANCE
Ameriphone Products by Walker,
A Division of Plantronics, Inc.
12082 Western Avenue
Garden Grove, CA 92841
Telephone: 800-874-3005
Industry Canada Technical
Specifications
This product meets the applicable
Industry Canada technical
specifications.
E
N
G
L
I
S
H
Before installing this equipment,
users should ensure that it is
permissible to be connected to the
facilities of the local
telecommunications company. The
equipment must also be installed
using an acceptable method of
connection. In some cases, the
company’s inside wiring
associated with a single line
individual service may be
extended by means of a certified
connector assembly (telephone
extension cord). The customer
should be aware that compliance
with the above conditions may not
prevent degradation of service in
some situations.
Repairs to certified equipment
should be made by an authorized
Canadian maintenance facility
designated by the supplier. Any
repairs or alterations made by the
16
Regulatory Compliance
(continued)
user to this equipment, or
equipment malfunctions, may give
the telecommunications company
cause to request the user to
disconnect the equipment.
Users should ensure for their own
protection that the electrical
ground connections of the power
utility, telephone lines and internal
metallic water pipe system, if
present, are connected together.
This precaution may be particularly
important in rural areas.
Caution: Users should not attempt
to make such connections
themselves, but should contact the
appropriate electric inspection
authority, or electrician, as
appropriate.
The Ringer Equivalence Number is
an indication of the maximum
number of terminals allowed to be
connected to a telephone interface.
The termination on an interface
may consist of any combination of
devices subject only to the
requirement that the sum of the
Ringer Equivalence Numbers of all
17
the devices does not exceed five.
[The term “IC:” before the
certification/registration number
only signifies that the Industry
Canada technical specifications
were met.]
E
N
G
L
I
S
H
18
Warranty
This warranty applies only to
Ameriphone products that are
purchased and used in the United
States or Canada.
Ameriphone warrants the XL-30
telephone against any defect in
materials or workmanship for the
period of one year from the date
of purchase.
If your Ameriphone product is
defective and returned within 30
days of the date of purchase, your
Ameriphone dealer will replace it
at no charge.
If returned after 30 days but
within one year from the date of
purchase, we will repair or replace
it at no charge. In the repair of
your XL-30, we may use new or
reconditioned replacement parts. If
we elect to replace your XL-30, we
may replace it with a new or
reconditioned product of the same
or similar design. Repair or
replacement will be warranted for
either 90 days or the remaining
time on the original warranty
period, whichever is longer.
19
Implied warranties, including
those of fitness for a particular
purpose and merchantability (an
unwritten warranty that the
product is fit for ordinary use), are
limited to one year from date of
purchase. We will not pay for loss
of time, inconvenience, loss of use
of your XL-30 phone, or property
damage caused by your XL-30
phone or its failure to work, or
any other incidental or consequential
damages. Some states do not
allow limitations on how long an
implied warranty lasts or the
exclusion of incidental or
consequential damages, so the
above exclusions or limitations
may not apply to you.
To get warranty service for your
XL-30 phone, you must provide
proof of the purchase date. Within
30 days of the date of purchase,
return your XL-30 to the place
where you purchased it for
immediate replacement. After 30
days, call Ameriphone at (800)
874-3005 voice or 800-7722889 TTY for the authorized
service center nearest you. You
E
N
G
L
I
S
H
Warranty
must prepay all shipping costs.
systems.
We suggest you save the original
package materials in the event
you need to ship the XL-30. When
shipping for warranty repair,
include your name, address,
phone number, proof of date of
purchase, and a description of the
problem. After repairing the
product, we, (or the service
center) will ship it back to you at
no cost within the United States
and Canada. CANADIAN
RESIDENTS: call ameriphone at
800-874-3005, 800-772-2889
TTY for instructions.
If your XL-30 is not covered by this
warranty, call us at (800) 8743005 voice or (800) 772-2889
TTY for advice as to whether we
will repair your XL-30 and other
repair information. The repair
shall be warranted for 90 days.
This warranty does not cover
defects resulting from accidents,
damage while in transit to our
service location, alterations,
unauthorized repair, failure to
follow instructions, misuse, use
outside the United States or
Canada, fire, flood, and acts of
God. Nor do we warrant the
product to be compatible with any
particular telephone equipment,
party line, key telephone systems
or more sophisticated switching
20
Specifications
Maximum gain
High frequency (3kHz): 30dB
Wide band (300 to 3000Hz):
20dB
Tone control range
Full range: 300 to 3000Hz using
one slide control.
Dimensions
Size: 9 1/2" x 7" x 3 1/4"
Weight: 2.52 lbs.
Power Requirements
One 9 Volt alkaline battery for
ring flasher operation only (not
included)
21
E
N
G
L
I
S
H
Index
Connecting for Desk or Wall Mount
Desktop Use ......................4
Wall Mount ......................5
Connecting to
Speech Processor ............11
Direct Audio Output ..............10
Features ................................3
Flash ......................................8
Help from Ameriphone ............1
Hold ......................................8
Incoming Voice Tone ................7
Incoming Voice Volume ............6
Installing the Backup Batteries ..4
Last Number Redial ................8
Package Checklist ..................2
Programming the
Memory Buttons ................9
Ringer Volume and Pitch ..........8
Sales Receipt ........................1
Troubleshooting ....................12
Warranty Service ....................1
Ameriphone products are
manufactured by Walker,
A Division of Plantronics, Inc.
© 2002 Plantronics, Inc. All rights
reserved. Ameriphone, Amplifying
Your Life, and Walker are
trademarks or registered
trademarks of Plantronics, Inc.
22