AMX NXD-CV7 Car Video System User Manual

instruction manual
NXD-CV7 and NXT-CV7
7" Modero Widescreen Video Touch Panels
(Firmware version G4)
Tou c h Pa n els an d A cc e ss o r ie s
AMX Limited Warranty and Disclaimer
AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three
(3) years from the date of purchase from AMX Corporation, with the following exceptions:
•
Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch
overlay components that are warranted for a period of one (1) year.
•
Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one
(1) year.
•
AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting
products, as long as the AMX Lighting products are under warranty. AMX Corporation does guarantee the
control of dimmable loads that are properly connected to our lighting products. The dimming performance or
quality cannot be guaranteed due to the random combinations of dimmers, lamps and ballasts or transformers.
•
Unless otherwise specified, OEM and custom products are warranted for a period of one (1) year.
•
AMX Software is warranted for a period of ninety (90) days.
•
Batteries and incandescent lamps are not covered under the warranty.
This warranty extends only to products purchased directly from AMX Corporation or an Authorized AMX Dealer.
All products returned to AMX require a Return Material Authorization (RMA) number. The RMA number is
obtained from the AMX RMA Department. The RMA number must be clearly marked on the outside of each box.
The RMA is valid for a 30-day period. After the 30-day period the RMA will be cancelled. Any shipments received
not consistent with the RMA, or after the RMA is cancelled, will be refused. AMX is not responsible for products
returned without a valid RMA number.
AMX Corporation is not liable for any damages caused by its products or for the failure of its products to perform.
This includes any lost profits, lost savings, incidental damages, or consequential damages. AMX Corporation is not
liable for any claim made by a third party or by an AMX Dealer for a third party.
This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort
claim (including negligence and strict product liability), a contract claim, or any other claim. This limitation of
liability cannot be waived or amended by any person. This limitation of liability will be effective even if AMX
Corporation or an authorized representative of AMX Corporation has been advised of the possibility of any such
damages. This limitation of liability, however, will not apply to claims for personal injury.
Some states do not allow a limitation of how long an implied warranty last. Some states do not allow the limitation or
exclusion of incidental or consequential damages for consumer products. In such states, the limitation or exclusion of
the Limited Warranty may not apply. This Limited Warranty gives the owner specific legal rights. The owner may
also have other rights that vary from state to state. The owner is advised to consult applicable state laws for full
determination of rights.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX CORPORATION MAKES NO
OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX CORPORATION
EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY
IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS
LIMITED WARRANTY.
FCC Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received; including interference that may cause undesired operation.
Federal Communications Commission (FCC)
Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed an operated with a minimum
distance of 20 centimeters between the radiator and your body.
Table of Contents
Table of Contents
Introduction ...............................................................................................................1
CV7 Specifications ............................................................................................................ 3
CV7 Panels - Connector Layout........................................................................................ 6
CV7 Touch Panel Accessories ................................................................................7
NXA-AVB/ETHERNET Breakout Box (FG2254-10) .......................................................... 7
Product Specifications ............................................................................................................. 7
Installing the NXA-AVB/ETHERNET........................................................................................ 8
Wiring the NXA-AVB/ETHERNET connectors and cables....................................................... 9
Wiring the NXA-AVB/ETHERNET for Unbalanced Audio ...................................................... 10
Wiring the NXA-AVB/ETHERNET for Balanced Audio .......................................................... 11
Modero Table Top Cable (CA2250-50) ........................................................................... 11
Product Specifications ........................................................................................................... 12
Wiring information for the Modero Table Top cable ............................................................... 12
NXA-WC80211B/CF 802.11b Wireless Card (FG2255-03) ............................................ 14
Installation of the Wireless Card (Table Top Panel)............................................................... 15
Step 1: Removing the NXT Outer Housing ............................................................................ 15
Step 2: Upgrading internal components (Compact Flash and Wireless cards)...................... 17
Step 3: Closing and Securing the NXT Enclosure ................................................................. 18
Installation of the Wireless Card (WallMount Panel).............................................................. 19
Step 1: Removing the existing NXD Outer Housing............................................................... 19
Step 2: Installing the Upgrade Components (NXD) ............................................................... 20
Step 3: Replacing and Securing the NXD Enclosure ............................................................. 20
NXA-CFSP Compact Flash (2116-3x)............................................................................. 21
Installation Procedures for the Compact Flash Card (Table Top Panel)................................ 21
Installation Procedures for the Compact Flash Card (WallMount Panel)............................... 21
NXT-BP Power Pack (FG2255-10) ................................................................................. 21
NXA-BASE/1 Battery Base Kit (FG2255-05K) ................................................................ 22
Checking the NXT-BP charge ................................................................................................ 23
Installing an NXT-BP into the NXA-BASE/1........................................................................... 23
Installing the NXA-BASE/1 below an NXT-CV7 Panel........................................................... 24
Charging the NXT-BP using the NXA-BASE/1....................................................................... 25
NXT-CHG Battery Charger Kit (FG2255-50K) ................................................................ 25
Powering the NXT-CHG......................................................................................................... 26
Reading the NXT-CHG LED Indicator.................................................................................... 26
Charging the NXT-BP batteries using the NXT-CHG............................................................. 27
Recalibrating the batteries ..................................................................................................... 27
7" Modero Widescreen Touch Panels
i
Table of Contents
Installation .............................................................................................................. 29
Unpacking the Panel ....................................................................................................... 29
Installing the Internal Components.................................................................................. 29
Installing the No-Button Trim Ring .................................................................................. 29
Installing the Button Trim Ring ........................................................................................ 31
Pre-Wall Installation of the Conduit Box.......................................................................... 33
Installation of an NXD Touch Panel ................................................................................ 34
Installing the NXD panel within a Conduit Box....................................................................... 34
Installing the NXD into drywall using Expansion Clips ........................................................... 35
Installing the NXD into a Flat Surface using #4 screws ......................................................... 38
Installing an NXD-CV7 into an (optional) Rack Mount Kit (NXA-RK7) ................................... 40
Wiring Guidelines for the CV7 Panels............................................................................. 41
Preparing captive wires.......................................................................................................... 41
Using the PSN NetLinx connector for power.......................................................................... 41
Audio/Video RJ-45 Connections and Wiring ................................................................... 42
Ethernet 10/100 Base-T RJ-45 Connections and Wiring ................................................ 42
Connecting and Using USB Input Devices...................................................................... 43
Panel Calibration .................................................................................................... 45
Calibrating the Modero Panel.......................................................................................... 45
Testing your Calibration ......................................................................................................... 46
Configuring Communication ................................................................................. 47
Modero Setup and System Connection .......................................................................... 47
Configuring and Using USB with a Virtual Master........................................................... 49
Step 1: Setup the Panel and PC for USB Communication..................................................... 49
Step 2: Confirm the Installation of the USB Driver on the PC ................................................ 49
Step 3: Confirm and View the current AMX USB device connections ................................... 51
Step 4: Use the USB to Configure a Virtual Master (using NetLinx Studio)........................... 53
Step 5: Confirm and View the current AMX USB device connections ................................... 54
Secondary Connection Page - Wireless Access Overview............................................. 55
IP Routing .............................................................................................................................. 55
Hot Swapping......................................................................................................................... 55
Configuring a Wireless Network Access ......................................................................... 57
Step 1: Configure the Panel’s Wireless IP Settings ........................................................ 57
Wireless communication using a DHCP Address .................................................................. 57
Wireless communication using a Static IP Address ............................................................... 58
Step 2: Configure the Card’s Wireless Security Settings ................................................ 59
Configuring the Modero’s wireless card for unsecured access to a WAP200G..................... 59
Configuring the Modero’s wireless card for secured access to a WAP200G......................... 60
Configuring multiple wireless Moderos to communicate to a target WAP200G..................... 64
ii
7" Modero Widescreen Touch Panels
Table of Contents
Configuring a Wired Ethernet Connection....................................................................... 64
Step1: Configure the Panel’s Wired IP Settings.............................................................. 64
IP Settings section - Configuring a DHCP Address over Ethernet......................................... 64
IP Settings section - Configuring a Static IP Address over Ethernet...................................... 65
Step 2: Choose a Master Connection Mode Setting ....................................................... 66
Step 3: Configure an Ethernet Connection Type............................................................. 66
Master Connection section - Virtual Master communication over Ethernet ........................... 67
Master Connection section - NetLinx Master Ethernet IP Address - URL Mode.................... 69
Master Connection section - NetLinx Master Ethernet IP Address - Listen Mode ................. 70
Master Connection section - NetLinx Master Ethernet IP Address - Auto Mode ................... 71
Using G4 Web Control to Interact with a G4 Panel ......................................................... 71
Accessing the NetLinx Master via an IP Address............................................................ 73
Using your NetLinx Master to Control the G4 panel........................................................ 74
Upgrading Modero Firmware .................................................................................77
Upgrading the Modero Firmware via the USB port ......................................................... 77
Step 1: Configure the panel for a USB Connection Type....................................................... 77
Step 2: Prepare NetLinx Studio for communication via the USB port .................................... 78
Step 3: Confirm and Upgrade the firmware via the USB port ................................................ 79
Upgrading the Modero Firmware via Ethernet (IP Address) ........................................... 81
Step 1: Prepare the Master for communication via an IP....................................................... 81
Step 2: Prepare the panel for communication via an IP......................................................... 82
Step 3: Verify and Upgrade the panel firmware via an IP ...................................................... 83
Firmware Pages and Descriptions ........................................................................85
Setup Navigation Buttons................................................................................................ 85
Setup Page...................................................................................................................... 86
Project Information Page........................................................................................................ 88
Panel Information Page.......................................................................................................... 89
Time & Date Setup Page ....................................................................................................... 90
Volume Page.......................................................................................................................... 92
Supported sampling rates for WAV........................................................................................ 93
Protected Setup Page ............................................................................................................ 93
Video Adjustment Page.......................................................................................................... 93
Battery Base Page ................................................................................................................. 95
Protected Setup Navigation Buttons ............................................................................... 97
Protected Setup Page ..................................................................................................... 98
G4 Web Control Page .......................................................................................................... 100
Sensor Setup ....................................................................................................................... 101
Making the most of the Automated Brightness Control feature (DIM Mode)........................ 103
Password Setup Page.......................................................................................................... 104
7" Modero Widescreen Touch Panels
iii
Table of Contents
Calibration Page................................................................................................................... 105
Secondary Connection Page ............................................................................................... 105
System Connection Page..................................................................................................... 109
Programming ........................................................................................................ 113
Button Assignments ..................................................................................................... 113
Page Commands .......................................................................................................... 113
Programming Numbers ................................................................................................. 119
RGB triplets and names for basic 88 colors ........................................................................ 119
Font styles and ID numbers ................................................................................................. 121
Border styles and Programming numbers............................................................................ 122
"^" Button Commands ................................................................................................... 124
Text Effect Names......................................................................................................... 144
Button Query Commands.............................................................................................. 145
Panel Runtime Operations ............................................................................................ 154
Input Commands........................................................................................................... 158
Embedded codes .......................................................................................................... 159
Panel Setup Commands ............................................................................................... 160
Dynamic Image Commands.......................................................................................... 161
Troubleshooting ................................................................................................... 163
Appendix ............................................................................................................... 169
Text Formatting Codes for Bargraphs/Joysticks ........................................................... 169
Text Area Input Masking ............................................................................................... 170
Input mask character types .................................................................................................. 170
Input mask ranges................................................................................................................ 171
Input mask next field characters .......................................................................................... 171
Input mask operations.......................................................................................................... 171
Input mask literals ................................................................................................................ 171
Input mask output examples ................................................................................................ 172
URL Resources............................................................................................................. 173
Special escape sequences .................................................................................................. 173
iv
7" Modero Widescreen Touch Panels
Introduction
Introduction
The NXT/D-CV7 7" Modero Widescreen Color Video Touch Panels (FIG. 1) are the industry’s first
widescreen mini-touch panels and are available only through AMX.
NXD-CV7 (front view)
(FG2258-02)
NXT-CV7 (front view)
(FG2258-01)
FIG. 1 Sample 7" Video Touch Panels
These Color Video (CV) panels display NTSC/PAL/SECAM video formats within variable sized
windows. They include a built-in microphone, speakers, audio/headphone connector, and six
NetLinx programmable pushbuttons (available on NXD models only when mounted with included
Button Trim Ring).
Table Top models use AMX's exclusive SmoothTilt™ technology for effortless adjustment of the
viewing angle.
Each panel is sold only as part of a CV7 Kit which includes both a panel and an
NXA-AVB/ETHERNET Audio/Video Breakout Box (FG2254-10). This box facilitates the
installation and distribution of video (either Composite or S-Video), data (via Ethernet), and audio
to Modero touch panels located up to 200 feet (60.96 m) from the breakout box. CV7 panels are
ideally suited for displaying full motion video and audio with overlay graphics for applications with
demanding visual requirements.
CV7 7" Widescreen Video Touch Panel Kits
NXD-CV7
(FG2258-02K)
7" Widescreen Color Video Wall Mount Touch Panel Kit (with buttons)
(includes both an NXD panel and an NXA-AVB/ETHERNET A/V Breakout Box).
NXT-CV7
(FG2258-01K)
7" Widescreen Color Video Table Top Touch Panel Kit (without buttons)
(includes both an NXT panel and an NXA-AVB/ETHERNET A/V Breakout Box).
The NXD-CV7 panel (FG2258-02) is shipped, by default with a Trim Ring containing
buttons, but the end user can later install the included Trim Ring without button
openings.
NXT panels can not be upgraded by simply replacing a Trim Ring on the Faceplate.
7" Modero Widescreen Touch Panels
1
Introduction
Key features common to both panels include:
CV7 panels are based on the latest display technology and support AMX's 4th generation
(G4) graphics which provide higher brightness, richer colors, and deeper contrast. The
new G4 graphics technology is supported by the latest AMX TPDesign4 Touch Panel
Design program (version 2.5 or higher).
CV7 panels display eye-catching images and full-motion video on a large 16:9 image
format, while providing a wide 100-degree top-to-bottom viewing angle.
CV7 panels feature a front panel light sensor, motion sensor, IR receiver and a
Sleep/Setup Access combo button.
CV7 panels support AMX Computer Control, which enables remote viewing and control
of any networked computer directly from the panel. This gives the user the ability to
launch digital music from a PC, cruise the Internet, check and respond to
E-mail, open software files, and launch applications. Anything you can do on your PC
can be accomplished through these panels.
The optional wireless solution includes an NXA-WC80211B/CF internal wireless
interface card that allows the CV7 to communicate with a NetLinx Master via a standard
802.11b Wireless Access Point, and an NXA-BASE/1 battery base kit that allows the
NXT to function off the charge from the included single NXT-BP battery.
CV7 panels feature programmable firmware that can be upgraded via either the Ethernet
port, wireless interface card, or the mini-USB port.
NXT-CV7
NXD-CV7 (shown with Button Trim Ring installed)
base
Sleep/Setup Access Button
Programmable
Buttons/LEDs
(1-3)
Programmable
Buttons/LED
(4-6)
Sleep/Setup Access Button
FIG. 2 NXT-CV7 and NXD-CV7 (front views)
The Button Trim Ring is factory installed only on the FG2259-02 and FG2259-03
panel models.
2
7" Modero Widescreen Touch Panels
Introduction
CV7 Specifications
The following table outlines the specifications for the 7" Widescreen Modero panels.
Specifications for 7" Widescreen Video Touch Panels
Dimensions (HWD):
• NXA-RK7: metal rack-mount with black matte finish:
(4 RU - rack units high)
6.97" x 19.0" x 0.50" (17.70 cm x 48.26 cm x 1.27 cm)
• NXT-CV7 (Fully raised): 6.86" x 7.96" x 6.93"
(17.40 cm x 20.20 cm x 17.60 cm)
• NXT-CV7 (Fully lowered): 3.70" x 7.96" x 6.93"
(9.40 cm x 20.20 cm x 17.60 cm)
• NXD-CV7 (with faceplate): 5.93" x 7.87" x 3.28"
(15.06 cm x 20.00 cm x 8.33 cm)
• CB-TP7 Conduit/Wallbox (optional): 5.47" x 7.23" x 3.40"
(13.90 cm x 18.40 cm x 8.64 cm)
Power Requirements
(stand-alone CV7):
• Constant current draw: 1.0 A @ 12 VDC (stand-alone)
Power Requirements
(CV7 and BASE/1):
• Constant current draw: 2.4 A @ 12 VDC
Minimum power supply
required:
• PSN2.8 Power Supply (FG423-17)
- when used with a stand-alone CV7 unit.
• Startup current draw: 1.5 A @ 12 VDC (stand-alone)
• Startup current draw: 3.6 A @ 12 VDC
• PSN4.4 Power Supply (FG423-45)
- when a CV7 is connected to a BASE/1. Using accessories can increase
the power draw requirements.
Memory (factory default):
• 64 MB SDRAM
• 64 MB Compact Flash (upgradeable to 1 GB - factory programmed)
Weight (stand-alone):
• NXD-CV7: 4.12 lbs (1.87 kg)
• NXTCV7: 4.12 lbs (1.87 kg)
Panel LCD Parameters:
• Aspect ratio: 16 x 9
• Brightness (luminance): 350 cd/m2
• Channel transparency: 8-bit Alpha blending
• Contrast ratio: 200:1
• Display colors: 256 thousand colors (18-bit color depth)
• Dot/pixel pitch: 0.19 mm
• Panel type: TFT Color Active-Matrix
• Screen resolution: 800 x 480 pixels (HV) @ 60 Hz frame frequency
• Video format: NTSC, PAL, and SECAM
• Viewing angle (100° total viewing angle):
Horizontal: + 50° (left and right from center)
Vertical: + 55° (up from center) and - 45° (down from center)
IR Reception Angle:
• Horizontal: + 50° (left and right from center)
Supported Audio Sample
Rates:
48000Hz, 44100Hz, 32000Hz, 24000Hz, 22050Hz, 16000Hz, 12000Hz,
11025Hz, and 8000Hz.
Certifications:
• FCC, CE, and EN 60950
• Vertical: + 30° (up and down from center)
7" Modero Widescreen Touch Panels
3
Introduction
Specifications for 7" Widescreen Video Touch Panels (Cont.)
Front Panel Components:
Light sensor:
• Photosensitive light detector for automatic adjustment of the panel brightness
(a dim room results in a dimmer LCD display, and a bright room results in a
brighter LCD display).
Note: The light sensor can be adjusted via the Sensor Setup page (page 101).
Motion sensor (PIR):
• Proximity Infrared Detector to wake the panel when the panel is approached.
• Activation range: + 45° (left and right from center) and + 20° (up and down
from center).
Note: This sensor can be adjusted via the Sensor Setup page (see page 101).
IR Receiver:
• IR reception 38 KHz and 455 KHz IR frequencies.
• The IR receiver is located beneath the translucent Front Setup button. When
an IR code is detected it is sent to the NetLinx Master as a push on the
appropriate AMX IR channel.
• IR receivers and transmitters on G4 panels share the device address number
of the panel.
Front setup access button:
• Provides both access to the Setup and Calibration page and toggles the
panel between a "sleep" or "wake" state.
- When wired, "sleep" status means the backlight is Off.
- When battery operated, wireless "sleep" status means the touch panel
base is either Off or "suspended".
Microphone:
• Used for intercom applications
(requires the NXA-AVB/ETHERNET Breakout Box for analog
communication)
Speakers:
• Stereo output with a frequency response of 500 Hz - 7 KHz
LEDs (NXD panels only):
• 6 blue LEDs (support On and Off)
- Both the LEDs and pushbuttons are only available when using the default
Button Trim Ring on the NXD panel.
Buttons (NXD panels only):
Rear Panel Components:
Mini-USB connector:
• 6 programmable pushbuttons
(Side panel location on NXD-Wall Mount panels)
• 5-pin Mini-USB connector used for programming, firmware update, and touch
panel file transfer between the PC and the target panel.
Note: When connecting the panel to PC using a CC-USB (or compatible)
cable, be sure to power the panel On before attempting to connect the USB
cable from the PC to the mini-USB port on the panel. Refer to the Configuring
and Using USB with a Virtual Master section on page 49 for more
information.
Stereo Output connector:
• Stereo output through a 3.5mm mini-jack (for use with external speakers or
headphones).
Ethernet 10/100 port:
• RJ-45 port for 10/100 Mbps communication. The Ethernet port automatically
negotiates the connection speed (10 Mbps or 100 Mbps), and whether to use
half duplex or full duplex mode.
• CV7 panels communicate with the NetLinx Master using the ICSP protocol
over Ethernet.
Ethernet 10/100 LEDs:
• LEDs show communication activity and connection information:
A-activity - Yellow LED lights when receiving or transmitting Ethernet data
packets.
L-link - Green LED lights when the Ethernet cables are connected and
terminated correctly.
USB connector:
• Type-A USB port can connect an external keyboard or mouse device for use
with Virtual PC applications.
Note: External USB input devices (keyboard or mouse) must be plugged into
the rear/side USB connector before the unit is powered-up. The panel will not
detect these USB input devices until the unit cycles power.
4
7" Modero Widescreen Touch Panels
Introduction
Specifications for 7" Widescreen Video Touch Panels (Cont.)
Rear Panel Components
(Cont.):
Audio/Video connector:
(Side panel location on NXD-Wall Mount panels)
• RJ-45 connector for communication of differential audio/video signals
to/from the touch panel (panel type dependant). This connector receives
Composite video, Stereo (left/right) audio, and microphone audio.
• Video is received via the NXA-AVB/ETHERNET Breakout Box. Configuring
video windows for playback is done using TPDesign4.
• In-bound audio (from the breakout box) gets directed to the speakers.
• Out-bound audio is sent from the on-board microphone (on the
front-panel). Selecting audio files for playback is configured through
TPDesign4.
PWR connector:
Button Assignments
(NXD-CV7 only):
• 2-pin 3.5 mm mini-Phoenix connector.
Button assignments can only be adjusted in TPD4 and not on the panels.
• Button channel range: 1 - 4000 button push and feedback (per address port)
• Button variable text range: 1 - 4000 (per address port)
• Button states range: 1 - 256 (General Button; 1 = Off State, 2 = On State)
• Level range: 1 - 600 (default level value 0-255, can be set up to 1-65535)
• Address port range: 1 - 100
Operating / Storage
Environment:
• Operating Temperature: 0° C (32° F) to 40° C (104° F)
• Operating Humidity: 20% - 85% RH
• Storage Temperature: -20° C (-4° F) to 60° C (140° F)
• Storage Humidity: 5% - 85% RH
Included Accessories:
• Trim Ring with button openings (60-2258-16)
(factory installed on NXD models only)
• Trim Ring without button openings (60-2258-21) (NXD models only)
• Installation Kit for 7" NXD panels (KA2258-02) includes:
- One 2-pin 3.5 mm mini-Phoenix connector (41-5025)
- Two Phillips-head screws (#4-40 x 0.250 Black) (80-0112)
- Three Drywall clips (62-5924-05) and #6 -metal strips (80-0192)
• Installation Kit for 7" NXT panels (KA2258-01):
- 2-pin 3.5 mm mini-Phoenix connector (41-5025)
• Modero Table Top Cable (CA2250-50): provided with all NXT panels.
• NXA-AVB/ETHERNET Breakout Box (FG2254-10): Provides video/audio
distribution to the A/V panel over CAT5 cable (up to 200’/60.96m) and
accepts either Composite or S-Video.
- Although the CV7 is only sold as part of a KIT configuration, the breakout
box can be purchased as a separate accessory.
Optional Accessories:
• CB-TP7 (FG035-10)
- 7" metallic conduit box for Wall Mount installations.
• CC-USB (Type A) to Mini-B 5-Wire programming cable (FG10-5965)
• NXA-BASE/1 Battery Base Kit (FG2255-05K)
- 1 battery base and 1 NXT-BP battery (NXT panels only)
• NXA-RK7 (FG2904-53)
- RackMount kit for 7" Wall Mount touch panels (NXD panels only).
Kit includes eight #10-32 screws and washers.
• NXA-WC80211B/CF (FG2255-03)
- AMX 802.11B Compact Flash Wireless Network Card
7" Modero Widescreen Touch Panels
5
Introduction
Specifications for 7" Widescreen Video Touch Panels (Cont.)
Optional Accessories::
• NXT-BP (FG2255-10)
- Battery pack for Table Top panels.
• NXT-CHG Kit (FG2250-50K)
- 1 battery charger and 2 NXT-BP batteries
• PSN2.8: Power Supply (FG423-17) with 3.5 mm mini-Phoenix connector
• PSN4.4: Power Supply (FG423-45) with 3.5 mm mini-Phoenix connector
• PSN6.5: Power Supply (FG423-41) with 3.5 mm mini-Phoenix connector
Upgrade Compact Flash (factory programmed with firmware):
NXA-CFSP128M - 128 MB Compact Flash card (FG2116-36)
NXA-CFSP256M - 256 MB Compact Flash card (FG2116-37)
NXA-CFSP512M - 512 MB Compact Flash card (FG2116-38)
NXA-CFSP1G - 1 GB Compact Flash card (FG2116-39)
It is recommended that firmware KIT files only be transferred over a direct USB
or Ethernet connection and only when the panel is connected to a power
supply. If battery power or wireless connection fails during a firmware upgrade,
the panel flash file system may become corrupted.
CV7 Panels - Connector Layout
FIG. 3 shows the layout of the connectors (located on the rear of the base on the NXT and on the
left side panel of the NXD panels).
Ethernet (CAT5)
Keyboard/Mouse
(USB)
Stereo Output
A
Audio-Video from
NXA-AVB/ETHERNET (CAT5)
L
12VDC
Mini-USB
(Program)
Power
P RO G R AM
E TH ER NE T
10/100
NXT-CV7 - connectors located
on rear panel of the base
KEY BO ARD /
M O U SE
A U DIO / VID EO
PWR
NXD-CV7 - connectors located
on left side panel
FIG. 3 Connector layout on the CV7 touch panels
6
7" Modero Widescreen Touch Panels
CV7 Touch Panel Accessories
CV7 Touch Panel Accessories
The following section outlines and describes the CV7 accessories (both the included and optional).
NXA-AVB/ETHERNET Breakout Box (FG2254-10)
The NXA-AVB/ETHERNET Breakout Box (FIG. 4) is included as part of the CV7 Kit
configuration (panel and box) but can be purchased as a separate accessory. This box facilitates the
installation and distribution of video, data, and audio to Modero touch panels located up to 200 feet
(60.96 m) from the AVB box. This unit accepts either Composite or S-Video from standard video
devices.
This breakout box can be mounted on either a horizontal flat surface or within an equipment rack
(by using an optional AC-RK Rack Kit).
Composite/
S-Video
Luma
(rear)
Audio
In
Ethernet (to panel)
S-Video Chroma
Power In
(front)
Mic Out
Ethernet In
Power (to panel)
Audio/Video
(to panel)
FIG. 4 NXA-AVB/ETHERNET Breakout Box (front and rear views)
Product Specifications
NXA-AVB/ETHERNET Specifications
Dimensions (HWD):
• 1.50" x 5.55" x 4.88" (3.81 cm x 14.10 cm x 12.40 cm)
• Width when attached to mounting ears: 6.65" (16.89 cm)
Power Consumption:
• 50mA (with audio/video input)
• 23mA (with no audio/video)
• Routed through NXA-AVB/Ethernet using a PSN6.5 power supply
Certifications:
• FCC, CE, and EN 60950
Features:
• Accepts either Composite or S-Video (video-capable panels only)
• Provides audio distribution to the non-video touch panels over a CAT5 cable
(up to 200 ft.)
• Provides video/audio distribution to the video-capable touch panels over
CAT5 cable up to 200 ft.(60.9 m)
Availability:
• This unit is included with CV7 and 1200V-Series Video Kits
Front Components:
• 2-pin 3.5 mm Phoenix connector for power to the touch panel
• Green LED provides an indication of power status
• RJ-45 connector provides Ethernet signals to the touch panel
• RJ-45 connector provides differential audio and video signals to the touch
panel (panel type dependant)
7" Modero Widescreen Touch Panels
7
CV7 Touch Panel Accessories
NXA-AVB/ETHERNET Specifications (Cont.)
Rear Components:
• 6-pin 3.5 mm Phoenix connector for in-bound (left/right channel) audio
• 4-pin 3.5 mm Phoenix connector for out-bound (from microphone) audio
• BNC connector (female) for Composite or Chroma (for video-capable
panels only)
• BNC connector (female) for luminance (for video-capable panels only)
• RJ-45 connector for Ethernet input from the control system
• 2-pin 3.5 mm Phoenix connector for in-bound power
Included Accessories:
• Two 2-pin Phoenix connectors (41-5025)
• 4-pin Phoenix connector (41-5047)
• 6-pin Phoenix connector (41-5063)
• Rack Mount Kit (KA2250-40) with mounting bracket (62-2254-02)
Optional Accessories:
• AC-RK Accessory RackMount Kit (FG515)
• Modero Table Top Cable (CA2250-50)
• PSN4.4 power supply (FG423-45) (panel dependant)
• PSN6.5 power supply (FG423-41) (panel dependant)
Installing the NXA-AVB/ETHERNET
A PSN power supply can indirectly provide power to a Modero panel by routing power through the
NXA-AVB/ETHERNET Breakout Box. FIG. 5 shows a sample wiring configuration using both an
indirect or direct PSN power connection for a video-capable Modero panel.
Indirect
Connect
Ethernet In
(RJ-45)
Mic Out
(4-pin captive-wire)
Video In
(BNC)
PSN power
supply
Line Level out
(to amplifier
or VOL card)
Audio In
(6-pin captive-wire)
(rear)
NXA-AVB/ETHERNET
Breakout Box
PSN
supplied via
NXA-AVB box
(front)
Ethernet
(CAT5)
PSN power
supply
Direct
Connect
Audio/Video
(CAT5)
or
NXD/T Video-capable
Touch Panels
FIG. 5 Sample wiring configuration on video-capable panels using this breakout box
A PSN power supply can also directly provide power through the unit to a target Modero panel.
FIG. 6 shows a sample wiring configuration for a non-video capable Modero panel.
8
7" Modero Widescreen Touch Panels
CV7 Touch Panel Accessories
Direct
connect
Ethernet
(CAT5)
PSN power
supply
Audio (CAT5)
between the
NXA-AVB/ETHERNET
Breakout Box
NXD/T Non-video capable
Touch Panels
FIG. 6 Sample wiring configuration using CA Modero panels
The breakout box unit can be mounted on either a horizontal flat surface or into an
equipment rack (by removing the front screws and attaching it to an optional AC-RK).
The PSN power supply being used on the NXA-AVB/ETHERNET is dependant on the
power requirements of the target touch panel.
Use a standard CAT5 Ethernet cable to provide both communication and 10/100 network
connectivity between the panel, NXA-AVB/ETHERNET, NetLinx Master, and the network.
Wiring the NXA-AVB/ETHERNET connectors and cables
The inputs and outputs on the breakout box are separated into front and rear connectors. The rear
connectors are used to input external signals. The front connectors are used to communicate signals
between the NXA-AVB/ETHERNET and a target Modero panel. FIG. 7 provides a layout of the
wiring connection both into and from the breakout box.
GND
Audio In - Left Channel
F
R
O
N
T
In (-)
(6-pin captive wire)
In (+)
Audio In - Right Channel
NXA-AVB/ETHERNET
Breakout Box
(6-pin captive wire)
GND
In (-)
In (+)
Microphone Out
GND(-)
Out (-)
(4-pin captive wire)
Out (+)
Comp/Y (BNC)
C (BNC)
Ethernet
(RJ-45)
PSN power
supply
R
E
A
R
Audio/Video
(CAT5)
Ethernet Out
(CAT5)
Power to
touch panel
FIG. 7 NXA-AVB/ETHERNET Breakout Box connector wiring diagram
The rear-panel wiring connections are described below (from left to right):
• AUDIO IN:
6-pin mini-Phoenix connector, divided into left and right audio channels. Each
channel is divided into GND, IN+, and IN- terminal cable connectors (2 sets of
3 for each channel).
An example of this cable is to strip the ends of 2 RCA audio cables and insert
them into their respective locations on the Audio In port.
Either a balanced (+, -, and GND) or unbalanced (+ and GND) audio
signal can be connected to this input.
7" Modero Widescreen Touch Panels
9
CV7 Touch Panel Accessories
• MIC OUT:
4-pin mini-Phoenix connector, divided into GND, OUT-, and OUT+ terminal
connectors.
An example of this cable is to strip the terminal ends of a 3.5mm mini-jack and
insert them into their respective locations on the Mic Out port. This signal can
be fed as a Line Level In to either an amplifier or an AMX VOL card.
Either a balanced (+, -, and GND) or unbalanced (+ and GND) audio signal
can be connected to this output.
• Video In BNCs: Feeds either Composite/S-Video Luma or S-Video Chroma signals into the
NXA-AVB/ETHERNET. This feed is then redirected out to a Modero panel
through the front Audio/Video CAT5 port.
• ETHERNET:
RJ-45 connector routes data to the G4 touch panel through the front Ethernet
port. These connections use a standard CAT5 Ethernet cable to provide
communication between the target touch panel, breakout box, and NetLinx
Master.
• PWR
2-pin mini-Phoenix connector that connects to a PSN power supply. This port
can be used to provide power to a Modero panel by sending it through the
NXA-AVB/ETHERNET (rear power connector through to the front power
connector).
Wiring the NXA-AVB/ETHERNET for Unbalanced Audio
Most domestic audio equipment has unbalanced audio inputs and outputs. This means that the
audio output (left, right, or mono) appears on a single wire, and is referenced to "0 V" or "Ground".
Typical connectors used are RCA "phono" connectors, DIN plugs/sockets, and 0.25" (6.3mm) or
3.5mm jack plugs/sockets.
Unbalanced audio is adequate for most domestic environments and for line-level signals in a typical
broadcast studio. Problems may occur if the signals are carried over long distances, especially if the
source and destination have separate main supplies. Use the following wiring drawing (FIG. 8) to
configure an unbalanced audio connection.
GND
ININ+
Left Channel
GND
IN-
Right Channel
Unbalanced IN
(Jumper IN- to GND)
Unbalanced IN
(Jumper IN- to GND)
IN+
AUDIO IN
MIC OUT
GND
OUTOUT+
Microphone
Unbalanced OUT
FIG. 8 Wiring the rear AUDIO IN and MIC OUT for use with Unbalanced Audio
When using unbalanced audio for the AUDIO IN connector (FIG. 8), the "-" and the "GND"
terminals should be connected together and then connected to the GND of the unbalance audio
signal. When connecting to an unbalanced audio input from the MIC OUT connector (FIG. 8), wire
the "+" terminal to the signal input, and the "GND" terminal to the signal ground.
10
7" Modero Widescreen Touch Panels
CV7 Touch Panel Accessories
Wiring the NXA-AVB/ETHERNET for Balanced Audio
Professional audio equipment will often use balanced audio inputs and outputs, usually on 3-pin
"XLR" connectors. A balanced audio signal consists of a pair of wires carrying the audio signal in
anti-phase with each other (if one wire carries a positive voltage, the other carries an equal and
opposite negative voltage).
The advantage of balanced audio over unbalanced audio is its ability to reject external interference
added as the signal is carried over the wire. The receiving equipment takes the voltage difference
between the two wires as the input signal. Interference will usually get added to both wires equally,
and so gets cancelled by the receiving equipment.
The 3 wires used in a typical XLR lead are often referred to as Ground, Live (Hot) and Return
(Cold). "Live" and "Return" carry the "in-phase" and "out-of-phase" versions of the audio
respectively. The pins of the XLR plug/socket are as follows:
• X = Ground
• L = Live (Hot)
• R = Return (Cold)
When connecting the MIC OUT connector to a balanced audio input (FIG. 9), use all three audio
terminals (+, -, and GND), then connect the "+" terminal to the "live" signal, the "-" terminal to the
"return" signal, and the "GND" terminal to the ground signal.
Ground signal
GND
OUTOUT+
Return signal
Balanced OUT
Line signal
FIG. 9 Wiring the rear MIC OUT connector for use with Balanced Audio
Modero Table Top Cable (CA2250-50)
The CV7 Table Top Touch Panel comes with a standard 10' (3.048 m) Modero cable (CA2250-50)
that supports Ethernet, Audio/Video, and Power connections. The cable comes terminated with two
RJ45 connectors (Ethernet and Audio/Video) and a single 2-pin mini-Phoenix connector for power.
FIG. 10 10 Foot Modero Table Top Cable
7" Modero Widescreen Touch Panels
11
CV7 Touch Panel Accessories
Product Specifications
Modero Table Top Cable Specifications
Dimensions (HWD):
• Length: 10 feet (3.048 m)
Connectors:
• Ethernet RJ-45 connector (White) routes Ethernet signals between the touch
panel and the NXA-AVB/ETHERNET Breakout Box.
• Audio/Video RJ-45 connector (Black) routes differential audio/video signals
between the touch panel and the box.
• 2-pin 3.5 mm mini-Phoenix power connector to route power from the external
breakout box to the target panel.
Included Accessories:
• Modero Table Top Cable (CA2250-50)
Wiring information for the Modero Table Top cable
If your installation requires custom cable configurations, you can purchase bulk (non-terminated)
cable from Liberty Wire and Cable under the nomenclature "AMX Table Top Cable - Modero"
(phone#: (800) 530 8998 or +1-719-388-7518).
When building a custom Table Top cable, please refer to the table below to calculate the maximum
length of the cable for your particular installation/setup.
Maximum Table Top Cable Lengths for Modero Panels
Panel Sizes:
7" Panel
10" Panel
12" Panel
15" Panel
17" Panel
39’ (11.89 m)
10’ (3.05 m)
15’ (4.57 m)
10’ (3.05 m)
Setup I: Using a panel without a battery base*:
Maximum cable length
150’ (45.72 m) 150’ (45.72 m) 49’ (14.94 m)
Setup II: Using a panel with a battery base*:
Maximum cable length
56’ (17.07 m)
56’ (17.07 m)
25’ (7.62 m)
* The total Modero cable run from the 13.5 V power source (PSN4.4).
* The total Modero cable run from the 13.5 V power source (PSN6.5).
FIG. 11 shows the top and cross-section views of the Table Top cable.
6 inches
3 inches
Red
3
3
2
2
1
1
Red
To Touch Panel
Connector 1 - used for Audio/Video (Black)
To Breakout Box
Connector 3 - used for Power
Connector 2 - used for Ethernet (White)
FIG. 11 Modero Table Top cable (top and cross-section views)
12
7" Modero Widescreen Touch Panels
CV7 Touch Panel Accessories
The following table provides the wiring information (color coding) for each of the three available
cable connectors on each side of the Modero Table Top Cable.
Modero Table Top Cable Wiring Table
Wire
Connector 1
Connector 2
Connector 3
1
White/Orange
White/Orange
Red
2
Orange/White
Orange/White
Black
3
White/Green
White/Green
-
4
Blue/White
Blue/White
-
5
White/Blue
White/Blue
-
6
Green/White
Green/White
-
7
White/Brown
White/Brown
-
8
Brown/White
Brown/White
-
The following figures provide a cross-section view (FIG. 12) and a description (FIG. 13) of the
Modero Table Top Cable:
Element #1
Connector #1 & 2
Binder
Element #2
Connector #3
Jacket
FIG. 12 Table Top Cable - cross-section view
DESCRIPTION:
9/PAIRS COMPOSITE CABLE CONSISTING OF: ELEMENT #1:
TWO 4/PAIR 24 AWG STRANDED TINNED COPPER,
POLYETHYLENE INSULATION, ELEMENT #2: 1/PAIR 18 AWG
STRANDED TNNED COPPER, PVC INSULATION AND FOIL
SHIELDED OVERALL PAPER BINDER AND FLEX-PVC JACKET.
2 X 4/PAIRS:
24 AWG STRANDED COPPER
ELEMENT #1:
CONDUCTOR: 24 AWG 7/32 TINNED COPPER; OD .024" NOMINAL
.0075" WALL POLYETHYLENE; OD .039" NOMINAL
INSULATION:
COLOR CODE: P1: WHITE/BLUE, BLUE
P2: WHITE/ORANGE, ORANGE
P3: WHITE/GREEN, GREEN
P4: WHITE/BROWN, BROWN
2 CONDUCTORS TWINNED LEFT HAND LAY
PAIR:
(TWISTED AT VARIED LAYS TO MINIMIZE CROSS TALK)
4/P CABLED LEFT HAND LAY (BLUE BINDER, ORANGE BINDER)
CABLE:
PAPER TAPE
BINDER:
1 PAIR: 18 AWG SHIELDED
ELEMENT #2:
CONDUCTOR: 18 AWG 16/30 TINNED COPPER; OD .046" NOMINAL
.010" WALL PVC; OD .066" NOMINAL
INSULATION:
COLOR CODE: BLACK, RED
#22 7/30 TINNED COPPER
DRAIN WIRE:
ALUM/POLYESTER TAPE (FOIL SIDE IN)
SHIELD:
FINAL ASSEMBLY:
BINDER:
JACKET:
COLOR:
DIAMETER:
MARKING:
TWO ELEMENT #1 & ELEMENT #2 CABLED ON COMMON
AXIS TO MINIMIZE DIAMETER
CLOTH TAPE 25% OVERLAP
.045" WALL FLEXIBLE PVC,
BLACK MATT
.375 INCHES NOMINAL
NONE
FIG. 13 Table Top Cable - Specification Elements
7" Modero Widescreen Touch Panels
13
CV7 Touch Panel Accessories
Each bundle of 4 twisted pairs includes a colored tape indicator for identification.
NXA-WC80211B/CF 802.11b Wireless Card (FG2255-03)
CV7 touch panels can connect to a wireless network using an optional internal AMX 802.11b
compatible Wi-Fi Wireless Interface Card shown in FIG. 14.
FIG. 14 NXA-WC80211B/CF Wireless Interface Card (WIC)
This unit is certified and available for use in the United States (FCC), Canada (IC),
Europe (CE) and Japan (TELEC).
The NXA-WC80211B/CF Wireless Interface Card works with compatible 802.11b Wireless
Access Points such as the NXA-WAP200G. Please follow your particular Wireless Access Point’s
instruction manual for the correct procedures to setup either a secured or unsecured connection.
Specifications for NXA-WC80211B/CF
Dimensions (HWD):
• 2.07" x 1.68" x 0.21" (52.56 mm x 42.80 mm x 5.57 mm)
Weight:
• 0.88 oz (25g)
Description:
• 2.4 GHz Direct Sequence Spread Spectrum (DSSS) 802.11b 11M wireless
PC card with detachable Antenna.
Features:
• Wired Equivalent Privacy (WEP) 64-bit and 128-bit data encryption
• Diversity Antenna Connectors automatically select the best available signal
• Supports infrastructure (communications to wired networks via Access
Points), and roaming (standard IEEE 802.11b compliant)
Power Consumption:
• TX power consumption: < 265 mA
• RX power consumption: < 165 mA
• Sleep Mode: 2 mA - 15 mA
Operating Voltage:
• 5 / 3.3 V
RF Output Power:
• 15 dBm +/- 1 dBm
• Channels 1 - 11 (North America)
14
Radio Data Rate:
• 1Mbps, 2Mbps, 5.5Mbps, 11Mbps, Auto Rate
Network Standard:
• IEEE 802.11b
Interoperability:
• Interoperable with Wi-Fi (WECA) certified products
Number of Channels:
• 14
Security:
• WEP 64,128 bit, WPA/TKIP
Host Interface:
• Compact Flash Type I
7" Modero Widescreen Touch Panels
CV7 Touch Panel Accessories
Specifications for NXA-WC80211B/CF
Modulation:
• DSSS, DBSK, DQSK, CCK
LED Indicators:
• Power / Link activity
Antenna:
• 2, Ceramic (Diversity Supported)
Receive Sensitivity:
• @PER < 8%
11 Mbps: -83 dBm (max)
5.5 Mbps: -86 dBm (max)
2 Mbps: -89 dBm (max)
1 Mbps: -92 dBm (max)
Operating Channels:
• 11 Channels (USA, Canada)
• 13 Channels (Europe)
• 14 Channels (Japan)
• 4 Channels (France)
Wireless Restrictions:
• In R&TTE countries, such as France, the 802.11g frequency band is
restricted to 2454 - 2483.5 MHz (2.4 - 2.4835 GHz) and a max power output
of 100 mW EIRP outdoor.
Operating Environment:
• Temperature: 0°C ~ 70°C (non-operating) and -15 ~ 80°C (storage)
• Humidity (non-condensing): 5% ~ 95% RH
Certifications:
•
•
•
•
FCC (United States)
IC (Canada)
CE (Europe)
TELEC (Japan)
It is recommended that any upgrade of internal equipment be done simultaneously in
order to reduce the risk of damage to internal components.
Installation of the Wireless Card (Table Top Panel)
These procedures involve removing the outer housing, installing the wireless card, and then
securely replacing the outer housing back onto the NXT panel.
The CV7 panels do not come factory installed with the NXA-WC802.11B/CF wireless
interface card. This card must be ordered separately from AMX.
Step 1: Removing the NXT Outer Housing
1. Carefully detach all connectors from the rear of the touch panel.
Do not use Ethernet cables containing mounting boots. These boots could make
removal of the Ethernet connectors (from the panel) difficult and cumbersome.
2. Gently place the touch panel LCD facedown onto a soft cloth to expose the under-side of the
base (FIG. 15) and prevent scratching of the LCD. Tilt the base forward so that both the bottom
surface and Housing Screws are easily accessible.
3. While holding the outer housing and base plate at an angle (to prevent it from sliding), use a
grounded Phillips-head screwdriver to remove the four Housing Screws.
7" Modero Widescreen Touch Panels
15
CV7 Touch Panel Accessories
Unscrew these four Housing Screws
to remove the Circuit Board Cover
Base
Hinge Brackets (2)
Touch Panel
DO NOT REMOVE these screws
They secure the plastic base front cover.
FIG. 15 Location of the attachment screws underneath an NXT-CV7 panel base
Note the location of the four plastic adhesive "feet". Once the outer housing is
placed back onto the panel, these "feet" must be placed back onto their
original locations so they can fit into their provided openings on the Battery
Base.
4. Rotate the panel back over (while gripping the entire unit and outer housing) and rest the base
back onto a flat surface.
5. Gently push the LCD panel backwards to expose the Tilt Bracket/speaker assembly.
Tilt Bracket/speaker assembly
Tilt Bracket Screws (2)
These two screws must
first be removed before
being able to remove
the outer housing.
Outer Housing
Base
Hinge Brackets (2)
FIG. 16 Location of the Tilt Bracket screws
6. Locate the two screw holes at either sides of the front speaker grill and use a grounded
Phillips-head screwdriver to remove the two Tilt Bracket Screws (FIG. 16). This procedure
loosens the rear Tilt Bracket cover plate (with the AMX logo and Hinge brackets) and provides
greater flexibility for the removal of the outer housing. Without this step, the Hinge brackets
(FIG. 16) present an obstacle to the removal of the outer housing and restrict access to the
circuit board.
7. Tilt the LCD panel back up to gain better access to the Tilt Bracket cover plate.
16
7" Modero Widescreen Touch Panels
CV7 Touch Panel Accessories
8. In a single motion, carefully pull both the Tilt Bracket cover plate and outer housing up and
then out (away from the LCD panel) to expose the internal circuit board (FIG. 17).
Outer Housing
Tilt Bracket cover plate
(must be removed first)
Outer housing
installation holes
(located on front panel)
Base
FIG. 17 Removal of the outer housing and wireless card location
Step 2: Upgrading internal components (Compact Flash and Wireless cards)
1. Discharge any static electricity from your body by touching a grounded metal object.
2. Locate the 64 MB Compact Flash and Wireless Interface cards on the main board (FIG. 18).
Tilt Bracket
Front of panel
Compact Flash Card
(Slot 1)
Wireless Interface Card
(Slot 2)
Card Removal Grooves
Card removal grooves
FIG. 18 Location and orientation of the card slots (both CV7 panels)
3. Insert a grounded flathead screwdriver into one of the card removal grooves (located on either
side of the card), and gently pry the card up and off the connector pins. Repeat this process on
the opposite card removal groove. This alternating action causes the card to "wiggle" away
from the on-board connector pins.
4. Slip your finger into the opening between the connector pins and the card, and push the card
out to remove it.
5. Remove the upgrade card from it’s anti-static bag.
7" Modero Widescreen Touch Panels
17
CV7 Touch Panel Accessories
6. Insert the upgrade card into the connector opening with the arrow facing towards the pins, then
push it in firmly until the contact pins are completely inside the flash card and securely
attached to the connector.
Card removal
grooves
On-board connector with contact pins
Insert with arrow
facing towards the pins
Connector opening
FIG. 19 Removing/installing a compact flash card
7. Repeat steps 3-6 for installation of the (optional) NXA-WC80211B/CF 802.11b wireless
interface card into the remaining open card slot.
Any new internal card upgrade is detected by the panel only after power is cycled.
Step 3: Closing and Securing the NXT Enclosure
1. In a single motion, gently slide the rear Tilt Bracket cover plate back over the tilt mechanism
(located below the LCD) and (while angling the housing downwards) slide the outer housing
below the Tilt Bracket and towards the LCD (at a downward angle).
2. Locate the two screw holes at either sides of the front speaker grill.
3. Use a grounded Phillips-head screwdriver to both insert and secure the two Tilt Bracket Screws
(FIG. 16). This procedure resecures the rear Tilt Bracket cover plate (with the AMX logo and
Hinge brackets).
4. Press the outer housing forwards until it is aligned over the outer housing installation holes.
Once installed and secured, the tilt bracket prevents any further movement (FIG. 17).
5. Gently press down on the housing (toward the base) until it is securely positioned over the
circuit board and base.
6. While holding the circuit board cover in place, turn the panel back over until the LCD lies
facedown on a soft cloth and the under-side of the base is exposed.
7. Insert and secure the four Housing Screws (using a grounded Phillips-head screwdriver) in
their respective locations, as shown in FIG. 15 on page 16.
8. Replace any adhesive plastic "feet" that might have been removed during the removal process
of the outer housing. These "feet" must be placed back onto their original locations so they can
fit into their provided openings on the Battery Base.
18
7" Modero Widescreen Touch Panels
CV7 Touch Panel Accessories
9. Grasp both the LCD and housing and then rotate the entire unit back onto a flat surface.
10. Insert all connectors and apply power.
Installation of the Wireless Card (WallMount Panel)
These procedures involve removing the outer housing, installing the wireless card, and then
securely replacing the outer housing back onto the NXD panel.
The CV7 panels do not come factory installed with the NXA-WC802.11B/CF wireless
interface card. This card must be ordered separately from AMX.
Step 1: Removing the existing NXD Outer Housing
1. Detach all connectors from the side of the touch panel.
2. Remove the faceplate from the CV7.
3. Place the LCD facedown on a soft cloth to expose the under-side of the unit (FIG. 20) and
prevent scratching of the LCD.
Two (2) connector
overlay release latches
Unscrew these
four pan-head
housing screws
to remove the
back box
(2 per side)
FIG. 20 Location of the attachment screws and connector overlay release latches on an NXD back box
4. Firmly press down on both connector overlay release latches (located in front of the
connectors). Pressing down releases the connector overlay from atop the connectors.
The overlay connector must first be released before the rear back box can be
removed from the NXD-CV7 panel.
5. Gently slide the connector overlay away from the back box housing.
6. Unscrew the outer housing (back box) by using a grounded Phillips-head screwdriver to
remove the two sets of pan-head Housing Screws, located on other side of the connector
overlay (FIG. 20).
7" Modero Widescreen Touch Panels
19
CV7 Touch Panel Accessories
Caution: Speaker wires come
connected to this side of the main
board. Use caution when removing
the back box.
Connector Overlay must first be
removed from the side of the NXD
Compact Card
Slot #1 located
on the bottom slot
FIG. 21 Removing the rear back box from the main unit
The internal circuit board comes pre-wired to internal speakers located on the
internal side of the back box. If the back box is removed incorrectly, these speaker
wires can become disconnected and damaged.
7. Carefully lift-off the back box housing and angle it over to the side of the unit where the wires
are connected to the circuit board.
8. Gently lay the back box to one side of the unit. This exposes the internal circuit board
(FIG. 21). Take care not to place undue strain on the speaker cables.
Step 2: Installing the Upgrade Components (NXD)
1. Complete the procedures outline within the Step 2: Upgrading internal components (Compact
Flash and Wireless cards) section on page 17 and then continue with the following Step 3.
Step 3: Replacing and Securing the NXD Enclosure
1. Gently place the outer housing back onto the panel and align the four pan-head Housing
Screws holes along the edges of the outer housing.
2. Insert and secure the four pan-head Housing Screws back into their pre-drilled holes by using a
grounded Phillips-head screwdriver.
3. Slip the connector overlay back into the connector opening by inserting the top of the overlay
into the connector opening in an upwards direction.
4. Align the connectors to their respective locations and secure the overlay by pushing it towards
the connectors until the overlay securely snaps back into the overlay release latches.
5. Re-install the faceplate onto the panel. Refer to the Installing the Button Trim Ring section on
page 31 for more detailed faceplate installation information.
20
7" Modero Widescreen Touch Panels
CV7 Touch Panel Accessories
NXA-CFSP Compact Flash (2116-3x)
Every CV7 Modero panel is shipped with a 64 MB Compact Flash card (NXA-CFSP).
If possible, upgrade the panel’s internal components (Compact Flash or wireless
interface cards) prior to installing or using the panel.
The NXA-CFSP Compact Flash card is factory programmed with specific panel firmware and can
be upgraded to several sizes, up to 1GB:
Optional Compact Flash Upgrades
• NXA-CFSP128M - 128 MB Compact Flash card (FG2116-36)
• NXA-CFSP256M - 256 MB Compact Flash card (FG2116-37)
• NXA-CFSP512M - 512 MB Compact Flash card (FG2116-38)
• NXA-CFSP1G - 1 GB Compact Flash card
(FG2116-39)
Installation Procedures for the Compact Flash Card (Table Top Panel)
Refer to the procedures outlined within the Installation of the Wireless Card (Table Top
Panel) section on page 15.
Installation Procedures for the Compact Flash Card (WallMount Panel)
Refer to the procedures outlined within the Installation of the Wireless Card (WallMount
Panel) section on page 19.
NXT-BP Power Pack (FG2255-10)
The NXT-BP Power Pack (FIG. 22) is a rechargeable Lithium-Ion "smart" battery used to provide
power to the NXT Modero panel through the NXA-BASE/1 Battery Base. This battery incorporates
an on-board battery life indicator. The NXT-BP battery can be charged through either the base
(when connected to the CV7 panel) or through an optional NXT-CHG Modero Power Station.
Although this product is included within the NXA-BASE/1 Kit (Fg2255-05K), extra NXT-BP
Power Packs (FG2255-10) can be purchased separately as an optional accessory.
FIG. 22 NXT-BP Power Pack
7" Modero Widescreen Touch Panels
21
CV7 Touch Panel Accessories
Specifications for the NXT-BP
Dimensions (HWD):
• 0.69" x 3.50" x 5.81" (1.75 cm x 8.89 cm x 14.76 cm)
Power (Voltage):
• 11.1 Volts (nominal)
Weight:
• Single NXT-BP Power Pack: 1.0 lbs (0.45 kg)
Features:
• Battery Usage: 4 to 8 hours (time is usage dependant)
• Charge Capacity: 6000mAh
Operating / Storage
Environment:
• Operating Temperature: 0° C (32° F) to 40° C (104° F)
• Operating Humidity: 20% - 85% RH
• Storage/Discharge Temperature: -20° C (-4° F) to 60° C (140° F)
• Storage Humidity: 5% - 85% RH
NXA-BASE/1 Battery Base Kit (FG2255-05K)
The NXA-BASE/1 Kit contains a single NXT-BP battery and one battery base. The NXA-BASE/1
(FIG. 23) is a Modero accessory that allows an NXT-CV7 touch panel to function off the charge
from a single internally connected NXT-BP battery. The base provides both power and battery
information to the panel via the panel interface connector. The NXT-BP battery can be charged
through either the base (only when connected to the NXT-CV7 touch panel) or through an optional
NXT-CHG Modero Power Station Kit (FG2255-50K). When used with the optional battery base,
the CV7 panels will charge the battery during full operation.
Panel Interface
connector
NXT-BP
Modero Power Pack
NXA-BASE/1
Battery Base
FIG. 23 NXA-BASE/1 Kit (consists of one BASE/1 and a single NXT-BP)
Specifications for the NXA-BASE/1
Dimensions (HWD):
• 0.93" x 5.96" x 6.89" (2.36 cm x 15.14 cm x 17.51 cm)
Power Requirements:
• 1.4 A @ 12 VDC (max power draw while charging a single battery)
Weight:
• Base unit: 0.75 lbs (0.34 kg)
• Base and 1 battery: 1.75 lbs (0.79 kg)
Features:
• Charge time for single depleted battery: ~ 5 - 8 hours
• Must be connected to a Modero unit utilizing a PSN4.4 power supply
Operating / Storage
Environment:
• Operating Temperature: 0° C (32° F) to 40° C (104° F)
• Operating Humidity: 20% - 85% RH
• Storage Temperature: -20° C (-4° F) to 60° C (140° F)
• Storage Humidity: 5% - 85% RH
Included Accessories:
• NXA-BASE/1 (FG2250-05k): 1 battery base and 1 NXT-BP battery
Optional Accessories:
• NXT-CHG Kit (FG2250-50K):
1 charger and 2 NXT-BP batteries
• NXT-BP battery pack (FG2255-10) (additional)
22
7" Modero Widescreen Touch Panels
CV7 Touch Panel Accessories
Before beginning the installation of the battery base to the Modero panel, verify the
Modero panel has the latest firmware. Only the latest build incorporates the
necessary updates for using the Modero with the NXA-BASE/1. From the Battery
Base page, verify that the battery base is loaded with the latest NXA-BASE/1
firmware (v2.xx or higher).
Checking the NXT-BP charge
1. Press the Battery Life Indicator button (FIG. 24) once to illuminate the Battery Life LEDs and
display the percent charge remaining on the battery (this indication lasts a few seconds).
Battery Life (Charge) Display
Battery Life Indicator button
FIG. 24 NXT-BP Battery Pack (showing the battery life indicator and button)
2. Charge the NXT-BP battery by either inserting it into the battery base or from within the
optional NXT-CHG charger (which can sequentially charge up to two batteries).
It is recommended to fully charge this battery before using it to power an NXT-CV7
panel. If the 25% LED indicator is blinking, recharge your battery immediately.
This blinking indicates there is less than 5% of a charge remaining on the battery.
Installing an NXT-BP into the NXA-BASE/1
The base does not directly connect to a power supply. Instead, it receives the power necessary to
charge the battery from the Modero panel (through the Panel Interface connector).
1. Install the NXT-BP battery into the base’s battery compartment with the label-side facing up.
2. Align the battery connector with its corresponding battery connector port (located in the
battery compartment shown in FIG. 25).
NXT-BP Battery
Battery
Connector
Battery
Connector
Port
FRONT
FIG. 25 Battery installation
7" Modero Widescreen Touch Panels
23
CV7 Touch Panel Accessories
3. Carefully insert the NXT-BP into the base until the battery securely fits onto the Battery
Connector Port.
Installing the NXA-BASE/1 below an NXT-CV7 Panel
1. Power Off the panel before attempting to attach the NXA-BASE/1.
2. Place the battery base (with battery) onto a flat/level surface.
3. Turn the battery locking slider (FIG. 26) to one side until the locking mechanism is horizontal
to the base (going left to right) and the rear battery latch is pointing directly outward (away
from the LCD).
Alignment
pegs (2)
Panel Interface
connector (male)
Back
Battery
locking
mechanism
Battery
locking slider
(Battery not shown
for illustration purposes)
Front
Insert holes for
NXT-CV7 feet
Securing
pegs (2)
FIG. 26 NXA-BASE/1 showing Panel Interface and connector locations
4. Carefully angle the NXT-CV7 panel over the front alignment pegs (FIG. 27). The pegs assist in
both aligning and securing the panel to the base (the locking mechanism secures the base to
panel when done).
Alignment
pegs
Battery
locking
mechanism
(with locking
slider)
FIG. 27 NXA-BASE/1 shown aligning with NXT-CV7 panel
5. Insert the alignment pegs into their corresponding holes below the front of the panel.
6. Verify the alignment of the Panel Interface connectors between the panel (female connector)
and base (male connector) (FIG. 27).
24
7" Modero Widescreen Touch Panels
CV7 Touch Panel Accessories
7. Align the rear pegs and gently push the rear of the panel downwards until it is mounted atop
the battery base.
The battery base CANNOT be hot-swapped. An NXT can not be receiving power
(through a connected power supply) and then be connected to a battery base. Always
POWER OFF the panel before installing the NXA-BASE/1.
8. Slide the rear battery locking slider in the opposite direction. This turns the latching
mechanism and secures the panel to the base.
9. Upon successful connection, the AMX logo appears on the panel to indicate that the panel is
properly connected and receiving power.
Charging the NXT-BP using the NXA-BASE/1
1. Insert the single battery into the battery compartment shown in FIG. 26 on page 24.
2. Follow the procedures from the previous sub-section to attach the NXT-CV7 to the
NXA-BASE/1.
3. Insert a 2-pin connector from a power supply to the rear PWR connector on the NXT-CV7
Modero panel. Refer to the Battery Base Page section on page 95 to view the charging progress
of the connected NXT-BP.
NXT-CHG Battery Charger Kit (FG2255-50K)
The NXT-CHG Kit includes one charger and two NXT-BP batteries. The optional NXT-CHG
Modero Power Station (FIG. 28) is a two-slot, stand-alone battery charger that can be used to
recharge up to two NXT-BP batteries. The batteries are charged in the order they are inserted into
the charger. The NXT-CHG Slot 1 has the feature of being able to completely discharge and
recharge (recalibrate) a battery.
Battery Life indicator
NXT-BP Modero Power Pack (battery)
NXT-CHG Modero Power Station (charger)
FIG. 28 NXT-CHG Kit (consists of one NXT-CHG charger and two NXT-BP batteries)
7" Modero Widescreen Touch Panels
25
CV7 Touch Panel Accessories
Specifications for NXT-BP and NXT-CHG
Dimensions (HWD):
• 1.13" x 8.63" x 11.81" (2.86 cm x 21.91 cm x 30.00 cm)
Power Requirements:
• NXT-BP Battery Voltage - 11.1 Volts
• NXT-CHG: 90 - 264 VAC, 47-63 Hz, Single Phase
(using the included 24 VDC power supply)
Weight:
• 0.57 lbs (0.26 kg)
Features:
• Charge time for two depleted batteries: ~ 5 hours
• Charge Rate: 2.5 A @ 12 VDC
• 2-Bays: Sequential charging
• LED: One LED indicator in front of each bay which conveys the status of that
bay. Refer to the Reading the NXT-CHG LED Indicator section for more
information.
• Recalibration pushbutton (located between the bays): Initiates recalibration
sequence in the left bay only.
• Recalibration Time: less than 9 hours
Optional Accessories:
• NXT-CHG Kit (FG2250-50K):
- 1 charger and 2 NXT-BP batteries
• NXT-BP battery pack (FG2255-10) (additional)
Powering the NXT-CHG
Recalibration improves the reporting accuracy of the battery charge back to the
Modero panel.
The NXT-CHG Smart Battery Charger uses an included power supply to charge inserted batteries.
1. Connect the rear of the NXT-CHG to the power adapter.
2. Connect the power adapter to the provided power cord (with plug).
3. Provide power to the unit by connecting the power cord (with plug) into a power outlet that
meets the requirements outlined in the Specifications section for the NXT-CHG.
Reading the NXT-CHG LED Indicator
FIG. 29 shows the components on the NXT-CHG Smart Battery Charger.
Slot 1
(recalibration)
Slot 2
Slot 1
LED
Slot 2
LED
Recalibrate
Pushbutton
FIG. 29 Component locations on the NXT-CHG
26
7" Modero Widescreen Touch Panels
CV7 Touch Panel Accessories
There is one LED indicator on the front of each battery slot that indicates the status of that slot. The
blink patterns for these LEDs are described in the following table:
• Off:
No battery detected.
• Green Flashing:
Fast charging.
• Green Solid:
Fully charged.
• Yellow Flashing:
Recalibration in process.
• Yellow/Green:
Recalibration complete.
• Yellow Solid:
Standby (waiting for other battery to charge).
• Red Flash:
Error (problem with either the battery connection to the internal slot, or with
the battery itself).
Charging the NXT-BP batteries using the NXT-CHG
1. Review the Checking the NXT-BP charge section on page 23 to confirm the percentage of
charge remaining on the batteries.
2. Provide power to the charger (as outlined in the Powering the NXT-CHG section on page 26).
3. Align the battery connector with the corresponding charge slot.
4. Firmly insert the battery into the desired slot until the battery is both securely located within
the slot and there is activity from the corresponding Slot LED. Refer to the Reading the NXTCHG LED Indicator section on page 26 section for LED information.
Recalibrating the batteries
The recalibration process increases the accuracy of the battery charge level. Recalibration of the
batteries is only done upon a user request from the Modero on-screen Battery Base page.
Recalibration can only be done within Slot 1 on the NXT-CHG.
1. Place the selected battery securely into Slot 1 (left slot) until there is activity on the
Slot 1 LED.
2. Push the Recalibration pushbutton (located between the two slots) to initiate recalibration in
the left bay only.
7" Modero Widescreen Touch Panels
27
CV7 Touch Panel Accessories
28
7" Modero Widescreen Touch Panels
Installation
Installation
NXT panels are mounted onto flat (horizontal) surfaces in either a stand-alone or combo (NXT atop
an NXA-BASE/1 battery base) configuration. NXD panels are installed into either a pre-wall
surface (using a CB-TP7 conduit/wallbox) or a solid surface (using either solid surface or drywall
screws).
It is recommended that if you are planning on upgrading your panel components
(flash and wireless), you do so before beginning any panel installations.
Unpacking the Panel
1. Inspect and confirm the contents of the shipment box to verify you have all specified parts.
Refer to the Specifications for 7" Widescreen Video Touch Panels section on page 3 for more
information about included and optional accessories.
2. Carefully remove the panel from the shipping box.
3. Carefully peel the protective plastic cover from the LCD.
If the protective plastic LCD cover is not removed, the panel may not respond
properly to touch points on the LCD or allow proper screen calibration.
Installing the Internal Components
Installation of the internal components such as the upgraded Compact Flash and the
NXA-WC80211B/CF Wireless card are described in detail within the following sections:
NXA-WC80211B/CF 802.11b Wireless Card (FG2255-03) section on page 14.
NXA-CFSP Compact Flash (2116-3x) section on page 21.
Installing the No-Button Trim Ring
The NXD-CV7 panel is shipped from AMX with the default Button Trim Ring already installed.
The unit is also shipped with an separate Trim Ring containing no button openings (a No-Button
Trim Ring) that allows you, if desired, to change the default configuration of the NXD panel
Faceplate to that with no-button openings. In order to install this included No-Button Trim Ring,
you must first remove the factory-installed default Button Trim Ring, the six small buttons, and
associated two clear light pipes.
1. The outer Button Trim Ring is secured to the Faceplate with plastic latches. To remove the
Faceplate, simply pull it away from the panel by gently tugging it outwards until the entire
Faceplate comes away from the panel.
2. Turn the Faceplate over to expose the inside surface and view the Trim Ring latches (FIG. 30).
3. In a single motion, press down and then outwards on the three Trim Ring latches located along
the top of the internal surface of the Faceplate to begin removing the Button Trim Ring.
7" Modero Widescreen Touch Panels
29
Installation
Removing the Internal Faceplate from the panel exposes the pushbuttons and light pipes along
the inside of the Internal Faceplate.
4. Gently tug along the edges of the Button Trim Ring and work your way around the edges to
remove it from the Faceplate (FIG. 30).
CV7 Panel/enclosure
Button latch
B
Trim
Ring
Latches
Light Pipe latch
(black)
Default Button Trim Ring
(with button openings)
Button and Light Pipe removal
(showing the internal surface of Faceplate)
Faceplate
(outside surface shown)
FIG. 30 Removing the default Button Trim Ring
5. From along the internal surface of the Faceplate, remove the six buttons by gently bending
each Button latch up and pulling the button outwards.
6. Remove the pair of clear light pipe strips by bending the two black light pipe latches inwards
and pulling out the strip.
7. Grasp the No-Button Trim Ring on both sides and fit it into the groove along the outside
surface of the Faceplate (made available by the removal of the previous Trim Ring).
8. Gently insert the Trim Ring latches into their corresponding openings on the outer surface of
the internal Faceplate (FIG. 31).
9. Firmly press down around the No-Button Trim Ring until all of the latches are securely
inserted into their openings on the Faceplate, and the No-Button Trim Ring is securely
fastened. Verify the No-Button Trim Ring is firmly inserted onto the Faceplate and that there
are no gaps between this Trim Ring and the outer surface of the Faceplate.
10. Place the Faceplate back onto the main NXD-CV7 unit. Make sure to align the Microphone,
Light, and PIR Motion sensor locations on the main unit to their respective openings on the
Faceplate assembly.
30
7" Modero Widescreen Touch Panels
Installation
No-Button Trim Ring
Hollow button openings
Faceplate (outer surface shown)
FIG. 31 Inserting the No-Button Trim Ring
Installing the Button Trim Ring
The outer No-Button Trim Ring is secured to the Faceplate with plastic latches. In order to
re-install the Button Trim Ring back onto an NXD panel which has had the default Button Trim
Ring features removed; you must first remove the No-Button Trim Ring:
1. To remove the Faceplate, simply pull it away from the panel by gently tugging it outwards until
the entire Faceplate comes away from the panel.
2. Turn the Faceplate over to expose the inside surface and view the Trim Ring latches.
3. In a single motion, press down and then outwards on the three Trim Ring latches located along
the top of the internal surface of the Faceplate to begin removing the Trim Ring. Removing the
Internal Faceplate from the panel exposes the pushbuttons openings left from an earlier
removal of the pushbuttons and LEDs.
4. Gently tug along the edges of the No-Button Trim Ring and work your way around the edges
to remove it from the Faceplate (FIG. 32).
5. From along the internal surface of the Faceplate, install the six buttons by firmly inserting them
into the button openings until the Button latch secures the button in place (FIG. 32).
6. Install the pair of clear light pipe strips by pushing light pipes over the two black light pipe
latches.
7. Grasp the Button Trim Ring on both sides and fit it into the groove along the outside surface of
the Faceplate (made available by the removal of the previous Trim Ring).
7" Modero Widescreen Touch Panels
31
Installation
CV7 Panel/enclosure
Button latch
Trim
Ring
Latches
Light Pipe latch
(black)
Button and Light Pipe removal
(showing the internal surface of Faceplate)
No-Button Trim Ring
Faceplate
(outside surface shown)
FIG. 32 Removing the No-Button Trim Ring
8. Gently insert the Button Trim Ring latches into their corresponding openings on the outer
surface of the internal Faceplate (FIG. 33).
Button Trim Ring
Faceplate (outer surface shown)
Button openings
FIG. 33 Inserting the Button Trim RIng
9. Firmly press down around the Button Trim Ring until all of the latches are securely inserted
into their openings on the Faceplate, and the Button Trim Ring is securely fastened. Verify the
Button Trim Ring is firmly inserted onto the Faceplate and that there are no gaps between this
Trim Ring and the outer surface of the Faceplate.
10. Place the Faceplate back onto the main NXD-CV7 unit. Make sure to align the Microphone,
Light, and PIR Motion sensor locations on the main unit to their respective openings on the
Faceplate assembly.
32
7" Modero Widescreen Touch Panels
Installation
Pre-Wall Installation of the Conduit Box
Wall Mount panels (NXDs) are contained within an outer housing (back box). This back box is not
removed when installing the NXD into a Conduit Box (CB-TP7). The back box is only removed to
gain access for the replacement of the internal components.
INSTALLER: LEAVE A GAP BETWEEN THE STUD AND CONDUIT BOX
MOUNTING TABS TO ACCOMMODATE THE DRYWALL or SHEETROCK.
This gap allows the installation of the drywall or sheetrock after the CB-TP7 Conduit
Box has been installed.
The CB-TP7 is an optional metallic box that is secured onto a beam in a pre-wall setting (where no
walls are present). Installation procedures and configurations can vary depending on the
installation environment. This section describes the installation procedures for the most common
installation scenario. The most important thing to remember when mounting this conduit box is that
the NXD-CV7 Mounting Tabs must lie flush against the outside of the sheetrock (FIG. 34).
Refer to SP-2258-02 for detailed installation dimensions.
It is recommended that you cut out the surface slightly smaller than what is outlined in
the installation drawings so that you can make any necessary cutout adjustments.
The wiring knockouts on the left side will be used for the NXD-CV7 Wall Mount panel
connectors, so always secure the conduit box to the stud using the Stud Mounting Holes
on the right side of the box.
1. Rest the right Stud Mounting tabs onto the stud (keeping the knockouts on the left). Be sure to
leave enough of a gap between the stud and NXD Mounting tabs to accommodate the
installation of the drywall or sheetrock after the conduit box has been mounted.
Ultimately, the Mounting Tabs should lie flush against the outside of the sheetrock.
2. Fasten the CB-TP7 conduit box to the stud through the holes on the right Stud Mounting tabs
(FIG. 34), using either nails or screws.
Stud Mounting tabs
Stud
Wiring
knockouts
(must be
located on
left side)
NXD Mounting tabs
(should lie flush against
the outside of the wall)
Drywall or sheetrock
FIG. 34 CB-TP7 conduit box components
7" Modero Widescreen Touch Panels
33
Installation
3. Remove the wiring knockouts from the left side of the conduit box (CB-TP7)
(FIG. 34) to accommodate the cables being threaded through to the NXD touch panel.
Remember that when mounting this conduit box, the NXD mounting tabs must lie
flush against the outside of the sheetrock.
4. Thread the incoming power, RJ-45 audio/video, Ethernet, and USB wiring through the
knockouts (use of the left wiring knockouts are recommended with this installation).
Leave enough slack in the wiring to accommodate any re-positioning of the panel.
5. Install the drywall/sheetrock before inserting the main NXD unit into the CB-TP7.
Installation of an NXD Touch Panel
The NXD-CV7 can be installed either directly into the (optional) CB-TP7 or other solid surface
environment using the two different mounting options: drywall clips or solid surface screws. The
following sections describe mounting the touch panel directly into a pre-wall conduit box, a solid
surface or drywall, and optional NXA-RK7 Rack Mount Kit for installation.
Installing the NXD panel within a Conduit Box
The conduit box must be mounted prior to continuing this section. Refer to the procedures in the
Pre-Wall Installation of the Conduit Box section on page 33 for detailed pre-wall installation
instructions. Verify that all necessary cables have been threaded through the knockouts on the left of
the conduit box and the connections have been tested prior to installation of the NXD-CV7.
1. Remove the Faceplate/bezel (A in FIG. 35) from the main NXD unit
(B in FIG. 35) by gripping the faceplate and pulling with gentle outward force.
C - Optional CB-TP7
conduit/wallbox
#4-40 Mounting Screws
(four - included)
secure the NXD to
the Conduit Box
Stud
Mounting Tab
B - Main NXD unit consists of
the touch panel and back box housing
A - Faceplate/Trim Ring
default Faceplate comes with buttons
FIG. 35 NXD-CV7 panel installation into a CB-TP7 (pre-wall construction)
34
7" Modero Widescreen Touch Panels
Installation
2. Verify the incoming power, RJ-45 audio/video, Ethernet, and USB cables have been properly
threaded through the wiring knockouts on the left of the conduit box. Leave enough slack in the
wiring to accommodate any re-positioning of the panel.
3. Connect all data and power wiring connectors to their corresponding locations along the side
of the (un-powered) NXD touch panel.
Verify that the terminal end of the power cable is not connected to a power source before
plugging in the 2-pin power connector.
The USB connectors can be from either a USB extension cable, or a wireless USB RF
transmitter.
Don’t disconnect the connectors from the touch panel. The unit must be installed with
the attached connectors before being inserted into the conduit box.
4. Test the incoming wiring by connecting the panel connections to their terminal locations and
applying power. Verify that the panel is receiving power and functioning properly to prevent
repetition of the installation.
5. Disconnect the terminal end of the power cable from the connected PSN power supply.
6. Carefully slide the main NXD-CV7 unit (B in FIG. 35) into the conduit box, so that all
Mounting Tab lie flush against the conduit box (C in FIG. 35).
7. Insert and secure four #4-40 Mounting Screws (included) into their corresponding holes
located along the sides of the NXD.
8. Replace the Faceplate/Trim Ring (A in FIG. 35) back onto the main NXD unit
(B in FIG. 35). Make sure to align the Microphone, Light, and PIR Motion sensor locations to
their respective openings on the front faceplate/bezel.
9. Reconnect the terminal RJ-45, Ethernet, USB, and any optional audio/video wiring to their
respective locations (outside the conduit box) on either the NXA-AVB/ETHERNET Breakout
Box, Ethernet port, or NetLinx Master.
10. Reconnect the terminal power connector on the PSN and apply power.
Installing the NXD into drywall using Expansion Clips
Expansion clips are mounted through the three oval holes located along the rim of the NXD-CV7.
As the screw is tightened, the clip bends toward the insertion hole and into the wall. This bending
creates a "grip" on the wall by either pressing onto the wall or by securing the drywall between the
housing and the drywall clip.
The most important thing to remember when mounting the NXD is that the outer frame
(Mounting Tabs) must be installed flush against the mounting surface.
Refer to SP-2258-01 for detailed installation dimensions (reproduced in FIG. 36).
It is recommended that you cutout the surface slightly smaller than what is outlined in the
installation drawings so that you can make any necessary cutout adjustments.
7" Modero Widescreen Touch Panels
35
Installation
1. Remove any screws or nails from the drywall before beginning.
2. Cut out the surface for the NXD Wall Mount unit using the dimensions shown in FIG. 36. Be
sure to cut out the three notches along the sides to accommodate the three corresponding
drywall expansion clips (included).
FIG. 36 NXD-CV7 Wall Mount panel dimensions using expansion clips
3. Remove the Faceplate/bezel (A in FIG. 37) from the main NXD unit (B in FIG. 37) by
gripping the faceplate and pulling with gentle outward force.
4. Thread the incoming power, RJ-45, Ethernet, USB, and any optional audio/video wiring (from
their terminal locations) through the surface opening. Leave enough slack in the wiring to
accommodate any re-positioning of the panel.
5. Connect all data and power wiring connectors to their corresponding locations along the left
side of the (un-powered) NXD touch panel.
Verify that the terminal end of the power cable is not connected to a power source before
plugging in the 2-pin power connector.
The USB connectors can be from a either a USB extension cable, or a wireless USB RF
transmitter.
36
7" Modero Widescreen Touch Panels
Installation
3 notches are
required to
accommodate the
three expansion
clips (included)
Install the 3 included
drywall clip sets
into these locations
Drywall Clip (3)
Mounting Tab
A - Faceplate
/Trim Ring
B - Main NXD unit consists of
the touch panel and back box
FIG. 37 Wall Mount panel (NXD) installation configuration for drywall surfaces
Don’t disconnect the connectors from the touch panel. The unit must be installed with
the attached connectors before being inserted into the drywall.
6. Test the incoming wiring by attaching the panel connections to their terminal locations and
applying power. Verify the panel is receiving power and functioning properly to prevent
repetition of the installation.
7. Disconnect the terminal end of the power cable from the connected PSN power supply.
8. Install the three sets of drywall screws and expansion clips into the three oval notch locations
along both sides of the main unit (B in FIG. 37).
9. Carefully insert the main unit (with expansion clips) into the cutout until the Mounting Tabs on
the NXD unit lie flush against the wall.
The drywall clip set must be re-ordered from AMX if the drywall clip is bent
accidentally during an installation or removed during a re-installation.
10. Tighten all three drywall clip sets (screws and clips) until the entire Mounting Tab is securely
fastened and flush against the wall.
11. Place the Faceplate (A in FIG. 37) back onto the main NXD unit (B in FIG. 37). Make sure to
align the Microphone, Light, and PIR Motion sensor locations to their respective openings on
the front faceplate/bezel.
7" Modero Widescreen Touch Panels
37
Installation
12. Reconnect the terminal RJ-45, Ethernet, USB, and any optional audio/video wiring to their
respective locations on either the NXA-AVB/ETHERNET Breakout Box, Ethernet port, or
NetLinx Master.
13. Reconnect the terminal power connector on the PSN and apply power to the panel.
Installing the NXD into a Flat Surface using #4 screws
Mounting screws (#4-40, included) are secured through two sets of circular holes located at the left
and right sides of the NXD-CV7. The most important thing to remember when mounting the NXD
Wall Mount is that the outer frame (Mounting Tabs) must be installed flush against the mounting
surface.
Refer to SP-2258-01 for detailed installation dimensions (reproduced in FIG. 38).
It is recommended that you cutout the surface slightly smaller than what is outlined in the
installation drawings so that you can make any necessary cutout adjustments.
1. Remove any screws or nails from the surface before beginning the cutout process.
2. Cut out the surface for the NXD Wall Mount unit using the dimensions shown in FIG. 38.
FIG. 38 NXD-CV7 Wall Mount panel dimensions using #4-40 mounting screws
3. Remove the Faceplate/bezel (A in FIG. 39) from the main NXD unit (B in FIG. 39) by
gripping the faceplate and pulling with gentle outward force.
38
7" Modero Widescreen Touch Panels
Installation
4. Thread the incoming power, RJ-45, Ethernet, USB, and any optional audio/video wiring (from
their terminal sources) through the surface opening. Leave enough slack in the wiring to
accommodate any re-positioning of the panel.
5. Connect all data and power wiring connectors to their corresponding locations along the left
side of the (un-powered) NXD touch panel.
Verify that the terminal end of the power cable is not connected to a power source before
plugging in the 2-pin power connector.
The USB connectors can be from a either a USB extension cable, or a wireless USB RF
transmitter.
Don’t disconnect the connectors from the touch panel. The unit must be installed with
the necessary connectors before being inserted into the solid surface.
6. Test the incoming wiring by connecting the panel connections to their terminal locations and
applying power. Verify that the panel is receiving power and functioning properly before
finalizing the installation.
Attachment is done
along the edges
of the cutout
Flat installation surface
Install the four #4-40 Mounting Screws
(included) into these four holes
Mounting Tab
B - Main CV7 unit
A - Faceplate/Trim Ring
FIG. 39 Wall Mount panel installation configuration for flat surfaces
7. Disconnect the terminal end of the power cable from the power supply.
8. Carefully slide the main unit into the cutout until the Mounting Tabs of the CV7 unit lie flush
against the wall.
7" Modero Widescreen Touch Panels
39
Installation
9. Insert and secure four #4-40 Mounting Screws (included) into their corresponding holes
located along the sides of the NXD-CV7 (using a grounded Phillips-head screwdriver) until the
unit is secure and flush against the wall (FIG. 39).
10. Replace the Faceplate/Trim Ring on the main unit. Make sure to align the Microphone, Light,
and PIR Motion sensor locations to their respective openings on the front bezel/faceplate.
11. Reconnect the terminal RJ-45, Ethernet, USB, and any optional audio/video wiring to their
respective locations on either the NXA-AVB/ETHERNET Breakout Box, Ethernet port, or
NetLinx Master.
12. Reconnect the terminal power connector on the PSN and apply power.
Installing an NXD-CV7 into an (optional) Rack Mount Kit (NXA-RK7)
The NXA-RK7 is a 19" (48.3 cm) metal rack-mount (with black matte finish) measuring 4 rack
units high.
1. Remove the Faceplate/Trim Ring assembly from the main CV7 unit.
2. Thread the incoming power, RJ-45 audio/video, Ethernet, and USB wiring (from their terminal
sources) through the surface opening, leaving enough slack in the wiring to accommodate any
re-positioning of the panel.
3. Connect all data and power wiring connectors to their corresponding locations along the left
side of the (un-powered) NXD touch panel.
Verify that the terminal end of the power cable is not connected to the a power supply
before plugging in the 2-pin power connector.
The USB connectors can be from a either a USB extension cable, or a wireless USB RF
transmitter.
Don’t disconnect the connectors from the touch panel. The unit must be installed with
the necessary connectors before being inserted into the equipment rack.
4. Test the incoming wiring by connecting the panel connections to their terminal locations and
applying power. Verify that the panel is receiving power and functioning properly to prevent
repetition of the installation.
5. Disconnect the terminal end of the power cable from the connected power supply.
6. Carefully insert the CV7 panel into the NXA-RK7.
7. Secure the panel to the NXA-RK7 mount by first inserting and then tightening the four #4-40
screws.
8. Insert the NXA-RK7 (with connected NXD unit) into the equipment rack, making sure to align
the screw holes along the sides on the NXA-RK7 with the holes in the equipment rack.
9. Use a grounded Phillips-head screwdriver to secure the NXA-RK7 to the equipment rack using
#10-32 screws (included).
10. Replace the Faceplate/Trim Ring assembly back onto the main CV7 unit, making sure to align
the Microphone, Light, and PIR Motion sensor locations to their respective openings on the
Faceplate/Trim Ring assembly.
40
7" Modero Widescreen Touch Panels
Installation
11. Reconnect the terminal RJ-45 audio/video, Ethernet, and USB wiring to their respective
terminal locations on either the NXA-AVB/ETHERNET Breakout Box, Ethernet port, or
NetLinx Master.
12. Reconnect the terminal power connector on the PSN and apply power.
Wiring Guidelines for the CV7 Panels
CV7 panels require 12 VDC power from a PSN NetLinx Power Supply to operate properly. The
panels connect to the power supply via a 2-pin 3.5 mm mini-Phoenix connector.
These units should only have one source of incoming power. Using more than one
source of power to the touch panel can result in damage to the internal components
and a possible burn out.
Apply power to the panels only after installation is complete.
Preparing captive wires
You will need a wire stripper and flat-blade screwdriver to prepare and connect the captive wires.
Never pre-tin wires for compression-type connections.
1. Strip 0.25 inch (6.35 mm) of insulation off all wires.
2. Insert each wire into the appropriate opening on the connector (according to the wiring
diagrams and connector types described in this section).
3. Tighten the screws to secure the wire in the connector. Do not tighten the screws excessively;
doing so may strip the threads and damage the connector.
Using the PSN NetLinx connector for power
The PWR and GND cable from the NetLinx Power Supply (PSN4.4 or PSN6.5) must be connected
to the corresponding location on the 2-pin 3.5 mm mini-Phoenix connector (FIG. 40).
PWR +
NetLinx Power Supply
GND To the Touch Panel
FIG. 40 NetLinx power connector wiring diagram
1. Insert the PWR and GND wires on the terminal end of the PSN 2-pin 3.5 mm mini-Phoenix
cable. Match the wiring locations of the +/- on both the power supply and the terminal
connector.
2. Tighten the clamp to secure the two wires. Do not tighten the screws excessively; doing so may
strip the threads and damage the connector.
3. Verify the connection of the 2-pin 3.5 mm mini-Phoenix to the power supply.
7" Modero Widescreen Touch Panels
41
Installation
Audio/Video RJ-45 Connections and Wiring
The following table shows the signal and pinout/pairing information used on the RJ-45 Audio and
Video connections.
Audio/Video RJ-45 Pinout Information
Pin
Wire Color
Function
Polarity
1
Orange/White
Right Audio In
+
2
Orange
Right Audio In
-
3
Green/White
Video In
-
4
Blue
Mic Out
-
5
White/Blue
Mic Out
+
6
Green
Video In
+
7
White/Brown
Left Audio In
+
8
Brown
Left Audio In
-
T IA 5 6 8 B
1 2 3 4 5 6 7 8
1 2 3 4 5 6
7 8
(female)
(male)
RJ-45 connector - pin configurations
Ethernet 10/100 Base-T RJ-45 Connections and Wiring
FIG. 41 and the table below describe the pinouts, signals, and pairing for the Ethernet 10/100
Base-T RJ-45 connector and cable. The Ethernet cable is connected to the rear of Table Top and
side of the Wall Mount panels.
A - Activity LED (yellow)
lights when receiving or
transmitting Ethernet
data packets
A
L
L - Link LED (green) lights when
the Ethernet cables are connected
and terminated correctly.
ETHERNET
10/100
FIG. 41 Ethernet connector (showing communication and connection LEDs)
Ethernet RJ-45 Pinouts and Signals
42
1 2 3 4 5 6 7 8
Pin
Signals
Connections
Pairing
Color
1
TX +
1 --------- 1
1 --------- 2
Orange-White
3 --------- 6
Green-White
4 --------- 5
Blue-White
7 --------- 8
Brown-White
2
TX -
2 --------- 2
3
RX +
3 --------- 3
4
no connection
4 --------- 4
5
no connection
5 --------- 5
6
RX -
6 --------- 6
7
no connection
7 --------- 7
8
no connection
8 --------- 8
Orange
Blue
Green
1 2 3 4 5 6 7 8
Brown
7" Modero Widescreen Touch Panels
Installation
FIG. 42 RJ-45 wiring diagram
Connecting and Using USB Input Devices
The CV7 panel can have up to two USB-capable input devices connected for use on its different
firmware and TPD4 panel pages. These input devices can consist of a keyboard or mouse.
USB-connected input devices are not detected and recognized by the panel until
power is cycled to the unit.
A mini-USB connection is only detected after it is installed onto an active
panel. Connection to a previously powered panel, allows the PC to detect the
panel and assign an appropriate USB driver.
1. Insert the input device USB connectors into the appropriate USB connector on the panel.
2. Press the on-screen Reboot button from the Protected Setup page to save any changes and
restart the panel.
3. After the panel splash-screen disappears:
If a USB mouse has been connected, a mouse cursor appears on the panel screen and its
location corresponds to the mouse cursor position sent by the external USB mouse.
If a USB keyboard has been connected, only on-screen keyboards and keypads will
reflect any external keystrokes sent from the external USB keyboard.
7" Modero Widescreen Touch Panels
43
Installation
44
7" Modero Widescreen Touch Panels
Panel Calibration
Panel Calibration
This section outlines the steps for calibrating the touch panel. It is recommended that you calibrate
the panel before its initial use and after completing a firmware download.
Modero panels are factory setup with specific demo touch panel pages. The first splash screen that
appears indicates the panel is receiving power, beginning to load firmware, and preparing to display
the default touch panel pages. When the panel is ready, the AMX Splash Screen is replaced by the
Initial Panel Page (FIG. 43).
AMX Splash Screen
(appears during power-up)
Initial Panel Page
(AMX Logo Page)
FIG. 43 AMX splash screen and initial Panel Page
Calibrating the Modero Panel
1. Press and hold the grey Front Setup Access button (FIG. 44) for 6 seconds to pass-over the
Setup page and access the Calibration setup page (FIG. 45).
Front Setup
Access button (grey)
3 second press/hold:
Opens the Setup page
6 second press/hold:
Opens the Calibration page
Single press puts
the panel to sleep
FIG. 44 Location of Front Setup Access button
2. Press the crosshairs (on the Calibration page) to set the calibration points on the LCD
(FIG. 45).
7" Modero Widescreen Touch Panels
45
Panel Calibration
The request to touch the crosshairs
is the first on-screen message
Calibration successful is the second
on-screen message that appears
after the calibration process is
completed
On-screen crosshairs used for
calibration of the touch device
FIG. 45 Touch Panel Calibration Screens
3. After the "Calibration Successful.." message appears, press anywhere on the screen to
continue and return to the Setup page.
If the calibration was improperly set and you cannot return to the Calibration
page (through the panel’s firmware); you can then access this firmware page via
G4 WebControl where you can navigate to the Protected Setup page and press the
Calibrate button through your VNC window.
This action causes the panel to go to the Calibration page seen above, where you
can physically recalibrate the actual touch panel again using the above procedures.
Testing your Calibration
1. Press and hold down the on-screen Calibration button for 6 seconds to enter the Calibration
Test page (FIG. 46).
On-screen crosshairs is used to
verify a proper calibration of the
panel
FIG. 46 Calibration Test page
2. Press anywhere on this page to confirm the on-screen crosshairs match your touch points.
3. If the crosshairs do not appear directly below your LCD touch points, press the Back button
and recalibrate the panel using the above steps.
4. Exit this Calibration Test page by pressing the Back button to return to the Protected Setup
page.
46
7" Modero Widescreen Touch Panels
Configuring Communication
Configuring Communication
Communication between the Modero panel and the Master is done using either USB or
ETHERNET (DHCP or Static IP). Ethernet communication can be achieved through either a
direct connection (Ethernet) or through the use of the optional NXA-WC802.11B/CF wireless
interface card.
Before commencing, verify you are using the latest NetLinx Master firmware.
Verify the NetLinx Studio program being used is Version 2.3 or higher.
USB input devices must be plugged into the rear or side USB connectors before the
G4 panel is powered-up. The panel will not detect a USB connection of this type until
after the unit cycles power.
Modero Setup and System Connection
1. Press the grey Front Setup Access button for 3 seconds to open the Setup page (FIG. 47).
Connection Status
Red Connection Status icon indicates no connection
to a Master
Green Connection Status icon indicates communication
to a Master
Battery Base button doesn’t appear
until NXT is connected to a BASE/1
FIG. 47 Setup page
2. Press the Protected Setup button (located on the lower-left of the panel page) to open the
Protected Setup page and display an on-screen keypad.
3. Enter 1988 into the Keypad’s password field and press Done when finished.
Clearing Password #5, from the initial Password Setup page, removes the need for
you to enter the default password before accessing the Protected Setup page.
4. Press the red Device Number field to open the Device Number keypad (FIG. 48).
5. Enter a Device Number for the panel into the Device Number Keypad.
The default is 10001 and the range is from 1 - 32000.
When using multiple panels within a NetLinx System, remember to assign unique
Device Number values to each panel so that all assigned panels appear in the
System listing for the target Master.
6. Press Done to close the keypad, assign the number, and return to the Protected Setup page.
7" Modero Widescreen Touch Panels
47
Configuring Communication
7. Press the on-screen Reboot button to restart the panel and incorporate any changes.
FIG. 48 Protected Setup page
Before continuing, open NetLinx Studio 2.3. This program assists in developing a
System Number, Master IP/URL, and Master Port number. Refer to your NetLinx
Master’s instruction manuals for more information.
8. Obtain the System Number and Master IP Address from NetLinx Studio. This information
must be specific for the system used with the configured Modero panel.
9. Press the grey Front Setup Access button for 3 seconds to open the Setup page.
10. Press the Protected Setup button (located on the lower-left of the panel page) to open the
Protected Setup page.
11. Press the System Connection button (located on the Protected Setup page) to open the System
Connection page (FIG. 49) and begin configuring the communication settings on the panel to
match those of the target Master.
Modero
connection
information
NetLinx Master’s
connection
information
MAC Address
from panel is
factory set to a
unique address
FIG. 49 System Connection page
There are 2 possible Master Connection Types available: USB or Ethernet.
A USB connection type is a direct connection from the panel’s mini-USB port to a
corresponding USB port on the PC (acting as a Virtual Master).
An Ethernet connection type involves indirect communication from the panel to a
Master via an Ethernet connection to the network.
48
7" Modero Widescreen Touch Panels
Configuring Communication
It is recommended that firmware KIT files only be transferred over a direct
connection and only when the panel is connected to a power supply. If battery
power or wireless connection fails during a firmware upgrade, the panel flash
file system may become corrupted.
The mini-USB connector MUST be plugged into an already active panel before the
PC can recognize the connection and assign an appropriate USB driver. This driver is
part of both the NetLinx Studio and TPDesign4 software application installations.
Configuring and Using USB with a Virtual Master
NetLinx Studio can be setup to run a Virtual Master where the PC acts as the Master by supplying
its own IP Address for communication to the panel. The PC is first equipped with the USB driver,
the panel is then configured for USB communication, and then Studio is configured to act as the
Master.
For a personal computer to establish a connection to a Modero panel via USB, the target computer
must have the appropriate AMX USB driver installed. This installation is bundled into the latest
TPDesign4 (version 2.5 or higher) software setup process or can be downloaded independently
from the main Application Files page on www.amx.com.
Step 1: Setup the Panel and PC for USB Communication
1. If you do not currently have the latest version of TPDesign4, navigate to www.amx.com >
Tech Center > Downloadable Files > Application Files > NetLinx Design Tools section of
the website and locate the AMX USB Driver executable (AMX USBLAN Setup exe).
2. Download this executable file to a known location on your computer.
3. Launch the Setup.exe and follow the on-screen prompts to complete the installation.
Step 2: Confirm the Installation of the USB Driver on the PC
The first time each AMX touch panel is connected to the PC it is detected as a new hardware device
and the USBLAN driver becomes associated with it (panel specific). Each time thereafter the panel
is "recognized" as a unique USBLAN device and the association to the driver is done in the
background. When the panel is detected for the first time some user intervention is required during
the association between panel and driver.
1. After the installation of the USB driver has been completed, confirm the proper installation of
the large Type-A USB connector to the PC's USB port, and restart your machine.
If the panel is already powered, continue with steps 3.
The panel MUST be powered and configured for USB communication before
connecting the mini-USB connector to the panel’s Program Port.
2. Connect the terminal end of the PSN power cable to the 12 VDC power connector on the
rear/side of the panel and supply power.
3. After the CV7 panel powers-up, press and hold the grey Front Setup Access button
(for 3 seconds) to continue with the setup process and proceed to the Setup page.
4. Select Protected Setup > System Connection (located on the lower-left) to open the System
Connection page (FIG. 50).
7" Modero Widescreen Touch Panels
49
Configuring Communication
No connection is established until
the Virtual Master becomes
active within Studio
Red Connection Status icon indicates no connection to a Virtual
Master
Green Connection Status icon indicates communication to a Virtual
Master
FIG. 50 USB System Connection page - using a USB Connection Type
5. Toggle the blue Type field (from the Master Connection section) until the choice cycles to
USB. Refer to the System Connection Page section on page 109 for more information about the
fields on this page.
ALL fields are then greyed-out and read-only, but still display any previous network
information.
6. Press the Back button on the touch panel to return to the Protected Setup page.
7. Press the on-screen Reboot button to both save any changes and restart the panel. Remember
that the panel’s connection type must be set to USB prior to rebooting the panel and prior to
inserting the USB connector.
8. ONLY AFTER the unit displays the first panel page, THEN insert the mini-USB connector
into the Program Port on the panel. It may take a minute for the panel to detect the new
connection and send a signal to the PC (indicated by a green System Connection icon). If this is
your first time installing the USB driver, a USB driver installation popup window (FIG. 51)
appears on the PC.
FIG. 51 USB driver installation popup window
50
7" Modero Widescreen Touch Panels
Configuring Communication
This window notifies you that the panel has been detected by the PC as a USB-compliant
device and the PC is installing an appropriate USB driver to establish a proper
communication to the panel.
This driver was installed on your PC during the installation of the latest NetLinx Studio
and TPDesign4 software application installations. These applications should be
installed prior to setting up a USB connection to the panel.
The driver does not contain a Microsoft® digital signature and Windows® then informs
you of such.
9. Click Yes when told that a digital signature was not found. This action accepts the installation
of the new AMX USB driver. The panel is now configured to communicate directly with
the PC.
This process completes the association between driver and device.
Each time the same touch panel is connected to the computer the driver is
automatically loaded (using a unique name - example USB LAN LINK #1, #2).
Each time a different touch panel is connected to the computer, the previous
procedures will need to be repeated.
10. Navigate back to the System Connection page.
Step 3: Confirm and View the current AMX USB device connections
The USB driver information can be confirmed via two different methods:
Via the Control panel (previous steps 1 and 2) or
Via the Unplug or Eject Hardware icon from the Taskbar.
1. Navigate to Start > Settings > Control Panel > and double-click the System icon to launch
the System Properties dialog.
2. Select the Hardware tab and click on the Device Manager button to launch the Device
Manager dialog.
Within the Device Manager dialog, the AMX USBLAN device appears under Network
Adapters (FIG. 52) and has a unique name such as AMX USB LAN LINK #2. The
number changes depending on which recognized panel is currently connected.
3. Confirm that a new USB detection icon (FIG. 53) appears in the lower-right taskbar on the PC
display window.
4. Double-click on the icon to open the Unplug or Eject Hardware window and confirm the
AMX USB LAN LINK has been installed and is operating properly.
7" Modero Widescreen Touch Panels
51
Configuring Communication
USB connected touch
panel (showing the
recognized panel)
FIG. 52 Device Manager dialog showing USB device
A Virtual NetLinx Master (VNM) is used when the target panel is not connected to a
physical NetLinx Master. In this situation, the PC takes on the functions of a Master
via a Virtual NetLinx Master. This connection is made by either using the PC’s
Ethernet Address (via TCP/IP using a known PC’s IP Address as the Master) or
using a direct mini-USB connection to communicate directly to the panel.
5. Click the Properties button to view further information about the installed USB driver.
USB
detection
icon
FIG. 53 USB Properties windows
If there is a yellow exclamation point next to the AMX USB LAN LINK device (within
the hardware devices section of the Unplug or Eject Hardware window), stop and
close the USB operation. Reconnect the USB cable to the panel and repeat the setup
procedures. Refer to the Troubleshooting section on page 163 for more detailed
information.
To remove the USB driver association from a previously connected touch panel, you must
navigate back to the Device Manager, right-click on the panel’s USB driver (example AMX USB
LAN LINK #2) and select Uninstall from the context menu and then OK.
Once the system completes the removal of the device, the Device Manager window will
refresh, and the device will no longer appear.
52
7" Modero Widescreen Touch Panels
Configuring Communication
The next time this device is connected to the computer it will appear as a new hardware
device and will need to be associated again with the driver (refer to Step 2: Confirm the
Installation of the USB Driver on the PC section on page 49.
Step 4: Use the USB to Configure a Virtual Master (using NetLinx Studio)
When configuring your panel to communicate via USB with a Virtual Master (on your
PC), ONLY the USB connection option must be selected within the Type field. Since
this is a direct connection, the PC’s IP Address is not needed.
Before beginning:
1. Verify the panel has been configured to communicate via USB within the System Connection
page and that the USB driver has been properly configured. Refer to the previous section for
more information.
2. Launch NetLinx Studio 2.3 (default location is Start > Programs > AMX Control Disc >
NetLinx Studio > NetLinx Studio 2.3).
3. Select Settings > Master Communication Settings, from the Main menu to open the Master
Communication Settings dialog (FIG. 54).
IP Addresses of computer
(not needed as this is a direct
USB connection)
FIG. 54 Assigning Communication Settings for a Virtual Master
4. Click the Communications Settings button to open the Communications Settings dialog.
5. Click on the NetLinx Master radio button (from the Platform Selection section) to indicate
that you are working as a NetLinx Master.
6. Click on the Virtual Master radio box (from the Transport Connection Option section) to
indicate you are wanting to configure the PC to communicate directly with a panel. Everything
else such as the Authentication is greyed-out because you are not going through the Master’s
UI.
7. Click the Edit Settings button (on the Communications Settings dialog) to open the Virtual
NetLinx Master Settings dialog (FIG. 54).
8. From within this dialog enter the System number (default is 1).
7" Modero Widescreen Touch Panels
53
Configuring Communication
9. Click OK three times to close the open dialogs, save your settings, and return to the main
NetLinx Studio application.
10. Click the OnLine Tree tab in the Workspace window to view the devices on the Virtual
System. The default System value is one.
11. Right-click on the Empty Device Tree/System entry and select Refresh System to re-populate
the list.
The panel will not appear as a device below the virtual system number (in the Online Tree
tab) until both the system number used in step 7 for the VNM is entered into the Master
Connection section of the System Connection page and the panel is restarted.
The Connection status turns green after a few seconds to indicate an active USB
connection to the PC (Virtual Master). No Lock icon is displayed because this USB
connection is not secured (requiring a username/password).
If the G4 panel does not appear, refer to the Troubleshooting section on page 163 for
more information.
If a few minutes have gone by and the System Connection icon still does not turn green,
repeat the USB connection and Virtual Master setup procedures (outlined in this section).
Refreshing the System sends out a request to the panel to respond and completes the
communication (turning the System Connection icon green).
Step 5: Confirm and View the current AMX USB device connections
Use the CC-USB Type-A to Mini-B 5-wire programming cable (FG10-5965) to provide
communication between the mini-USB Program port on the touch panel and the PC. This method
of communication is used to transfer firmware KIT files and TPD4 touch panel files.
A mini-USB connection is only detected after it is installed onto an active
panel. Connection to a previously powered panel which then reboots, allows
the PC to detect the panel and assign an appropriate USB driver.
1. Verify this direct USB connection (Type-A on the panel to mini-USB on the panel) is
configured properly using the steps outlined in the previous two sections.
2. With the panel already configured for USB communication and the Virtual Master setup within
NetLinx Studio, its now time to verify the panel is ready to receive files.
3. Click the OnLine Tree tab in the Workspace window to view the devices on the Virtual
System. The default System value is one.
4. Right-click on the System entry (A in FIG. 55) and select Refresh System. This causes a
refresh of all project systems, establishes a new connection to the Virtual Master, and populates
the System list with devices on your particular system.
54
7" Modero Widescreen Touch Panels
Configuring Communication
FIG. 55 Using USB for Virtual Master communication
Secondary Connection Page - Wireless Access Overview
IP Routing
The behavior of the wireless routing is largely dependent on the wired network interface. Although
the panel can be connected to two networks simultaneously it may only have one gateway. If the
wired network was successfully set up and a gateway was obtained; then the default route for all
network traffic will be via the wired network. In the event that the wired network was not
configured, then the default route for all network traffic will be via the wireless network. The wired
network connection always takes priority.
As an example:
Imagine a panel connected to two networks A & B. A is the wired network and B is the
wireless network. If the Master controller is on either of these networks then it will be
reached. However if the Master controller is on a different network, C, then determining
which network interface (wired or wireless) that will be used is dependent on the
gateway.
Hot Swapping
Hot swapping is not an issue on these panels as the card is installed within the unit and cannot be
removed without first removing the housing.
In the case of DHCP, there must be a DHCP server accessible before the fields are populated.
If the SSID (Network Name) and WEP fields have not previously been configured, the
Secondary Connection page will not work until the panel is rebooted.
Ethernet Communication from the panel can be direct (using an Ethernet cable) or indirect (through
the NXA-WC80211B/CF AMX Wireless Card communicating to a Wireless Access Point (WAP)
such as the NXA-WAP200G). In determining the Ethernet method of communication, the panel
will always default first to the direct Ethernet communication. If no direct connection is detected,
the panel will first check to see if there is an installed wireless interface card and then communicate
to the WAP using the Wireless Settings assigned within the Secondary Connection page. The WAP
7" Modero Widescreen Touch Panels
55
Configuring Communication
communication parameters must match those of the pre-installed wireless interface card installed
within the panel. The CV7 touch panels allow users to connect to a wireless network through their
use of the optional AMX 802.11b wireless interface card. This internal card transmits data using
the 802.11b signals at 2.4 GHz. Before beginning, there are several concepts that should be
explained:
Wireless Access Points are the cornerstone of any wireless network. A Wireless Access
Point acts as a bridge between a wired and wireless network. It aggregates the traffic
from all the wireless clients and forwards it down the network to the switch or router.
One Wireless Access Point may be all you need. However, you could need more Wireless
Access Points depending on either how large your installation is, how it is laid out, and
how it is constructed.
802.11b/2.4 GHz vs. 802.11a/5 GHz are the two major WLAN standards and both
operate using radio frequency (RF) technology. Together the two standards are together
called Wi-Fi and operate in frequency bands of 2.4 GHz and 5 GHz respectively.
The 802.11b specification was the first to be finalized and reach the marketplace and at
this time is the only specification supported by the Modero line of products. The actual
throughput you can expect to obtain from an 802.11b network will typically be between
4 and 5 Mbps.
When indoors, 802.11b signals can travel as far as 150 meters (492 feet). The outdoor
802.11b range is over three times greater; 500 meters (1640 feet, or nearly 1/3 of a mile).
At either of these extreme ranges, the bandwidth available is at least 1Mbps. To operate
in its maximum bandwidth mode of 11 Mbps, the distance indoors can be no more than
50 meters (164 feet); outdoors it should be 250 meters (820 feet).
Because of the higher frequency (and thus shorter wavelength) that they use, 802.11a
signals have a much tougher time penetrating solid objects like walls, floors, and ceilings.
As a result, the price for 802.11a's higher speed is not only shorter in range but also a
weaker and less consistent signal.
Wireless Equivalent Privacy (WEP) Security is a method by which WLANs protect
wireless data streams. A data stream encrypted with WEP can still be intercepted or
eavesdropped upon, but the encryption makes the data unintelligible to the interloper. The
strength of WEP is measured by the length of the key used to encrypt the data. The longer
the key, the harder it is to crack.
802.11b implementations provided 40-bit and 104-bit WEP keys. This is known
respectively as 64-bit and 128-bit WEP encryption. 64-bit is generally not regarded as
adequate security protection. Both key lengths are supported by the Modero product line.
Whichever level of WEP you use, it's crucial to use identical settings (CASE
SENSITIVE)--the key length, and the key itself-- on all devices. Only devices with
common WEP settings will be able to communicate. Similarly, if one device has WEP
enabled and another doesn't, they won't be able to talk to each other.
Although the calculations required to encrypt data with WEP can impact the performance
of your wireless network, it's generally seen only when running benchmarks, and not
large enough to be noticeable in the course of normal network usage.
56
7" Modero Widescreen Touch Panels
Configuring Communication
Configuring a Wireless Network Access
When working with a wireless card, the first step is to configure wireless communication
parameters within the Secondary Connection page. This page only configures the card to
communicate to a target WAP (such as the NXA-WAP200G), it is still necessary to tell the panel
which Master it should be communicating with. This "pointing to a Master" is done via the
System Connection page where you configure the IP Address, System Number and
Username/Password information assigned to the target Master.
Step 1: Configure the Panel’s Wireless IP Settings
The first step to successfully setting up your wireless card is to configure the IP Settings section on
the Secondary Connection page. The section configures the communication parameters from the
Modero panel to the web.
Wireless communication using a DHCP Address
1. Press the Protected Setup button (located on the lower-left of the panel page) to open the
Protected Setup page and display an on-screen keypad.
2. Enter 1988 into the Keypad’s password field and press Done when finished.
3. Press the Secondary Connection button (located on the lower-left) to open the Secondary
Connection page. Wireless communication is set within the IP Settings section of this page
(FIG. 56).
4. Toggle the DHCP/Static field (from the IP Settings section) until the choice cycles to DHCP.
This action causes all fields in the IP Settings section (other than Host Name) to be greyed-out.
DHCP will register the unique MAC Address (factory assigned) on the panel and
once the communication setup process is complete, assign IP Address, Subnet
Mask, and Gateway values from the DHCP Server.
5. Press the optional Host Name field to open a Keyboard and enter the Host Name information.
Modero
connection
IP info.
FIG. 56 Secondary Connection page (IP Settings section)
6. Press Done after you are finished assigning the alpha-numeric string of the host name.
7. Do not alter any of these remaining greyed-out fields in the IP Settings section. Once the panel
is rebooted, these values are obtained by the unit and displayed in the DNS fields after
power-up.
7" Modero Widescreen Touch Panels
57
Configuring Communication
This information can be found in either the Workspace - System name > Define
Device section of your code (that defines the properties for your panel), or in the
Device Addressing/Network Addresses section of the Tools > NetLinx Diagnostics
dialog.
8. Setup the security and communication parameters between the wireless card and the target
WAP by configuring the Wireless Settings section on this page. Refer to Step 2: Configure the
Card’s Wireless Security Settings section on page 59 for detailed procedures to setup either a
secure or unsecure connection.
Wireless communication using a Static IP Address
1. Press the Protected Setup button (located on the lower-left of the panel page) to open the
Protected Setup page and display an on-screen keypad.
2. Enter 1988 into the Keypad’s password field and press Done when finished.
3. Press the Secondary Connection button (located on the lower-left) to open the Secondary
Connection page. Wireless communication is set within the IP Settings section of this page
(FIG. 56).
Check with your System Administrator for a pre-reserved Static IP Address assigned
to the panel. This address must be obtained before Static assignment of the panel
continues.
4. Toggle the DHCP/Static field (from the IP Settings section) until the choice cycles to Static.
The IP Address, Subnet Mask, and Gateway fields then become user-editable (red).
5. Press the IP Address field to open a Keyboard and enter the Static IP Address (provided by
your System Administrator).
6. Press Done after you are finished entering the IP information.
7. Repeat the same process for the Subnet Mask and Gateway fields.
8. Press the optional Host Name field to open the Keyboard and enter the Host Name information.
9. Press Done after you are finished assigning the alpha-numeric string of the host name.
10. Press the Primary DNS field to open a Keyboard, enter the Primary DNS Address (provided by
your System Administrator) and press Done when compete. Repeat this process for the
Secondary DNS field.
11. Press the Domain field to open a Keyboard, enter the resolvable domain Address (this is
provided by your System Administrator and equates to a unique Internet name for the panel),
and press Done when complete.
12. Setup the security and communication parameters between the wireless card and the target
WAP by configuring the Wireless Settings section on this page. Refer to the following section
for detailed procedures to setup either a secure or unsecure connection.
58
7" Modero Widescreen Touch Panels
Configuring Communication
Step 2: Configure the Card’s Wireless Security Settings
The second step to successfully setting up your wireless card is to configure the Wireless Settings
section of the Secondary Connection page. The section configures both the communication and
security parameters from the internal wireless card to the WAP. The procedures outlined within the
following sections use an NXA-WAP200G and the target WAP.
Once you have completed setting up the wireless card parameters, you must then
navigate to the System Connection page and configure the communication
parameters for the target Master. Until those parameters are configured, your
Connection Status icon will remain red (indicating that there is no current connection
to a Master).
Configuring the Modero’s wireless card for unsecured access to a WAP200G
Prior to beginning the configuration of the wireless settings, verify that the panel has
been upgraded to a wireless panel via the installation of the NXA-WC80211B/CF
wireless interface card.
1. Power-down the Modero unit and follow the wireless card installation procedures outlined in
the Installation of the Wireless Card (Table Top Panel) section on page 15.
2. Power-up the panel (this allows it to detect the card).
3. Press the Protected Setup button (located on the lower-left of the panel page) to open the
Protected Setup page and display an on-screen keypad.
4. Enter 1988 into the Keypad’s password field and press Done when finished.
5. Press the Secondary Connection button (located on the lower-left) to open the Secondary
Connection page.
6. From within the Wireless Settings section of the Secondary Connection page, touch the
Network Name (SSID) field (FIG. 57).
Wireless card
settings
FIG. 57 Secondary Connection page (showing default values)
7. From the Service Set Identifier keyboard, enter the SSID name used on your target Wireless
Access Point (case sensitive).
The card should be given the SSID used by the target WAP. If this field is left blank, the
unit will attempt to connect to the first available WAP. By default, all WAP200Gs use
AMX as their assigned SSID value.
7" Modero Widescreen Touch Panels
59
Configuring Communication
One of the most common problems associated with connection to a WAP arise because
the SSID was not entered properly. You must maintain the same case when entering the
SSID information. ABC is not the same as Abc.
8. Toggle the Authentication field to an Open System (default).
Open System Authentication allows any device to join the network if the panel’s SSID
matches the WAP’s SSID.
9. Toggle the Encryption field until it reads Clear Text (default).
The remaining Wireless Settings fields are then greyed-out and become read-only. All
NXA-WAP200Gs are factory-shipped as an unsecured WAP with no WEP
encryption. The WAP200G initial Status page will display the status of both the WEP
and WPA (both disabled).
10. Verify the fields in the IP Settings section have been properly configured. Refer to Step 1:
Configure the Panel’s Wireless IP Settings section on page 57 for detailed information.
11. Press the Back button to navigate to the Protected Setup page and press the on-screen Reboot
button to both save any changes and restart the panel. Remember that you will need to
navigate to the System Connection page and configure the connection to a target Master.
12. After the panel restarts, return to the Secondary Connection page to verify the Link Quality
and Signal Strength:
The bargraphs have been replaced with descriptions: None, Poor, Fair, Good, Very
Good, and Excellent (FIG. 57).
The signal strength field should provide some descriptive text regarding the strength
of the connection to a Wireless Access Point. If there is no signal or no IP Address
displayed; configuration of your network could be required.
Refer to the NXA-WAP200G Instruction Manual for more detailed setup and configuration
procedures.
Configuring the Modero’s wireless card for secured access to a WAP200G
After logging into the WAP200G, the default Status page appears within the web browser. These
read-only values are "pulled" from some of the other user-configurable Configuration Utility pages.
By default, wireless Modero panels are configured for unsecured communication to a Wireless
Access Point. To properly setup both the WAP200G and panel for secure communication, you must
first prepare the Modero panel and then use the information provided to fill out the fields within the
WAP’s browser-based Basic Wireless Configuration page.
Since the code key generator on Modero panels use the same key generation formula, all panels
will generate identical keys for the same Passphrase. The generators used on WAPs will not
produce the same key as the Modero generator even if you use the same Passphrase. This is why
we recommend creating the Current Key FIRST on the Modero and then entering that
information into the appropriate WAP200G fields.
1. Power-down the Modero unit and follow the wireless card installation procedures outlined in
the Installation of the Wireless Card (Table Top Panel) section on page 15.
When configuring touch panels for wireless communication, verify that no Ethernet
connector is installed within the panel before the unit is power cycled.
60
7" Modero Widescreen Touch Panels
Configuring Communication
2. Power-up the panel (this allows it to detect the card).
3. Press the Protected Setup button (located on the lower-left of the panel page) to open the
Protected Setup page and display an on-screen keypad.
4. Enter 1988 into the Keypad’s password field and press Done when finished.
5. Press the Secondary Connection button (located on the lower-left) to open the Secondary
Connection page.
6. Locate the Wireless Settings section of the Secondary Connection page (FIG. 58).
SSID field
Wireless card communication
settings (for use with a target WAP)
Changes on this page take
effect after using the BACK
button to return to the
previous page
FIG. 58 Secondary Connection page (Wireless Settings section)
You must first take the SSID name, Current Key string value, and panel MAC Address
information and then later enter it into the appropriate WAP dialog fields in order to
"sync-up" the secure connection. These values must be identically reproduced on the
target WAP.
7. Touch the Network Name (SSID) field and from the Service Set Identifier keyboard, enter the
SSID name you will be using on your target Wireless Access Point (case sensitive).
The card should be given the SSID used by the target WAP. If this field is left blank, the
unit will attempt to connect to the first available WAP. By default, all WAP200Gs use
AMX as their assigned SSID value.
One of the most common problems associated with connection to a WAP arise because
the SSID was not entered properly. You must maintain the same case when entering the
SSID information. ABC is not the same as Abc.
The alpha-numeric string is by default AMX but can later be changed to any 32-character
entry. This string must be duplicated within the Network Name (SSID) field on the WAP.
As an example, if you use TECHPUBS as your SSID, you must match this word and
the case within both the Network Name (SSID) field on the touch panel’s Network Name
SSID field and on the WAP’s Basic Wireless Configuration page.
8. Leave the Authentication field reading Open System (default).
Open System Authentication allows any device to join the network if the panel’s SSID
matches the WAP’s SSID. An Open System is recommended for communication
between Modero panels and an NXA-WAP200G.
7" Modero Widescreen Touch Panels
61
Configuring Communication
Shared Key Authentication requires that the panel and the Wireless Access Point have
the same WEP Key to authenticate.
9. Toggle the Encryption field (FIG. 58) until it reads WEP64 or WEP128. The 64/128 selection
reflects the bit-level of encryption security. This WEP encryption level must match the
encryption level being used on the WAP
WEP will not work unless the same Default Key is set on both the panel and the
Wireless Access Point.
For example: if you have your Wireless Access Point set to default key 4 (which
was 01:02:03:04:05), you must set the panel’s key 4 to 01:02:03:04:05.
10. Toggle the Default Key field until the you’ve chosen a WEP Key value (from 1- 4) that
matches what you’ll be using on your target WAP200G.
These WEP Key identifier values must match for both devices.
11. With the proper WEP Key value displayed, press the Generate button to launch the WEP
Passphrase keyboard.
If you are wanting to have your target WAP (other than a 200G) generate the Current Key Do not press the Generate button and continue with Step 14.
This keyboard allows you to enter a Passphrase (such as AMXPanel) and then
AUTOMATICALLY generate a WEP key which is compatible only among Modero
panels.
The code key generator on Modero panels use the same key generation formula.
Therefore, this same Passphrase generates identical keys when done on any Modero
because they all use the same Modero-specific generator. The Passphrase generator
is case sensitive.
12. Within this on-screen WEP Passphrase keyboard (FIG. 59), enter a character string or word
(such as AMXPanel) and press Done when you have finished.
FIG. 59 WEP Passphrase Keyboard
As an example, enter the word AMXPanel using a 128-bit hex digit encryption. After
pressing Done, the on-screen Current Key field displays a long string of characters
(separated by colons) which represents the encryption key equivalent to the word
AMXPanel.
62
7" Modero Widescreen Touch Panels
Configuring Communication
This series of hex digits (26 hex digits for a 128-bit encryption key) should be
entered as the Current Key into both the WAP and onto other communicating
Modero panels by using the WEP Key dialog (FIG. 60).
FIG. 60 WEP Key # Keyboard
13. Write down this Current Key string value for later entry into your WAP’s WEP Key field
(typically entered without colons) and into the communicating panel’s Current Key field
(FIG. 58).
14. If you are entering a Current Key generated either by your target WAP or another
Modero panel, within the WEP Keys section, touch the Key # button to launch the WEP Key #
keyboard (FIG. 60), enter the characters and press Done when finished.
This Key value corresponds to the Default WEP Key number used on the Wireless Access
Point and selected in the Default Key field described in the previous step.
If your target Wireless Access Point does not support passphrase key
generation and has previously been setup with a manually entered WEP KEY,
you must manually enter that same WEP key on your panel.
15. Verify the fields within the IP Settings section have been properly configured. Refer to Step 1:
Configure the Panel’s Wireless IP Settings section on page 57 for detailed information.
16. Press the Back button to navigate to the Protected Setup page and press the on-screen Reboot
button to both save any changes and restart the panel. Remember that you will need to
navigate to the System Connection page and configure the connection to a target Master.
17. After the panel restarts, return to the Secondary Connection page to verify the Link Quality
and Signal Strength:
The bargraphs have been replaced with descriptions: None, Poor, Fair, Good, Very
Good, and Excellent.
The signal strength field provides some descriptive text regarding the strength of the
connection to a Wireless Access Point. If there is no signal or no IP Address
displayed; configuration of your network could be required.
Refer to the NXA-WAP200G Instruction Manual for more detailed setup and configuration
procedures.
7" Modero Widescreen Touch Panels
63
Configuring Communication
Configuring multiple wireless Moderos to communicate to a target WAP200G
1. For each communicating touch panel, complete all of the steps outlined within the previous
Configuring the Modero’s wireless card for secured access to a WAP200G section on page 60.
2. Navigate back to the Wireless/Secondary Connection page on each panel.
3. Verify that all communicating Modero panels are using the same SSID, encryption level,
Default Key #, and an identical Current Key value.
As an example, all panels should be set to Default Key #1 and be using aa:bb:cc..as the
Current Key string value. This same Key value and Current Key string should be used on
the target WAP.
4. Repeat steps 1 - 3 on each panel. Using the same passphrase, generates the same key for all
communicating Modero panels.
Configuring a Wired Ethernet Connection
It is necessary to tell the panel which Master it should be communicating with. This "pointing
to a Master" is done via the System Connection page where you configure the IP Address, System
Number and Username/Password information assigned to the target Master. If you have previously
established a wireless connection to the Internet you must still navigate to the System Connection
page and configure the communication parameters for the target Master. Until those parameters are
configured, your Connection Status icon will remain red (indicating there is no current connection
to a Master).
If you have previously configured an internal wireless card for communication to the
Internet, you do not need to configure the panel’s IP Settings fields and can skip the
following Step 1.
Step1: Configure the Panel’s Wired IP Settings
There are only two available methods of communicating a target Master over the Internet: Wireless
(via an internal card) or Wired (direct Ethernet connection). If you are not using an internal wireless
card, you can only configure the connection parameters through the System Connection page. This
type of communication can be established either via either a Dynamic IP Address (DHCP) or via a
pre-reserved Static IP Address (typically provided by your System Administrator).
IP Settings section - Configuring a DHCP Address over Ethernet
1. Select Protected Setup > System Connection (located on the lower-left) to open the System
Connection page.
2. Locate the IP Settings section of this page.
Even though the Host, Gateway, Primary DNS, Secondary DNS, and Domain fields
appear on the two separate System Connection and Secondary Connection pages;
the information populating these fields is identical.
If the information within one of these fields is altered, the change is reflected on both
pages within the altered field.
Example: Domain is altered on Secondary Connection page, the value is then also
changed within the Domain field of the System Connection page.
3. Toggle the DHCP/Static field (from the IP Settings section) until the choice cycles to DHCP.
64
7" Modero Widescreen Touch Panels
Configuring Communication
DHCP will register the unique MAC Address (factory assigned) on the panel and
once the communication setup process is complete, reserve an IP Address, Subnet
Mask, and Gateway values from the DHCP Server.
4. Press the optional Host Name field to open a Keyboard and enter the Host Name information.
5. Press Done after you are finished assigning the alpha-numeric string of the host name.
6. Do not alter any of the remaining greyed-out fields in the IP Settings section. Once the panel is
rebooted, these values are obtained by the unit and displayed in the DNS fields after power-up.
This information can be found in either the: Workspace- System name > Define
Device section of your code (that defines the properties for your panel), or in the
Device Addressing/Network Addresses in the Tools > NetLinx Diagnostics dialog.
7. Press the Back button to return to the Protected Setup page.
8. Press the on-screen Reboot button to both save any changes and restart the panel.
IP Settings section - Configuring a Static IP Address over Ethernet
1. Select Protected Setup > System Connection (located on the lower-left) to open the System
Connection page.
2. Locate the IP Settings section of this page.
Check with your System Administrator for a pre-reserved Static IP Address assigned
to the panel. This address must be obtained before Static assignment of the panel
continues.
3. Toggle the DHCP/Static field (from the IP Settings section) until the choice cycles to Static.
4. Press the IP Address field to open a Keyboard and enter the Static IP Address (provided by
your System Administrator).
5. Press Done after you are finished entering the IP information.
6. Repeat the same process for the Subnet Mask and Gateway fields.
7. Press the optional Host Name field to open the Keyboard and enter the Host Name information.
8. Press Done after you are finished assigning the alpha-numeric string of the host name.
9. Press the Primary DNS field to open a Keyboard, enter the Primary DNS Address (provided by
your System Administrator) and press Done when compete. Repeat this process for the
Secondary DNS field.
10. Press the Domain field to open a Keyboard, enter the resolvable domain Address (this is
provided by your System Administrator and equates to a unique Internet name for the panel),
and press Done when complete.
11. Navigate to the Master Connection section of this page to begin configuring the
communication parameters for the target Master.
7" Modero Widescreen Touch Panels
65
Configuring Communication
Step 2: Choose a Master Connection Mode Setting
There are three Ethernet MODE settings used in the Master Connection section of the System
Connection page. URL is the most common method.
Master Connection MODE options:
• URL (Uniform Resource Locator) is the address that defines the route to a file on the Web or
any other Internet facility.
In this system, the panel acts as a "Client" and the Master acts as a Server (in that Clients attach
to it).
• LISTEN sets the Modero panel to "listen" for broadcasts from the Master (using the panel IP from
its URL list). In this system, the panel acts as a "Server" (in that Clients attach to it) and the
Master acts as a "Client".
• AUTO is used to instruct the Modero to search for a Master that uses the same System Number
(assigned within the Master Connection section) and resides on the same Subnet as itself. In this
case, the Master has its UDP feature enabled.
This UDP (User Datagram Protocol) is a protocol within the TCP/IP protocol suite that is used in
place of TCP when a reliable delivery is not required.
This UDP enabling is done through a Telnet session on the Master. Refer to the particular NetLinx
Master manual for more detailed information.
Step 3: Configure an Ethernet Connection Type
When using Ethernet as your communication method, the NetLinx Master must first
be setup with either a Static IP or DHCP Address obtained from either NetLinx Studio
or your System Administrator.
Before beginning:
1. Verify the panel has been configured to communicate either through an Ethernet cable
(connected from either the panel to a valid Ethernet Hub) or to a wirelessly to the Wireless
Access Point (WAP).
Before commencing, verify you are using the latest NetLinx Master firmware.
2. Verify that the NetLinx Master is receiving power and is communicating via an Ethernet
connection with the PC running NetLinx Studio.
3. Connect the terminal end of the PSN power cable to the 12 VDC power connector on the
rear/side of the touch panel.
4. Verify the green Ethernet LED (from the rear Ethernet port on the Master) is illuminated
(indicating a proper connection).
5. Verify the yellow LED (from the rear Ethernet port on the Master) is blinking (indicating
communication).
6. After the panel powers-up, press and hold the grey Front Setup Access button (for 3 seconds)
to proceed to the Setup page.
7. Select Protected Setup > System Connection (located on the lower-left) to open the System
Connection page (FIG. 61).
66
7" Modero Widescreen Touch Panels
Configuring Communication
Obtained
from
NetLinx
Master
FIG. 61 System Connection page
Master Connection section - Virtual Master communication over Ethernet
When configuring your panel to communicate with a Virtual Master (on your PC) via
Ethernet, the Master IP/URL field must be configured to match the IP Address of the
PC and make sure to use the Virtual System value assigned to the Virtual Master
within NetLinx Studio.
Before beginning:
1. Verify the panel has been configured to communicate either through an Ethernet cable
(connected from either the panel to a valid Ethernet Hub) or wireless to the Wireless Access
Point.
2. Launch NetLinx Studio 2.3 (default location is Start > Programs > AMX Control Disc >
NetLinx Studio > NetLinx Studio 2.3).
3. Select Settings > Master Communication Settings, from the Main menu to open the Master
Communication Settings dialog (FIG. 62).
Enter this IP
into the
Master IP/URL
field on the
System Connection
page
IP Addresses of computer
(also obtained by using the
Start > Run > cmd command)
FIG. 62 Assigning Communication Settings and TCP/IP Settings for a Virtual Master
4. Click the Communications Settings button to open the Communications Settings dialog.
7" Modero Widescreen Touch Panels
67
Configuring Communication
5. Click on the NetLinx Master radio button (from the Platform Selection section) to indicate
that you are working as a NetLinx Master.
6. Click on the Virtual Master radio box (from the Transport Connection Option section) to
indicate you are wanting to configure the PC to communicate with a panel. Everything else
such as the Authentication is greyed-out because you are not going through the Master’s UI.
7. Click the Edit Settings button (on the Communications Settings dialog) to open the Virtual
NetLinx Master Settings dialog (FIG. 62).
8. From within this dialog enter the System number (default is 1) and note the IP Address of the
target PC being used as the Virtual Master. This IP Address can also be obtained by following
these procedures:
On your PC, click Start > Run to open the Run dialog.
Enter cmd into the Open field and click OK to open the command DOS prompt.
From the C:\> command line, enter ipconfig to display the IP Address of the PC. This
information is entered into the Master IP/URL field on the panel.
9. Click OK three times to close the open dialogs, save your settings, and return to the main
NetLinx Studio application.
10. Click the OnLine Tree tab in the Workspace window to view the devices on the Virtual
System. The default System value is one.
11. Right-click on the Empty Device Tree/System entry and select Refresh System to re-populate
the list.
12. Power-up your panel and press and hold the grey Front Setup Access button (for 3 seconds) to
continue with the setup process and proceed to the Setup page.
13. Select Protected Setup > System Connection (located on the lower-left) to open the System
Connection page (FIG. 63).
The System Number is
assigned to the Master
within the AMX
software application
(these must match)
Enter the IP Address
information of the PC
used as a Virtual
Master
When using a Virtual Master,
there is no need to enter a
username and/or password
FIG. 63 Sample System Connection page (for Virtual Master communication)
14. Press the blue Type field (from the Master Connection section) until the choice cycles to the
word Ethernet.
15. Press the Mode field until the choice cycles to the word URL.
68
7" Modero Widescreen Touch Panels
Configuring Communication
By selecting URL, the System Number field becomes read-only (grey) because the panel
pulls this value directly from the communicating target Master (virtual or not). A Virtual
Master system value can be set within the active AMX software applications such as:
NetLinx Studio, TPD4, or IREdit.
16. Press the Master IP/URL field to open a Keyboard and enter the IP Address of the PC used as
the Virtual Master.
17. Click Done to accept the new value and return to the System Connection page.
18. Do not alter the Master Port Number value (this is the default value used by NetLinx).
19. Press the Back button to open the Protected Setup page.
20. Press the on-screen Reboot button to both save any changes and restart the panel.
Master Connection section - NetLinx Master Ethernet IP Address - URL Mode
In this mode, enter the System Number (zero for an unknown System Number) and the IP/URL of
the Master (Master Port Number is defaulted to 1319).
1. Press the blue Type field (from the Master Connection section) until the choice cycles to the
word Ethernet (FIG. 63). Refer to the System Connection Page section on page 109 for more
information about the fields on this page.
2. Press the Mode field until the choice cycles to the word URL.
By selecting URL, the System Number field becomes read-only (grey) because the panel
pulls this value directly from the communicating target Master (virtual or not). A Virtual
Master system value can be set within the active AMX software applications such as:
NetLinx Studio, TPD4, or IREdit.
If the panel does not appear within the OnLine Tree tab of the Workspace window of
NetLinx Studio, check to make sure that the NetLinx Master System Number (from
within the Device Addressing dialog) is correctly assigned.
3. Press the Master IP/URL field to open a Keyboard and enter the Master IP Address (obtained
from the Diagnostics - Networking Address dialog of the NetLinx Studio application).
4. Click Done to accept the new value and return to the System Connection page.
5. Do not alter the Master Port Number value (this is the default value used by NetLinx).
6. Enter a username and password (into their respective fields) if the target Master has been
previously secured.
7. Press the Back button to open the Protected Setup page.
8. Press the on-screen Reboot button to both save any changes and restart the panel.
7" Modero Widescreen Touch Panels
69
Configuring Communication
Master Connection section - NetLinx Master Ethernet IP Address - Listen Mode
In this mode, you must add the Modero panel IP Address into the URL List of the Master (using
NetLinx Studio). This mode sets the Modero panel to "listen" for broadcasts from the Master (using
the panel IP from its URL list).
1. Obtain either a Static IP for the Modero panel (from your System Administrator) or a DHCP
Address from the IP Settings of the System Connection page.
The DHCP/Static field (in the IP Settings section of the System Connection page) must
be set to DHCP to get Dynamic IP information for the panel.
Press the on-screen Reboot (from the Protected Setup page) to both save any changes and
restart the panel.
After power-up, press the grey Front Setup Access button for 3 seconds to access the
Setup page.
Navigate to the Setup > Protected Setup > System Connection page and note the newly
obtained Dynamic IP Address information from the IP Settings section. This information
is then entered into the URL List for the connected NetLinx Master.
2. Toggle the Type field until Ethernet is selected (from the Master Connection section of the
System Connection page).
3. Press the Mode field (to set the connection Mode) until the choice cycles to the word Listen.
The System Number and Master IP/URL fields are then greyed-out.
4. Enter a username and password (into their respective fields) if the target Master has been
previously secured.
5. Select the OnLine Tree tab from the Workspace window.
6. Select Diagnostics > URL Listing from the Main menu (FIG. 64).
System Address
reflects the value
set in the Device
Addressing tab
Used to obtain an
existing URL
List from Master
Used to set the
URL List
on Master
FIG. 64 URL List dialog
7. Enter the System and Device number for the specific Master associated with your panel (as
seen in the OnLine Tree tab).
8. Click Add and enter the IP Address of the Modero touch panel into the Add URL dialog.
9. Click OK to enter your IP Address and add it to the list.
10. Click Done once you are finished adding your panel information to the list.
70
7" Modero Widescreen Touch Panels
Configuring Communication
11. Press the on-screen Reboot button to save any changes and restart the panel.
Master Connection section - NetLinx Master Ethernet IP Address - Auto Mode
In this mode, enter the System Number of the NetLinx Master. This mode instructs the Modero to
search for a Master that uses the same System Number (assigned within the Master Connection
section) and resides on the same Subnet as itself.
1. Toggle the blue Type field until Ethernet is selected (from the Master Connection section of
the System Connection page).
2. Press the Mode field until the choice cycles to the word Auto.
3. Press the System Number field to launch a Keypad and enter the value for the system number of
the NetLinx Master. This value can be obtained from the NetLinx Studio program > OnLine
Tree of the Workspace window.
4. Do not alter the IP Settings section, of the System Connection page, as these fields are not
applicable to this connection mode.
5. Enter a username and password (into their respective fields) if the target Master has been
previously secured.
6. Press the on-screen Reboot button to both save any changes and restart the panel.
7. Press the grey Front Setup Access button for 3 seconds to open the Setup page and confirm
there is an active connection.
The NetLinx Master and the Modero panel must both be on the same Subnet.
Using G4 Web Control to Interact with a G4 Panel
The G4 Web Control feature allows you to use a PC to interact with a G4 enabled panel via the web.
This feature works in tandem with the new browser-capable NetLinx Security firmware update
(build 300 or higher). G4 Web Control is only available with the latest Modero panel firmware.
Refer to the G4 Web Control Page section on page 100 for more detailed field information.
Verify your NetLinx Master (ME260/64 or NI-Series) has been installed with the latest
firmware KIT file from www.amx.com. Refer to your NetLinx Master instruction
manual for more detailed information on the use of the new web-based NetLinx
Security.
1. Press the grey Front Setup Access button for 3 seconds to open the Setup page.
2. Press the Protected Setup button (located on the lower-left of the panel page) to open the
Protected Setup page and display an on-screen keypad.
3. Enter 1988 into the Keypad’s password field (1988 is the default password).
Clearing Password #5, from the initial Password Setup page, removes the need for
you to enter the default password before accessing the Protected Setup page.
4. Press Done when finished.
5. Press the G4 WebControl button to open the G4 Web Control page (FIG. 65).
7" Modero Widescreen Touch Panels
71
Configuring Communication
FIG. 65 G4 Web Control page
6. Press the Enable/Enabled button until it toggles to Enabled (light blue color).
7. The Network Interface Select field is read-only and displays the method of communication to
the web. Verify you have selected the proper interface connection as this field does not
auto-detect the connection type being used (see below).
Wired is used when a direct Ethernet connection is being used for communication to the
web. This is the default setting if either no wireless interface card is detected or if both an
Ethernet and wireless card connection is detected by the panel.
Wireless is used when a wireless card is detected within the internal card slot. This
method provides an indirect communication to the web via a pre-configured Wireless
Access Point.
8. Press the Web Control Name field to open the Web Name keyboard.
9. From the Web Name keyboard, enter a unique alpha-numeric string to identify this panel. This
information is used by the NetLinx Security Web Server to display on-screen links to the panel.
The on-screen links use the IP Address of the panel and not the name for communication
(FIG. 66).
FIG. 66 Sample relationship between G4 Web Control and NetLinx Security-Mange WebControls window
10. Press Done after you are finished assigning the alpha-numeric string for the Web Control
name.
11. Press the Web Control Password field to open the Web Password keyboard.
72
7" Modero Widescreen Touch Panels
Configuring Communication
12. From the Web Password keyboard, enter a unique alpha-numeric string to be assigned as the
G4 Authentication session password associated with VNC web access of this panel.
13. Press Done after you are finished assigning the alpha-numeric string for the Web Control
password.
14. Press the Web Control Port field to open the Web Port Number keypad.
15. Within the keypad, enter a unique numeric value to be assigned to the port the VNC Web
Server is running on. The default value is 5900.
16. Press Done when you are finished entering the value. The remaining fields within the G4 Web
Control Settings section of this page are read-only and cannot be altered.
17. Press the Up/Down arrows on either sides of the G4 Web Control Timeout field to increase or
decrease the amount of time the panel can remain idle (no cursor movements) before the
session is closed and the user is disconnected.
18. Press the Back button to open the Protected Setup page.
19. Press the on-screen Reboot button to save any changes and restart the panel.
Verify your NetLinx Master’s IP Address and System Number have been properly
entered into the Master Connection section of the System Connection page.
Accessing the NetLinx Master via an IP Address
Refer to your particular NetLinx Master’s instruction manual for detailed information on how to
download the latest firmware (build 300 or higher) from www.amx.com. This firmware build
enables SSL security and disables the ability to alter the Master security properties via a TELNET
session.
Once the Master’s IP Address has been set through NetLinx Studio:
1. Launch your web browser.
2. Enter the IP Address of the target NetLinx Master (with either http or https) into your web
browser’s Address field.
3. Click OK to accept the AMX SSL certificate (if SSL is enabled).
4. Enter a valid username and password into the fields within the Login dialog.
5. Press the Enter key on your keyboard to begin the communication process between the target
Master and your PC.
6. The first window displayed (FIG. 67) is accessed by clicking on the Manage connections link.
Once activated, this page displays links to G4 panels running the latest G4 Web Control
feature.
7" Modero Widescreen Touch Panels
73
Configuring Communication
Compatible
devices field
(showing G4
WebControl links)
G4 panels
Compression
Options
FIG. 67 WebControls window (populated with panels)
Using your NetLinx Master to Control the G4 panel
Once the Master’s IP Address has been set through NetLinx Studio (version 2.3 or higher):
1. Follow the procedures mentioned above to communicate to the target NetLinx Master through
an IP Address.
2. Enter a valid user name and password into the fields within the Login dialog.
3. Click OK to enter the information and proceed to the Master’s Manage WebControls window.
4. Press the Enter key on your keyboard to begin the communication process between the target
Master and your PC.
If a Security Alert window appears on your computer screen, refer to the specific NetLinx Master
instruction manual for detailed information regarding this popup window. These steps are based on
a Master with proper security and SSL encryption enabled.
5. Click on the G4 panel name link associated with the target panel. A secondary web browser
window then appears on the screen (FIG. 68).
FIG. 68 Web Control VNC installation and Password entry screens
74
7" Modero Widescreen Touch Panels
Configuring Communication
6. Click Yes from the Security Warning popup window to agree to the installation of the G4 Web
Control application on your computer. This application contains the necessary Active X and
VNC client applications necessary to properly view and control the panel pages from your
computer.
The G4 Web Control application is sent by the panel to the computer that is used for
communication. Once the application is installed, this popup will no longer appear.
This popup will only appear if you are connecting to the target panel using a different
computer.
7. In some cases, you might get a Connection Details dialog (FIG. 69) requesting a VNC Server
IP Address. This is the IP Address not the IP of the Master but of the target touch panel.
Depending on which method of communication you are using, it can be found in either the:
Wired Ethernet - System Connection > IP Settings section within the IP Address field.
Wireless - Secondary Connection > IP Settings section within the IP Address field.
If you do not get this field continue to step 8.
IP Address of touch panel
- obtained from IP Settings section of
the System Connection page
FIG. 69 Connection Details dialog
8. If a Web Control password was setup on the G4 Web Control page, a G4 Authentication
Session password dialog box (FIG. 68) appears on the screen within the secondary browser
window.
9. Enter the Web Control session password into the Session password field (FIG. 68). This
password was previously entered into the Web Control Password field within the G4 Web
Control page on the panel.
10. Click OK to send the password to the panel and begin the session. A confirmation message
appears stating "Please wait, Initial screen loading..".
The secondary window then becomes populated with the same G4 page being displayed on the
target G4 panel. A small circle appears within the on-screen G4 panel page and corresponds to the
location of the mouse cursor. A left-mouse click on the computer-displayed panel page equates to
an actual touch on the target G4 panel page.
7" Modero Widescreen Touch Panels
75
Configuring Communication
76
7" Modero Widescreen Touch Panels
Upgrading Modero Firmware
Upgrading Modero Firmware
Before beginning the Upgrade process:
Setup and configure your NetLinx Master. Refer to the your particular NetLinx Master
Instruction Manual for detailed setup procedures.
Calibrate and prepare the communication pages on the Modero panel for use. Refer to the
Panel Calibration section on page 45.
Refer to the NetLinx Studio version 2.3 or higher Help file for more information on
uploading files via Ethernet.
Configure your panel for either direct connect or wireless communication. Refer to the
Configuring Communication section on page 47 for more information.
It is recommended that firmware KIT files only be transferred over a direct
Ethernet connection and only when the panel is connected to a power supply.
If battery power or wireless connection fails during a firmware upgrade, the
panel flash file system may become corrupted.
The process of updating firmware involves the use of a communicating NetLinx Master. The
required steps for updating firmware to a Modero panel are virtually identical to those necessary for
updating KIT files to a NetLinx Master (except the target device is a panel instead of a Master).
Refer to either your Master’s literature or Studio 2.3 Help file for those procedures.
A touch panel which is not using a valid username and password will not be able to
communicate with a secured Master. If you are updating the firmware on or through a
panel which is not using a username or password field, you must first remove the
Master Security feature to establish an unsecured connection.
Upgrading the Modero Firmware via the USB port
Before beginning with this section, verify your panel is both powered and the Type-A USB
connector is securely inserted into the PC’s USB port. The panel must be powered-on before
connecting the mini-USB connector to the panel.
Establishing a USB connection between the PC and the panel, prior to installing the
latest NetLinx Studio and TPDesign4 applications will cause a failure in the USB
driver installation.
This driver must first be saved to the PC as part of the new NetLinx Studio and
TPDesign4 application installations.
Step 1: Configure the panel for a USB Connection Type
1. After the installation of the USB driver has been completed; confirm the proper installation of
the large Type-A USB connector to the PC's USB port, and restart your machine.
2. After the CV7 panel powers-up, press and hold the grey Front Setup Access button
(for 3 seconds) to continue with the setup process and proceed to the Setup page.
3. Select Protected Setup > System Connection (located on the lower-left) to open the System
Connection page.
7" Modero Widescreen Touch Panels
77
Upgrading Modero Firmware
4. Toggle the blue Type field (from the Master Connection section) until the choice cycles to
USB.
ALL fields are then greyed-out and read-only, but still display any previous network
information.
5. Press the Back button on the touch panel to return to the Protected Setup page.
6. Press the on-screen Reboot button to both save any changes and restart the panel. Remember
that the panel’s connection type must be set to USB prior to rebooting the panel and prior to
inserting the USB connector.
7. ONLY AFTER the unit displays the first panel page, THEN insert the mini-USB connector
into the Program Port on the panel. It may take a minute for the panel to detect the new
connection and send a signal to the PC (indicated by a green System Connection icon).
If a few minutes have gone by and the System Connection icon still does not turn green,
complete the procedures in the following section to setup the Virtual Master and refresh
the System from the Online Tree. This action sends out a request to the panel to respond
and completes the communication (turning the System Connection icon green).
8. Navigate back to the System Connection page.
Step 2: Prepare NetLinx Studio for communication via the USB port
1. Launch NetLinx Studio 2.3 (default location is Start > Programs > AMX Control Disc >
NetLinx Studio > NetLinx Studio 2.3).
2. Select Settings > Master Communication Settings, from the Main menu to open the Master
Communication Settings dialog (FIG. 70).
IP Address of computer
(not needed as this is a direct
USB connection)
FIG. 70 Assigning Communication Settings for a Virtual Master
3. Click the Communications Settings button to open the Communications Settings dialog.
4. Click on the NetLinx Master radio button (from the Platform Selection section) to indicate
that you are working as a NetLinx Master.
78
7" Modero Widescreen Touch Panels
Upgrading Modero Firmware
5. Click on the Virtual Master radio box (from the Transport Connection Option section) to
indicate you are wanting to configure the PC to communicate directly with a panel. Everything
else such as the Authentication is greyed-out because you are not going through the Master’s
UI.
6. Click the Edit Settings button (on the Communications Settings dialog) to open the Virtual
NetLinx Master Settings dialog (FIG. 70).
7. From within this dialog enter the System number (default is 1).
8. Click OK three times to close the open dialogs, save your settings, and return to the main
NetLinx Studio application.
9. Click the OnLine Tree tab in the Workspace window to view the devices on the Virtual
System. The default System value is one.
10. Right-click on the Empty Device Tree/System entry and select Refresh System to re-populate
the list.
The panel will not appear as a device below the virtual system number (in the Online Tree
tab) until both the system number used in step 7 for the Virtual NetLinx Master (VNM) is
entered into the Master Connection section of the System Connection page and the panel is
restarted.
If the G4 panel does not appear, refer to the Troubleshooting section on page 163 for
more information.
Step 3: Confirm and Upgrade the firmware via the USB port
Use the CC-USB Type-A to Mini-B 5-wire programming cable (FG10-5965) to provide
communication between the mini-USB Program port on the touch panel and the PC. This method
of communication is used to transfer firmware KIT files and TPD4 touch panel files.
A mini-USB connection is only detected after it is installed onto an active
panel. Connection to a previously powered panel which then reboots, allows
the PC to detect the panel and assign an appropriate USB driver.
1. Verify this direct USB connection (Type-A on the panel to mini-USB on the panel) is
configured properly using the steps outlined in the previous two sections.
2. With the panel already configured for USB communication and the Virtual Master setup within
NetLinx Studio, its now time to verify the panel is ready to receive files.
3. After the Communication Verification dialog window verifies active communication between
the Virtual Master and the panel, click the OnLine Tree tab in the Workspace window
(FIG. 71) to view the devices on the Virtual System. The default System value is one.
4. Right-click on the System entry (FIG. 71) and select Refresh System to re-populate the list.
Verify the panel appears in the OnLine Tree tab of the Workspace window.
The default Modero panel value is 10001.
7" Modero Widescreen Touch Panels
79
Upgrading Modero Firmware
Showing the Virtual Master
firmware version and
device number
Shows NetLinx Studio
version number
Showing the current Modero
panel firmware version and
device number
FIG. 71 NetLinx Workspace window (showing the panel connection via a Virtual NetLinx Master)
The panel firmware is shown on the right of the listed panel.
Download the latest firmware file from www.amx.com and then save the KIT file to
your computer.
5. If the panel firmware version is not the latest available; locate the latest firmware file from the
www.amx.com > Tech Center > Downloadable Files > Firmware Files > Modero Panels
section of the website.
6. Download the appropriate KIT file to your computer.
7. Verify you have downloaded the latest Modero firmware (KIT) file to a known location.
8. Select Tools > Firmware Transfers > Send to NetLinx Device from the Main menu to open
the Send to NetLinx Device dialog (B in FIG. 72). Verify the panel’s System and Device
number values match those values listed within the System folder in the OnLine Tree tab of
the Workspace window (A in FIG. 72).
A
B
FIG. 72 Using USB for a Virtual Master transfer
9. Select the panel’s KIT file from the Files section.
10. Enter the Device value associated with the panel and the System number associated with the
Master (listed in the OnLine Tree tab of the Workspace window). The Port field is greyed-out.
80
7" Modero Widescreen Touch Panels
Upgrading Modero Firmware
11. Click the Reboot Device checkbox. This causes the touch panel to reboot after the firmware
update process is complete. The reboot of the panel can take up 30 seconds after the firmware
process has finished.
12. Click Send to begin the transfer. The file transfer progress is indicated on the bottom-right of
the dialog (B in FIG. 72).
13. As the panel is rebooting, temporarily unplug the USB connector on the panel until the panel
has completely restarted.
14. Once the first panel page has been displayed, reconnect the USB connector to the panel.
15. Right-click the associated System number and select Refresh System. This causes a refresh of
all project systems, establishes a new connection to the Master, and populates the System list
with devices on your particular system.
16. Confirm the panel has been properly updated to the correct firmware version.
Upgrading the Modero Firmware via Ethernet (IP Address)
Before beginning with this section, verify that your panel is powered and connected to the NetLinx
Master through an Ethernet connection (direct or wireless).
Step 1: Prepare the Master for communication via an IP
1. Obtain the IP Address of the NetLinx Master from your System Administrator. If you do not
have an IP Address for the Master, refer to your particular Master’s instruction manual for
more information on obtaining this IP Address using NetLinx Studio 2.3 or higher.
From the Online Tree tab of the Workspace window, select the NetLinx Master.
Follow steps outlined in either the Obtaining or Assigning the Master’s IP Address
sections from your particular NetLinx Master instruction manual to use an address.
Note the IP Address and Gateway information.
2. Launch NetLinx Studio 2.3 (default location is Start > Programs > AMX Control Disc >
NetLinx Studio > NetLinx Studio 2.3).
3. Select Settings > Master Communication Settings, from the Main menu to open the Master
Communication Settings dialog (FIG. 73).
4. Click the Communications Settings button to open the Communications Settings dialog.
5. Click on the NetLinx Master radio button (from the Platform Selection section) to indicate
that you are working with a NetLinx Master (such as the NXC-ME260/64 or NI-Series of
Integrated Controllers).
6. Click on the Authentication Required radio box (if the Master is secured) and then enter a
username and password.
7. Click on the TCP/IP radio button (from the Transport Connection Option section) to indicate
you are connecting to the Master through an IP Address.
8. Click the Edit Settings button (on the Communications Settings dialog) to open the TCP/IP
Settings dialog (FIG. 73).
7" Modero Widescreen Touch Panels
81
Upgrading Modero Firmware
List of previously saved IP Addresses
FIG. 73 Assigning Communication Settings and TCP/IP Settings
9. From within the TCP/IP dialog click New to enter the IP information for a new IP Address or
select from the list of previously entered IP Address and alter their properties by clicking the
Edit button and making your changes.
10. Enter the IP Address into the TCP/IP Address field. This information is obtained from either
your System Administrator or obtained from the Master.
11. Click OK when you are done adding or editing the IP Address from the New/Edit TCP/IP
Setting dialog.
12. Click OK three more times to close the open dialogs and save your settings.
13. Click Yes to interrupt the current communication from the Master and apply the new settings.
14. Select Tools > Reboot the Master Controller to access the Reboot the Master dialog, then
click Reboot to reboot the Master and incorporate any changes.
15. Once the dialog replies with "Reboot of system complete", press Done.
16. Click the OnLine Tree tab in the Workspace window to view the devices on the System. The
default System value is one.
17. Right-click on the Empty Device Tree/System entry and select Refresh System to re-populate
the list.
Step 2: Prepare the panel for communication via an IP
1. Press the blue Type field (from the Master Connection section) until the choice cycles to the
word Ethernet.
2. Press the blue Mode field until the choice cycles to the word URL.
By selecting URL, the System Number field becomes read-only (grey) because the panel
pulls this value directly from the communicating target Master (virtual or not). A Virtual
Master system value can be set within the active AMX software applications such as:
NetLinx Studio, TPD4, or IREdit.
3. Press the red Master IP/URL field to open a Keyboard and enter the NetLinx Master’s
IP Address (obtained from the Diagnostics - Networking Address dialog of the NetLinx
Studio application).
82
7" Modero Widescreen Touch Panels
Upgrading Modero Firmware
4. Click Done to accept the new value and return to the System Configuration page.
5. Do not alter the Master Port Number value (this is the default value used by NetLinx).
6. Press the Back button to return to the Protected Setup page and press the on-screen Reboot
button to restart the panel and save any changes.
Step 3: Verify and Upgrade the panel firmware via an IP
1. Click the OnLine Tree tab in the Workspace window to view the devices on the System. The
default System value is one.
2. Right-click the associated System number (from the Workspace window) and select Refresh
System to detect of all devices on the current system, establish a new connection to the Master,
and refresh the System list with devices on that system.
3. After the Communication Verification dialog window verifies active communication between
the PC and the Master, verify the panel appears in the OnLine Tree tab of the Workspace
window (FIG. 74). The default Modero panel value is 10001.
Showing the NetLinx Master
firmware version and
device number
Showing the current Modero
panel firmware version and
device number
Shows NetLinx Studio
version number
FIG. 74 NetLinx Workspace window (showing connected Modero panel)
The panel firmware is shown on the right of the listed panel. New G4 firmware
features are available with firmware beginning with v2.XX.
4. If the panel firmware version is not the latest available; locate the latest firmware file from the
www.amx.com > Tech Center > Downloadable Files > Firmware Files > Modero Panels
section of the website.
5. Download the appropriate KIT file to your computer.
6. Verify you have downloaded the latest Modero firmware (KIT) file to a known location.
7. Select Tools > Firmware Transfers > Send to NetLinx Device from the Main menu to open
the Send to NetLinx Device dialog (FIG. 75). Verify the panel’s System and Device number
values match those values listed within the System folder in the OnLine Tree tab of the
Workspace window.
8. Select the panel’s KIT file from the Files section (FIG. 75).
9. Enter the Device value associated with the panel and the System number associated with the
Master (listed in the OnLine Tree tab of the Workspace window). The Port field is greyed-out.
7" Modero Widescreen Touch Panels
83
Upgrading Modero Firmware
Selected Firmware file
Description field for selected KIT file
Firmware download
status
Device and System values
listed in the Workspace window
must match the System and Device values
FIG. 75 Send to NetLinx Device dialog (showing Modero firmware update via IP)
10. Click the Reboot Device checkbox. This causes the touch panel to reboot after the firmware
update process is complete. The reboot of the panel can take up 30 seconds after the firmware
process has finished.
11. Click Send to begin the transfer. The file transfer progress is indicated on the bottom-right of
the dialog (FIG. 75).
12. Click Close (after the panel reboots) to return to the main program.
13. Right-click the associated System number and select Refresh System. This causes a refresh of
all project systems, establishes a new connection to the Master, and populates the System list
with devices on your particular system.
14. Confirm the panel has been properly updated to the correct firmware version.
84
7" Modero Widescreen Touch Panels
Firmware Pages and Descriptions
Firmware Pages and Descriptions
This section describes each firmware page and their specific functional elements.
Setup Navigation Buttons
These Setup Navigation Buttons (FIG. 76) appear on the left of the panel screen when the Setup
page is currently active.
Modero Setup
Navigation Buttons
FIG. 76 Setup Navigation Buttons
These Navigation Buttons are specific to these Modero panels and include the specific elements
described in the following table:
Setup Navigation Button Elements
Project Information:
Press the Project Information button to access the Project Information and view
the TPD4 project file properties currently loaded on the selected panel
(read-only).
• Refer to the Project Information Page section on page 88 for more detailed
information.
Panel Information:
Press the Panel Information button to access the Panel Information page and
view panel specific information such as resolution, memory, etc. (read-only).
• Refer to the Panel Information Page section on page 89 for more detailed
information.
Time Adjustment:
Press the Time Adjustment button to access the Time Adjustment page where
you can alter the time and date settings on the Master.
• Refer to the Time & Date Setup Page section on page 90 for more detailed
information.
Audio Adjustments:
Press the Audio Adjustments button to access the Volume page where you can
alter the audio parameters on the Modero panel.
• Refer to the Volume Page section on page 92 for more detailed information.
7" Modero Widescreen Touch Panels
85
Firmware Pages and Descriptions
Setup Navigation Button Elements (Cont.)
Protected Setup:
Press the Protected Setup button to access the Protected Setup page section
that provides access to the panel’s sensors, calibration features, and
connection settings.
• Refer to both the Protected Setup Navigation Buttons section on page 97 and
Protected Setup Page section on page 98 for more detailed information.
Video Adjustment:
Press the Video Adjustment button to access the Video Adjustment page where
you can set the video properties for incoming video.
• This button only appears on Color Video (CV) capable touch panels.
• Refer to the Video Adjustment Page section on page 93 for more detailed
information.
Battery Base:
Press the Battery Base button to access the Battery Base page where you can
modify and monitor NXT-BP Modero Power Pack parameters.
• This button only appears when a Modero Table Top panel (NXT) is connected
to an NXA-BASE/B battery base.
• Refer to the Battery Base Page section on page 95 for more detailed
information.
Setup Page
This page (FIG. 77) centers around basic Modero panel properties such as: Connection Status of
the panel, Display Timeout, Inactivity Page Flip Time, Inactivity page file, and the Panel
Brightness.
Connection Status
Red Connection Status icon indicates no connection
to a Master
Green Connection Status icon indicates communication
to a Master
Battery Base button doesn’t appear
until NXT is connected to a BASE/1
FIG. 77 Setup page
The elements of the Setup page are described in the table below:
Setup Page Elements
Exit:
Returns you to the Main touch panel page. In this case, the previous page is the
default Main page.
Connection Status icon:
This visual display of the connection status allows the user to have a current
update of the panel’s connection status regardless of what page is
currently active.
• A Lock only appears on the icon if the panel has established a connection
with a currently secured target Master (requiring a username and password).
86
7" Modero Widescreen Touch Panels
Firmware Pages and Descriptions
Setup Page Elements (Cont.)
Connection Status:
Displays whether the panel is communicating externally, the encryption status
of the communicating Master, what connection type is being used (Ethernet or
USB), and what System the panel is a part of.
This visual display of the connection status is also reflected at the upper-right of
each firmware page. This allows the user to have a current visual update of the
panel’s connection status regardless of what page is currently active.
• When a connection is established, the message displayed is either:
"Connected via Ethernet " or "Connected via USB ".
• If no connection can be established by the Modero panel, it will continue to try
and establish a connection while displaying: "Attempting via ...".
• The word "Encrypted" appears only when an encrypted connection is
established with a target Master.
• The panel must be rebooted before incorporating any panel communication
changes and detecting any active Ethernet connections.
The Ethernet connection is not detected until after a reboot.
Display/Panel Timeout:
Sets the length of time the panel can remain idle before activating the sleep
mode. When the device goes into sleep mode, the LCD is powered-down.
• Press the UP/DN buttons to increase/decrease the time until the panel
times out. Range = 0 - 240 minutes.
• Use this button to set the timeout value to zero and disable the sleep mode.
• Note: Display timeout values affect battery performance. Small timeout
values increase the life of the battery charge. Greater timeout values
may require more frequent battery charging.
Inactivity Page Flip
Timeout:
Sets the number of minutes of inactivity before the panel automatically flips to a
pre-selected touch panel page. When the device goes into this inactivity mode,
the LCD does not power-down.
• Press the UP/DN buttons to increase/decrease the time the panel can remain
inactive before it flips to the preset page. Range = 0 - 240 minutes.
• Use this button to set the timeout value to zero and disable the inactivity page
flip mode.
• The touch panel page used for the Inactivity page flip is shown within a small
Inactivity Page field.
Panel Brightness:
Sets the display brightness level of the panel.
• Press the UP/DN buttons to adjust the brightness level. Range = 0 - 100.
• The on-screen bargraph can be dragged to adjust the Brightness level which
is then reflected as a corresponding numeric value within the Panel
Brightness field.
7" Modero Widescreen Touch Panels
87
Firmware Pages and Descriptions
Project Information Page
The Project Information page displays the TPDesign4 (TPD4) project file properties currently
loaded on the selected Modero panel (FIG. 78). Refer to the TPDesign4 Touch Panel Program
instruction manual for more specific information on uploading TPDesign4 files to a panel.
FIG. 78 Project Information page (showing the TPD4 project properties tabs)
The elements of the Project Information page are described in the table below:
Project Information Page Elements
Back:
Returns you to the previously active touch panel page.
Connection Status icon:
This visual display of the connection status allows the user to have a current
visual update of the panel’s connection status regardless of what page is
currently active.
• A Lock only appears on the icon if the panel has established a connection
with a currently secured target Master (requiring a username and password).
File Name:
Displays the name of the TPDesign4 project file downloaded to the panel.
Designer ID:
Displays the designer information.
File Revision:
Displays the revision number of the file.
Dealer ID:
Displays the dealer ID number (unique to every dealer and entered in TPD4).
Job Name:
Displays the job name.
Sales Order:
Displays the sales order information.
Purchase Order:
Displays the purchase order information.
AMX IR 38k Assigned Port: Displays the AMX 38 kHz IR channel port used by the IR receiver on the panel.
• This information is pulled by the panel from AMX IR Receivers section of the
TPD4 Project Properties > IR Emitters & Receivers tab.
• For IR reception, this is the port that reports a push on for the corresponding
IR code.
• IR receivers and transmitters on G4 panels share the device address number
of the panel.
88
7" Modero Widescreen Touch Panels
Firmware Pages and Descriptions
Project Information Page Elements (Cont.)
AMX IR 455k
Assigned Port:
Displays the AMX 455 kHz IR channel port used by the IR receiver on the
panel.
This information is pulled by the panel from AMX IR Receivers section of the
TPD4 Project Properties > IR Emitters & Receivers tab.
• For IR reception, this is the port that reports a push on for the corresponding
IR code.
• IR receivers and transmitters on G4 panels share the device address number
of the panel.
Build Number:
Displays the build number information of the TPD4 software used to create the
project file.
Creation Date:
Displays the project creation date.
Revision Date:
Displays the last revision date for the project.
Last Save Date:
Displays the last date the project was saved.
Blink Rate:
Displays the feedback blink rate (10th of second).
Job Comments:
Displays any comments associated to the job. These comments are taken from
the TPD4 project file.
Panel Information Page
The Panel Information page (FIG. 79) centers around Modero panel properties such as: resolution
used, on-board memory, firmware, address/channel information, and string information.
This information is retrieved
from the Modero panel
FIG. 79 Panel Information page (takes its’ information from the touch panel)
The elements of the Panel Information page are described in the table below:
Panel Information Page Elements
Back:
Returns you to the previously active touch panel page.
Connection Status icon:
This visual display of the connection status allows the user to have a current
visual update of the panel’s connection status regardless of what page is
currently active.
• A Lock only appears on the icon if the panel has established a connection
with a currently secured target Master (requiring a username and password).
Panel Type:
Displays the model of the Modero panel being used.
Firmware Version:
Displays the G4 firmware version being used by the panel.
• Verify you have the latest version from www.amx.com.
7" Modero Widescreen Touch Panels
89
Firmware Pages and Descriptions
Panel Information Page Elements (Cont.)
Setup Port:
Displays the setup port information/value being used by the panel.
High Port:
Displays the high port (port count) value for the panel.
High Address:
Displays the high address (address count) value for the panel.
High Channel:
Displays the high channel (channel count) value for the panel.
High Level:
Displays the high level (level count) value being used by the panel.
Serial Number:
Displays the specific serial number value assigned to the panel.
Setup Pages Version:
Displays the type and version of the Setup pages being used by the panel.
Screen Width:
Displays the pixel width being used to display the incoming video signal on the
Modero panel.
• Maximum available screen width on a CV7 Modero panel is 800 pixels.
Screen Height:
Displays the pixel height being used to display the incoming video signal on the
Modero panel.
• Maximum available screen height on a CV7 Modero panel is 480 pixels.
Screen Refresh Rate:
Displays the video refresh rate applied to the incoming video signal from the
panel. Default rate is 60.
Screen Rotation:
Displays the degree of rotation applied to the on-screen image.
Power Up Pages:
Displays the first touch panel page assigned for display after the device is
powered-up.
• This information is taken from the TPD4 project file.
• Most projects begin with a Main page.
Start Up String:
Displays the start-up string.
Wake Up String:
Displays the wake up string used after an activation from a timeout.
Sleep String:
Displays the sleep string used during a panel’s sleep mode.
File System:
Displays the amount of Compact Flash memory available on the Modero panel.
RAM:
Displays the available RAM (or Extended Memory module) on the Modero
panel.
Time & Date Setup Page
The Time & Date Setup page (FIG. 80) allows you to alter/set the time and date information on
the NetLinx Master. If either the Time/Date is modified on this page (then updated to the Master by
pressing the Set Time button), all devices communicating to that target Master will then be updated
to reflect the new information.
Time Display
fields
Date Display
fields
Currently
selected
FIG. 80 Time and Date Setup page
90
7" Modero Widescreen Touch Panels
Firmware Pages and Descriptions
The only way to modify a panel’s time, without altering the Master, is to use NetLinx
Code.
The elements of the Time & Date Setup page are described in the table below:
Time & Date Setup Page Elements
Back:
Returns you to the previously active touch panel page without saving changes
(to save changes, use the Set Time button).
Connection Status icon:
This visual display of the connection status allows the user to have a current
visual update of the panel’s connection status regardless of what page is
currently active.
• A Lock only appears on the icon if the panel has established a connection
with a currently secured target Master (requiring a username and password).
Time Date Refresh/Set:
This section provides you with two options:
• The Get Time/Date button retrieves the Time and Date information from the
Master.
• The Set Time/Date button sets the Master to retain and save any
time/date modifications made on the Time and Date Setup page.
Time Display fields:
• These fields display the time in three formats: STANDARD, STANDARD
AM/PM, and 24 HOUR.
Date Display fields:
• These fields display the calendar date information in several different formats.
Set Date/Time:
This section provides a user with both UP/DN arrow buttons to alter the
Master’s calendar date and time. The blue circle indicates which field is currently selected.
• Select the Year field and use the UP/DN buttons to alter the year value
(range = 2000 - 2037).
• Select the Month field and use the UP/DN buttons to alter the month value
(range = 1 - 12).
• Select the Day field and use the UP/DN buttons to alter the day value
(range = 1 - 31).
• Select the Hour field and use the UP/DN buttons to alter the hour value
(24-hour military).
• Select the Minute field and use the UP/DN buttons to alter the minute value
(range = 0 - 59).
• Select the Second field and use the UP/DN buttons to alter the second value
(range = 0 - 59).
CV7 touch panels do not have an on-board clock. This page both receives and sets
the time/date of the NetLinx Master.
7" Modero Widescreen Touch Panels
91
Firmware Pages and Descriptions
Volume Page
The Volume page (FIG. 81) (accessed by pressing the Audio Adjustments button on the Setup page)
allows you to adjust the master volume parameters and default panel sounds on the panel.
FIG. 81 Volume configuration page
The elements of the Volume page are described in the table below:
Volume Page Elements
Back:
Saves the changes and returns you to the previously active touch panel page.
Connection Status icon:
This visual display of the connection status allows the user to have a current
visual update of the panel’s connection status regardless of what page is
currently active.
• A Lock only appears on the icon if the panel has established a connection
with a currently secured target Master (requiring a username and password).
Master Volume:
This section allows you to alter the current master volume level:
• Use the UP/DN buttons to adjust the volume level (range = 0 - 100).
• The Master Volume bargraph indicates the current volume level.
• The Mute button toggles the Mute feature.
• The Play Test button plays a test WAV/MP3 file over the panel’s internal
speakers.
Mic Out Level:
Allows you to adjust the current Microphone volume level (being received from
the communicating breakout box).
• Use the UP/DN buttons to adjust the Microphone volume level
(range = 0 - 100).
• The Mic Out Level bargraph indicates the current Mic Out level.
Internal Sound Level:
This section allows you to adjust the current sound level on the internal panel
speaker:
• Use the UP/DN buttons to adjust the volume output on the internal speakers
(range = 0 - 100).
• The Internal Sound Level bargraph indicates the current sound level.
• The Mute button mutes the volume.
Line In Level:
Allows you to adjust the current Line-In volume level (being received from the
communicating breakout box).
• Use the UP/DN buttons to adjust the Line-In volume level (range = 0 - 100).
• The Line-In Level bargraph indicates the current Line-In level.
• The Mute button mutes the Line-In volume.
92
7" Modero Widescreen Touch Panels
Firmware Pages and Descriptions
Volume Page Elements (Cont.)
Default Panel Sounds:
Sets the Modero panel to play either the default Button Hit sound (when you
touch an active button) and/or the default Button Miss sound (when you touch
a non-active button or any area outside of the active button).
Supported sampling rates for WAV
The following is a listing of supported sampling rates associated for WAV files played on CV7
panels. Some WAV files currently played on Modero's may not work on these panels. The
supported sampling rates for WAV files are:
Supported WAV Sampling Rates
• 48000 Hz
• 16000 Hz
• 44100 Hz
• 12000 Hz
• 32000 Hz
• 11025 Hz
• 24000 Hz
• 8000 Hz
• 22050 Hz
Protected Setup Page
This button opens the Protected Setup page which centers around the properties used by the panel
to properly communicate with the NetLinx Master. Refer to both the Protected Setup Navigation
Buttons section on page 97 and the Protected Setup Page section on page 93 for more detailed
information.
Video Adjustment Page
The Video Setup page (FIG. 82) (accessed by pressing the Video Adjustment button on the Setup
page) sets the Video properties of the incoming video signal from an NXA-AVB/ETHERNET
Breakout Box.
Incoming Video signal
Once done making your screen
adjustments, SAVE SETTINGS.
FIG. 82 Video Setup page (showing default values)
7" Modero Widescreen Touch Panels
93
Firmware Pages and Descriptions
The elements of the Video Setup page are described in the table below:
Video Setup Page Elements
Back:
Saves the changes and returns you to the previously active touch panel page.
Connection Status icon:
This visual display of the connection status allows the user to have a current
visual update of the panel’s connection status regardless of what page is
currently active.
• A Lock only appears on the icon if the panel has established a connection
with a currently secured target Master (requiring a username and password).
Settings:
• The Default Settings button sets the video settings to their default values
(indicated in this table).
• The Undo Changes button disregards any changes made on the page since
the last settings were saved.
• The Save Settings button saves any changes made to this page.
Video Settings:
• The Black & White button toggles the Black & White display mode.
Default = Off.
• The Sharpness button toggles the Interpolate (Sharpness) feature.
Default = Off.
• The Interlace button toggles the Interlacing feature.
Default = On.
Status:
Displays whether or not a video-sync signal is detected.
Format:
Allows you to press this blue field and cycle through a choice of available video
formats (NTSC, PAL, SECAM, or Auto detect).
• Default = Auto.
Brightness:
Use the UP/DN buttons to alter the brightness level of the incoming signal.
• Range = 0 - 255, default = 128.
Contrast:
Use the UP/DN buttons to alter the contrast level of the incoming signal.
• Range = 0 - 255, default = 128.
Saturation:
Use the UP/DN buttons to alter the color saturation level of the incoming signal.
• Range = 0 - 255, default = 128.
Hue:
Use the UP/DN buttons to alter the hue level of the incoming signal.
• Range = 0 - 255, default = 128.
94
7" Modero Widescreen Touch Panels
Firmware Pages and Descriptions
Battery Base Page
This page (FIG. 83) allows you to alter/set the power warning preferences, monitor battery status
information, and alter the display times for the battery warnings. The fields on this page are
populated with information after the panel is connected to an optional NXA-BASE/1 Battery Base
containing a single NXT-BP battery.
FIG. 83 Battery Base page
This page is ONLY available on CV7 Table Top panels (NXT) using an NXA-BASE/1. The
elements of the Battery Base page are described in the table below:
Battery Base Page Elements
Back:
Saves the changes and returns you to the previously active touch panel page.
Connection Status icon:
This visual display of the connection status allows the user to have a current
visual update of the panel’s connection status regardless of what page is
currently active.
• A Lock only appears on the icon if the panel has established a connection
with a currently secured target Master (requiring a username and password).
Charge Status:
Time Remaining (blue) indicates the amount of charge time (use) remaining
on the battery within the connected NXA-BASE/1.
Time Until Charged (green) indicates the amount of time remaining until the
battery installed within the connected NXA-BASE/1 is fully charged.
• Range = 0:00 - 12:59. This is read in HH:MM, hours and minutes.
Panel Shutdown:
The Panel Shutdown UP/DN buttons alter the timeout value (in minutes).
• This value determines the number of minutes that would need to pass before
the panel automatically shuts-down.
• Once shutdown, the unit would have to be restarted. A zero value disables
this feature. Range = 0 - 240, default = 0 min.
Low Battery Warning:
The Low Battery Warning UP/DN buttons alter the time value (in minutes)
available on the battery (for use) before the panel displays a low battery
warning.
• Range - 10 - 45, default = 15 min.
7" Modero Widescreen Touch Panels
95
Firmware Pages and Descriptions
Battery Base Page Elements (Cont.)
Very Low Battery Warning: The Very Low Battery Warning UP/DN buttons alter the time value
(in minutes) available on the battery (for use) before the panel displays a very
low battery warning. This indicates a near-term panel shutdown.
• Range = 3 - 15, default = 5 min.
- This value can never exceed the Low Battery Warning value.
• When the NXT-BP battery (installed within the NXA-BASE/1 battery base)
reaches a point where it needs to be recalibrated.
- A recalibration pop-up screen appears to ask whether or not you choose
to recalibrate the battery at this time.
Battery Status fields:
This section provides the ability to monitor the current battery charge level and
charge quality:
• The Battery One Charge Status bargraph indicates the power charge
available on the Slot 1 internal battery connection (bargraph range = 0 - 100).
• The Battery One Quality bargraph indicates the physical capacity (quality) of
the battery. Quality is the percentage of actual capacity vs. its rated capacity.
For optimal performance, a battery should be replaced when the quality
rating drops below 80%.
• The Base Version field indicates the firmware version being used by the
NXA-BASE/1 Battery Base connected to the NXT CV7 panel.
• The Battery Level Port field indicates the port being used to report the
charge status level back to the NetLinx Master on (set in TPD4).
• The Battery Level field indicates the level being used to report the charge
status level back to the NetLinx Master on (set in TPD4).
Battery Power Brightness
Limit:
The DISABLE/DISABLED button acts as a power save feature with two
available choices:
• Disable - activates the brightness limit set on the Modero panel and is used
to conserve battery power. Activating this feature causes the panel to
function at 80% of full brightness and overrides the Panel Brightness value
set on the Setup page. This extends the battery usage time.
• Disabled - (illuminated when selected) deactivates this power save feature
and makes the panel use the specified Panel Brightness level set on the
Setup page.
The term "quality" (in the context of a battery), refers to the current capacity relative to
the batteries’ rated capacity. For example, after constant use, a battery may be
operating at 75% of its rated capacity even though it might be fully charged. In this
case, the battery could be incorrectly reporting its’ information back to the battery
base and then consequently relating this information back to the Battery Base page.
A battery can be recalibrated using an optional NXT-CHG (battery charger).
96
7" Modero Widescreen Touch Panels
Firmware Pages and Descriptions
Protected Setup Navigation Buttons
The Protected Setup Navigation Buttons (FIG. 84) appear on the left of the panel screen when the
Protected Setup page is currently active.
Modero Protected
Setup Navigation
Buttons
FIG. 84 Protected Setup Navigation Buttons
These Navigation Buttons are specific to these Modero panels and include panel specific elements
described in the following table:
Protected Setup Navigation Button Elements
G4 Web Control:
Press the G4 Web Control button to access the G4 Web Control page where
you can enable or disable display and control of your panel (via the web) by a
PC running a VNC client.
• Refer to the G4 Web Control Page section on page 100 for more detailed
information.
Sensors:
Press the Sensors button to access the Sensors Setup page where you can
modify/monitor both the light and motion sensor settings.
• Refer to the Sensor Setup section on page 101 for more detailed information.
Passwords:
Press the Passwords button to access the Passwords Setup page where you
can specify up to five security passwords. Default password is 1988.
• Refer to the Password Setup Page section on page 104 for more detailed
information.
Calibrate:
Press the Calibrate button to access the Calibration page where you can use
the displayed set of crosshairs to calibrate a touch panel.
• Refer to the Calibration Page section on page 105 for more detailed
information.
Secondary Connection:
Press the Secondary Connection button to access the Secondary Connection
page where you can setup the wireless connection parameters used by the
NXA-WC80211B/CF wireless interface card located within the Modero panel.
• Refer to the Secondary Connection Page section on page 105 for more
detailed information.
System Connection:
Press the System Connection button to access the System Connection page
where you can alter the communication parameters of both the NetLinx
Master and Modero panel.
• Refer to the System Connection Page section on page 109 for more detailed
information.
7" Modero Widescreen Touch Panels
97
Firmware Pages and Descriptions
Protected Setup Page
The Protected Setup page (FIG. 85) centers around the properties used by the panel to properly
communicate with the NetLinx Master. Enter the factory default password (1988) into the password
keypad to access this page.
Provides access to the panel
firmware pages by enabling the
grey front setup access button:
- Setup page (after a 3 second
press/hold)
- Calibration page (after a 6 second
press/hold)
FIG. 85 Protected Setup page-showing default values
The elements of the Protected Setup page are described in the table below:
Protected Setup Page Elements
Back:
Saves the changes and returns you to the previously active touch panel page.
Connection Status icon:
This visual display of the connection status allows the user to have a current
visual update of the panel’s connection status regardless of what page is
currently active.
• A Lock only appears on the icon if the panel has established a connection
with a currently secured target Master (requiring a username and password).
Device Number:
Opens a keypad that is used to set and display the current device number.
Options:
Allows you to select various touch panel features:
• The Function Show button enables the display of the channel port and
channel code in the top left corner of the button, the level port and level code
in the bottom left corner, and the address port and address code in the
bottom right corner (see FIG. 87 for an example of the function locations).
• Use the Page Tracking button to toggle page tracking. When enabled, the
touch panel sends page data back to the NetLinx Master, or vice versa
depending on the touch panel settings.
• Use the Telnet button to enable or disable the telnet server on the panel. This
feature focuses on direct telnet communication to the panel.
• Use the Front Button Setup Access button to activate the grey Front Setup
Access button (located below the LCD) to access the firmware pages.
- Default condition is On.
- Press and hold this grey button for 3 seconds to access the Setup page.
- Press and hold this grey button for 6 seconds to access the Calibration
page.
Reboot Panel:
98
Pressing this button causes the panel to restart after saving any changes.
7" Modero Widescreen Touch Panels
Firmware Pages and Descriptions
Protected Setup Page Elements (Cont.)
System Recovery:
Allows you to either reset the touch panel to factory default settings and/or wipe
out all existing touch panel pages:
• The Reset System Settings button allows a user to wipe out all current
configuration parameters on the touch panel (such as IP Addresses, Device
Number assignments, Passwords, and other presets).
- Pressing this button launches a Confirmation dialog (FIG. 86) which asks
you to confirm your selection.
- This dialog is configured with a delay timer that does not enable the YES
button for 5 seconds. This delay provides an additional amount of time for
the user to confirm their decision.
• The Remove User Pages button allows you remove all current TPD4 touch
panel pages currently on the panel (including the pre-installed AMX Demo
pages).
- Pressing this button launches a Confirmation dialog (FIG. 86) which asks
you to confirm your selection.
- This dialog is configured with a delay timer that does not enable the YES
button for 5 seconds. This delay provides an additional amount of time for
the user to confirm their decision.
You have a wait time of 5 seconds
before the YES option is enabled.
FIG. 86 Protected Setup page-System Recovery confirmation dialog
Channel Code
Number
Channel Port
Channel Code
Number
Channel Port
3,132
Button
Level Port
2,8
Channel Code
Number
Address
Port
7,10
Slider
Level Port
4,9
3,50
Address Code
Number
Channel Code
Number
Address
Port
1,8
Address Code
Number
FIG. 87 Button/slider Function Show example
7" Modero Widescreen Touch Panels
99
Firmware Pages and Descriptions
G4 Web Control Page
The G4 Web Control page (FIG. 88) centers around enabling and disabling both the display and
control of your panel (via the web). An external PC running a VNC client (installed during the
initial communication to the G4 panel) makes this possible.
FIG. 88 G4 Web Control page
Each panel supports the open standard Virtual Network Computing (VNC) interface. These panels
contain a VNC server that allows them to accept a connection from any other device running a
VNC client. Once a connection is established to that target device, the client can control the touch
panel remotely. The elements of the G4 Web Control page are described in the table below:
G4 Web Control Page Elements
Back:
Saves the changes and returns you to the previously active touch panel page.
Connection Status icon:
This visual display of the connection status allows the user to have a current
visual update of the panel’s connection status regardless of what page is
currently active.
• A Lock only appears on the icon if the panel has established a connection
with a currently secured target Master (requiring a username and password).
G4 Web Control Settings:
Enable/Enabled
Network Interface Select
Sets the IP communication values for the touch panel and contains:
• The Enable/Enabled button allows you to toggle between the two G4
activation settings:
- Enable - deactivates the G4 Web Control feature on the panel.
- Enabled - activates the G4 Web Control feature on the panel and allows
an external PC running a VNC client to access the panel (after the
remaining fields are configured).
Displays the detected method of communication to the web:
• Wired is used when a direct Ethernet connection is being used for
communication to the web. This is a default setting if no wireless interface
card is detected by the panel.
• Wireless is used when a wireless card is detected within the internal card
slot. This method provides an indirect communication to the web via a
pre-configured Wireless Access Point.
Web Control Name
Allows you to enter a unique alpha-numeric string that is used as the display
name of the panel within the Manage WebControls window of the new NetLinx
Security browser window.
• This Web Control tab displays a G4 icon alongside the link to the Web Control
Name given to this panel (FIG. 89).
Web Control Password
100
Allows you to enter the G4 Authentication session password associated for
VNC web access of this panel.
7" Modero Widescreen Touch Panels
Firmware Pages and Descriptions
G4 Web Control Page Elements (Cont.)
G4 Web Control Settings
(Cont.):
Web Control Port
Allows you to enter the port value that the VNC Web Server runs on.
• Default value is 5900.
Maximum Number of
Connections
This read-only field displays the maximum number of users that can be
simultaneously connected to the target panel via the web.
• Default value is 1.
Current Connection Count
G4 Web Control Timeout:
This read-only field displays the current number of users connected to the
target panel via the web. This value cannot exceed the Maximum number field.
Sets the length of time (in minutes) the panel can remain idle (no cursor
movements) before the session is closed and the user is disconnected.
• Minimum value = 0 minutes (panel never times-out)
• Maximum value = 240 minutes (panel times-out after 240 minutes/4hours)
FIG. 89 Sample relationship between G4 Web Control and NetLinx Security-Mange WebControls window
Refer to the Using G4 Web Control to Interact with a G4 Panel section on page 71 for more
detailed instructions on how to use the G4 Web Control page with the new web-based NetLinx
Security application.
Sensor Setup
The Sensor Setup page (FIG. 90) allows you to adjust the Light and Motion Sensor parameters on a
Modero touch panel.
FIG. 90 Sensor Setup page
7" Modero Widescreen Touch Panels
101
Firmware Pages and Descriptions
A light level value between the Minimum and Maximum DIM Mode values delivers an
average light level. The DIM mode Min Level can never exceed the DIM Mode Max
Level.
The elements of the Sensor Setup page are described in the table below:
Sensor Setup Page Elements
Back:
Saves the changes and returns you to the previously active touch panel page.
Connection Status icon:
This visual display of the connection status allows the user to have a current
visual update of the panel’s connection status regardless of what page is
currently active.
• A Lock only appears on the icon if the panel has established a connection
with a currently secured target Master (requiring a username and password).
Light Sensor:
Allows you to monitor and alter the sensitivity of the Modero panel light sensor:
• The Light Sensor Level field indicates the level used to report the light
sensor level back to the NetLinx Master (set in TPD4) (read-only).
• The Light Sensor Level Port field indicates the port used to report the light
sensor level back to the NetLinx Master (set in TPD4) (read-only).
• The Light Sensor Channel field indicates the level used to report the sensor
channel back to the NetLinx Master (set in TPD4). It is On when you are
below the Maximum dim mode level (read-only).
• The Light Sensor Channel Port field indicates the port used to report the
sensor channel back to the NetLinx Master (set in TPD4) (read-only).
• The Light Level field provides a numeric value representing the current value
of the light level detected by the on-board photo-sensor.
• The Light Level bargraph displays a horizontal bargraph indicating the current
value of the light level detected by the on-board photo-sensor. This bargraph
provides a visual representation of the numeric value displayed within the
Light Level field.
• Use the Dim Mode Max Level bargraph to alter the Maximum DIM level value
used to activate the DIM Mode Brightness Level (range = 0 - 100).
• Use the Dim Mode Min Level bargraph to alter the Minimum DIM level value
used to activate the DIM Mode Brightness Level (range = 0 - 100).
- The position of this bargraph can never exceed that of the Dim Mode
Max Level.
Dim Mode Minimum
Brightness:
Allows you to alter the sensitivity of the Modero panel light sensor:
• Toggle the Enable/Enabled button to either active/inactive the DIM Mode
feature:
- Enable - activates this feature. Once active (by receiving a value below the
Dim Mode Min Level value), the current light level ramps to the DIM Mode
value within a few seconds.
- Enabled - (illuminated when selected) deactivates this feature.
• Use the DIM Mode Brightness UP/DN buttons to alter the DIM level.
- Range = 0 - 100.
- The lower the value, the darker a room must be before the LCD Brightness
value changes to conform to a DIM room (and vice versa with a
higher value).
• The DIM Mode Minimum Brightness bargraph indicates the current DIM
Mode Brightness level.
- This level corresponds to the brightness level of the LCD used when
the DIM Mode is active.
- The Brightness value of the panel in a DIM room (low-light) is much
less than that of a Non-DIM (well to brightly-lit) where the LCD Brightness
must be higher to display the screen content clearly.
102
7" Modero Widescreen Touch Panels
Firmware Pages and Descriptions
Sensor Setup Page Elements (Cont.)
Motion Sensor:
Provides the following fields:
• The Motion Detection field displays a reactive button that changes color
(illuminates) and displays the words "Motion Detected" when motion is
detected by the Modero panel’s front motion sensor.
• The Motion Sensor Port field indicates the port used to report the motion
sensor channel back to the NetLinx Master (set in TPD4) (read-only).
• The Motion Sensor Channel field indicates the channel used to report the
motion sensor channel back to the NetLinx Master (set in TPD4) (read-only).
Wake Panel On Motion
Sense:
The Wake Panel Sensitivity relates to the sensitivity of the motion sensor to
detect motion and wake the panel accordingly.
• Toggle the Enable/Enabled button to either active/inactive this feature:
- Enable - activates this feature. Activating this feature reactivates the
panel from a panel timeout (sleep) mode.
- Enabled - (illuminated when selected) deactivates this feature and
makes the panel use the specified Display Timeout value set on the
Setup Page.
• Use the Wake Panel UP/DN buttons to alter the sensitivity value.
- Range = 0 - 100.
• The horizontal WAKE PANEL SENSITIVITY bargraph indicates the current
motion sensitivity value associated with waking the panel from a timeout.
There is a relationship between the motion sensor and the panel sleep feature. If a
panel is set to Sleep Mode, there is a time delay before the motion sensor is activated
to detect motion. By creating a time delay to the detection, this allows a user to set
the sleep mode and leave the panels’ detection range. In this way, the panel doesn’t
awake immediately after the sleep is active and you move away.
Making the most of the Automated Brightness Control feature (DIM Mode)
Please follow the steps below to set up Automated Brightness Control:
1. Set the lighting conditions in the room to maximum (turn On all the lights).
2. Set the Maximum Panel Brightness, from the Setup page, to a comfortable level.
Sitting in front of the panel, you should be able to comfortably see someone sitting
behind the panel without being “blinded” by the panel.
3. Open the Sensors Setup page (FIG. 90) from the Protected Setup menu section.
4. Move around the panel and block the direct or indirect light from the room fixtures with your
body. Take note of the drop in the lighting level being detected by the panel in response to your
movements.
5. Set the Maximum brightness of the Dimmer (Dim Mode Max Level) below the detected drop.
This will make sure that the panel does not react to variations in the lighting conditions of a
normal working environment.
The maximum (upper level) of the dimmer should be at least 15% lower than the
maximum detected level.
6. Set the minimum lighting conditions in the room (not complete darkness but the minimal
lighting setup, unless complete darkness is an “operational option” for the room).
7" Modero Widescreen Touch Panels
103
Firmware Pages and Descriptions
7. Set the Minimum Dimmer Brightness (Dim Mode Min Level) to a comfortable level by sitting
in front of the panel. You should be able to comfortably see someone sitting behind the panel
without being “blinded” by the panel.
8. Move around the panel and block the direct or indirect light from the room fixtures with your
body. Take note of the drop in the lighting level being detected by the panel in response to your
movements.
9. Set the Minimum brightness of the Dimmer (Dim Mode Max Level) below the detected drop.
This will make sure that the panel does not react to variations in the lighting conditions of a
normal working environment.
The minimum (lower level) of the dimmer should be at least 10% lower than the
minimum detected level (ex: lower dimmer level at 30% if the detected lighting of the
room is at 40%).
Password Setup Page
The Password Setup page (FIG. 91) centers around the properties used to assign passwords for the
Modero panel pages.
FIG. 91 Password Setup page
The elements of the Password Setup page are described in the table below:
Password Setup Page Elements
Back:
Saves the changes and returns you to the previously active touch panel page.
Connection Status icon:
This visual display of the connection status allows the user to have a current
visual update of the panel’s connection status regardless of what page is
currently active.
• A Lock only appears on the icon if the panel has established a connection
with a currently secured target Master (requiring a username and password).
In Panel Password
Change:
Accesses the alphanumeric values associated to particular password sets.
• PASSWORD 1, 2, 3, 4, 5 (protected) buttons open a keyboard where you can
enter alphanumeric values associated to a selected password group.
• Clearing Password #5 removes the need to enter a password before
accessing the Protected Setup page.
104
7" Modero Widescreen Touch Panels
Firmware Pages and Descriptions
Calibration Page
This page (FIG. 92) allows you to calibrate the touch panel using the pre-selected touch driver.
Press and hold the grey Front Setup Access button (below the Modero LCD) for
6 seconds to access the Calibration page.
Press the crosshairs to calibrate the panel and return to the last active firmware
page.
The request to touch the crosshairs
is the first on-screen message
Calibration successful is the second
on-screen message that appears
after the calibration process is
completed
On-screen crosshairs used for
calibration of the touch device
FIG. 92 Calibration page (actually 3 separate screens)
If the calibration was improperly set and you cannot return to the Calibration
page (through the panel’s firmware); you can access this firmware page via
G4 WebControl where you can navigate to the Protected Setup page and press the
Calibrate button through your VNC window.
This action causes the panel to go to the Calibration page seen above, where you
can physically recalibrate the actual touch panel again using the above procedures.
Secondary Connection Page
The Secondary Connection page (FIG. 93) sets the communication information for the installed
wireless interface card. This information includes its corresponding IP communication parameters,
wireless communication settings, and read the device number assigned to the Modero panel. Both
CV7 panels can use the NXA-WC80211B/CF wireless card for wireless communication. This card
also supports Wired Encryption Protocol (WEP) encryption of 64-bit and 128-bit key lengths. Refer
to both the Secondary Connection Page - Wireless Access Overview section on page 55 and
Configuring a Wireless Network Access section on page 57 for more detailed information of setting
up the Modero panel for wireless network access.
7" Modero Widescreen Touch Panels
105
Firmware Pages and Descriptions
IP Settings section
Wireless Settings section
Red fields are user-editable
Blue fields cycle through choices
Grey fields are read-only
Changes on this page
take effect after using
the BACK button to
return to the previous
page
FIG. 93 Secondary Connection page (showing default values)
The elements of the Secondary Connection page are described in the table below:
Secondary Connection Page Elements
Back:
Saves the changes and returns you to the previously active touch panel page.
Connection Status icon:
This visual display of the connection status allows the user to have a current
visual update of the panel’s connection status regardless of what page is
currently active.
• A Lock only appears on the icon if the panel has established a connection
with a currently secured target Master (requiring a username and password).
IP Settings:
DHCP/STATIC
Sets the IP communication values for the touch panel and contains:
Sets the panel to either DHCP or Static communication modes.
• DHCP (Dynamic Host Configuration Protocol) assigns IP Addresses to client
stations logging onto a TCP/IP network from a DHCP server.
• Static IP is a permanent IP Address that is assigned to a node in a TCP/IP
network.
Note: If DHCP is selected, the following fields become read-only: IP Address,
Subnet Mask, Gateway, Primary DNS, Secondary DNS, and Domain.
IP Address
Sets the secondary IP Address assigned to the panel.
Subnet Mask
Sets a subnetwork address to the panel.
• Subnetwork mask is the technique used by the IP protocol to filter messages
into a particular network segment (subnet).
Gateway
Sets a gateway value to the panel.
• Gateway is a computer that either performs protocol conversion between
different types of networks/applications or acts as a go-between for two or
more networks that use the same protocols.
Host Name
Sets the host name of the panel.
• PRIMARY DNS sets the address of the primary DNS server being used by the
Modero panel for host name lookups.
- DNS (Domain Name System) is software that lets users locate computers
on a local network or the Internet (TCP/IP network) by host and domain. The
DNS server maintains a database of host names for its’ domain and their
corresponding IP Addresses.
• SECONDARY DNS sets the secondary DNS value to the panel.
106
Primary DNS
Sets the address of the primary DNS server used by the panel for host name
lookups.
Secondary DNS
Sets the secondary DNS value to the Modero panel.
Domain
Sets the unique name on the Internet to the panel for DNS look-up.
MAC Address
This value is factory set by the manufacturer of the wireless Ethernet card.
7" Modero Widescreen Touch Panels
Firmware Pages and Descriptions
Secondary Connection Page Elements (Cont.)
Access Point MAC
Address:
This value is factory set by the manufacturer of the Wireless Access Point
(WAP).
When communicating with a WAP200G enter the MAC Address (BSSID) of the
target WAP as the Access Point MAC Address. Refer to the WAP200G
Instruction Manual for more detailed information on the interaction between
these two product lines.
Wireless Settings:
Network Name (SSID)
Sets the communication values for the NXA-WC80211B/CF wireless interface
card installed within the Modero panel.
Provides the Service Set Identifier (SSID), required by the panel, before it is
permitted to join the wireless network. The SSID is the unique name used on
the WAP and assigned to all panels in a wireless network that are communicating to the same target WAP.
• It is case sensitive and must not exceed 32 characters, which may be any
keyboard character. Make sure this setting is the same for all points in your
wireless network.
• This unique string identifies the network and is the same string for all users on
the same network.
Authentication
CV7 panels only allow one mode: Open System.
• An Open system network allows connections from any client without
authenticating whether that client has permission to associate with the
network.
Encryption
Cycles through the available encryption options: Clear Text, WEP64, and
WEP128. Wired Equivalent Privacy is an 802.11 security protocol for wireless
networks. The WEP encryption method is designed to provide the "equivalent"
security available in wireline networks.
• Clear Text causes network packets to be sent out as unencrypted text.
• WEP64 enables WEP encryption at 64-bits. In this case all packets will be
transmitted with their contents encrypted using the Default WEP Key.
• WEP128 enables WEP encryption at 128-bits. All packets are transmitted with
their contents encrypted using the Default WEP Key.
• If the key is not the correct size, the system will resize it to match the
number of bits required for the WEP encryption mode selected.
7" Modero Widescreen Touch Panels
107
Firmware Pages and Descriptions
Secondary Connection Page Elements (Cont.)
Wireless Settings (Cont.):
Generate (Passphrase)
Pressing the Generate button displays an on-screen keyboard which allows
you to enter a passphrase and then AUTOMATICALLY generate all four WEP
keys which are compatible only among Modero panels.
• Note: The code key generator on Modero panels use the same key
generation formula. Therefore, this same Passphrase generates identical
keys when done on any Modero because they all use the same
Modero-specific generator. The Passphrase generator is case sensitive.
• Take these WEP keys and enter them into the target WAP. When also working
with multiple panels, these WEP Keys (identical across all Modero panels)
must be entered manually into the target WAP.
• Once all panels have been setup in this way, these WEP keys can then be
entered into the associated Wireless Access Point for ease of installation.
• The Passphrase generator is unique to Modero panels. The Key generator on
these Modero panels are specific and do not generate the same keys as
other external non-AMX wireless devices.
- Example: If you enter the word apple into the Passphrase generator on a
3rd-party Wireless Access Point, it comes back with 1a:2b:3c:4d:etc.
Entering the same apple in the Passphrase generator of any Modero panel
generates a different key: a1:b2:c3:d4:etc. Only AMX Modero panels
generate the same Current Key by using a unique Passphrase key
generation technology. A Current Key string, when generated anywhere
else, will not match those created on the Modero panels.
Note: The code key generator on Modero panels use the same key generation
formula. The passphrase generator is case sensitive.
Default Key
Cycles through the four available WEP key identifiers in order to select a WEP
key to use. As the Default Key value is altered (through selection) the
corresponding Current Key is displayed. Each of these corresponds to a WEP
key.
• This feature is useful for accessing different networks without having to
re-enter that networks’ WEP key.
• It is also sometimes used to set up a rotating key schedule to provide an extra
layer of security.
WEP Keys
This feature provides you with another level of security by selecting a Key value.
• A single button is available for each WEP key up to a maximum of four keys.
• Pushing any of these buttons brings up an on-screen keyboard. Keys should
be entered in hexadecimal notation. It is common practice for every two
characters (representing a single byte) to be separated by a colon.
• Press Done to accept any changes and save the new value.
• Ex: 01:0A:67:F3:56, although this is not necessary and the key may be
entered by omitting the colons. A 64-bit key will be 10 characters in length
while a 128-bit key will be 26 characters in length. The length of the key
entered determines the level of WEP encryption employed.
Either 64-bit or 128-bit.
• 128-bit keys may also be entered and are used if supported by the
internal wireless card.
Current Key
Displays the current WEP key in use. Keys may also be examined by touching
the key buttons and noting the keyboard initialization text.
• When working with a single panel and a single WAP, it is recommended that
you manually enter the Current Key from the WAP into the selected WEP Key.
• When working with a single WAP and multiple panels, it is recommended that
you generate a Current Key using the same passphrase on all panels and
then enter the panel-produced WEP key manually into the Wireless Access
Point.
108
7" Modero Widescreen Touch Panels
Firmware Pages and Descriptions
Secondary Connection Page Elements (Cont.)
Wireless Settings (Cont.):
Channel
The RF channel being used for connection to the WAP (read -only).
• This is determined through the WAP.
Link Quality
Displays the current quality of the link (as descriptive colored text) from the
wireless NIC to the Wireless Access Point in real time.
• The bargraph has been replaced with a descriptions: None, Poor, Fair,
Good, Very Good, and Excellent. Green color text indicates better
communication quality.
• It reports the quality of the signal over the air (direct sequence spread
spectrum). Even when the link quality is at its lowest you still have a
connection and with it the ability to transmit and receive data, even if at much
lower speeds.
Note: Both Link Quality and Signal Strength are applicable to the RF
connection only. It is quite possible to have an RF signal to a Wireless Access
Point but be unable to communicate with it because of either incorrect IP or
encryption settings.
Signal Strength
SNR (Signal Noise Ratio) is a measure of the relative strength of a wireless RF
connection. This indicator displays a description of the signal strength from the
Wireless Access Point connection.
• The bargraph has been replaced with a descriptions: None, Poor, Fair,
Good, Very Good, and Excellent. Green color text indicates better signal
strength.
• Given this value and the link quality above, a user can determine the noise
level component of SNR.
Ex: If the signal strength is high but the link quality is low then the cause of the
link degradation is noise. However, if the signal strength is low and the link
quality is low the cause would simply be signal strength.
Data Rate
The data rate (in Mbps) at which the panel is currently communicating with a
target WAP at (dynamic).
• As you move closer to the target WAP (and both the signal strength/
quality), the data rate increases and as the quality degrades this rate
decreases.
• Data rates for 802.11b communication are: 1, 2, 5.5, and 11 Mbps.
• Ex: 802.11b has a max data rate is 11 Mbps.
System Connection Page
The System Connection page (FIG. 94) sets the Secondary DNS Address information with its
corresponding IP communication parameters, NetLinx Master communication settings, and reads
the device number assigned to the Modero panel.
IP Settings section
Master Connection section
(NetLinx Master properties)
Master Connection features are not
saved until the panel is rebooted
Red fields are user-editable
Blue fields cycle through choices
Grey fields are read-only
FIG. 94 System Connection page showing default values (reads and assigns values to the panel and Master)
7" Modero Widescreen Touch Panels
109
Firmware Pages and Descriptions
The elements of the System Connection page are described in the table below:
System Connection Page Elements
Back:
Saves the changes and returns you to the previously active touch panel page.
Connection Status icon:
This visual display of the connection status allows the user to have a current
visual update of the panel’s connection status regardless of what page is
currently active.
• A Lock only appears on the icon if the panel has established a connection
with a currently secured target Master (requiring a username and password).
IP Settings:
DHCP/Static
Sets the IP communication values for the panel and contains:
Sets the panel to either DHCP or Static communication modes.
• DHCP (Dynamic Host Configuration Protocol) assigns IP Addresses from
client stations logging onto a TCP/IP network via a DHCP server.
• Static IP is a permanent IP Address that is assigned to a node in a TCP/IP
network.
IP Address
Sets the secondary IP Address assigned to the panel.
Subnet Mask
Sets a subnetwork address to the panel.
• Subnetwork mask is the technique used by the IP protocol to filter messages
into a particular network segment (Subnet).
Gateway
Sets a gateway value to the panel.
• Gateway is a computer that either performs protocol conversion between
different types of networks/applications or acts as a go-between two or more
networks that use the same protocols.
Host Name
Sets the host name of the panel.
Primary DNS
Sets the address of the primary DNS server used for host name lookups.
• DNS (Domain Name System) is software that lets users locate computers on
a local network or the Internet (TCP/IP network) by host and domain. The
DNS server maintains a database of host names for its’ domain and their
corresponding IP Addresses.
Secondary DNS
Sets a secondary DNS value to the panel.
Domain
Sets the unique name on the Internet to the panel for DNS look-up.
• The panel belongs to the DNS domain.
Ethernet Mode
Sets the speed of the Ethernet connection to the panel.
• Choices are: Auto, 10 Half Duplex, 10 Full Duplex, 100 Half Duplex, or
100 Full Duplex.
MAC Address
110
Displays a read-only field that is factory set by AMX for the built-in Ethernet
interface.
7" Modero Widescreen Touch Panels
Firmware Pages and Descriptions
System Connection Page Elements (Cont.)
Master Connection:
Type
Sets the NetLinx Master communication values:
Sets the NetLinx Master to communicate with the panel via either USB or
Ethernet. This is based on the cable connection from the rear.
ICSNet is not a supported option on this panel.
• Ethernet is a CAT-5 cable (10/100Base T terminated in an RJ-45 connector)
used to network computers together and is used in most LAN (local area
networks). This description is also used to refer to both wired and wireless
communication.
• USB option cannot be used on Modero panels which are not equipped with a
rear USB port.
Mode
Cycles between the different connection modes (URL, Listen, and Auto)
(ETHERNET Only - disabled when USB is selected)
• URL - In this mode, enter the IP/URL, Master Port Number, and
username/password (if used) on the Master.
- The System Number field is read-only because the panel obtains this
information from the communicating Master.
• Listen - In this mode, add the Modero panel address into the URL List in
NetLinx Studio and set the connection mode to Listen. This mode allows the
Modero touch panel to "listen" for the Master’s communication signals.
- The System Number and Master IP/URL fields are red-only.
• Auto - In this mode, enter the System Number and a username/password
(if applicable). This mode is used when both the panel and the NetLinx
Master are on the same Subnet and the Master has its UDP feature enabled.
- Master IP/URL field is read-only.
System Number
Allows you to enter a system number. Default value is 0 (zero).
(ETHERNET Only - disabled when USB is selected)
Master IP/URL
Sets the Master IP or URL of the NetLinx Master.
(ETHERNET Only - disabled when USB is selected)
Master Port Number
Allows you to enter the port number used with the NetLinx Master.
• Default value is 1319. (ETHERNET Only - disabled when USB is selected)
Username/Password
7" Modero Widescreen Touch Panels
If the target Master has been previously secured, enter the alpha-numeric string
(into each field) assigned to a pre-configured user profile on the Master.
This profile should have the pre-defined level of access/configuration rights.
111
Firmware Pages and Descriptions
112
7" Modero Widescreen Touch Panels
Programming
Programming
You can program the touch panel, using the commands in this section, to perform a wide variety of
operations using Send_Commands and variable text commands.
A device must first be defined in the NetLinx programming language with values for the
Device: Port: System (in all programming examples - Panel is used in place of these values and
represents all Modero panels).
Verify you are using the latest NetLinx Master firmware. Verify the NetLinx Studio
program being used is version 2.3 or higher and TPD4 is version 2.5 or higher.
Button Assignments
• Button Channel Range: 1 - 4000 Button push and Feedback (per address port)
• Button Variable Text range: 1 - 4000 (per address port)
• Button States Range: 1 - 256
(0 = All states, for General buttons 1 = Off state and 2 = On state).
• Level Range: 1 - 600 (Default level value 0 - 255, can be set up to 1 - 65535)
• Address port Range: 1 - 100
These button assignments can only be adjusted in TPD4 and not on the panels
themselves.
Page Commands
These Page Commands are used in NetLinx Programming Language and are case insensitive.
Page Commands
@APG
Add a specific
popup page to a
specified popup
group.
Add the popup page to a group if it does not already exist. If the new popup is added to a
group which has a popup displayed on the current page along with the new pop-up, the
displayed popup will be hidden and the new popup will be displayed.
Syntax:
"'@APG-<popup page name>;<popup group name>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
popup group name = 1 - 50 ASCII characters. Name of the popup group.
Example:
SEND_COMMAND Panel,"'@APG-Popup1;Group1'"
Adds the popup page ’Popup1’ to the popup group ’Group1’.
@CPG
Syntax:
Clear all popup
pages from
specified popup
group.
Variable:
"'@CPG-<popup group name>'"
popup group name = 1 - 50 ASCII characters. Name of the popup group.
Example:
SEND_COMMAND Panel,"'@CPG-Group1'"
Clears all popup pages from the popup group ’Group1’.
7" Modero Widescreen Touch Panels
113
Programming
Page Commands (Cont.)
@DPG
Syntax:
Delete a specific
popup page from
specified popup
group if it exists.
Variable:
"'@DPG-<popup page name>;<popup group name>'"
popup page name = 1 - 50 ASCII characters. Name of the popup page.
popup group name = 1 - 50 ASCII characters. Name of the popup group.
Example:
SEND_COMMAND Panel,"'@DPG-Popup1;Group1'"
Deletes the popup page ’Popup1’ from the popup group ’Group1’.
@PDR
If the flag is set, the popup will return to its default location on show instead of its last drag
location.
Set the popup
location reset flag. Syntax:
"'@PDR-<popup page name>;<reset flag>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed
On.
reset flag = 1 = Enable reset flag
0 = Disable reset flag
Example:
SEND_COMMAND Panel,"'@PDR-Popup1;1'"
Popup1 will return to its default location when turned On.
@PHE
Syntax:
Set the hide effect
"'@PHE-<popup page name>;<hide effect name>'"
for the specified
Variable:
popup page to the
named hide effect. popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed
On.
hide effect name = Refers to the popup effect names being used.
Example:
SEND_COMMAND Panel,"'@PHE-Popup1;Slide to Left'"
Sets the Popup1 hide effect name to ’Slide to Left’.
@PHP
Only 1 coordinate is ever needed for an effect; however, the command will specify both.
Set the hide effect This command sets the location at which the effect will end at.
position.
Syntax:
"'@PHP-<popup page name>;<x coordinate>,<y coordinate>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed
On.
Example:
SEND_COMMAND Panel,"'@PHP-Popup1;75,0'"
Sets the Popup1 hide effect x-coordinate value to 75 and the y-coordinate value to 0.
@PHT
Syntax:
Set the hide effect
"'@PHT-<popup page name>;<hide effect time>'"
time for the
Variable:
specified popup
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed
page.
On.
hide effect time = Given in 1/10ths of a second.
Example:
SEND_COMMAND Panel,"'@PHT-Popup1;50'"
Sets the Popup1 hide effect time to 5 seconds.
114
7" Modero Widescreen Touch Panels
Programming
Page Commands (Cont.)
@PPA
Close all popups
on a specified
page.
If the page name is empty, the current page is used. Same as the ’Clear Page’ command
in TPDesign4.
Syntax:
"'@PPA-<page name>'"
Variable:
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'@PPA-Page1'"
Close all popups on Page1.
@PPF
Deactivate a
specific popup
page on either a
specified page or
the current page.
If the page name is empty, the current page is used (see example 2). If the popup page is
part of a group, the whole group is deactivated. This command works in the same way as
the ’Hide Popup’ command in TPDesign4.
Syntax:
"'@PPF-<popup page name>;<page name>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'@PPF-Popup1;Main'"
Deactivates the popup page ’Popup1’ on the Main page.
Example 2:
SEND_COMMAND Panel,"'@PPF-Popup1'"
Deactivates the popup page ’Popup1’ on the current page.
@PPG
Toggle a
specific popup
page on either a
specified page or
the current page.
If the page name is empty, the current page is used (see example 2). Toggling refers to the
activating/deactivating (On/Off) of a popup page. This command works in the same way
as the ’Toggle Popup’ command in TPDesign4.
Syntax:
"'@PPG-<popup page name>;<page name>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'@PPG-Popup1;Main'"
Toggles the popup page ’Popup1’ on the ’Main’ page from one state to another (On/Off).
Example 2:
SEND_COMMAND Panel,"'@PPG-Popup1'"
Toggles the popup page ’Popup1’ on the current page from one state to another (On/Off).
@PPK
Kill a specific
popup page from
all pages.
Kill refers to the deactivating (Off) of a popup window from all pages. If the pop-up page is
part of a group, the whole group is deactivated. This command works in the same way as
the 'Clear Group' command in TPDesign 4.
Syntax:
"'@PPK-<popup page name>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
Example:
SEND_COMMAND Panel,"'@PPK-Popup1'"
Kills the popup page ’Popup1’ on all pages.
7" Modero Widescreen Touch Panels
115
Programming
Page Commands (Cont.)
@PPM
Set the modality
of a specific
popup page to
Modal or
NonModal.
A Modal popup page, when active, only allows you to use the buttons and features on that
popup page. All other buttons on the panel page are inactivated.
Syntax:
"'@PPM-<popup page name>;<mode>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
mode = NONMODAL converts a previously Modal popup page to a NonModal.
MODAL converts a previously NonModal popup page to Modal.
modal = 1 and non-modal = 0
Example:
SEND_COMMAND Panel,"'@PPM-Popup1;Modal'"
Sets the popup page ’Popup1’ to Modal.
SEND_COMMAND Panel,"'@PPM-Popup1;1'"
Sets the popup page ’Popup1’ to Modal.
@PPN
Activate a
specific popup
page to launch on
either a specified
page or the
current page.
If the page name is empty, the current page is used (see example 2). If the popup page is
already on, do not re-draw it. This command works in the same way as the ’Show Popup’
command in TPDesign4.
Syntax:
"'@PPN-<popup page name>;<page name>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'@PPN-Popup1;Main'"
Activates ’Popup1’ on the ’Main’ page.
Example 2:
SEND_COMMAND Panel,"'@PPN-Popup1'"
Activates the popup page ’Popup1’ on the current page.
@PPT
If timeout is empty, popup page will clear the timeout.
Set a specific
popup page to
timeout within a
specified time.
Syntax:
"'@PPT-<popup page name>;<timeout>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
timeout = Timeout duration in 1/10ths of a second.
Example:
SEND_COMMAND Panel,"'@PPT-Popup1;30'"
Sets the popup page ’Popup1’ to timeout within 3 seconds.
@PPX
This command works in the same way as the 'Clear All' command in TPDesign 4.
Close all
popups on all
pages.
Syntax:
"'@PPX'"
Example:
SEND_COMMAND Panel,"'@PPX'"
Close all popups on all pages.
116
7" Modero Widescreen Touch Panels
Programming
Page Commands (Cont.)
@PSE
Set the show
effect for the
specified popup
page to the
named show
effect.
Syntax:
"'@PSE-<popup page name>;<show effect name>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed
On.
show effect name = Refers to the popup effect name being used.
Example:
SEND_COMMAND Panel,"'@PSE-Popup1;Slide from Left'"
Sets the Popup1 show effect name to ’Slide from Left’.
@PSP
Set the show
effect position.
Only 1 coordinate is ever needed for an effect; however, the command will specify both.
This command sets the location at which the effect will begin at.
Syntax:
"'@PSP-<popup page name>;<x coordinate>,<y coordinate>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed
On.
Example:
SEND_COMMAND Panel,"'@PSP-Popup1;100,0'"
Sets the Popup1 show effect x-coordinate value to 100 and the y-coordinate value to 0.
@PST
Syntax:
Set the show
effect time for the
specified popup
page.
Variable:
"'@PST-<popup page name>;<show effect time>'"
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed
On.
show effect time = Given in 1/10ths of a second.
Example:
SEND_COMMAND Panel,"'@PST-Popup1;50'"
Sets the Popup1 show effect time to 5 seconds.
PAGE
Flip to a specified
page.
Flips to a page with a specified page name. If the page is currently active, it will not redraw
the page.
Syntax:
"'PAGE-<page name>'"
Variable:
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'PAGE-Page1'"
Flips to page1.
7" Modero Widescreen Touch Panels
117
Programming
Page Commands (Cont.)
PPOF
Deactivate a
specific popup
page on either a
specified page or
the current page.
If the page name is empty, the current page is used (see example 2). If the popup page is
part of a group, the whole group is deactivated. This command works in the same way as
the ’Hide Popup’ command in TPDesign4.
Syntax:
"'PPOF-<popup page name>;<page name>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'PPOF-Popup1;Main'"
Deactivates the popup page ’Popup1’ on the Main page.
Example 2:
SEND_COMMAND Panel,"'PPOF-Popup1'"
Deactivates the popup page ’Popup1’ on the current page.
PPOG
Toggle a
specific popup
page on either a
specified page or
the current page.
If the page name is empty, the current page is used (see example 2). Toggling refers to the
activating/deactivating (On/Off) of a popup page. This command works in the same way
as the ’Toggle Popup’ command in TPDesign4.
Syntax:
"'PPOG-<popup page name>;<page name>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'PPOG-Popup1;Main'"
Toggles the popup page ’Popup1’ on the Main page from one state to another (On/Off).
Example 2:
SEND_COMMAND Panel,"'PPOG-Popup1'"
Toggles the popup page ’Popup1’ on the current page from one state to another (On/Off).
PPON
Activate a
specific popup
page to launch on
either a specified
page or the
current page.
If the page name is empty, the current page is used (see example 2). If the popup page is
already On, do not re-draw it. This command works in the same way as the ’Show Popup’
command in TPDesign4.
Syntax:
"'PPON-<popup page name>;<page name>'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'PPON-Popup1; Main'"
Activates the popup page ’Popup1’ on the Main page.
Example 2:
SEND_COMMAND Panel,"'PPON-Popup1'"
Activates the popup page ’Popup1’ on the current page.
118
7" Modero Widescreen Touch Panels
Programming
Programming Numbers
The following information provides the programming numbers for colors, fonts, and borders.
Colors can be used to set the colors on buttons, sliders, and pages. The lowest color number
represents the lightest color-specific display; the highest number represents the darkest display. For
example, 0 represents light red, and 5 is dark red.
RGB triplets and names for basic 88 colors
RGB Values for all 88 Basic Colors
Index No.
Name
Red
Green
Blue
00
Very Light Red
255
0
0
01
Light Red
223
0
0
02
Red
191
0
0
03
Medium Red
159
0
0
04
Dark Red
127
0
0
05
Very Dark Red
95
0
0
06
Very Light Orange
255
128
0
07
Light Orange
223
112
0
08
Orange
191
96
0
09
Medium Orange
159
80
0
10
Dark Orange
127
64
0
11
Very Dark Orange
95
48
0
12
Very Light Yellow
255
255
0
13
Light Yellow
223
223
0
14
Yellow
191
191
0
15
Medium Yellow
159
159
0
16
Dark Yellow
127
127
0
17
Very Dark Yellow
95
95
0
18
Very Light Lime
128
255
0
19
Light Lime
112
223
0
20
Lime
96
191
0
21
Medium Lime
80
159
0
22
Dark Lime
64
127
0
23
Very Dark Lime
48
95
0
24
Very Light Green
0
255
0
25
Light Green
0
223
0
26
Green
0
191
0
27
Medium Green
0
159
0
28
Dark Green
0
127
0
29
Very Dark Green
0
95
0
30
Very Light Mint
0
255
128
31
Light Mint
0
223
112
32
Mint
0
191
96
33
Medium Mint
0
159
80
34
Dark Mint
0
127
64
35
Very Dark Mint
0
95
48
7" Modero Widescreen Touch Panels
119
Programming
RGB Values for all 88 Basic Colors (Cont.)
120
Index No.
Name
Red
Green
Blue
36
Very Light Cyan
0
255
255
37
Light Cyan
0
223
223
38
Cyan
0
191
191
39
Medium Cyan
0
159
159
40
Dark Cyan
0
127
127
41
Very Dark Cyan
0
95
95
42
Very Light Aqua
0
128
255
43
Light Aqua
0
112
223
44
Aqua
0
96
191
45
Medium Aqua
0
80
159
46
Dark Aqua
0
64
127
47
Very Dark Aqua
0
48
95
48
Very Light Blue
0
0
255
49
Light Blue
0
0
223
50
Blue
0
0
191
51
Medium Blue
0
0
159
52
Dark Blue
0
0
127
53
Very Dark Blue
0
0
95
54
Very Light Purple
128
0
255
55
Light Purple
112
0
223
56
Purple
96
0
191
57
Medium Purple
80
0
159
58
Dark Purple
64
0
127
59
Very Dark Purple
48
0
95
60
Very Light Magenta
255
0
255
61
Light Magenta
223
0
223
62
Magenta
191
0
191
63
Medium Magenta
159
0
159
64
Dark Magenta
127
0
127
65
Very Dark Magenta
95
0
95
66
Very Light Pink
255
0
128
67
Light Pink
223
0
112
68
Pink
191
0
96
69
Medium Pink
159
0
80
70
Dark Pink
127
0
64
71
Very Dark Pink
95
0
48
72
White
255
255
255
73
Grey1
238
238
238
74
Grey3
204
204
204
75
Grey5
170
170
170
76
Grey7
136
136
136
77
Grey9
102
102
102
78
Grey4
187
187
187
79
Grey6
153
153
153
7" Modero Widescreen Touch Panels
Programming
RGB Values for all 88 Basic Colors (Cont.)
Index No.
Name
Red
Green
Blue
80
Grey8
119
119
119
81
Grey10
85
85
85
82
Grey12
51
51
51
83
Grey13
34
34
34
84
Grey2
221
221
221
85
Grey11
68
68
68
86
Grey14
17
17
17
87
Black
0
0
0
255
TRANSPARENT
99
53
99
Font styles and ID numbers
Font styles can be used to program the text fonts on buttons, sliders, and pages. The following chart
shows the default font type and their respective ID numbers generated by TPDesign4.
Default Font Styles and ID Numbers
Font ID # Font type
Size
Font ID # Font type
Size
1
Courier New
9
19
Arial
9
2
Courier New
12
20
Arial
10
3
Courier New
18
21
Arial
12
4
Courier New
26
22
Arial
14
5
Courier New
32
23
Arial
16
6
Courier New
18
24
Arial
18
7
Courier New
26
25
Arial
20
8
Courier New
34
26
Arial
24
9
AMX Bold
14
27
Arial
36
10
AMX Bold
20
28
Arial Bold
10
11
AMX Bold
36
29
Arial Bold
8
32 - Variable Fonts start at 32.
You must import fonts into a TPDesign4 project file. The font ID numbers are
assigned by TPDesign4. These values are also listed in the
Generate Programmer’s Report.
7" Modero Widescreen Touch Panels
121
Programming
Border styles and Programming numbers
Border styles can be used to program borders on buttons, sliders, and popup pages.
Border Styles and Programming Numbers
No.
Border styles
No.
Border styles
0-1
No border
10-11
Picture frame
2
Single line
12
Double line
3
Double line
20
Bevel-S
4
Quad line
21
Bevel-M
5-6
Circle 15
22-23
Circle 15
7
Single line
24-27
Neon inactive-S
8
Double line
40-41
Diamond 55
9
Quad line
The TPDesign4 Touch Panel Design program has pre-set border styles that are user selectable.
You cannot use the following number values for programming purposes when changing border
styles. TPD4 border styles can ONLY be changed by using the name.
TPD4 Border Styles by Name
122
No.
Border styles
No.
Border styles
1
None
22
Circle 155
2
AMX Elite -L
23
Circle 165
3
AMX Elite -M
24
Circle 175
4
AMX Elite -S
25
Circle 185
5
Bevel -L
26
Circle 195
6
Bevel -M
27
Cursor Bottom
7
Bevel -S
28
Cursor Bottom with Hole
8
Circle 15
29
Cursor Top
9
Circle 25
30
Cursor Top with Hole
10
Circle 35
31
Cursor Left
11
Circle 45
32
Cursor Left with Hole
12
Circle 55
33
Cursor Right
13
Circle 65
34
Cursor Right with Hole
14
Circle 75
35
Custom Frame
15
Circle 85
36
Diamond 15
16
Circle 95
37
Diamond 25
17
Circle 105
38
Diamond 35
18
Circle 115
39
Diamond 45
19
Circle 125
40
Diamond 55
20
Circle 135
41
Diamond 65
21
Circle 145
42
Diamond 75
7" Modero Widescreen Touch Panels
Programming
TPD4 Border Styles by Name (Cont.)
No.
Border styles
No.
Border styles
43
Diamond 85
85
Menu Bottom Rounded 65
44
Diamond 95
86
Menu Bottom Rounded 75
45
Diamond 105
87
Menu Bottom Rounded 85
46
Diamond 115
88
Menu Bottom Rounded 95
47
Diamond 125
89
Menu Bottom Rounded 105
48
Diamond 135
90
Menu Bottom Rounded 115
49
Diamond 145
91
Menu Bottom Rounded 125
50
Diamond 155
92
Menu Bottom Rounded 135
51
Diamond 165
93
Menu Bottom Rounded 145
52
Diamond 175
94
Menu Bottom Rounded 155
53
Diamond 185
95
Menu Bottom Rounded 165
54
Diamond 195
96
Menu Bottom Rounded 175
55
Double Bevel -L
97
Menu Bottom Rounded 185
56
Double Bevel -M
98
Menu Bottom Rounded 195
57
Double Bevel -S
99
Menu Top Rounded 15
58
Double Line
100
Menu Top Rounded 25
59
Fuzzy
101
Menu Top Rounded 35
60
Glow-L
102
Menu Top Rounded 45
61
Glow-S
103
Menu Top Rounded 55
62
Help Down
104
Menu Top Rounded 65
63
Neon Active -L
105
Menu Top Rounded 75
64
Neon Active -S
106
Menu Top Rounded 85
65
Neon Inactive -L
107
Menu Top Rounded 95
66
Neon Inactive -S
108
Menu Top Rounded 105
67
Oval H 60x30
109
Menu Top Rounded 115
68
Oval H 100x50
110
Menu Top Rounded 125
69
Oval H 150x75
111
Menu Top Rounded 135
70
Oval H 200x100
112
Menu Top Rounded 145
71
Oval V 30x60
113
Menu Top Rounded 155
72
Oval V 50x100
114
Menu Top Rounded 165
73
Oval V 75x150
115
Menu Top Rounded 175
74
Oval V 100x200
116
Menu Top Rounded 185
75
Picture Frame
117
Menu Top Rounded 195
76
Quad Line
118
Menu Right Rounded 15
77
Single Line
119
Menu Right Rounded 25
78
Windows Style Popup
120
Menu Right Rounded 35
79
Windows Style Popup (Status Bar)
121
Menu Right Rounded 45
80
Menu Bottom Rounded 15
122
Menu Right Rounded 55
81
Menu Bottom Rounded 25
123
Menu Right Rounded 65
82
Menu Bottom Rounded 35
124
Menu Right Rounded 75
83
Menu Bottom Rounded 45
125
Menu Right Rounded 85
84
Menu Bottom Rounded 55
126
Menu Right Rounded 95
7" Modero Widescreen Touch Panels
123
Programming
TPD4 Border Styles by Name (Cont.)
No.
Border styles
No.
Border styles
127
Menu Right Rounded 105
145
Menu Left Rounded 95
128
Menu Right Rounded 115
146
Menu Left Rounded 105
129
Menu Right Rounded 125
147
Menu Left Rounded 115
130
Menu Right Rounded 135
148
Menu Left Rounded 125
131
Menu Right Rounded 145
149
Menu Left Rounded 135
132
Menu Right Rounded 155
150
Menu Left Rounded 145
133
Menu Right Rounded 165
151
Menu Left Rounded 155
134
Menu Right Rounded 175
152
Menu Left Rounded 165
135
Menu Right Rounded 185
153
Menu Left Rounded 175
136
Menu Right Rounded 195
154
Menu Left Rounded 185
137
Menu Left Rounded 15
155
Menu Left Rounded 195
138
Menu Left Rounded 25
139
Menu Left Rounded 35
140
Menu Left Rounded 45
141
Menu Left Rounded 55
142
Menu Left Rounded 65
143
Menu Left Rounded 75
144
Menu Left Rounded 85
"^" Button Commands
These Button Commands are used in NetLinx Studio and are case insensitive.
All commands that begin with "^" have the capability of assigning a variable text address range and
button state range. A device must first be defined in the NetLinx programming language with
values for the Device: Port : System (in all programming examples - Panel is used in place of
these values).
Variable text ranges allow you to target 1 or more variable text channels in a single
command.
Button State ranges allow you to target 1 or more states of a variable text button with a
single command.
"." Character is used for the 'through' notation, also the "&" character is used for the
'And' notation.
124
7" Modero Widescreen Touch Panels
Programming
"^" Button Commands
^ANI
Syntax:
Run a button
animation
(in 1/10 second).
Variable:
"'^ANI-<vt addr range>,<start state>,<end state>,<time>'"
variable text address range = 1 - 4000.
start state = Beginning of button state (0= current state).
end state = End of button state.
time = In 1/10 second intervals.
Example:
SEND_COMMAND Panel,"'^ANI-500,1,25,100'"
Runs a button animation at text range 500 from state 1 to state 25 for 10 second.
^APF
Add page flip
action to a button
if it does not
already exist.
Syntax:
"'^APF-<vt addr range>,<page flip action>,<page name>'"
Variable:
variable text address range = 1 - 4000.
page flip action =
Stan[dardPage] - Flip to standard page
Prev[iousPage] - Flip to previous page
Show[Popup] - Show Popup page
Hide[Popup] - Hide Popup page
Togg[lePopup] - Toggle popup state
ClearG[roup] - Clear popup page group from all pages
ClearP[age] - Clear all popup pages from a page with the
specified page name
ClearA[ll] - Clear all popup pages from all pages
page name = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'^APF-400,Stan,Main Page'"
Assigns a button to a standard page flip with page name 'Main Page'.
^BAT
Append
non-unicode text.
Syntax:
"'^BAT-<vt addr range>,<button states range>,<new text>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
new text = 1 - 50 ASCII characters.
Example:
SEND_COMMAND Panel,"'^BAT-520,1,Enter City'"
Appends the text 'Enter City' to the button’s OFF state.
^BAU
Same format as ^UNI.
Append
unicode text.
Syntax:
"'^BAU-<vt addr range>,<button states range>,<unicode
text>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
unicode text = 1 - 50 ASCII characters. Unicode characters must be entered in Hex
format.
Example:
SEND_COMMAND Panel,"'^BAU-520,1,00770062'"
Appends Unicode text '00770062' to the button’s OFF state.
7" Modero Widescreen Touch Panels
125
Programming
"^" Button Commands (Cont.)
^BCB
Only if the specified border color is not the same as the current color.
Set the border
color to the
specified color.
Note: Color can be assigned by color name (without spaces), number or R,G,B value
(RRGGBB or RRGGBBAA).
Syntax:
"'^BCB-<vt addr range>,<button states range>,<color
value>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
color value = Refer to the RGB Values for all 88 Basic Colors table on page 119 for more
information.
Example:
SEND_COMMAND Panel,"'^BCB-500.504&510,1,12'"
Sets the Off state border color to 12 (Yellow). Colors can be set by Color Numbers, Color
name, R,G,B,alpha colors (RRGGBBAA) and R, G & B colors values (RRGGBB).
Refer to the RGB Values for all 88 Basic Colors table on page 119.
^BCF
Only if the specified fill color is not the same as the current color.
Set the fill color to
the specified
color.
Note: Color can be assigned by color name (without spaces), number or R,G,B value
(RRGGBB or RRGGBBAA).
Syntax:
"'^BCF-<vt addr range>,<button states range>,<color
value>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
color value = Refer to the RGB Values for all 88 Basic Colors table on page 119 for more
information.
Example:
SEND_COMMAND Panel,"'^BCF-500.504&510.515,1,12'"
SEND_COMMAND Panel,"'^BCF-500.504&510.515,1,Yellow'"
SEND_COMMAND Panel,"'^BCF-500.504&510.515,1,#F4EC0A63''"
SEND_COMMAND Panel,"'^BCF-500.504&510.515,1,#F4EC0A'"
Sets the Off state fill color by color number. Colors can be set by Color Numbers, Color
name, R,G,B,alpha colors (RRGGBBAA) and R, G & B colors values (RRGGBB).
126
7" Modero Widescreen Touch Panels
Programming
"^" Button Commands (Cont.)
^BCT
Only if the specified text color is not the same as the current color.
Set the text color
to the specified
color.
Note: Color can be assigned by color name (without spaces), number or R,G,B value
(RRGGBB or RRGGBBAA).
Syntax:
"'^BCT-<vt addr range>,<button states range>,<color
value>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
color value = Refer to the RGB Values for all 88 Basic Colors table on page 119 for more
information.
Example:
SEND_COMMAND Panel,"'^BCT-500.504&510,1,12'"
Sets the Off state border color to 12 (Yellow). Colors can be set by Color Numbers, Color
name, R,G,B,alpha colors (RRGGBBAA) and R, G & B colors values (RRGGBB).
^BDO
Determines what order each layer of the button is drawn.
Set the button
draw order.
Syntax:
"'^BDO-<vt addr range>,<button states range>,<1-5><1-5><15><1-5><1-5>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
layer assignments = Fill Layer
=1
Image Layer = 2
Icon Layer = 3
Text Layer = 4
Border Layer = 5
Note: The layer assignments are from bottom to top. The default draw order is 12345.
Example:
SEND_COMMAND Panel,"'^BDO-530,1&2,51432'"
Sets the button’s variable text 530 ON/OFF state draw order (from bottom to top) to
Border, Fill, Text, Icon, and Image.
Example 2:
SEND_COMMAND Panel,"'^BDO-1,0,12345'"
Sets all states of a button back to its default drawing order.
^BFB
ONLY works on General-type buttons.
Set the feedback Syntax:
type of the button.
"'^BFB-<vt addr range>,<feedback type>'"
Variable:
variable text address range = 1 - 4000.
feedback type = (None, Channel, Invert, On (Always on), Momentary, and Blink).
Example:
SEND_COMMAND Panel,"'^BFB-500,Momentary'"
Sets the Feedback type of the button to 'Momentary'.
7" Modero Widescreen Touch Panels
127
Programming
"^" Button Commands (Cont.)
^BIM
Syntax:
Set the input
"'^BIM-<vt addr range>,<input mask>'"
mask for the
Variable:
specified address.
variable text address range = 1 - 4000.
input mask = Refer to the Text Area Input Masking section on page 170 for character
types.
Example:
SEND_COMMAND Panel,"'^BIM-500,AAAAAAAAAA'"
Sets the input mask to ten ’A’ characters, that are required, to either a letter or digit
(entry is required).
^BLN
The maximum number of lines to remove is 240. A value of 0 will display the incoming
video signal unaffected. This command is used to scale non 4x3 video images into non
4x3 video buttons.
Set the number of
lines removed
Syntax:
equally from the
top and bottom of
"'^BLN-<vt addr range>,<button states range>,<number of
a composite video
lines>'"
signal.
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
number of lines = 0 - 240.
Example:
SEND_COMMAND Panel,"'^BLN-500,55'"
Equally removes 55 lines from the top and 55 lines from the bottom of the video button.
128
7" Modero Widescreen Touch Panels
Programming
"^" Button Commands (Cont.)
^BMC
Button copy
command.
Copy attributes of
the source button
to all the
destination
buttons.
Note that the source is a single button state. Each state must be copied as a separate
command. The <codes> section represents what attributes will be copied. All codes are
2 char pairs that can be separated by comma, space, percent or just ran together.
Syntax:
"'^BMC-<vt addr range>,<button states range>,<source
port>,<source address>,<source state>,<codes>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
source port = 1 - 100.
source address = 1 - 4000.
source state = 1 - 256.
codes: BM - Picture/Bitmap
BR - Border
CB - Border Color
CF - Fill Color
CT - Text Color
EC - Text effect color
EF - Text effect
FT - Font
IC - Icon
JB - Bitmap alignment
JI - Icon alignment
JT - Text alignment
LN - Lines of video removed
OP - Opacity
SO - Button Sound
TX - Text
VI - Video slot ID
WW - Word wrap on/off
Example:
SEND_COMMAND Panel,"'^BMC-425,1,1,500,1,BR'"
or
SEND_COMMAND Panel,"'^BMC-425,1,1,500,1,%BR'"
Copies the OFF state border of button with a variable text address of 500 onto the OFF
state border of button with a variable text address of 425.
Example 2:
SEND_COMMAND Panel,"'^BMC150,1,1,315,1,%BR%FT%TX%BM%IC%CF%CT'"
Copies the OFF state border, font, Text, bitmap, icon, fill color and text color of the button
with a variable text address of 315 onto the OFF state border, font, Text, bitmap, icon, fill
color and text color of the button with a variable text address of 150.
7" Modero Widescreen Touch Panels
129
Programming
"^" Button Commands (Cont.)
^BMF
Set any/all button
parameters by
sending
embedded codes
and data.
Syntax:
"'^BMF-<vt addr range>,<button states range>,<data>'"
Variables:
variable text address char array = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
level range = 1 - 600 (level value is 1 - 65535).
data:
’%R<left>,<top>,<right>,<bottom>’’ = Set Recetangle.
’%B<border style>’ = Set the border style name. See the Border Styles and
Programming Numbers table on page 122.
’%B’,<border 0-27,40,41> = Set the borer style number. See the Border Styles and
Programming Numbers table on page 122.
’%DO<1-5><1-5><1-5><1-5><1-5> = Set the draw order. Listed from bottom to top.
Refer to the ^BDO command on page 127 for more information.
’%F’,<font 1-8,10,11,20-29,32-xx> = Set the font. See the Default Font Styles and ID
Numbers table on page 121.
’%F<font 01-08,10,11,20-29,32-xx>’ = Set the font. See the Default Font Styles and ID
Numbers table on page 121.
’%MI<mask image>’ = Set the mask image. Refer to the ^BMI command on page 132 for
more information.
’%T<text >’ = Set the text using ASCII characters (empty is clear).
’%P<bitmap>’ = Set the picture/bitmap filename (empty is clear).
’%I’,<icon 01-9900, 0-clear>’ = Set the icon using values of 01 - 9900 (icon numbers are
assigned in the TPDesign4 Resource Manager tab - Slots section).
’%I<icon 01-9900, 0-clear>’ = Set the icon using values of 01 - 9900 (icon numbers are
assigned in the TPDesign4 Resource Manager tab - Slots section).
’%J’,<alignment of text 1-9> = As shown the following telephone keypad alignment chart:
0
1
2
3
4
5
6
7
8
9
Zero can be used for an absolute position
’%JT<alignment of text 0-9>’ = As shown the above telephone keypad alignment chart,
BUT the 0 (zero) is absolute and followed by ’,<left>,<top>’
’%JB<alignment of bitmap/picture 0-9>’ = As shown the above telephone keypad
alignment chart BUT the 0 (zero) is absolute and followed by ’,<left>,<top>’
’%JI<alignment of icon 0-9>’ = As shown the above telephone keypad alignment chart,
BUT the 0 (zero) is absolute and followed by ’,<left>,<top>’
130
7" Modero Widescreen Touch Panels
Programming
"^" Button Commands (Cont.)
^BMF
(Cont.)
For some of these commands and values, refer to the RGB Values for all 88 Basic
Colors table on page 119.
’%CF<on fill color>’ = Set Fill Color.
’%CB<on border color>’ = Set Border Color.
’%CT<on text color>’ = Set Text Color.
’%SW<1 or 0>’ = Show/hide a button.
’%ST<style>’ = Button style.
’%SO<sound>’ = Set the button sound.
’%EN<1 or 0>’ = Enable/disable a button.
’%WW<1 or 0>’ = Word wrap On/Off.
’%GH<bargraph hi>’ = Set the bargraph upper limit.
’%GL<bargraph low>’ = Set the bargraph lower limit.
’%GN<bargraph slider name>’ = Set the bargraph slider name/Joystick cursor name.
’%GC<bargraph slider color>’ = Set the bargraph slider color/Joystick cursor color.
’%GI<bargraph invert>’ = Set the bargraph invert/noninvert or joystick coordinate
(0,1,2,3). See the ^GIV command on page 138 for more information.
’%GU<bargraph ramp up>’ = Set the bargraph ramp up time in intervals of 1/10 second.
’%GD<bargraph ramp down>’ = Set the bargraph ramp down time in 1/10 second.
’%GG<bargraph drag increment> = Set the bargraph drag increment. Refer to the ^GDI
command on page 138 for more information.
’%VI<video ON/OFF>’ = Set the Video either ON (value=1) or OFF (value=0).
’%OT<feedback type>’ = Set the Feedback (Output) Type to one of the following:
None, Channel,Invert, ON (Always ON), Momentary, or Blink.
’%SM’ = Submit a text for text area button.
’%SF<1 or 0>’ = Set the focus for text area button.
’%OP<0-255>’ = Set the button opacity to either Invisible (value=0) or Opaque
(value=255).
’%OP#<00-FF>’ = Set the button opacity to either Invisible (value=00) or Opaque
(value=FF).
’%UN<Unicode text>’ = Set the Unicode text. See the ^UNI section on page 143 for the
text format.
’%LN<0-240>’ = Set the lines of video being removed. See the ^BLN section on
page 128 for more information.
’%EF<text effect name>’ = Set the text effect.
’%EC<text effect color>’ = Set the text effect color.
’%ML<max length>’ = Set the maximum length of a text area.
’%MK<input mask>’ = Set the input mask of a text area.
’%VL<0-1>’ = Log-On/Log-Off the computer control connection
’%VN<network name>’ = Set network connection name.
’%VP<password>’ = Set the network connection password.
Example:
SEND_COMMAND Panel,"'^BMF-500,1,%B10%CFRed%CB Blue
%CTBlack%Ptest.png'"
Sets the button OFF state as well as the Border, Fill Color, Border Color, Text Color, and
Bitmap.
7" Modero Widescreen Touch Panels
131
Programming
"^" Button Commands (Cont.)
^BMI
Set the button
mask image.
Mask image is used to crop a borderless button to a non-square shape. This is typically
used with a bitmap.
Syntax:
"'^BMI-<vt addr range>,<button states range>,<mask
image>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
mask image = Graphic file used.
Example:
SEND_COMMAND Panel,"'^BMI-530,1&2,newMac.png'"
Sets the button with variable text 530 ON/OFF state mask image to 'newmac.png'.
^BML
Set the maximum
length of the text
area button.
If this value is set to zero (0) there is no max length. The maximum length available is
2000. This is only for a Text area input button and not for a Text area input masking button.
Syntax:
"'^BML-<vt addr range>,<max length>'"
Variable:
variable text address range = 1 - 4000.
max length = 2000 (0=no max length).
Example:
SEND_COMMAND Panel,"'^BML-500,20'"
Sets the maximum length of the text area input button to 20 characters.
^BMP
Syntax:
Assign a picture to
"'^BMP-<vt addr range>,<button states range>,<name of
those buttons with
bitmap/picture>'"
a defined address
Variable:
range.
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
name of bitmap/picture = 1 - 50 ASCII characters.
Example:
SEND_COMMAND Panel,"'^BMP-500.504&510.515,1,bitmap.png'"
Sets the OFF state picture for the buttons with variable text ranges of 500-504 & 510-515.
^BNC
Clear current
TakeNote
annotations.
Syntax:
"'^BNC-<vt addr range>,<command value>'"
Variable:
variable text address range = 1 - 4000.
command value = (0= clear, 1= clear all).
Example:
SEND_COMMAND Panel,"'^BNC-973,0'"
Clears the annotation of the TakeNote button with variable text 973.
132
7" Modero Widescreen Touch Panels
Programming
"^" Button Commands (Cont.)
^BNN
Syntax:
Set the TakeNote
network name for
the specified
Addresses.
Variable:
"'^BNN-<vt addr range>,<network name>'"
variable text address range = 1 - 4000.
network name = Use a valid IP Address.
Example:
SEND_COMMAND Panel,"'^BNN-973,192.168.169.99'"
Sets the TakeNote button network name to 192.168.169.99.
^BNT
Syntax:
Set the TakeNote
network port for
the specified
Addresses.
Variable:
"'^BNT-<vt addr range>,<network port>'"
variable text address range = 1 - 4000.
network port = 1 - 65535.
Example:
SEND_COMMAND Panel,"'^BNT-973,5000'"
Sets the TakeNote button network port to 5000.
^BOP
Set the button
opacity.
The button opacity can be specified as a decimal between 0 - 255, where zero (0) is
invisible and 255 is opaque, or as a HEX code, as used in the color commands by
preceding the HEX code with the # sign. In this case, #00 becomes invisible and #FF
becomes opaque. If the opacity is set to zero (0), this does not make the button inactive,
only invisible.
Syntax:
"'^BOP-<vt addr range>,<button states range>,<button
opacity>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
button opacity = 0 (invisible) - 255 (opaque).
Example:
SEND_COMMAND Panel,"'^BOP-500.504&510.515,1,200'"
Example 2:
SEND_COMMAND Panel,"'^BOP-500.504&510.515,1,#C8'"
Both examples set the opacity of the buttons with the variable text range of 500-504 and
510-515 to 200.
7" Modero Widescreen Touch Panels
133
Programming
"^" Button Commands (Cont.)
^BOR
Set a border to a
specific border
style associated
with a border
value for those
buttons with a
defined address
range.
Refer to the Border Styles and Programming Numbers table on page 122 for more
information.
Syntax:
"'^BOR-<vt addr range>,<border style name or border
value>'"
Variable:
variable text address range = 1 - 4000.
border style name = Refer to the Border Styles and Programming Numbers table on
page 122.
border value = 0 - 41.
Examples:
SEND_COMMAND Panel,"'^BOR-500.504&510.515,10'"
Sets the border by number (#10) to those buttons with the variable text range of 500-504
& 510-515.
SEND_COMMAND Panel,"'^BOR-500.504&510,AMX Elite -M'"
Sets the border by name (AMX Elite) to those buttons with the variable text range of
500-504 & 510-515.
The border style is available through the TPDesign4 border-style drop-down list. Refer to
the TPD4 Border Styles by Name table on page 122 for more information.
^BOS
Set the button to
display either a
Video or
Non-Video
window.
Syntax:
"'^BOS-<vt addr range>,<button states range>,<video
state>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
video state = Video Off = 0 and Video On = 1.
Example:
SEND_COMMAND Panel,"'^BOS-500,1,1'"
Sets the button to display video.
^BPP
Zero clears the flag.
Set or clear the
protected page
flip flag of a
button.
Syntax:
"'^BPP-<vt addr range>,<protected page flip flag value>'"
Variable:
variable text address range = 1 - 4000.
protected page flip flag value range = 0 - 4 (0 clears the flag).
Example:
SEND_COMMAND Panel,"'^BPP-500,1'"
Sets the button to protected page flip flag 1 (sets it to password 1).
134
7" Modero Widescreen Touch Panels
Programming
"^" Button Commands (Cont.)
^BRD
Set the border of
a button state/
states.
Only if the specified border is not the same as the current border. The border names are
available through the TPDesign4 border-name drop-down list.
Syntax:
"'^BRD-<vt addr range>,<button states range>,<border
name>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
border name = Refer to Border Styles and Programming Numbers table on page 122.
Example:
SEND_COMMAND Panel,"'^BRD-500.504&510.515,1&2,Quad Line'"
Sets the border by name (Quad Line) to those buttons with the variable text range of
500-504 & 510-515.
Refer to the TPD4 Border Styles by Name table on page 122.
^BSF
Set the focus to
the text area.
Note: Select one button at a time (single variable text address). Do not assign a variable
text address range to set focus to multiple buttons. Only one variable text address can be
in focus at a time.
Syntax:
"'^BSF-<vt addr range>,<selection value>'"
Variable:
variable text address range = 1 - 4000.
selection value = Unselect = 0 and select = 1.
Example:
SEND_COMMAND Panel,"'^BSF-500,1'"
Sets the focus to the text area of the button.
^BSM
This command causes the text areas to send their text as strings to the NetLinx Master.
Submit text for
text area buttons.
Syntax:
"'^BSM-<vt addr range>'"
Variable:
variable text address range = 1 - 4000.
Example:
SEND_COMMAND Panel,"'^BSM-500'"
Submits the text of the text area button.
^BSO
Set the sound
played when a
button is pressed.
If the sound name is blank the sound is then cleared. If the sound name is not matched,
the button sound is not changed.
Syntax:
"'^BSO-<vt addr range>,<button states range>,<sound
name>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
sound name = (blank - sound cleared, not matched - button sound not changed).
Example:
SEND_COMMAND Panel,"'^BSO-500,1&2,music.wav'"
Assigns the sound 'music.wav' to the button Off/On states.
7" Modero Widescreen Touch Panels
135
Programming
"^" Button Commands (Cont.)
^BVL
Syntax:
Log-On/Log-Off
the computer
control
connection.
Variable:
"'^BVL-<vt addr range>,<connection>'"
variable text address range = 1 - 4000.
connection = 0 (Log-Off connection) and 1 (Log-On connection).
Example:
SEND_COMMAND Panel,"'^BVL-500,0'"
Logs-off the computer control connection of the button.
^BVN
Syntax:
Set the network
"'^BVN-<vt addr range>,<network name>'"
name for the
Variable:
specified address.
variable text address range = 1 - 4000.
network name = 1 - 50 ASCII characters.
Example:
SEND_COMMAND Panel,"'^BVN-500,191.191.191.191'"
Sets the network name to ’191.191.191.191’ for the specific control button.
^BVP
Syntax:
Set the network
"'^BVP-<vt addr range>,<network password>'"
password for the
Variable:
specified address.
variable text address range = 1 - 4000.
network password = 1 - 50 ASCII characters.
Example:
SEND_COMMAND Panel,"'^BVP-500,PCLOCK'"
Sets the password to PCLOCK for the specific PC control button.
^BVT
Syntax:
Set the computer
"'^BVT-<vt addr range>,<network port>'"
control network
Variable:
port for the
variable text address range = 1 - 4000.
specified address.
network port = 1 - 65535.
Example:
SEND_COMMAND Panel,"'^BVT-500,5000'"
Sets the network port to 5000.
^BWW
By default, word-wrap is Off.
Set the button
word wrap
feature to those
buttons with a
defined address
range.
Syntax:
"'^BWW-<vt addr range>,<button states range>,<word wrap>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
word wrap = (0=Off and 1=On). Default is Off.
Example:
SEND_COMMAND Panel,"'^BWW-500,1,1'"
Sets the word wrap on for the button’s Off state.
136
7" Modero Widescreen Touch Panels
Programming
"^" Button Commands (Cont.)
^CPF
Syntax:
Clear all page flips
"'^CPF-<vt addr range>'"
from a button.
Variable:
variable text address range = 1 - 4000.
Example:
SEND_COMMAND Panel,"'^CPF-500'"
Clears all page flips from the button.
^DPF
Syntax:
Delete page flips
from button if it
already exists.
Variable:
"'^DFP-<vt addr range>,<actions>,<page name>'"
variable text address range = 1 - 4000.
actions =
Stan[dardPage] - Flip to standard page
Prev[iousPage] - Flip to previous page
Show[Popup] - Show Popup page
Hide[Popup] - Hide Popup page
Togg[lePopup] - Toggle popup state
ClearG[roup] - Clear popup page group from all pages
ClearP[age] - Clear all popup pages from a page with the
specified page name
ClearA[ll] - Clear all popup pages from all pages
page name = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'^DPF-409,Prev'"
Deletes the assignment of a button from flipping to a previous page.
^ENA
Enable or
disable buttons
with a set
variable text
range.
Syntax:
"'^ENA-<vt addr range>,<command value>'"
Variable:
variable text address range = 1 - 4000.
command value = (0= disable, 1= enable)
Example:
SEND_COMMAND Panel,"'^ENA-500.504&510.515,0'"
Disables button pushes on buttons with variable text range 500-504 & 510-515.
^FON
Font ID numbers are generated by the TPDesign4 programmers report.
Set a font to a
specific Font ID
value for those
buttons with a
defined address
range.
Syntax:
"'^FON-<vt addr range>,<button states range>,<font
value>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
font value = Range = 1 - XXX. Refer to the Default Font Styles and ID Numbers table on
page 121.
Example:
SEND_COMMAND Panel,"'^FON-500.504&510.515,1&2,4'"
Sets the font size to font ID #4 for the On and Off states of buttons with the variable text
range of 500-504 & 510-515.
7" Modero Widescreen Touch Panels
137
Programming
The Font ID is generated by TPD4 and is located in TPD4 through the Main menu.
Panel > Generate Programmer's Report >Text Only Format >Readme.txt.
"^" Button Commands (Cont.)
^GDI
Change the
bargraph drag
increment.
Syntax:
"'^GDI-<vt addr range>,<bargraph drag increment>'"
Variable:
variable text address range = 1 - 4000.
bargraph drag increment = The default drag increment is 256.
Example:
SEND_COMMAND Panel,"'^GDI-7,128'"
Sets the bargraph with variable text 7 to a drag increment of 128.
^GIV
Invert the
joystick axis to
move the origin to
another corner.
Parameters 1,2, and 3 will cause a bargraph or slider to be inverted regardless of
orientation. Their effect will be as described for joysticks.
Syntax:
"'^GIV-<vt addr range>,<joystick axis to invert>'"
Variable:
variable text address range = 1 - 4000.
joystick axis to invert = 0 - 3.
0
1
2
3
0 = Normal
1 = Invert horizontal axis
2 = Invert vertical axis
3 = Invert both axis locations
For a bargraph 1 = Invert , 0 = Non Invert
Example:
SEND_COMMAND Panel,"'^GIV-500,3'"
Inverts the joystick axis origin to the bottom right corner.
^GLH
Change the
bargraph upper
limit.
Syntax:
"'^GLH-<vt addr range>,<bargraph hi>'"
Variable:
variable text address range = 1 - 4000.
bargraph limit range = 1 - 65535 (bargraph upper limit range).
Example:
SEND_COMMAND Panel,"'^GLH-500,1000'"
Changes the bargraph upper limit to 1000.
^GLL
Change the
bargraph lower
limit.
Syntax:
"'^GLL-<vt addr range>,<bargraph low>'"
Variable:
variable text address range = 1 - 4000.
bargraph limit range = 1 - 65535 (bargraph lower limit range).
Example:
SEND_COMMAND Panel,"'^GLL-500,150'"
Changes the bargraph lower limit to 150.
138
7" Modero Widescreen Touch Panels
Programming
"^" Button Commands (Cont.)
^GRD
Syntax:
Change the
"'^GRD-<vt addr range>,<bargraph ramp down time>'"
bargraph
Variable:
ramp-down time in
variable text address range = 1 - 4000.
1/10th of a
second.
bargraph ramp down time = In 1/10th of a second intervals.
Example:
SEND_COMMAND Panel,"'^GRD-500,200'"
Changes the bargraph ramp down time to 20 seconds.
^GRU
Change the
bargraph
ramp-up time in
1/10th of a
second.
Syntax:
"'^GRU-<vt addr range>,<bargraph ramp up time>'"
Variable:
variable text address range = 1 - 4000.
bargraph ramp up time = In 1/10th of a second intervals.
Example:
SEND_COMMAND Panel,"'^GRU-500,100'"
Changes the bargraph ramp up time to 10 seconds.
^GSC
A user can also assign the color by Name and R,G,B value (RRGGBB or RRGGBBAA).
Change the
bargraph slider
color or joystick
cursor color.
Syntax:
"'^GSC-<vt addr range>,<color value>'"
Variable:
variable text address range = 1 - 4000.
color value = Refer to the RGB Values for all 88 Basic Colors table on page 119.
Example:
SEND_COMMAND Panel,"'^GSC-500,12'"
Changes the bargraph or joystick slider color to Yellow.
^GSN
Change the
bargraph slider
name or joystick
cursor name.
Slider names and cursor names can be found in the TPDesign4 slider name and cursor
drop-down list.
Syntax:
"'^GSN-<vt addr range>,<bargraph slider name>'"
Variable:
variable text address range = 1 - 4000.
bargraph slider name = See table below.
Bargraph Slider Names:
None
Ball
Circle -L
Circle -M
Circle -S
Precision
Rectangle -L
Rectangle -M
Rectangle -S
Windows
Windows Active
Joystick Cursor Names:
None
Arrow
Ball
Circle
Crosshairs
Gunsight
Hand
Metal
Spiral
Target
View Finder
Example:
SEND_COMMAND Panel,"'^GSN-500,Ball'"
Changes the bargraph slider name or the Joystick cursor name to ’Ball’.
7" Modero Widescreen Touch Panels
139
Programming
"^" Button Commands (Cont.)
^ICO
Set the icon to a
button.
Syntax:
"'^ICO-<vt addr range>,<button states range>,<icon
index>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
icon index range = 0 - 9900 (a value of 0 is clear).
Example:
SEND_COMMAND Panel,"'^ICO-500.504&510.515,1&2,1'"
Sets the icon for On and Off states for buttons with variable text ranges of 500-504 &
510-515.
^JSB
The alignment of 0 is followed by ',<left>,<top>'. The left and top coordinates are relative
to the upper left corner of the button.
Set bitmap/
picture alignment Syntax:
using a numeric
"'^JSB-<vt addr range>,<button states range>,<new text
keypad layout for
alignment>'"
those buttons with
a defined address Variable:
range.
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
new text alignment = Value of 1 - 9 corresponds to the following locations:
0
1
2
3
4
5
6
7
8
9
Zero can be used for an absolute position
Example:
SEND_COMMAND Panel,"'^JSB-500.504&510.515,1&2,1'"
Sets the off/on state picture alignment to upper left corner for those buttons with variable
text ranges of 500-504 & 510-515.
^JSI
Set icon
alignment using a
numeric keypad
layout for those
buttons with a
defined address
range.
The alignment of 0 is followed by ',<left>,<top>'. The left and top coordinates are relative
to the upper left corner of the button.
Syntax:
"'^JSI-<vt addr range>,<button states range>,<new icon
alignment>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
new icon alignment = Value of 1 - 9 corresponds to the following locations:
0
1
2
3
4
5
6
7
8
9
Zero can be used for an absolute position
Example:
SEND_COMMAND Panel,"'^JSI-500.504&510.515,1&2,1'"
Sets the Off/On state icon alignment to upper left corner for those buttons with variable
text range of 500-504 & 510-515.
140
7" Modero Widescreen Touch Panels
Programming
"^" Button Commands (Cont.)
The alignment of 0 is followed by ',<left>,<top>'. The left and top coordinates are relative
to the upper left corner of the button.
Set text
alignment using a Syntax:
numeric keypad
"'^JST-<vt addr range>,<button states range>,<new text
layout for those
alignment>'"
buttons with a
Variable:
defined address
range.
variable text address range = 1 - 4000.
^JST
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
new text alignment = Value of 1 - 9 corresponds to the following locations:
0
1
2
3
4
5
6
7
8
9
Zero can be used for an absolute position
Example:
SEND_COMMAND Panel,"'^JST-500.504&510.515,1&2,1'"
Sets the text alignment to the upper left corner for those buttons with variable text ranges
of 500-504 & 510-515.
^MBT
Set the Mouse
Button mode On
for the virtual PC.
Syntax:
"'^MBT-<pass data>'"
Variable:
pass data:
0 = None
1 = Left
2 = Right
3 = Middle
Example:
SEND COMMAND Panel,"'^MBT-1'"
Sets the mouse button mode to ’Left Mouse Click’.
^MDC
Turn On the
’Mouse
double-click’
feature for the
virtual PC.
^SHO
Show or hide a
button with a set
variable text
range.
Syntax:
"'^MDC'"
Example:
SEND COMMAND Panel,"'^MDC'"
Sets the mouse double-click for use with the virtual PC.
Syntax:
"'^SHO-<vt addr range>,<command value>'"
Variable:
variable text address range = 1 - 4000.
command value = (0= hide, 1= show).
Example:
SEND_COMMAND Panel,"'^SHO-500.504&510.515,0'"
Hides buttons with variable text address range 500-504 & 510-515.
7" Modero Widescreen Touch Panels
141
Programming
"^" Button Commands (Cont.)
^TEC
Set the text effect
color for the
specified
addresses/states
to the specified
color.
The Text Effect is specified by name and can be found in TPD4. You can also assign the
color by name or RGB value (RRGGBB or RRGGBBAA).
Syntax:
"'^TEC-<vt addr range>,<button states range>,<color
value>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
color value = Refer to the RGB Values for all 88 Basic Colors table on page 119.
Example:
SEND_COMMAND Panel,"'^TEC-500.504&510.515,1&2,12'"
Sets the text effect color to Very Light Yellow on buttons with variable text 500-504
and 510-515.
^TEF
The Text Effect is specified by name and can be found in TPD4.
Set the text effect. Syntax:
"'^TEF-<vt addr range>,<button states range>,<text effect
name>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
text effect name = Refer to the Text Effects table on page 144 for a listing of text
effect names.
Example:
SEND_COMMAND Panel,"'^TEF-500.504&510.515,1&2,Soft Drop
Shadow 3'"
Sets the text effect to Soft Drop Shadow 3 for the button with variable text range 500-504
and 510-515.
^TXT
Sets Non-Unicode text.
Assign a text
string to those
buttons with a
defined address
range.
Syntax:
"'^TXT-<vt addr range>,<button states range>,<new text>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
new text = 1 - 50 ASCII characters.
Example:
SEND_COMMAND Panel,"'^TXT-500.504&510.515,1&2,Test Only'"
Sets the On and Off state text for buttons with the variable text ranges of
500-504 & 510-515.
142
7" Modero Widescreen Touch Panels
Programming
"^" Button Commands (Cont.)
^UNI
Set Unicode text.
For the ^UNI command (%UN and ^BMF command), the Unicode text is sent as
ASCII-HEX nibbles.
Syntax:
"'^UNI-<vt addr range>,<button states range>,<unicode
text>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
unicode text = Unicode HEX value.
Example:
SEND_COMMAND Panel,"'^UNI-500,1,0041'"
Sets the button’s unicode character to ’A’.
Note: To send the variable text ’A’ in unicode to all states of the variable text
button 1, (for which the character code is 0041 Hex), send the following command:
SEND_COMMAND TP,"'^UNI-1,0,0041'"
Note: Unicode is always represented in a HEX value. TPD4 generates (through the
Text Enter Box dialog) unicode HEX values. Refer to the TPDesign4 Instruction
Manual for more information.
7" Modero Widescreen Touch Panels
143
Programming
Text Effect Names
The following is a listing of text effects names. This list is associated with the ^TEF command on
page 142.
Text Effects
• Glow -S
• Hard Drop Shadow 6
• Glow -M
• Hard Drop Shadow 7
• Glow -L
• Hard Drop Shadow 8
• Glow -X
• Soft Drop Shadow 1 with outline
• Outline -S
• Soft Drop Shadow 2 with outline
• Outline -M
• Soft Drop Shadow 3 with outline
• Outline -L
• Soft Drop Shadow 4 with outline
• Outline -X
• Soft Drop Shadow 5 with outline
• Soft Drop Shadow 1
• Soft Drop Shadow 6 with outline
• Soft Drop Shadow 2
• Soft Drop Shadow 7 with outline
• Soft Drop Shadow 3
• Soft Drop Shadow 8 with outline
• Soft Drop Shadow 4
• Medium Drop Shadow 1 with outline
• Soft Drop Shadow 5
• Medium Drop Shadow 2 with outline
• Soft Drop Shadow 6
• Medium Drop Shadow 3 with outline
• Soft Drop Shadow 7
• Medium Drop Shadow 4 with outline
• Soft Drop Shadow 8
• Medium Drop Shadow 5 with outline
• Medium Drop Shadow 1
• Medium Drop Shadow 6 with outline
• Medium Drop Shadow 2
• Medium Drop Shadow 7 with outline
• Medium Drop Shadow 3
• Medium Drop Shadow 8 with outline
• Medium Drop Shadow 4
• Hard Drop Shadow 1 with outline
• Medium Drop Shadow 5
• Hard Drop Shadow 2 with outline
• Medium Drop Shadow 6
• Hard Drop Shadow 3 with outline
• Medium Drop Shadow 7
• Hard Drop Shadow 4 with outline
• Medium Drop Shadow 8
• Hard Drop Shadow 5 with outline
• Hard Drop Shadow 1
• Hard Drop Shadow 6 with outline
• Hard Drop Shadow 2
• Hard Drop Shadow 7 with outline
• Hard Drop Shadow 3
• Hard Drop Shadow 8 with outline
• Hard Drop Shadow 4
• Hard Drop Shadow 5
144
7" Modero Widescreen Touch Panels
Programming
Button Query Commands
Button Query commands reply back with a custom event. There will be one custom event for each
button/state combination. Each query is assigned a unique custom event type. The following
example is for debug purposes only:
NetLinx Example: CUSTOM_EVENT[device, Address, Custom event type]
DEFINE_EVENT
CUSTOM_EVENT[TP,529,1001]
// Text
CUSTOM_EVENT[TP,529,1002]
// Bitmap
CUSTOM_EVENT[TP,529,1003]
// Icon
CUSTOM_EVENT[TP,529,1004]
// Text Justification
CUSTOM_EVENT[TP,529,1005]
// Bitmap Justification
CUSTOM_EVENT[TP,529,1006]
// Icon Justification
CUSTOM_EVENT[TP,529,1007]
// Font
CUSTOM_EVENT[TP,529,1008]
// Text Effect Name
CUSTOM_EVENT[TP,529,1009]
// Text Effect Color
CUSTOM_EVENT[TP,529,1010]
// Word Wrap
CUSTOM_EVENT[TP,529,1011]
// ON state Border Color
CUSTOM_EVENT[TP,529,1012]
// ON state Fill Color
CUSTOM_EVENT[TP,529,1013]
// ON state Text Color
CUSTOM_EVENT[TP,529,1014]
// Border Name
CUSTOM_EVENT[TP,529,1015]
// Opacity
{
Send_String 0,"'ButtonGet Id=',ITOA(CUSTOM.ID),'
Type=',ITOA(CUSTOM.TYPE)"
Send_String 0,"'Flag
=',ITOA(CUSTOM.FLAG)"
Send_String 0,"'VALUE1 =',ITOA(CUSTOM.VALUE1)"
Send_String 0,"'VALUE2 =',ITOA(CUSTOM.VALUE2)"
Send_String 0,"'VALUE3 =',ITOA(CUSTOM.VALUE3)"
Send_String 0,"'TEXT
=',CUSTOM.TEXT"
Send_String 0,"'TEXT LENGTH =',ITOA(LENGTH_STRING(CUSTOM.TEXT))"
}
7" Modero Widescreen Touch Panels
145
Programming
All custom events have the following 6 fields:
Custom Event Fields
Field
Description
Uint Flag
0 means text is a standard string, 1 means Unicode encoded string
slong value1
button state number
slong value2
actual length of string (this is not encoded size)
slong value3
index of first character (usually 1 or same as optional index
string text
the text from the button
text length (string encode)
button text length
These fields are populated differently for each query command. The text length (String Encode)
field is not used in any command.
Button Query Commands
?BCB
Get the current
border color.
Syntax:
"'?BCB-<vt addr range>,<button states range>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1011:
Flag - zero
Value1 - Button state number
Value2 - Actual length of string (should be 9)
Value3 - Zero
Text - Hex encoded color value (ex: #000000FF)
Text length - Color name length (should be 9)
Example:
SEND COMMAND Panel,"'?BCB-529,1'"
Gets the button 'OFF state' border color. information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1011
Flag = 0
VALUE1 = 1
VALUE2 = 9
VALUE3 = 0
TEXT = #222222FF
TEXT LENGTH = 9
146
7" Modero Widescreen Touch Panels
Programming
Button Query Commands (Cont.)
?BCF
Syntax:
Get the current fill
color.
Variable:
"'?BCF-<vt addr range>,<button states range>'"
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1012:
Flag - Zero
Value1 - Button state number
Value2 - Actual length of string (should be 9)
Value3 - Zero
Text - Hex encoded color value (ex: #000000FF)
Text length - Color name length (should be 9)
Example:
SEND COMMAND Panel,"'?BCF-529,1'"
Gets the button 'OFF state' fill color information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1012
Flag = 0
VALUE1 = 1
VALUE2 = 9
VALUE3 = 0
TEXT = #FF8000FF
TEXT LENGTH = 9
?BCT
Get the current
text color.
Syntax:
"'?BCT-<vt addr range>,<button states range>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1013:
Flag - Zero
Value1 - Button state number
Value2 - Actual length of string (should be 9)
Value3 - Zero
Text - Hex encoded color value (ex: #000000FF)
Text length - Color name length (should be 9)
Example:
SEND COMMAND Panel,"'?BCT-529,1'"
Gets the button 'OFF state' text color information.
The result sent to Master would be:
ButtonGet Id = 529 Type = 1013
Flag = 0
VALUE1 = 1
VALUE2 = 9
VALUE3 = 0
TEXT = #FFFFFEFF
TEXT LENGTH = 9
7" Modero Widescreen Touch Panels
147
Programming
Button Query Commands (Cont.)
?BMP
Syntax:
Get the current
bitmap name.
Variable:
"'?BMP-<vt addr range>,<button states range>'"
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1002:
Flag - Zero
Value1 - Button state number
Value2 - Actual length of string
Value3 - Zero
Text - String that represents the bitmap name
Text length - Bitmap name text length (should be 9)
Example:
SEND COMMAND Panel,"'?BMP-529,1'"
Gets the button 'OFF state' bitmap information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1002
Flag = 0
VALUE1 = 1
VALUE2 = 9
VALUE3 = 0
TEXT = Buggs.png
TEXT LENGTH = 9
?BOP
Get the overall
button opacity.
Syntax:
"'?BOP-<vt addr range>,<button states range>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1015:
Flag - Zero
Value1 - Button state number
Value2 - Opacity
Value3 - Zero
Text - Blank
Text length - Zero
Example:
SEND COMMAND Panel,"'?BOP-529,1'"
Gets the button 'OFF state' opacity information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1015
Flag = 0
VALUE1 = 1
VALUE2 = 200
VALUE3 = 0
TEXT =
TEXT LENGTH = 0
148
7" Modero Widescreen Touch Panels
Programming
Button Query Commands (Cont.)
?BRD
Syntax:
Get the current
border name.
Variable:
"'?BRD-<vt addr range>,<button states range>'"
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1014:
Flag - Zero
Value1 - Button state number
Value2 - Actual length of string
Value3 - Zero
Text - String that represents border name
Text length - Border name length
Example:
SEND COMMAND Panel,"'?BRD-529,1'"
Gets the button 'OFF state' border information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1014
Flag = 0
VALUE1 = 1
VALUE2 = 22
VALUE3 = 0
TEXT = Double Bevel Raised -L
TEXT LENGTH = 22
?BWW
Get the current
word wrap flag
status.
Syntax:
"'?BWW-<vt addr range>,<button states range>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1010:
Flag - Zero
Value1 - Button state number
Value2 - 0 = no word wrap, 1 = word wrap
Value3 - Zero
Text - Blank
Text length - Zero
Example:
SEND COMMAND Panel,"'?BWW-529,1'"
Gets the button 'OFF state' word wrap flag status information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1010
Flag = 0
VALUE1 = 1
VALUE2 = 1
VALUE3 = 0
TEXT =
TEXT LENGTH = 0
7" Modero Widescreen Touch Panels
149
Programming
Button Query Commands (Cont.)
?FON
Syntax:
Get the current
font index.
Variable:
"'?FON-<vt addr range>,<button states range>'"
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1007:
Flag - Zero
Value1 - Button state number
Value2 - Font index
Value3 - Zero
Text - Blank
Text length - Zero
Example:
SEND COMMAND Panel,"'?FON-529,1'"
Gets the button 'OFF state' font type index information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1007
Flag = 0
VALUE1 = 1
VALUE2 = 72
VALUE3 = 0
TEXT =
TEXT LENGTH = 0
?ICO
Get the current
icon index.
Syntax:
"'?ICO-<vt addr range>,<button states range>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1003:
Flag - Zero
Value1 - Button state number
Value2 - Icon Index
Value3 - Zero
Text - Blank
Text length - Zero
Example:
SEND COMMAND Panel,"'?ICO-529,1&2'"
Gets the button 'OFF state' icon index information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1003
Flag = 0
VALUE1 = 2
VALUE2 = 12
VALUE3 = 0
TEXT =
TEXT LENGTH = 0
150
7" Modero Widescreen Touch Panels
Programming
Button Query Commands (Cont.)
?JSB
Syntax:
Get the current
bitmap
justification.
Variable:
"'?JSB-<vt addr range>,<button states range>'"
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1005:
Flag - Zero
Value1 - Button state number
Value2 - 1 - 9 justify
Value3 - Zero
Text - Blank
Text length - Zero
Example:
SEND COMMAND Panel,"'?JSB-529,1'"
Gets the button 'OFF state' bitmap justification information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1005
Flag = 0
VALUE1 = 1
VALUE2 = 5
VALUE3 = 0
TEXT =
TEXT LENGTH = 0
?JSI
Get the current
icon
justification.
Syntax:
"'?JSI-<vt addr range>,<button states range>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1006:
Flag - Zero
Value1 - Button state number
Value2 - 1 - 9 justify
Value3 - Zero
Text - Blank
Text length - Zero
Example:
SEND COMMAND Panel,"'?JSI-529,1'"
Gets the button 'OFF state' icon justification information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1006
Flag = 0
VALUE1 = 1
VALUE2 = 6
VALUE3 = 0
TEXT =
TEXT LENGTH = 0
7" Modero Widescreen Touch Panels
151
Programming
Button Query Commands (Cont.)
?JST
Syntax:
Get the current
text
justification.
Variable:
"'?JST-<vt addr range>,<button states range>'"
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1004:
Flag - Zero
Value1 - Button state number
Value2 - 1 - 9 justify
Value3 - Zero
Text - Blank
Text length - Zero
Example:
SEND COMMAND Panel,"'?JST-529,1'"
Gets the button 'OFF state' text justification information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1004
Flag = 0
VALUE1 = 1
VALUE2 = 1
VALUE3 = 0
TEXT =
TEXT LENGTH = 0
?TEC
Get the current
text effect color.
Syntax:
"'?TEC-<vt addr range>,<button states range>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1009:
Flag - Zero
Value1 - Button state number
Value2 - Actual length of string (should be 9)
Value3 - Zero
Text - Hex encoded color value (ex: #000000FF)
Text length - Color name length (should be 9)
Example:
SEND COMMAND Panel,"'?TEC-529,1'"
Gets the button 'OFF state' text effect color information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1009
Flag = 0
VALUE1 = 1
VALUE2 = 9
VALUE3 = 0
TEXT = #5088F2AE
TEXT LENGTH = 9
152
7" Modero Widescreen Touch Panels
Programming
Button Query Commands (Cont.)
?TEF
Syntax:
Get the current
text effect name.
Variable:
"'?TEF-<vt addr range>,<button states range>'"
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
custom event type 1008:
Flag - Zero
Value1 - Button state number
Value2 - Actual length of string
Value3 - Zero
Text - String that represents the text effect name
Text length - Text effect name length
Example:
SEND COMMAND Panel,"'?TEF-529,1'"
Gets the button 'OFF state' text effect name information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1008
Flag = 0
VALUE1 = 1
VALUE2 = 18
VALUE3 = 0
TEXT = Hard Drop Shadow 3
TEXT LENGTH = 18
?TXT
Get the current
text information.
Syntax:
"'?TXT-<vt addr range>,<button states range>,<optional
index>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
optional index = This is used if a string was too long to get back in one command.
The reply will start at this index.
custom event type 1001:
Flag - Zero
Value1 - Button state number
Value2 - Actual length of string
Value3 - Index
Text - Text from the button
Text length - Button text length
Example:
SEND COMMAND Panel,"'?TXT-529,1'"
Gets the button 'OFF state' text information.
The result sent to the Master would be:
ButtonGet Id = 529 Type = 1001
Flag = 0
VALUE1 = 1
VALUE2 = 14
VALUE3 = 1
TEXT = This is a test
TEXT LENGTH = 14
7" Modero Widescreen Touch Panels
153
Programming
Panel Runtime Operations
Serial Commands are used in the AxcessX Terminal Emulator mode. These commands are case
insensitive.
Panel Runtime Operation Commands
ABEEP
Output a single
beep even if beep
is Off.
Syntax:
"'ABEEP'"
Example:
SEND COMMAND Panel,"'ABEEP'"
Outputs a beep of duration 1 beep even if beep is Off.
ADBEEP
Syntax:
Output a double
beep even if beep
is Off.
Example:
"'ADBEEP'"
SEND COMMAND Panel,"'ADBEEP'"
Outputs a double beep even if beep is Off.
Keyboard string is set to null on power up and is stored until power is lost. The Prompt Text
is optional.
Pop up the
keyboard icon and Syntax:
initialize the text
"'@AKB-<initial text>;<prompt text>'"
string to that
Variables:
specified.
initial text = 1 - 50 ASCII characters.
@AKB
prompt text = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'@AKB-Texas;Enter State'"
Pops up the Keyboard and initializes the text string 'Texas' with prompt text 'Enter State'.
AKEYB
Keyboard string is set to null on power up and is stored until power is lost.
Syntax:
Pop up the
keyboard icon and
"'AKEYB-<initial text>'"
initialize the text
Variables:
string to that
specified.
initial text = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'AKEYB-This is a Test'"
Pops up the Keyboard and initializes the text string 'This is a Test'.
AKEYP
The keypad string is set to null on power up and is stored until power is lost.
Pop up the
keypad icon and
initialize the text
string to that
specified.
Syntax:
"'AKEYP-<number string>'"
Variables:
number string = 0 - 9999.
Example:
SEND COMMAND Panel,"'AKEP-12345'"
Pops up the Keypad and initializes the text string '12345'.
AKEYR
Remove the
Keyboard/
Keypad.
Remove keyboard or keypad that was displayed using 'AKEYB', 'AKEYP', 'PKEYP',
@AKB, @AKP, @PKP, @EKP, or @TKP commands.
Syntax:
"'AKEYR'"
Example:
SEND COMMAND Panel,"'AKEYR'"
Removes the Keyboard/Keypad.
154
7" Modero Widescreen Touch Panels
Programming
Panel Runtime Operation Commands (Cont.)
@AKP
Pop up the
keypad icon and
initialize the text
string to that
specified.
Keypad string is set to null on power up and is stored until power is lost. The Prompt Text
is optional.
Syntax:
"'@AKP-<initial text>;<prompt text>'"
Variables:
initial text = 1 - 50 ASCII characters.
prompt text = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'@AKP-12345678;ENTER PASSWORD'"
Pops up the Keypad and initializes the text string '12345678' with prompt text ’ENTER
PASSWORD’.
@AKR
Remove the
Keyboard/
Keypad.
Remove keyboard or keypad that was displayed using 'AKEYB', 'AKEYP', 'PKEYP',
@AKB, @AKP, @PKP, @EKP, or @TKP commands.
Syntax:
"'@AKR'"
Example:
SEND COMMAND Panel,"'@AKR'"
Removes the Keyboard/Keypad.
BEEP
Output a beep.
Syntax:
"'BEEP'"
Example:
SEND COMMAND Panel,"'BEEP'"
Outputs a beep.
BRIT
Set the panel
brightness.
Syntax:
"'BRIT-<brightness level>'"
Variable:
brightness level = 0 - 100.
Example:
SEND COMMAND Panel,"'BRIT-50'"
Sets the brightness level to 50.
@BRT
Set the panel
brightness.
Syntax:
"'@BRT-<brightness level>'"
Variable:
brightness level = 0 - 100.
Example:
SEND COMMAND Panel,"'@BRT-70'"
Sets the brightness level to 70.
DBEEP
Output a
double beep.
Syntax:
"'DBEEP'"
Example:
SEND COMMAND Panel,"'DBEEP'"
Outputs a double beep.
7" Modero Widescreen Touch Panels
155
Programming
Panel Runtime Operation Commands (Cont.)
@EKP
Extend the
Keypad.
Pops up the keypad icon and initializes the text string to that specified. The Prompt Text is
optional.
Syntax:
"'@EKP-<initial text>;<prompt text>'"
Variables:
initial text = 1 - 50 ASCII characters.
prompt text = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'@EKP-33333333;Enter Password'"
Pops up the Keypad and initializes the text string '33333333' with prompt text 'Enter
Password'.
PKEYP
Present a private
keypad.
Pops up the keypad icon and initializes the text string to that specified. Keypad displays a
'*' instead of the numbers typed. The Prompt Text is optional.
Syntax:
"'PKEYP-<initial text>'"
Variables:
initial text = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'PKEYP-123456789'"
Pops up the Keypad and initializes the text string '123456789' in '*'.
@PKP
Present a private
keypad.
Pops up the keypad icon and initializes the text string to that specified. Keypad displays a
'*' instead of the numbers typed. The Prompt Text is optional.
Syntax:
"'@PKP-<initial text>;<prompt text>'"
Variables:
initial text = 1 - 50 ASCII characters.
prompt text = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'@PKP-1234567;ENTER PASSWORD'"
Pops up the Keypad and initializes the text string 'ENTER PASSWORD' in '*'.
SETUP
Send panel to
SETUP page.
Syntax:
"'SETUP'"
Example:
SEND COMMAND Panel,"'SETUP'"
Sends the panel to the Setup Page.
SHUTDOWN
Syntax:
Shut down the
"'SHUTDOWN'"
batteries providing Example:
power to the
SEND COMMAND Panel,"'SHUTDOWN'"
panel.
Shuts-down the batteries feeding power to the panel. This function saves the battery from
discharging.
SLEEP
Force the panel
into screen saver
mode.
Syntax:
"'SLEEP'"
Example:
SEND COMMAND Panel,"'SLEEP'"
Forces the panel into screen saver mode.
156
7" Modero Widescreen Touch Panels
Programming
Panel Runtime Operation Commands (Cont.)
@SOU
Play a sound file.
Syntax:
"'@SOU-<sound name>'"
Variables:
sound name = Name of the sound file. Supported sound file formats are: WAV & MP3.
Example:
SEND COMMAND Panel,"'@SOU-Music.wav'"
Plays the 'Music.wav' file.
@TKP
Present a
telephone
keypad.
Pops up the keypad icon and initializes the text string to that specified. The Prompt Text is
optional.
Syntax:
"'@TKP-<initial text>;<prompt text>'"
Variables:
initial text = 1 - 50 ASCII characters.
prompt text = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'@TKP-999.222.1211;Enter Phone
Number'"
Pops-up the Keypad and initializes the text string '999.222.1211' with prompt text 'Enter
Phone Number'.
TPAGEON
Turn On page
tracking.
This command turns On page tracking, whereby when the page or popups change, a
string is sent to the Master. This string may be captured with a CREATE_BUFFER
command for one panel and sent directly to another panel.
Syntax:
"'TPAGEON'"
Example:
SEND COMMAND Panel,"'TPAGEON'"
Turns On page tracking.
TPAGEOFF
Turn Off page
tracking.
Syntax:
"'TPAGEOFF'"
Example:
SEND COMMAND Panel,"'TPAGEOFF'"
Turns Off page tracking.
@VKB
Popup the
virtual
keyboard.
Syntax:
"'@VKB'"
Example:
SEND COMMAND Panel,"'@VKB'"
Pops-up the virtual keyboard.
WAKE
Force the panel
out of screen
saver mode.
Syntax:
"'WAKE'"
Example:
SEND COMMAND Panel,"'WAKE'"
Forces the panel out of the screen saver mode.
7" Modero Widescreen Touch Panels
157
Programming
Input Commands
These Send Commands are case insensitive.
Input Commands
^CAL
Syntax:
Put panel in
calibration mode.
Example:
"'^CAL'"
SEND COMMAND Panel,"'^CAL'"
Puts the panel in calibration mode.
^KPS
Set the
keyboard
passthru.
Syntax:
"'^KPS-<pass data>'"
Variable:
pass data:
<blank/empty> = Disables the keyboard.
0 = Pass data to G4 application (default). This can be used with VPC or text areas.
1 - 4 = Not used.
5 = Sends out data to the Master.
Example:
SEND COMMAND Panel,"'^KPS-5'"
Sets the keyboard passthru to the Master. Option 5 sends keystrokes directly to the
Master via the Send Output String mechanism. This process sends a virtual keystroke
command (^VKS) to the Master.
Example 2:
SEND COMMAND Panel,"'^KPS-0'"
Disables the keyboard passthru to the Master.
The following point defines how the parameters within this command work:
• Accepts keystrokes from any of these sources: attached USB keyboard or Virtual
keyboard.
^VKS
Send one or more
virtual key strokes
to the G4
application.
Key presses and key releases are not distinguished except in the case of CTRL, ALT, and
SHIFT.
Refer to the Embedded Codes table on page 159 that define special characters which
can be included with the string but may not be represented by the ASCII character set.
Syntax:
"'^VKS-<string>'"
Variable:
string = Only 1 string per command/only one stroke per command.
Example:
SEND COMMAND Panel,"'^VKS-'8"
Sends out the keystroke 'backspace' to the G4 application.
158
7" Modero Widescreen Touch Panels
Programming
Embedded codes
The following is a list of G4 compatible embedded codes:
Embedded Codes
Decimal numbers
Hexidecimal values
Virtual keystroke
8
($08)
Backspace
13
($0D)
Enter
27
($1B)
ESC
128
($80)
CTRL key down
129
($81)
ALT key down
130
($82)
Shift key down
131
($83)
F1
132
($84)
F2
133
($85)
F3
134
($86)
F4
135
($87)
F5
136
($88)
F6
137
($89)
F7
138
($8A)
F8
139
($8B)
F9
140
($8C)
F10
141
($8D)
F11
142
($8E)
F12
143
($8F)
Num Lock
144
($90)
Caps Lock
145
($91)
Insert
146
($92)
Delete
147
($93)
Home
148
($94)
End
149
($95)
Page Up
150
($96)
Page Down
151
($97)
Scroll Lock
152
($98)
Pause
153
($99)
Break
154
($9A)
Print Screen
155
($9B)
SYSRQ
156
($9C)
Tab
157
($9D)
Windows
158
($9E)
Menu
159
($9F)
Up Arrow
160
($A0)
Down Arrow
161
($A1)
Left Arrow
162
($A2)
Right Arrow
192
($C0)
CTRL key up
193
($C1)
ALT key up
194
($C2)
Shift key up
7" Modero Widescreen Touch Panels
159
Programming
Panel Setup Commands
These commands are case insensitive.
Panel Setup Commands
^MUT
Syntax:
Set the panel
mute state.
Variable:
"'^MUT-<mute state>'"
mute state= 0 = Mute Off and 1 = Mute On.
Example:
SEND_COMMAND Panel,"'^MUT-1''"
Sets the panel’s master volume to mute.
@PWD
@PWD sets the level 1 password only.
Set the page flip
password.
Syntax:
"'@PWD-<page flip password>'"
Variables:
page flip password = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'@PWD-Main'"
Sets the page flip password to 'Main'.
^PWD
Password level is required and must be 1 - 4.
Set the page flip
password.
Syntax:
"'^PWD-<password level>,<page flip password>'"
Variables:
password level = 1 - 4.
page flip password = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'^PWD-1,Main'"
Sets the page flip password on Password Level 1 to 'Main'.
^VOL
Set the panel
volume.
Syntax:
"'^VOL-<volume level>'"
Variable:
volume level = 0 - 100. 100 is maximum volume setting.
Example:
SEND_COMMAND Panel,"'^VOL-50'"
Set the panel volume to 50.
160
7" Modero Widescreen Touch Panels
Programming
Dynamic Image Commands
The following is a listing and descriptions of Dynamic Image Commands.
Dynamic Image Commands
^BBR
Set the bitmap of
a button to use a
particular
resource.
Syntax:
"'^BBR-<vt addr range>,<button states range>,<resource
name>'"
Variable:
variable text address range = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
resource name = 1 - 50 ASCII characters.
Example:
SEND_COMMAND Panel,"'^BBR-700,1,Sports_Image'"
Sets the resource name of the button to ’Sports_Image’.
^RAF
See page 162.
^RFR
Syntax:
Force a refresh for
a given resource.
"'^RFR-<resource name>'"
Variable:
resource name = 1 - 50 ASCII characters.
Example:
SEND_COMMAND Panel,"'^RFR-Sports_Image'"
Forces a refresh on ’Sports_Image’.
^RMF
Modify an
existing resource.
Syntax:
"'^RMF-<resource name>,<data>'"
Variable:
resource name = 1 - 50 ASCII characters
data = Refer to the table in the RAF command for more information.
Example:
SEND_COMMAND Panel,"'^RMF-Sports_Image%ALab_Test/
Images%Ftest.jpg'"
Changes the resource ’Sports_Image’ file name to ’test.jpg’ and the path to ’Lab_Test/
Images’.
^RSR
Change the
refresh rate for a
given resource.
Syntax:
"'^RSR-<resource name>,<refresh rate>'"
Variable:
resource name = 1 - 50 ASCII characters.
refresh rate = Measured in seconds.
Example:
SEND_COMMAND Panel,"'^RSR-Sports_Image,5'"
Sets the refresh rate to 5 seconds for the given resource (’Sports_Image’).
7" Modero Widescreen Touch Panels
161
Programming
Dynamic Image Commands (Cont.)
^RAF
Adds any and all resource parameters by sending embedded codes and data.
Add new
resources.
Syntax:
"'^RAF-<resource name>,<data>'"
Variable:
resource name = 1 - 50 ASCII characters.
data = Refers to the embedded codes, see table below.
Embedded Codes:
Parameter
Embedded Code
Description
protocol
’%P<0-1>’
Set protocol. HTTP (0) or FTP (1).
user
’%U<user>’
Set Username for authentication.
password
’%S<password>’
Set Password for authentication.
host
’%H<host>’
Set Host Name (fully qualified
DNS or IP Address).
file
’%F<file>’
Full path to the location of the file or
program that will return the resource.
The path must be a valid HTTP URL
minus the protocol and host. The
only exception to this is the inclusion
of special escape sequences and in
the case of the FTP protocol, regular
expressions.
path
’%A<path>’
Set Directory path. The path must
be a valid HTTP URL minus the
protocol, host, and filename. The
only exception to this is the
inclusion of special escape
sequences and in the case of the
FTP protocol, regular expressions.
refresh
’%R<refresh 1-65535>’
newest
’%N<0-1>’
The number of seconds between
refreshes in which the resource is
downloaded again. Refreshing a
resource causes the button
displaying that resource to refresh
also. The default value is 0 (only
download the resource once).
Set the newest file. A value of 1
means that only the most recent file
matching the pattern is downloaded.
preserve
’%V<0-1>’
Set the value of the preserve flag.
Default is 0. Currently preserve has
no function.
Example:
SEND_COMMAND Panel,"'^RAF-New Image,%P0%HAMX.COM%ALab/
Test_file%Ftest.jpg'"
Adds a new resource. The resource name is ’New Image’, %P (protocol) is an HTTP, %H
(host name) is AMX.COM, %A (file path) is Lab/Test file, and %F (file name) is test.jpg.
162
7" Modero Widescreen Touch Panels
Troubleshooting
Troubleshooting
This section describes the solutions to possible hardware/firmware issues that could arise during the
common operation of a Modero touch panel.
Troubleshooting Information
Symptom
Solution
My USB drivers has a yellow
exclamation point and doesn’t
appear to be working.
The USB driver was incorrectly installed and should be re-installed:
• Power up the panel without the USB cable connected to the panel.
• Plug in the USB cable into the G4 panel. You should see a USB icon
show up in the System Tray.
• Double click on the icon to bring up the list of USB devices (you
should see the "AMX USB LAN LINK" device in the list).
• If the "Install Driver" dialog doesn't appear automatically, select the
"Properties" button and then the "Update Driver" button.
• When the Install Driver dialog does appear, click Next to accept all
the default prompts.
• The OS will notify you that the driver you are installing/updating does
not have a digital signature. This is acceptable, agree to continue the
installation.
• After installation is complete, the exclamation point should disappear.
• During a WebControl connection to a target panel you are prompted
When using G4 WebControl to
with a G4 Authentication dialog which asks you to enter the assigned
communicate with a target panel, a
password for the panel (before gaining access).
VNC Server dialog appears on my
screen.
• If you are ever prompted with a VNC Server dialog, you must enter
the IP Address of the target panel. This can be found within the
Setup > Protected Setup > System Connection page.
- This IP Address of the panel appears within the IP Settings
section of this page
• Enter the IP Address and click OK. You will then be prompted with the
G4 Authentication popup where you must enter the panel’s
WebControl password.
While attempting to communicate
directly with the Virtual Master (on
the PC) via a USB connection, I
can’t get my communication icon
to turn Green.
• A Green communication icon indicates that a connection has been
established to the target Master or target Virtual Master.
• Launch NetLinx Studio and configure the Master Connection
communication settings for a Virtual Master.
• Navigate to the System connection page and toggle the
Type field to USB.
• Make sure the Type-A USB connector is securely connected to the
PC.
• Make sure the panel DOESN’T have the mini-USB connected and
TURN OFF the panel.
• Once the panel has turned ON THEN connect the mini-USB to the
Program Port. The USB icon should appear in your system tray. If it
doesn’t, refer to the Configuring and Using USB with a Virtual
Master section on page 49.
• The panel can take a few minutes to detect the connection to the PC.
7" Modero Widescreen Touch Panels
163
Troubleshooting
Troubleshooting Information (Cont.)
Symptom
Solution
I updated my panel firmware but
my Battery Base page doesn’t
seem to be working properly.
• Cycle power manually to the panel and check the Battery Base page
after startup.
• Verify that you are using the most current v2.XX Modero firmware.
• If downloading the firmware to the panel via a COM port, try using an
IP Address and retry the download of the firmware to the panel.
My Modero panel isn’t appearing
in my Workspace window.
• Verify that the System number is the same on both the NetLinx
Workspace window and the System Connection page on the Modero
panel.
• Verify you have entered the proper NetLinx Master IP and connection
methods into the Master Connection section of the System
Connection page.
My Modero panel can’t obtain a
DHCP Address
In requesting a DHCP Address, the DHCP Server can take up to a few
minutes to provide the address.
• Verify there is an active Ethernet connection attached to the rear of
the Modero before beginning these procedures.
• Select Diagnostics > Network Address, from the Main menu and
verify the System number.
• If the IP Address field is still empty, give the Modero a few minutes to
negotiate a DHCP Address and try again.
My NXT-BP battery pack is
blinking when I check the battery
life indicator.
• A blinking battery life LED indicates that there is less than 10% power
charge remaining on the battery.
• It is recommended that you fully charge the battery either in the
NXA-BASE/1 battery base or in the NXT-CHG battery charger.
• Refer to the NXA-BASE/1 Battery Base Kit (FG2255-05K) section on
page 22 and NXT-CHG Battery Charger Kit (FG2255-50K) section
on page 25 for more information.
My panel is not showing up in the
Virtual Master’s System list of
connected devices.
If you a Virtual Master has already connected to the target panel, the
G4 device retains the information of the previous Virtual Master System
number.
• Reboot the panel without the USB cable plugged into the panel.
•Configure NetLinx Studio for a Virtual Master connection. Note the
System Number used in the Edit Settings window.
• Stop communication on the Virtual Master by going to Settings >
Stop Communications.
• Click Yes to stop communication.
• Select the System Number (from the Online Tree tab) and use a right
mouse click to select Refresh System. This re-establishes
communication with the Virtual Master.
• Plug-in the mini-USB cable into the corresponding port on the panel.
• Wait a few seconds and refresh the system. This re-establishes
communication with the Virtual Master. The panel should now
appear in the list of available devices.
164
7" Modero Widescreen Touch Panels
Troubleshooting
Troubleshooting Information (Cont.)
Symptom
Solution
My Connection Status button isn’t
blinking and it says the USB is
connecting.
"USB Connecting" is displayed when the panel is trying to establish
USB communication with the PC (either within the NetLinx Studio or
TPDesign4 applications).
• Remove the USB connector from the panel and close any AMX
applications.
• Reboot the panel.
• Launch the AMX application and attempt reconnect to the panel.
• If using Studio for Virtual Master communication, establish a Virtual
Master connection, verify the correct System number, stop
communication with the Virtual Master, and then re-establish
communication by refreshing the system.
• After the panel powers-up, reconnect the USB connector to the panel.
• Verify that you have a valid USB connection from within your System
Tray.
My on-screen mouse cursor
doesn’t appear.
• The USB connections are not detected until after the particular USB
connection plugged into the corresponding port on the panel and
power is cycled to the panel.
Calibration is not working.
• After the Modero touch panel has been updated with a new firmware
kit (downloaded to the panel through NetLinx Studio), the calibration
could need to be reset.
• Cycling power to the panel should provide a baseline calibration for
the particular touch panel. Proceed to the Calibration page and reset
the on-screen calibration.
Panel doesn’t respond to my
touches
• The protective cover acts to press on the entire LCD and makes
calibration difficult because the user can’t calibrate on specific
crosshairs when the sheet is pressing on the whole LCD.
• Verify that the protective laminate coating on the LCD is removed
before beginning any calibration process.
There is a crawling, dashed line on • On some units at some resolutions, there are wavy lines across the
the left border of the graphics.
entire screen. This has been seen on middle resolutions and is
referred to as the "Mid Range Fallout" problem.
• This is due to the graphics controller settings in the firmware.
• Update to the latest v2.XX.XX firmware.
• Visit the www.amx.com > Tech Center > Downloadable Files >
Firmware Files > Modero panels. Then Download the KIT file to
your computer.
I was using the power from
PSN4.4, and when I connected my
NXA-BASE/1 battery base to the
active panel, my screen went
blank.
Modero battery bases can not be "hot-swapped" or replaced without
powering down the Modero and removing the PSN4.4 connector.
• If you are currently using a direct power connection to the panel and
then wish to connect an NXA-BASE/1.
- First, power-down the panel and detach the rear power connection.
Then, remove any batteries from within the NXA-BASE/1 and
connect the battery base to the underside of the panel.
- After connecting the base to the un-powered panel, then run power
to the panel by either reconnecting the power cable to the rear of
the panel or inserting the NXT-BP batteries into the NXA-BASE/1.
• Refer to the NXA-BASE/1 Battery Base Kit (FG2255-05K) section on
page 22 and Installing the NXA-BASE/1 below an NXT-CV7
Panel section on page 24 for more information.
7" Modero Widescreen Touch Panels
165
Troubleshooting
Troubleshooting Information (Cont.)
Symptom
Solution
I can’t seem to completely charge
my battery from within an
NXA-BASE/1 connected to a
powered panel.
NXT-BP batteries can be charged from either an external NXT-CHG
battery charger or from within the NXA-BASE/1 located below an NXT
panel.
• The NXA-BASE/1 Battery base should be updated with the latest
firmware (part of the Modero firmware KIT file) from www.amx.com.
• The base can only charge the battery while the NXT panel is in Sleep
Mode. If the panel parameters are set to their highest values, the
priority for the power draw becomes the active panel functions and
no power is routed to the base for charging.
• Adjust the Display Timeout value to allow the panel to commence the
Sleep Mode and begin charging batteries within the base (drawing
power from a PSN4.4).
• Refer to the Battery Base Page section on page 95 for more
information.
My WEP doesn’t seem to be
working.
• WEP will not work unless the same default key is set on both the
panel and the Access Point.
• For example: if you had your access point set to default key 4 (which
was 01:02:03:04:05) you must also set the Modero’s panel key 4 to
01:02:03:04:05.
NetLinx Studio only detects one of
my connected Masters.
Each Master is give a Device Address of 00000.
• Only one Master can be assigned to a particular System number. If
you want to work with multiple Masters, open different instances of
NetLinx Studio and assign each Master its own System value.
• Example: a site has an NXC-ME260/64 and an NI-4000. In order to
work with both units. The ME260/64 can be assigned System #1 and
the NI-4000 can then be assigned System #2 using two open
sessions of NetLinx Studio 2.3.
I can’t seem to connect to a
NetLinx Master using my
NetLinx Studio 2.3.
• From the Settings > Master Comm Settings > Communication
Settings > Settings (for TCP/IP), uncheck the "Automatically Ping
the Master Controller to ensure availability".
• The pinging is to determine if the Master is available, and to reply with
a connection failure instantly if it is not. Without using the ping
feature, you will still attempt to make a connection, but a failure will
take longer to be recognized. Some firewalls and networks do not
allow pinging, though, and the ping will then always result in a failure.
• When connecting to a NetLinx Master controller via TCP/IP, the
program will first try to ping the controller before attempting a
connection. Pinging a device is relatively fast and will determine if the
device is off-line, or if the TCP/IP address that was entered was
incorrect. If you decide NOT to ping for availability and the controller
is off-line, or you have an incorrect TCP/IP address, the program will
try for 30-45 seconds to establish a connection.
Note: If you are trying to connect to a master controller that is behind a
firewall, you may have to uncheck this option. Most firewalls will not
allow ping requests to pass through for security reasons.
166
7" Modero Widescreen Touch Panels
Troubleshooting
Troubleshooting Information (Cont.)
Symptom
Solution
I have more that one Modero panel Multiple NetLinx Compatible devices (such as Modero panels) can be
associated for use with a single Master. Each Modero panel comes
connected to my System Master
with a defaulted Device Number value of 10001. When using multiple
and only one shows up.
panels, it can become very easy to overlook the need to assign
different Device Number values to each panel.
• Press and hold the grey Front Setup Access button for 3 seconds to
open the Setup page.
• Press the Protected Setup button (located on the lower-left of the
panel page), enter 1988 into the on-screen Keypad’s password field,
and press Done when finished.
• Enter a Device Number value for the panel into the Device Number
Keypad. The default is 10001 and the range is from 1 - 32000.
After downloading a panel file or
firmware to a G4 device, the panel
behaves strangely.
Symptoms include:
• Having to repeat the download.
• Inability to make further downloads to the panel. May get "directory"
errors, "graphics hierarchy" errors, etc.… indicating problems with
the Compact Flash.
• Panel will not boot, or gets stuck on "AMX" splash screen.
• Other problems also started after downloading to a new panel or a
panel with a TPD4 file that takes up a considerable amount of the
available Compact Flash.
Cause:
• If the G4 device already contains a large enough file, subsequent
downloads will take up more space than is available and could often
corrupt the Compact Flash. The demo file that typically ships with G4
panels is one such file.
Solution:
• DO NOT download TPD4 files (of large size) over the demo pages, or
any other large TPD4 file.
• First download a small blank one page file to the G4 panel using the
Normal Transfer option to send/download the page. Reboot the
device, then do your regular file or firmware download.
My NXA-BASE/1 Battery Base isn’t The battery base CAN NOT be "hot swapped". This swapping
occurs when an NXT panel is currently being powered by a PSN4.4
being recognized by the NXT
and then is connected to a battery base containing NXT-BP batteries.
touch panel.
Introducing a new power source onto an existing configuration can
damage the NXA-BASE.
Solution:
If your base is not being recognized by the touch panel but is still
providing power:
• Launch the latest NetLinx Studio.
• Refresh the particular System from within the OnLine Tree tab.
• Identify the NXT panel using the battery base.
• From the Main menu go to Tools > Firmware Transfers > Send to
NetLinx Device.
• Locate and select the 2255_XXX_v2_00 KIT file for the battery base.
• Enter the Device and System values, verify the method of
communication (IP recommended).
• Click Send to reload the new base KIT file onto the NXA-BASE/1.
If this above steps do not cause the base to be recognized by the NXT
touch panel on the Setup page, contact AMX Technical Support for
further assistance.
7" Modero Widescreen Touch Panels
167
Troubleshooting
168
7" Modero Widescreen Touch Panels
Appendix
Appendix
Text Formatting Codes for Bargraphs/Joysticks
Text formatting codes for bargraphs provide a mechanism to allow a portion of a bargraphs text to
be dynamically provided information about the current status of the level (multistate and
traditional). These codes would be entered into the text field along with any other text.
The following is a code list used for bargraphs:
Bargraph Text Code Inputs
Code
Bargraph
Multi-State Bargraph
$P
Display the current percentage of the
bargraph (derived from the Adjusted
Level Value as it falls between the
Range Values)
Display the current percentage of the
bargraph (derived from the Adjusted
Level Value as it falls between the
Range Values)
$V
Raw Level Value
Raw Level Value
$L
Range Low Value
Range Low Value
$H
Range High Value
Range High Value
$S
N/A
Current State
$A
Adjusted Level Value (Range Low Value Adjusted Level Value (Range Low Value
subtracted from the Raw Level Value)
subtracted from the Raw Level Value)
$R
Low Range subtracted from the High
Range
Low Range subtracted from the High
Range
$$
Dollar sign
Dollar sign
Buy changing the text on a button (via a VT command) you can modify the codes on a button.
When one of the Text Formatting Codes is encountered by the firmware it is replaced with the
correct value. These values are derived from the following operations:
Formatting Code Operations
Code
Operation
$P
(Current Value - Range Low Value / Range High Value - Range Low Value) x 100
$V
Current Level Value
$L
Range Low Value
$H
Range High Value
$S
Current State (if regular bargraph then resolves to nothing)
$A
Current Value - Range Low Value
$R
Range High Value - Range Low Value
Given a current raw level value of 532, a range low value of 500 and a high range value of 600 the
following text formatting codes would yield the following strings as shown in the table below:
Example
Format
Display
$P%
32%
$A out of $R
32 out of 100
$A of 0 - $R
32 of 0 - 100
$V of $L - $H
532 of 500 - 600
7" Modero Widescreen Touch Panels
169
Appendix
Text Area Input Masking
Text Area Input Masking can be used to limit the allowed/correct characters that are entered into a
text area. For example, in working with a zip code, a user could limit the entry to a max length of
only 5 characters but, with input masking, you could limit them to 5 mandatory numerical digits
and 4 optional numerical digits. A possible use for this feature is to enter information into form
fields. The purpose of this feature is to:
• Force you to use correct type of characters (i.e. numbers vs. characters)
• Limit the number of characters in a text area
• Suggest proper format with fixed characters
• Right to Left
• Required or Optional
• Change/Force a Case
• Create multiple logical fields
• Specify range of characters/number for each field
With this feature, it is NOT necessary to:
• Limit you to a choice of selections
• Handle complex input tasks such as names, days of the weeks or months by name
• Perform complex validation such as Subnet Mask validation
Input mask character types
These character types define what information is allowed to be entered in any specific instance. The
following table lists what characters in an input mask will define what characters are allowed in any
given position.
Character Types
Character
Masking Rule
0
Digit (0 to 9, entry required, plus [+] and minus [-] signs not allowed)
9
Digit or space (entry not required, plus and minus signs not allowed)
#
Digit or space (entry not required; plus and minus signs allowed)
L
Letter (A to Z, entry required)
?
Letter (A to Z, entry optional)
A
Letter or digit (entry required)
a
Letter or digit (entry optional)
&
Any character or a space (entry required)
C
Any character or a space (entry optional)
The number of the above characters used determines the length of the input masking
box. Example: 0000 requires an entry, requires digits to be used, and allows only 4
characters to be entered/used.
Refer to the following Send Commands for more detailed information:
• ^BIM - Sets the input mask for the specified addresses. (see the ^BIM section on
page 128).
• ^BMF subcommand %MK - sets the input mask of a text area (see the
^BMF section on page 130).
170
7" Modero Widescreen Touch Panels
Appendix
Input mask ranges
These ranges allow a user to specify the minimum and maximum numeric value for a field. Only
one range is allowed per field. Using a range implies a numeric entry ONLY.
Input Mask Ranges
Character
Meaning
[
Start range
]
End range
|
Range Separator
An example from the above table:
[0|255] This allows a user to enter a value from 0 to 255.
Input mask next field characters
These characters allow you to specify a list of characters that cause the keyboard to move the focus
to the next field when pressed instead of inserting the text into the text area.
Input Mask Next Field Char
Character
Meaning
{
Start Next Field List
}
End Next Field List
An example from the above table:
{.} or {:} or {.:} Tells the system that after a user hits any of these keys, proceed to the
next text area input box.
Input mask operations
Input Mask Operators change the behavior of the field in the following way:
Input Mask Operators
Character
Meaning
<
Forces all characters to be converted to lowercase
>
Forces all characters to be converted to uppercase
^
Sets the overflow flag for this field
Input mask literals
To define a literal character, enter any character, other than those shown in the above table
(including spaces, and symbols). A back-slash ('\') causes the character that follows it to be
displayed as the literal character. For example, \A is displayed just as the letter A. To define one of
the following characters as a literal character, precede that character with a back-slash. Text entry
operation using Input Masks
A keyboard entry using normal text entry is straightforward. However, once an input mask is
applied, the behavior of the keyboard needs to change to accommodate the input mask's
requirement. When working with masks, any literal characters in the mask will be "skipped" by any
cursor movement including cursor keys, backspace, and delete.
7" Modero Widescreen Touch Panels
171
Appendix
When operating with a mask, the mask should be displayed with placeholders. The "-" character
should display where you should enter a character. The arrow keys will move between the "-"
characters and allow you to replace them. The text entry code operates as if it is in the overwrite
mode. If the cursor is positioned on a character already entered and you type in a new (and valid)
character, the new character replace the old character. There is no shifting of characters.
When working with ranges specified by the [] mask, the keyboard allows you to enter a number
between the values listed in the ranges. If a user enters a value that is larger than the max, the
maximum number of right-most characters is used to create a new, acceptable value.
Example 1: If you type "125" into a field accepting 0-100, then the values displayed will
be "1", "12", "25".
Example2: If the max for the filed was 20, then the values displayed will
be "1", "12", "5".
When data overflows from a numerical field, the overflow value is added to the previous field on
the chain, if the overflow character was specified. In the above example, if the overflow flag was
set, the first example will place the "1" into the previous logical field and the second example will
place "12" in the previous logical field. If the overflow filed already contains a value, the new value
will be inserted to the right of the current characters and the overflow field will be evaluated.
Overflow continues to work until a filed with no overflow value is set or there are no more fields
left (i.e. reached first field).
If a character is typed and that characters appear in the Next Field list, the keyboard should move
the focus to the next field. For example, when entering time, a ":" is used as a next field character.
If you hit "1:2", the 1 is entered in the current field (hours) and then the focus is moved to the next
field and 2 is entered in that field.
When entering time in a 12-hour format, entry of AM and PM is required. Instead of adding
AM/PM to the input mask specification, the AM/PM should be handled within the NetLinx code.
This allows a programmer to show/hide and provide discrete feedback for AM and PM.
Input mask output examples
The following are some common input masking examples:
Output Examples
Common Name
172
Input Mask
Input
IP Address Quad
[0|255]{.}
Any value from 0 to 255
Hour
[1|12]{:}
Any value from 1 to 12
Minute/Second
[0|59]{:}
Any value from 0 to 59
Frames
[0|29]{:}
Any value from 0 to 29
Phone Numbers
(999) 000-0000
(555) 555-5555
Zip Code
00000-9999
75082-4567
7" Modero Widescreen Touch Panels
Appendix
URL Resources
A URL can be broken into several parts. For example: the URL http://www.amx.com/companyinfo-home.asp. This URL indicates that the protocol in use is http (HyperText Transport Protocol)
and that the information resides on a host machine named www.amx.com. The image on that host
machine is given an assignment (by the program) name of company-info-home.asp (Active Server
Page).
The exact meaning of this name on the host machine is both protocol dependent and host
dependent. The information normally resides in a file, but it could be generated dynamically. This
component of the URL is called the file component, even though the information is not necessarily
in a file.
A URL can optionally specify a port, which is the port number to which the TCP connection is
made on the remote host machine. If the port is not specified, the default port for the protocol is
used instead. For example, the default port for http is 80. An alternative port could be specified as:
http://www.amx.com:8080/company-info-home.asp.
Any legal HTTP syntax can be used.
Special escape sequences
The system has only a limited knowledge of URL formats in that it transparently passes the URL
information onto the server for translation. A user can then pass any parameters to the server side
programs such as CGI scripts or active server pages. However; the system will parse the URL
looking for special escape codes. When it finds an escape code it replaces that code with a
particular piece of panel, button, or state information.
For example, "http://www.amx.com/img.asp?device=$DV" would become "http://www.amx.com/
img.asp?device=10001". Other used escape sequences include:
Escape Sequences
Sequence
Panel Information
$DV
Device Number
$SY
System Number
$IP
IP Address
$HN
Host Name
$MC
Mac Address
$ID
Neuron ID
$PX
X Resolution of current panel mode/file
$PY
Y Resolution of current panel mode/file
$BX
X Resolution of current button
$BY
Y Resolution of current button
$BN
Name of button
$ST
Current state
$AC
Address Code
$AP
Address Port
$CC
Channel Code
7" Modero Widescreen Touch Panels
173
Appendix
Escape Sequences (Cont.)
174
Sequence
Panel Information
$CP
Channel Port
$LC
Level Code
$LP
Level Port
7" Modero Widescreen Touch Panels
Appendix
7" Widescreen Modero Touch Panels
175
ARGENTINA • AUSTRALIA • BELGIUM • BRAZIL • CANADA • CHINA • ENGLAND • FRANCE • GERMANY • GREECE • HONG KONG • INDIA • INDONESIA • ITALY • JAPAN
LEBANON • MALAYSIA • MEXICO • NETHERLANDS • NEW ZEALAND • PHILIPPINES • PORTUGAL • RUSSIA • SINGAPORE • SPAIN • SWITZERLAND • THAILAND • TURKEY • USA
ATLANTA • BOSTON • CHICAGO • CLEVELAND • DALLAS • DENVER • INDIANAPOLIS • LOS ANGELES • MINNEAPOLIS • PHILADELPHIA • PHOENIX • PORTLAND • SPOKANE • TAMPA
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.222.0193 • 469.624.8000 • 469-624-7153 fax • 800.932.6993 technical support • www.amx.com
Last Revision: 15/08/04
036-004-2740 8/05 ©2005 AMX Corporation. All rights reserved. AMX, the AMX logo, the building icon, the home icon, and the light bulb icon are all trademarks of AMX Corporation.
In Canada doing business as Panja Inc.
AMX reserves the right to alter specifications without notice at any time.