Analog Devices EZ-Extender Network Card User Manual

SHARC® EZ-Extender®
Manual
Revision 3.0, April 2006
Part Number
82-000805-01
Analog Devices, Inc.
One Technology Way
Norwood, Mass. 02062-9106
a
Copyright Information
©2006 Analog Devices, Inc., ALL RIGHTS RESERVED. This document
may not be reproduced in any form without prior, express written consent
from Analog Devices, Inc.
Printed in the USA.
Limited Warranty
The SHARC EZ-Extender is warranted against defects in materials and
workmanship for a period of one year from the date of purchase from
Analog Devices or from an authorized dealer.
Disclaimer
Analog Devices, Inc. reserves the right to change this product without
prior notice. Information furnished by Analog Devices is believed to be
accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use; nor for any infringement of patents or other rights of
third parties which may result from its use. No license is granted by implication or otherwise under the patent rights of Analog Devices, Inc.
Trademark and Service Mark Notice
The Analog Devices logo, SHARC, VisualDSP++, EZ-KIT Lite, and
EZ-Extender are registered trademarks of Analog Devices, Inc.
All other brand and product names are trademarks or service marks of
their respective owners.
Regulatory Compliance
The SHARC EZ-Extender has been certified to comply with the essential
requirements of the European EMC directive 89/336/EEC (inclusive
93/68/EEC) and, therefore, carries the “CE” mark.
The SHARC EZ-Extender has been appended to Analog Devices Development Tools Technical Construction File referenced “DSPTOOLS1”
dated December 21, 1997 and was awarded CE Certification by an
appointed European Competent Body and is on file.
The EZ-KIT Lite evaluation system contains ESD
(electrostatic discharge) sensitive devices. Electrostatic charges readily accumulate on the human
body and equipment and can discharge without
detection. Permanent damage may occur on devices
subjected to high-energy discharges. Proper ESD
precautions are recommended to avoid performance
degradation or loss of functionality. Store unused
EZ-KIT Lite boards in the protective shipping
package.
iv
SHARC EZ-Extender Manual
CONTENTS
PREFACE
Purpose of This Manual ................................................................ viii
Intended Audience .......................................................................... ix
Manual Contents ............................................................................ ix
What’s New in This Manual ............................................................. x
Technical or Customer Support ........................................................ x
Supported Products ......................................................................... xi
Product Information ....................................................................... xi
MyAnalog.com .......................................................................... xi
Processor Product Information .................................................. xii
Related Documents .................................................................. xii
Online Technical Documentation ............................................. xiv
Notation Conventions ..................................................................... xv
EZ-EXTENDER INTERFACES
ADC HSC Interface ...................................................................... 1-1
Breadboard Area ........................................................................... 1-2
EZ-EXTENDER HARDWARE REFERENCE
System Architecture ...................................................................... 2-1
SHARC EZ-Extender Manual
v
CONTENTS
DIP Switches and Jumpers ............................................................ 2-3
Direction/Clock Source Control Switch (SW1) ........................ 2-3
MISO Disconnect Jumper (P6) ............................................... 2-5
SMA Connector Clock Disconnect Jumper (P10) .................... 2-5
EZ-EXTENDER BILL OF MATERIALS
EZ-EXTENDER SCHEMATIC
Title Page ..................................................................................... B-1
Expansion Connector P1 .............................................................. B-2
Expansion Connecor P2 ............................................................... B-3
Expansion Connector P3 .............................................................. B-4
HSC Inteface ................................................................................ B-5
Control - SPI Interface ................................................................. B-6
Breadboard Area Footprints .......................................................... B-7
INDEX
vi
SHARC EZ-Extender Manual
PREFACE
Thank you for purchasing the SHARC® EZ-Extender®, Analog Devices
(ADI) extension board to the EZ-KIT Lite® evaluation system for
ADSP-21262 SHARC processors.
The SHARC processors are based on a 32-bit super Harvard architecture
that includes a unique memory architecture comprised of two large
on-chip, dual-ported SRAM blocks coupled with a sophisticated IO processor, which gives SHARC the bandwidth for sustained high-speed
computations. SHARC represents today’s de facto standard for floating-point processors targeted for premium audio applications.
The SHARC EZ-Extender is designed to be used in conjunction with the
ADSP-21262 EZ-KIT Lite evaluation system. The EZ-KIT Lite includes
an evaluation suite of VisualDSP++® software, which is limited in program memory size for use solely with the EZ-KIT Lite product.
VisualDSP++ is a powerful programming tool with flexibility that significantly decreases the time required to port software code to a processor,
reducing time-to-market.
To learn more about Analog Devices development software, go to
http://www.analog.com/dsp/tools/.
Example programs are available to demonstrate the capabilities of the
SHARC EZ-Extender board.
The SHARC EZ-Extender is a separately sold assembly that plugs onto
the expansion interface of the ADSP-21262 EZ-KIT Lite evaluation
system.
SHARC EZ-Extender Manual
vii
Purpose of This Manual
The board extends the capabilities of the evaluation system by providing a
connection between the parallel data access port (PDAP) of the
ADSP-21262 processor and an Analog Devices analog-to-digital
high-speed converter (ADC HSC) evaluation board. Moreover, the
extender broadens the range of the EZ-KIT Lite applications by providing
surface-mounted (SMT) footprints for breadboard capabilities and access
to all of the pins on the EZ-KIT Lite’s expansion interface.
The extender features:
• High-speed converter evaluation board interface
D
D
D
40-pin, right angle, 0.1 in. spacing, female socket to connect to analog-to-digital converter boards
Switches for routing and direction selection
RJ-45 with serial peripheral interconnect (SPI) to configure
converter registers
• SMT footprint area
D
D
1206 and 805 footprints
SOIC24 and SOIC20 footprints
• Dimensions
D
5 in (H) x 5 in (W)
Purpose of This Manual
The SHARC EZ-Extender Manual describes the operation and configuration of the components on the board. A schematic and a bill of materials
are provided as a reference for future ADSP-21262 processor board
designs.
viii
SHARC EZ-Extender Manual
Preface
Intended Audience
This manual is a user’s guide and reference to the SHARC EZ-Extender.
Programmers who are familiar with the Analog Devices SHARC processor
architecture, operation, and development tools are the primary audience
for this manual.
Programmers who are unfamiliar with VisualDSP++ or EZ-KIT Lite evaluation software should refer to the ADSP-21262 EZ-KIT Lite Evaluation
System Manual, VisualDSP++ online Help, and user’s or getting started
guides. For the locations of these documents, refer to “Related
Documents”.
Manual Contents
The manual consists of:
• Chapter 1, “EZ-Extender Interfaces” on page 1-1
Provides basic board information.
• Chapter 2, “EZ-Extender Hardware Reference” on page 2-1
Provides information on the hardware aspects of the board.
• Appendix A, “EZ-Extender Bill Of Materials” on page A-1
Provides a list of components used to manufacture the SHARC
EZ-Extender board.
SHARC EZ-Extender Manual
ix
What’s New in This Manual
• Appendix B,“EZ-Extender Schematic” on page B-1
Provides the resources to allow modifications to the EZ-Extender
or to use as a reference design.
B now is part of the online Help. The PDF version of
L Appendix
the SHARC EZ-Extender Manual is located in the
Docs\EZ-KIT
Lite Manuals folder on the installation CD. Alternatively, the
book can be found at the Analog Devices Web site,
www.analog.com/processors.
What’s New in This Manual
This edition of the SHARC EZ-Extender Manual has been updated for the
latest revision of VisualDSP++.
Technical or Customer Support
You can reach Analog Devices, Inc. Customer Support in the following
ways:
• Visit the Embedded Processing and DSP products Web site at
http://www.analog.com/processors/technicalSupport
• E-mail tools questions to
processor.tools.support@analog.com
• E-mail processor questions to
processor.support@analog.com (World wide support)
processor.europe@analog.com (Europe support)
processor.china@analog.com (China support)
• Phone questions to 1-800-ANALOGD
x
SHARC EZ-Extender Manual
Preface
• Contact your Analog Devices, Inc. local sales office or authorized
distributor
• Send questions by mail to:
Analog Devices, Inc.
One Technology Way
P.O. Box 9106
Norwood, MA 02062-9106
USA
Supported Products
The SHARC EZ-Extender is designed as an extension to the ADSP-21262
EZ-KIT Lite evaluation system.
Product Information
You can obtain product information from the Analog Devices Web site,
from the product CD-ROM, or from the printed publications (manuals).
Analog Devices is online at www.analog.com. Our Web site provides information about a broad range of products—analog integrated circuits,
amplifiers, converters, and digital signal processors.
MyAnalog.com
MyAnalog.com is a free feature of the Analog Devices Web site that allows
customization of a Web page to display only the latest information on
products you are interested in. You can also choose to receive weekly
e-mail notifications containing updates to the Web pages that meet your
interests. MyAnalog.com provides access to books, application notes, data
sheets, code examples, and more.
SHARC EZ-Extender Manual
xi
Product Information
Registration:
Visit www.myanalog.com to sign up. Click Register to use MyAnalog.com.
Registration takes about five minutes and serves as means for you to select
the information you want to receive.
If you are already a registered user, just log on. Your user name is your
e-mail address.
Processor Product Information
For information on embedded processors and DSPs, visit our Web site at
www.analog.com/processors, which provides access to technical publications, data sheets, application notes, product overviews, and product
announcements.
You may also obtain additional information about Analog Devices and its
products in any of the following ways.
• E-mail questions or requests for information to
processor.support@analog.com (World wide support)
processor.europe@analog.com (Europe support)
processor.china@analog.com (China support)
• Fax questions or requests for information to
1-781-461-3010 (North America)
+49-89-76903-157 (Europe)
Related Documents
For information on product-related development software, see the
following publications.
xii
SHARC EZ-Extender Manual
Preface
Table 1. Related Processor Publications
Title
Description
ADSP-21262 SHARC Microprocessor Datasheet
General functional description, pinout, and
timing
ADSP-2126x SHARC DSP Core Manual
ADSP-2126x SHARC DSP Peripherals Manual
Description of internal processor architecture,
registers, and all peripheral functions
ADSP-21160 SHARC DSP Instruction Set
Reference
Description of all allowed processor assembly
instructions
Table 2. Related VisualDSP++ Publications
Title
Description
VisualDSP++ Assembler and Preprocessor
Manual for SHARC Processors
Description of the assembler function and
commands for SHARC processors
VisualDSP++ C/C++ Complier and Library
Manual for SHARC Processors
Description of the complier function and
commands for SHARC processors
VisualDSP++ Linker and Utilities Manual
Description of the linker function and
commands for the processors
VisualDSP++ Loader and Utilities Manual
Description of the loader function and
commands for the processors
VisualDSP++ User’s Guide
Detailed description of VisualDSP++ features
and usage
you plan to use the EZ-KIT Lite board in conjunction with a
L IfJTAG
emulator, also refer to the documentation that accompanies
the emulator.
All documentation is available online. Most documentation is available in
printed form.
Visit the Technical Library Web site to access all processor and tools
manuals and data sheets:
http://www.analog.com/processors/resources/technicalLibrary.
SHARC EZ-Extender Manual
xiii
Product Information
Online Technical Documentation
Online documentation comprises the VisualDSP++ Help system, software
tools manuals, hardware tools manuals, processor manuals, the Dinkum
Abridged C++ library, and Flexible License Manager (FlexLM) network
license manager software documentation. You can easily search across the
entire VisualDSP++ documentation set for any topic of interest. For easy
printing, supplementary .PDF files of most manuals are provided in the
Docs folder on the VisualDSP++ installation CD.
Each documentation file type is described as follows.
File
Description
.CHM
Help system files and manuals in Help format
.HTM or
.HTML
Dinkum Abridged C++ library and FlexLM network license manager software
documentation. Viewing and printing the .HTML files requires a browser, such as
Internet Explorer 5.01 (or higher).
.PDF
VisualDSP++ and processor manuals in Portable Documentation Format (PDF).
Viewing and printing the .PDF files requires a PDF reader, such as Adobe Acrobat
Reader (4.0 or higher).
If documentation is not installed on your system as part of the software
installation, you can add it from the VisualDSP++ CD at any time by
running the Tools installation. Access the online documentation from the
VisualDSP++ environment, Windows® Explorer, or the Analog Devices
Web site.
xiv
SHARC EZ-Extender Manual
Preface
Notation Conventions
Text conventions used in this manual are identified and described as
follows.
Example
Description
{this | that}
Alternative required items in syntax descriptions appear within curly
brackets and separated by vertical bars; read the example as this or
that. One or the other is required.
[this | that]
Optional items in syntax descriptions appear within brackets and separated by vertical bars; read the example as an optional this or that.
[this,…]
Optional item lists in syntax descriptions appear within brackets
delimited by commas and terminated with an ellipse; read the example
as an optional comma-separated list of this.
.SECTION
Commands, directives, keywords, and feature names are in text with
letter gothic font.
filename
Non-keyword placeholders appear in text with italic style format.
L
Note: For correct operation, ...
A Note provides supplementary information on a related topic. In the
online version of this book, the word Note appears instead of this
symbol.
a
Caution: Incorrect device operation may result if ...
Caution: Device damage may result if ...
A Caution identifies conditions or inappropriate usage of the product
that could lead to undesirable results or product damage. In the online
version of this book, the word Caution appears instead of this symbol.
[
Warning: Injury to device users may result if ...
A Warning identifies conditions or inappropriate usage of the product
that could lead to conditions that are potentially hazardous for the
devices users. In the online version of this book, the word Warning
appears instead of this symbol.
conventions, which apply only to specific chapters, may
L Additional
appear throughout this document.
SHARC EZ-Extender Manual
xv
Notation Conventions
xvi
SHARC EZ-Extender Manual
1 EZ-EXTENDER INTERFACES
This chapter relates how the extender interfaces with the compatible
boards. The information is presented in the following sections.
• “ADC HSC Interface” on page 1-1
• “Breadboard Area” on page 1-2
ADC HSC Interface
The SHARC EZ-Extender can connect to an analog-to-digital high-speed
converter (ADC HSC) evaluation board via the ADC HSC interface. The
ADC HSC interface consists of a 40-pin female header, which contains all
of the control and data signals necessary to transfer data between the parallel data access port (PDAP) of the processor and the HSC evaluation
board. Additionally, the extender provides a RJ-45 connector, which contains all of the serial peripheral interconnect (SPI) signals necessary to
configure the control registers of capable high-speed converters. For a
block diagram of the ADC HSC interface, see Figure 2-1 on page 2-2.
Before using the SHARC EZ-Extender, familiarize yourself with the documentation and schematics of the target board and the ADSP-21262
EZ-KIT Lite. For example, on the EZ-KIT Lite, it may be necessary to
disable other devices on the PDAP or disable the push buttons.
To configure the SHARC EZ-Extender to connect to an ADC HSC evaluation board, determine the source of the PDAP clock and the direction
of the general-purpose signals, DAI_P15_GP1 and DAI_P16_GP2. To learn
about possible clock settings, refer to “Direction/Clock Source Control
SHARC EZ-Extender Manual
1-1
Breadboard Area
Switch (SW1)” on page 2-3. The setup of the general-purpose signals
DAI_P15_GP1 and DAI_P16_GP2 is dependent on the specific ADC HSC
evaluation board being interfaced; therefore, the board’s model must be
taken into consideration.
The data bus of the EZ-Extender must be enabled before data is read.
Enable the data bus by a memory read from address 0x160 0000, which
the AD[15:0] pins set up as the external port. Then, the AD[15:0] pins can
be set up in PDAP mode.
A list of ADC boards compatible with the extender can be found at
http://www.analog.com/processors/processors/blackfin/technicalLibrary/manuals/pdf/EZ-Extender_to_DSP_Supported.pdf.
Contact
Technical Support for information about available examples. To learn
more about Analog Devices data converters, go to www.analog.com.
Breadboard Area
SHARC EZ-Extender broadens the range of the EZ-KIT Lite applications
by providing surface mounted (SMT) footprints for breadboard capabilities and access to all of the pins on the EZ-KIT Lite’s expansion interface.
1-2
SHARC EZ-Extender Manual
2 EZ-EXTENDER HARDWARE
REFERENCE
This chapter describes the hardware design of the SHARC EZ-Extender.
The following topics are covered.
• “System Architecture” on page 2-1
Describes the configuration of the extender and explains how the
board components interface with the processor and EZ-KIT Lite.
• “DIP Switches and Jumpers” on page 2-3
Describes the function of the configuration DIP switches and
jumpers.
System Architecture
A detailed block diagram of the SHARC EZ-Extenderis shown in
Figure 2-1. Note that the arrow in the bidirectional driver symbols
denotes the direction of the driver when in transmit mode. The bidirectional driver is in transmit mode when the direction pin is pulled high.
Use the diagram in conjunction with information in “DIP Switches and
Jumpers” on page 2-3 section of this manual to configure your SHARC
EZ-Extender.
Before using the SHARC EZ-Extender, familiarize yourself with the documentation and schematics of the target board and the ADSP-21262
EZ-KIT Lite. For example, on the EZ-KIT Lite, it may be necessary to
disable other devices on the parallel data access port (PDAP) or disable the
push buttons.
SHARC EZ-Extender Manual
2-1
System Architecture
Figure 2-1. SHARC EZ-Extender Block Diagram
The block diagram in Figure 2-1 shows that each clock and general-purpose signal attached to the analog-to-digital high-speed converter (ADC
HSC) interface is configured depending on how the interface operates.
The EZ-Extender has two clock signals, TX_CLK and RX_CLK. The TX_CLK
signal is used as an output and can be generated in three ways: by applying
a signal via an SMA connector, by using the RX_CLK signal, or by populat-
2-2
SHARC EZ-Extender Manual
EZ-Extender Hardware Reference
ing a socket with an oscillator. Only one of these sources can be used at a
time, the other sources must be disabled. For more information on how to
disable the TX_CLK sources, see “SMA Connector Clock Disconnect
Jumper (P10)” on page 2-5. The RX_CLK signal is generated by the target
board. Both the TX_CLK and RX_CLK can connect to the processor’s clock-in
signal (DAI_P2_CLOCKIN) as an input. See “Direction/Clock Source Control Switch (SW1)” on page 2-3 for more information.
The ADC interface has two general-purpose signals, DAI_P15_GP1 and
DAI_P16_GP2. The evaluation board with which the extender interfaces
determines how these signals are set up. For information on how to set the
direction and the source of these signals, refer to “Direction/Clock Source
Control Switch (SW1)” on page 2-3.
The ADC interface connects to the PDAP of the ADSP-21262 processor.
The PDAP is multiplexed with the address and data bus. To avoid bus
contention with the memory devices on the EZ-KIT Lite, the driver connected to the data bus of the ADC must be enabled. For more information
about enabling the data bus, see “ADC HSC Interface” on page 1-1.
DIP Switches and Jumpers
The following section describes the function of all of the jumpers and
switches on the EZ-Extender. Before connecting the extender, familiarize
yourself with each possible setting’s effect on your application.
Direction/Clock Source Control Switch (SW1)
A designated DIP switch, SW1, provides an independent direction control
for the general-purpose signals (DAI_P15_GP1 and DAI_P16_GP2), as illustrated in Figure 2-1 on page 2-2. Each signal can be hardwired to be either
transmit or receive, or can be changed in real time using the DAI_P18 processor pin. If the DAI_P18 processor pin is intended for the direction
control, ensure the pin is not used for other purposes on the EZ-KIT Lite.
SHARC EZ-Extender Manual
2-3
DIP Switches and Jumpers
When the SW1 switch connects a direction control signal to ground (GND),
the corresponding signal (signals) is (are) controlled as input. The direction control functionality is summarized in Table 2-1.
Table 2-1. DAI_P15_GP1/DAI_P16_GP2 Direction Control Settings
SW1 Position 3
SW1 Position 5
SW1 Position 4
SW1 Position 6
DAI_P15_GP1 Direction
DAI_P16_GP2 Direction
OFF
OFF
EZ-KIT Lite is transmitter
OFF
ON
DAI_P18 sets the direction:
0 = EZ-KIT Lite is receiver
1 = EZ-KIT Lite is transmitter
ON
OFF
EZ-KIT Lite is receiver
ON
ON
Do not use
The source of the PDAP clock input signal, DAI_PP2_CLOCKIN, is configured through positions 1 and 2 of the DIP switch SW1, as illustrated in
Figure 2-1 on page 2-2. The switch settings are summarized in Table 2-2.
Table 2-2. PDAP Clock-in Source Settings
2-4
SW1 Position 1
RX_CLK
SW1 Position 2
TX_CLK
DIA_P2_CLOCKIN Source
OFF
OFF
Not generated by the EZ-Extender
OFF
ON
In this configuration, the TX_CLK signal must be
generated by one of the user configured clock
sources.
ON
OFF
RX_CLK
ON
ON
RX_CLK;
in this configuration, the RX_CLK signal is
also routed to the TX_CLK to be used as an output.
SHARC EZ-Extender Manual
EZ-Extender Hardware Reference
MISO Disconnect Jumper (P6)
The MISO signal of the serial peripheral interconnect (SPI) connector (J2)
is driven by a buffer to the processor’s MISO signal, as illustrated in
Figure 2-1 on page 2-2. When the SPI connector is not in use, remove the
P6 jumper to prevent the signal from interfering with other devices on the
SPI bus.
SMA Connector Clock Disconnect Jumper (P10)
The SMA connector (J3) enables a clock input from a signal generator or
from other clock source. The input signal is directed though a buffer, as
illustrated in Figure 2-1 on page 2-2. When the SMA connector is not in
use, remove the P10 jumper to prevent the buffer from driving other signals on the net.
SHARC EZ-Extender Manual
2-5
DIP Switches and Jumpers
2-6
SHARC EZ-Extender Manual
A EZ-EXTENDER BILL OF
MATERIALS
The bill of materials corresponds to “EZ-Extender Schematic” on
page B-1. Please check the latest schematic on the Analog Devices Web
site:
http://www.analog.com/Processors/Processors/DevelopmentTools/tec
hnicalLibrary/manuals/DevToolsIndex.html#Evaluation%20Kit%20Manuals.
Ref. Qty.
Description
Reference
Designator
Manufacturer
Part Number
1
1
74LVX244M
SOIC20
U6
FAIRCHILD
74LVX244M
2
1
SN74ALVTH162
44 SSOP48
U1
TI
74ALVTH16244DGGE4
3
1
SN74LVC1G125
SOT23-5
U5
TI
74LVC1G125DBVRE4
4
1
74LVTH16245M
EA SSOP48
U2
FAIRCHILD
74LVTH16245MEA
5
1
SN74LVC1G14D
BVR SOT23-5
U3
DIGI-KEY
296-11607-1-ND
6
1
DIP 8 DIP8SOC
U7
MILL-MAX
614-43-308-31-007000
7
3
0.05 45x2
CON018
P1-3
SAMTEC
TFC-145-32-F-D
8
1
DIP6 SWT017
SW1
C&K
TDA06H0SB1
9
1
IDC 20X2
IDC20X2RASOC
J1
SAMTEC
SSW-120-02-G-D-RA
SHARC EZ-Extender Manual
A-1
A-2
Ref. Qty.
Description
Reference
Designator
Manufacturer
Part Number
10
1
RJ45 8PIN
CON_RJ45
J2
TYCO
1-16609214-1
11
1
SMA XPINS
CON043
J3
JOHNSON
COMP
142-0701-201
12
2
IDC 2X1
IDC2X1
P6,P10
FCI
90726-402HLF
13
2
IDC
2PIN_JUMPER_
SHORT
SJ1-2
DIGI-KEY
S9001-ND
14
1
51 1/8W 5% 1206
R9
VISHAY
CRCW120651R0JKEA
15
14
0.1UF 50V 10%
0805
C3-10,C12,
C14-18
AVX
08055C104KAT
16
16
10K 1/10W 5%
0805
R1-2,R5-7,
R11-12,R16
VISHAY
CRCW080510K0JNEA
17
3
33 1/10W 5%
0805
R10,R13,R18
VISHAY
CRCW080533R0JNEA
18
4
10UF 25V
+80-20% 1210
C1-2,C11,C13
PANASONIC
ECJ4YF1E106Z
19
2
22 1/10W 5%
0805
R3-4
VISHAY
CRCW080522R0JNEA
20
2
1.2K 1/10W 5%
0805
R15,R17
VISHAY
CRCW08051K20JNEA
21
1
10K 1/2W 10%
RES002
R8
COPAL
ELECT
CT9EW103
SHARC EZ-Extender Manual
A
B
C
D
1
1
2
2
ADSP-21262 EZ-Extender 1
3
3
ANALOG
DEVICES
4
Title
Size
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP21262 EX-EXTENDER 1
TITLE
Board No.
C
Date
20 Cotton Road
Rev
A0182-2003
2.0
Sheet
4-24-2006_9:28
D
1
of
7
A
B
C
D
EXPANSION INTERFACE (TYPE A)
5V
5V
5V
1
1
P1_[21:86]
P1_[21:86]
AD[0:15]
P1_[21:86]
AD[0:15]
AD[0:15]
P1A
2
P1
1
2
1
2
AD0
3
4
AD2
3
4
AD4
5
6
AD6
AD0
5
6
AD1
P1B
1
2
AD1
3
4
AD3
AD5
5
6
AD7
AD8
7
8
AD10
AD2
7
8
AD3
AD9
7
8
AD11
AD12
9
10
AD14
AD4
9
10
AD5
AD13
9
10
AD15
P1_21
11
12
P1_23
AD6
11
12
AD7
P1_22
11
12
P1_24
P1_25
13
14
P1_27
AD8
13
14
AD9
P1_26
13
14
P1_28
P1_29
15
16
P1_31
AD10
15
16
AD11
P1_30
15
16
P1_32
P1_33
17
18
P1_35
AD12
17
18
AD13
P1_34
17
18
P1_36
19
20
P1_39
AD14
19
20
AD15
19
20
P1_40
P1_41
21
22
P1_43
P1_21
21
22
P1_22
P1_42
21
22
P1_44
P1_45
23
24
P1_47
P1_23
23
24
P1_24
P1_46
23
24
P1_48
P1_49
25
26
P1_51
P1_25
25
26
P1_26
P1_50
25
26
P1_52
P1_53
27
28
P1_55
P1_27
27
28
P1_28
P1_54
27
28
P1_56
P1_57
29
30
P1_59
P1_29
29
30
P1_30
P1_58
29
30
P1_60
P1_61
31
32
P1_63
P1_31
31
32
P1_32
P1_62
31
32
P1_64
P1_65
33
34
P1_67
P1_33
33
34
P1_34
P1_66
33
34
P1_68
P1_69
35
36
P1_71
P1_35
35
36
P1_36
P1_70
35
36
P1_72
P1_73
37
38
P1_75
37
38
P1_74
37
38
P1_76
P1_77
39
40
P1_79
P1_39
39
40
P1_40
P1_78
39
40
P1_80
P1_81
41
42
P1_83
P1_41
41
42
P1_42
P1_82
41
42
P1_84
P1_85
43
44
P1_43
43
44
P1_44
P1_86
43
44
45
46
P1_45
45
46
P1_46
45
46
P1_47
47
48
P1_48
P1_49
49
50
P1_50
P1_51
51
52
P1_52
P1_53
53
54
P1_54
P1_55
55
56
P1_56
P1_57
57
58
P1_58
P1_59
59
60
P1_60
P1_61
61
62
P1_62
P1_63
63
64
P1_64
P1_65
65
66
P1_66
P1_67
67
68
P1_68
P1_69
69
70
P1_70
P1_71
71
72
P1_72
P1_73
73
74
P1_74
P1_75
75
76
P1_76
P1_77
77
78
P1_78
P1_79
79
80
P1_80
P1_81
81
82
P1_82
P1_83
83
84
P1_84
P1_85
85
86
P1_86
87
88
89
90
IDC23X2
3
2
IDC23X2
3
CON018
5V
4
C1
10UF
1210
ANALOG
DEVICES
C17
0.1UF
0805
Title
Size
Expanison Connector
P1
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP21262 EX-EXTENDER 1
EXPANSION CONNECTOR P1
Board No.
C
Date
20 Cotton Road
Rev
A0182-2003
2.0
Sheet
4-24-2006_9:28
D
2
of
7
A
B
C
D
EXPANSION INTERFACE (TYPE A)
3.3V
1
1
3.3V
3.3V
P2_[5:86]
P2_[5:86]
P2_[5:86]
P2A
1
2
P2_5
3
4
P2_7
P2_9
5
6
P2_11
P2_13
7
8
P2_17
9
10
P2_19
P2_21
11
12
P2_25
13
P2_29
15
P2_33
P2_37
2
P2B
1
2
3
4
P2_6
3
4
P2_8
P2_5
5
6
P2_6
P2_10
5
6
P2_12
P2_7
7
8
P2_8
P2_14
7
8
P2_9
9
10
P2_10
P2_18
9
10
P2_20
P2_23
P2_11
11
12
P2_12
P2_22
11
12
P2_24
14
P2_27
P2_13
13
14
P2_14
P2_26
13
14
P2_28
16
P2_31
15
16
P2_30
15
16
P2_32
17
18
P2_35
P2_17
17
18
P2_18
17
18
P2_36
19
20
P2_39
P2_19
19
20
P2_20
P2_38
19
20
P2_40
P2_41
21
22
P2_43
P2_21
21
22
P2_22
P2_42
21
22
P2_44
P2_45
23
24
P2_47
P2_23
23
24
P2_24
P2_46
23
24
P2_48
25
26
P2_51
P2_25
25
26
P2_26
25
26
P2_52
P2_53
27
28
P2_55
P2_27
27
28
P2_28
P2_54
27
28
P2_56
P2_57
29
30
P2_59
P2_29
29
30
P2_30
P2_58
29
30
P2_60
P2_61
31
32
P2_31
31
32
P2_32
P2_62
31
32
P2_65
33
34
P2_67
P2_33
33
34
33
34
P2_68
P2_69
35
36
P2_71
P2_35
35
36
P2_36
P2_70
35
36
P2_72
P2_73
37
38
P2_75
P2_37
37
38
P2_38
P2_74
37
38
P2_76
39
40
P2_39
39
40
P2_40
39
40
P2_80
41
42
P2_41
41
42
P2_42
41
42
P2_84
43
44
P2_43
43
44
P2_44
43
44
45
46
P2_45
45
46
P2_46
45
46
P2_47
47
48
P2_48
49
50
P2_51
51
52
P2_52
P2_53
53
54
P2_54
P2_55
55
56
P2_56
P2_57
57
58
P2_58
P2_59
59
60
P2_60
P2_61
61
62
P2_62
DAI_P1_PDAP_HOLD
2
P2
1
MOSI
P2_85
DAI_P15_GP1
MISO
P2_83
IDC23X2
DAI_P1_PDAP_HOLD
3
64
65
66
P2_67
67
68
P2_68
P2_69
69
70
P2_70
P2_71
71
72
P2_72
P2_73
73
74
P2_74
P2_75
75
76
P2_76
77
78
79
80
81
82
P2_83
83
84
P2_84
P2_85
85
86
P2_86
87
88
89
90
MOSI
R1
10K
0805
DAI_P18_DIRCTRL
SCK
P2_86
2
DAI_P16_GP2
IDC23X2
DAI_P2_CLOCKIN
63
MISO
DAI_P2_CLOCKIN
FLAG1_SPI_CS
P2_65
DAI_P15_GP1
FLAG1_SPI_CS
DAI_P16_GP2
DAI_P18_DIRCTRL
3
P2_80
SCK
CON018
3.3V
C2
10UF
1210
ANALOG
DEVICES
C4
0.1UF
0805
4
Title
Size
Expanison Connector
P2
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP21262 EX-EXTENDER 1
EXPANSION CONNECTOR P2
Board No.
C
Date
20 Cotton Road
Rev
A0182-2003
2.0
Sheet
4-24-2006_9:28
D
3
of
7
A
B
C
D
EXPANSION INTERFACE (TYPE A)
3.3V
3.3V
1
3.3V
5V
5V
1
5V
P3_[1:90]
P3_[1:90]
P3_[1:90]
P3A
P3_1
1
2
P3_1
P3_5
3
4
P3_7
P3_9
5
6
P3_11
P3_13
7
8
P3_15
P3_17
9
10
P3_19
P3_21
P3_29
2
11
12
13
14
15
16
18
P3_35
P3_37
19
20
P3_39
P3_41
21
22
P3_45
23
24
P3_47
P3_49
25
26
P3_51
P3_53
27
28
P3_55
P3_57
29
30
P3_59
P3_69
32
34
P3_67
35
36
P3_71
P3_73
37
38
P3_75
P3_77
39
40
P3_79
41
42
P3_85
43
44
P3_89
45
46
P3_2
P3B
1
2
3
4
P3_6
3
4
P3_8
P3_5
5
6
P3_6
P3_10
5
6
P3_12
P3_7
7
8
P3_8
P3_14
7
8
P3_16
P3_9
9
10
P3_10
P3_18
9
10
P3_20
P3_11
11
12
P3_12
P3_22
11
12
P3_13
13
14
P3_14
13
14
P3_28
P3_15
15
16
P3_16
P3_30
15
16
P3_32
P3_17
17
18
P3_18
P3_34
17
18
P3_36
P3_19
19
20
P3_20
P3_38
19
20
P3_40
P3_21
21
22
P3_22
P3_42
21
22
P3_23
23
24
P3_46
23
24
P3_48
25
26
P3_50
25
26
P3_52
27
28
P3_28
P3_54
27
28
P3_56
P3_29
29
30
P3_30
P3_58
29
30
P3_60
P3_31
31
32
P3_32
P3_62
31
32
P3_64
P3_33
33
34
P3_34
33
34
P3_68
P3_35
35
36
P3_36
35
36
P3_72
P3_37
37
38
P3_38
37
38
P3_76
P3_39
39
40
P3_40
P3_78
39
40
P3_80
P3_41
41
42
P3_42
P3_82
41
42
P3_84
P3_86
43
44
P3_90
45
46
2
P3_63
33
P3_81
P3_2
P3_31
17
31
2
P3_23
P3_33
P3_61
P3
1
P3_70
EXP_CS1
P3_83
43
44
P3_45
45
46
P3_46
P3_47
47
48
P3_48
P3_49
49
50
P3_50
P3_51
51
52
P3_52
P3_53
53
54
P3_54
P3_55
55
56
P3_56
P3_57
57
58
P3_58
P3_59
59
60
P3_60
P3_61
61
62
P3_62
P3_63
63
64
P3_64
65
66
P3_67
67
68
P3_68
P3_69
69
70
P3_70
P3_71
71
72
P3_72
P3_73
73
74
P3_75
75
76
P3_76
P3_77
77
78
P3_78
P3_79
79
80
P3_80
P3_81
81
82
P3_82
P3_83
83
84
P3_84
P3_85
85
86
P3_86
87
88
89
90
IDC23X2
3
P3_89
IDC23X2
3
EXP_CS1
P3_90
CON018
3.3V
C13
10UF
1210
5V
C5
0.1UF
0805
C11
10UF
1210
C15
0.1UF
0805
ANALOG
DEVICES
4
Title
Expanison Connector
P3
Expanison Connector
P3
Size
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP21262 EX-EXTENDER 1
EXPANSION CONNECTOR P3
Board No.
C
Date
20 Cotton Road
Rev
A0182-2003
2.0
Sheet
4-24-2006_9:28
D
4
of
7
A
B
C
D
3.3V
Interface to ADC
Eval Board
1
R7
10K
0805
1
J1
2
1
4
3
AD0_C
47
6
5
AD1_C
46
8
7
AD2_C
44
10
9
AD3_C
43
12
11
AD4_C
41
14
13
AD5_C
40
16
15
AD6_C
38
18
17
AD7_C
37
20
19
AD8_C
22
21
AD9_C
U1
TX_CLK
2
1Y1
3
1Y2
5
1Y3
6
1Y4
8
2Y1
9
2Y2
11
2Y3
12
2Y4
1A1
1A2
1A3
1A4
2A1
2A2
2A3
2A4
36
23
3A2
AD10_C
33
26
25
3A3
AD11_C
32
28
27
3A4
AD12_C
30
30
29
4A1
AD13_C
29
32
31
4A2
AD14_C
27
34
33
4A3
AD15_C
26
2
36
35
38
37
40
39
4A4
DAI_P16_GP2_C
RX_CLK
AD1
AD2
AD3
AD4
AD5
AD6
AD7
13
3Y1
14
3Y2
16
3Y3
17
3Y4
19
4Y1
20
4Y2
22
4Y3
23
4Y4
3A1
35
24
AD0
AD8
AD9
AD10
AD11
AD12
AD13
AD14
AD15
1
OE1
EXP_CS1
DAI_P15_GP1_C
2
48
OE2
IDC20X2RASOC
25
OE3
24
OE4
SN74ALVTH16244
SSOP48
Place close to connector
R4
22
0805
U2
2
1B1
3
1B2
5
1B3
6
1B4
8
1B5
9
1B6
11
1B7
12
1B8
13
2B1
14
2B2
16
2B3
17
2B4
19
2B5
20
2B6
22
2B7
23
2B8
R3
22
0805
3
47
1A1
46
1A2
44
1A3
43
1A4
41
1A5
40
1A6
38
1A7
37
1A8
36
2A1
35
2A2
33
2A3
32
2A4
30
2A5
29
2A6
27
2A7
26
2A8
DAI_P16_GP2
3
DAI_P15_GP1
3.3V
R6
10K
0805
1
T/~R1
24
T/~R2
48
OE1
25
OE2
3.3V
R5
10K
0805
DIR_GP2
DIR_GP1
When T/~R is high the signals are transmitted from the EZ-KIT.
3.3V
74LVTH16245MEA
SSOP48
4
C7
0.1UF
0805
C8
0.1UF
0805
C9
0.1UF
0805
ANALOG
DEVICES
C18
0.1UF
0805
Title
74LVTH16245
Size
74LVTH16244
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP21262 EX-EXTENDER 1
HSC INTERFACE
Board No.
C
Date
20 Cotton Road
Rev
A0182-2003
2.0
Sheet
4-24-2006_9:28
D
5
of
7
A
B
C
D
3.3V
Label pin 1 = TXCLK
Label pin 2 = GND
Place close to each other
R18
33
0805
U7
1
OE/NC
OUT
1
To be used as test point
P4
2
5
CLOCK SHIFT CIRCUITRY
1
Place close to each other
IDC2X1
DNP
DIP8SOC
U4
R14
0
0805
DNP
1
R16
10K
0805
1
2
4
Direction/Clock Source Control
J3
SMA
CON043
2
4
1
2
12
U5
2
11
2
3
10
DIR_GP1
4
9
5
8
6
7
4
SN74LVC1G14DBVR
SOT23-5
3
IDC2X1
2
SW1
1
2
1
RX_CLK
P10
6
SJ1
3.3V
SHORTING
JUMPER
DAI_P18_DIRCTRL
R13
33
0805
4
DAI_P2_CLOCKIN
SN74LVC1G125
SOT23-5
DIP6
SWT017
DEFAULT=NOT INSTALLED
2
5
DIR_GP2
R9
51
1206
ON
R10
33
0805
U3
1
C3
0.1UF
0805
SN74LVC1G125
SOT23-5
DNP
Default Settings:
1 = ON, 2 = OFF, 3 = OFF, 4 = OFF, 5 = OFF, 6 = OFF
TX_CLK
1
CLOCK SQUARING CIRCUITRY
Install when using the SMA connector
as a clock source.
Be sure that the oscillator is not installed.
To be used as test point
P5
1
2
R17
1.2K
0805
R15
1.2K
0805
IDC2X1
DNP
R11
10K
0805
2
Label pin 1 = CLOCKIN
Label pin 2 = GND
3.3V
R8
10K
RES002
SPI
R12
10K
0805
Be sure that the pushbutton on the EZ-KIT Lite is not
driving FLAG1.
R2
10K
0805
J2
1
U6
2
FLAG1_SPI_CS
1A1
4
SCK
1A2
6
MOSI
1A3
3
8
1A4
11
MISO_IN
13
2A1
15
2A2
2A3
17
2A4
2
18
1Y1
16
1Y2
14
1Y3
12
1Y4
9
2Y1
7
2Y2
5
2Y3
3
2Y4
BCS_L
3
BSCK
4
BMOSI
5
P6
1
3
6
MISO_IN
7
2
MISO
8
IDC2X1
CON_RJ45
1
OE1
19
OE2
74LVX244M
SOIC20
SJ2
SHORTING
JUMPER
DEFAULT=NOT INSTALLED
3.3V
3.3V
C16
0.1UF
0805
3.3V
C10
0.1UF
0805
3.3V
C14
0.1UF
0805
3.3V
C12
0.1UF
0805
C6
0.1UF
0805
ANALOG
DEVICES
4
Title
SN74LVC1G125
SN74LVC1G125
SN74LVC1G125
OSC
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP21262 EX-EXTENDER 1
CONTROL - SPI INTERFACE
74LVX244M
Size
Board No.
C
Date
A
20 Cotton Road
B
C
Rev
A0182-2003
2.0
Sheet
4-24-2006_9:28
D
6
of
7
A
B
C
D
1
1
TP99
P17
1
2
TP108
P20
TP80
1
0805
2
TP5
2
TP21
1
2
2
TP43
TP103
1
TP110
2
TP69
2
1
0805
2
0805
P28
1
TP115
2
TP109
P29
1
TP118
TP102
TP112
P26
1
TP105
TP114
2
TP116
2
TP117
TP111
P30
1
TP120
2
TP113
P31
1
TP121
0805
P9
TP89
2
TP119
TP91
TP90
0805
P27
1
2
0805
0805
P23
TP104
TP107
0805
P25
1
0805
P19
1
2
0805
P22
0805
TP53
TP100
0805
P18
1
P24
1
0805
P21
TP101
0805
TP32
TP106
0805
P16
1
TP94
2
1
2
3
4
5
6
TP92
TP46
TP93
TP44
TP95
TP45
SOT23-6
TP122
P8
1
2
3
4
5
6
TP49
TP48
TP47
SOT23-6
0805
2
2
TP33
TP34
TP126
TP6
TP7
TP8
TP9
TP10
TP11
TP12
TP36
P13
TP13
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
P12
TP52
TP14
TP50
TP15
TP51
TP16
TP54
TP17
TP56
TP18
TP55
TP19
TP58
TP20
TP57
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
TP59
TP35
TP60
TP38
TP61
TP37
TP62
TP40
TP63
TP39
TP64
TP41
TP65
TP42
TP66
16
P15
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
TP22
TP68
TP23
TP86
TP24
TP84
TP25
TP85
TP26
TP82
TP27
TP83
TP28
TP79
TP29
TP81
TP30
TP88
TP31
TP87
SOIC20
P14
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
TP76
TP75
TP67
TP74
TP73
TP72
TP71
TP70
TP77
TP78
SOIC20
SOIC16
SOIC16
3
3
MH3
TP123
TP124
TP125
P33
1
2
3
SOT23D
TP97
TP96
TP98
MH2
MH1
P32
1
2
3
SOT23D
ANALOG
DEVICES
4
Title
Size
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP21262 EX-EXTENDER 1
BREADBOARD AREA FOOTPRINTS
Board No.
C
Date
20 Cotton Road
Rev
A0182-2003
2.0
Sheet
4-24-2006_9:28
D
7
of
7
I
INDEX
A
D
ADC (analog-to-digital converter) interface,
1-1, 2-2
address bus, 2-3
ADSP-21262 processors
clock in signal (DAI_PP2_CLOCKIN), 2-3,
2-4
MIS0 signal, 2-5
ADx pins, 1-2
architecture, of this EZ-Extender, 2-1
DAI_Px signals, 1-1, 2-3
data
bus, 1-2, 2-3
transfer (PDAP/HSC), 1-1
dimensions, of this EZ-Extender, -viii
DIP switch (SW1), 2-3
direction control switch (SW1), 2-3
B
bidirectional drivers, 2-1
bill of materials, A-1
block diagram, of this EZ-Extender, 2-1
board schematic, B-1
breadboard capabilities, -viii, 1-2
E
expansion interface, -vii, 1-2
external port, 1-2
F
features, of this EZ-Extender, -viii
G
C
clock, 2-2
disconnect jumper (P10), 2-5
signals, 2-2, 2-3, 2-4
source control switch (SW1), 2-3
sources, 2-5
compatible boards, of this EZ-Extender, 1-2
connectors
J2 (SPI), 2-5
J3 (SMA), 2-2, 2-5
customer support, -x
SHARC EZ-Extender Manual
general-purpose signals, 1-1, 2-2, 2-3
H
HSC (high-speed converter), -viii, 1-1, 2-2
I
interface, ADC and HSC, -viii, 1-1, 2-2
I-1
INDEX
J
R
jumpers, 2-3
clock disconnect (P10), 2-5
MISO disconnect (P6), 2-5
RJ-45 connector, -viii, 1-1
RX_CLK signal, 2-2, 2-4
S
M
oscillator, 2-3
schematic, of this EZ-Extender, B-1
serial peripheral interconnect (SPI)
connector (J2), 2-5
signals, -viii, 1-1
signal generator, 2-5
SMA connector (J3), 2-2, 2-5
surface-mounted (SMT) footprints, -viii, 1-2
SW1 (direction/clock source control) switch,
2-3
P
T
P10 (SMA connector clock disconnect) jumper,
2-5
P6 (MISO disconnect) jumper, 2-5
parallel data access port (PDAP), -viii, 1-1, 2-1,
2-3
transmit mode, 2-1
TX_CLK signal, 2-2, 2-4
MISO disconnect jumper (P6), 2-5
N
notation conventions, -xv
O
I-2
SHARC EZ-Extender Manual
Download PDF

advertising