Anritsu MD6430A Network Router User Manual

IP/NETWORK MEASURING INSTRUMENTS
NETWORK DATA ANALYZER
GPIB
OPTION
MD6430A
50 bit/s to 10 Mbit/s
One Instrument for Installation and Maintenance
3
The MD6430A Network Data Analyzer can measure errors on 13 different interfaces for leased lines (64 kbit/s to 6.3 Mbit/s), ISDN (BRI,
PRI), and V/X series interfaces, making it suitable for installation and
maintenance of a variety of networks.
Measurements include bit errors, alarms, delay time, frequency, digital level measurements, user pattern send/trace, etc., all of which
can be displayed on the large color LCD.
Error performance (ITU-T G.821, G.826, M.2100) is available with
various pseudorandom patterns and user patterns up to 1024 characters. Frame Relay measurement function, ISDN signaling function
(optional), and a simultaneous two-channel monitoring function are
also provided. Single button “quick” function and touch-screen ensure easy operation. This unit offers the user sophisticated functions
required for installation and maintenance in a small compact unit.
Features
• One unit supports installation and maintenance of leased lines,
ISDN, and frame relay
• Single button quick test operation
• Lightweight, with a battery-operated function
Applications
• Many applications ranging from low-speed modems to highspeed digital lines
The MD6430A can evaluate the quality of lines ranging from low-speed
modems to high-speed digital lines spanning 50 bit/s to 10 Mbit/s.
• Support for various interfaces
The MD6430A supports G.703 64k, I.430/I-430a 192k, G.703/G.704/
I.431 1.5M, 2M, 2M CMI, 6.3M, V.24/V.28, V.35, V.36, RS-449, X.20,
X.21, TTL/CMOS interfaces in a number of optional units designed
to meet customer needs.
Units
Interfaces
• Wide variety of measurement functions
Various measurements, such as error, alarm, clock slip, delay, frequency, and digital level can be performed. Also, can send user patterns with tracing functions.
• Frame relay measurements
Frame relay network connections (conforming to PVC and ITU-T
Q.933 Annex A) can be tested by the MD6430A. The user can also
monitor the congestion status such as FECN, BECN, and CLLM.
• Optional ISDN signaling functions (BRI, PRI)
The unit can be connected to ISDN networks so that both voice communication and error measurement can be performed.
• Error data analysis and storage functions
Error data can be collected in log or histogram format. This data can
also be stored in internal memory or on a floppy disk for later analysis.
• Touch-screen
The touch-screen, large color LCD, and pop-up menus provide a
much better GUI operating environment.
• Battery operation
When a commercial power supply is not available, the optional battery pack provides operation for up to 3 hours, and 5 hours in power
save operation.
• Full range of error measurement screens
Various measurement items can be displayed simultaneously for error
count, error rate, block error count, clock slip count, character error
count, error performance (G.821, G.826, M.2100), HDLC error (bad
frame, abort frame), and various types of alarms. The user can select
the desired items and can display them using the zoom function.
Uses
MU643000A
G.703 64k, I.430/I430-a 192k,
G.703/G.704/I.431 1.5M,
G.703/G.704/I.431 2.0M, 2M CMI,
G.703/G.704 6M
Europe and
Japan
MU643000B
G.703 64k, I.430/I430-a 192k,
G.703/G.704/I.431 1.5M, 2M CMI,
G.703/G.704 6M
Japan
MU643000C
G.703 64k, I.430/I430-a 192k,
G.703/G.704/I.431 2.0M
Europe
Note: All interface units support V.24/V.28, V.35, V.36, RS-449, X.20, X.21, and
TTL/CMOS.
http://www.anritsu.com
217
IP/NETWORK MEASURING INSTRUMENTS
• Supports frame relay measurements
• Supports ISDN networks (BRI, PRI)
Specific DLCI connections can be checked. PVC status checking
procedures are supported.
The unit can be connected to the ISDN public telephone network.
Return testing using one unit can be done by using the call loop function as below.
MD6430A
MD6430A
Call request
Data
Call
acceptance
Clear request
Data
Clear
confirmation
Frame relay measurement sequence
• Voice channel function
The CODEC function permits voice communications over a specified
channel. Simultaneous voice communications and measurements
are possible.
• Substantial analysis functions
Error status and alarm condition can be logged and displayed as histograms. The received data can also be captured.
• Easy operation
The touch-screen and pop-up menus are quick and user-friendly,
making operation easy for all levels of expertise.
http://www.anritsu.com
218
IP/NETWORK MEASURING INSTRUMENTS
Specifications
Interface
High speed: G.703 64k, I.430/I430-a 192k, G.703/G.704/I.431 1.5M∗1, ∗2, G.703/G.704/I.431 2.0M∗1, ∗3, 2M CMI∗1, ∗2,
G.703/G.704 6M∗1, ∗2 (2-wire simultaneous monitoring)
Low speed: V.24/V.28, V.35, V.36, RS-449, X.20, X.21, TTL/CMOS (Send/receive simultaneous monitoring)
Clock
(high-speed interface)
Internal clock: 64 kbit/s, 1.544 Mbit/s∗1, ∗2, 2.048 Mbit/s, 6.312 Mbit/s∗1, ∗2 (accuracy ≤±5 ppm)
External clock: 64k + 8k or slave sync to received data (slave oscillation range: ≤±100 ppm)
G.703 64k clock mode
Centralized clock, codirectional clock
Code law
(high-speed interface)
G.703 64k: AMI
I.430/I430-a 192k: AMI
G.703/G.704/I.431 1.5M: AMI/B8ZS∗1, ∗2
G.703/G.704/I.431 2.0M: AMI/HDB3∗1, ∗3
2M CMI: CMI
G.703/G.704 6M:B8ZS∗1, ∗2
3
Impedance
64k: 110 Ω/HIGH, 192k: 50/100 Ω/HIGH, 1.5M:100 Ω/HIGH, 2 M:75/120 Ω/HIGH, 2M CMI: 110 Ω/HIGH, 6M: 75 Ω/HIGH
Frames
(high-speed interface)
G.703/G.704/I.431 1.5M∗1, ∗2: 12MFP (G.704), 24MFP (G.704), 24MFP (NTT), unframe
G.703/G.704/I.431 2.0M∗1, ∗3: 16MFP (30B + D), 16MFP (31B), 2MFP (30B + D), 2MFP (31B), Unframe
2M CMI∗1, ∗2: PBX (TTC), CRV, ST (send only), unframe
G.703/G.704 6M∗1, ∗2: 4MFP (G.704), unframe
Data bit rate
(high-speed interface)
64k x n: 64 to 6272 kbit/s (n =1 to 98∗4 , sequential or mixed configuration may be selected.)
56k (1-7) x n: 56 to 5488 kbit/s (n =1 to 98∗4 )
56k (2-8) x n: 56 to 5488 kbit/s (n =1 to 98∗4 )
8k x n: 8, 16, 32 kbit/s
2.4k x n: 2.4 to 48 kbit/s (n = 1 to 20, sequential or mixed configuration may be selected for X.50 20 multiframe.)
0.6k x n: 0.6 to 48 kbit/s (n = 1 to 80, sequential or mixed configuration may be selected for X.50 80 multiframe.)
Others: Signaling, 1.544 Mbit/s
Send clock
(low-speed interface)
Internal clock
Sync (ST1): 50 bit/s to 10 Mbit/s (5 bit/s steps. However, V.24/V.28 and X.20 up to 200 kbit/s)
Async: 50, 75, 100, 110, 150, 200, 256, 300, 400, 500, 512, 600, 768, 800, 1k, 1.2k, 1.6k, 1.8k, 2k, 2.4k, 2.56k, 3k, 3.2k, 3.6k, 4.8k,
7.2k, 8k, 9.6k, 12k, 12.8k, 14.4k, 16k, 16.8k, 19.2k, 28.8k, 32k, 38.4k, 46k, 48k, 50k, 56k, 56.6k, 64k, 72k, 76.8k, 115.2k (bit/s)
Self oscillation accuracy: ≤±5 ppm
External clock (ST2, RTS): Frequency for each interface of 50 to10 Mbit/s (may be inverted.)
Receive clock
(low-speed interface)
External clock (ST, RTS): Frequency for each interface of 50 to 10 Mbit/s (May be inverted)
Internal clock (Async):
50, 75, 100, 110, 150, 200, 256, 300, 400, 500, 512, 600, 768, 800, 1k, 1.2k, 1.6k, 1.8k, 2k, 2.4k, 2.56k, 3k, 3.2k, 3.6k, 4.8k,
7.2k, 8k, 9.6k, 12k, 12.8k, 14.4k, 16k, 16.8k, 19.2k, 28.8k, 32k, 38.4k, 46k, 48k, 50k, 56k, 56.6k, 64k, 72k, 76.8k, 115.2k (bit/s)
Error measurement
pattern
Pseudorandom pattern: PRBS 6, 7, 9, 11, 15, 19, 20, 23, RPRBS 20 (reversed PRBS20), QRSS, positive/negative logic
Programmable pattern: 8 bit repetitive (start-stop sync: 5 to 8 bits)
Code pattern: 1:1, ALL 1, ALL 0
User pattern: 1 to 1024 characters (1 character steps), for character error measurement
Send pattern
User pattern: 1 to 128 kbyte
Error insertion
Error type: bit, bit + code, code
Insertion types
Single: 1 bit error inserted each time insert button pressed
Repeat: 1 bit error inserted each second
Cyclic: 2.5E-1 to 1.7E-7
Start-stop
synchronization
Start bit length: 1 bit
Stop bit length: 1, 1.5, 2 bits
Data length: 5, 6, 7, 8 bits
Parity: None, odd, even
Error/alarm measurement
Detected errors: Bit, code, parity, CRC, frame, character
Measurements:
Error count, error rate, block error count, block error rate, ES, EFS, clock slip, clock slip seconds, pattern sync loss count/time,
frame sync loss time, alarm time, signal loss time, AC power loss time
Error performance: G.821, G.826, M.2100
Measurement modes
Single: 1 s to 99 d 23 h 59 min 59 s
Repeat: 1 s to 99 d 23 h 59 min 59 s
Manual: 1 y max.
Measurement range
Error rate: 1.00E-15 to 1.00E00, Error count: 0 to 9.99E15
Pattern trace
Trace byte count: 1 Mbit max.
Trace start trigger: Manual, code detect
Trace stop trigger: Manual, code detect, code mismatch detect, trace byte count
Trigger detect delay: 0 to 8,000 bytes
Frequency measurement
Measurement range: DC to 10 MHz, Accuracy: ≤ (±5 ppm ±1 digit)
Delay time measurement
(Sync. mode only)
Measurement range: 0 to 16 s (0.001 ms steps)
Frame relay
measurement
Measurement items: Correct test packet count, lost test packet count, HDLC bad frame count, HDLC abort frame count
PVC connect confirmation test: To MD6430A or circuit loopback test (Conforms to ITU-T Q.933 Annex A)
DLCI: 16 to 991 (1 steps)
Test packet send interval time: 5 to 30 s (1 s steps)
Traffic congestion status monitoring: BECN, FECN, CLLM message detection (Conforms to ITU-T Q.922 Annex A)
Digital level measurement
Code law: A-law, µ-law
Measurement range: –60 to +3 dBm (0.1 dBm steps)
Send pattern: 0 dBm, 1 kHz pattern (Conforms to ITU-T G.711)
Continued on next page
http://www.anritsu.com
219
IP/NETWORK MEASURING INSTRUMENTS
ISDN calling/called function
INS64, INS1500 (Option: MU643000A/B-01), ETS1 ISDN (Option: MU643000A/C-02)
MUX/DEMUX
Able to drop/insert specified channels in high-speed interface through X.21 interface at 64k x n (n = 1 to 98)
Voice communication
Voice communication possible in any TS in high-speed interfaces (except G.703 64 kbit/s)
Error analysis
Displays sequential error/alarm measurement data and graphs
Signal monitor lamp
Indicates status of each signal line
External printer
Interface Centronics, D-sub 25-pin connector
External printer output
Enables printout of error measurement data
Measurement start time: Prints time and measurement conditions
During measurement: Prints specified error and alarm occurrence at each detected instance or at predefined time interval
Measurement stop time: Prints measured total results
Prints on screen contents
Display
Color TFT-LCD (8.4 inch)
Remote interface
RS-232C, D-sub 9-pin connector, GPIB (option)
Memory
3.5 inch FDD
Built-in timer
Year, month, day, hour, minute, second
Power supply
AC: 85 to 250 V, DC: Lithium ion battery (rechargeable, optional accessory), 50 VA
Battery operation time
3 h (max.) ∗5 h when using power save function
Operating temperature
0 to +50˚C, (FDD and at battery usage: +5 to +40˚C)
Dimensions and mass
290 (W) x 194 (H) x 94 (D) mm, ≤4.2 kg (excluding battery)
EMC
EN61326: 1997/A2: 2001 (Class A), EN61000-3-2: 2000 (Class A), EN61326: 1997/A2: 2001 (Annex A)
LVD
EN61010-1: 2001 (Pollution Degree 2)
∗1: Specification when using MU643000A Datacom Interface
∗2: Specification when using MU643000B Datacom Interface
∗3: Specification when using MU643000C Datacom Interface
∗4: Max. n value depends on interfaces
Ordering information
Please specify model/order number, name, and quantity when ordering.
Model/Order No.
MD6430A
Model/Order No.
Name
J0915A
Main frame
Network Data Analyzer
J0916A
Z0417
Z0403A
Standard accessories
AC adapter:
Power cord:
Touch pen (for touch panel):
Protective cover (protects display):
MD6430A operation manual (includes
MU643000A/B/C):
MD6430A remote control operation manual
(includes MU643000A/B/C):
MD6430A sample program (remote sample program):
Belt with hook (MD6430A carrying belt):
MD6430A-01
Option
GPIB
MU643000A
MU643000B
MU643000C
Units
Datacom Interface Unit (for Europe and Japan)
Datacom Interface Unit (for Japan)
Datacom Interface Unit (for Europe)
J0959B
J0844A
MU643000A-01
MU643000A-02
MU643000B-01
MU643000C-02
MU643000A-22
MU643000B-22
MU643000C-22
Options
JT-Q921/Q931 ISDN signaling
ETSI ISDN signaling
JT-Q921/Q931 ISDN signaling
ETSI ISDN signaling
CAS/FAS option (for Europe and Japan)
CAS/FAS option (for Japan)
CAS/FAS option (for Europe)
J0922B
Z0695
Z0406A
Z0402A
W1542AE
W1543AE
Z0619
B0441
B0442
B0443
A0006
J1026A
J0654A
J0661A
J0920B
J0913A
J0914A
1
1
1
1
pc
pc
pc
pc
1 copy
1 copy
1 pc
1 pc
Optional accessories
Lithium ion battery pack (battery pack for main frame)
Hard carrying case
Soft carrying case
Rack mount kit
Headset
GPIB cable (for MD6430A-01’s accessory), 2 m
Serial interface cross cable [D-Sub 9-pin (female) · D-Sub
9-pin (male)], 2 m (for remote control of main frame)
RS-232C straight cable [D-Sub 9-pin (female) · D-Sub
25-pin (male)], 2 m (for remote control of main frame)
Cross cable [D-Sub 9-pin (female) · D-Sub 25-pin (male)],
3 m (for remote control of main frame)
Measurement cable [D-Sub 25-pin (male) · half pitch
36-pin], 2 m (for V.24/V.28)
Measurement cable [V.35 connector (male) · half pitch
36-pin), 2 m (for V.35)
J0945
J0929
J0388B
J0390
J0392B
J0917A
J0923
J0463C
J0127B
J0939
J0921B
J0924B
J0930
J0960B
J0946A
J0946B
J0950
J0968
J0969C
J0925B
J0926B
J0927B
J0928B
Name
Measurement cable [D-Sub 37-pin (male) · half pitch
36-pin], 2 m (for V.36/RS-449)
Measurement cable [D-Sub 15-pin (male) · half pitch 36-pin],
2 m (for X.20/X.21, using B terminal as ST1 output type)
Measurement cable [D-Sub 15-pin (male) · half pitch 36-pin],
2 m (for X.20/X.21, using B terminal as ST2 input type)
Cross measurement cable [D-Sub 15-pin (male) · half
pitch 36-pin], 2 m (for X.20/X.21 MUX/DEMUX)
DCE/DTE conversion adapter (D-Sub 25-pin, for V.24/V.28)
DCE/DTE conversion adapter (D-Sub 34-pin, for V.35)
DCE/DTE conversion adapter (D-Sub 37-pin, for
V.36/RS-449)
TTL/CMOS connection box∗1 (I/O connector: BNC type)
Measurement cable (both-end Amphenol half pitch 36-pin),
1 m (for connection between MD6430A to TTL/CMOS)
Measurement cable [both-end 8-pin modular (RJ45) with
shield], 2 m (for 192k)
Measurement cable (RJ45 8-pin modular · clip), 2 m (for 192K)
ISO1073 cable [both-end 8-pin modular (ISO10173)], 2 m
(for 1.5M, 2M)
Coaxial cord (BNC-P · RG58A/U · BNC-P), 2 m (for 2M, 6M)
Coaxial cord (C-H3T type plug · BNC), 2 m (for 6M)
Measurement cable [8-pin modular (ISO10173) · M-1PS],
2 m (for 1.5M, 2M)
Measurement cable (mini-BANTAM · M-1PS), 2 m
(for 64k, 2M CMI)
Measurement cable (mini-BANTAM · I-214APS), 2 m (for
external input clock, 64k + 8k)
Measurement cable (mini-BANTAM · M-3912), 2 m (for
64k, Siemens type)
Measurement cable (mini-BANTAM · clip), 2 m (for 64k, 2M, CMI)
Measurement cable [8-pin modular (ISO10173) · M-3912],
1 m (for 1.5M/2M)
Measurement cable [8-pin modular (ISO10173) · M-3912],
2 m (for 1.5M/2M)
Measurement cable [8-pin modular (ISO10173) · clip],
2 m (for 1.5M/2M)
Balance cable (RJ45 · ISO10173), 2 m (for 192k)
Unbalance cable [SP3CP/3CV-P (BNC)], 2 m (for 6M)
Y cable (D-sub 25-pin · half pitch 36-pin/D-sub 25-pin),
2 m (for V.24/V.28 monitor)
Y cable (D-sub 25-pin · half pitch 36-pin/D-sub 25-pin),
2 m (for V.35 monitor)
Y cable (V.37 · half pitch 36-pin/D-sub 37), 2 m (for
V.36/RS-449 monitor)
Y cable (D-sub 15-pin · half pitch 36-pin/D-sub 15-pin),
2 m (for X.20/X.21 monitor)
∗1: Cable (J0923) required when using with TTL/CMOS interface
Note: For details of the measurement cable, refer to the Measurement Cable Selection Guide in the MD6430A Application Note.
http://www.anritsu.com
220
Download PDF

advertising