Operating instructions | AOC 203P Computer Monitor User Manual

41G2001-615-1A 英文
TABLE OF CONTENTS
FOR YOUR SAFETY -------------------------------------------------- 1
SAFETY PRECAUTIONS -------------------------------------- 2
SPECIAL NOTES ON LCD MONITORS ------------------- 3
BEFORE YOU OPERATE THE MONITOR --------------------FEATURES -------------------------------------------------------PACKING LIST --------------------------------------------------INSTALLATION INSTRUCTIONS --------------------------CONTROLS AND CONNECTORS -------------------------ADJUSTING THE VIEWING ANGLE -----------------------
3
3
3
4
5
6
OPERATING INSTRUCTIONS ------------------------------------- 7
GENERAL INSTRUCTIONS ---------------------------------- 7
HOW TO ADJUST A SETTING ------------------------------ 9
ADJUSTING THE PICTURE ------------------------------10-11
PLUG AND PLAY ----------------------------------------------- 12
TECHNICAL SUPPORT(FAQ) -------------------------------- 14-15
ERROR MESSAGE & POSSIBLE SOLUTION -------- 16
APPENDIX -------------------------------------------------------------- 16
SPECIFICATIONS ----------------------------------------- 16-17
PRESET DISPLAY MODES ------------------------------- 18
CONNECTOR PIN ASSIGNMENT ------------------------- 19
41G2001-615-1A 英文
1
Before operating the monitor, please read this manual thoroughly. This
manual should be retained for future reference.
FCC Class B Radio Frequency Interference Statement
WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
NOTICE:
1.
2.
3.
The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Shielded interface cables and AC power cord, if any, must be used in
order to comply with the emission limits.
The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modification to this equipment. It is the
responsibilities of the user to correct such interference.
WARNING:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture.
Dangerously high voltages are present inside the monitor. Do not open the
cabinet. Refer servicing to qualified personnel only.
SAFETY: Lamp Disposal
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE
RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR
FEDERAL LAWS. FOR MORE INFORMATION, CONTACT THE
ELECTRONIC INDUSTRIES ALLIANCE AT WWW.EIAE.ORG.
41G2001-615-1A 英文
2
PRECAUTIONS
z Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen
sink, laundry tub, swimming pool or in a wet basement.
z Do not place the monitor on an unstable cart, stand, or table. If the monitor
falls, it can injure a person and cause serious damage to the appliance.
Use only a cart or stand recommended by the manufacturer or sold with
the monitor. If you mount the monitor on a wall or shelf, use a mounting kit
approved by the manufacturer and follow the kit instructions.
z Slots and openings in the back and bottom of the cabinet are provided for
ventilation. To ensure reliable operation of the monitor and to protect it
from overheating, be sure these openings are not blocked or covered. Do
not place the monitor on a bed, sofa, rug, or similar surface. Do not place
the monitor near or over a radiator or heat register. Do not place the
monitor in a bookcase or cabinet unless proper ventilation is provided.
z The monitor should be operated only from the type of power source
indicated on the label. If you are not sure of the type of power supplied to
your home, consult your dealer or local power company.
z The monitor is equipped with a three-pronged grounded plug, a plug with a
third (grounding) pin. This plug will fit only into a grounded power outlet as
a safety feature. If your outlet does not accommodate the three-wire plug,
have an electrician install the correct outlet, or use an adapter to ground
the appliance safely. Do not defeat the safety purpose of the grounded
plug.
z Unplug the unit during a lightening storm or when it will not be used for
long period of time. This will protect the monitor from damage due to
power surges.
z Do not overload power strips and extension cords. Overloading can result
in fire or electric shock.
z Never push any object into the slot on the monitor cabinet. It could short
circuit parts causing a fire or electric shock. Never spill liquids on the
monitor.
z Do not attempt to service the monitor by yourself; opening or removing
covers can expose you to dangerous voltages and other hazards. Please
refer all servicing to qualified service personnel.
z To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked
between 100 - 240V AC, Min. 5A.
z The wall socket shall be installed near the equipment and shall be easily
accessible.
41G2001-615-1A 英文
3
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a
problem.
NOTES
• Due to the nature of the fluorescent light, the screen may flicker during
•
•
•
initial use. Turn off the Power Switch and then turn it on again to make
sure the flicker disappears.
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
The LCD panel used in this monitor is a very high technology product with
5,760,000 thin film transistors giving you fine picture details. Occasionally,
a few non-active pixels may appear on the screen as a fixed point of red,
green, blue, white or black. Please note that this does not indicate a
defective panel.
Due to the nature of the LCD screen, an afterimage of the previous screen
may remain after switching the image when the same image has been
displayed for a long time. The monitor will slowly recover from this.
BEFORE YOU OPERATE THE MONITOR
FEATURES
•
•
•
•
•
51cm(20”) TFT Color LCD Monitor
Crisp, Clear Display for Windows
Recommened Resolutions: 1600 X 1200 @60Hz
Ergonomic Design with Height, Pivot, Tilt & Swivel Adjustable Stand
Space Saving, Compact Case Design
CHECKING THE CONTENTS OF THE PACKAGE
The product package should include the following items:
1.
2.
3.
4.
5.
LCD Monitor
Owner's Manual
Power Cord
D-Sub Cable
DVI-D Cable
41G2001-615-1A 英文
4
INSTALLATION INSTRUCTIONS
SWIVEL BASE
Install
Figure 1
Remove
Installing and Removing the Swivel Base
POWERCORD
Power Source:
1. Make sure that the power cord is the correct type required in your area.
2. This LCD monitor has an External universal power supply that allows
operation in either 100/120V AC or 220/240V AC voltage area (No user
adjustment is required.)
3. Connect the power cord into your LCD monitor’s power input socket, and
then plug the other end into a 3-pin AC power outlet. The power cord may
be connected to either a wall power outlet or the power outlet socket on
your PC, depending on the type of power cord supplied with your LCD
monitor.
NOTES
A certified power supply cord has to be used with this equipment. The relevant
national installation and/or equipment regulations shall be considered. A
certified power supply cord not lighter than ordinary polyvinyl chloride flexible
cord according to IEC 60227 (designation H05VV-F 3G 0.75mm2 or
H05VVH2-F2 3G 0.75mm2) shall be used. Alternative a flexible cord be of
synthetic rubber according to IEC 60245 (designation H05RR-F 3G 0.75mm2)
shall be used.
41G2001-615-1A 英文
5
CONTROLS AND CONNECTORS
VIDEO CABLE
Connecting the signal Cable: Connect one end of the 15-pin D-Sub cable to
the back of the monitor and connect the other end to the computer’s D-Sub
port.
Connect one end of the 24-pin DVI cable to the back of the monitor and
connect the other end to the computer’s DVI port.
Connecting the Power Cord: Connect the power cord into your LCD
monitor’s power input socket, and then plug the other end into a 3-pin AC
power outlet. The power cord may be connected to either a wall power outlet
or the power outlet socket on your PC, depending on the type of power cord
supplied with your LCD monitor.
Caution: If the AC outlet is not grounded (with three holes), install the proper
grounding adapter (not supplied).
Figure 2
1.
2.
3.
Connecting Cables
D-Sub Cable
AC Power Cord
DVI Cable
41G2001-615-1A 英文
6
ADJUSTING THE VIEWING ANGLE
• For optimal viewing it is recommended to look at the full face of the
monitor, then adjust the monitor’s angle to your own preference.
• Hold the stand so you do not topple the monitor when you change the
monitor’s angle.
• You are able to adjust the monitor’s angle from -5° to 25°.
Figure 3
NOTES
• Do not touch the LCD screen when you change the angle. It may cause
damage or break the LCD screen.
• Careful attention is required not to catch your fingers or hands when you
change the angle.
41G2001-615-1A 英文
7
OPERATING INSTRUCTIONS
GENERAL INSTRUCTIONS
Press the power button to turn the monitor on or off. The other control buttons
are located on the front panel of the monitor (See Figure 4). By changing
these settings, the picture can be adjusted to your personal preferences.
• The power cord should be connected.
• Connect the video cable from the monitor to the video card.
• Press the power button to turn on the monitor position. The power indicator
will light up.
Figure 4
External Control Button
EXTERNAL CONTROLS
1.
2.
3.
4.
SOURCE
Auto Config / Exit
∧ / Brightness
∨ / Contrast
41G2001-615-1A 英文
5. Menu / Enter
6. Power Indicator
7. Power Button
8
FRONT PANEL CONTROL
• Power Button / Power Indicator:
Press this button to turn the monitor ON or OFF.
Blue
— Power On mode.
Orange — Off mode.
• MENU / ENTER :
Activate OSD menu when OSD is OFF or activate/de-activate adjustment
function when OSD is ON or Exit OSD menu when in Volume Adjust OSD
status.
• Auto Adjust button / Exit:
1.
2.
When OSD menu is in active status, this button will act as EXIT-KEY
(EXIT OSD menu).
When OSD menu is in off status, press this button for 2 seconds to
activate the Auto Adjustment function.
The Auto Adjustment function is used to set the HPos, VPos, Clock
and Focus.
OSD Lock Function: To lock the OSD, press and hold the MENU button
while the monitor is off and then press power button to turn the monitor
on. To un-lock the OSD - press and hold the MENU button while the
monitor is off and then press power button to turn the monitor on.
NOTES
• Do not install the monitor in a location near heat sources such as radiators
•
•
•
•
or air ducts, or in a place subject to direct sunlight, or excessive dust or
mechanical vibration or shock.
Save the original shipping carton and packing materials, as they will come
in handy if you ever have to ship your monitor.
For maximum protection, repackage your monitor as it was originally
packed at the factory.
To maintain the cleanness of your LCD display, wipe it periodically with
clean and soft cloth. The screen may be damaged by any liquid splash.
To keep the monitor looking new, periodically clean it with a soft cloth.
Stubborn stains may be removed with a cloth lightly dampened with a mild
detergent solution. Never use strong solvents such as thinner, benzene, or
abrasive cleaners, since these will damage the cabinet. As a safety
precaution, always unplug the monitor before cleaning it.
41G2001-615-1A 英文
9
HOW TO ADJUST A SETTING
1. Press the MENU-button to activate the OSD window.
2. Press < or > to navigate through the functions. Once the desired function
is highlighted, press the MENU-button to activate it. If the function
selected has a sub-menu, press < or > again to navigate through the submenu functions. Once the desired function is highlighted, press MENUbutton to activate it.
3. Press < or > to change the settings of the selected function.
4. To exit and save, select the exit function. If you want to adjust any other
function, repeat steps 2-3.
Figure 5
41G2001-615-1A 英文
The OSD Message
10
ADJUSTING THE PICTURE
The descriptions for function control LEDS
Main
Main Sub Menu
Sub
Menu Menu
Item
Menu
Item
Icon
Icon
Lumina
nce
Image
Setup
Contrast from Digital- Recall Cool
register.
Contrast Value
Brightness
Backlight Adjustment Recall Cool
Brightness
Value
Adjust Picture Phase Do Auto Config
to reduce HorizontalLine noise
Adjust picture Clock Do Auto Config
to reduce VerticalLine noise.
Adjust the horizontal Do Auto Config
position of the
picture.
Do Auto Config
Adjust the
verticalposition of the
picture.
The Color
Recall C1
Temperature
Temperature from
will be set to
EEPROM
Cool.
Recall C2
Temperature from
The User
EEPROM.
R/G/B
Recall sRGB
value(default is
Temperature from
100) will not be
EEPROM.
Modified by
Red Gain from
Reset function.
Digital-register.
Focus
H. Position
V. Position
Color
Temp.
C1
N/A
C2
N/A
sRGB
N/A
User
Green Gain Digitalregister.
Blue Gain from
Digital-register.
Analog
N/A
Select input signal
from analog source
(D-Sub)
Digital
N/A
Select input signal
from digital source
(DVI)
Input
Select
41G2001-615-1A 英文
Reset Value
Contrast
Clock
Image
Position
Description
11
OSD
Setup
H. Position
Adjust the horizontal 50
position of the OSD.
V. Position
50
Adjust the
verticalposition of the
OSD.
Adjust the OSD
10
timeout.
OSD
Timeout
Langua
ge
Informat
ion
Reset
Exit
41G2001-615-1A 英文
English
N/A
Deutsch
N/A
Français
N/A
Español
N/A
Italiano
N/A
简体中文
N/A
Information
N/A
Yes
N/A
No
N/A
N/A
N/A
Set OSD display
language to English.
Set OSD display
language to German.
Set OSD display
language to French.
Set OSD display
language to Spain.
Set OSD display
language to Italian.
Set OSD display
language to
Simplified Chinese.
Show the resolution,
H/V frequency and
input port of current
iput timing.
Clear each old status
of Auto-configuration
and set the color
temperature to Cool.
Do not execute reset,
return to main menu.
Exit OSD
12
The Language
will be set to
English.
N/A
N/A
N/A
N/A
PLUG AND PLAY
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the
VESA DDC STANDARD. It allows the monitor to inform the host system of its
identity and, depending on the level of DDC used, communicate additional
information about its display capabilities.
The DDC2B is a bidirectional data channel based on the I²C protocol. The
host can request EDID information over the DDC2B channel.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS
NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE
PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL.
This monitor meets the Green monitor standards as set by the Video
Electronics Standards Association (VESA) and The Swedish Confederation
Employees (NUTEK). This feature is designed to conserve electrical energy
by reducing power consumption when there is no video-input signal present.
When there is no video input signal this monitor, following a time-out period,
will automatically switch to an OFF mode. This reduces the monitor's internal
power supply consumption. After the video input signal is restored, full power
is restored and the display is automatically redrawn. The appearance is similar
to a "Screen Saver" feature except the display is completely off. The display is
restored by pressing a key on the keyboard, or clicking the mouse.
USING THE RIGHT POWER CORD :
The accessory power cord for the Northern American region is the wallet plug
with NEMA 5-15 style and is UL listed and CSA labeled. The voltage rating for
the power cord shall be 125 volts AC.
Supplied with units intended for connection to power outlet of personal
computer: Please use a cord set consisting of a minimum No. 18 AWG, type
SJT or SVT three conductors flexible cord. One end terminates with a
grounding type attachment plug, rated 10A, 250V, CEE-22 male configuration.
The other end terminates with a molded-on type connector body, rated 10A,
250V, having standard CEE-22 female configuration.
Please note that power supply cord needs to use VDE 0602, 0625, 0821
approval power cord in European counties.
41G2001-615-1A 英文
13
TECHNICAL SUPPORT (FAQ)
Problem & Question
Power LED is not on
No Plug & Play
Picture is fuzzy
Picture bounces or a wave
pattern is present in the picture
The power LED is ON but
there’s no video or no picture.
Missing one of the primary
colors (RED, GREEN, or
BLUE)
41G2001-615-1A 英文
Possible Solution
*Check if the Power Switch is in the ON
position
*Power Cord should be connected
*Check if the PC system is Plug & Play
compatible
*Check if the Video Card is Plug & Play
compatible
*Check if the D-15 plug pin of Video
Cable is bent
*Make sure the LCD Monitor Drivers are
installed
*Adjust the Contrast and Brightness
Controls.
*Move electrical devices that may cause
electrical interference.
*Computer Power Switch should be in
the ON position.
*Computer Video Card should be snugly
seated in its slot.
*Make sure monitor’s video cable is
properly connected to the computer.
*Inspect monitor’s video cable and make
sure none of the pins are bent.
*Make sure computer is operational by
hitting the CAPS LOCK key on the
keyboard while observing the CAPS
LOCK LED. The LED should either turn
ON or OFF after hitting the CAPS
LOCK key.
*Inspect the monitor’s video cable and
make sure that none of the pins are
bent.
14
Screen image is not centered or *Adjust pixel frequency (CLOCK) and
sized properly.
FOCUS or press hot-key (AUTO).
Picture has color defects
*Adjust RGB color or select color
(white does not look white)
temperature.
Horizontal
or
vertical *Use win 95/98 shut-down mode Adjust
disturbances on the screen
CLOCK and FOCUS or perform hot- key
(AUTO-key).
CLOCK (pixel frequency) controls the number of pixels scanned by one
horizontal sweep. If the frequency is not correct, the screen shows vertical
stripes and the picture has not correct width.
FOCUS adjusts the phase of the pixel clock signal. With a wrong phase
adjustment the picture has horizontal disturbances in light picture.
For FOCUS and CLOCK adjustment use “dot-pattern” or win 95/98 shut-down
mode pattern.
41G2001-615-1A 英文
15
ERROR MESSAGE & POSSIBLE SOLUTION
CABLE NOT CONNECTED :
1.
Check that the signal-cable is properly connected , If the connector is
loose, tighten the connector’s screws.
2.
Check the signal-cable’s connection pins for damage.
INPUT NOT SUPPORTED :
Your computer has been set to unsuitable display mode ,set the computer to
display mode given in the following table (See page 19).
41G2001-615-1A 英文
16
APPENDIX
SPECIFICATIONS
Driving system TFT Color LCD
LCD Panel
Size
51cm(20")
Pixel pitch
0.255mm( H )x 0.255mm( V )
Viewable angle 170° (H) 170° (V)
Video
R,G,B Analog Interface
Digital interface
H-Frequency
30KHz – 80Hz
V-Frequency
55-75Hz
Display Colors
16.7M Colors
Dot Clock
162 MHz
Max. Resolution
1600 x 1200 @ 60Hz
Plug & Play
VESA DDC1/2BTM
Power Consumption
ON Mode
OFF Mode
≤55
W
≤2W
Input Connector
D-Sub 15pin
DVI 24pin
Input Video Signal
Analog:0.7Vp-p(standard),
75 OHM, Positive
Digital sigal
Maximum Screen Size
Horizontal : 376.32mm
Vertical : 301.056mm
Power Source
100~240VAC,47~63HZ
Environmental
Considerations
Operating Temp: 0° to 35°C
Storage Temp.: -20° to 60°C
Operating Humidity: 10% to 85%
Dimensions
445.6(W)×417.6(H)×245.6(D)mm
Weight (N. W.)
7.5kg Unit (net)
41G2001-615-1A 英文
17
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Switch
External Controls:
Power Button
Contrast
Brightness
Focus
Clock
H.Position
V.Position
(C1) Color
(C2)Color
SRGB Color temperature
User
Input signal Selection
OSD position, OSD timeout
Language
Display information
Reset
Exit
55 Watts
cULus, FCC, CE, ISO13406-2
Functions
Power Consumption
( Maximum )
Regulatory Compliance
41G2001-615-1A 英文
Source
Auto Config / Exit
∧ / Brightness
∨ / Contrast
Menu / Enter
18
Preset Display Modes
STANDARD
IBM
DOS
VGA
RESOLUTION
HORIZONTAL
FREQUENCY(KHZ)
VERTICAL
FREQUENCY(HZ)
720 × 400
31.47
70.0
640 × 480
31.47
60.0
640 × 480
37.50
75.0
800 × 600
37.879
60.0
800 × 600
46.875
75.00
1024 × 768
48.363
60.0
1024 × 768
56.476
70.0
1024 x 768
60.02
75.0
1024 x 768
48.780
60.0
1024 x 768
60.241
75.0
1280 × 1024
64.00
60.0
1280 × 1024
80.00
75.0
1600 x 1200
75.00
60.0
SVGA
VESA
XGA
SXGA
UXGA
41G2001-615-1A 英文
19
CONNECTOR PIN ASSIGNMENT
1
5
6
10
11
15
15 - Pin Color Display Signal Cable
PIN NO.
1.
2.
3.
4.
`
6.
7.
8.
DESCRIPTION
PI N NO.
DESCRIPTION
9.
10.
11.
12.
13.
14.
15.
+5V
Detect Cable
NC
DDC-Serial data
H-sync
V-sync
DDC-Serial clock
Video-Red
Video-Green
Video-Blue
NC
Ground
GND-R
GND-G
GND-B
24 - Pin Color Display Signal Cable
PIN NO.
DESCRIPTION
PI N NO.
1.
2.
3.
TMDS Data 2TMDS Data 2+
TMDS Data 2/4
Shield
TMDS Data 4TMDS Data 4+
DDC Clock
DDC Data
13.
14.
15.
TMDS Data 3+
+5V Power
Ground(for+5V)
16.
17.
18.
19.
NC
TMDS Data 1TMDS Data 1+
TMDS Data 1/3
Shield
TMDS Data 3-
20.
21.
22.
23.
Hot Plug Detect
TMDS Data 0TMDS Data 0+
TMDS Data 0/5
Shield
TMDS Data 5TMDS Data 5+
TMDS Clock Shield
TMDS Clock +
24.
TMDS Clock -
4.
5.
6.
7.
8.
9.
10.
11.
12.
41G2001-615-1A 英文
20
DESCRIPTION
41G2001-615-1A 英文
21
Download PDF

advertising