AOC 916SWA Computer Monitor User Manual

916Swa User Manual
q
1. Preface
About This Guide
This guide describes the monitor's features, setup, and operation. lnformation in this document is subject to change without notice.
The sections are as follows:
•
•
•
•
•
•
•
Safety Instructions: lists safety information.
Setup: describes the initial setup process.
Using the Monitor: gives an overview of how to use the monitor.
Drivers: provides driver installation instructions for Windows.
Technical Support : provides tips and solutions for common problems.
Product Information: lists the technical specifications of the monitor.
Warranty Statement: Warranty Statement used in Europe.
National Conventions
The following subsections describe notational conventions used in this document.
Notes, Cautions, and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are
used as follows:
NOTE: A NOTE indicates important information that helps you make better use of your computer system.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem.
Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific presentation of the warning is mandated by regulatory
authority.
Product Registration
Please link www.aoc.com, select your country or region, log in Product Registration to register .
2. Safety Introduction
FCC Notice
FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1.
2.
3.
4.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
NOTICE :
1.
2.
3.
The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is theresponsibilities of the user to
correct such interference.
WEEE Declaration
Disposal of Waste Equipment by Users in Private Household in the European Union.
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste.Instead, it is your responsibility to
dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.The separate collection
and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health
and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste
disposal service or the shop where you purchased the product .
HG Declaration
SAFETY: Lamp Disposal
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. FOR
MORE INFORMATION, CONTACT THE ELECTRONIC INDUSTRIES ALLIANCE AT WWW.EIAE.ORG.
Precautions
WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards,
and/or mechanical hazards.
Read and follow these precautions when connecting and using your computer monitor:
PRECAUTIONS
•
•
•
•
•
•
•
•
•
•
•
•
Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement.
Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart
or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer
and follow the kit instructions.
Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable operation of the monitor and to protect it from overheating,
be sure these openings are not blocked or covered. Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or over a
radiator or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided.
The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult
your dealer or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety
feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do
not defeat the safety purpose of the grounded plug.
Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric shock. Never spill liquids on the monitor.
Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous voltages and other hazards. Please refer all servicing to
qualified service personnel.
To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100 - 240V AC,
Min. 5A.
The wall socket shall be installed near the equipment and shall be easily accessible.
For use only with the attached power adapter (Output 12Vdc) which have UL,CSA listed license(Only for monitors with power adapter).
3. Setup
Setup the stand and base
Please setup or remove the base following below steps.
Adjusting Viewing Angle
•
•
•
For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference.
Hold the stand so you do not topple the monitor when you change the monitor's angle.
You are able to adjust the monitor's angle from -5°to 20°.
NOTE:
Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.
Attaching the Cables
Cable Connections On Back of Monitor and Computer
1.Power
2.Analog
3. audio
Turn off your computer before performing the procedure below.
1.
2.
3.
Connect the power cable to the AC port on the back of the monitor.
Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port.
Turn on your monitor and computer.
If your monitor displays an image, installation is complete. If it does not display an image, see Troubleshooting.
Attaching Wall Mounting Arm
Preparing to Install An Optional Wall Mounting Arm
4. Using the Monitor
Setting the Optimal Resolution
The recommended resolution for this monitor is 1440 by 900. To setup the monitor to this resolution, follow the steps below.
1.
2.
3.
4.
5.
6.
Click START.
Click SETTINGS.
Click CONTROL PANEL.
Double click DISPLAY.
Click SETTINGS.
Set the resolution SLIDE-BAR to 1440 by 900.
External Controls
Press the power button to turn the monitor on or off. The other control knobs are located at front panel of the monitor (See Figure ). By changing these settings, the picture
can be adjusted to your personal preferences.
* The power cord should be connected.
* Press the power button to turn on the monitor. The power indicator will light up.
1. Auto Config
2. Volume / 3. Volume / +
4. Menu / Enter
5. Power Button & Indicator
OSD Settings
•
•
•
•
•
Press the MENU-button to activate the OSD window.
Press+ or - to navigate through the functions. Once the desired function is highlighted, press the MENU-buttonto activate it.If the function selected has a sub-menu,
press or again to navigate through the sub-menu functions.Once the desired function is highlighted, press MENU-button to activate it.
Press+ or - to change the settings of the selected function. To exit and save, select the exit function. If you want to adjust any other function, repeat steps 2-3.
OSD Lock Function: To lock the OSD, press and hold the MENUbutton while the monitor is off and then press power button to turn the monitor on. To un-lock the
OSD - press and hold the MENUbutton while the monitor is off and then press power button to turn the monitor on.
Press Exit key continually for 7 sec. to turn on or off DDC-CI.
DCB Adjustment
What is DCB?
Dynamic Color Boost (DCB) is an advanced color adjustment technology. Through analyzing RGB signals, DCB creates more vivid and natural images to suit various color
environment needs. DCB has two types of color enhancers: “Color Boost” and “Picture Boost” .
DDC: Dynamic color control
ICM: Intelligent color management
1) How to use Color Boost?
YCM adjustment: In addition to the basic R (red), G (green), B (blue) color adjustments, Color Boost has added Y (yellow), B (blue), and M (magenta) for more color finetuning options. YCM adjustments are in the third icon labeled "Color Temperature "in the OSD menu. When adjusting YCM values, RBG values will also be changed
automatically due to the color correlation between RGB and YCM.
Five color-enhancement settings: To accommodate various display needs, Color Boost also offers 5 different color enhancement modes: Full Enhance, Natural Skin,
Green Field, Sky Blue, and Auto-Detect. Please go to the fourth icon labeled “Color Boost” in the OSD menu and select one of the five settings you desire to be turned on.
Full Enhance: When "Full Enhance" is turned on, the color saturation of the entire screen is fully enriched, thus all colors become more vibrant.
Nature Skin: When "Natural Skin" is turned on, the red and yellow colors are enriched automatically, thus presents human skin with more natural and truer colors.
"Natural Skin" setting is ideal for viewing human portrait and detailed skin texture.
Green Field: When "Green Field" is turned on, the green color is enriched so that football field and mountain landscape would look more natural and fresh. “Green Field”
setting is ideal for watching mountain scenery and outdoor sports.
Sky Blue: When"Sky Blue" is turned on, the color blue is being fine-tuned so that the sky or ocean landscape will look more vivid and in-depth. "Sky Blue" setting is ideal
for viewing sky and ocean images.
Auto Detect:
When “Auto Detect” is turned on, every pigment will be detected and self-adjusted to render a lively picture.
Demo:
Screen divided into two for demonstration purposes.
2) How to use Picture Boost?
Users can change the color settings of a self-selected zone on the screen. The size and position of the selected zone can also be adjusted. "Picture Boost" is located in the
fifth icon labeled "Picture Boost" in the OSD menu. Turn on "Bright Frame" to select a zone on the screen to be enhanced. Please note when adjust or turn on any one of
the DCB features, the rest of color settings including DCR will be disabled or return to default.
Disclaimer: DCB aftereffects are subject to the resolution and quality of the display content, hence may look different than the above illustrations.
DCR Adjustment
What is DCR?
Dynamic Contrast Ratio (DCR) auto adjusts the brightness of the screen so users can see the darker areas of the displayed content in more depths. By increasing the
darkness of the dark areas and the brightness of the bright areas, contrast ratio is uplifted to exceed 2000:1. DCR value varies subject to the original CR values of the LCD
module. The higher the original CR, the higher DCR can be achieved. DCR is great for watching movie or video contents.
How to Use DCR?
Go to the first OSD icon labeled "Luminance", turn on or off DCR as desires. DCR boosts the contrasts between lightness & darkness and enables the viewer to see more
layers and details of the picture, especially in the darker areas. Please note when DCR is on, DCB will be disabled.
DCR Demos:
Disclaimer: DCR aftereffects are subject to the resolution and quality of the display content, hence may look different than the above illustrations.
Function Control Illustration
Luminance
Brightness
Contrast
Eco mode
Gamma
DCR
Image Setup
Clock
Focus
H.Position
V.Position
Color Temp.
Warm
Normal
Cool
sRGB
User
Adjust Range
0-100
0-100
Standard
Text
Internet
Game
Movie
Sports
Gamma1
Gamma2
Gamma3
Off
On
Description
Backlight Adjustment
Contrast from Digital-register.
Standard Mode
Text Mode
Internet Mode
Game Mode
Movie Mode
Sports Mode
Adjust to Gamma1
Adjust to Gamma 2
Adjust to Gamma 3
Disable dynamic contrast ratio
Enable dynamic contrast ratio
0-100
0-100
0-100
0-100
Adjust picture Clock to reduce Vertical-Line noise.
Adjust Picture Phase to reduce Horizontal-Line noise
Adjust the verticalposition of the picture.
Adjust the horizontal position of the picture.
User-B
Recall Warm Color Temperature from EEPROM.
Recall Normal Color Temperature from EEPROM.
Recall Cool Color Temperature from EEPROM.
Recall SRGB Color Temperature from EEPROM.
Blue Gain from Digital-register
Color Boost
Full Enhance
Nature Skin
Green Field
Sky-blue
AutoDetect
Demo
Picture Boost
Frame Size
Brightness
Contrast
Hue
Saturation
Position
Bright Frame
OSD Setup
H.Position
V.Position
Timeout
Language
Extra
Auto Config
Reset
EXIT/DDC-CI
Information
User-G
User-R
User-Y
User-C
User-M
Green Gain Digital-register.
Red Gain from Digital-register
Yellow Gain from Digital-register
Cyan Gain from Digital-register
Magenta Gain from Digital-register
on or off
on or off
on or off
on or off
on or off
on or off
Disable or Enable Full Enhance Mode
Disable or Enable Nature Skin Mode
Disable or Enable Green Field Mode
Disable or Enable Sky-blue Mode
Disable or Enable AutoDetect Mode
Disable or Enable Demo
0-14
0-100
0-100
0-100
0-100
H. position
V.position
on or off
Adjust Frame Size
Adjust Frame Brightness
Adjust Frame Contrast
Adjust Frame Hue
Adjust Frame Saturation
Adjust Frame horizontal Position
Adjust Frame vertical Position
Disable or Enable Bright Frame
0-100
0-100
0-100
Adjust the verticalposition of OSD
Adjust the horizontal position of OSD
Adjust the OSD Timeout
Select the OSD language
yes or no
yes or no
Auto adjust the picture to default
Reset the menu to default
Turn ON/OFF DDC-CI Support
Show the information of the main image and sub-image source
LED Indicators
Status
LED Color
Full Power Mode
Active-off Mode
Green
Orange
This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this procedure. Follow these steps:
1.
2.
3.
Remove the base.
Follow the manufacturer's instructions to assemble the wall mounting arm.
Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor.
4.
5.
Insert the 4 screws into the holes and tighten.
Reconnect the cables. Refer to the user's manual that came with the optional wall mounting arm for instructions on attaching it to the wall.
5. Drivers
Windows 2000
1. Start Windows® 2000
2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.
3. Double click on the 'Display' Icon.
4. Select the 'Settings' tab then click on 'Advanced...'.
5. Select 'Monitor'
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation.
- If the 'Properties' button is active. Click on 'Properties' button. Please follow the steps given below.
6. Click on 'Driver' and then click on 'Update Driver...' then click on the 'Next' button.
7. Select 'Display a list of the known drivers for this device so that I can choose a specific driver', then click on 'Next' and then click on 'Have disk...'.
8. Click on the 'Browse...' button then select the appropriate drive F: ( CD-ROM Drive).
9. Click on the 'Open' button, then click on the 'OK' button.
10. Select your monitor model and click on the 'Next' button.
11. Click on the 'Finish' button then the 'Close' button.
If you can see the 'Digital Signature Not Found' window, click on the 'Yes' button.
Windows ME
1. Start Windows® Me
2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.
3. Double click on the 'Display' Icon.
4. Select the 'Settings' tab then click on 'Advanced...'.
5. Select the 'Monitor' button, then click on 'Change...' button.
6. Select 'Specify the location of the driver(Advanced)' and click on the 'Next' button.
7. Select 'Display a list of all the drivers in a specific location, so you can choose the driver you want', then click on 'Next' and then click on 'Have Disk...'.
8. Click on the 'Browse...' button, select the appropriate drive F: ( CD-ROM Drive) then click on the 'OK' button.
9. Click on the 'OK' button, select your monitor model and click on the 'Next' button.
10. Click on 'Finish' button then the 'Close' button.
Windows XP
1. Start Windows® XP
2. Click on the 'Start' button and then click on 'Control Panel'.
3. Select and click on the category 'Printers and Other Hardware'
4. Click on the 'Display' Item.
5. Select the 'Settings' tab then click on the 'Advanced' button.
6. Select 'Monitor' tab
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation.
- If the 'Properties' button is active, click on 'Properties' button.
Please follow the steps below.
7. Click on the 'Driver' tab and then click on 'Update Driver...' button.
8. Select the 'Install from a list or specific location [advanced]' radio button and then click on the 'Next' button.
9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the 'Next' button.
10. Click on the 'Have disk...' button, then click on the 'Browse...' button and then select the appropriate drive F: (CD-ROM Drive).
11. Click on the 'Open' button, then click the 'OK' button.
12. Select your monitor model and click on the 'Next' button.
- If you can see the 'has not passed Windows® Logo testing to verify its compatibility with Windows® XP' message, please click on the 'Continue Anyway' button.
13. Click on the 'Finish' button then the 'Close' button.
14. Click on the 'OK' button and then the 'OK' button again to close the Display_Properties dialog box.
Windows Vista
1. Start Windows® Vista
2. Click the Start button; select and click on 'Control Panel'.
3. Select and click on 'Hardware and Sound'
4. Choose 'Device Manager' and Click on 'Update device drivers'.
5. Select 'Monitor' and then right click on 'Generic PnP Monitor'.
6. Click on 'Update Driver Software'.
7. Select 'Browse my computer for driver software'.
8. Click the 'Browse'button and choose the drive in which you've placed the disk. Example:(CD-ROM Drive:\\Lcd\PC\drivers\).
9. Click the 'Next' button.
10. Wait few minutes for installing the driver, and then click 'Close' button.
6. Technical Support
Frequently Asked Questions
Problem & Question
•
Power LED Is Not ON
•
No Plug & Play
Picture Is Fuzzy & Has Ghosting Shadowing
Problem
Picture Bounces, Flickers Or Wave Pattern Is
Present In The Picture
Monitor Is Stuck In Active Off-Mode"
•
Possible Solutions
Make sure the power button is ON and the Power Cord is properly connected to a grounded power outlet
and to the monitor.
In order for the Plug & Play feature of the monitor to work, you need a Plug & Play compatible computer
& video card. Check with your computer manufacturer. Also check the monitor's video cable and make
sure none of the pins are bent.
Make sure the AOC Monitor Drivers are installed (AOC Monitor Drivers are available at :
http://www.aoc.com)
•
•
Adjust the Contrast and Brightness Controls.
Make sure you are not using an extension cable or switch box. We recommend plugging the monitor
directly to the video card output connector on the back of your computer.
•
•
Move electrical devices that may cause electrical interference as far away from the monitor as possible.
Use the maximum refresh rate your monitor is capable of at the resolution your are using.
•
•
•
•
•
The Computer Power Switch should be in the ON position.
The Computer Video Card should be snugly seated in its slot.
Make sure the monitor's video cable is properly connected to the computer.
Inspect the monitor's video cable and make sure none of the pins are bent.
Make sure your computer is operational by hitting the CAPS LOCK key on the keyboard while observing
the CAPS LOCK LED. The LED should either turn ON or OFF after hitting the CAPS LOCK key.
•
•
Inspect the monitor's video cable and make sure that none of the pins arebent.
Make sure the monitor's video cable is properly connected to the computer.
Screen image is not centered or sized
properly
•
Adjust H-Position and V-Position or press hot-key (AUTO).
Picture has color defects (white does not
look white)
•
Adjust RGB color or select color temperature
Horizontal or vertical disturbances on the
screen
•
Use win 95/98 shut-down mode Adjust CLOCK and FOCUS or perform hot-key (AUTO-key )
Missing one of the primary colors (RED,
GREEN, or BLUE)
7. Product Information
Specifications
Model number
916Swa
Driving system
TFT Color LCD
Size
48.0cm ( 19" 16:10)
Pixel pitch
0.285mm(H) x 0.285mm(V)
LCD Panel
Video
R, G, B Analog lnterface
Separate Sync.
H/V TTL
Display Color
16.2 million Colors
Dot Clock
135 MHz
Horizontal scan range
31 kHz - 80 KHz
Horizontal scan
410.4mm
Size(Maximum)
Vertical scan range
55 Hz - 75 Hz
Vertical scan Size(Maximum) 256.5mm
Optimal preset resolution
1440 x 900 (60 Hz)
Resolution
Highest preset resolution
1440 x 900 (75 Hz)
Plug & Play
VESA DDC2B/CI
Input Connector
D-Sub 15pin
Input Video Signal
Analog: 0.7Vp-p(standard), 75 OHM, Positive
Power Source
100~240VAC, 47~63Hz
Active < 37W
Power Consumption
Standby < 2W
Connector Type
15-pin Mini D-Sub
Signal Cable Type
Detachable
Dimensions & Weight:
Height (with base)
362.9 mm
Physical Characteristics
Width
438.5 mm
Depth
209.86 mm
Weight (monitor only)
4.4 kg
Weight (with packaging)
5.8 kg
Environmental
Temperature:
Operating
Non-Operating
Humidity:
Operating
Non-Operating
Altitude:
Operating
Non-Operating
0° to 50°
-20°to 60°
10% to 85% (non-condensing)
5% to 80% (non-condensing)
0~ 3000m (0~ 10000 ft )
0~ 5000m (0~ 15000 ft )
EPA Energy STAR ®
ENERGY STAR® is a U.S. registered mark. As an ENERGY STAR® Partner, AOC International (Europe) GmbH has determined that this product meets the ENERGY
STAR® guidelines for energy efficiency.
Preset Display Modes
HORIZONTAL
VERTICAL
VGA
640 X 480
FREQUENCY(kHZ)
35.0kHz
FREQUENCY(Hz)
66.7Hz
VGA
SVGA
832 X 624
49.7kHz
74.5Hz
1152 X 870
68.7kHz
75.0Hz
Dos-mode
640 X 350
31.5kHz
70.1Hz
Dos-mode
720 X 400
31.5kHz
70.1Hz
VGA
640 X 480
31.5kHz
60.0Hz
VGA
640 X 480
37.9kHz
72.8Hz
VGA
SVGA
640 X 480
37.5kHz
75.0Hz
800 X 600
35.2kHz
56.3Hz
SVGA
800 X 600
37.9kHz
60.3Hz
SVGA
800 X 600
48.1kHz
72.2Hz
SVGA
800 X 600
46.9kHz
75.0Hz
XGA
1024 X 768
48.4kHz
60.0Hz
XGA
1024 X 768
56.5kHz
70.1Hz
Normal
1024 X 768
60.0kHz
75.0Hz
Special
1152 X 864
67.5kHz
75.0Hz
XGA
1024 X 768
57.7kHz
72.0Hz
STAND
RESOLUTION
XGA
1024 X 768
60.023kHz
75.0Hz
SXGA
1280 X 1024
64.0kHz
60.0Hz
SXGA
1280 X 1024
74.4kHz
70.0Hz
SXGA
1280 X 1024
77.9kHz
72.0Hz
SXGA
1280 X 1024
80.0kHz
75.0Hz
WXGA
1440 X 900
55.5kHz
60.0Hz
WXGA
1440 X 900
70.6kHz
75.0Hz
Pin Assignments
Pin Number
15-Pin Side of the Signal Cable
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Video-Red
Video-Green
Video-Blue
N.C.
Detect Cable
GND-R
GND-G
GND-B
+5V
Ground
N.C.
DDC-Serial data
H-sync
V-sync
DDC-Serial clock
Plug and Play
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and,
depending on the level of DDC used, communicate additional information about its display capabilities.
2
The DDC2B is a bi-directional data channel based on the I C protocol. The host can request EDID information over the DDC2B channel.
8. Warranty Statement
Warranty Statement
LIMITED THREE-YEAR WARRANTY*
AOC Color Monitors sold within Europe
AOC International (Europe) GmbH warrants this product to be free from defects in material and workmanship for a period of Three (3) years after the
original date of consumer purchase. During this period, AOC International (Europe) GmbH will, at its option, either repair the defective product with new or
rebuilt parts, or replace it with a new or rebuilt product at no charge except as *stated below. The defective products that are replaced become the property
of AOC International (Europe) GmbH.
If the product appears to be defective, please contact your local dealer or refer to the warranty card when attached to the product.
Deliver the product freight pre-paid, along with the dated proof of purchase, to the AOC Authorized Service Center. If you cannot deliver the product in
person:
•
•
•
•
•
Pack it in its original shipping container (or equivalent)
Put the RMA number on the address label
Put the RMA number on the shipping carton
Insure it (or assume the risk of loss/damage during shipment)
Pay all shipping charges
AOC International (Europe) GmbH is responsible neither for any damage or loss during inbound transport damage nor to inbound product that was not
properly packaged.
AOC International (Europe) GmbH will pay the return shipping charges within one of the countries specified within this warranty statement. AOC
International (Europe) GmbH is not responsible for any costs associated with the transportation of product across international borders. This includes the
international border within the European Union.
* This limited warranty does not cover any losses or damages that occur as a result of
•
•
•
•
•
•
•
•
Shipping or improper installation or maintenance
Misuse
Neglect
Any cause other than ordinary commercial or industrial application
Adjustment by non-authorized source
Repair, modification, or installation of options or parts by anyone other than an AOC Authorized Service Center
Improper environment
Excessive or inadequate heating or air conditioning or electrical powers failures, surges, or other irregularities
This limited warranty does not cover any of the product firmware or hardware that you or any third party have modified or altered; you bear the sole
responsibility and liability for any such modification or alteration.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A PERIOD OF THREE (3) YEARS FOR PARTS AND LABOR FROM THE ORIGINAL DATE
OF CONSUMER PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR IMPLIED) APPLY AFTER THIS PERIOD.
AOC INTERNATIONAL (EUROPE) GMBH OBLIGATIONS AND YOUR REMEDIES HEREUNDER ARE SOLELY AND EXCLUSIVELY AS STATED
HERE. AOC INTERNATIONAL (EUROPE) GMBH LIABILITY, WHETHER BASED ON CONTRACT, TORT, WARRANTY, STRICT LIABILITY, OR
OTHER THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT OR DAMAGE IS THE BASIS OF THE CLAIM. IN
NO EVENT SHALL AOC INTERNATIONAL (EUROPE) GMBH BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE OR FACILITIES OR
EQUIPMENT, OR OTHER INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGE. SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. ALTHOUGH THIS
LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS, WHICH MAY VARY FROM COUNTRY TO
COUNTRY. THIS LIMITED WARRANTY IS ONLY VALID FOR PRODUCTS PURCHASED IN THE MEMBER COUNTRIES OF THE EUROPEAN UNION.