AOC A42W64AT4 Flat Panel Television User`s manual
Add to my manuals
19 Pages
AOC A42W64AT4, a 42-inch Plasma TV, offers a captivating viewing experience with its large WVGA 852 x 480 pixels resolution screen. Its impressive 1500 Cd/m2 brightness and 10000:1 contrast ratio deliver stunning visuals, while the wide 160° viewing angle ensures a great view from any seat. With built-in ATSC and NTSC receivers, you can enjoy a wide range of TV channels. The dual video, dual S-Video, dual Y Pb Pr, and PC D-SUB 15Pin inputs provide versatile connectivity options for various devices.
advertisement
USER’S MANUAL
A42W64AT4
Thank you very much for choosing the Envision Series Plasma TV.
We recommend that you take a few minutes to read carefully through this manual before installing and using the TV.
CONTENT
IMPORTANT SAFETY INSTRUCTIONS .................................................................................. ...1
Precautions and Reminders……………………………………………………………………………..2
Features and Fu n ction………………………………………………………….…………………….….4
Front Panel Control……………………………………………………………………………………….5
Basic Installation…………………………………………………………………………………………..6
Connection to other e q uipment………………………………………………………………………….7
Remote Control Function .......................................................................................................... ...9
OSD Menu Descriptions
Main Menu ...................................................................................................................... .…10
Setup Menu .................................................................................................................... .…10
Video Menu..................................................................................................................... .....11
Audio Menu……………………………………………………………………………………….…11
Feature Menu ........................................................................................................…......….12
EPG……………………………………………………………………………………………….….13
TVChannel ……………………………………………………………………..………………..….13
Specifications ......................................................................................................................... .....14
Troubleshooting ................................................................................................................... .....15
0
IMPORTANT SAFETY INSTRUCTIONS
Read before operating equipment
1. Read and follow all instructions.
2. Do not operate this apparatus near water.
3. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
4. Do not block any of the ventilation openings.
5. Clean only with a dry cloth.
14. Tilt/Stability- All televisions must comply with recommended international safety standards for tilt and stability properties of its cabinet design.
•
Do not compromise these design standards by applying excessive pull force to the front, or top, of the cabinet which
6. Do not defeat the safety purpose of the polarized or grounding-type plug. .A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and third grounding prong. The could ultimately overturn the product.
•
Do not endanger yourself, or children, by placing electronic equipment/toys on the top of the cabinet. Such items could unsuspectingly fall from the top of the set and cause product wide blade or third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet..
7. Protect the power cord from being walked on or pinched particularly at damage and/or personal injury.
15. Wall or Ceiling Mounting- The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer.
16. Power Lines- An outdoor antenna should be located away from power plugs, convenience receptacles, and the point where they exit from the apparatus.
8. Only use attachments/accessories specified by the manufacturer.
9. Use only with a cart, stand, tripod, bracket, or table specified by the lines.
17. Outdoor Antenna Grounding- If an outside antenna is connected to the receiver, make sure the antenna system is grounded so as to provide protection against voltage surges and built up of static manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
10. Unplug this apparatus during lightning storms or when charges.
Section 810 of the National Electric Code, ANSI/NFPA No.70-1984, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna unused for long periods of time.
11. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or discharge unit, size of grounding connectors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure below.
18. Object and Liquid Entry- Care should be taken so that objects do not objects have fallen into apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
12. This product may contain lead and mercury. Disposal of these materials may be regulated due to environmental considerations. For fall and liquids are not spilled into the enclosure through openings.
19. Battery Usage CAUTION –To prevent battery leakage that may result disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org
13. Damage Requiring Service -The appliance should be serviced by qualified service personnel when:
•
The power supply cord or the plug has been damaged; or
•
Objects have fallen, or liquid has been spilled into the appliance; or
•
The appliance has been exposed to rain; or
•
The appliance does not appear to operate normally or exhibits a marked change in performance; or
•
The appliance has been dropped, or the enclosure damaged. in bodily injury, property damage, or damage to the unit:
•
Install all batteries correctly, with + and - aligned as marked on the unit.
•
Do not mix batteries (old and new or carbon and alkaline, etc.).
•
Remove batteries when the unit is not used for a long time.
20. Keep this manual for future reference
Example of Antenna Grounding as per
NEC - National Electric Code
GROUND CLAMP
ANTENNA LEAD IN WIRE
Note to the CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
ELECTRIC SERVICE EQUIPMENT
(NEC SECTION 810-20)
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
(NEC SECTION 810-21)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING ELECTRODE SYSTEM
(NEC ART 250, PART H)
1
Precautions and Reminders
2
Do not place unit on uneven surfaces.
2
Do not place the TV in confined spaces or in a box when using it.
3
Unplug immediately if there is any malfunction, like no video, no audio, smoke or a bad odor.
3
3
Unplug immediately if other foreign materials are put inside TV box or if the TV fell down.
2
Do not throw any object like metals or flammable materials into the TV set.
2
Prohibit/Avoid opening TV cabinet
2
Precautions and Reminders
2 2
DO NOT use liquid cleansers or aerosol cleansers to clean the plasma display. Dilute a
Avoid direct sunlight, dusty, high humidity and smoky areas.
neutral detergent with water and wipe with a soft cloth or gently clean with some absorbent cotton. Remember to unplug the AC mains cord before cleaning the display.
3
Make sure to unplug the unit when not in use for a long period of time (2 days).
2
Do not cover or block any vents and openings.
Inadequate ventilation may shorten the life of the display unit and cause overheating.
3
Call service personnel to clean the internal part of the TV once a year.
2
Do not place the unit near water, such as bathtub, washbasin, kitchen sink laundry tub, swimming pool or in a damp basement.
Notice for Remote Control
Avoid Dropping
Avoid Dropping Avoid Liquids Avoid Aerosol Cleaners
1
4
2
5
8
7
0
3
6
9
3
Features and Function
42 inch(107cm)Large Screen Flat Panel Plasma Display
Panel Resolution: WVGA 852 x 480 Pixels
MAX Brightness of Panel: 1500 Cd/m
2
MAX Contrast Ratio of Panel: 10000:1
View Angle: Greater than 160°
Internal TV Tuner, Air:69 channels Cable:135 channels
Frequency Range:55.25MHz to 859.25MHz
ATSC receiver, MPEG-2 decoder
NTSC receiver, Video decoder
Dual Video, Dual S-Video
Dual Y Pb Pr (480i, 480P, 720P, 1080i)HDTV Ready
PC D-SUB 15Pin INPUT
D-SUB Vertical refresh rate 50Hz to 85 Hz
D-SUB Horizontal frequency 31KHz to 80KHz
DVI-D Signal(TMDS)INPUT, Support HDTV, SDTV
MIPS controller technology
Auto Scan TV Channels
Factory Presets
Universal Power Supply designed for worldwide application
≤ 350 W (Power consumer)
Closed Caption / V-chip For USA
4
Front Panel Control
⑦
⑥
⑤
④
③
②
①
- CH + - VOL +
MENU
①
MODE
Mode: Press to select input signal modes or use as Enter in Menu operation.
②
MENU
Menu: Press to enter Menu or exit Menu.
③
- VOL +
Left: Press to decrease the sound volume level or move Left in Menu operation.
Right: Press to increase the sound volume level or move Right in Menu operation.
MODE
④
- CH +
Down: Press to select the next lower Programme number or move Down in Menu operation.
Up: Press to select the next higher Programme number or move up in Menu operation
⑤
Power switch: Press to power on or power off the TV set .
⑥
●
LED: Power Indicator.
⑦
IR: Remote Control Sensor.
5
Basic Installation
1. Connect TV Cable and Power Cord to this PDP TV Set.
2. Plug Power Cord to your home power outlet.
3. Check front panel LED for proper power connection:
Blue color indicates this TV set is powered on;
Red color indicates this TV set is in standby state.
4. Push POWER KEY on Remote Control or Power key on
Front panel controls to switch the TV from stand by state to ON state.
This TV will power on and you can see display on screen within a few minutes.
5. Once you see information displayed on screen, press Digital button on Remote Control or MODE key on front panel continuously to select TV as input source. TV channel information will be displayed.
6. Use Auto channel search in “Setup Menu” to search all channels in your location. Refer to page
8 for “Setup Menu” operation procedure.
7. After Auto channel search is completed, press
“CHup” or “CHdown” key on remote control to select the next lower or higher channel.
Refer to the following pages for operating procedures: y Remote Control – page 9. y Setup Menu – page 10. y TV Channel Arrangement – page 13.
POWER KEY
Ch14.0 12:00AM
TV channel information
6
Connection to other equipment
Please connect this TV Set to other equipment as picture below.
You may have many types of equipment as: DVD, VCD, VCR, Set Top Box, X-Box and so on.
(View from back of the TV set,left to right)
INPUT CONNECTION OF VIDEO SIGNAL(DVD/VCD/VCR)
s-video Y R W B
AV1-INPUT
s-video Y R W
7
Connection to other equipment
G B R R W
INPUT CONNECTION OF PC SIGNAL(PC/DVD)
We have 2 component signal input jacks: Y Cb Cr and Y Pb Pr. The R / L is
Audio input for every Y Cb Cr and Y Pb Pr.
If your DVD or Set Top Box have Y Cb
Cr or Y Pb Pr output, you can connect it to
Y Cb Cr or Y Pb Pr input jack. And select to
Y Cb Cr or Y Pb Pr source input. (Some
DVD or Set Top Box need to set to Y Cb Cr or Y Pb Pr output)
Notice: If you see that display abnormality in screen, you need to check the cable connection and DVD setup.
Notice: If you see that display abnormality in screen, you need to check the cable connection and DVD setup.
▲ Notice: The PC output can not set out of
range.The highest resolution input is
1280 X 1024 / 60Hz.
Some PC models cannot be connected to the set.
24PIN DVI R/L INPUT 15PIN DVI R/L INPUT
●
D-SUB 15 Pin:
Connect D-SUB signal cable(VGA cable)from PC to D-SUB jack at the back of this display.
And connect the earphone cable from PC earphone output jack to AUDIO input jack near to the
D-SUB jack.
Setup:
Use the key “Digital”in Remote Control Transmitter or “MODE”key on Front panel controls to select source to “VGA”state. Then turn on the PC.
●
DVI-D:
of this display. And connect earphone cable from equipment with earphone output jack to
AUDIO input jack near the DVI-D jack.
Setup:
Use the key “Digital”in Remote Control Transmitter or “MODE”key on Front panel controls to select source to “DVI”state. Then turn on the equipment.
8
Remote Control Function
“
Wide Mode”
Normal, Zoom ,Wide, Cinema display select
“
EPG”
Display the state, source
“
TV”
Wide Mode
TV
EPG
Video
SLEEP
POWER
Digital
“
POWER”
The TV Set turn on /turn off key
“
Video”
AV1 CVBS Rear /AV1 S-Video
Rear/ AV2 CVBS Side/ AV2
S-Video Side / AV3 component 1/
AV4 component 2
TV source select, into TV state
CC
M
TS
“
SLEEP ”
Select timer into power down
state. off→30→60→90→off left
Up
Enter right
“
Digital”
VGA/DVI source input
“ MTS ”
To select audio program options
“
CC”
D ow n
To select close caption options
M en u
EX
IT
“ Up▲/Down▼”
(CC1,CC2……)
Vol up
Mute
CH up
Move the cursor up and down on the Menu
“
ENTER ”
To enter sub Menu or sub item .
To enter Menu mode .
Vol down CH down
“
MENU”
Remote Control Function
“
left ◄ / right ►”
Use left ◄/ right ► to select or adjust an item.
1
2
3
“
MUTE”
Mute the sound
“
Vol up / Vol down”
Press Vol up/ Vol down key to adjust volume .
“ 0~9 number”
To enter TV channel number
“
z
”
To enter sub channel number for digital channels .
4
7
5
8
6
9
Pre-CH
“
EXIT”
To exit Menu or other OSD .
“
CH up / CH down”
Press to select the next lower or higher Program number.
“
Pre-CH”
TV channel return, see last
TV channel .
9
OSD Menu Descriptions
Main Menu
1. Press “MENU” key on remote control or front panel controls to bring up Main Menu.
2. Press “ ” or “ ” to move the cursor up and down the sub menu list.
3. Press “ ” or “ ” to select sub menu item.
4. Press "Enter" to enter sub-item then use “ ” or “ ” to adjust.
Setup Menu
1. Tuning Band: Select TV signal source between Air and Cable. Select Cable if you are connecting to a cable box and select Air if you are directly connecting to the antenna.
2. DTV Signal: Display signal strength to aid antenna adjustment.
3. Auto Ch Search: Automatically scan and store all TV channels.
4. Manual Ch Set: Enter channel setup table.
5. Channel Labels: Display and edit channel names.
6. Menu Language: Select language for menu
(English Español Français Portuguese)
.
y DTV signal menu indicates signal strength in real-time. y Auto channel scan menu displays channel number being scanned. y Manual Channel Set Menu
Displays all the channel numbers that are found.
Tune either to ATSC or NTSC channels.
Add or delete Channel number.
y Channel Labels Menu allows user labeling.
10
OSD Menu Descriptions
Video Menu
.
1. Press “ ” or “ ” to move the
cursor up or down the sub-item list.
2. Press "Enter" to enter the highlighted sub-item menu.
3. Press “ ” or “ ” to adjust the value of the sub-item.
4. Press "Enter" again to exit the sub-item.
Contrast: Contrast adjustment, 0 ~ 100.
Brightness: Brightness adjustment, 0 ~ 100.
Color: Color chroma adjustment, 0 ~ 100.
Tint: Tint adjustment, 0 ~ 100.
Aspect Ratio: Aspect Ratio selection.
Normal
Zoom Wide Cinema.
Settings: Restore default setting.
Audio Menu
1. Press “ ” or “ ” to move the cursor up
or down the sub-item list.
2. Press "Enter" to enter the highlighted sub-item menu.
3. Press “ ” or “ ” to adjust the
value of the sub-item.
4. Press "Enter" again to exit the sub-item.
Audio Language:
English
Spanish French
Portuguese.
Bass: Bass adjustment, 0 ~ 100.
Treble: Treble adjustment, 0 ~ 100.
Balance: Balance adjustment, 0 ~ 100.
Restore Default: Restore Audio Language,
Treble, Bass, and Balance setting to default.
11
OSD Menu Descriptions
Feature Menu
1. Press “ ” or “ ” to move the cursor up
or down the sub-item list.
2. Press "Enter" to enter the highlighted sub-item menu.
3. Press “ ” or “ ” to adjust the
value of the sub-item.
4. Press "Enter" again to exit the sub-item.
Time Set : The default time when you first set up theTV is 12:00 midnight. The internal clock starts from 12:00am. In the time set menu, first select the time zone you are in and manually change the time to the present time. Press Enter to confirm the time and exit the menu. Note that whenever you switch the MAINS off, you need to set the time again when you turn the TV on.
Sleep Timer: Select minutes into standby
Off
30 60 90.
Password Set: Enter and change
Parental Control Password.
Parental Control: Setup TV and Movie rating controls.
White Screen:Press “Enter”to white screen.
Parental Control Menu: Controls viewing of rated TV and Movie programs.
Note:Need password to change settings.
Initial Default password is: 0000.
Important : If you have forgotten your
Password
Use the code [0711] to enter into the
Password Set menu item to change your password.
You can also use the code [0711] to change your Parental Controls settings.
12
OSD Menu Descriptions
Closed Captions section
1. Press “CC” key on remote control to select closed captions mode.
NTSC TV: Off..CC1 ..CC2
.. …
ATSC TV: Off
..CS1 ..CS2.. …
2. Select desired closed caption mode.
3.Closed captioning for analog
NTSC channels is transmitted as CC1/CC2/CC3/CC4.Closed captioning for digital channels is transmitted as CS1/CS2/CS3
/CS4/CS5/CS6 or occasionally
CC1/CC2/CC3/CC4. You need to select the option you want for analog channels and digital channels separately.
NTSC TV
ATSC TV
CC1
CS1
EPG
Press the “EPG” key on the remote control to display the Electronic
Program Guide (EPG). A message window will be displayed on screen.
EPG Message Window
TV channel arrangement
Ch 5.2
Analog NTSC channels are
Numbered as2.0, 5.0, 11.0 etc.
Digital ATSC channels are numbered as 2.1, 5.1, 5.2, 11.1, 11.2 etc depending on your local transmittors. Note that each digital channel may comprise of several sub-channels. For your convenience, this television groups all analog channels together followed by all digital channels together.
To select a digital channel using the remote control:
1. To go to channel 5.2, enter main channel number (5).
2. Press the “•” key.
3. Enter the sub-channel number (2).
13
Specifications
Item Specification
Panel
Spec
TV Mode
Screen size
Aspect
Display pixels
Effective display size
Number of color
Contrast Ratio
Peak brightness
TV Tuning
Sound system
Color system
42 inch plasma display panel
16:9
852 x 480 (WVGA)
932 mm x
532 mm
16.7 million colors
10000:1 (in dark room)
1500 cd/㎡
1 Tuners, Air:69 channels Cable:135 channels
M
ATSC / NTSC
Video Mode
AV1 ( S_Video/Video)
AV2 ( S_Video/Video)
AV3 / AV4
COMPONENT X 2
(Y Cb Cr/Y Pb Pr)
Video RCA x 1 NTSC
S-Video1 x 1 NTSC
Video RCA x 1 NTSC
S-Video2 x 1 NTSC
480i
YCbCr/YPbPrx 2
1080i
480P
720P
Analog:D-Sub 15 pin
DDC / 2B
FH: 31KHz to 80KHz , FV:50Hz to 85Hz
Audio: L/R x 1
Audio: L/R x 1
Audio: L/R x 2
Signal input
Plug and play
Support Frequency
PC Mode
DVI Mode
Accessory
D-Sub Mode
D-Sub Audio
Signal input
Plug and play
DVI Mode
DVI Audio
VESA: 640 x 480
VESA: 800 x 600
VESA: 1024 x 768
VESA: 1280 x 1024
Earphone (3.5ø)
Digital:DVI-D 24 pin
DDC / 2B
720P
1080i
480P
Earphone (3.5ø)
Power
Power input sources
Power consumption
AC 100-240V , 50/60Hz
≤
350W
Environment
Operation Temperature
Storage Temperature
+ 0 °C ~ + 40 °C
- 10 °C ~ + 50 °C
10% -- 85% Humidity
Dimension Width x Height x Thickness 1038 x 726.5 x 240 (mm)
Net weight With Stand 34Kg
Remote Control Transmitter, Battery X 2, Power Cord, User’s Manual, RCA Cable,
D-SUB Cable,DVI Cable.
14
Troubleshooting
Symptoms Checks
Picture freezes in antenna mode.
The TV does not react to remote controller commands.
•Please ensure the antenna is properly connected.
•Please switch off the mains and switch on again.
•Re-install the channels if needed.
Picture breaks up in DVI mode, especially when a set top box is connected.
The picture is jerky or is corrupted (multiple small square boxes seen) in ATSC mode.
Some channels are missing
/ are not found.
No Picture, No Sound
Interference,Noisy
•The TV is trying to read the HDCP code sent by the set top box.
•Please switch off the set top box and switch on again.
•The signal could be weak. Check the DTV signal via Menu
--> Setup --> DTV Signal.
Adjust the direction of your antenna to improve the signal. Re-install the channels if needed.
•Press the channel number to check if the channel exists, if yes, go to the Manual Channel Set Menu (Menu-->Setup-->
Manual ch set), and add the channel.
•Go to the Setup Menu (Menu-->Setup) and install the channels again, searching Air/Cable as appropriate.
•Check the power cord and power outlet.
•Check whether the TV power switch is on.
•Verify the front panel LED is showing blue color.
•Check connections for the selected input source.
•Verify that external signal for the selected input is active.
•Check Video/Audio settings.
•The signal could be weak. Check the DTV signal via Menu
--> Setup --> DTV Signal
Adjust the direction of your antenna to improve the signal
Re-install the channels if needed.
•Check antenna connection, aerial location, and direction.
•Check and relocate nearby electrical appliances.
•Check fluorescent lights.
•Check cars/motorcycles.
•Check antenna connection, aerial location, and direction
Re-scan Channels.
Distorted picture,Noisy
•Check whether colour setting is at minimum.
•Adjust video menu picture settings or reset to default.
No Colour,Normal Sound
•Check audio input connections.
•Check whether TV audio is in MUTE mode.
•Adjust audio volume to audible level.
Normal Colour,No Sound
15
Some parts of the
screen do not light up
After-images appear
DVD
Troubleshooting
The plasma TV panel is manufactured using an extremely high level of precision technology, however, sometimes some parts of the screen may be missing picture elements or have luminous spots. This is not a malfunction.
Do not allow a still picture to be displayed for an extended period, as this can cause a permanent after-image to remain on the Plasma TV.
Examples of still pictures include logos, video games, computer images, and Teletext.
Note:
The permanent after-image on the Plasma TV resulting from fixed image use is not an operating defect and as such is not covered by the Warranty.
This product is not designed to display fixed images for extended periods of time.
DTV signal jumps from 0 to
100 and back.
•The signal is too weak to display a picture. Try to re-orient the antenna to a suitable direction and auto-tune again.
No closed captioning seen when the TV is connected to a set top box.
•Press the CC button on the remote controller to switch off the closed captioning. Then switch it on again.
16
Envision Peripherals Inc.
47490 Seabridge Dr.
Fremont, CA 94538 www.AOCdisplay.com
Tech Support: 1-888-662-9888
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement