User`s manual | AOC CT700G Computer Monitor User Manual

CT700G
CT710G
CT720G
CT740G
User’s
Manual
2
Thank you very much for choosing the AOC Color Monitor. We
recommend that you take a few minutes to read carefully through
this brief but comprehensive manual before installing and
switching on the monitor. Please keep this manual in a safe place
for you future reference.
Plug & Play Drivers for the AOC Series Monitors are available at:
www.aocmonitor.com
CHECKING THE CONTENTS OF THE MONITOR PACKAGE
The product package should include the following items:
1.
2.
3.
4.
5.
Monitor
Owner's Manual
Power Cord
Swivel Base
Audio Cable/DC Power Cable ( For CT740g only )
FCC Class B Radio Frequency Interference Statement
WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for
help.
NOTICE :
1. The changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be
used in order to comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modification to this
equipment. It is the responsibilities of the user to correct such
interference.
As an ENERGY STAR Partner Envision Peripherals, Inc. has
determined that this product meets the ENERGY STAR
guidelines for energy efficiency.
WARNING:
To prevent fire or shock hazard, do not expose the monitor to rain
or moisture. Dangerously high voltages are present inside the
monitor. Do not open the cabinet. Refer servicing to qualified
personnel only.
3
PRECAUTIONS
 Do not use the monitor near water, e.g. near a bathtub,
washbowl, kitchen sink, laundry tub, swimming pool or in a wet
basement.
 Do not place the monitor on an unstable cart, stand, or table. If
the monitor falls, it can injure a person and cause serious
damage to the appliance. Use only a cart or stand
recommended by the manufacturer or sold with the monitor. If
you mount the monitor on a wall or shelf, use a mounting kit
approved by the manufacturer and follow the kit instructions.
 Slots and openings in the back and bottom of the cabinet are
provided for ventilation. To ensure reliable operation of the
monitor and to protect it from overheating, be sure these
openings are not blocked or covered. Do not place the monitor
on a bed, sofa, rug, or similar surface. Do not place the monitor
near or over a radiator or heat register. Do not place the monitor
in a bookcase or cabinet unless proper ventilation is provided.
 The monitor should be operated only from the type of power
source indicated on the label. If you are not sure of the type of
power supplied to your home, consult your dealer or local power
company.
 The monitor is equipped with a three-pronged grounded plug, a
plug with a third (grounding) pin. This plug will fit only into a
grounded power outlet as a safety feature. If your outlet does
not accommodate the three-wire plug, have an electrician install
the correct outlet, or use an adapter to ground the appliance
safely. Do not defeat the safety purpose of the grounded plug.
 Unplug the unit during a lightning storm or when it will not be
used for long periods of time. This will protect the monitor from
damage due to power surges.
 Do not overload power strips and extension cords. Overloading
can result in fire or electric shock.
 Never push any object into the slot on the monitor cabinet. It
could short circuit parts causing a fire or electric shock. Never
spill liquids on the monitor.
 Do not attempt to service the monitor yourself; opening or
removing covers can expose you to dangerous voltages and
other hazards. Please refer all servicing to qualified service
personnel.
 To ensure satisfactory operation, use the monitor only with UL
listed computers which have appropriate configured receptacles
marked between 100 - 240V AC, Min. 2.5A.
 The wall socket shall be installed near the equipment and shall
be easily accessible.
 Attention: Disconnect the power cord to stop the power supply
to the monitor.
TECHNICAL SUPPORT(FAQ)
Plug & Play DDC1/2B Feature
This monitor is equipped with VESA DDC1/2B capabilities
Power LED is not on
according to the VESA DDC STANDARD. It allows the monitor to
*Power Cord should be connected
inform the host system of its identity and, depending on the level
No Plug & Play
of DDC used, communicate additional information about its display
*Check if the PC System is Plug & Play compatible
capabilities. The communication channel is defined in two levels,
*Check if the Video Card is Plug & Play compatible
DDC1 and DDC2B.
*Check if the D-15 plug pin of Video Cable is bent
The DDC1 is a unidirectional data channel from the display to the
*Make sure the AOC Monitor Drivers are installed
host that continuously transmits EDID information. The DDC2B is
(AOC
Monitor
Drivers
are
available
at:
a bidirectional data channel based on the I²C protocol. The host
www.aocmonitor.com)
can request EDID information over the DDC2B channel.
Picture is fuzzy
*Adjust the Contrast and Brightness Controls.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF
Picture bounces or a wave pattern is present in the
THERE IS NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS
picture
MONITOR TO OPERATE PROPERLY, THERE MUST BE A
*Move electrical devices that may cause electrical
VIDEO INPUT SIGNAL.
interference.
This monitor meets the Green Monitor standards as set by the
The power LED is ON (orange) but there’s no video or
Video Electronics Standards Association (VESA) and/or the United
no picture.
States Environmental Protection Agency (EPA) and The Swedish
*Computer Power Switch should be in the ON position.
Confederation Employees ( NUTEK ). This feature is designed to
*Computer Video Card should be snugly seated in its slot.
conserve electrical energy by reducing power consumption when
*Make sure monitor’s video cable is properly connected to
there is no video input signal present. When there is no video input
the computer.
signal this monitor, following a time-out period, will automatically
*Inspect monitor’s video cable and make sure none of the
switch to an OFF mode. This reduces the monitor's internal power
pins are bent.
supply consumption. After the video input signal is restored, full
*Make sure computer is operational by hitting the CAPS
power is restored and the display is automatically redrawn. The
LOCK key on the keyboard while observing the CAPS
appearance is similar to a "Screen Saver" feature except the
LOCK LED. The LED should either turn ON or OFF after
display is completely off. The display is restored by pressing a key
hitting the CAPS LOCK key.
on the keyboard, or clicking the mouse.
Missing one of the primary colors (RED, GREEN, or
USING THE RIGHT POWER CORD:
BLUE)
The accessory power cord for the Northern American region is the
*Inspect the monitor’s video cable and make sure that none
wallet plug with NEMA 5-15 style and is UL listed and CSA
of the pins are bent.
labeled. The voltage rating for the power cord shall be 125 volts
AC.
Supplied with units intended for connection to power outlet of
personal computer: Please use a cord set consisting of a minimum
No. 18 AWG, type SJT or SVT three conductors flexible cord. One
end terminates with a grounding type attachment plug, rated 10A,
250V, CEE-22 male configuration. The other end terminates with a
molded-on type connector body, rated 10A, 250V, having standard
CEE-22 female configuration.
4
INSTALLATION INSTRUCTIONS
SWIVEL BASE
To attach the swivel base to the monitor, do the following:
 Carefully turn the monitor on its side or upside down.
(see figure 1)
 Locate the cavities at the bottom front of the monitor.
 Insert the pegs on the swivel base into these cavities. Push the
swivel base forward until the swivel base locks in place.
 To remove the swivel base, hold the bottom of the swivel base,
then push it out.
POWER CORD
Power Source:
1. Make sure the power cord is the correct type that required in
your area.
2. This monitor has a universal power supply that allows operation
in either 100/120V AC or 220/240V AC voltage area (No user
adjustment is required).
3. Connect the power cord into your monitor’s power input socket,
and then plug the other end into a 3-pin AC power outlet. The
power cord may be connected to either a wall power outlet or
the power outlet socket on your PC, depending on the type of
power cord supplied with your monitor.
VIDEO CABLE
Connecting the Video Cable: the monitor comes with a built-in
video cable. Plug the signal cables 15-pin connector into the
computer's video port and tighten the two screws on the cable
connector. (see figure 2)
Caution:Don’t bend the signal cable, otherwise it will break the
inner wire.
Connecting the Power Cord: Plug the power cord into the
monitor's AC power jack. Then plug the power cord into a
grounded AC outlet, UL-approved power strip, or the power
output socket on your PC.
Caution: If the AC outlet is not grounded, install the proper
grounding adapter (not supplied).
Connecting the Audio Cable ( CT740g only ): Plug audio cable
between the computer multi-media (or sound) card's audio output
and monitor's audio input.
Connecting the DC Power Cable ( CT740g only ): Plug DC
power cable between monitor to swivel base for audio power
OPERATING INSTRUCTIONS
GENERAL INSTRUCTIONS
The other control knobs are located at the base of the monitor
(See Figure 3). By changing these settings, the picture can be
adjusted to your personal preferences.
 The power cord should be connected.
 Connect the video cable from the monitor to the video card.
 To turn the monitor on, press the power switch to ON position.
The power indicator will light up.
 Your monitor features a unique quick switch system which
provides a picture within seconds after the monitor is switched
on.
NOTES
 Do not install the monitor in a location near heat sources such
as radiators or air ducts, or in a place subject to direct sunlight,
or excessive dust or mechanical vibration or shock.
 Save the original shipping carton and packing materials, as they
will come in handy if you ever have to ship your monitor.
 For maximum protection, repackage your monitor as it was
originally packed at the factory.
 To keep the monitor looking new, periodically clean it with a soft
cloth. Stubborn stains may be removed with a cloth lightly
dampened with a mild detergent solution. Never use strong
solvents such as thinner, benzene, or abrasive cleaners, since
these will damage the cabinet. As a safety precaution, always
unplug the monitor before cleaning it.
Figure 1 Installing and Removing the Swivel Base
Figure 2
Connecting Cables
Figure 3 External Control Knob
1
2
2
3
4
1
3
5
7
5
6
CONNECTING CABLES
1.
Power Cord
2.
Signal Cable
3.
VGA Card Adapter
4.
5.
PC Audio Output
DC Output
EXTERNAL CONTROLS
1.
Shuttle Knob
2.
Power Indicator
3.
Power button
HOW TO ADJUST A SETTING
1. Press the Shuttle Knob Key to make the OSD window
appear. See figure 4.
2. Rotate the Shuttle Knob to select the desired function.
See figure 4.
3. Press the Shuttle Knob again to select the function that you
want to adjust.
4. Rotate the Shuttle Knob to change the settings of the current
function.
5. When the OSD window is active, it shows the input signal
timing. The "H" stands for the horizontal frequency and "V"
for the vertical frequency.
6. To exit and save, select the exit function, or leave the monitor
alone for 10 seconds. If you want to adjust any other function,
repeat steps 2-4.
FRONT PANEL CONTROL PANEL CONTROL
 Power button :
When pressed, the monitor enters the off mode, and
the LED flashes. Press again and hold to restore
normal status.
 Shuttle Knob :
The Shuttle Knob is used to control the monitor
functions. Rotate to switch functions or adjust settings.
Press to select or execute a function .
 Power Indicator :
Green — Power On mode.
Blinking Green — Off mode.
1024 X 768
Figure 4
The OSD Message
ADJUSTING THE PICTURE
1.
CONTRAST
Adjust the picture contrast.
2.
BRIGHTNESS
Adjust the picture brightness.
3.
H- CENTER
Adjust the horizontal position
of the picture.
4.
H- SIZE
Adjust the picture’s horizontal
size.
6
5.
V- CENTER
Adjust the vertical position of the picture.
6.
V- SIZE
Adjust the picture’s vertical size.
7.
ZOOM
Adjust the picture’s horizontal and vertical size simultaneously.
8.
PINCUSHION
Adjust the pincushion and barrel
9.
TRAPEZOID
Adjust the picture’s trapezoid distortion.
10.
PIN-BALANCE
Adjust to compensate the pincushion unbalance.
11.
PARALLELOGRAM
Adjust the picture to be a rectangle.
12.
ROTATION
Adjust the picture tilt to horizontal position.
6500°K/9300°K
( COLOR
TEMPERATURE )
USER COLOR
( Red / Blue )
The color temperature for 6500°K is x=0.313, y=0.329 and 9300°K is x=0.283, y=0.297. It
presents two different color sets on the screen. You can select 9300°K or 6500°K by pressing
the Shuttle Knob.
If the 9300°K normal white or 6500°K warmer white do not satisfy your desire, properly adjust
R . B GAIN controls to obtain your optimum whiteness level.
DEGAUSS
If color impurity occurs when moving or swiveling the monitor, press the Shuttle Knob and
degauss to fix the picture condition.
MOIRE REDUCE
Moire is the result of interference between the phosphor layout and the video signal. In some
cases, you may find the moire very noticeable. Press the Shuttle Knob to enter in the moire
reduce setting. Please adjust the level to the optimum condition. Note: Too high of a setting
will cause the picture to shake.
17.
RECALL
Press RECALL to restore the monitor to factory settings.
18.
EXIT
Close OSD window.
19.
SELECT LANGUAGE
Select the language as you like.
13.
14.
15.
16.
7
SPECIFICATION
CRT
Viewable Image Size
Video
Separate Sync.
H/V-sync.
Scanning Frequency:
Horizontal
Vertical
Max. Resolution
Video Dot Rate
Factory Preset mode :
User Programmable
mode :
Power Source
Operating
Humidity
Dimension
CT700:
CT740:
Weight
CT700:
CT740:
Signal Cable
Plug & Play
EPA ENERGY On mode
STAR®
Off mode
Power consumption
Preset display area
Audio output
(CT740 only)
Regulations
Factory Preset Timing Table
43.2cm(17"), 90º deflection, 29mm neck,
0.23mm(H), 0.27mm(D) dot pitch
40.6cm (16"), diagonal
0.7Vpp, R, G, B Analog
TTL Level
Positive/Negative
30kHz to 72kHz automatically
50Hz to 160Hz automatically
1280 × 1024
110MHz
6
STANDARD
RESOLUTION
HORIZONTAL
FREQUENCY
VERTICAL
FREQUENCY
IBM
720 x 400
31.5kHz
70Hz
VGA
640 x 480
31.5kHz
60Hz
VESA/85
640 x 480
43.3kHz
85Hz
VESA/85
800 x 600
53.7kHz
85Hz
VESA/85
1024 x 768
68.7kHz
85Hz
VESA/60
1280 x 1024
64.0kHz
60Hz
8
Universal AC 100-240V, 50Hz/60Hz
0°C to 40°C ambient
10% to 85% relative, non- condensing
CONNECTOR PIN ASSIGNMENT
(Monitor&Base)
410(W) × 402(H) × 420(D)mm
410(W) × 440(H) × 420(D)mm
15.5 kg(Net)
16.3 kg(Net)
Attached Mini D-sub 15 Male
DDC1/2B
 75 W
5W
75 Watts Max.
310mm × 230mm
1
5
6
10
11
15
15 -Pin Color Display Signal Cable
PIN NO.
1.
2.
3.
4.
5.
6.
7.
8.
1W (per channel)
UL, CSA, FCC, FDA
8
DESCRIPTION
Red
Green
Blue
Ground
Ground
R-Ground
G-Ground
B-Ground
PIN NO.
9.
10.
11.
12.
13.
14.
15.
✲
DESCRIPTION
NC
Ground
Monitor Ground
DDC-Serial Data
H-Sync
V-Sync / *V-Clk
DDC-Serial Clock
For DDC
Download PDF

advertising