APC Silcon
10-40kW 400V UPS
Installation Guide
Copyright 2000 APC Denmark ApS
This manual is subject to change without
notice and does not represent a commitment
on the part of the vendor
Thank You!
Thank you for chosing the APC Silcon Series UPS. Please read this Installation Guide
thoroughly prior to installing the system. It provides important information on safe and
efficient installation.
The installation and use of this product must comply with national, federal, state, municipal
and local codes.
Safety Symbols used in this manual
WARNING!
Indicates a hazard which, if not avoided, could result in injury or death.
CAUTION!
Indicates a hazard which, if not avoided, could result in damage to the
product or other property.
NOTICE!
Read and pay attention to this important information.
WARNING!
This UPS unit contains hazardous AC and DC voltages. Only qualified electricians should install
the UPS, AC line and external batteries, and must be familiar with batteries and battery
installation.
Before installing, maintaining or servicing the UPS, shut off the UPS and disconnect all sources
of AC and DC power.
As the UPS has no built-in disconnection devices to switch off external AC and DC input power,
ensure that disconnection devices are provided as separate parts in connection with the
installation!
The installer must provide each external disconnecting device for this UPS system with labels
with the following text:
“Isolate the Uninterruptible Power Supply (UPS) as instructed in this guide before working on
circuit”
AC and/or DC voltage will always involve a potential risk of AC voltage at UPS output generated
from either batteries or mains. To avoid equipment damage or personal injury, always assume
that there may be voltage at UPS output.
This system is equipped with an auto-start function. If activated, the system may start without
warning. Refer to the “Programming” section of this guide for information on de-activation.
TEST BEFORE YOU TOUCH!
To reduce the risk of fire or electric shocks, install the UPS and external batteries in a
temperature and humidity controlled indoor area, free of conductive contaminants.
UPS batteries are high-current sources. Shorting battery terminals or DC terminals, DC busbars
can cause severe arcing, equipment damage and injury. A short circuit can cause a battery to
explode. Always wear protective clothing and eye protection and use insulated tools when
working on batteries.
CAUTION!
This unit contains components sensitive to electrostatic discharge (ESD). If you do not follow the
ESD procedures, you may cause severe damage to electronic components.
990-4050
2
Installation Guide APC Silcon 10-40kW 400V UPS
Contents
1.0
Introduction
5
1.1
Tools and Equipment
5
2.0
Unpacking
6
3.0
Installation
8
3.1
3.1.1
3.2
3.2.1
3.2.2
3.2.3
3.2.4
3.2.5
Requirements on Site
Cabinet Dimensions H*xWxD - 1400xWx800 [mm]. Width as in below table:
Footprint
600mm UPS Cabinet with 1xBP I or Isolation Transformer
800mm UPS Cabinet with 1xBP I or Built-in Isolation Transformer, or 2xBP I
1000mm Cabinet for 10-20kW UPS with 3xBP I
600mm Cabinet for 40kW UPS without Batteries
1000mm Cabinet for 40kW UPS with 2xBP I
8
8
10
10
10
11
11
12
4.0
External Connection
13
4.1
4.1.1
4.1.2
4.2
4.2.1
4.3
4.4
4.4.1
4.5
4.6
4.6.1
4.6.2
4.6.3
4.6.4
4.6.5
4.6.6
4.7
4.7.1
4.7.2
4.7.3
4.7.4
4.7.5
4.8
4.8.1
4.8.2
4.8.3
4.8.4
4.8.5
Connecting the UPS
Connecting the 10-20kW UPS
Connecting the 40kW UPS
System Integration Interface
Connections
Parallel Board
Communication Interface Board
Connections
Connecting of APC Silcon Tripel Chassis
APC Silcon Triple Chassis
Safety Warnings
Product Description
Installing Management Peripherals
Powering the APC Silcon Triple Chassis
Troubleshooting
Product Specifications
APC Silcon Battery Cabinets
Cabinets
Preparing Batteries
Mounting Batteries
Final Checks
APC Silcon Battery Cabinets
Battery Breaker Box/Fuse-box
Battery Breaker Box
Battery Breaker Box Connection Diagram
Fuse-box
Fuse-box Connection Diagram
UPS with External Battery in Battery Breaker Box/Fuse-box Configuration
13
13
15
17
18
19
22
22
23
24
24
24
25
27
28
29
32
33
33
35
37
38
40
41
42
43
44
45
5.0
Programming Parameters
46
5.1
5.1.1
5.1.2
5.2
5.2.1
5.2.2
5.3
5.3.1
5.3.2
5.4
5.4.1
Parameters
Programming Keys
Programming Example - Switch to Bypass Operation
System Configuration
Programming Example - Change Charge Voltage to 446
Programming Example - Change to Output Isolation Transformer available
Programming Parameters for Advanced Parallel Operation
Description of Settings
Programming example
Battery Monitor
Installation of new batteries
46
47
48
48
50
51
52
52
53
53
53
6.0
Options/Accessories
54
6.1
6.1.1
6.1.2
Service Bypass Panel for Single Operation
Wiring up UPS with SBP in TN-C-S Network
Wiring up UPS with SBP in TN-S Network
54
56
56
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
3
6.1.3
6.2
6.2.1
6.2.2
Operating The External Service Bypass Switch
Service Bypass Panel for Parallel Redundant Operation
Two Parallel Systems with Service Bypass Panel
Parallel/Redundant Operation with Service Bypass Panel and External Battery
via MCCB
Operating External Service Bypass Switch for Parallel Systems
Isolating One UPS for Service/Maintenance
Switching Back to Normal Parallel/Redundant Operation
Intersystem Synchronization Unit
Relay Board
Relay Board/Relay Functions
Weight Equalizer
Remote Display
Extension of Remote Display Communication Distance
Remote Display Installation
Remote Display Use
Isolation Transformer
Connecting Isolation Transformer
Wiring up UPS with External Yyn0 Isolation Transformer at Output
Wiring up UPS with External Yyn0 Isolation Transformer at Input
Wiring up UPS with External Optional Dzn0 Isolation Transformer at Input
Wiring up UPS with External Optional Dzn0 Isolation Transformer at Output
Wiring up UPS with External Optional Dyn11 Isolation Transformer at Input
61
62
66
67
68
69
70
72
74
74
76
77
78
79
81
82
83
84
85
7.0
System Specifications
86
7.1
7.2
Technical Data
Back-up Time / Dimensions / Weigh
86
86
8.0
Warranty
87
8.1
APC Silcon Series Limited Factory Warranty
87
6.2.3
6.2.4
6.2.5
6.3
6.4
6.4.1
6.5
6.6
6.6.1
6.6.2
6.6.3
6.7
6.7.1
6.7.2
6.7.3
6.7.4
6.7.5
6.7.6
57
59
60
9.0
Appendix
88
9.1
Table 1. Installation Planning Data
88
10.0
How to Contact APC
90
990-4050
4
Installation Guide APC Silcon 10-40kW 400V UPS
Introduction
1.0 Introduction
Power regulation varies from country to country, and information given in this installation
guide can therefore only be of a general nature. Electricians should therefore always refer to
national and local electrical codes prior to installing the UPS system.
1.1
Tools and Equipment
CAUTION!
Heavy equipment. To prevent personal injury or equipment damage, take extreme care when
handling and transporting UPS cabinet and equipment.
CAUTION!
Ensure that front doors are in place and that internal front cover is fastened by screws before
attempting to lift or transport the system.
This section lists all tools and equipment required to install all UPS configurations. See also
section 4.0 of this guide for further details on connection.
Tools:
• 10mm socket
• 13mm socket-deep
• 17mm socket
• 19mm socket-deep
• 19mm combo wrench
• Small flat head/regular screwdriver
• #3 philips screwdriver
• Compression lug crimping tool
• Knock-out set (for glands)
Equipment:
• Compression lugs for cable terminations
• Cable to Service Bypass Panel from system feeder
• Cable to UPS input from Service Bypass Panel
• Cable to Service Bypass Panel from UPS output
• Cable from Service Bypass Panel to customer distribution
• Cable to UPS input from external batteries/external Battery Breaker Box
(systems with external battery)
• Solid core, control cable to UPS from Service Bypass Panel
• Solid core, control cable to UPS from external batteries/external Battery
Breaker Box
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
5
Unpacking
2.0 Unpacking
NOTICE!
Unless otherwise specified by the shipping company use a fork lift to unload equipment from
pallet
1. To unpack UPS unit, remove top and bottom screws from side plates of packaging and lift up side plates
2. Verify compliance between type label on reverse side of front door and system ordered. Check input and
output voltage
3. Copy type label data to label copy below for easy identification of system
4. Use fork lift to transport system to installation site
5. Open UPS doors and unscrew metal straps mounted on front cover of UPS
990-4050
6
Installation Guide APC Silcon 10-40kW 400V UPS
Unpacking
Copy of type label
PLEASE RECYCLE
The shipping materials for the APC Silcon UPS are recyclable. Please save them for later use or
dispose of them appropriately.
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
7
Installation
3.0 Installation
3.1
Requirements on Site
All system parts are accessible from front or top of UPS. Cable entries are accessible from
bottom. A 1m free space on all sides should be allowed during installation. Once the system is
installed it may be placed close to walls as long as free space is allowed for system doors to open.
(Per applicable national and/or local codes.)
For ventilation and service purposes allow for free space of minimum 1m above the unit or per
national and/or local codes and in front of UPS. Never install systems in direct sunlight.
NOTICE!
For reliability reasons do not stand on the UPS. keep the UPS cabinet surface free of any objects.
3.1.1 Cabinet Dimensions H*xWxD - 1400xWx800 [mm]. Width as in below table:
* H is 1500 mm for optional IP31 cabinets
Width
Without
Batteries
[mm]
UPS
Width With Built-in Batteries
[mm]
Width for Separate
Battery Cabinets
[mm]
1xBP I*
2xBP I*
3xBP I*
1xBP II**
1xBP III***
10kW
600
600
800
1000
1x800
1x1000
20kW
600
600
800
1000
1x800
1x1000
40kW
600
1x800
1x1000
1000
* BP I = Battery Pack I = 1 x 64 x 7 Ah batteries
** BP II = Battery Pack II = 1 x 64 x 24Ah batteries
*** BP III = Battery Pack III = 1 x 64 x 38 Ah batteries
990-4050
8
Installation Guide APC Silcon 10-40kW 400V UPS
Installation
Cabinets
1400 mm
1400 mm
1400 mm
10-20kW
with 3xBP l
10-20kW
with 2xBP l
10-20kW
with 1xBP l
600 mm wide
1000 mm wide
1400 mm
1400 mm
1000 mm wide
800 mm wide
600 mm wide
40kW
without batteries
40kW with 2xBP l
800 mm wide
APC Isolation
Transformer module
10-80kW
1000 mm wide
1400 mm
1400 mm
1400 mm
600 mm wide
Battery cabinet
for 1xBP ll
Battery cabinet
for 1xBP lll
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
9
Installation
3.2
Footprint
3.2.1 600mm UPS Cabinet with 1xBP I or Isolation Transformer
Power cable entry
Rear
Com. cable
entry
Front
3.2.2 800mm UPS Cabinet with 1xBP I or Built-in Isolation Transformer, or 2xBP I
Power cable entry
Rear
Com. cable
entry
Front
990-4050
10
Installation Guide APC Silcon 10-40kW 400V UPS
Installation
3.2.3 1000mm Cabinet for 10-20kW UPS with 3xBP I
Power cable entry
Rear
Com. cable
entry
Front
3.2.4 600mm Cabinet for 40kW UPS without Batteries
Power cable entry
Rear
Com. cable
entry
Front
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
11
Installation
3.2.5 1000mm Cabinet for 40kW UPS with 2xBP I
195
Com. cable entry
0
Power cable entry
Rear
Front
990-4050
12
Installation Guide APC Silcon 10-40kW 400V UPS
External Connection
4.0 External Connection
4.1
Connecting the UPS
4.1.1 Connecting the 10-20kW UPS
CAUTION!
At a switch mode load of 100% the neutral must be rated for 200% output phase current
CAUTION!
This UPS unit is an EN 50091-2 product and may cause radio interference in a domestic
environment. Take preventive measures if necessary.
Optional
Inp
ut
Ext. batteries
optional
t
tpu
Ou
System Integration Interface
Relay Board (Optional)
Communication Interface
Parallel Controller Board
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
13
External Connection
NOTICE!
Check correct phase rotation of mains input voltage!!
Max. input/output cables: 35mm2.
If there is no neutral input Dzn0 or Dyn11 input isolation transformer is required.
UPS
External
Input Fuses*
FM [A]
380-415V
External
Input Cable
[mm2]
380-415V
External PE
Cable [mm2]
Maximum
External
Output
Fuses*
[A]
External
Output Cable
[mm2]
10kW
20
4
4
16
2.5
20kW
40
10
10
32
6
* DIN gL types
NOTICE!
All cable dimensions are recommended sizes only.
Refer to local legal regulations.
UPS
External Alarm
Cable max.
[mm2]
External System
Earth Cable
[mm2]**
External Battery
Breaker
[A]
External
Battery Cable
[mm2]
10kW
2
4
25
4
20kW
2
4
50
10
PVC cables isolated to withstand ambient temperature of max. 30oC
** Must be rated as external PE cable if mains system is not supplying PE
NOTICE!
If an MCCB is used instead of external input fuses, the MCCB load capacity must be 8xIn
(nominal current) for min. 10ms.
990-4050
14
Installation Guide APC Silcon 10-40kW 400V UPS
External Connection
NOTICE!
Install gland plate in bottom of unit
4.1.2 Connecting the 40kW UPS
CAUTION!
At a switch mode load of 100% the neutral must be rated for 200% output phase current.
CAUTION!
This UPS unit is an EN 50091-2 product and may cause radio interference in a domestic
environment. Take preventive measures if necessary.
Optional
ut
Inp
Ou
tpu
t
Parallel Controller
Please refer to 8.5
System Integration interface
Communication Interface
Relay Board (Optional)
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
15
External Connection
NOTICE!
Check correct phase rotation of mains input voltage!!
Max. input/output cables: 120mm2. Battery: 70 mm2.
If there is no neutral input Dzn0 or Dyn11 input isolation transformer is required.
UPS
External
Input
Fuses* FM
[A]
380-415V
External
Input Cable
[mm2]
380-415V
External PE
Cable
[mm2]
Maximum
External
Output
Fuses*
[A]
External
Output
Cable
[mm2]
40kW
80
25
16
63
16
* DIN gL types
NOTICE!
All cable dimensions are recommended sizes only.
Refer to local legal regulations.
UPS
External Alarm
Cable max.
[mm2]
External System
Earth Cable
[mm2]**
External Battery
Breaker
[A]
External
Battery Cable
[mm2]
40KW
2
10
63
16
PVC cables isolated to withstand ambient temperature of max. 30oC.
** Must be rated as external PE cable if mains system is not supplying PE.
NOTICE!
Install gland plate in bottom of unit.
990-4050
16
Installation Guide APC Silcon 10-40kW 400V UPS
External Connection
4.2
System Integration Interface
NOTICE!
Consistent use of designations (Q001, Q002, Q003, H002, H003) in diagrams simplifies
information exchange.
System Integration Interface (SII) is the control link between UPS and system main switches
as shown in above diagram. The purpose of the SII is to ensure correct operation of switches
without losing system output power.
Auxiliary contacts on the main switches transmit the SII board inputs. Lamps on Service
Bypass Panel and Battery Breaker Box/Battery Cabinet indicate “green light” for operation of
output switches.
SII board also integrates input facilities for emergency shut-down and temperature
compensation of charge voltage for external battery (use with battery monitor). “Battery
operation” and “Common fault” are two main SII board status relay signals.
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
17
External Connection
4.2.1 Connections
Blue
Brown
990-4050
18
Installation Guide APC Silcon 10-40kW 400V UPS
External Connection
Terminal Blocks: X003/X004 (Anxiliary Contacts)
When switching Q001, Q002, Q010, Battery Breaker 1 or Battery Breaker 2 from “ON or 1” to
“OFF or 0”, the anxiliary contact has to be open BEFORE the corresponding main contacts are
opened. When switching Q001, Q002, Q010, Battery Breaker 1 or Battery Breaker 2 the
opposite way from “OFF or 0” to “ON or 1”, the anxiliary contact has to close with a maximum
delay of 0.5 seconds from the time the corresponding main contacts are closed.
• This type of auxillary contact is called a “late make” contact. (This also means that it will
“break early” when activated in opposite direction.)
• This auxillary contact is also called “NORMALLY OPEN” (NO), because the auxillary
contact will be open when the main contacts are open.
• Please note that the above term “NORMALLY” has nothing to do with NORMAL UPS
OPERATION MODE.
When switching Q003 from “OFF or 0” to “ON or 1”, the anxiliary contact has to open BEFORE
the corresponding main contacts are closed. When switching Q003 the opposite way from “ON
or 1” to “OFF or 0”, the auxillary contact has to close with a maximum delay of 0.5 seconds from
the time when the corresponding main contacts are opened.
• This type of anxiliary contact is called an “early break” contact. (This also means that it will
“make late” when activated in the opposite direction.)
• The auxiliary contact is also called “NORMALLY CLOSED” (NC), because the auxiliary
contact will be closed when the main contacts are open.
• Please note that the above term “NORMALLY” has nothing to do with NORMAL UPS
OPERATION.
X005 (Output Relays)
Battery operation signals are received with a 30-second delay. This function is inactive during
battery test. Common fault relay facility is programmable (standard factory setting: 10 sec.)
See APC Silcon User Guide for details.
Maximum nominal voltage on contact circuits is 277VAC. If two different phases are involved,
maximum phase to neutral voltage should be below 160VAC. Please note that phase L1 is
already present on the System Integration Interface board, supplied from the Service Bypass
Panel. Therefore, if a phase is needed for alarm or signal purposes, Phase L1 should be used.
4.3
Parallel Board
CAUTION!
Control cables must be separated from AC and DC power cables.
Parallel Board
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
19
External Connection
The built-in parallel board connects two or more UPS systems in parallel, either to obtain
increased system reliability or to obtain higher output power. The parallel board also ensures
correct load-sharing between paralled systems.
NOTICE!
For reliability reasons, APC recommends separate battery packs in redundant/parallel
conigurations.
To prepare the UPS for parallel/redundant mode, disconnect all sources of AC and DC power
supply to the UPS and connect the ribbon cable from the parallel board to the main controller
board (the ribbon cable is delivered with the UPS).
CAUTION!
DO NOT connect ribbon cable between controller and parallel card in single configurations.
Ribbon cable is for parallel operation only.
Complete the parallel system set-up by connecting the external control cables (see below).
Follow the instructions in the “Programming Parameters for Advanced Parallel” section of this
guide to execute necessary re-programming.
990-4050
20
Installation Guide APC Silcon 10-40kW 400V UPS
External Connection
Parallel Board
X021:15-pin SUB-D female
X020:15-pin SUB-D female
External multicore cable with 14 wires + shield
to other parallel units
UPS 1
UPS 2
UPS 3
External Control Cables
External multicore cable is equipped with 15-pin SUB-D plug at either end. Connect pin 1 to
pin 1, and pin 2 to pin 2 etc. up to pin 15 - with the exception of pin 8, which is not to be
connected.
Shield is connected to plug cover at both ends.
Terminals X020 and X021 for control cables located on parallel board. Connect X020 in UPS1
to X021 in UPS2, and connect X020 in UPS2 to X021 in UPS3 etc. Connect X020 in last UPS
to X021 in UPS1.
Cable is delivered with the UPS.
Power Cables
To optimize load-sharing in parallel operation, external power circuits must be “symmetrical”:
Power input and output cables to have same length and identical cross-sections.
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
21
External Connection
4.4
Communication Interface Board
The 3-port ComInterface is used to establish an interaction between UPS and e.g. a computer
system. Main purpose: To ensure a controlled computer shut-down in case of a mains supply
failure.
4.4.1 Connections
.
.
990-4050
22
Installation Guide APC Silcon 10-40kW 400V UPS
External Connection
4.5
Connecting of APC Silcon Tripel Chassis
The enclosed Triple Chassis must be connected to the serial port on the Communication
Interface Board, and to the 24V supply (cables included). Terminal locations shown below.
23.62 inch/600mm Cabinet
Serial ports
Front view of UPS Cabinet (doors open)
X50 is a 24V supply for Triple Chassis.
Only to be used for this purpose.
Not suitable for telephone equipment.
Triple Chassis must be connected to both
X50 and a serial port.
APC Silcon Triple Chassis
For more information please refer to the following section.
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
23
External Connection
4.6
APC Silcon Triple Chassis
The APC Silcon Triple Chassis (AP9604S) is an American Power Conversion (APC) external
management peripheral that allows you to use monitoring and control management
peripherals with your APC Silcon series UPS. The retrofit model (AP9604SR) is for use with
Silcon series UPSs that are not equipped with a 24 VDC power port.
4.6.1 Safety Warnings
Use the APC Silcon Triple Chassis only in conjunction with an APC Silcon UPS.
Do not connect a computer to any APC Silcon Triple Chassis port using a straight-through
extension cable. Use the communications cable provided with the APC Silcon Triple Chassis.
Connections using a cable made by any other manufacturer may cause damage or improper
operation of the APC Silcon Triple Chassis, the UPS, or the computer.
4.6.2 Product Description
➊
➍
➋
➌
1 Monitoring port
3 Status LED
2 To UPS port
4 Optional Power port
4.6.2.1Monitoring Port
The Monitoring port has two functions:
• Connecting to a terminal for configuration of the chassis. For direct connection to the
Monitoring port, you must use the Monitoring cable supplied with the chassis (APC
P/N 940-0024C).
• Connecting to other APC external management peripherals in a daisy chain.
4.6.2.2To UPS Port
The “To UPS” port connects the chassis to the UPS, using the Silcon UPS cable (APC P/N 9400071). The cable connector plugs into a communications port on an APC Silcon UPS.
990-4050
24
Installation Guide APC Silcon 10-40kW 400V UPS
External Connection
4.6.2.3LEDs
The APC Silcon Triple Chassis status LED provides important information concerning
operation of the chassis. Refer to the table below for a description of the conditions indicated
by the LED.
IF the LED is…
THEN the Silcon Triple Chassis…
off
is not receiving power.
flashing quickly
(5 times per second)
has not been configured. See the APC Silcon Management Quick
Start Guide provided with your chassis or the Web/SNMP
Management Card Installation Guide on the CD for more
information.
flashing slowly
(1 time per second)
is powered on but is not communicating with the UPS.
on
is operating normally.
4.6.2.4Optional Power Input
With the Optional Power input, you can power the APC Silcon Triple Chassis from an external
source, using a 24 VDC power adapter. A universal adapter (AP9505i) or a standard adapter
(AP9505) can be purchased separately from APC.
4.6.3 Installing Management Peripherals
There are two basic types of APC management peripherals that work with the APC Silcon
Triple Chassis:
• Management peripheral cards, which fit into external management peripherals that
are equipped with a card slot.
• External management peripherals, which connect to the Monitoring (or Advanced)
port of other external management peripherals.
NOTICE!
The name “Monitoring” port varies from product to product, but its purpose is the same – to
replicate the UPS communications port.
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
25
External Connection
4.6.3.1Order of Management Peripheral Cards
Because UPS signals are passed between management peripherals, you must install
management peripheral cards in the correct order for them to work together properly. The card
slots are numbered 1 to 3, from left to right, as viewed from the rear of the chassis. The
following table lists the management peripheral cards, their priority, and proper position.
Management
Peripheral Card
P/N
Priority
Position
Web/SNMP Management
AP9606
Card
Highest
High-numbered slot
Out-of-Band
Management Card
(Call-UPS® II)
AP9608
Second-highest
Interface Expander
AP9607
Second lowest
Environmental
Monitoring Card
(Measure-UPS® II)
AP9612T
AP9612TH
Lowest
Low-numbered slot
4.6.3.2Installing Management Peripheral Cards
To install management peripherals, perform the following steps.
1) Make sure that the chassis is powered off.
2) Install management peripheral cards into the housings on the rear of the chassis. See the
instructions supplied with the cards and the table above.
3) If you are daisy-chaining other APC external management peripherals to the APC Silcon
Triple Chassis: Connect the UPS cable (supplied with the management peripheral) to the
Monitoring port of the chassis and to the “To UPS” port of the other management peripheral
(Share-UPS, MasterSwitch, etc.). See “Daisy-chaining the APC Silcon Triple Chassis”.
4) Power the APC Silcon Triple Chassis and all external management peripherals.
NOTICE!
If your configuration requires additional power, connect a 24V AC/DC power adapter available
from APC (part number AP9505 or AP9505i) for all models of Triple Chassis.
4.6.3.3Daisy-chaining the APC Silcon Triple Chassis
If you need more than the three card slots available with the APC Silcon Triple Chassis, or if
you want to use other external management peripherals, you can daisy-chain external
management peripherals together, provided that the total amperage of all installed
management peripherals — cards and external — does not exceed the supplied amperage. (See
“Determining Power Requirements:”).
NOTICE!
When daisy-chaining Triple Chassis units, you may need to use a power adapter.
990-4050
26
Installation Guide APC Silcon 10-40kW 400V UPS
External Connection
To add card slots, you can daisy-chain the APC Silcon Triple Chassis with the standard Triple
Chassis (AP9604) management peripheral, installing the APC Silcon Triple Chassis closer to
the UPS.
4.6.4 Powering the APC Silcon Triple Chassis
The APC Silcon Triple Chassis supplies power to the installed management peripheral cards
and to the Monitoring port, allowing you to power multiple management peripherals.
4.6.4.1AP9604S Power Considerations
The AP9604S model of the APC Silcon Triple Chassis receives its power from the UPS through
the power connector of the Silcon UPS cable. If the total current required by all the installed
management peripherals exceeds 500 mA, you must use a 24 VDC power adapter. To find out
whether you need additional power, see “Determining power requirements”.
4.6.4.2Power Adapters
APC offers two models of 24 VDC power adapter.
• The standard adapter (AP9505) can provide an additional 400 mA.
• The universal adapter (AP9505i) can provide 850 mA.
4.6.4.3Using a Power Adapter
To use the adapter, plug it into a protected power outlet and into the Optional Power port of
the APC Silcon Triple Chassis.
NOTICE!
If the power adapter loses power because of a UPS shutdown, its attached management
peripherals may not operate properly, thus adversely affecting the UPS and its protected
equipment.
4.6.4.4AP9604SR Power Considerations
The AP9604SR model receives its power from the UPS through the supplied 24 VDC universal
adapter. The total current required by your management peripherals must not exceed the 850
mA limit of the power adapter. See ““Determining power requirements”.
4.6.4.5Determining Power Requirements:
To determine the total amount of current required by your management peripherals, add the
individual current requirements for each management peripheral to be installed with the APC
Silcon Triple Chassis to the current requirements of the chassis itself. Refer to this table
Part #
Management Peripheral
Draw (mA)
AP9207
Share-UPS 8-port Interface Expander
65
AP9600
Expansion Chassis
30
AP9604
Triple Chassis
20
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
27
External Connection
AP9604S[R]
APC Silcon Triple Chassis
90
AP9606
Web/SNMP Management Card
110
AP9607
Interface Expander
45
AP9608
Out-of-Band Management Card
(Call-UPS II)
35
AP9612
Environmental Monitoring Card (Measure-UPSII)
60
AP9825i
Isolated Extension Cable
50
AP9830
Remote Power-Off Device
35
4.6.5 Troubleshooting
The following table shows the solution to common problems with the operation of the Triple
Chassis
Problem
Possible Cause
Solution
Status LED is off
The chassis is not
receiving adequate
power.
See “Powering the APC Silcon
Triple Chassis”, and verify that you
are not exceeding current
requirements.
Status LED is flashing
quickly
The chassis has not been
configured.
Configure the Silcon Triple
Chassis. See the APC Silcon
Management Quick Start Guide
provided with your chassis or the
Web/SNMP Management Card
Installation Guide on the CD for
more information.
Status LED is flashing
slowly
The chassis is not
communicating with the
UPS.
Verify that the supplied UPS cable
is properly connected to the Triple
Chassis and to a communications
port on the UPS.
Attached management
peripheral cannot
identify UPS model or
nominal output voltage.
The management
peripheral firmware
does not support 3-phase
UPSs.
You may be able to upgrade the
firmware of the management
peripheral. Call APC Customer
Support.
4.6.5.1If Problems Persist
For problems not covered in the troubleshooting chart or for persistent problems, follow this
procedure:
1) Note the serial number and date of purchase of the APC Silcon Triple Chassis. Contact APC
Customer Support at the phone number or address that is listed in this manual.
2) Be prepared to provide a description of the problem. A technician will help solve the
problem over the phone, if possible, or will give you a return material authorization (RMA)
number.
3) If the APC Silcon Triple Chassis is under warranty, repairs are free of charge. If the
warranty has expired, there will be a nominal charge for repair.
990-4050
28
Installation Guide APC Silcon 10-40kW 400V UPS
External Connection
4) Pack the APC Silcon Triple Chassis carefully in its original packaging, if possible. Do not
use polystyrene beads for packing. Damage sustained in transit is not covered under the
warranty. Enclose a letter in the package with your name, address, RMA number, a copy of
the sales receipt, daytime phone number, and payment (if applicable).
5) Mark the RMA number clearly on the outside of the shipping carton. The factory will not
accept any materials without this marking.
6) Return the Triple Chassis by insured, prepaid carrier to the address given to you by APC
Customer Support.
4.6.6 Product Specifications
4.6.6.1Monitoring Port Pin Assignments
The Monitoring port is a 9-pin communications port. The port operates with no flow control at
a rate of 2400 baud. The data format is 8 data bits with 1 start bit, 1 stop bit, and no parity.
When the Triple Chassis operates with simple signalling, the following limitations and
capabilities apply to the Monitoring port:
• Pins 3, 5, and 6 are open collector outputs which must be pulled up to a common
referenced supply no greater than +40 VDC. The transistors are capable of a noninductive load of 25 mA. Use only Pin 4 as the common.
• The output at Pin 2 generates a low-to-high RS-232 level when the device is
signalling an On Battery condition. The pin is normally at a low RS-232 level.
• The UPS is signalled to shut down when a high RS-232 level is applied to Pin 1 for
4.5 seconds. Shutdown is also dependent on the UPS status.
When the Triple Chassis operates with advanced signalling, the following limitations and
capabilities apply to the Monitoring port:
• Pin 7 is unassigned.
• DC operating voltage is available on Pin 8. This voltage may be from the UPS or from
an external adapter, whichever is greater.
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
29
External Connection
Normally Open
Line Fail Signal
Normally Open
Low Battery Signal
Normally Closed
Line Fail Signal
Common
UPS Shut Down RS-232 Input or
Advanced Mode RS-232 Data RX In
Line Fail RS-232 Output or
Advanced Mode RS-232 Data TX Out
Unregulated
+24 VDC Output
Chassis
990-4050
30
Installation Guide APC Silcon 10-40kW 400V UPS
External Connection
4.6.6.2Power, Physical, and Environmental Specifications.
Item
Specification
Power
Turn on voltage:
> 22 VDC
Turn off voltage:
< 16 VDC
Current draw (normal operation):
90 mADC
Current draw
(voltage < 16 VDC):
< 1 mADC
Physical
Size (H xW x D):
1.75 x 17.0 x 5.0 in
(44 x 432 x 127 mm)
Weight:
4.02 lb (1.81 kg)
Shipping weight:
8.12 lb (3.65 kg)
Environmental
Elevation (above MSL):
Operating
Storage
0 to 10,000 ft (0 to 3000 m)
0 to 50,000 ft (0 to 15 000 m)
Temperature:
Operating
Storage
32 to 113˚F (0 to 45˚C)
-4 to 158˚F (-20 to 70˚C)
Relative humidity:
Operating
Storage
0 to 95%, non-condensing
0 to 95%, non-condensing
Electromagnetic immunity:
FCC Class A
EN50082-1 verified
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
31
External Connection
4.7
APC Silcon Battery Cabinets
IMPORTANT SAFETY INSTRUCTIONS
a
The installation of battery drawers in UPS cabinets requires battery knowledge and should be
made or supervised by qualified personnel only. Keep unauthorized personnel away from
batteries.
b
Use identical battery types and numbers when replacing batteries. See battery supplier
manual for further details.
c
CAUTION - Do not dispose of batteries in a fire. Battery may explode.
d
CAUTION - Batteries are fully charged on delivery. Do not short battery terminals or DC
terminals.
e
CAUTION - Avoid rough treatment and opening of batteries. Released electrolyte is harmful
to skin and eyes and may be toxic.
f
CAUTION - Batteries may cause electric shocks and high voltage short-circuit current. Follow
below precautions when working with batteries:
1
Remove watches, rings and other metal objects.
2
Use tools with insulated handles.
3
Wear rubber gloves and boots.
4
Do not leave tools or metal parts on top of batteries.
5
Disconnect charging source prior to connecting batteries.
Installation and use of this product must comply with all national, federal, state, municipal or
local codes. If you need assistance, please have your UPS model and serial number ready and
call APC, see “How to Contact APC” in this guide.
For more information on the APC World Wide Web site at http://www.appc.com.
WARNING!
The entire system contains HAZARDOUS AC/DC VOLTAGES from several power sources.
Some terminals and components are live even with the system being switched off!
ONLY qualified electricians should carry out installations according to national and local codes.
NO UPS types may have built-in batteries when connected to external batteries!
NEVER install batteries not complying with APC specifications. Failing that, the installer takes
over full responsibility!
NEVER lift or transport connected or installed batteries.
NOTICE!
For reliability reasons do not stand on the UPS. keep the UPS cabinet surface free of any objects.
990-4050
32
Installation Guide APC Silcon 10-40kW 400V UPS
External Connection
4.7.1 Cabinets
UPS with Built-in Batteries
4.7.2 Preparing Batteries
CAUTION!
Battery drawer weighs approx. 22 kg with batteries.
The 12V, 7.2 Ah batteries are glued to drawer plate.
Battery drawers present a risk of electric shocks. Prior to installation of battery drawers, remove
conductive jewellery such as chains, watches and rings. High-voltage short-circuits through
conductive materials may cause severe burns.
Do not install battery drawers in UPS frame until all AC/DC sources are disconnected.
If battery drawers need to be stored for extended periods, store in a dry, cool environment.
Keep battery drawers in an upright position.
Do not stack more than 3 cardboard-wrapped battery drawers on top of each other.
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
33
External Connection
Battery drawers are wrapped in cardboard and delivered on pallets.
Unpack battery drawers, checking that type, number and size comply with the order.
Connect wire as shown below:
990-4050
34
Installation Guide APC Silcon 10-40kW 400V UPS
External Connection
800mm Battery Cabinet
1000mm Battery Cabine
4.7.3 Mounting Batteries
WARNING!
Open front door of UPS and unscrew front cover.
Do not install battery drawers in UPS frame until all AC/DC sources are disconnected.
Disconnect charging source prior to connecting batteries. Ensure that battery breakers F001 and
F002 are set to position “off”.
WARNING!
Before proceding, ensure that power supplies have been disconnected from UPS for a minimum
of 5 minutes.
Unscrew front frame of UPS and slide frame down as shown above.
Battery drawers may be installed after removal of front cover.
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
35
External Connection
Check all battery connections to ensure that proper contact is established.
Insert battery drawers in
the APC Silcon UPS
Connect all battery drawers to the
terminal on the left side of the column
990-4050
36
Installation Guide APC Silcon 10-40kW 400V UPS
External Connection
4.7.4 Final Checks
CAUTION!
Follow the “start-up procedure” in APC Silcon User Guide.
IMPORTANT SAFETY INSTRUCTIONS
a) The servicing of batteries requires battery knowledge and should be carried out or supervised
by qualified personnel only. Keep unauthorized personnel away from batteries.
b) Use only R/C (BAZR2) batteries in UPS systems with built-in batteries.
Max. battery length: 152mm
Max. battery width: 67mm
When mounting batteries allow for at least 0.2inch/0.5mm between batteries and also
between batteries and battery shelf.
c) CAUTION - Batteries are fully charged on delivery. Do not short battery terminals or DC
terminals.
d) CAUTION - Do not dispose of batteries in a fire. Batteries may explode.
e) CAUTION - Avoid rough treatment and opening of batteries. Released electrolyte is harmful
to skin and eyes and may be toxic.
f) CAUTION - Batteries may cause electric shocks and high voltage short-circuit current.
Follow the precautions below when working with batteries:
1
Remove watches, rings and other metal objects.
2
Use tools with insulated handles.
3
Wear rubber gloves and boots.
4
Do not leave tools or metal parts on top of batteries.
5
Disconnect charging source prior to connecting or disconnecting batteries.
6
Determine if the battery is inadvertently grounded. If inadvertently grounded, remove
unwanted source of ground. Any contact with grounded battery may result in electric
shocks. The likelihood of such shocks will be reduced if grounds are removed during
installation and maintenance (applicable to a UPS and a remote battery supply without
grounded supply circuit).
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
37
External Connection
4.7.5 APC Silcon Battery Cabinets
Battery Cabinet
UPS
IMPORTANT SAFETY INSTRUCTIONS
a) The servicing of batteries requires battery knowledge and should only be carried out by
qualified electricians familiar with batteries. Keep unauthorized personnel away from
batteries.
b) Use identical battery types and numbers when replacing batteries. See battery supplier
manual for further details.
c) CAUTION - Batteries are fully charged on delivery. Do not short battery terminals or DC
terminals.
d) CAUTION - Do not dispose of batteries in a fire. Batteries may explode.
e) CAUTION - Avoid rough treatment and opening of batteries. Released electrolyte is harmful
to skin and eyes, and may be toxic.
f) CAUTION - Batteries may cause electric shocks and high voltage short-circuit current.
Follow the precautions below when working with batteries:
1.
Remove watches, rings and other metal objects.
2.
Use tools with insulated handles.
3.
Wear rubber gloves and boots.
4.
Do not leave tools or metal parts on top of batteries.
5.
Disconnect charging source prior to connecting batteries.
6.
Determine if the battery is inadvertently grounded. If inadvertently grounded, remove
unwanted ground source. Any contact with grounded batteries may result in electric
shocks. The likelihood of such shocks will be reduced if grounds are removed during
installation and maintenance.
Installation and use of this product must comply with all national, federal, state, municipal or
local codes. If you need assistance, please have your UPS model and serial number ready and
call APC, see the section “How to contact APC” in this guide.
Find more information on the APC World Wide Web site at http://www.appc.com.
990-4050
38
Installation Guide APC Silcon 10-40kW 400V UPS
External Connection
WARNING!
The entire system contains HAZARDOUS AC/DC VOLTAGES from several power sources.
Some terminals and components are live even with the system being switched off!
ONLY qualified electricians may install batteries and national and local codes must be followed.
NO APC Silcon UPS may have built-in batteries if connected to external batteries!
NEVER install batteries not complying with APC specifications. Falling that, the installer takes
over full responsibility!
NEVER lift or transport connected/installed batteries.
4.7.5.1Installation of Batteries
See Installation Guide for Battery Cabinet for:
• Preparing Batteries and UPS
• Dimensions and Weight
• Connecting Batteries
WARNING!
Before proceding, ensure that power supplies have been disconnected from UPS for a minimum
of 5 minutes.
CAUTION!
Follow “Start-up Procedure” in APC Silcon User Guide.
Diagram - UPS with
Battery Cabinet
System Integration Interface
APC
UPS
Silcon
Battery Breaker trip for EPO
(Emergency Power Off)
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
39
External Connection
4.8
Battery Breaker Box/Fuse-box
CAUTION!
Batteries connected to a UPS out of service for a period exceeding 8 days may be damaged.
Refer to Section 7.0 Power Disconnection in this guide.
Battery Breaker Box/Fuse-box provides overcurrent and short-circuit protection for UPS
installations with external batteries.
NOTICE!
If battery has been disconnected, refer to Section: - UPS Start Up in the APC Silcon User Guide.
APC
Battery Breaker
Box
APC Silcon UPS
Battery
990-4050
40
Installation Guide APC Silcon 10-40kW 400V UPS
External Connection
4.8.1 Battery Breaker Box
UPS
Ampere
Rating
[A]
Connection
Cable
[mm2]
Max.
shortcircuit
current [kA]
Dimensions
HxWxD [mm]
Weight
[kg]
10 kW
20 kW
40 kW
25
50
63
4
10
16
10
10
10
540x540x183
504x540x183
540x540x183
20
20
20
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
41
External Connection
UPS
Battery 2
UPS
Battery 1
Battery 2
Battery 1
4.8.2 Battery Breaker Box Connection Diagram
Main cables are connected directly
to component terminals
X009 LED signal from UPS “OK to operate corresponding MCCB”
X010 MCCB position signals for UPS
X011 Trip for emergency stop (220-240V AC)
990-4050
42
Installation Guide APC Silcon 10-40kW 400V UPS
External Connection
4.8.3 Fuse-box
UPS
Ampere Rating
[A]
Connection
Cable [mm2]
Max.
short-circuit
current [kA]
Dimensions
HxWxD [mm]
Weight
[kg]
10 kW
20 kW
40 kW
25
50
63
4
10
16
10
10
10
540x540x183
504x540x183
540x540x183
20
20
20
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
43
External Connection
UPS
Battery 2
UPS
Battery 1
Battery 2
Battery 1
4.8.4 Fuse-box Connection Diagram
X009 LED signal from UPS “OK to operate corresponding fuse.”
X010 Released fuse signal for UPS
990-4050
44
Installation Guide APC Silcon 10-40kW 400V UPS
External Connection
4.8.5 UPS with External Battery in Battery Breaker Box/Fuse-box Configuration
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
45
Programming Parameters
5.0 Programming Parameters
Below table shows operating parameters programmable from keyboard. Only qualified users
should re-set programming parameters.
5.1
Parameters
Parameter
Setting*
Comments
Bypass operation
YES, NO
YES will switch the system into bypass mode
Language
GB, D, F
DK, S, SF
NL, PL, CZ
E, P, SK, H
Language of text in display
Autostart
YES, NO
Automatic restart by mains return
(1 min.delay). Ensures quick battery recharge
Remote shutdown active
YES, NO
Shutdown of UPS by remote signal when in
battery operation. Saves battery energy
Remote shutdown
HIGH, LOW
Nature of remote shutdown signal level
Remote shutdown time
0, 1, 2, 3, 4
5, 6, 7, 8, 9
10 min.
Time delay on remote shutdown of UPS
Battery capacity test
---
Initiates back-up time check.
Time measured from start until it reaches low
DC warning level.
(See User Guide section 6 )
Battery monitor test**
---
Initiates checks of battery condition by 25%
discharging
Automatic battery test**
OFF, 3, 6 months
Activates the battery monitor test in cyclic
intervals
Battery monitor reset**
---
Press the
and
key
to resets alarm (flashing light)!
*
Boost charge
YES, NO
YES results in boost charge (10 hours)
Autoboost charge
YES, NO
YES results in boost charge after battery
operation. (10 hours)
Enter new date
YYMMDD
Set tolocal date
Enter new time
HHMMSS
Set to local time (24 hour clock)
Factory settings in bold
** Only for systems with Battery Monitor active
*** Do not leave system running in bypass mode (Static bypass) for extended periodes of time,
as batteries are not recharged in bypass mode.
990-4050
46
Installation Guide APC Silcon 10-40kW 400V UPS
Programming Parameters
5.1.1 Programming Keys
NOTICE!
Display accuracy is + 1%, + digit.
Scrolls up
through list
Scrolls down
through list
Displays time
Stores
parameters/
enter parameter
stack
Exits a mode
Silences the
audible alarm
Accesses
alarm stack
Chooses parameters
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
47
Programming Parameters
5.1.2 Programming Example - Switch to Bypass Operation
NOTICE!
Do not leave in by-pass mode for extended periods in order not to affect battery capacity.
Return to normal operation
Follow same procedure to program other parameters.
5.2
System Configuration
System configuration parameters are vital for correct system operation and are passwordprotected.
CAUTION!
Incorrect programming may damage battery or cause output voltage to be lost during operation!
990-4050
48
Installation Guide APC Silcon 10-40kW 400V UPS
Programming Parameters
System Configuration Parameters (password protected)
Parameter
Setting*
Comments
Isolation Transformer Input
YES, NO
YES if optional input isolation transformer is available
IsolationTransformer
Output
YES, NO
YES if optional output isolation transformer is available
Delta Soft Start Time
1, 10, 20, 40 sec.
Input current switching in ramp function. Use higher
values for smaller/unstable diesel generators
External SSW present
YES, NO
YES for systems with external static bypass switch
Normal Charge Voltage
410-460V
438V
Setting of float charge voltage at 20°C
(Automatic compensation for temperature deviations)
Boost Charge Voltage
438-460V
438V
Setting of boost charge voltage at 20°C
(Automatic compensation for temperature deviations)
Low Battery warning
336-384V
336V
Discharged Battery warning
Low Battery shut-down
310-336V
326V
Switches off system at min. permissible battery
voltage
Synchronization
0.25, 0.5, 1, 2, 4
Hz/sec.
Syncronization speed.
High Battery Temperature
15-40°C
35°C
Alarm - Ambient temperature for battery too high
Common fault delay
0, 10, 20,
30 sec.
Delay before common fault alarm relay is activated
Reset operation mode lock
YES, NO
YES resets system locked in bypass or battery
operation mode caused by system failures (only
applicable for service personnel)
Expected back-up time
(min.)
0.1-999.9
5.0
Expected UPS back-up time in minutes when running
at 100% ohmic load. Time used by ABM**
Battery Capacity in (Ah)
0.1-999.9
7.0
Total Battery capacity in Ah.
Setting used by ABM**.
Highest Station Address
2-9
Highest station address in parallel system
Station Address
1-9
Station address in parallel system
APM Mode Active
(Advanced Power
Management)
Disabled
Redundant +1
Parallel +1
Use only in parallel systems.
Disabled: Advanced power management off.
Redundant +1: Redundant operation with one unit
being inactive in parallel system
Parallel +1: Redundant operation with all units in
operation.
APM Test Mode Active
YES, NO
YES, if APM test mode is active
Battery Connection
Common,
Separate
Common: if common battery is used in parallel system.
Separate: if separate battery is used
* Bold text refers to factory standard setting
**Advanced Battery Monitor
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
49
Programming Parameters
5.2.1 Programming Example - Change Charge Voltage to 446
NOTICE!
Change charge voltages, battery warning limit, shut down voltage and high battery temperature
limit by entering the actual value. See example above.
990-4050
50
Installation Guide APC Silcon 10-40kW 400V UPS
Programming Parameters
5.2.2 Programming Example - Change to Output Isolation Transformer available
NOTICE!
Change parameters by pressing the
key once or several times. See example above.
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
51
Programming Parameters
5.3
Programming Parameters for Advanced Parallel Operation
To use the advanced parallel functions, the following parameters must be programmed:
1. “Station number”
2. “Highest station address”
3. “Advanced power management”
4. “APM test mode active”
5. “Battery connection”
5.3.1 Description of Settings
1. “Station number”
• Valid station numbers: 1-9 stating the UPS parallel address in system.
2. “Highest station number”
• Valid station numbers: 2-9 stating the number of UPSs in system.
3. “Advanced power management”
• “Disabled”: Advanced Power Management is inactive.
• “PARALLEL+1”: Advanced Power Management is activated when the system operates
as PARALLEL N+1, meaning that one system can be isolated without overloading the
remaining systems (N systems/UPSs).
• “REDUNDANT+1”: Advanced power management is activated when the system
operates as REDUNDANT N+1, meaning that one system can be isolated without
overloading the remaining systems (N systems/UPSs) with one spare system.
4. “APM test mode active”
• “No”: Stand-by-time will be 24 hours - on-line time will be 48 hours (xN systems).
• “Yes”: Stand-by-time will be 1 min. - on-line time will be 2 min (xN systems).
5. “Battery connection”
• “Separate”: Separate battery for this UPS.
• “Common”: Common battery in a parallel system.
NOTICE!
“Common”: Common battery in a parallel system. When this setting is chosen, the highest
battery temperature that can be found in the parallelled systems (for charge voltage
compensation).
NOTICE!
Common battery pack is a technical possibility.
However, APC recommend separate battery pack due to a higher safety degree in connection
with redundant/parallel operation.
The UPS system is designed for both situations.
990-4050
52
Installation Guide APC Silcon 10-40kW 400V UPS
Programming Parameters
5.3.2 Programming example
Example with four systems in parallel with separate batteries.
• Programme the station addresses 1-4: 1 for UPS 1, 2 for UPS 2, 3 for UPS 3, and 4 for
UPS 4.
• All UPS systems have to be programmed to “Highest station address”:4.
• If APM is not to be tested, “APM test mode active” must be “NO”.
• If a system is isolated due to service, the station numbers must be reprogrammed for the
remaining active systems starting with number 1 and ending with maximum. number
of active systems. No number must be left in this sequence. Furthermore, “Highest
station address” must be changed to number of active UPSs in parallel.
5.4
Battery Monitor
5.4.1 Installation of new batteries
To avoid false alarms, the above procedure MUST be followed.
NOTICE!
Contact your local dealer if you have any questions regarding changing parameters.
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
53
Options/Accessories
6.0 Options/Accessories
Please contact your local APC representative for information on options/accessories available
in your region. See “How to Contact APC” in this guide.
6.1
Service Bypass Panel for Single Operation
Fixing holes in rear of box
4 x ø 6.5mm:APC Service Bypass Panel
10/20kW & 40kW
4 x ø 6.5mm:APC Service Bypass Panel
60kW & 80kW
UPS
10kW
External
System
Input
Fuse
[A]
Max.
Prospective
ShortCircuit
Current
[kA]
System
Input/
UPS
Input
Cable
[mm2]
**
20
15
4
System
Output/
UPS
Output
Cable
[mm2]
**
2.5
Max.
External
Syste
m
Output
Fuse
[A]***
16
Max.
Cable
Size/
Stud
Size
Dimensions
HxWxD [mm]
Weight
[kg]
16
mm2
(E:M6)
315x305x
125(175*)
7
Fixing
Centres
AxB
[mm]
240x
240
20kW
40
15
10
6
32
16
mm2
(E:M6)
315x305x
125(175*)
7
240x
240
40kW
80
25
25
16
63
35
mm2
(E:M6)
315x400x
125(175*)
11
270x
330
990-4050
54
Installation Guide APC Silcon 10-40kW 400V UPS
Options/Accessories
***
If no external System Output fuses are available or if it has a higher value than
indicated above, System Output and UPS Output cables should be dimensioned as
System Input and UPS Input cables.
**
Sizes according to IEC 364-5-532 for PVC insulated copper cables (max. ambient
temperature: 30oC). Installation method B: Insulated conductors in wall conduit.
Also refer to local legal regulations.
Beware that single-phase Switch Mode Power supply loads will increase neutral
current! At a 100% SMPS load, neutral cable should be dimensioned for 200% of
phase current.
*
Main supply
Depth of enclosure includes switch handles
Load
APC Silcon UPS
Service
Bypass
Panel
O/P
I/P
SBP Signalling
10 x 0.75mm2 (max. 2mm2)
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
55
Options/Accessories
6.1.1 Wiring up UPS with SBP in TN-C-S Network
6.1.2 Wiring up UPS with SBP in TN-S Network
990-4050
56
Installation Guide APC Silcon 10-40kW 400V UPS
Options/Accessories
6.1.3 Operating The External Service Bypass Switch
Action
1. Press
on the keyboard
Display shows
2. Press
or
Bypass operation
:NO
3. Press
on the keyboard
4. Press
on the keyboard
on the keyboard until
Bypass operation
:YES
Lamp indication
on Service Bypass Panel
5. Check lamp indication on the Service Bypass Panel
The Green lamp (H003)
above the bypass switch
handle (Q003) lights
6. Turn the external bypass switch (Q003)
to position ”1“
The Green lamp (H002)
above the output switch
handle (Q002) lights
7. Turn the output switch (Q002) to position ”0“
Only the lamp (H002)
above the output switch
handle (Q002) lights now
Display shows
8. Open the front door and press both the green
”ON“ and the red ”OFF“ keys simultaneously
** System OFF **
The acoustic alarm sounds for 30 sec.*
9. Turn the input switch to position ”0“
The red alarm LED below the display lights
and the acoustic alarm sounds for 30 sec.
*
The acoustic alarm can be reset by the
key
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
57
Options/Accessories
6.1.3.1Switching from External Bypass to Normal UPS Operation
Action
Display shows
1. Turn the input switch (Q002) to position ”0“
** System OFF **
2. Open the UPS front door and press the
green "ON” key
Normal operation
load power %
3. Press
on the keyboard
4. Press
or
5. Press
on the keyboard
6. Press
on the keyboard
on the keyboard until
Bypass operation
:NO
Bypass operation
:
:YES
Lamp indication
on Servive Bypass Panel
7. Check lamp indication on the bypass panel
The Green lamp (H002)
above the output switch
handle (Q002) lights
8. Turn the output switch (Q002) to position ”1“
Now also the green lamp
(H003) above the bypass
switch handle (Q003)
lights
9. Turn the bypass switch (Q003) to position ”0“
Only the Green lamp
(H003) above the bypass
switch handle (Q003)
lights
Display shows
10. Press
on the keyboard
11. Press
or
12. Press
on the keyboard
Bypass operation
:NO
11. Press
on the keyboard
Normal operation
load power xx %
11. Press
on the keyboard
on the keyboard until
Bypass operation
:
:YES
No lamps on the Service
Bypass Panel light any
longer
990-4050
58
Installation Guide APC Silcon 10-40kW 400V UPS
Options/Accessories
6.2
Service Bypass Panel for Parallel Redundant Operation
Service Bypass Panel (SBP)
System Output
Q003
Mains Supply
Q004
Q002b Q002a
Q001a Q001b
X020
X021
Control
cables
APC Silcon
400V UPS
Battery Breaker/
Fuse Box
Battery
X020 APC Silcon
X021 400V UPS
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
59
Options/Accessories
6.2.1 Two Parallel Systems with Service Bypass Panel
990-4050
60
Installation Guide APC Silcon 10-40kW 400V UPS
Options/Accessories
6.2.2 Parallel/Redundant Operation with Service Bypass Panel and External
Battery via MCCB
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
61
Options/Accessories
6.2.3 Operating External Service Bypass Switch for Parallel Systems
6.2.3.1Bypassing Parallel UPS Systems
H002a
CAUTION!
Batteries connected to a UPS out of service for a period exceeding 8 days may be damaged.
990-4050
62
Installation Guide APC Silcon 10-40kW 400V UPS
Options/Accessories
Action
Step 1-4 can be carried out with any of the parallel systems, however this will switch
all systems into bypass operation.
Display shows
1. Press
on the keyboard
2. Press
or
3. Press
on the keyboard
4. Press
on the keyboard
Bypass operation
:NO
on the keyboard until
Bypass operation
:YES
Bypass operation
All systems will transfer to bypass operation
Do not switch off any of the UPS systems
until step 5-8 has been completed.
Lamp indication
on bypass panel
5. Check lamp indication on the Service Bypass Panel
The green lamp (H003)
above the bypass switch
handle (Q003) lights
6. Turn the external bypass switch (Q003)
to position ”1“
The green lamp (H004)
above the output isolator
(Q004 and the green lamps
(H002) above the output
switch handles (Q002) lights
7. Turn the output isolator (Q004) to position ”0“
The green lamps (H002)
above the output switch
(Q002) light and the green
lamp (H004) above the output
switch (Q004) lights
8. Turn the output switches (Q002) to position ”0“
Now the lamps (H002)
above the output switch
handles (Q002) light and the
green lamp (H004) above the
output switch (Q004) lights
Display shows
9. Open the front door and press both the green
”ON“ and the red ”OFF“ keys simultaneously in
any of the systems
The acoustic alarm sounds for 30 sec.*
Repeat for (all) other system(s).
** System OFF **
10. Turn all input switches (Q001) to position ”0“
The red alarm LED below the display lights
and the acoustic alarm sounds for 30 sec.
*
The acoustic alarm can be reset by the
key
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
63
Options/Accessories
6.2.3.2 Switching Parallel System from External Bypass into Normal UPS Operation
H002a
990-4050
64
Installation Guide APC Silcon 10-40kW 400V UPS
Options/Accessories
Action
Display shows
1. Check that output switch (Q004) is in
position “0”
2. Check that all output switches (Q002)
are in position “0”
3. Turn input switches (Q001) to position “1”
** System OFF **
4. Open the UPS front door and press the
green “ON” push-botton
Normal operation
load power 0%
5. Press
on the keyboard
6. Press
or
7. Press
on the keyboard
8. Press
on the keyboard
on the keyboard until
All systems will transfer to bypass operation
Bypass operation
:NO
Bypass operation
:YES
Bypass operation
Lamp indication
on Service Bypass Panel
9. Check that all output switches (Q002) are in
position “0”
10. Turn all output switches (Q002) to position ”1“
The green lamps (H002)
above all the output
switch handles (Q002)
lights.
The green lamp
(H004) above the output
switch (Q004) handle also
lights.
11. Turn the output switch (Q004) to position ”1“
The green lamps (H002)
above all the output switch
handles (Q002) light. The
green lamp (H004) above
the output switch (Q004)
handle and the green lamp
(H003) above the bypass
switch light.
12. Turn the bypass switch (Q003) to position “0”
The green lamps (H002)
and (H004) do not light any
longer. (H003) will light
until normal operation.
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
65
Options/Accessories
The following can be carried out on any UPS
Display shows
13. Press
on the keyboard
Bypass operation
:YES
14 Press
or
Bypass operation
:NO
15. Press
on the keyboard
16. Press
on the keyboard
on the keyboard until
All the systems will transfer to normal operation.
Normal operation
load power xx%
No lamps on the bypass
panel lights any longer
6.2.4 Isolating One UPS for Service/Maintenance
In a redundant system, one UPS may be isolated for service/maintenance without affecting
other UPSs.
1. Check that remaining UPS(s) is capable of carrying the load in the event that one UPS is isolated
2. Switch off system to be isolated for maintenance purposes by pushing green “ON” and red
“OFF” buttons simultaneously
3. To disconnect battery, mains and output, open battery MCCB/fuse and set input switch (Q001)
and output switch (Q002) to position “0”
With Q002 in position “0”, UPS will be operational and may be tested as a single system
without affecting other parallel UPS(s).
990-4050
66
Installation Guide APC Silcon 10-40kW 400V UPS
Options/Accessories
H002a
6.2.5 Switching Back to Normal Parallel/Redundant Operation
1. Turn input switch (Q001) and output switch (Q002) to position “1”
2. Charge capacitor, connect battery and start up UPS
UPS will automatically switch to normal operation and start load-sharing with other
parallelled UPS(s).
WARNING!
System will discharge built-in capacitors, but check terminal voltage before proceding.
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
67
Options/Accessories
6.3
Intersystem Synchronization Unit
Intersystem Synchronization Unit System (ISU System)
The ISU system consists of inter-connected ISUs. One ISU system may consist of up to 5 ISUs,
regardles of ISU configuration. The ISU system synchronizes the voltage of parallel operation
systems running in battery operation.
The ISU system may also include one or more external synchronization sources,
e.g. a gen-set or a non-APC Silcon UPS system.
Synchronization accuracy of the ISU is better than 2o.
Schematic overview of ISU system (example):
UPS 1A
UPS 1B
UPS 2B
Parallel
Operation
System 1
Parallel
Operation
System 2
UPS 1C
UPS 2A
ISU
1
UPS 2C
ISU
2
ISU System
ISU
4
UPS 4
ISU
3
ISU
5
Ext.
sync
Source
Parallel
Operation
System 3
UPS 3A
UPS 3C
UPS 3B
Intersystem Synchronization Unit (ISU)
The ISU is an active part of an ISU system, serving as the interface to the sources and the ISU
system.
The ISU can be connected to a parallel UPS configuration, using the standard parallel
communication controller in the parallel operation system.
(See Intersystem Synchronization Unit User’s Manual for further details.)
990-4050
68
Installation Guide APC Silcon 10-40kW 400V UPS
Options/Accessories
6.4
Relay Board
Relays
All relays are “fail safe”: In alarm modes, relay coil will be de-energized.
1
2
3
Maximum load: 8.0A – 250VAC
0.3A – 60VDC
Minimum load: 0.05A – 6VAC
0.05A – 6VDC
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
69
Options/Accessories
6.4.1 Relay Board/Relay Functions
NOTICE!
If alarm mode “Communication to controller lost” is active, ALL relays will indicate failure.
Relay Number
Message
Alarm-trigging Events
1 ##
(X002)
Mains outside limits
Mains voltage RMS outside limits
Mains wave form (fast detector) outside limits
Mains frequency outside limits
2 ##
(X003)
Bypass outside limits
Bypass voltage RMS outside limits
Bypass wave form (fast detector) outside limits
Bypass frequency outside limits
3 ##
(X004)
Output outside limits
Output voltage RMS value outside limits
Output wave form (fast detector) outside limits
Output frequency outside limits
4
(X005)
System overload
Output load exceeding 100%
Delta inverter current limiter active
Main inverter current limiter active
5
(X006)
Fan fault
Blocked or faulty fan
6
(X007)
Equipment
high temperature
Static switch temperature too high
Main inverter temperature too high
Delta inverter temperature too high
Magnetics temperature too high
Isolation transformer (option) temperature too high
Battery temperature too high
7
(X008)
MCCB battery off
Battery MCCB/Fuse not closed or released
8
(X009)
Normal operation
UPS running in normal operation mode (status)
9 ##
(X010)
Battery operation
UPS running in battery operation mode (status)
10 ## (X011)
Bypass operation
UPS running in bypass operation mode (status)
11 ## (X012)
Stand-by operation
UPS in stand-by mode
(Hot stand-by - parallel systems only)
Service bypass
operation
Service bypass switch active
Boost charge
operation
UPS boost-charging on battery
12
(X013)
13 ## (X014)
14
(X015)
Battery voltage
outside limits
DC voltage too high (shut down)
DC voltage below warning level
DC voltage too low (shut down)
15
(X016)
Battery condition
fault
ABM has detected weak battery condition
ABM has detected defect battery
(ABM = Advanced Battery Monitor)
Common fault
All alarms as mentioned above
(except relays 8+9+10+11)
Internal power supply fault
System locked in operation mode
Internal memory fault
Internal communication fault
16 ## (X017)
990-4050
70
Installation Guide APC Silcon 10-40kW 400V UPS
Options/Accessories
## Delay programmable in configuration stack: “Common fault delay”. Settings 0,10,20,30
seconds.
See section 5.2 in this guide for System configuration
NOTICE!
Alarm Trigging Events 1-23-9-10-11-13 activates the corresponding alarm relay after the delay.
Alarm Trigging Events 4-5-6-7-8-12-14-15 activates the corresponding alarm relay momentarily.
Common fault relay 16 is activated at the same time as relay 1-2-3-4-5-6-7-12-13-14-15, or in
any of the below situations:
• Internal power supply fault
• System locked in operation mode
• Internal memory fault
• Internal communication fault
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
71
Options/Accessories
6.5
Weight Equalizer
Footprint - 600mm and 8
19
75
277.5
755
277.5
R6
75
Rear
30 490 - 600mm cabinet
30 690 - 800mm cabinet
550 - 600mm cabinet
750 - 600mm cabinet
30
30
Front
990-4050
72
Installation Guide APC Silcon 10-40kW 400V UPS
Options/Accessories
Footprint - 1000mm Cabinet
75
277.5
755
277.5
R6
75
Rear
30
465 - 1000 mm cabinet
30
395 - 1000 mm cabinet
30
950 - 1000 mm cabinet
Front
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
73
Options/Accessories
6.6
Remote Display
With the remote display unit data may be displayed at distances of up to 25 m from UPS. For
extended communication distance, see section below.
Remote display may easily be connected to UPS via one of the two serial communication ports
on the communication interface board.
To obtain a transmission distance of up to 3.2 km normal RS232C signal levels must be
converted to a long distance communication standard. The converter must be placed outside
the UPS cabinet.
6.6.1 Extension of Remote Display Communication Distance
Remote display communicates with the UPS through a 3-wire RS232 interface. Remote display
is a DTE (Data Terminal Equipment) employing a SUB-D 9-pin female connector.
Communication speed: 9600 bps.
For communication distances, see Table 1. Insert converters if longer distances are necessary,
or if communication cables are led through magnetically noisy areas. Converters must comply
with local regulations
Table 1: Remote Display Communication Extensions
Standard
(RS232)
Short-haul
Modem Async
Max. distance
80/25 ft/m
10000/3200 ft/m
Converter Manufacture
Art. Code
No converter
BLACK BOX
ME800A-R2
RS232 BLACK BOX connector
Sub-D 25-pin female
BLACK BOX interconnector
4-screw terminal
Two converter boxes are required for a communication distance extension: One
box near the UPS for the conversion from RS232C to a long distance communication standard,
and another box at the other end to convert back to RS232C, which is to be connected to the
Remote Display. The converter provides optical signal insulation. Both converter boxes must
be supplied by an uninterruptible power source.
990-4050
74
Installation Guide APC Silcon 10-40kW 400V UPS
Options/Accessories
6.6.1.1Connections Without Converter
Connect a 25-pin female Sub-D and a 9-pin male Sub-D connector with a 3-wire shielded cable,
as shown in the table below. Connect shield at one end only.
Pin Connection for Interconnection Cable (without converter):
Host (DTE)
Remote Display (DTE)
25-pin female
pin No.
9-pin male
pin No.
2 (TXD)
2 (RXD)
3 (RXD)
3 (TXD)
7 (GND)
5 (GND)
House (shield)
No Connection
6.6.1.2Connections With Converter
Connections to be made according to converter manual.
Pinconnection example only:
Pin Connections for cable
from host to ME800A-R2.
Pin connection for cable from
ME800A-R2 to Remote Display
Host
(DTE)
ME800A-R2
(DCE)
ME800A-R2
(DCE)
Remote Display
(DTE)
25-pin female
pin No.
25-pin male
pin No.
25-pin male
pin No.
9-pin male
pin No.
2 (TXD)
3
3
2 (RXD)
3 (RXD)
2
2
3 (TXD)
7 (GND)
7
7
5 (GND)
House (Shield)
No connection
No connection
House (Shield)
The ME800A-R2 must be set up as a DCE with no RTS/DTR control.
The interconnection cable between the two ME800A-R2 boxes is a 4-wire twisted pair
telephone cable with or without shield. The shield improves noise immunity but reduces
maximum communication distance.
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
75
Options/Accessories
6.6.2 Remote Display Installation
6.6.2.1Connecting RS232C and Mains Adapter
CAUTION!
Wiring for alarm and signal circuit field to be rated 300V (minimum).
Rear view
Rear view
Front view
1. Turn 180° to loosen
the 4 screws
2. Remove front cover
3. Mont back plate
4. Connect cables
Cable entry from bottom and rear
DP9-F
Mains adapter
6.6.2.2Remote Display Power Supply
The remote display is supplied by normal AC power with no battery back-up. For UPS data
transmission to remote display to remain unaffected during power failure, the remote display
must be supplied from an uninterruptible power source.
Converters used to extend communication distance must also be supplied from uninterruptible
power sources.
6.6.2.3 Remote Display Cables
RS232C to RS232C cable:
APC Silcon, DB25-F
Remote Display, DB9-M
X
Connect shield at one end only!
Rating: Refer to Local/National electrical codes.
Communication voltage +15VDC
990-4050
76
Installation Guide APC Silcon 10-40kW 400V UPS
Options/Accessories
6.6.3
Remote Display Use
The remote display is an inactive unit unable to influence the operation of the UPS: Some of
the alarms visible on the internal display are also available on the remote display (See the
Alarm section in the APC Silcon User Guide).
6.6.3.1Initiating the Remote Display
After having connected the supply the display will show:
Remote Display: “APC Silcon UPS”
6.6.3.2Communication Fault
Communication fault between UPS and remote display will appear in the display as follows:
“Data transmission interrupted”
6.6.3.3 Remote Display Setting
Use # Stack to select language and type of UPS connected to remote display.
Parameter
Setting
Comments
Language
GB,D,F,DK, S, SF,NL, PL, CZ,
E, P, SK, H, I
Language
Host
SDC charger, DP300E, 300E
Type of UPS connected to remote
display
6.6.3.4Operation
See the Operation section in the APC Silcon User Guide.
6.6.3.5Display of Measured Value
See Display of Measured Value in the APC Silcon User Guide.
Time reading not visible from the remote display.
6.6.3.6Alarms
See Alarms section in the APC Silcon User Guide.
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
77
Options/Accessories
6.7
Isolation Transformer
1400mm
600 mm wide
APC Isolation
Transformer module
10-80kW
UPS
Height [mm]
Width [mm]
Depth [mm]
Weight [kg]
10 kW
20 kW
40 kW
1400
1400
1400
600
600
600
800
800
800
185
245
405
Example of Transformer Configuration (Yyno)
PE
PE
NOTICE!
APC isolation transformers are available in various configuration. Contact your local APC
representative for further information. See “How to Contact APC” in this guide.
990-4050
78
Installation Guide APC Silcon 10-40kW 400V UPS
Options/Accessories
6.7.1 Connecting Isolation Transformer
NOTICE!
If an MCCB is used in stead of external input fuses, the MCCB load capacity must be 8xIn
(nominal current) for minimum 10 ms.
Isolation
Transformer
External
Input Fuses*
FM [A]
380-415V
External
Input Cable
[mm2]
380-415V
External PE
Cable [mm2]
External
Output
Cable
[mm2]
External
Temp.
Signal
Cable max.
[mm2]
10kW
20
4
4
4
2
20kW
40
10
10
10
2
40kW
80
25
16
25
2
*DIN gL types
PVC cables isolated to withstand a maximum ambient temperature of 30oC.
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
79
Options/Accessories
NOTICE!
Check correct phase rotation of mains input voltage! Maximum input/output cables: 35mm2. If input neutral is not available, an optional Dzn0 or Dyn11 input isolation transformer must be used.
NOTICE!
All external cable dimensions are recommended sizes only. Refer to local legal regulations.
NOTICE!
Make sure that gland plate is installed in bottom of cabinet.
CAUTION!
At 100% switch mode load, neutral must be rated for 200% phase current.
990-4050
80
Installation Guide APC Silcon 10-40kW 400V UPS
Options/Accessories
6.7.2 Wiring up UPS with External Yyn0 Isolation Transformer at Output
WARNING!
Isolation transformer provides galvanic isolation between mains supply and load. Load will loose
galvanic isolation if isolation transformer is bypassed
NOTICE!
Refer to local legal regulation for wiring information.
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
81
Options/Accessories
6.7.3 Wiring up UPS with External Yyn0 Isolation Transformer at Input
WARNING!
Isolation transformer provides galvanic isolation between mains supply and load. Load will loose
galvanic isolation if isolation transformer is bypassed.
NOTICE!
Refer to local legal regulation for wiring information.
990-4050
82
Installation Guide APC Silcon 10-40kW 400V UPS
Options/Accessories
6.7.4 Wiring up UPS with External Optional Dzn0 Isolation Transformer at Input
WARNING!
Isolation transformer provides galvanic isolation between mains supply and load. Load will loose
galvanic isolation if isolation transformer is bypassed.
NOTICE!
Refer to local legal regulation for wiring information.
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
83
Options/Accessories
6.7.5 Wiring up UPS with External Optional Dzn0 Isolation Transformer at Output
WARNING!
Isolation transformer provides galvanic isolation between mains supply and load. Do not bypass
isolation transformer in order to avoid damaging circulation currents and to prevent load from
loosing galvanic isolation.
NOTICE!
Refer to local legal regulation for wiring information.
990-4050
84
Installation Guide APC Silcon 10-40kW 400V UPS
Options/Accessories
6.7.6 Wiring up UPS with External Optional Dyn11 Isolation Transformer at Input
WARNING!
Isolation transformer provides galvanic isolation between mains supply and load. Do not bypass
isolation transformer in order to avoid damaging circulation currents and to prevent load from
loosing galvanic isolation.
NOTICE!
Refer to local legal regulation for wiring information.
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
85
System Specifications
7.0 System Specifications
7.1
Technical Data
Voltage
Input
Output
3x380/400/415V
Voltage tolerance
Normal operation
Bypass operation
+15%
+10% (standard)
+4, 6, 8% (programmable)
Frequency
50Hz/60Hz
+6 standard
+0.5-8% (programmable)
Input power factor
load 25% minimum 0.97
load 100% minimum 0.99
Current distortion
Max. 5%
Voltage
3x380/400/415V
Voltage tolerance
+1% static symmetrical load
+3% static symmetrical load
+5% 0-100% load step
Voltage distortion
max. 3% linear load
max. 5% non-linear load
Load power factor
0.9 lead to 0.8 lag
Frequency
50Hz/60Hz (mains synchronized)
+0.1% free-running
Overload capacity
Mains operation
Mains operation
Battery operation
Bypass operation
General
200% - 60 seconds
125% - 10 minutes
150% - 30 seconds
125% - continuous
Ambient temperature
0-40oC (Temperatures above 25oC will
reduce battery lifetime)
Humidity
Protection class
Safety
Max. 95% non-condensing
IP30
EN 50091-1
CE Mark
EN 50091-2
Built-in
Programmable
Programmable
Emission and Immunity
Static bypass switch
Auto restart
Economy mode
7.2
Back-up Time / Dimensions / Weigh
Type
10kW
20kW
40kW
Back-up time.
UPS with builtin batteries
22 min.
50 min.
78 min.
8
min.
22
min.
35
min.
0
min.
8
min.
Height [mm]
1400
1400
1400
1400
1400
1400
1400
1400
Width [mm]
600
800
1000
600
800
1000
600
1000
Depth [mm]
800
800
800
800
800
800
800
800
Weight [kg]
385
550
755
400
585
765
285
650
990-4050
86
Installation Guide APC Silcon 10-40kW 400V UPS
Warranty
8.0 Warranty
8.1
APC Silcon Series Limited Factory Warranty
APC warrants that the unit, when properly installed and commissioned by APC or APC authorized
service personnel, shall be free from defects in materials and workmanship for a period of (1) year
from the date of installation or maximum 18 months after manufacturing. In the event that the unit
fails to meet the foregoing warranty, APC shall for a period of one (1) year repair or replace any
defective parts, without charge for on-site labor and travel if trained & authorized APC personnel
has conducted start-up of the unit.
An APC Start-Up Service must be performed/completed by APC or APC authorized service
personnel or the on-site factory warranty will be voided and replacement of defective parts only will
be covered. APC shall have no liability and no obligation to repair the installed unit if non-authorized
APC personnel performed the start-up and such start-up caused the unit to be defective.
APC SHALL NOT BE LIABLE UNDER THE WARRANTY IF ITS TESTING AND EXAMINATION
DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS
CAUSED BY PURCHASER’S OR ANY THIRD PERSON’S MISUSE, NEGLIGENCE, IMPROPER
INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR OR MODIFY, OR ANY
OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE,
LIGHTNING OR OTHER HAZARD.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, BY OPERATION OF LAW OR
OTHERWISE, OF PRODUCTS SOLD, SERVICED OR FURNISHED UNDER THIS AGREEMENT
OR IN CONNECTION HEREWITH. APC DISCLAIMS ALL IMPLIED WARRANTIES OF
MERCHANTABILITY, SATISFACTION AND FITNESS FOR A PARTICULAR PURPOSE. APC’S
EXPRESS WARRANTIES WILL NOT BE ENLARGED, DIMINISHED, OR AFFECTED BY AND NO
OBLIGATION OR LIABILITY WILL ARISE OUT OF, APC’S RENDERING OF TECHNICAL OR
OTHER ADVICE OR SERVICE IN CONNECTION WITH THE PRODUCTS. THE FOREGOING
WARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES
AND REMEDIES. THE WARRANTIES SET FORTH ABOVE, CONSTITUTE APC’S SOLE
LIABILITY AND PURCHASER’S EXCLUSIVE REMEDY FOR ANY BREACH OF SUCH
WARRANTIES. APC’S WARRANTIES RUN ONLY TO PURCHASER AND ARE NOT EXTENDED
TO ANY THIRD PARTIES.
IN NO EVENT SHALL APC, ITS OFFICERS, DIRECTORS, AFFILIATES OR EMPLOYEES BE
LIABLE FOR ANY FORM OF INDIRECT, SPECIAL, CONSEQUENTIAL OR PUNITIVE
DAMAGES, ARISING OUT OF THE USE, SERVICE OR INSTALLATION, OF THE PRODUCTS,
WHETHER SUCH DAMAGES ARISE IN CONTRACT OR TORT, IRRESPECTIVE OF FAULT,
NEGLIGENCE OR STRICT LIABILITY OR WHETHER APC HAS BEEN ADVISED IN ADVANCE
OF THE POSSIBILITY OF SUCH DAMAGES.
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
87
Appendix
9.0 Appendix
9.1
Table 1. Installation Planning Data
Q3
Service Bypass Panel
Main Input
Breaker *
Q1
Output
Breaker *
Q2
UPS Module
Field
Wiring*
Field
Wiring *
Battery Bank**
* Not supplied by APC
** Internal Batteries available for 40kW units and smaller
Installation Planning Data
APC Silcon Series
AC Input
Power rating
Source
Cable
Overcurrent
Full
Vn
load
INom
AC Output
IMax
Disch Disch
Load side
In
Heat
Overcurrent Dissipation
Pf
Nom.
Max.
Nom.
Max. (per phase) Protection*
(Vdc)
P(kW)
(A)
(A)
(A)
Protection*
(kW)
10
10
1
380 50/60
400
415
11.2
13.0
17.7
17.0
16.3
19.5
18.7
17.9
4mm2
20 A
2x384
10.8
14
16
15.2
14.5
13.9
16 A
0.54
20
20
1
380 50/60
400
415
22.2
25.7
35.3
33.7
32.4
38.8
37.1
35.6
10mm2
40 A
2x384
21.5
28
33
30.3
29.0
27.8
32 A
0.94
40
40
1
380 50/60
400
415
43.9
50.9
69.8
66.7
64.0
76.8
73.4
70.4
16mm2
80 A
2x384
42.2
55
65
60.6
58.0
55.6
63 A
1.5
1c
1d
1e
1f
1g
1h
2a
2b
2c
2d
3a
3b
4a
3
4
1
2
9
5, 6, 13
8
12
10
11
6, 7
13
1a
NOTES
Hz
I (A)
Input
kW kVA
COLUMN
V
P (kW)
Battery System DC
Min. Input
1b
* Provided by others
990-4050
88
Installation Guide APC Silcon 10-40kW 400V UPS
Appendix
Notes:
1. Nominal input current based on rated load.
2. Maximum input current based on rated load + full battery recharge. Full battery recharge
assumed to increase input current with 10%.
3.
Nominal power consumption (column 1c) based on nominal input current (1e) and the
corresponding input voltage (1a).
4. Maximum power consumption (1d) based on maximum input current (1f) and the corresponding
input voltage (1a).
5. Suggested input overcurrent protection (1h) based on continous full load maximum input current
(1f). MCCB breaker selection based on continous full load nominal input current (1e) is
acceptable, provided battery recharge time is short.
6. Fuses according to DIN LV HRC type gL, 500V assumed. MCCB load capacity must be 8xIn
(nominal current) for minimum 10ms.
7. Suggested load side overcurrent protection (3b) based on nominal output current (3a).
8. Nominal battery voltage assumed to be 2V/cell (Lead technologi).
9. Recommended cable sizes, see "External Connection" section of this guide.
CAUTION! Cable sizes must comply with national and/or local legal regulations.
10. Nominal battery discharge current (2c) based on full rated load and nominal battery
voltage (2V/cell).
11. Maximum battery discharge current (2d) based on full rated load and battery voltage at end of
discharge (1.7V/cell).
12. Full load discharge power from battery based on nominal battery discharge current
(2c) x nominal battery voltage (2x192cells x 2V/cell), or maximum battery discharge current
(2d) x battery voltage at end of discharge (2x192cells x 1.7 V/cell).
13. Heat dissipation based on nominal full load capacity and linear load.
990-4050
Installation Guide APC Silcon 10-40kW 400V UPS
89
How to Contact APC
10.0 How to Contact APC
APC Corporate
132 Fairgrounds Road
West Kingston, RI 02892
USA
Telephone: 401 789-5735
Fax:
401 789-3710
PowerFax™: 800 347-FAXX
Pre-sales Technical Support
877-474-5266 (1-877-4Silcon)
Post-sales Technical Support
877-287-7835 (1-877-2UPS-TEK)
Web: www.apcc.com/support/contact/contact_support.cfm
APC Denmark
Silcon Allé
DK-6000 Kolding
Denmark
Telephone: + 45 75 54 22 55
Fax:
+ 45 72 19 03 50
Pre-sales Technical Support
+ 45 72 19 04 99
Post-sales Technical Support
+ 353 91 70 2000
Web: www.apcc.com/support/contact/contact_support.cfm
990-4050
90
Installation Guide APC Silcon 10-40kW 400V UPS
Download PDF

advertising