APC CTEP0-120 Network Router User Manual

BroadBand CTEP/G Series
Zero, Three, Six Battery Pole/Ground Mount Enclosures
120 V/240 V
User’s Manual
990-5520A 08/02
Chapter 1 General Information
The CTEP/G Series Enclosures provide housing for a power source for broadband cable operations.
Safety
This Safety Guide contains important instructions that should be followed during installation and
maintenance of the APC equipment and batteries. It is intended for APC customers who setup,
install, relocate, or maintain APC equipment. Changes and modifications to this unit not expressly
approved by APC could void the warranty.
Failure to observe these warnings may result in serious injury, death or damage to the
equipment.
Electrical
Warnings
Do not work alone under hazardous conditions.
Do not handle any metallic connector before the power has been disconnected.
Servicing this equipment may require working with protective covers removed
and utility power connected. Use extreme caution during these procedures.
High current through conductive materials could cause severe burns.
When grounding cannot be verified, disconnect the equipment from the utility
power outlet before installing or connecting to other equipment. Reconnect the
power cord only after all connections are made.
Check that the power cord(s), plug(s), and sockets are in good condition.
Replacement of fuses or other parts must be with identical types and ratings.
Substitution of nonidentical parts may cause safety and fire hazards.
Battery
Warnings
Danger of explosion if battery is incorrectly connected or replaced. Replace
batteries only with same or equivalent type recommended by the
manufacturer.
Batteries must be recycled. Deliver the battery to an appropriate recycling
facility or ship it to the supplier in the new battery packing material.
Overhead
Warnings
Never stand underneath anything while it is hoisted. Always wear a hard hat.
Lifting
Warnings
Modules are heavy. Use proper lifting techniques and equipment to avoid
injury.
1
Chapter 2 Installation
Only trained service personnel should install and maintain the power supply enclosure.
Prior to installing the power supply enclosure, a utility breaker box must be installed on the pole.
Utility line voltage must be routed to the enclosure. Local, state, federal and/or National Electric
Code (NEC) regulations regarding location, permits and electrical wiring must be adhered to.
Do not operate the power supply where the temperature and humidity are outside the specified limits.
See Specifications in this manual.
Specifications
Models Supported
Model Number
Description
CTEP0-120
Encl, Pole 0 Batt 20 A, 120 VAC, 60 Hz
CTEP3-120
Encl, Pole 3 Batt 20 A, 120 VAC, 60 Hz
CTEP3-240
Encl, Pole 3 Batt 20 A, 240 VAC, 60 Hz
CTEP6-120
Encl, Pole 6 Batt 20 A, 120 VAC, 60 Hz
CTEP6-120GI
Encl, Pole 6 Batt w/ Generator Interface, 20 A, 120 VAC, 60 Hz
CTEG0-120
Encl, Ground 0 Batt 20 A, 120 VAC, 60 Hz
CTEG3-120
Encl, Ground 3 Batt 20 A, 120 VAC, 60 Hz
CTEG6-120
Encl, Ground 6 Batt 20 A, 120 VAC, 60 Hz
CTEG6-120GI
Encl, Ground 6 Batt w/ Generator Interface, 20 A, 120 VAC, 60 Hz
Environmental Specifications
Operating Temperature
-40º F to140º F (-40º C to 60º C)
Humidity
5% to 95% noncondensing within enclosure
Physical Specifications
Characteristic
Specification
Height X Width X Depth
CTEP0
CTEP3
CTEP6
14” x 24” x 16” (36 x 61 x 41 cm)
30” x 24” x 16” (76 x 61 x 41 cm)
39” x 24” x 16” (99 x 61 x 41 cm)
Height X Width X Depth
CTEG0
CTEG3
CTEG6
22” x 24” x 16” (56 x 61 x 41 cm)
38” x 24” x 16” (97 x 61 x 41 cm)
47” x 24” x 16” (119 x 61 x 41 cm)
Weight
CTEP/G0
CTEP/G3
CTEP/G6
23 lbs (10 kg)
50 lbs (23 kg)
77 lbs (35 kg)
2
Unpacking
Inspect the unit upon receipt. Notify the carrier if there is damage.
The packaging is recyclable; save it for reuse or dispose of it properly.
Check the package contents. The package contains the enclosure, battery cables, connectors and
associated hardware and product documentation.
CTEP/G3: (5 cables); 15” black battery jumpers (2), 24” black (1),
27” red (2), 34” red (1).
CTEP/G6: (9 cables); 15” black battery jumpers (4), 25” black (1), 40” black (1),
60” black (1), 27” red (1), 34” red (1).
Installing the Enclosure
Pole Mount Installation
CTEP 0 Model
Top Hole
.75” (2 cm)
7” (18 cm)
Bottom Hole
.75” (2 cm)
Bottom Edge of Housing
5/8” Pole
Mounting Bracket
Bolt and
is permanently
Square
attached to
Washer
enclosure.
CTEP3 Model
Top Hole
.75” (2 cm)
Mounting Bracket
is permanently
attached to
enclosure.
12” (30 cm)
Bottom Hole
.75” (2 cm)
5/8” Pole
Bolt and
Square
Washer
Bottom Edge of Housing
3
CTEP6 Model
Top Hole
.75” (2 cm)
12” (30 cm)
Middle Hole
.75” (2 cm)
12” (30 cm)
Mounting Bracket
is permanently
attached to
enclosure.
Bottom Hole
.75” (2 cm)
5/8” Pole
Bolt and
Square
Washer
Bottom Edge of Housing
Ground Mount Installation
1.
Install an APC approved concrete pad. Contact your dealer or see How to Contact APC, in this
manual for more information.
2.
Secure the enclosure to the pad.
0 Battery Enclosure:
Attach the ground skirt to the concrete pad.
Attach the enclosure to the ground skirt.
3 Battery, 6 Battery Enclosures:
Place the enclosure on the pad. The holes on the
enclosure must be aligned with the anchor hooks
on the pad, (hardware not included).
This is a general representation of an enclosure
mounted on a pad. Configurations may vary.
Meter Base
Coax Housing
4
Service Entrance/
Load Center
Coax Housing
Wiring
Grounding
1. Install and interconnect ground rods appropriate for proper grounding according to local
electrical code requirements.
2.
Route ground wires from the ground system into the bus bar located on the enclosure.
Connecting Utility Power to the Enclosure
EP3
(EP6 has additional battery tray)
EP0
Tamper Switch
Present on all Models
Status Monitoring Lamp
Present on all Models
Site for Power Supply
Battery Tray
Grounding Wire
Output Connection to Coax
Electrical Input Output Box
Optional External AC
Generator Interface
Maintenance Bypass Switch
To CTSP Utility
Output Terminals
Auxiliary Power
Supply Connection
Output Voltage Sensor
1.
Unlock and open the door of the enclosure.
2.
Ensure that the utility power switch is OFF.
3.
Install a high magnetic circuit breaker box
4.
Using appropriate conduit connectors, run wires from the utility breaker box to the receptacle
box inside the enclosure.
5.
Connect the wires to the receptacle and install it in the enclosure.
6.
Refer to the CTSP-EM User’s Manual for detailed installation instructions regarding the
Interface Harness connections.
5
Options
The CTEP/G6-120GI has an optional External AC Generator Interface.
For available options see your dealer or the APC web site, www.apc.com/support.
Connecting the Batteries
The battery circuit breaker must OFF prior to battery installation.
Use normal precautionary measures when wiring and connecting the batteries.
Tape one end of each jumper cable prior to installation.
CTEP3
Bottom Shelf
27” Red
to Circuit Breaker
25” Black to CTSP
34” Red to CTSP
Circuit Breaker
Top Shelf
CTSP Battery
Connection
Cables from
Battery and
Circuit Breaker
6
CTEP6
Bottom Shelf
60” Black
to Battery 3+
40” Black
to Battery 1Middle Shelf
27” Red to Circuit Breaker
60” Black
to Circuit Beaker
25” Black
to CTSP
34” Red
to CTSP
Circuit Breaker
40” Black
from Battery 6Top Shelf
CTSP Battery
Connection
Cables from
Battery 3- and
Circuit Breaker
7
Chapter 3 Service, Contact and Warranty Information
Service
APC makes every effort to ensure parts and equipment arrive in working condition. Occasionally, it
may be necessary to return parts or equipment that are not in working condition.
If the UPS requires service do not return it to the dealer. Instead, follow these steps:
1.
2.
Contact APC Customer Service through the APC web site, www.apc.com/support.
Note the product model number, the serial number, and the date purchased. If you call APC
Customer Service, a technician will ask you to describe the problem and try to solve it over
the phone. If this is not possible the technician will issue a Returned Material Authorization
Number (RMA#).
If the product is under warranty, repairs are free. If not, there is a repair charge.
Procedures for servicing or returning products may vary internationally. Refer to the APC
web site. Select the appropriate country from the country selection field. Select Support
from the tab at the top of the web page.
Pack the product in its original packaging. If the original packing is not available, refer to the
APC web site for information on obtaining appropriate packing materials.
Pack the unit properly to avoid damage in transit. Never use Styrofoam beads for packaging.
Damage sustained in transit is not covered under warranty.
3.
Mark the RMA# on the outside of the package.
4.
Return the unit by insured, prepaid carrier to the address given to you by Customer Service.
How to Contact APC
In the USA …
Outside the USA …
Refer to the APC web site, Refer to the APC web site, www.apc.com. Select the appropriate
www.apc.com/support.
country from the country selection field. Select the Support tab at
the top of the web page.
8
Limited Warranty
American Power Conversion (APC) warrants its products to be free from defects in materials and workmanship for a period of
two years from the date of purchase. Its obligation under this warranty is limited to repairing or replacing, at its own sole
option, any such defective products. To obtain service under warranty you must obtain a Returned Material Authorization
(RMA) number from customer support. Products must be returned with transportation charges prepaid and must be
accompanied by a brief description of the problem encountered and proof of date and place of purchase. This warranty does
not apply to equipment that has been damaged by accident, negligence, or misapplication or has been altered or modified in
any way. This warranty applies only to the original purchaser who must have properly registered the product within 10 days of
purchase.
EXCEPT AS PROVIDED HEREIN, AMERICAN POWER CONVERSION MAKES NO WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s)
may not apply to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL APC BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, APC is not liable for any costs, such as lost profits or
revenue, loss of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties,
or otherwise.
Regulatory Approval
Entire contents copyright © 2002 by American Power Conversion Corporation. All rights reserved. Reproduction in whole or
in part without permission is prohibited.
APC is a registered trademark of American Power Conversion Corporation. All other trademarks are the property of their
respective owners.
9