BroadBand
CTSLLP/G Series
Pole and Ground Mount Standby Power Supply Enclosures
User Manual
990-5517 04/2003
Chapter 1 General Information
The CTSLLP/G Standby Power Supply Series Enclosures provide a power source for broadband
cable operations.
Safety
This Safety Guide contains important instructions that should be followed during installation and
maintenance of the APC equipment and batteries. It is intended for APC customers who setup,
install, relocate, or maintain APC equipment.
Changes and modifications to this unit not expressly approved by APC could void the
warranty.
Failure to observe these warnings may result in serious injury, death or damage to the
equipment.
•
Do not work alone under hazardous conditions.
•
Do not handle any metallic connector before the power has been
disconnected.
•
Servicing this equipment may require working with protective covers
removed and utility power connected. Use extreme caution during these
procedures.
•
High current through conductive materials could cause severe burns.
•
When grounding cannot be verified, disconnect the equipment from the
utility power outlet before installing or connecting to other equipment.
Reconnect the power cord only after all connections are made.
•
Check that the power cord(s), plug(s), and sockets are in good condition.
•
Replacement of fuses or other parts must be with identical types and
ratings. Substitution of nonidentical parts may cause safety and fire
hazards.
Lifting
Warnings
•
These units are heavy. Use proper lifting techniques and equipment to
avoid injury.
Overhead
Warnings
•
Never stand underneath anything while it is being hoisted.
•
Always wear a hardhat.
Electrical
Warnings
1
Specifications
Environmental Specifications
Operating Temperature
-40º F to 140º F (-40º C to 60º C)
Humidity
5% to 95% noncondensing within enclosure
Physical Specifications
Characteristic
Height x Width x Depth
CTSLLGULH110S1
CTSLLPULH100S1
CTSLLGECH220S1
Weight
CTSLLGULH110S1
CTSLLPULH100S1
CTSLLGECH220S1
Specification
20” x 22” x 7.5” (51cm x 56 cm x 19 cm)
14” x 22” x 7.5” (36 cm x 56 cm x 19 cm)
20” x 22” x 7.5” (51cm x 56 cm x 19 cm)
20 lbs (9 kg)
16 lbs (7 kg)
20 lbs (9 kg)
Electrical Specifications
Input Characteristic
Input Voltage
CTSLLGULH110S1
CTSLLPULH100S1
CTSLLGECH220S1
Input Specification
120 Vac
120 Vac
220 Vac
2
Chapter 2 Installation
Only trained service personnel should install and maintain the power supply.
Prior to installation, utility line voltage must be routed to the enclosure. Local, state, federal and/or
National Electric Code (NEC) regulations regarding location, permits and electrical wiring must be
adhered to.
Do not operate the power supply where the temperature and humidity are outside the specified limits.
See Specifications in this manual.
Unpacking
Inspect the unit upon receipt. Notify the carrier if there is damage.
The packaging is recyclable; save it for reuse or dispose of it properly.
The package contains:
the enclosure
a temperature sensor
SLLP models; wiring harness
product documentation
Models Supported
Model Number
Description
CTSLLGULH110S1
Enclosure, SLL-G, 120 Vac, SM Ready, UL
CTSLLPULH100S1
Enclosure, SLL-P, 120 Vac, SM Ready, UL
CTSLLGECH220S1
Enclosure, SLL-GEC, 230 Vac, SM Ready. CE
3
CTSLL Enclosure Installation
CTSLLG Enclosure Installation
1.
Remove the lid from the battery vault.
2.
Position the CTSLLG on the edge of the vault lid.
3.
Install two 5/16” (.8 cm) x 1” (2.5 cm) flat head screws through the lid into the holes in the back
of the CTSLLG.
4.
Install four 5/16” (.8 cm) x 3/4” (2 cm) flat head screws through the lid into the holes in the front
and sides of the CTSLLG.
5.
Replace the lid with the attached enclosure, onto the vault. See diagram.
6.
Upend the vault to a 90º angle, taking care that the enclosure does not fall.
7.
Insert two 3” (8 cm) carriage bolts into one of the long brackets.
8.
Place the bracket on the underside mounting lip on the vault lid.
9.
Insert the other long bracket onto the carriage bolts and partially tighten using two flat washers
and nuts.
10. Slide the bracket upward toward the front edge of the vault lid.
11. Use the same procedure to install the two short brackets at the rear of the vault lid.
12. Lower the vault with the enclosure attached into the prepared hole. Refer to the battery vault
User Manual, 990-1220.
4
CTSLLP Enclosure Installation
When wall mounting, use screws that are appropriate for the weight of the unit and the mounting
surface material. Refer to Specifications in this manual.
Top Hole
.75” (2 cm)
11.5” (29 cm)
Mounting Bracket
is permanently
attached to the
enclosure.
Bottom Hole
.75” (2 cm)
5
5/8” (1.5 cm)
Pole Bolt and
Square Washer
Controls and Indicators
CTSLLP/G Bottom View
Index
Control/Indicator
Definition
1
Ground wire lug
Provides connection of chassis to earth ground
2
Utility power input
indicator lamp (not
present on all models)
Yellow indicator illuminates when line voltage is present
3
Normal indicator lamp
Green indicator illuminates when the unit is operating in normal
mode, (output is provided by CTFLM module)
4
Standby indicator
lamp
Red indicator illuminates when the power supply has transferred
from normal to emergency or backup operation, (usually
indicates loss of line voltage)
5
Entry point for utility
power conduit – ½”
(1.3 cm)
Physical entry point for utility power input wiring
6
Optional second
CTFLM cable adapter
Coax adapter used when an optional backup CTFLM module is
installed
7
Status monitoring
connector
Entry point for status monitoring connector
8
Output cable adapter
Coax adapter for power supply output
6
Wiring
Install an approved 20 A high-magnetic utility circuit breaker.
Ensure the utility circuit breaker is OFF.
•
Unlock and open the front/top panel on the CTSLLP/G.
Refer to the diagram below for wiring details.
•
Connect the black and white wires from the incoming utility line.
•
Route the power feed coax to the bottom of the enclosure and attach to the coax cable
adapter using a pin connector.
•
Attach the stinger lug to the pin connector center pin.
•
Attach suitable solid copper ground wire to the enclosure ground lug and ground in
accordance with local codes.
•
Check for voltages between each connector pin and ground using a multimeter.
Presence of voltage indicates an improper ground. If voltage is present ensure the
ground contact is secure.
•
Reinstall the front/top panel on the CTSLLP/G.
7
Install the Battery Vault
Refer to User Manual 990-1220 packaged with the battery vault for installation instructions.
Connect the Batteries in the Battery Vault
Refer to User Manual 990-1220 packaged with the Battery Vault for battery connection details.
Install the temperature sensor on top of the batteries as shown in the 990-1220 User Manual.
Install the CTFLM and the CTSLM
Refer to the User Manual 990-5501 packaged with the CTFLM and CTSLM for installation
instructions.
Connect the CTFLM and CTSLM
Refer to the User Manual 990-5501 packaged with the CTFLM and CTSLM for connecting and
operating instructions.
8
Chapter 3 Troubleshooting and Maintenance
Troubleshooting Power Supply Failure
Problem
Power Supply
Failure
Possible Cause
No input voltage detected at connector J1, pins
1 and 2.
Solution
Replace the wiring harness
Input voltage present at connector J1, pins 1
and 2.
Disconnect power from the
supply
No input voltage at the black and white wires
input lines.
Replace the Euro block
Input voltage present at the black and white
wire input lines.
Replace the wiring harness.
No voltage at the Coax stinger.
Replace the CTFLM module
Maintenance
Routine Maintenance Schedule
Operation
Visual Inspection
External Surfaces
Connectors
Operator Controls
Wiring/Cable Assemblies
Interval
Semiannually
Annually
Annually
Annually
Cleaning
External Surfaces
External Controls/Receptacles
Internal Receptacles/Circuit Boards
Annually
Annually
Annually
Performance Verification
Refer to Initial Startup in the 990-5501
CTFLM/CTSLM User Manual
Semiannually
9
Routine Maintenance Procedures
•
Visual Inspection
•
•
Check external surfaces, connectors, indicators and wiring/cable assemblies for signs of
dirt, wear, and damage.
Cleaning
•
Brush dust from controls and receptacles using a small paintbrush.
•
Wipe surfaces with clean, dry cheesecloth.
•
Clean exterior surface with clean cheesecloth moistened with isopropyl alcohol or a
general purpose detergent.
NOTE: Do not allow cleaning solution into the interior of the enclosure or into any connectors.
•
Clean electrical contacts with approved spray-type contact cleaner.
Clean internal receptacles and circuit boards with hand controlled, dry-air jet (not more than 15
lb/in²), clean cheesecloth moistened with isopropyl alcohol. Wipe dry with clean, dry cheesecloth.
Replacement Procedures
•
Wiring Harness Replacement
•
Switch the utility circuit breaker OFF.
•
Remove/open the enclosure door(s).
•
Switch the CTFLM OFF.
•
Remove the CTFLM.
•
Disconnect the stinger lug from the pin connector, center pin.
•
Disconnect the utility wires and the ground wires.
•
Remove the two quick disconnect connectors from the top of the indicator lamp socket.
•
Remove the module connector plate by removing the Phillips head screws located on
the front and back of the enclosure.
•
Slide the module connector plate and harness to the left and out of the harness plate.
•
Slide the replacement connector plate and harness onto the harness plate and replace the
screws.
•
Reattach the ground wires.
•
Replace the quick disconnects on the indicator lamp socket.
•
Reconnect the utility wires and the stinger lug.
•
Reinstall the CTFLM. Ensure the module is seated properly.
•
Switch the CTFLM and the utility circuit breakers ON.
10
•
•
Complete Performance Verification. Refer to Initial Startup in the CTFLM/CTSLM
User Manual 990-5501.
•
Replace/close the enclosure door(s).
Indicator Lamp Replacement
Gently pry the lens off the indicator lamp using the tip of a screwdriver.
NOTE: Place a hand over the lens as it is loosened to ensure that the lens is not lost during the
procedure.
•
Remove the spent lamp and replace it with a new one.
•
Snap the lens back into place.
Euro Block Replacement
•
Switch the utility circuit breaker OFF.
•
Remove/open the enclosure door(s).
•
Remove the CTFLM.
•
Disconnect (and tag), the wiring harness and utility wires from the Euro block.
•
Remove the screws that secure the Euro block in the enclosure, and lift out the Euro block.
•
Insert the new Euro block and secure it in the enclosure.
•
Reconnect the wiring harness to the Euro block.
•
Reinstall the CTFLM.
•
Replace/close the enclosure door(s).
•
Switch the utility circuit breaker ON.
•
Complete Performance Verification. Refer to Initial Startup in the CTFLM/CTSLM User
Manual 990-5501.
11
Chapter 4 Service, Contact and Warranty Information
Service
APC makes every effort to ensure parts and equipment arrive in working condition. Occasionally, it
may be necessary to return parts or equipment that are not in working condition.
If the unit requires service do not return it to the dealer. Follow these steps:
1.
Contact APC Customer Service through the APC web site, www.apc.com/support.
Note the product model number, the serial number, and the date purchased. If you call APC
Customer Service, a technician will ask you to describe the problem and try to solve it over
the phone. If this is not possible the technician will issue a Returned Material Authorization
Number (RMA#).
If the product is under warranty, repairs are free. If not, there is a repair charge.
Procedures for servicing or returning products may vary internationally. Refer to the APC
web site. Select the appropriate country from the country selection field. Select Support
from the tab at the top of the web page.
2.
Pack the product in its original packaging.
Pack the unit properly to avoid damage in transit. Never use Styrofoam beads for packaging.
Damage sustained in transit is not covered under warranty.
3.
Mark the RMA# on the outside of the package.
4.
Return the unit by insured, prepaid carrier to the address given to you by Customer Service.
How to Contact APC
In the USA …
Outside the USA …
Refer to the APC web site,
www.apc.com/support.
Refer to the APC web site, www.apc.com. Select the appropriate
country from the country selection field. Select the Support tab at
the top of the web page.
12
Limited Warranty
American Power Conversion (APC) warrants its products to be free from defects in materials and workmanship for a period of
two years from the date of purchase. Its obligation under this warranty is limited to repairing or replacing, at its own sole
option, any such defective products. To obtain service under warranty you must obtain a Returned Material Authorization
(RMA) number from customer support. Products must be returned with transportation charges prepaid and must be
accompanied by a brief description of the problem encountered and proof of date and place of purchase. This warranty does
not apply to equipment that has been damaged by accident, negligence, or misapplication or has been altered or modified in
any way. This warranty applies only to the original purchaser who must have properly registered the product within 10 days of
purchase.
EXCEPT AS PROVIDED HEREIN, AMERICAN POWER CONVERSION MAKES NO WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s)
may not apply to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL APC BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, APC is not liable for any costs, such as lost profits or
revenue, loss of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties,
or otherwise.
Regulatory Approval
Entire contents copyright © 2003 by American Power Conversion Corporation. All rights reserved. Reproduction in whole or
in part without permission is prohibited.
APC is a registered trademark of American Power Conversion Corporation. All other trademarks are the property of their
respective owners.
13