APC NBWL0456 Baby Monitor User Manual

Installation and
Quick Configuration
Manual
NetBotz® Room
Monitor 455
NBWL0455
NBWL0456
This manual is available in English on the enclosed CD.
Dieses Handbuch ist in Deutsch auf der beiliegenden CD-ROM
verfügbar.
Este manual está disponible en español en el CD-ROM adjunto.
Ce manuel est disponible en français sur le CD-ROM ci-inclus.
Questo manuale è disponibile in italiano nel CD-ROM allegato.
本マニュアルの日本語版は同梱の CD-ROM からご覧になれます。
Instrukcja obsługi w języku polskim jest dostępna na CD.
O manual em Português está disponível no CD-ROM em anexo.
Данное руководство на русском языке имеется на
прилагаемом компакт-диске.
an ual finns tillgänglig på svensk a på med fö ljande CD.
您可以从包含的 CD 上获得本手册的中文版本。
동봉된 CD 안에 한국어 매뉴얼이 있습니다 .
Contents
Introduction 1
Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Document Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Additional Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
InfraStruXure-certified . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Physical Description 4
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Inventory 6
Installation 8
Install the NetBotz 455 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Electrical box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Ceiling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Connect the NetBotz 455 to Your Network . . . . . . . . . . . . . . . . 12
Power-over-Ethernet (PoE) injector . . . . . . . . . . . . . . . . 12
PoE-capable hub or switch . . . . . . . . . . . . . . . . . . . . . . 12
Connect Sensors to Sensor Ports . . . . . . . . . . . . . . . . . . . . . . . 13
Connect Sensors and Sensor Pods to A-Link Ports. . . . . . . . . 14
Adjust the Lens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Initial Configuration 16
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Obtain network settings using DHCP . . . . . . . . . . . . . . . 16
Configure network settings using the Serial
Configuration Utility . . . . . . . . . . . . . . . . . . 17
Install a wireless network device . . . . . . . . . . . . . . . . . . 19
NetBotz 455 Installation and Quick Configuration Manual
i
The APC Configuration Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Access an Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Administrator account user ID and password . . . . . . . . . 20
Root account user ID and password . . . . . . . . . . . . . . . 20
Lost password recovery . . . . . . . . . . . . . . . . . . . . . . . . . 21
Basic View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Advanced View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
APC Quick Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Configure appliance settings . . . . . . . . . . . . . . . . . . . . . 23
Configure alert actions . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Upgrade Options 25
Software Feature Upgrades. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Hardware Upgrades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Add pods to your appliance . . . . . . . . . . . . . . . . . . . . . . 26
Connect a USB modem . . . . . . . . . . . . . . . . . . . . . . . . . 28
Connect a USB digital I/O device . . . . . . . . . . . . . . . . . . 28
Connect an APC Switched Rack PDU . . . . . . . . . . . . . . 29
Connect external sensors . . . . . . . . . . . . . . . . . . . . . . . 30
Clean the NetBotz 455 30
Specifications 31
Warranty 32
Two-Year Factory Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Terms of warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Non-transferable warranty . . . . . . . . . . . . . . . . . . . . . . . 32
Exclusions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Warranty claims . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
ii
NetBotz 455 Installation and Quick Configuration Manual
Introduction
Product Description
The American Power Conversion (APC®) NetBotz® Room Monitor 455
functions as the central hardware appliance for a NetBotz security and
environmental monitoring system. The NetBotz 455 can be installed anywhere
in a room and includes an integrated camera and internal sensors that monitor
temperature, humidity, air flow, and motion. It also includes four sensor ports
for connecting temperature, humidity, smoke, door, vibration, spot fluid, and
third-party dry contact and 0–5 V sensors. Plus, it supports two-way audio,
audio sensing, and audio recording. You can increase the space monitored by
adding up to two NetBotz sensor pods.
The integrated camera includes the following features:
• Image processor that generates images up to 1280 x 1024 resolution,
24-bit color, and up to 30 frames per second.
Note: The maximum frame rate describes the maximum
number of images that the camera imager is capable of
producing each second. The actual frame rate is dependent on
the amount of available bandwidth and current resolution.
• Image Size: 7.7 mm x 6.1 mm (9.82 mm diagonal = 0.387 in).
• Field of View: 64º (H) x 53º (V) for all resolutions.
• User adjustable and switchable industry-standard CS-mount lens.
CS-mount permits access to hundreds of different general purpose and
special purpose lenses.
NetBotz 455 Installation and Quick Configuration Manual
1
Attention: THE EQUIPMENT CONTAINS, AND THE
SOFTWARE ENABLES, VISUAL RECORDING CAPABILITIES,
THE IMPROPER USE OF WHICH MAY SUBJECT YOU TO
CIVIL AND CRIMINAL PENALTIES. APPLICABLE LAWS
REGARDING THE USE OF SUCH CAPABILITIES VARY
BETWEEN JURISDICTIONS AND MAY REQUIRE AMONG
OTHER THINGS EXPRESS WRITTEN CONSENT FROM
RECORDED SUBJECTS. YOU ARE SOLELY RESPONSIBLE
FOR INSURING STRICT COMPLIANCE WITH SUCH LAWS
AND FOR STRICT ADHERENCE TO ANY/ALL RIGHTS OF
PRIVACY AND PERSONALTY. USE OF THIS SOFTWARE FOR
ILLEGAL SURVEILLANCE OR MONITORING SHALL BE
DEEMED UNAUTHORIZED USE IN VIOLATION OF THE END
USER SOFTWARE AGREEMENT AND RESULT IN THE
IMMEDIATE TERMINATION OF YOUR LICENSE RIGHTS
THEREUNDER.
Document Overview
The NetBotz Room Monitor 455 Installation and Quick Configuration Manual
describes how to install a NetBotz Room Monitor 455, how to connect devices
to the appliance, and how to configure network settings. After performing the
configuration procedures in this manual, you can access your system through its
software interface, perform additional configuration tasks, and begin
monitoring the environment.
Related Documents
Unless otherwise noted, the following documentation is available on the CD
provided with the appliance or on the applicable product page on the APC Web
site, www.apc.com. To quickly find a product page, enter the product name or
part number in the Search field.
NetBotz Appliance User’s Guide – Includes all details for using, managing, and
configuring a NetBotz system with one of the following appliances: NetBotz
Room Monitor 355 (NBWL0355, NBWL0356), NetBotz Rack Monitor 450
(NBRK0450), NetBotz Room Monitor 455 (NBWL0455, NBWL0456), or
NetBotz Rack Monitor 550 (NBRK0550).
2
NetBotz 455 Installation and Quick Configuration Manual
Additional Options
The following options are available for the NetBotz 455. For more information
about any of the options, contact your APC representative or the distributor
from whom you purchased your APC product.
• NetBotz Camera Pod 160 (NBPD0160)
• NetBotz Rack Sensor Pod 150 (NBPD0150)
• NetBotz Room Sensor Pod 155 (NBPD0155)
• Temperature Sensor (AP9335T)
• Temperature/Humidity Sensor (AP9335TH)
• Temperature Sensor with Digital Display (AP9520T)
• Temperature/Humidity Sensor with Digital Display (AP9520TH)
• NetBotz Spot Fluid Sensor (NBES0301)
• NetBotz Door Switch Sensor for Rooms or Third Party Racks
(NBES0302)
• NetBotz Door Switch Sensor for APC Racks (NBES0303)
• NetBotz Dry Contact Cable (NBES0304)
• NetBotz 0-5 V Sensor Cable (NBES0305)
• NetBotz Vibration Sensor (NBES0306)
• NetBotz Smoke Sensor (NBES0307)
• NetBotz USB-to-Serial Cable (NBAC0226)
• NetBotz Sensor Pod 120 (NBPD0122)
• NetBotz Camera Pod 120 (NBPD0121)
InfraStruXure-certified
This product is certified for use in APC InfraStruXure® systems.
NetBotz 455 Installation and Quick Configuration Manual
3
Physical Description
Front
Item
4
Description

Vented internal
sensors

Network link LED Shows the status of the network connection. Blinks to indicate network
traffic (green—connected at 10 Mbps; yellow—connected at 100 Mbps).

Power LED
Indicates whether the unit is receiving power (green—receiving power;
dark—not receiving power).

Camera LED
Blinks steadily when the integrated camera is active.

Alert LED
Indicates the alert status of the system. When more than one alert exists,
the most severe will be indicated.
• Flashing once every eight seconds—Informational
• Flashing once every four seconds—Warning
• Flashing once every two seconds—Error
• Flashing once every second—Critical
• Flashing twice per second—Failure

Temperature
display
• Displays the current temperature from 0 to 99 in Centigrade or
Fahrenheit. Temperature reading from internal temperature sensor. If
the temperature exceeds 99, the display will flash 99.
• When the unit first receives power, displays the unique identifier
number for one minute.
• If an alert exists, flashes at the same rate as the Alert LED.
• During a firmware upgrade, displays 88.

Lens housing
Must be removed to change the focus of the integrated camera.
Vented opening for airflow, temperature, and humidity sensors.
NetBotz 455 Installation and Quick Configuration Manual
Rear
Item
Description

Microphone jack
Supports audio sensing, audio recording, and two-way audio.
Maximum length of microphone cable: 3 m (9.8 ft).

Speaker jack
Supports two-way audio.
Maximum length of speaker cable: 3 m (9.8 ft).

A-Link port
Used for cascading NetBotz sensor pods and temperature and humidity
sensors with digital displays. Provides communications and power to the
connected devices over standard CAT-5 cabling with straight-through
wiring. For details, see “Connect Sensors and Sensor Pods to A-Link
Ports” on page 14.

10/100 Base-T
network port
Provides for a 10/100 Base-T network connection and power through
Power-over-Ethernet (PoE). Status and link LEDs indicate network
traffic:
• Status LED—blinks orange and green at start-up; indicates the status of
the network connection (solid green—IP address established; blinking
green—attempting to obtain an IP address).
• Link LED—blinks to indicate network traffic (green—connected at 10
Mbps; orange—connected at 100 Mbps).

Sensor ports (4)
Used for connecting APC sensors, third-party dry-contact sensors, and
standard third-party 0-5 V sensors. Third-party dry-contact state sensors
require the NetBotz Dry Contact Cable (NBES0304). Standard
third-party 0-5 V sensors require the NetBotz 0-5 V Sensor Cable
(NBES0305).
NetBotz 455 Installation and Quick Configuration Manual
5
Inventory
Inspect the contents of the package to ensure that the parts included match those
shown below. Report missing or damaged contents to APC or your APC
reseller. However, if damage was due to shipping, immediately report the
damage to the shipping agent.
The shipping and packaging materials are recyclable. Please save
them for later use or dispose of them appropriately.
6
NetBotz 455 Installation and Quick Configuration Manual
Item
Description

NetBotz Room Monitor 455

Bracket mounting plate for electrical boxes

Extender arms

Ball-joint adjuster arms

T-bar mounting plate

Rubber bracket cover

Mounting plate

Cable retainer

Mounting screw wall anchors

Extender arm set screw

203-mm (8-in) tie wraps

Adhesive cable tie holders

13-mm (0.5-in) machine screws (for electrical box)

19-mm (0.75-in) sheet metal screws (for wall or
enclosure)

1.8 m (6-ft) NEMA 5-15P to IEC-320-C13 power cord
(only included with NBWL0456)

1.8 m (6-ft) IEC-320-C13 to IEC-320-C14 power cord
(only included with NBWL0456)

Allen wrench

Netbotz Appliance Utility CD

Power-over-Ethernet injector power supply
(100–250 VAC in, 48 VDC out) (only included
with NBWL0456)
NetBotz 455 Installation and Quick Configuration Manual
7
Installation
Install the NetBotz 455
Choose an installation option that meets your needs. Take the following into
consideration:
Caution: Only connect approved devices to ports on the NetBotz
455 as directed in this manual. Plugging in other devices may result
in equipment damage.
Note: Consider the location of the nearest network port.
Note: Make sure the camera will not be obstructed.
Note: Consider cable routing for all sensors that you plan to
connect to the appliance.
Note: If the direction of airflow is known, the ideal position of the
NetBotz 455 for measuring the airflow is directly facing the
oncoming air.
Electrical box
8
NetBotz 455 Installation and Quick Configuration Manual
Wall
Note: Drill 4.76-mm (3/16-in) pilot holes for wall anchors.
Caution: Do not overtighten the screws.
NetBotz 455 Installation and Quick Configuration Manual
9
Ceiling
10
NetBotz 455 Installation and Quick Configuration Manual
Enclosure
Note: Use a #32 drill to make four 2.94-mm (0.116-in) pilot holes.
NetBotz 455 Installation and Quick Configuration Manual
11
Connect the NetBotz 455 to Your Network
Power-over-Ethernet (PoE) injector
Caution: Before you energize the NetBotz 455, review the
electrical specifications on page 31 to avoid overloading the circuit.
Caution: Be sure the appliance is properly grounded by plugging
the power cord directly into a wall outlet or by verifying the ground
path if you are using a power strip.
Non-PoE-capable hub or switch
PoE-capable hub or switch
To appliance 10/100 Base-T network port
12
NetBotz 455 Installation and Quick Configuration Manual
Connect Sensors to Sensor Ports
This procedure applies to the following sensors, which are supported by the
NetBotz 455 and connect to the sensor ports:
• Temperature Sensor (AP9335T)
• Temperature/Humidity Sensor (AP9335TH)
• NetBotz Vibration Sensor (NBES0306)
• NetBotz Smoke Sensor (NBES0307)
• NetBotz Spot Fluid Sensor (NBES0301)
• NetBotz 0-5 V Sensor Cable (NBES0305)
• NetBotz Door Switch Sensor for APC Racks (NBES0303)
• NetBotz Door Switch Sensor for Rooms or Third Party Racks
(NBES0302)
• NetBotz Dry Contact Cable (NBES0304)
For sensors that connect to A-Link ports (Temperature
Sensors with Digital Display [AP9520T] and Temperature/
Humidity Sensors with Digital Display [AP9520TH]), see
“Connect Sensors and Sensor Pods to A-Link Ports” on
page 14.
Connect APC and third-party sensors to the four sensor ports labeled Sensors
on the NetBotz 455.
• Third-party dry contact sensors require the NetBotz Dry Contact Cable
(NBES0304). To connect a sensor to the cable, follow the instructions
provided with the sensor and the instructions provided with the cable.
• Standard third-party 0-5 V sensors require the NetBotz 0-5 V Sensor
Cable (NBES0305). To connect a sensor to the cable, follow the
instructions provided with the sensor and the instructions provided with
the cable.
• If a sensor cable is not long enough, use an RJ-45 coupling (provided
with some sensors) and standard CAT-5 cabling to extend the cable up to
15 m (50 ft) for a Temperature/Humidity Sensor (AP9335TH) or a
Temperature Sensor (AP9335T) and up to 30.5 m (100 ft) for all other
supported sensors.
NetBotz 455 Installation and Quick Configuration Manual
13
Connect Sensors and Sensor Pods to A-Link Ports
You can cascade up to a combined total of two NetBotz Rack Sensor Pod 150s
(NBPD0150) and NetBotz Room Sensor Pod 155s (NBPD0155) and up to a
combined total of eight Temperature Sensors with Digital Display (AP9520T)
and Temperature/Humidity Sensors with Digital Display (AP9520TH). You
cannot cascade appliances. Use one appliance per system. A-Link is an APC
proprietary CAN (Controller Area Network) bus. Devices compatible with
A-Link are not Ethernet devices and cannot coexist on an Ethernet bus with
other networking devices, such as hubs and switches.
Before performing this procedure, follow the installation instructions provided
with the devices you are cascading.
1. Connect sensors
and sensor pods to
the appliance as
shown.
– Use CAT-5 (or
equivalent)
Ethernet patch
cables (.
Caution: Do not
use crossover
cables.
– Connect to in
and out ports as
shown.
– The maximum
combined length
of all A-Link
cables must not
exceed 1000 m
(3,280 ft).
2. Plug an A-Link
terminator into the
unused A-Link
port ().
14
NetBotz Room
Monitor 455
(NBWL0455)
NetBotz
Rack Sensor
Pod 150
(NBPD0150)
NetBotz
Rack Sensor
Pod 150
(NBPD0150)
Temperature/
Humidity
Sensor
(AP9520TH)
NetBotz 455 Installation and Quick Configuration Manual
Adjust the Lens
View the camera feed during
the adjustment of the camera in
order to correctly adjust the
focus of the feed and field of
view settings.
lens housing
To access the adjustment
screws, remove the lens
housing by turning the lens
housing counter-clockwise
until the latches disengage.
unlock
lock
aperture
To reattach the lens housing,
engage the latches and rotate
the housing clockwise until a
click is heard.
To adjust the aperture of the
lens, rotate the aperture ring
clockwise to increase the
aperture or counter-clockwise
to reduce the aperture.
field of view
fine-focus
To adjust the focus and field of
view settings:
1. Loosen the adjustment
screw by turning it
counter-clockwise.
2. Rotate the lens rings to the
desired position.
3. Tighten the adjustment
screw by turning it
clockwise.
NetBotz 455 Installation and Quick Configuration Manual
15
Initial Configuration
Note: Disregard the procedures in this section if you have APC
InfraStruXure Central as part of your system. See the documentation
for your InfraStruXure device for more information.
Overview
You must configure the following TCP/IP settings before the appliance can
operate on a network:
• IP address of the appliance
• Subnet mask
• Default gateway
Note: If a default gateway is unavailable, use the IP address
of a computer that is located on the same subnet as the
appliance and that is usually running. The appliance uses the
default gateway to test the network when traffic is very light.
Obtain network settings using DHCP
By default, your appliance obtains its network settings using DHCP. When you
connect the appliance to your network and apply power to the unit, it
automatically attempts to contact a DHCP server. The appliance waits 30
seconds for a response. If the DHCP server is configured to provide a hostname,
the appliance requests either its configured hostname or netbotzxxxxxx
(where xxxxxx is the last 6 digits of the MAC address of the appliance) as a
hostname associated with the IP address granted by the DHCP server. This
enables you to use a Web browser to connect to the appliance using the address
http://netbotzxxxxxx without any additional configuration. The appliance also
requests DNS server addresses, a DNS domain, SMTP server addresses, and
NTP server addresses from the DHCP server.
Install the serial configuration utility and other programs. The APC
Serial Configuration Utility is a Java®-based application that configures the
network settings on your APC appliance. Use the NetBotz Appliance Utility CD
to install the Serial Configuration Utility, as well as the Advanced View (the
monitoring and management console for your NetBotz appliance) and the Java
Runtime Environment (JRE) on your system.
Note: The Java Runtime Environment used by the Advanced View
application is always installed, regardless of whether the installation
target already has a suitable JRE installed.
16
NetBotz 455 Installation and Quick Configuration Manual
• Microsoft® Windows® Systems: To install the applications and the JRE
on a computer running Windows XP SP1 or SP2, or Windows 2000,
place the NetBotz Appliance Utility CD in the CD drive of the computer
that you will use to configure and manage your appliance. The NetBotz
Installer starts automatically. If you have disabled Autorun on your
computer, click Start > Run, type x:\av\windows\install.exe
in the Open field (where x is the drive letter assigned to your CD drive)
and click OK. Follow the prompts to complete the installation of your
software.
• Linux Systems: To install the applications and the JRE on a computer
running Red Hat® Enterprise Linux® 4 or Fedora™ Core 4 or later, place
the NetBotz Appliance Utility CD in the CD drive of the computer that
you will use to configure and manage your NetBotz appliance. Mount
the drive if necessary. Run install.bin from the Linux subdirectory
on the CD. For example, if you are using Linux and you mounted the CD
drive as /mnt/cdrom, execute the following command:
sh /mnt/cdrom/linux/install.bin
Follow the prompts to complete the installation of your software.
Configure network settings using the Serial Configuration Utility
To configure your appliance using the Serial Configuration Utility:
1. Click Start > Programs > APC > Serial Configuration > Serial
Configuration Utility to start the Serial Configuration Utility.
2. Connect one end of a USB cable to your computer and the other end of
the cable to the Console port on the NetBotz appliance.
3. Plug the power cord provided with your NetBotz appliance into a wall
outlet, and then connect it to the AC line inlet.
Note: This power cord is to be used only with APC NetBotz
products.
The green Power LED illuminates immediately after you apply power to
the appliance. The unit can take up to two minutes to initialize,
depending on appliance configuration. The red Alert LED illuminates
when the appliance detects an alert condition. Click Next to continue.
4. The Serial Configuration Utility automatically scans your system COM
ports to determine if an APC appliance is connected to the network. If an
APC appliance is discovered, the appliance is listed in the Device column
of the window. Select the radio button for the appliance to configure and
click Next to continue.
NetBotz 455 Installation and Quick Configuration Manual
17
Note: If the COM port associated with the port to which your
USB cable is connected is currently in use by another
application, the message beside the COM port in the Owner
column indicates that the port is not available. To correct this,
close the application that is using the COM port and click
Scan Serial Ports.
5. The Root Password window appears. Enter the administrator account
password for this appliance (apc, by default) and click OK.
6. Specify whether to use DHCP to specify the network settings of your
appliance. Click Yes or No, and click Next to continue.
7. The utility scans the appliance and displays the network settings stored
on the appliance. The network settings are divided into Ethernet Card
Settings and DNS Settings.
8. Specify the Ethernet Card settings.
– To use network settings assigned by a DHCP server, select Configure
automatically via DHCP.
– To specify network settings for use by this appliance, select Configure
using these settings and provide an IP address, subnet mask, and
gateway address for the appliance. Specify a NAT proxy name or IP
address to be used by a NAT Proxy server in your network to allow
users to connect to the appliance from outside the firewall. You can also
specify speed and duplex settings for use by this interface, or use the
default setting, Auto Negotiate.
9.
Specify the DNS Settings.
– To use DNS Settings provided by your DHCP server, check Use DHCP
DNS Settings.
– To specify DNS Settings for this appliance manually, clear the Use
DHCP DNS Settings checkbox and provide the domain and DNS
server information.
10. Click Next to save your configuration settings. Click Finish to close the
Serial Configuration Utility.
11. Test the IP connection of the APC appliance. Start your Web browser and
type the IP address of the appliance into the address field. Press Enter. If
the APC appliance is online and properly configured, the Basic View
displays in the browser window.
18
NetBotz 455 Installation and Quick Configuration Manual
Install a wireless network device
You can install a third-party wireless network device by connecting it to the
Ethernet port on the appliance using an Ethernet cable. APC currently supports
the D-Link DWL-G820, a wireless Ethernet bridge.
To install and configure a third-party wireless network device, see
the instructions provided with that device.
The APC Configuration Wizard
Use the Configuration Wizard to configure the following settings on your
appliance:
• Domain Name Server Settings
• Clock and Calendar Settings
• Region Settings
• Administrator User ID and Password
• E-Mail Settings
• E-Mail Alert Notification Recipients
The Configuration Wizard downloads the latest available version of BotzWare
to your appliance.
When you finish configuring your appliance with the Wizard, your appliance
monitors your environment for lack of adequate air flow and for changes in
temperature and humidity and detects motion in the area in which the camera is
located. Alert conditions detected by any of these sensors generate an e-mail to
send to a specified e-mail address.
The Configuration Wizard runs each time you use the Advanced View with
your APC appliance until you complete all of the steps in the Wizard or check
Don’t Show Configuration Wizard Next Time. You can run the Wizard again
by selecting Configuration Wizard from the Advanced View Tools pull-down
menu.
NetBotz 455 Installation and Quick Configuration Manual
19
Access an Appliance
Overview
After the appliance is running on your network, you can access the configured
appliance through the Basic View or the Advanced View.
Administrator account user ID and password
Your NetBotz appliance has a pre-configured Administrator account. The User
ID and Password for this account are:
• User ID: apc
• Password: apc
Note: To increase security, be sure to use the Advanced View
Users task to change the default User ID and Password for the
Administrator account.
Root account user ID and password
Your NetBotz appliance has a pre-configured root account. The root account is
used only for appliance communications that are performed using the USB
Console Port, e.g., when you use the Serial Configuration Utility to specify
network settings. The default User ID and Password for this account are:
• User ID: root
• Password: apc
Note: You cannot change the root account User ID. To
increase security, use the Advanced View Change Root
Password Tool to change the default root account password.
20
NetBotz 455 Installation and Quick Configuration Manual
Lost password recovery
To recover from a lost password:
1.
Locate the reset switch on the bottom of the appliance.
2. Use a thin wire such as a paper clip to press the reset switch for 10
seconds. This causes the system to restart.
3. Once the system restarts, login within two minutes using the default login
values:
– For Advanced View:
• User ID: apc
• Password: apc
– For the console:
• User ID: root
• Password: apc
Note: If you do not log in within two minutes after holding
down the reset switch, you must repeat the procedure.
4.
After you log in, change the password to increase security.
Basic View
Use the Basic View to view the current sensor data, image capture, and other
appliance data in a HTML-based interface. Use the Basic View to perform basic
appliance configuration. The configuration tasks available from the Basic View
are limited and are included for initial appliance installation and setup. This
view is provided to allow you to use a Web browser to view appliance status.
APC supports the following Web browsers:
• Microsoft Internet Explorer® 5.5 and higher (on Windows operating
systems only)
• Mozilla®-based browsers that support Firefox® 1.x (on all operating
systems)
• Netscape® 7.x and higher (on all operating systems)
Note: Other commonly available browsers also may work but
have not been fully tested by APC.
NetBotz 455 Installation and Quick Configuration Manual
21
Advanced View
Use the Advanced View to view sensor data, camera images, and other
appliance data in a custom Java application. You can also use the Advanced
View to generate relay output actions and configure all appliance features. The
Advanced View is a stand-alone application that must be installed on a
supported network-attached computer.
For more information on the Basic View or the Advanced View, see
the NetBotz Appliance User’s Guide.
APC Quick Configuration
Once you configure, install, and apply power to your appliance, use the
Advanced View to perform the following procedures.
• Configure Appliance Settings: Configure the appliance Clock, DNS,
Region, Network Interface (hostname, NAT proxy, and speed and duplex
settings), E-mail Servers, and Proxy settings.
• Configure Alert Actions: Configure the Play Audio Alert and Primary
E-mail Notification alert actions.
22
NetBotz 455 Installation and Quick Configuration Manual
Configure appliance settings
Open the Advanced View and perform the following Appliance Settings tasks.
The icons associated with each task are located in the Configuration pane, in the
Appliance Settings region.
1. Set the Clock settings. By default, your appliance synchronizes the
system clock with the default NTP servers. If network access to these
servers is not permitted, double-click on the Clock icon and specify your
NTP server address or manually specify clock settings.
2. Set DNS settings. Double-click the DNS icon and specify the DNS
Domain and at least one DNS Server address.
3. Set the Region settings. Double-click the Region icon and set Locale and
Time Zone. The default settings are US and Central Standard Time.
4. Specify a hostname for your appliance. Double-click on Network
Interfaces and specify a hostname for your appliance. Optionally,
specify a NAT proxy name or IP address to be used by a NAT Proxy
server in your network to allow users to connect to the appliance from
outside the firewall. You can also specify speed and duplex settings for
use by this interface, or use the default setting, Auto Negotiate.
5. Assign a unique User ID and Password to the Administrator account. By
default, User ID and Password for the Administrator account are both
apc. To increase security, double-click the Users icon, double-click APC
Admin Account, and specify a unique User ID and password for the
administrator account.
6. Set your E-mail Server settings. This is the e-mail server that your
appliance uses to deliver e-mail alert notifications. Double-click the
E-mail Servers icon, and configure the following settings:
– (Optional) Provide a From address.
– In the SMTP server field, type the hostname or IP address of your
SMTP server (for example, mail.yourcompany.com).
– If necessary, specify a Port value. (25, by default).
– Select an SSL option for authentication and certificate verification.
Check with your network administrator for further assistance.
– Click Test E-mail Server, type in your e-mail address, and click OK.
An e-mail is sent to your address when an alert is detected. Confirm
that you received the test e-mail and continue.
7. If your network uses an HTTP or Socks proxy server, double-click the
Proxy icon and specify your Proxy settings. If you are unsure whether
you use an HTTP or Socks proxy, check with your network administrator.
NetBotz 455 Installation and Quick Configuration Manual
23
Configure alert actions
You can configure your appliance to play audio alert notifications through the
headphone/speaker jack on your Camera Pod 160 or Camera Pod 120 or to send
an e-mail alert notification to your e-mail address when sensor thresholds are
violated.
Open the Advanced View and perform the following Pod/Alerts Settings tasks.
The icons associated with each task are located in the Configuration pane, in the
Pod/Alerts Settings region.
1. Open the Alert Actions task. Double-click the Alert Actions icon to open
the Alert Action Configuration window.
2. Click Add... to open the Select Alert Action window, select Play Audio
Alert and click OK to open the Add Alert Action window.
3. In the Alert Action Name field, type a name for this alert action (for
example, Play Audio Alert).
4. Select your Camera Pod from the Output Device drop box. Optionally,
adjust the Volume% setting.
5. Click OK to close the Add Alert Action window and continue. Your
newly created alert action is included in the list of Alert Actions.
6. Select Primary E-mail Notification from the list of defined alert actions
and click Edit.
7. Check Include a sound clip with the alert. This ensures that any alert
e-mailed to you includes a sound clip with any camera images that are
delivered. You can disable this option later, if the file size of alert
notifications is too large.
8. Click Add..., type your e-mail address in the Add E-mail Address
window, and click OK.
9.
Click OK to close the Edit Alert Action window and continue.
10. Click OK to close the Alert Action Configuration window.
24
NetBotz 455 Installation and Quick Configuration Manual
Upgrade Options
Software Feature Upgrades
The BotzWare on your appliance can be upgraded using the Upgrade task in the
Advanced View. The following software packs can be added to your appliance.
• Advanced Software Pack, which includes the following features:
– Block out masking for camera images
– Digitally signed clips
– Enhanced audio features
– Detailed appliance location information
– Increased number of definable users and user capabilities
Note: The features of this pack are standard on the
NetBotz 550.
• 5 Node Scanner/IPMI Pack, which provide IPMI and SNMP scanner
integration
Note: When you upgrade your appliance, the connected pods
are automatically updated. If your network includes more
than one appliance, you must perform the upgrade on all
appliances. Valid data is not available during the upgrade.
Hardware Upgrades
You can upgrade your NetBotz appliance hardware in the following ways:
• Add Camera Pod 160s, Sensor Pod 150s, Sensor Pod 155s, and CCTV
Adapter Pod 120s to your NetBotz appliance
• Add a supported USB modem to a USB port on your appliance
• Add a supported USB digital I/O device to a USB port on your appliance
• Add supported USB-to-serial port device on your appliance
Note: The NetBotz Room Monitor 455 supports the NetBotz
Sensor Pod 120 and the NetBotz Camera Pod 120.
NetBotz 455 Installation and Quick Configuration Manual
25
Add pods to your appliance
The NetBotz Room Monitor 455 supports the following pods:
• A combined total of two Camera Pod 160s, Camera Pod 160s, and CCTV
Adapter Pod 120s.
• A combined total of two Sensor Pod 150s, Sensor Pod 155s,
Sensor Pod 120s, and 4-20mA Input Pod 120s.
Camera Pods, Sensor Pod 120s, and 4-20mA Input Pod 120s can be connected
directly to the appliance USB port, or you can connect a USB hub to your
appliance and then connect pods to the hub. Hubs can also be daisy chained,
and pods can be connected to the daisy-chained hubs as long as the pod is no
more than the fifth device in the chain.
Note: Due to power requirements, Camera Pod 160s, Sensor Pod
120s, CCTV Adapter Pod 120s, and 4-20mA Input Pod 120s must be
connected either directly to the USB port at the appliance or to a USB
hub receiving power from an external source. RS232-based sensors
or devices can be connected to unpowered USB hubs.
As pods are connected to your appliance, they automatically appear in the
Navigation pane in both the Basic and Advanced View interfaces. Newly added
pods are labeled by their pod type and their serial number.
Once a pod is added, you can change its label using either the Basic View or the
Advanced View.
• Once connected, CCTV Adapter Pod 120s require additional
configuration before they can be used.
For more information, see “Install and configure a CCTV
adapter pod 120” on page 27.
• If you connect a pod and then disconnect it, its entry in the Navigation
pane in the Advanced View is grayed out. If you reconnect a
disconnected pod, its Navigation pane entry becomes active again.
26
NetBotz 455 Installation and Quick Configuration Manual
Install and configure a CCTV adapter pod 120. To install a CCTV
Adapter Pod 120, connect your video source to the appropriate DIN, BNC, or
RCA video input jack on the pod. Use the USB cable to connect your pod to
your NetBotz appliance, or to a USB hub connected to the appliance. To reduce
radio frequency noise and emissions from the USB cable, clamp one clamp-on
ferrite onto the USB cable within 51-76 mm (2-3 in) of the end that connects to
the pod, and the second clamp-on ferrite onto the USB cable within 51-76 mm
(2-3 in) of the end that connects to your appliance or to the USB hub.
After you connect your CCTV Adapter Pod 120 and video source to your
appliance, use the Advanced View to configure the pod.
To configure your pod:
1. Start the Advanced View. From the Appliance drop-down list, select the
IP address of the appliance to which you have connected the CCTV
Adapter Pod 120. Log in to the appliance using a user account that has
administrator privileges. After you log in, confirm that the newly
connected CCTV Adapter Pod 120 appears in the Navigation Pane. The
default label for CCTV Adapter Pod 120s is CCTV Video Pod serial,
where serial is the serial number of the pod.
2. Select the Configuration button and double-click the Camera Pods icon
(located in the Pod/Sensor Settings portion of the Configuration pane).
3. In the Camera Pod Configuration pane, select the entry that corresponds
to the CCTV Adapter Pod 120 and then click Capture.
4. The Camera Capture Settings window opens. In addition to the fields that
are available when you use this window to configure Camera Pod 160s,
one additional control is available when you configure a CCTV Adapter
Pod 120:
– Video Format: Used to specify the format in which video is
transmitted by the video source. Available selections include:
NTSC-M, NTSC-Japan, PAL-B, PAL-D, PAL-G, PAL-H, PAL-I,
PAL-M, PAL-N Combination, and SECAM.
5. Use the controls in the Camera Capture Settings window to configure the
camera and image capture settings for use with the pod. To see an
example of an image capture using the currently selected Video Format,
Brightness, Contrast, and Image Quality settings, click Apply. The
sample image in the Capture window will be updated using the new
values. When you are finished, click OK to save your changes to the
appliance.
Your video source should now appear in the Advanced View Cameras pane.
Once configured, you can use the video source in the same ways you use
Camera Pod 160s.
NetBotz 455 Installation and Quick Configuration Manual
27
Connect a USB modem
You can enhance the network communication capabilities of your appliance by
connecting a supported USB modem to your appliance. The following USB
modems are supported for use with the appliance:
• MultiTech® MultiModem® GPRS
• MultiTech MultiMobile™ USB
• Option GlobeSurfer® iCon
Connect the USB modem to your appliance, or to a USB hub that is connected
to the appliance. Once the modem is recognized as a serial port by the
appliance, use the Basic View Setup view or the Advanced View Serial Devices
task to specify the modem that is associated with the serial port. Once you
specify the modem model, use the Advanced View PPP/Modem task to
configure your appliance for PPP communications.
To uninstall your USB modem, use the Serial Devices task in the Advanced
View to remove the device.
Connect a USB digital I/O device
You can increase the number of dry contact sensors that can be connected to
your appliance by connecting a supported USB digital I/O device to your
appliance. The following USB digital I/O devices are supported for use with the
appliance:
• Sealevel® SeaLINK PIO-48 (adds 48 digital I/O connections)
• Sealevel SeaI/O 462U (adds 96 digital I/O connections)
• Sealevel SeaI/O 463U (adds 96 digital I/O connections)
• Sealevel SeaI/O 450U (adds 96 digital I/O connections)
To connect a USB digital I/O device to your appliance:
1. Remove power from the appliance.
2. Connect the USB digital I/O device to your appliance, or to a USB hub
that is connected to the appliance.
3. Apply power to the appliance.
4. Once the appliance has finished booting up, power for the digital I/O
device will be recognized at a serial port by the appliance. Use the Basic
View Setup view or the Advanced View Serial Devices task to specify the
digital I/O device that is associated with the serial port.
5. Use the Advanced View Dry Contacts task to configure any dry contact
sensors you have connected to your digital I/O device.
To uninstall your USB digital I/O device, use the Serial Devices task in the
Advanced View to remove the device.
28
NetBotz 455 Installation and Quick Configuration Manual
Connect an APC Switched Rack PDU
To connect an APC Switched Rack PDU 79xx to your appliance, connect a
USB-to-serial cable (NBAC0226, available from APC and APC resellers) to
the RJ-12-to-DB9 serial cable (940-0144A) included with the Rack PDU.
Connect your USB-to-serial cable to your appliance, or to a USB hub that is
connected to the appliance.
Once you connect the USB-to-serial cable to your appliance, you can connect
the Rack PDU to the RJ-12-to-DB9 serial cable for use with your appliance.
Supported APC Switched Rack PDUs. APC Switched Rack PDUs with
firmware version 2.74 and lower are supported at this time.
Install intelligent power strips. Connect the intelligent power strip to a
serial port on your USB-to-serial cable. Use the Basic View Setup view or the
Advanced View Serial Devices task to specify which serial port-based sensor
you have connected to the appliance.
The sensor readings associated with the device will appear in the Basic and
Advanced Views once you complete installation.
To uninstall your intelligent power strip, use the Serial Devices task in the
Advanced View to remove the device.
NetBotz 455 Installation and Quick Configuration Manual
29
Connect external sensors
To install an external sensor, plug the sensor into an available External Port on
any Sensor Pod 150, Sensor Pod 155, or Sensor Pod 120.
Note: When connecting a sensor to a Sensor Pod 120, be sure to note
both the sensor pod serial number, located on the back of the pod,
and the number of the External Port on the pod when you connect the
cable. You will need this information when you use the sensor pod
task to configure your appliance. The External Port number is printed
above the port on the pod.
The female connectors on the NetBotz 120 Sensor Pod units are
Version 2, NetBotz DIN standard connectors and can only accept
male, Version 2, NetBotz DIN Sensor Cables. The new Version 3
products use standard RJ-45 connectors.
If the external sensor cable is not long enough, use an Extension Cable for
External Sensors, available in 15 m (50 ft) and 30 m (100 ft) lengths from your
APC reseller, to lengthen the cable.
When you have finished installing external sensors, use the Sensor Pods task to
configure the appliance to use the external sensor. Once you configure your
appliance, an additional temperature sensor appears in the Sensor Data pane
when the pod to which the temperature sensor is connected is selected from the
Navigation pane. Use the Advanced View Sensor Pods task to specify
thresholds for this external sensor.
Clean the NetBotz 455
To clean the device, gently wipe surfaces with a clean, dry cloth.
30
NetBotz 455 Installation and Quick Configuration Manual
Specifications
Electrical
Input voltage, nominal
48 VDC (Power-over-Ethernet)
Maximum power consumption
15 W
Physical
Dimensions (H x W x D)
210 x 170 x 94 mm (8.3 x 6.7 x 3.7 in)
Weight
0.64 kg (1.40 lb)
Environmental
Elevation (above MSL)
Operating
Storage
0 to 3000 m (0 to 10,000 ft)
0 to 15 000 m (0 to 50,000 ft)
Temperature
Operating
Storage
0 to 45ºC (32 to 113°F)
-15 to 65°C (5 to 149°F)
Relative Humidity
Operating
Storage
10 to 90%, non-condensing
10 to 90%, non-condensing
Compliance
Immunity/Emissions
CE, FCC Part 15 Class A, ICES-003 Class A,
VCCI Class A, EN 55022 Class A, EN 55024,
AS/NZS CISPR 22
NetBotz 455 Installation and Quick Configuration Manual
31
Warranty
Two-Year Factory Warranty
This warranty applies only to the products you purchase for your use in
accordance with this manual.
Terms of warranty
APC warrants its products to be free from defects in materials and
workmanship for a period of two years from the date of purchase. APC will
repair or replace defective products covered by this warranty. This warranty
does not apply to equipment that has been damaged by accident, negligence or
misapplication or has been altered or modified in any way. Repair or
replacement of a defective product or part thereof does not extend the original
warranty period. Any parts furnished under this warranty may be new or
factory-remanufactured.
Non-transferable warranty
This warranty extends only to the original purchaser who must have properly
registered the product. The product may be registered at the APC Web site,
www.apc.com.
Exclusions
APC shall not be liable under the warranty if its testing and examination
disclose that the alleged defect in the product does not exist or was caused by
end user’s or any third person’s misuse, negligence, improper installation or
testing. Further, APC shall not be liable under the warranty for unauthorized
attempts to repair or modify wrong or inadequate electrical voltage or
connection, inappropriate on-site operation conditions, corrosive atmosphere,
repair, installation, exposure to the elements, Acts of God, fire, theft, or
installation contrary to APC recommendations or specifications or in any event
if the APC serial number has been altered, defaced, or removed, or any other
cause beyond the range of the intended use.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, BY
OPERATION OF LAW OR OTHERWISE, OF PRODUCTS SOLD,
SERVICED OR FURNISHED UNDER THIS AGREEMENT OR IN
CONNECTION HEREWITH. APC DISCLAIMS ALL IMPLIED
WARRANTIES OF MERCHANTABILITY, SATISFACTION AND
FITNESS FOR A PARTICULAR PURPOSE. APC EXPRESS
WARRANTIES WILL NOT BE ENLARGED, DIMINISHED, OR
AFFECTED BY AND NO OBLIGATION OR LIABILITY WILL ARISE
OUT OF, APC RENDERING OF TECHNICAL OR OTHER ADVICE
32
NetBotz 455 Installation and Quick Configuration Manual
OR SERVICE IN CONNECTION WITH THE PRODUCTS. THE
FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE
AND IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES. THE
WARRANTIES SET FORTH ABOVE CONSTITUTE APC’S SOLE
LIABILITY AND PURCHASER’S EXCLUSIVE REMEDY FOR ANY
BREACH OF SUCH WARRANTIES. APC WARRANTIES EXTEND
ONLY TO PURCHASER AND ARE NOT EXTENDED TO ANY THIRD
PARTIES.
IN NO EVENT SHALL APC, ITS OFFICERS, DIRECTORS,
AFFILIATES OR EMPLOYEES BE LIABLE FOR ANY FORM OF
INDIRECT, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES,
ARISING OUT OF THE USE, SERVICE OR INSTALLATION, OF THE
PRODUCTS, WHETHER SUCH DAMAGES ARISE IN CONTRACT
OR TORT, IRRESPECTIVE OF FAULT, NEGLIGENCE OR STRICT
LIABILITY OR WHETHER APC HAS BEEN ADVISED IN ADVANCE
OF THE POSSIBILITY OF SUCH DAMAGES. SPECIFICALLY, APC IS
NOT LIABLE FOR ANY COSTS, SUCH AS LOST PROFITS OR
REVENUE, LOSS OF EQUIPMENT, LOSS OF USE OF EQUIPMENT,
LOSS OF SOFTWARE, LOSS OF DATA, COSTS OF SUBSTITUENTS,
CLAIMS BY THIRD PARTIES, OR OTHERWISE.
NO SALESMAN, EMPLOYEE OR AGENT OF APC IS AUTHORIZED
TO ADD TO OR VARY THE TERMS OF THIS WARRANTY.
WARRANTY TERMS MAY BE MODIFIED, IF AT ALL, ONLY IN
WRITING SIGNED BY AN APC OFFICER AND LEGAL
DEPARTMENT.
Warranty claims
Customers with warranty claims issues may access the APC customer support
network through the Support page of the APC Web site, www.apc.com/
support. Select your country from the country selection pull-down menu at the
top of the Web page. Select the Support tab to obtain contact information for
customer support in your region.
NetBotz 455 Installation and Quick Configuration Manual
33
Radio Frequency Interference
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to
operate this equipment.
USA —FCC
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with this
user manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference. The user
will bear sole responsibility for correcting such interference.
After an electrostatic discharge (ESD) event, the appliance may require up to 2
minutes to restart services that are necessary for normal operation. During this time,
the Web interface of the appliance will be unavailable. If any necessary services or
devices external to the appliance, such as a DHCP server, were affected by the ESD
event, these devices also need to restart properly.
Canada— ICES
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du
Canada.
Japan—VCCI
This is a Class A product based on the standard of the Voluntary Control Council for
Interference by Information Technology Equipment (VCCI). If this equipment is
used in a domestic environment, radio disturbance may occur, in which case, the
user may be required to take corrective actions.
この装置は、情報処理装置等電波障害自主規制協議会(VCCI)の基準
に基づくクラス A 情報技術装置です。この装置を家庭環境で使用すると、電波
妨害を引き起こすことがあります。この場合には、使用者が適切な対策を講ず
るように要求されることがあります。
Taiwan—BSMI
警告使用者 :
這是甲類的資訊產品 , 在居住的
環境中使用時 , 可能會造成射頻
干擾 , 在這種情況下 , 使用者會
被要求採取某些適當的對策。
Australia and New Zealand
Attention: This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate
measures.
European Union
This product is in conformity with the protection requirements of EU Council
Directive 2004/108/EC on the approximation of the laws of the Member States
relating to electromagnetic compatibility. APC cannot accept responsibility for any
failure to satisfy the protection requirements resulting from an unapproved
modification of the product.
This product has been tested and found to comply with the limits for Class A
Information Technology Equipment according to CISPR 22/European Standard EN
55022. The limits for Class A equipment were derived for commercial and industrial
environments to provide a reasonable protection against interference with licensed
communication equipment.
Attention: This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate
measures.
APC Worldwide Customer Support
Customer support for this or any other APC product is available at no charge in any of
the following ways:
•
Visit the APC Web site to access documents in the APC Knowledge Base and to
submit customer support requests.
– www.apc.com (Corporate Headquarters)
Connect to localized APC Web sites for specific countries, each of which
provides customer support information.
– www.apc.com/support/
Global support searching APC Knowledge Base and using e-support.
•
Contact the APC Customer Support Center by telephone or e-mail.
– Local, country-specific centers: go to www.apc.com/support/contact for
contact information.
For information on how to obtain local customer support, contact the APC
representative or other distributors from whom you purchased your APC product.
Entire contents copyright 2008 American Power Conversion Corporation. All rights reserved.
Reproduction in whole or in part without permission is prohibited. APC, the APC logo, NetBotz, and
InfraStruXure are trademarks of American Power Conversion Corporation. All other trademarks, product
names, and corporate names are the property of their respective owners and are used for informational
purposes only.
990-3295C-001
*990-3295C-001*
12/2008