Arctic Air Refrigerator Refrigerator User Manual

ARCTIC AIR
COMMERCIAL
REFRIGERATOR/FREEZER
Table
of Contents
Product Registration
...........................................
Important
Safety Instructions
.............................
Electrical
Information
..........................................
2
2
2-3
Caster
3-4
Installation
and Setup
.............................
Appliance
Start-Up ..............................................
Features
...............................................................
Routine
Maintenance
..........................................
4
5-6
6
Reversing
Door ....................................................
Energy Conservation
Measures
.........................
Avoid Service Checklist
......................................
6-7
8
9-10
Wiring
Diagram ....................................................
If You Need Service .............................................
11
12
Warranty
13
...............................................................
P/N: 297121700
(0606)
Product
Remove the door(s) of any appliance
even if it is being discarded.
Registration
that is not in use,
Remove and discard any spacers used to secure the
shelves during shipping. Small objects are a choke
Proper Disposal of Your
Refrigerator/Freezer
The information
contained
Risk
within this Owner's Guide
will instruct you on how to properly operate and care
for your product, Please read through the information
contained in your literature pack to learn more about
your new appliance, The serial plate is located on the
inside left wall of unit,
Record
Your Model and Serial
Record
the Model
in the space
No. and
provided
Serial
of child
entrapment.
Child entrapment
and suffocation
are not
problems of the past.Junked
or abandoned
refrigerators
or freezer are stilldangerous
even if they will sit for 'just a few days." If
you are getting rid of your old refrigerator or
freezer, please follow the instructions
below
to help prevent accidents.
BEFORE YOU THROW AWAY YOUR
OLD REFRIGERATOR/FRE
EZER:
Numbers
No. of this appliance
below.
• Remove
Model No.:
doors.
• Leave shelves
in
place so children
Serial No.:
may not easily
climb inside.
Register Your Product
The self-addressed
(shown
and
above)
returned
PRODUCT
should
to the address
Important
Safety
Read all instructions
REGISTRATION
be filled
in completely,
CARD
J
signed
provided.
Instructions
Electrical
before using this appliance.
These
guidelines
safety
mechanisms
will operate
must
Information
be followed
in the design
to ensure
that
of this appliance
properly.
For Your Safety
Do not store
vapors
and
appliance.
other
or use gasoline
liquids
Read
or other
in the vicinity
product
labels
flammable
r!_Wh_!:t_l
of this or any other
for flammability
and
I_[€
electric shock.
Avoid fire hazard or
Do not use an extension
cord or an adapter plug. Do not remove
any prong from the power cord.
warnings.
Child Safety
•
Grounding
type
wall receptacle
_'_
( DO not under
_'_
/
I | any circumstances
/
_
J_ cut, remove,
|
I /i
I
J
or bypass
I L' •
W
the grounding
prong I
Destroy carton, plastic bags, and any exterior
wrapping material immediately
after the freezer is
unpacked. Children should never use these items to
play. Cartons covered with rugs, bedspreads, plastic
sheets or stretch wrap may become airtight
chambers, and can quickly cause suffocation.
Remove all staples from the carton. Staples can
cause severe cuts, and destroy finishes if they come
in contact with other appliances
this plug.
or furniture.
An empty, discarded ice box, refrigerator,
a very dangerous attraction to children.
hazard to children.
or freezer
is
Po°r_rg
r o :_d_i_nPPi_r;
ng
_
J
•
CASTER
Refer to the serial plate for correct electrical
rating.
The power cord of the appliance is equipped with a
three-prong
grounding plug for protection against shock
hazards. It must be plugged directly into its own
properly grounded three-prong
receptacle, protected
with a 15 amp time delay fuse or circuit breaker. The
receptacle must be installed in accordance with the
INSPECTION
If the voltage
•
performance
may be affected. Operating the appliance
with insufficient power can damage the motor. Such
damage is not covered under the warranty. If you suspect
your voltage is high or low, consult your power company
for testing.
To prevent the appliance from being turned off
•
Check to make sure that you have received
components listed below.
the box containing
D
F
or more, appliance
accidentally, do not plug the unit into an outlet controlled
by a wall switch or pull cord.
DO NOT pinch, knot, or bend the power cord in any
manner.
Other
•
E
A
B
C
D
TOOLS
unit.
NEEDED
_
tools to assemble
and install the casters
to the
_i_
components.
UNCRATING
AND SET-UP
3/8" AND t/2" INCH
SOCKET WRENCH
• Remove carton and all loose parts from inside of the unit.
• Carefully tip the unit onto its back with the help of an
assistant. Lay the unit gently to rest on blocks to avoid
damaging
the condensate
drain hose and the plastic
raceway that covers the evaporator
tubing on the back of
the cabinet.
• Remove
G
CASTER RAIL (2 /
TAPPING PLATE (2)
BOLT (6)
WASHER (6)
You wilI need the following
NOTE: Turning the control to "OFF" turns off the
compressor but does not disconnect power to other
all of the
/
Precautions
NEVER unplug the appliance by pulling on the power cord.
Always grip the plug firmly and pull straight out from the
receptacle.
To avoid electrical shock, unplug the appliance before
cleaning.
electrical
and packaging for damage such as a
damage
is found after uncrating
and request an inspection. Retain atl
the inspection is complete.
PARTS AND ACCESSORIES
•
•
by 10 percent
& SETUP
FOR DAMAGE
Inspect the underside of the cabinet
fork truck can cause. If hidden
immediately call the delivery carrier
packaging and crating materials until
local codes and ordinances.
Consult a qualified
electrician.
Receptacles with Ground Fault Circuit
Interrupters
(GFCI) are NOT RECOMMENDED.
DO
NOT USE AN EXTENSION
CORD OR AN ADAPTER
PLUG.
varies
INSTALLATION
and discard
the four (4) screws
1).
the wood
skid from the bottom
using a 3/8" socket wrench
• Using a large adjustable wrench, remove
two (2) black
plastic
leg levelers
counterclockwise
(see Fig. 2).
UNCRATING
AND SET-UP
Remove carton and all loose parts from inside of the unit.
Carefully tip the unit onto its back with the help of an assistant. Lay the
unit gently to rest on blocks to avoid damaging the condensate drain
hose and the plastic raceway that covers the evaporator tubing on the
back of the cabinet,
•
Remove and discard the wood skid from the bottom and the four (4)
screws using a 3/8" socket wrench (see Fig. 1 )
Using a large adjustable wrench remove and discard the two (2) black
plastic leg levelers by turning it counterclockwise
(see Fig. 2)
and
the
it
1/2" iNCH FIXED
WRENCH
•
•
(see Fig.
and discard
by turning
ADJUSTABLE WRENCH
OR PLIERS
•
SCREWS
WOOD
SKID
Figure 2
Figure 1
CASTER
RAILINSTALLATION
AppliancePlacement
• Place
awasher
ontooneofthesixlongboltsandslideboltthrough
the Leave
aone(1)inchspace
onallsides
andthebackofthe
holelocated
atthefrontofcaster
rail•
cabinet
forease of installation, proper air circulation and
• Alignthecaster
railassembly
withtherighthandsideoftheunit•
connections.
DO NOT block the front grill on
• Aligntheboltwiththethreaded
holeinthefrontrightfootpadofthe electrical
the lower front of your appliance.
Sufficient air circulation
unit•Thread
theboltintotheholeuntilfinger
tight(seeFig.3)•
is essential
for the proper operation
of your appliance.
Choose a place that is near a grounded electrical outlet. For
the most efficient operation, the appliance should be located
where surrounding
temperatures
will not drop below 40°F
(5°C) or exceed 110°F (43°C). Additional compressor heaters
are not recommended•
: :>,
l:
Insulation
The insulated space of this cabinet is sealed to
maintain peak efficiency, Holes drilled in the cabinet
may destroy that seal and damage electrical wiring
located in the insulated space,
Figure
3 o_-
DAMAGED ELECTRICAL WIRING OR WET
REAR
SWIVEL
CASTER
INSTALLATION
• Placea washer
ononeofthesixlongboltsandthenfeedthebolt INSULATION CAUSED BY DRILLING WILL VOID THE
WARRANTY,
through
theholeinoneoftheswivel
casters
(seeFig•4).
• Next,
insert
thatsame
caster
boltthrough
theholeonthemetal
spacer
Appliance
Start-Up
plate
andthenthrutherearholeofthecaster
rail(seeFig.5).
• Thread
thecaster
boltintotheholeinthebottom-most
footpadonthe
unit.
Once the appliance has been located in its permanent
• Tighten
bothtopandbottom
boltssecurely
usinga 1/2inchfixedor location and the proper power and grounding has
socket
wrench,
been provided, the following items must be checked or
• Repeat
thesame
procedure
onthelefthand
side
completed:
Cool Down
%_
I
ii ii/
i
I
_i
i'_
_
SWIVEL
CASTER
Figure 4
FRONT SWIVEL
Thermostat
Settings
The appliance is shipped from the factory with the
thermostat set at about the mid-point of the operating
range, Adjustments colder or warmer can be made
after the appliance has been running for at least 8
hours, Allow at least 8 hours for temperature
stabilization before re-adjusting the thermostat,
Figure 5
CASTER
Period
For safe food storage, allow 24 hours for the appliance
to cool down completely before loading with food,
The appliance will run continuously for the first several
hours, De not place any food in the appliance until
after the first 24 hours of operation,
INSTALLATION
• Place the tapping plate between the front bottom of the cabinet and
caster rails as depicted in Figure 6. Make sure the tapped holes in the
tapping plate align with the center slot in the caster rail.
• Next, place a washer on one of the six long bolts and then feed the bolt
through the hole in one of the swivel casters (see Fig. 4).
• Then, place the spacer plate on the caster and thread the caster bolt
into the hole in the tapping plate•
• Tighten securely using ½" fixed or socket wrench•
• Repeat the same procedure on the left hand side• After installation,
carefully tip the unit up with the help of an assistant•
Tapping Plate
:]:...
:'-7:,,''
Defrost Setting
The appliance is designed to defrost automatically
every 12 hours. To set the time of defrost, wait until
the desired time to defrost. With the notch on the
timer knob aligned with the line on the bracket
(Figure A), turn the defrost timer knob clockwise
slowly. The timer will click several times, then once
loudly, at which point the defrost cycle begins. The
timer knob will advance through the defrost cycle,
then click loudly at the end of the cycle (Figure B).
The appliance will defrost automatically every 12 hours
after the first defrost cycle.
For example, to set the appliance to defrost at 10:00
a.m., turn the timer knob clockwise at 10:00 a.m. until
the timer clicks loudly.The appliance will defrost daily
at 10:00 a.m. and again12 hours later at 10:00 p.m.
Note: The product interior temperature will rise during
the defrost cycle every 12 hours.
Figure 6
Defrost
Timer
BackofUnit
/
4 Swivel
Casters
The appliance comes with 4 swivel casters; 2 with
locks for front of unit and 2 without locks, for the back
of the unit. The casters allow the appliance to be
moved with ease, and then locked into place upon
final destination. (Refer to page 3 for instructions.)
Reversible
Door Lock
The appliance comes with an outer cabinet mounted
door lock and two keys. The lock can be mounted on
either side of the appliance depending on which side
the door swings open. A door mounted lock guard
has been provided for added security. (Refer to page 7
for instructions.)
Figure A
Position of knob
before turning
clockwise
to start defrost
Figure B
Position of knob
at end of defrost cycle.
cycle.
Features
Heavy duty epoxy powder coated adjustable shelv
NSF certified top mounted evaporator
2-1/2" urethane foam cabinet insulation
Torsion spring door closer
Heavy duty swivel casters
17 watt fluorescent lamp
Removable stainless steel drain cover
Adjustable temperature control
NSF certified interior
Stainless steel evaporator housing
Stainless steel toe plate
Heavy duty commercially rated electrical harness
Heavy duty removable stainless steel shelf supper1
Shallow
Shelves
(2) Regular
She
Bottom
The appliance is provided with 4 shelves. One goes
the floor of the cabinet and the other 3 are placed in
the metal side supports wherever they are needed. shallow shelf goes in the upper position.
Reversible
Door
The door can be reversed (See Routine Maintenance
section) to provide either a right-hand swing or a lefthand swing.
Adjustable
Temperature
The adjustable thermostat
left panel inside the unit.
Control
control is located on the top
InteriorThermometer
Theappliance
comeswithathermometer
toshow
internal
temperatures.
Thethermometer
istobehung
fromthetopadjustable
shelfontherighthandside.
1
CondensatePan
Thecondensate
panisinafixedposition
andmustnot
beremoved
fromunderthecabinet.
Ifthepanis
removed,
condensate
willdripontothefloor.
Reversing
Door
This appliance features a door that can provide either
a left hand or right hand opening. It comes from the
factory in the right hand position.
Follow these steps to reverse the opening:
1. With the appliance in a standing upright position,
open the door and remove the toe plate (2 screws
in the upper corners).
2. Slightly loosen the two hex spacers that the toe
plate screws were screwed into.
Interior Light
The appliance is equipped with a 40 watt bulb that
lights up when the door is opened. If bulb goes bad
replace with bulb of same type and wattage. This is a
special bulb with a shatterproof coating. Use an NSF
certified bulb of the same type and wattage (can be
ordered from your Arctic Air Service Center at
1-800-490-9574
1 PIN 2163600900).
Routine
Top
Maintenance
Cleaning the Interior
Be sure to turn the temperature control to off and
unplug the electrical cord. Wash the inside surface of
the storage area with warm water and baking soda
solution (about one tablespoon of baking soda per
quart of water). Rinse thoroughly with clean, warm
water and wipe dry. The procedure can also be used
for cleaning the door gasket. Wipe the stainless steel
cover plates with Magic Clean Stainless Steel Cleanei
(can be ordered from your Arctic Air Service Center at
1-800-490-9574
1 PIN 218490900) or some other
stainless steel cleaner.
Cleaning the Exterior
Wipe the textured cabinet exterior occasionally with a
cloth dampened in mild detergent and water, rinse
and wipe dry with a soft cloth. Wipe the stainless
steel door plate and toe grill with Magic Clean
Stainless Steel Cleaner or some other stainless steel
cleaner. Do not use razor blades or other sharp
instruments that can scratch the appliance surface
when removing adhesive labels. Any glue left from the
tape can be removed with a mixture of warm water
and mild detergent or touch the residue with the
sticky side of tape already removed. DO NOT REMOV
THE SERIAL PLATE.
(2)Hex Head
Spacers
(2) Screws
Toe Plate --
3.
4.
Door
Holding door securely closed, remove three (3) hex
head screws from the top hinge and flat spacer.
Lift appliance door off of bottom hinge and set
aside in a safe place (so it does not fall)
[3) Hex Head --I_@
/
Screws
Flat
Top Hinge_
7- Spacer
J
J
J
Remove top screw from bottom hinge. Remove to_
screw from opposite side of appliance.
9.
Rotate the top hinge to align the mounting
holes.Re-position
the flat spacer between the hinge
and cabinet and install the three (3) hex head
screws.
iii
,!,ge
iii
ToP
Screw _
10. Install hole plugs in each of the hinge holes on
opposite side of cabinet.
11. Re-install toe plate with two (2) screws.
iii
_'"
iii
Door Lock
iii
iii
1.
Spacer
(slightly Ioc
6,
Note :
sened)
Slide bottom hinge onto hex spacer and attach top
screw to cabinet. Retighten both hex spacers.
Hole
BoSom
2.
The lock strike should angle out and away
from the cabinet.
Install the lock strike on the lock side of the
cabinet, using the three (3) tamper resistant
screws. Install the three remaining buttons in the
holes on the opposite side of the cabinet.
Install the lock guard in the side of the door
cabinet by installing the two screws into the
corresponding screw holes.
r z"w'-t'jm L'j_'mThe tamper resistant screws cannot
be removed after the lock strike is secured to the
cabinet.
Cabinet
Lock Strike
Screw
pacer
7.
8.
Remove the top hinge assembly and the bottom
spacer from the door and reverse their position.
making sure the pegs are properly seated in the
peg holes
Rotate the door 180° and re-install on bottom
hinge. Hold door in closed position.
Hole
Resistant
Screws
Energy
Conservation
Measures
The appliance is designed for efficiency with heavy
foam insulation. However, there are things that the
user can do to maintain the appliance in operating
condition:
1.
2.
3.
4.
Do not operate the appliance any colder than
necessary to maintain safe, product storage
temperatures.
Make sure the appliance is located to prevent
direct exposure to sunlight, air ducts, etc.
Keep the door closed except for normal use.
Inspect the door often to see that it self-closes and
the gasket is in good condition.
Do not overstock the product in the cabinet
because it will block the normal air flow.
5.
Have at least annual inspections by a qualified
service company to see that the fan motor is
functioning properly and that the refrigerant charge
is correct.
6.
This appliance operates more efficiently in a cooler
ambient than in a hot ambient. Try to maintain an
ambient below 80°F (2TC) and 65% RH for
maximum efficiency.
Avoid Service Checklist
Before
calling
for service,
includes common
this appliance.
occurrences
OCCURRENCE
APPLIANCE
review this list. It may save you both time and expense.
that are not the result of defective
workmanship
or materials
in
SOLUTION
DOES NOT RUN
• Appliance
may be in defrost cycle,
• Temperature
control
and the compressor
orfan
in or plug may be loose.
• Fuse has blown, orcircuit breaker has tripped. Check/reset
fuse with 15 amp. time delay fuse.
• Power
runs too much or too
outage.
will not run.
is in the OFF position.
• Appliance may not be plugged
pushed into electrical outlet.
Appliance
long.
This list
Check lights. Call local electric
• Room or outside weather
these conditions.
Be sure plug is tightly
circuit breaker or replace
company.
is hot. It is normal for the appliance
• Appliance had recently been disconnected
24 hours to cool down completely.
to work harder under
for a period of time. Appliance
requires
• Large amounts of warm or hot food have been stored recently. Warm food will
cause the appliance to run more until the desired temperature
is reached.
• Door is kept open too long or too frequently. Warm air enters the appliance
time the door is opened. Open the door less often.
Appliance
door may be slightly
open. See Occurrence
section
every
"Door Problems."
• Temperature
control is set too cold. Turn the control knob to a warmer
Allow several hours for the temperature
to stabilize.
setting.
• Appliance gasket is dirty, worn, cracked, or poorly fitted. Clean or change gasket.
Leaks in the door seal will cause appliance to run longer in order to maintain desired
temperature.
Temperatures
inside the
appliance are too cold.
• Temperature
control is set too cold. Turn the control to a warmer
several hours for the temperature
to stabilize.
Temperatures
inside the
appliance are too warm.
• Temperature
control is set too warm. Turn the control
several hours for the temperature
to stabilize.
setting.
Allow
to a colder setting.
Allow
• Door is kept open too long or is opened too frequently.
Warm air enters
appliance every time the door is opened. Open the door less often.
• Door may be open slightly.
See Occurrence
section
"Door Problems."
• Large amounts of warm or hot food may have been stored recently.
appliance has had a chance to reach its selected temperature.
• Appliance has recently been disconnected
24 hours to cool down completely.
• The product
Temperature
of external
appliance surface is warm.
internal
temperature
the
Wait until the
for a period of time. Appliance
will rise during
the defrost
cycle.
• Appliance cabinet is warm to the touch. Appliance
warm air form the inside.
is operating
normally,
requires
removing
OCCURRENCE
SOLUTION
SOUND AND NOISE
Louder
sound levels whenever
appliance
Louder
is on.
sound levels when
compressor
comes
Today's appliances have increased storage capacity and a more even temperature
They require a high speed compressor. This is normal.
Appliance operates at higher pressures during the start of the ON cycle. This is normal
Sound will level off or disappear as appliance continues to run.
on.
Popping or cracking sound
when compressor comes on.
Metal parts undergo expansion and contraction,
Sound will level off or disappear as appliance
Bubbling or gurgling
like water boiling.
Refrigerant
normal.
Vibrating
sound,
or rattling noise.
(used
to cool appliance)
as in hot water pipes. This is normal.
continues to run.
is circulating
throughout
the system.
Appliance is not level. It rocks on the floor when it is moved slightly.
washers to shim up the appliance.
Floor is uneven or weak.
sure floor can adequately
• Appliance
is touching
Appliance rocks on the floor when
support appliance.
the wall.
Reqevel
the appliance
This is
Install leveling
it is moved slightly.
or move appliance
Be
slightly.
WATER/MOISTURE/FROST
INSIDE APPLIANCE
Moisture
forms on inside
appliance
• Weather
normal.
walls.
is hot and humid, which
• Door is slightly
increases
open. See Occurrence
internal
section
• Door is kept open too long or is opened
rate of frost build-up.
This is
"Door Problems."
too frequently.
Open the door less often.
WATER/MOISTURE/FROST
OUTSIDE APPLIANCE
Moisture
forms on outside
appliance.
ODOR
IN APPLIANCE
of
• Door is slightly open, causing the cold air from inside the appliance
moist air from outside. See Occurrence
section 'Door Problems."
• Interior
soda.
needs to be cleaned.
• Foods with strong
DOOR
Clean interior
with sponge,
odors are in the appliance.
to meet warm
warm water, and baking
Cover the food tightly.
PROBLEMS
Door will not close.
LAMP IS NOT ON
• Appliance is not level. It rocks on the floor when it is moved slightly.
can force the cabinet out of square and misalign the door.
• Floor is uneven
or weak.
• Lamp
out. Follow directions
is burned
• No electric current
Does Not Run."
is reaching
10
under "Interior
the appliance.
This condition
Light" in Appliance
See Occurrence
section
Features.
"Appliance
Wiring
Refrigerator
Diagrams
Electrical Circuit
Run
T-_
Bik
Power
[ _Timer.
SeeD
'
i
I
_
I_
_h
_
--___
_
Capacitor-_ _--]
c°mpress°LCompressor
Cold
I Control
___
_1"
Controller.
FL__Yi
I/Yel
L__'
Fan
C10
Defrost
Thermostat
IMPORTANT
if any green grounding wires are removed
during servicing, they must be returned to
their original position and propedy secured.
.4°
Defrost Heater
Wh
_o
Red
Door
Switch
Interior
Light
EC79
Overload
Freezer Electrica|
Circuit
Yellow
T_
Power
Timer
Yel
_
Wh
BIk [- _-->>-Blo---.,--_>>LyoI_:::_
_"
I ""
Compressor
White
',re
Control]
_,
....
Fan
029
Capacitor
OR
Defrost
Thermostat
IMPORTANT
If any green grounding wires are removed
during servicing, they must be returned to
their original position and properly secured.
Defrost Heater
_,_L,
Door
Switch
Red
Interior
Light
Eca0
11
if You Need Service
Avoid Unnecessary
Cost and Inconvenience
Make a few simple checks before calling for service. Common occurrences
in the "Avoid Service Checklist"
included in this owner's guide.
If Service
and their solutions can be found
Is Necessary
Keep your bill of sale, delivery slip, or some other appropriate payment record. The date on the bill
establishes the warranty period should service be required. If service is performed, it is in your best interest
to obtain and keep all receipts. This written warranty gives you specific legal rights. You mayalso have other
rights that vary from state to state. Service under this warranty must be obtained by contacting the
Arctic Air Customer Service Center
In the United States
In Canada:
•
800-490-9574
866-294,9911
12
ARCTIC AIR COMMERCIAL REFRIGERATOR/FREEZER
WARRANTY
ARCTIC AIR (Division of Broich Enterprises, Inc.) warrants every new refrigerator and freezer to be free from
defects in material or workmanship for a period of one (1) year (except as noted in the Special Mobile Use
Warranty below) from the earliest of either: 1) the date of original purchase or; 2) fifteen (15) months after the
manufacturer's ship date of the product ( warranty period ).
This warranty provides:
A. PARTS WARRANTY
ARCTIC AIR will, at its option, repair or replace any part(s), that are found defective during the warranty
addition, ARCTIC AIR warrants that the compressor shall be free from defects for an additional four (4)
beyond the expiration of the warranty period or for a total period of five (5) years. Warranty replacement
must be arranged by calling the Customer Service Center at 1-800-490-9574 ( in the United States and
Rico ) and 1-866-294-9911 ( in Canada ).
period. In
years
parts
Puerto
B. LABOR WARRANTY
ARCTIC AIR will, at its option, provide or pay for the labor to repair or replace the part(s) or product defect during
the warranty period. Warranty labor must be arranged by calling the Customer Service Center at 1-800-490-9574
( in the United States and Puerto Rico ) and 1-866-294-9911 ( in Canada ).
C. SPECIAL MOBILE USE WARRANTY
ARCTIC AIR warrants every new refrigerator and freezer operated by a concessionaire or vendor in a trailer,
motorized vehicle or at varying locations for a period of one (1) year for the part(s) and ninety (90) days for labor
to repair or replace, at Arctic Air's option, the warranty part(s). In addition, ARCTIC AIR warrants that the
compressor shall be free from defects for a total period of five ( 5 ) years. This warranty will be effective with the
earliest of either: 1) the date of original purchase or ; 2) fifteen (15) months after the manufacturer's ship date of
the product. Any labor to remove or expose or make the refrigerator or freezer available for service under this
warranty shall be at the user's expense.
D. CONDITIONS
Service under this warranty must be performed by a preferred service company arranged by the Customer
Service Center at 1-800-490-9574 ( in the United States and Puerto Rico ) and 1-866-294-9911 ( in Canada ).
The user must give the preferred service company prompt notice and access to the product when service is
needed.
E. LIMITATIONS AND EXCLUSIVE WARRANTY
Normal wear and tear and gradual deterioration is excluded from this warranty. This parts and labor warranty is
the sole and exclusive warranty remedy offered by ARCTIC AIR. ALL OTHER WARRANTIES, EITHER EXPRESS
OR IMPLIED, ARISING UNDER LAW OR EQUITY OR CUSTOM OF THE TRADE INCLUDING BUT NOT
LIMITED TO WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE
EXCLUDED. NEITHER ARCTIC AIR NOR ITS SERVICING AGENT SHOULD BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL LOSS OR DAMAGES (INCLUDING BUT NOT LIMITED TO FOOD OR
PRODUCT LOSS, PERSONAL INJURY OR PROPERTY DAMAGE) WHETHER BASED ON CONTRACT OR
TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) ARISING OUT OF THE EQUIPMENT OR
SERVICE PROVIDED HEREUNDER. THIS WARRANTY DOES NOT APPLY ARCTIC AIR PRODUCTS SOLD
OUTSIDE THE UNITED STATES, CANADA, OR PUERTO RICO. THIS WARRANTY DOES NOT COVER:
•
FREIGHT DAMAGE
•
FOOD
•
NON-FACTORY
LOSS
APPROVED
REVISIONS
OR MODIFICATIONS
13
Download PDF

advertising