WASHING MACHINE
SERVICE MANUAL
CAUTION
READ THIS MANUAL CAREFULLY TO DIAGNOSE TROUBLES
CORRECTLY BEFORE OFFERING SERVICE.
MODEL : WD-14311(6)RD/WD-1481RD
WD-12311(6)RD
WD-14312(7)RD/WD-14310(5)RD
WD-12312(7)RD/WD-12310(5)RD
WD-10PFD, 10PFP
WD-14311RDA
WD-1485RD/WD-1488RD
AWD-14312(7)RD
AWD-12312(7)RD
OCT. 2004 PRINTED IN KOREA
P/No.:3828ER3035G
CONTENTS
1. SPECIFICATION............................................................................................................................3
2. FEATURES & TECHNICAL EXPLANATION ................................................................................ 4
3. PARTS IDENTIFICATION ............................................................................................................ 6
4. INSTALLATION ............................................................................................................................. 7
5. OPERATION ................................................................................................................................10
6. WIRING DIAGRAM / PROGRAM CHART ...................................................................................12
7. TROUBLE SHOOTING................................................................................................................13
7-1.BEFORE SVC CHECKING ..................................................................................................13
7-2.QC TEST MODE..................................................................................................................13
7-3.HOW TO KNOW THE WATER LEVEL FREQUENCY.........................................................13
7-4.ERROR DISPLAY ................................................................................................................14
8. ERROR DIAGNOSIS AND CHECK LIST ....................................................................................16
8-1. DIAGNOSIS AND ANSWER FOR ABNORMAL OPERATION ...........................................16
8-2. FAULT DIAGNOSIS AND TROUBLE SHOOTING .............................................................19
9. DISASSEMBLY INSTRUCTIONS ...............................................................................................29
10. EXPLODED VIEW AND PARTS LIST .......................................................................................39
10-1. THE EXPLODED VIEW OF CABINET ASSEMBLY .........................................................39
10-2. THE EXPLODED VIEW OF CONTROL PANEL AND DISPENSER ASSEMBLY ............40
10-3. THE EXPLODED VIEW OF DRUM AND TUB ASSEMBLY .............................................41
10-4. THE EXPLODED VIEW OF DRYER ................................................................................42
2
1. SPECIFICATION
WD-1481RD/WD-14311RDA,
WD-14311(6)RD/WD-12311(6)RD/
WD-14312(7)RD/WD-12312(7)RD/
WD-14310(5)RD/WD-12310(5)RD/
AWD-14312(7)RD/AWD-12312(7)RD
ITEM
POWER SUPPLY
WD-1485RD
220V-240V~, 50Hz
PRODUCT WEIGHT
ELECTRICITY
CONSUMPTION
66kg
140W
SPIN
300W
FAN MOTOR
25W
DRAIN MOTOR
40W
2100W
2000W
DRY HEATER
1200W
1500W
1000W
WASH
REVOLUTION
SPEED
WD-10PFD, 10PFP
WD-14311RD
110V~, 60Hz
WASHING
WASH HEATER
WD-1488RD
45rpm
WD-1481RD/WD-14311RDA/WD-14311(6)RD/WD-14312(7)RD/
SPIN
WD-14310(5)RD/AWD-14312(7)RD/WD-10PFD/WD-10PFP/WD-1488RD
WD-12311(6)RD/WD-12312(7)RD/WD-12310(5)RD/AWD-12312(7)RD
OPERATION WATER PRESSURE
400/800/1000/1200 rpm
0.3-10kgf/cm (30-800kPa) 0.3-10kgf/cm2 (30-1000kPa)
2
0.3-10kgf/cm (30-1000kPa)
2
CONTROL TYPE
400/800/1000/1400 rpm
Electronic
WASH CAPACITY
8kg/8.5kg/10.1kg(Cotton)
10kg/10.1kg
DRY CAPACITY
4kg/4.2kg/10.1kg(Cotton)
6kg/10.1kg
DIMENSION
WASH PROGRAM
RINSE
600mm(W) 645mm(D) 850mm(H)
Cotton, Cotton-Eco, Synthetic, Delicate, Wool/Silk, Hand Wash, Quick 30, Duvet, Drain
Normal / Rinse+ / Rinse++ / Normal+Hold / Rinse++Hold
DOOR SWITCH TYPE
Bi-Metal type
WATER LEVEL
10 steps (by sensor)
RESERVATION
From 3 hours to 19 hours
SENSING OF THE LAUNDRY AMOUNT
Adapted
FUZZY LOGIC
Adapted
DISPLAY OF THE REMAINING TIME
Adapted
ERROR DIAGNOSIS
10 items
POWER AUTO OFF
Adapted
CHILD LOCK
Adapted
AUTO RESTART
Adapted
TIME SAVE
Adapted
3
2. FEATURES & TECHNICAL EXPLANATION
2-1.FEATURES
■ Automatic process from washing to drying.
Automatic process from washing to drying can be
selected easily.
Washing capacity : 8kg/8.5kg/10.1kg(Cotton)/10kg
Drying capacity : 4kg/4.2kg/10.1kg(Cotton)/6kg
■ More economical by Intelligent Wash System
Intelligent Wash System detects the amount of load and water
temperature, and then determines the optimum water level and
washing time to minimize energy and water consumption.
■ Direct Drive system
The advanced Brushless DC motor rotates the Drum directly
without belt and pulley.
■ Child-Lock
The Child-Lock system has been developed to prevent
children from pressing any button to change the program
during operation.
■ Low noise speed control system
By sensing the amount of load and balance, evenly distributes
load to minimize the spinning noise level.
■ Auto Restart
Although the washing machine is turned off by a power failure, it
restarts automatically in its stopped process when power is
supplied again. And it will be the same when the machine
unplugged in operation is plugged in again.
4
2-2.DETERMINE WASHING TIME BY FUZZY LOGIC
To get the best washing performance optimal time is determined by sensing of water temperature,
selected washing temperature and laundry amount.
water
temperature
washing time
selected
washing
temperature
FUZZY
LOGIC
rinsing time
the best
washing
performance
spin rhythm, time
laundry
amount
SENSING
PROCESSING
DETERMINATION
EFFECT
2-3.WATER LEVEL CONTROL
● This model adopts a pressure sensor which can sense the water level in the tub.
● Water supply is stopped when the water level to the preset level, then washing program proceeds.
● Spinning does not proceed until the water in the tub reduces to a certain level.
5
3. PARTS IDENTIFICATION
예
세 탁
울
합 섬
표 준
절전삶음
헹 굼
탈 수
약
헹굼물 추가
추가
남은 시간
이 불
불 림
애 벌
본세탁
소 량
급 속
수
5 (회)
4
3
2
1
1400
1000
800
600
400
(rpm
)
택
시간선
력
강
준
표
(절전)
다림질
온
저
시간단축
헹굼+탈
삶 음
약
건 조
예
헹굼물
란제리
세 탁
헹 굼
탈 수
탈 수
급 속
■ ACCESSORIES
Spanner
6
4. INSTALLATION
Before servicing ask troubles of customers
Check the adjustment(power supply is 220-240V~, remove the transit bolts....)
Check the troubles referring to the trouble shooting.
Decide service steps referring to disassembly instructions.
And then, service and repair.
After servicing, operate the appliance whether it works O·K or NOT.
■ STANDARD INSTALLATION
The appliance should be installed as follows.
REMOVE THE TRANSIT
BOLTS
INSTALL THE APPLIANCE
ADJUST THE
ON FLAT AND FIRM SURFACE
HORIZONTAL
• Remove the transit bolts
(4EA:①)with supplied spanner.
• Turn the leveling feet to
set the appliance horizontally.
• Keep the transit bolts and
spanner for future use.
• Insert the 4 caps
provided into the hole
2
1
• The appliance goes up by
rotating the feet clockwise.
• The appliance come down by
rotating the feet counter
clockwise.
7
■ HOW TO CONNECT INLET HOSE
• Check that the rubber packing is inside of the
valve connector.
• Connect the inlet hose firmly to prevent leak.
■ CONNECT DRAIN HOSE
· Make sure that the hose is not twisted.
· Avoid submerging the end of the hose.
※ The drain hose should be placed under 100cm from the floor.
■ CONNECT POWER PLUG
· Avoid connecting several electric devices,
It may be the cause of the fire.
· Connect the power plug to the wall outlet.
8
TEST OPERATION
Preparation for
washing.
Press the POWER button.
•Connect the power plug to
the outlet.
•Connect the inlet hose.
•In case of Coloreds program.
Check automatic reverse
turn.
Check the water supply.
MAX
Check the water heating.
Press the Start/Pause
button.
max
·Press the Temp. button
and the present temperature will
be displayed.
Check drain and spin
·Check if the drum rotates
clockwise and counterclockwise.
Power off and open the
door
·Check if water is supplied
through the detergent dispenser.
Water removal
·Turn off Wash and Rinse after
pressing the Start/Pause button
and start the machine again.
·Check drain and spin.
·Power off and then power on.
·Check if the door can be
opened after 3 minutes.
9
·If SVC is needed during
check, remove
the remaining water by pulling
out the hose cap.
5. OPERATION
• Use this button to turn the power
On/Off.
• This display shows:
a) the estimated time remaining in the
cycle when operating.
b) an error code when an error has been
detected.
• Use this option to pre
Press and hold PRE
lock/unlock control.
• When Child lock is se
buttons are disabled
can lock the washer w
• Rotate the Cycle selector
knob to select the cycle
designed for different
types of fabric and soil
levels.
• Use this button to Start/
Stop the washer.
• Pre Wash: Use this option for loads that need pretreatment. It add 16
minutes prewash and drain.
• Rinse+Spin: Use this option to rinse and then spin.
• Soak: Use this mode to wash normal clothes or think and heavy
clothes which are excessively dirty.
• Spin Only: When you want Spin only, select this option.
• Dry Only: When you want Dry only, select this option.
10
• TIME DELAY
event unwanted use of the washer.
WASH button for 3 seconds to
et, CHILD LOCK lights and all
except the Power
button. You
while it is operating.
• These lights show which portion
of the cycle the washer is
operating.
• Allows the start of any cycle
to be delayed for 3~19
hours.
• INTENSIVE
• If the laundry is heavily
soiled “Intenive” option is
effective.
• By selecting the Intensive
option, the wash time may
be extended, depending
on the program selected.
• To use this option press
the Intensive button once
before the wash program
is started.
• Rinse, Spin, Temp. Button
• DRY Button
• Select a water temperature based on the type
of load you are washing.
• Dry programs selected by pressing the Dry button.
• To change the spin speed, press the Spin
Speed button repeatedly to cycle through
available options.
• By pressing the button [Cupboard - Very - Time Low Temp.- Iron] can be selected.
• To change the soil level, press the Soil Level
button repeatedly until the desired setting is
on.
11
6. WIRING DIAGRAM / PROGRAM CHART
About 1:50
About 1:15
About 55
About 1:05
About 1:00
About 30
About 2:00
About 2:50
About 33
About 46
About 28
About 17
About 30
12
7. TROUBLE SHOOTING
7-1.BEFORE SVC CHECKING
■ Be careful of electric shock or disconnecting the parts while trouble shooting.
■ Voltage of each terminal in 220-240V~ and DC while applying an electric current.
7-2.QC TEST MODE.
① Pressing Rinse, and Spin button simultaneously.
② Press the Power
button, while the above condition.
③ Press the Start/Pause button as follows.
Number of times the
Start/Pause button is pressed
Check Point
Display Status
None
Turns on all lamps and locks the door.
1 time
Tumble clockwise.
rpm (40~50)
2 times
Low speed Spin.
rpm (600~650)
3 times
High speed Spin.
rpm (1300~1350)
4 times
Inlet valve for prewash turns on.
Water level frequency (25~65)
5 times
Inlet valve for main wash turns on.
Water level frequency (25~65)
6 times
Inlet valve for hot water turns on.
Water level frequency (25~65)
7 times
Inlet valve for dry water turns on.
Water level frequency (25~65)
8 times
Tumble counterclockwise.
rpm (40~50)
9 times
Heater turns on for 3 sec.
Water temperature
10 times
Circulation pump turns on.
Water level frequency (25~65)
11 times
Drain pump turns on.
Water level frequency (25~65)
12 times
Power off and unlock the door.
Turn off all lamps.
7-3.HOW TO KNOW THE WATER LEVEL FREQUENCY
✽ Press the Rinse and Spin button simultaneously.
The digits means water level frequency(10-1 kHz)
ex) 241 : Water level frequency = 241× 10-1 kHz
=24.1 kHz
7-4.HOW TO KNOW TO TEMPERATURE OF EACH THERMISTOR
AT OPERATING CONDITION.
■ Thermistor in tub : Press the [Temp.] button.
■ Thermistor in dry duct : Press the [Dry] button.
■ Thermistor in condensing duct : Press the [Intensive] and [Spin] button simultaneously.
13
7-5.ERROR DISPLAY.
• If you press the Start/Pause button in error condition, any error except ‘ ’ will disappear and the
machine will change into pause status.
• In case of『 』
,『 』
,『
』
, if the error is not resolved within 20 sec., and in case of other errors,
if the error is not resolved within 4 min., power will be turned off automatically and the error only will be
blinked. But in case of『 』
, power will not be turned off.
ERROR
SYMPTOM
CAUSE
1
WATER INLET
ERROR
• Not reached to the water level(246)within 8
minutes after water supplied or not reached to
the preset water level within 25 minutes.
2
DRAIN ERROR
• Not fully drained within 10 minutes.
3
OVERFLOW
ERROR
4
• Water is over flowing(over 8 level).
※ If
is displayed, drain pump operates to
drain water automatically.
SENSOR PRESSURE
S/W ERROR
• The sensor pressure switch is out of order.
5
DOOR OPEN
ERROR
• In case of operating the reservation function or
the other function with door opened. Close the
door, then the error display is resolved.
• The door switch is out of order.
6
IMBALANCE
ERROR
• The appliance is tilted.
• Laundry is gatherd to one side.
7
HEATING
ERROR
• The THERMISTOR is out of order.
14
ERROR
8
CURRENT
ERROR
SYMPTOM
CAUSE
• MAIN PWB ASSEMBLY is out of order
☞ Replace the MAIN PWB ASSEMBLY
• Winding in the STATOR ASSEMBLY is short-circuited.
☞ Replace the STATOR ASSEMBLY
•“
” is dispplayed during a high spin
☞ Replace the LEAD WIRE ASSEMBLY (MOTOR)
9
MOTOR
ERROR
• The connector in the LEAD WIRE ASSEMBLY is not connected to
the connnector of STATOR ASSEMBLY
☞ Reconnect or repair the connector
• The hall sensor is out of order/defective.
☞ Replace the STATOR ASSEMBLY
10
DRY
HEATOR
ERROR
• The Dry Heater is out of order
☞ Replace the Dry Heater
• The Connector of the Dry Heater is not connected properly to the
connector in the Main PWB ASSEMBLY
☞ Reconnect or repair the connector
• The Dry fan motor is out of order
☞ Replace the fan Motor.
15
8. ERROR DIAGNOSIS AND CHECK LIST
8-1.DIAGNOSIS AND ANSWER FOR ABNORMAL OPERATION
SYMPTOM
NO POWER
GUIDE FOR SERVICE CALL
Is the power plug connected firmly to
220-240V~ outlet?
Power failure? or Breaker opened?
Visit to check
Water inlet trouble
Is "
" displayed?
Is the tap opened?
Is the tap frozen?
Is the water supply shut-off?
Is filter in the inlet valve clogged with
foreign material?
Visit to check
16
Clean the filter of
inlet valve
GUIDE FOR SERVICE CALL
SYMPTOM
• Door does not open
• Error displayed on
the program
Started with door opened?
YES
Close the door
NO
Visit to check
Check if the door switch is O.K.
• DRAIN TROUBLE
Is "
" displayed?
YES
Is the debris filter clogged with foreign
material such as pin, coin and etc.?
NO
Is the drain hose frozen with water,
kinked or crushed?
NO
Visit to check
17
YES
Clean up
the filter.
SYMPTOM
。Suds overflow from the
appliance.
GUIDE FOR SERVICE CALL
Is low-sudsing detergent for the drum
washing machine used?
(In this condition, wash and
YES
spin do not operate
normally)
Is the proper amount of detergent used
as recommended?
YES
LOW-SUDSING
Recommend to reduce the using amount
of detergent.
This appliance has the automatic suds sensing function which
operates under much suds condition for good rinse and
preventing overflow.
When much suds are sensed, suds removing function such as
drain, water input and pause will operate without rotating the
drum.
。No effect of softener
Is softener put in the correct compartment of
the drawer?
YES
Is the drawer closed during wash?
YES
Is the softener cap clogged?
YES
Explain how to use softener
< Clean the compartment for softener >
Visit to check
18
8-2.FAULT DIAGNOSIS AND TROUBLE SHOOTING
CAUTION
1. Be careful of electric shock or disconnecting the parts while trouble shooting.
2. First of all, check the connection of each part terminal with wiring diagram.
3. If you replace the MAIN PWB ASSEMBLY, Put in the connectors correctly.
NO POWER
When measuring the voltage of the outlet,
is the voltage AC 220-240V~?
NO
Check the fuse?
YES
Is the led(1) on?
NO
Replace MAIN PWB
ASSEMBLY
YES
Reconnect the PWB
ASSEMBLY
YES
Reconnect the PWB
ASSEMBLY
<PWB ASSEMBLY (MAIN)>
YES
Is connector(2) disconnected or
disassembled?
<PWB ASSEMBLY (MAIN)>
NO
Is wire of the PWB ASSEMBLY disconnected?
NO
Replace PWB ASSEMBLY
19
NO WATER SUPPLY
Is water supply shut-off?
NO
NO
Open the tap.
When you press both Rinse button and Spin button
simultaneously, is the water level frequency below
240?
YES
Check the AIR CHAMBER
and the tube clogged
with impurity.
Is the inlet valve filter clogged with impurity?
YES
Clean the filter.
Is the tap opened?
YES
NO
NO
Is resistance between each terminal of INLET
VALVE ASSEMBLY is 2~8 kΩ?
NO
Replace the INLET VALVE
NO
Replace the MAIN PWB
ASSEMBLY.
YES
Check the voltage of the inlet valve connector
220-240V~.
ASSEMBLY
(Refer to 7-2 QC TEST MODE)
DETERGENT DOES NOT FLOW IN
Is water supplied?
NO
Refer to
「NO WATER SUPPLY」
NO
Check the wiring on the
dispenser.
YES
Are replaceptacles correctly connected to the
terminals of the INLET VALVE ASSEMBLY?
YES
Put the detergent in the
correct position
Is detergent put in the correct compartment of
the drawer?
NO
MAIN WASH
YES
: Detergent
YES
Is the detergent hardened?
20
PRE+MAIN
Clean the drawer.
SOFTENER DOES NOT FLOW IN
Is water supplied?
NO
Refer to
「NO WATER SUPPLY」
NO
Check the wiring on the
dispenser.
NO
Put it in the correct
compartment.
YES
Clean the cap and
drawer.
YES
Wiring diagram
Are receptacles correctly connected to the terminals
of the INLET VALVE ASSEMBLY?
YES
Is softener put in the correct compartment of the
drawer?
YES
Is the softener cap clogged?
ABNORMAL SOUND
Is the motor bolt loosened?
YES
Fix the bolt tightly.
NO
Is there friction noise from the motor?
21
YES
Replace the STATOR
ASSEMBLY or ROTOR
ASSEMBLY.
HEATING WITHOUT WATER
When pressing Wash and Rinse at the same time
after draining, is the water level frequency 248 ~ 262
or more?
When pressing Rinse, Spin buttons at the same
time while wash, is the water level frequency
between 230 - 243?
Replace the
S.PRESSURE SWITCH
ASSEMBLY
Checking voltage between two pins as press the
POWER button is the voltage 220-240V~?
Replace the MAIN PWB
ASSEMBLY
DRAIN MALFUNCTIONING
Is the drain hose twisted or frozen?
Repair the DRAIN HOSE
ASSEMBLY.
Is the impeller of the drain pump clogged?
Remove foreign material.
Is the connector disconnected, disassembled?
Reconnect or repair the
connector
Is the coil of the drain pump cut-off?
(resistance of coil is 80~150Ω)
Repair the DRAIN PUMP
ASSEMBLY.
When checking voltage between connectors
Repair the MAIN PWB
ASSEMBLY.
(①, ②)on spinning, is the voltage 220-240V~
as the figure?
22
AC 220-240V
HEATING CONTINUOUSLY ABOVE
THE SETTING WATER TEMPERATURE
When checking THERMISTOR on the tub is the
THERMISTOR loosened above 2mm from
the rubber?
23
Push the THERMISTOR
tightly to the rubber.
SPIN TROUBLE
Check on the spinning, is the frequency of the
water level 248 or more. The frequency can be
checked by pressing the Wash and Rinse buttons at
the same time on the program.
NO
YES
When pressing Rinse, Spin and POWER buttons at
the same time after power off, press the Start/Pause
button 1 times, is the drum low speed spin?
YES
Check the S.PRESSURE SWITCH
ASSEMBLY or HOSE (Pressure).
If the problem is on the
S.PRESSURE SWITCH
ASSEMBLY or the HOSE, replace
the S.PRESSURE SWITCH
ASSEMBLY or the HOSE.
Normal
NO
Is it disconnected, or disassembled?
[Red:3pin(1), GY:4pin(2)]
YES
Correct the connector.
NO
Check the motor connector, is the resistance of
the terminal same as the figure?
MOTOR TERMINAL (1)
NO
① ② ③
Replace the STATOR
ASSEMBLY
Resistance of terminal:
(1)
①~② / ②~③ / ③~① : About 5Ω~15Ω
YES
Replace the MAIN PWB ASSEMBLY
Does the spring of Latch Hook actuate?
Replace Door Assembly.
Is there clicking sound once or twice when the
START/PAUSE button is pressed to start the cycle?
Check the DOOR SWITCH
ASSEMBLY Connector and
MAIN PWB ASSEMBLY
(Red 3 pin, Yellow 4 pin and
white 3 pin connector (1)).
Is DOOR SWITCH ASSEMBLY broken?
24
Replace the DOOR
SWITCH ASSEMBLY.
[dHE] ERROR DISPLAY
Dry duct
~
NO
Replace the thermistor.
(6322FR2046B)
YES
Condensing
duct
CHECK FOR DRY HEATER TROUBLE
Thermistor
CHECK FOR DRY FAN MOTOR TROUBLE
Disassemble the cabinet cover and
condensing bellows.
Is there any foreign object in condensing
bellows.
NO
Disassemble the dry fan assy and dry duct
upper, and clean foreign object in duct and
fan.
25
YES
Clean the bellows
26
20~30
Black
Yellow
27
28
9. DISASSEMBLY INSTRUCTIONS
✽ Disassemble and repair the parts after pulling out power cord from the outlet.
CONTROL PANEL
① Unscrew the screws on the top plate.
PLATE ASSEMBLY(TOP)
② The plate assembly(Top) is pulled back and
then upward to arrow direction.
③ The cover(Inner) is disassembled.
① The PWB assembly(Display) connectors are
disconnected.
Hook
② Pull out drawer, three screws are unscrewed.
③ Push two upper hooks and pull the control
panel forward.
PANEL ASSEMBLY(CONTROL)
① The PWB assembly(Display) is disconnected.
② When 6 screws are unscrewed on the PWB
insulator and the PWB assembly(Display) is
disassembled from the PWB insulator.
PWB ASSEMBLY(DISPLAY)
29
PWB ASSEMBLY(MAIN)
① The back cover is removed.
② Two screws are unscrewed.
③ Disconnect connector from the wiring.
④ Pull the PWB assembly (Main) to arrow
direction.
DISPENSER ASSEMBLY
① The plate assembly(Top)and the
cover(lnner)are disassembled.
② Pull the drawer to arrow direction.
③ Two screws are unscrewed.
DRAWER
① The hose clamps and the hose are
disassembled.
② The ventilation bellows are disassembled on
the tub.
DISPENSER ASSEMBLY
30
INLET VALVE
① Disconnect the wiring connector.
② Remove the valve by two screws of the valve
holder.
2
1
When reconnecting the connector
4
3
VALVE ① (DRY)
YL/BK - BK
VALVE ② (PRE-WASH)
GY/WH - BK
VALVE ③ (NORMAL-WASH)
VALVE ®È (NORMAL-WASH)
VALVE ④ (HOT)
WH/BK - BK
BL/RD - BK
BL/RD - BK
DOOR
① Open the door completely.
② Remove the two screws from the hinge.
※ When removing the Door Assembly, it is
necessary to hold the Bracket that is inner of
the Cabinet Cover.
Removing method of remained water
Pull it out from hose.
※ First, prepare a bucket to put in the remained
water.
CAP (REMAINING HOSE)
31
GASKET ASSEMBLY
① The cabinet gasket clamp is released.
② Two screws are unscrewed from the cabinet
cover.
① Pull plat(-) screwdriver or pully knife into the
both sides of filter cover, and pull in out.
① Unscrew the screw from the lower side of the
cabinet cover.
① Unscrew the 2 screw from upper of the cabinet
cover.
32
① Disassemble the clamp assembly.
Tub Gasket
Clamp
① Remove dry gasket clamp by loosening the
screw.
① When reassembling the gasket, put the drain
hole of the gasket downward, then assemble.
Drain Hole
33
ROTOR ASSEMBLY, STATOR ASSEMBLY, FRICTION DAMPER
① Remove the back cover.
② After loosening the bolt, Rotor, pull out the
rotor.
Rotor
Bolt
(ROTOR ASSEMBLY)
① Remove the 6 bolt from the stator.
② Disconnect the 2 connectors.
HOW TO ASSEMBLE THE MOTOR
(STATOR ASSEMBLY)
① Remove the hinges (Damper) at the Tub.
② The Hinge(Damper) at the base is pulled off
pressing on the snaps at the sharp end.
③ The hinge at the base is pulled off.
Hinge
(Damper)
(To arrow direction)
Friction
Damper
(FRICTION DAMPER)
34
PUMP
① Remove pump outlet hose.
② Remove tub pump bellows.
③ Remove cap(Remaining Hose).
④ Disconnect the wiring.
⑤ Three screws are unscrewed from the cabinet.
⑥ Remove the pump to arrow direction.
HEATER
① Loosen the nut.
② Remove washing heater by pulling out.
Washing
Heater
Nut
Ring Terminal
CAUTION
When assembling the washing heater, insert
the heater to heater clip on the bottom of tub.
THERMISTOR
① Pull it out by holding the thermistor bracket.
If holding the wire and pulling out it, it may be
broken.
35
SWITCH ASSY, DOOR LOCK
① The cabinet cover clamp is removed and the
gasket is released.
② Two screws are unscrewed.
③ The door lock S/W is disconnected form the
wiring connector and the strap.
WHEN FOREIGN OBJECT STUCK BETWEEN DRUM AND TUB
① Remove washing heater.
② Remove the foreign object(wire,coin,etc) by
inserting long bar in the hole.
36
DRY DUCT
① Remove 6 screws and dry fan assembly.
Dry fan
Ass'y
Dry Duct
Upper
② Remove 7 screws and dry duct upper.
① Remove 2 screws and dry heater.
Thermostat
② Remove thermostat.
Dry Heater
CONDENSING DUCT
① Remove 17 screws from Dry duct upper and
Dry fan Assembly.
① Remove 5 screws and condensing duct.
37
10. EXPLODED VIEW AND PART LIST
10-1.THE PART LIST OF CABINET ASSEMBLY
A154
A153
A110
A140
A152
A151
A101
A102
A120
A150
A104
A103
A141
A100
A131
A485
A130
A430
A440
A134
A133
A450
A410
A303
A310
A200
A300
A275
A201
A240
A276
A220
A274
A272
A270
38
10-2 THE EXPLODED VIEW OF CONTROL PANEL &
DISPENSER ASSEMBLY
F436
F300
F462
F324
F322
F321
F170
F320
F160
F466
F432
F430
F225
F441
F220
F120
F215
F110
F210
F130
39
10-3 THE EXPLODED VIEW OF DRUM & TUB ASSEMBLY
K143
K360
K350
K123
K351
F140
K411
K121
K410
F465
F310
K122
K125
F464
F463
K146
K320
K111
M105
K310
K110
K141
K311
K140
K105
K115
K410
K130
K135
K610
K512
K510
K560
K611
K530
K131
F145
K340
F467
F468
K520
K550
F461
K344
K342
K346
40
K540
10-4 THE EXPLODED VIEW OF DRYER
M100
M240
M130
M111
M120
M110
M216
M210
M230
M215
M101
M220
41