Care, Use and Installation Booklet
FRONT-LOADING WASHER
Contents
Warnings and Safety Instructions, 2
Important Safety Instructions
Washer Description, 3
The front, the back
Control panel
Start and Programs, 4-6
Choosing a Program
Table of control panel lights
Table of preset wash programs
Table of washing options
Dispenser, 7
AW122
Automatic dispenser drawer
Dispenser compartments
About using bleach
Table of laundry aids
Maintenance and Care, 8-9
When to switch off electricity and water faucets
After washing is complete
Clean the exterior, interior & dispenser drawer
Clear the coin trap
Check the rubber inlet hoses yearly
Winterization
Troubleshooting, 10-11
Spare parts
Technical Details, 12
Recessed, closet, alcove installations
Installation Requirements, 13-15
Tools and Parts
Location
Water Inlet Requirements
Drain System Requirements
Electrical Requirements
Installation Instructions, 16-17-18
Remove Transit Screws/Spacers
Connect the Inlet Hoses
Route and Secure the Drain Hose
Level the Washer
Final Installation Checklist
1
Warnings and Safety Instructions
The machine was designed and built in compliance with the appliance international safety regulations.
The information on this page is provided for your safety and should be read carefully.
WARNING!
To reduce the risk of fire, electrical shock, or injury to persons when using your appliance,
follow basic precautions including the following:
! WARNING
10.
ELECTRICAL SHOCK HAZARD
Plug washer-dryer into a
grounded 3 prong outlet.
Do not remove ground prong.
Do not use adapter.
Do not use an extension cord.
Failure to follow these
instructions can result in death,
fire, or electrical shock.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Read all instructions before using the appliance.
Do not wash articles that have been previously
cleaned in, washed in, or spotted with gasoline, dry
cleaning solvents, other flammable or explosive
substances as they emit vapors that could ignite or
explode.
Do not allow children to play on or in the appliance.
Close supervision of children is necessary when the
appliance is used near children.
Before the appliance is removed from service or discarded, remove the door.
Do not reach into the appliance if the tub or drum is
moving.
Do not install or store this appliance where it will be
exposed to the weather.
Do not tamper with controls.
Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended
in the user-maintenance instructions or in published
user-repair instructions that you understand or have
the skills to carry out.
Do not add gasoline, dry-cleaning solvents, or other
flammable or explosive substances to the wash water.
These substances give off vapors, that could ignite or
explode.
11.
12.
13.
! WARNING
EXCESSIVE WEIGHT HAZARD
Use two or more people to move
and install the washer-dryer.
Failure to do so can result in back
or other injury
14.
15.
16.
17.
18.
19.
20.
21.
! WARNING
ELECTRICAL SHOCK HAZARD
Disconnect power before servicing.
22.
23.
Replace all panels before operating.
Failure to do so can result in death
or electrical shock.
2
Under certain conditions, Hydrogen gas may be produced in a hot water system that has not been used
for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE.
If the hot water system has not been used for such a
period, before using a washing machine, turn on all
hot water faucets and let the water flow from each
for several minutes. This will release any accumulated
Hydrogen.
Check the Coin Trap every few months to remove
coins, buttons or similar size objects.
This appliance must be properly grounded (see
Grounding Instructions).
Clothes, cleaning rags, mop heads and the like which
have traces of any flammable substances, such as veg-
24.
etable oil, petroleum based oils or distillates, etc. must
not be placed in the washing machine. These items
may contain flammable substances after laundering
which may smoke or catch fire by itself.
Always be sure to unplug the washing machine from
the electrical supply before attempting any service.
Do not insert/pull out the mains plug with wet hands.
Do not pull out the mains plug by tugging the cable.
Do not use an extension cord or an adapter to connect
the washing machine to the electrical power supply.
Caution when draining hot water.
The washing machine must only be used for it’s intended purpose.
Make sure drum is empty before loading washer.
Make sure that all water connections to the washing machine have shut-off valve(s) and that they are
readily accessible. Close the washing machine shut-off
valves at the end of each wash day.
Check the fill hose connections on a regular basis to
assure that they are tight and not leaking.
Do not machine wash fiberglass materials. Small particles can stick to fabrics washed in following loads and
cause skin irritation.
Check the inlet hoses periodically for bulges, kinks,
cuts, wear or leaks and replace them every five years.
SAVE THESE INSTRUCTIONS
Washer Description
Dispenser drawer
Control panel
Hot and cold
water inlet
Model No.
Power cord
Transit
bolts
Serial No.
Drain hose
Coin Trap
Extra Rinse
Program key
(Pull on Grey Tab)
Programs dial
Easy Iron
Soaking
ON-OFF
PreWash
D
O
Dispenser drawer
Knobs are hidden. To extract them, gently
press the middle of each knob.
Spin Speed
D = Door Lock Light
O = ON-OFF Light
Wash Temperature
Introduction
Congratulations on the purchase of your new Ariston washing machine. It is a highly sophisticated engineered
product that will give you many years of satisfaction. Please read this Owners Manual. It will show you ways to best
utilize your valuable purchase.
3
Start and Programs
Choosing a program
SPIN SPEED knob.
• To further customize the program, press
one of the four WASH OPTIONS buttons
(see Washing Options).
1. Plug the washer into the electrical socket.
2. Sort your laundry according to similar colors,
fabrics and degree of soil. For best results,
do not load more than the maximum capacity:
Fabric
Cottons
Synthetics
Delicate Fabrics
Wools
Bathrobes
3.
6. Open the dispenser drawer and add laundry aids
(see Dispenser drawer).
Maximum Load
12 lbs.
6 lbs.
5 lbs.
3 lbs.
5 lbs.
Note: If your previous washing machine was a
top-loader, initial loads may require little to no
detergent. Old detergent trapped in the clothes
will be released during the tumble action.
Open the door. Load the machine and make sure
the items are not in the way of the door seal.
7. Close the dispenser drawer.
4.
Close the door.
8. Press the ON-OFF button (in) to begin.
During the washing program, you cannot open
the door.
5.
Choose the wash program by checking the
Programs table (see Preset Washing Programs)
as well as the fabric care tags found on your
clothing.
9. When the cycle is complete, wait for the DOOR
LOCK Light to extinguish. Open the door and
take your laundry out.
• Select a washing cycle by rotating the
PROGRAMS dial clockwise.
• Set the wash water temperature with the
• TEMPERATURE knob.
• Set the high spin speed with the
10. Unplug the washer.
Lights
Light
What it means...
Note
•
DOOR LOCK
ON-OFF
4
Indicates when the
door is locked
Indicates the status
of the washer
•
•
Light ON = Locked
Light OFF = Unlocked
!
•
•
Slow Flash = Ready; awaiting
instructions
Solid Light = Program
accepted; in operation
Quick Flash = Program
competed, but door still
locked
•
•
•
The door will stay locked for
up to 2 minutes after the
program is completed
NEVER attempt to open the
door when the DOOR LOCK
light is ON
This washer can perform selfdiagnostics in the event of a
problem. If needed, this light
will indicate a fault code by
displaying a specific series of
blinking lights.
Start and Programs
Preset washing programs
Program
Clothing Type
COTTON
1 Sanitary
2 Heavy
3 Regular
4 Light
Description
•
120 minutes
•
Heating element
is used to reach
158ºF wash temp.
Colorfast Items
High Spin
Recommendation
•
1200 rpm
•
Eliminates harmful
bacteria and safely deep
cleans stained, cotton
colorfast items
The heating element will
take about 10 minutes to
reach full heat.
•
Bleach option not
available
•
90 minutes
1200 rpm
•
Sheets, tablecloths, etc.
Heavily soiled
whites and colorfast •
colors
50 minutes
1200 rpm
•
•
Jeans, towels, etc.
Fasten all hooks, zippers
and buttons
40 minutes
1200 rpm
•
•
Shirts, sweatshirts, etc.
Turn printed shirts inside
out before washing
Tie all strings before
loading
Exceptionally soiled
whites
Slightly soiled
whites and delicate
colors
•
•
PERMANENT PRESS
Heavily soiled
colorfast synthetics
•
80 minutes
800 rpm
•
Baby linen, etc.
6 Regular
Delicate color
synthetics
•
65 minutes
800 rpm
•
All types of slightly soiled
synthetics
7 Light
Delicate color
synthetics
•
40 minutes
800 rpm
•
All types of slightly soiled
synthetics
•
•
All types of delicate items
Place underwear, tights
stockings and other
delicates in a linen bag
5 Heavy
HAND WASHABLES
8 Light
9 Silk
10 Wool
Delicate items
•
64 minutes
600 rpm
Particularly delicate
items
•
60 minutes
No Spin
•
Curtains, silk, viscose
Wool
hand washables
•
65 minutes
600 rpm
•
•
•
•
Wool scarf, sweater, etc.
Turn knit items inside out
Use very little detergent
3 lb. max load
Please Note: cycle times will vary according to size and fabric type of load, water system temperature and room temperature
• DO NOT wash torn, frayed or non-hemmed items
• Empty all pockets before loading the laundry
Symbols Key
Stop/Reset
Spin Cycles
Easy Iron
(10 - 13 min.)
(Anticrease Stop)
Drain Only
(No Spin)
Fabric Softener
Only Cycle
Rinse Cycles
(25 min.)
5
Start and Programs
Washing Options
Option
KNOBS
TEMPERATURE
SPIN SPEED
BUTTONS
Soaking
Extra Rinse
Easy Iron
Pre-Wash
What it does...
Changes the preset wash water
temperature of the selected
program
Changes/excludes the preset
spin cycle of the selected
program
Rotate SPIN SPEED knob
to the desired speed
Adds a one hour soak to the
selected washing program
Press
SOAKING button (in)
Adds one extra rinse to the
selected Cotton Heavy Duty or
Permanent Press program
Automatically stops the selected
Permanent Press or Hand
Washables program before
the spin cycle begins. Laundry
soaks in water until the Easy
Iron button is pressed again.
•
Rinse water is always
COLD
•
•
Select
for No Spin
Faster spinning will
extract more water
from highly absorbent
fabrics
•
During soaking, laundry is gently tumbled
•
Recommended for
very large loads, when
too much detergent is
used or for detergent
contact allergies.
•
Prevents wrinkles
caused when laundry is
not removed promptly
from the drum.
Use this option when
you know you won’t
be able to remove the
laundry until long after
the cycle is finished.
Press
EXTRA RINSE button (in)
Press
EASY IRON button (in)
Program will stop when it
reaches the symbol on
the Programs dial.
•
To resume the program,
Press EASY IRON button
again (out)
•
Press
PRE-WASH button (in)
Delay’s the start of the
washing program by 1, 3, 9 or 12
hours so laundry is ready when
you are.
1. Rotate PROGRAMS dial
clockwise and select 1h, •
3h, 9h, or 12h.
2. Press ON-OFF button (in).
3. Wait 5 seconds for the
ON-OFF light to stop
flashing.
4. Rotate the PROGRAMS
dial clockwise and select
a washing program.
Stop/Reset Cancels/Interrupts the
selected program
6
Note
Adds an extra wash to the
selected program
(Not available in “Wool” cycle)
On PROGRAMS Dial
DELAY TIMER
How to set it...
Rotate TEMPERATURE
knob to the desired wash
temperature
1. Rotate the PROGRAMS
dial clockwise to a
Stop/Reset position.
2. Wait 5 seconds.
3. Rotate the PROGRAMS
knob to the desired
washing program or
Drain (see right).
•
Recommended for
heavily soiled loads
like work clothes or
children’s clothes.
The On-Off lamp will
flash (1 second on, 4
seconds off) to indicate
a Delay Start has been
set. The door can be
opened or closed at
any time before the
cycle begins.
To cancel a program
completely, select
(Drain). After the
washer drains, wait for
the DOOR LOCK light
to extinguish before
attempting to open the
door.
Dispenser Drawer
HE Laundry Powder
Automatic Dispenser Drawer
Once loaded in the proper compartment(s) in the dispenser drawer, Detergent, Fabric Softener and Bleach
will automatically be added at the appropriate time
during the washing program.
For best results, use HE (High
Efficiency) detergent. HE laundry
detergents dissolve more quickly
in less water and won’t overfoam in
front loading washers.
Splendide All-Natural
Premium Laundry Powder
(Part No. 1005)
About Using Bleach (Compartment 4)
•
•
•
•
Dispenser Compartments (above)
1.
2.
3.
4.
Detergent for Pre-Washing (powder only)
Detergent for Washing (powder or liquid)
Liquid Fabric Softener
Liquid Bleach
Laundry Aid
Amount
COMPARTMENTS 1, 2
1 to 2
Powder Detergent Tablespoon(s)
COMPARTMENT 2
Liquid Detergent
Liquid Fabric
Softener
½ to 1
Tablespoon
•
•
Special Note
•
Powder detergent is
recommended.
Detergent Facts
•
•
If using liquid detergent,
ALWAYS add detergent to
compartment no more than a
few seconds before the start of
the wash cycle.
•
Using a liquid fabric softener (or
a detergent with a built-in soft- •
ener) fluffs clothes. This helps
speed drying times and reduce
wrinkles.
Fabric perfumes can be used in
•
this compartment.
Using more than the recommended amount of fabric softener
can impair wash results.
¼ to ½
Tablespoon
COMPARTMENT 3
•
Bleach can only be used when HOT is selected on
the TEMPERATURE knob
If bleaching is necessary, the Bleach Compartment 4 (provided) must be inserted into compartment 1.
Always dilute bleach before using.
If used, you will see water in the Bleach compartment after the washing program is complete. This
is normal.
Bleach cannot be used during the “Silk” washing
program.
Using the Bleach compartment excludes the
possibility of using the
PreWash cycle.
DO NOT exceed the Max
level (shown above). If you
overfill the bleach dispenser,
bleach will run directly into
the machine and may possibly
damage clothes.
Bleach “Max” level
•
•
Never use too much detergent
or additives. Using too much will
cause excessive sudsing, and
scaling which may reduce performance and cause possible damage
to your washer.
NEVER use detergent for “hand
washing” or a detergent that is
not designated for “machine use.”
When washing in COLD water,
reduce amount of detergent
7
Maintenance and Care
When you should switch off the
electricity and turn off the water faucets
Clear the coin trap
Unplug the washer and turn off the water faucets when
not using it, when cleaning it and during maintenance
activities.
This washer contains a self-cleaning pump that does
not require any cleaning or maintenance. However,
small objects (like coins, hair clips, keys, etc.) may accidentally fall into the pump. To avoid possible damage,
they are withheld in an accessible coin trap, located at
the bottom, right corner of the washer.
After washing is complete, always
If needed, follow these instructions to remove items
that may have accidentally been washed and got
caught in the coin trap:
•
1.
•
Turn off the water faucets to relieve pressure on
the inlet hoses.
Wipe the inside of washer door with a soft cloth.
Clean the Exterior
As needed, clean the exterior with a rag dipped in lukewarm water and soap. Never use polish of any kind.
2.
3.
Clean the Interior
In hard water areas or where heavily soiled items are
frequently washed, you may periodically need to
remove body oils or detergent that has accumulated
in the drum. To remove this build-up, run the washer
through a complete cycle using HOT water and 2 cups
of a non-precipitating water softener.
Periodically, apply a thin coat of paste wax to the inner
door (especially the area that is immediately next to the
door window) to protect it from laundry aid spills and
discoloration.
Clean the Dispenser Drawer
As needed, rinse
buildup of detergent
or other laundry aids
from the dispenser
drawer. To remove the
dispenser drawer, pull
it outwards, as indicated in the picture. Then
leave it under warm
running water for a
few minutes.
8
4.
5.
With the washer OFF and
empty, gently ease down
the top of the kick-plate
panel (right) with a flat
blade screwdriver or
plastic putty knife.
Remove the panel by
lifting slightly and pulling
forward.
Place a small pan or towel
under the pump to catch
any water still left in the
pump.
Turn the large knob counterclockwise and then
pull the filter straight out.
When finished cleaning, reinstall the filter and
ensure that it’s securely tightened. Finally, re-fit the
kick-plate panel.
Check the Rubber Inlet Hoses Yearly
Inspect the inlet hoses yearly. If you see any cracks,
bulges or other signs of wear replace the hose immediately. Record the hose installation/replacement dates
on hoses for future reference.
IMPORTANT!
Always replace the inlet hoses after 5 years
of use.
Maintenance and Care
Winterization (for RV or marine installs)
A) To winterize your washer-dryer
1) With machine power OFF, pour ½ quart of RVtype antifreeze into washer drum
2) Close door. Advance Program Dial to a
position
‘Spin’
3) Press ON-OFF Button (IN). Wait 1-2 minutes
4) Press ON-OFF Button (OUT). Unplug washer-dryer
from electrical outlet (or disconnect power)
5) Turn water supply faucets OFF. Disconnect inlet
hoses from faucets. Drain remaining water from
the hoses. FINISHED.
Optional RV Winterization - If currently pumping antifreeze
through a fresh water system
1) With machine power OFF, turn WASH TEMP knob
to HOT
B) To use again, flush water pipes, then
1) Reconnect water inlet hoses to corresponding
HOT/COLD faucets. Turn faucets ON. NOTE: Check
water inlet hoses and pump periodically (see Users Guide).
2) Plug washer-dryer in to appropriate electrical outlet (see Users Guide) - or reconnect power supply
3) With ON-OFF button in the OFF (OUT) position,
pour ½ TBSP. of powder detergent (or liquid
equiv.) into the ‘Detergent’ compartment inside
the Dispenser Drawer (see Users Guide).
4) Advance Program Dial to cycle 4
5) Press ON-OFF button (IN). Allow machine to run
through complete cycle to clean out any remaining antifreeze. FINISHED.
2) Advance Program Dial to cycle 3
3) Press ON-OFF button (IN). Let machine fill until
antifreeze is in the drum
4) Advance Program Dial to
seconds
‘RESET’. Wait 5
5) Advance Program Dial to a
‘Spin’ position. Let
the antifreeze drain from the drum
6) Advance Program Dial to
seconds.
‘RESET’. Wait 5
7) Press the ON-OFF button (OUT)
8) Turn WASH TEMP knob to COLD
9) Repeat steps 2 through 7. FINISHED.
9
Troubleshooting
Before you call our Customer Care Department, go through the following troubleshooting suggestions
Problem:
The washer
won’t start.
The washer won’t fill.
Possible Causes / Solutions:
•
•
•
•
•
•
•
The plug is not plugged into the socket, or not making contact.
There has been a power outage.
The fuse has blown.
The door is not closed securely.
The ON-OFF button is not pressed (in)
The Programs dial has not been set correctly (see Preset Washing Programs)
The water supply faucets are not turned on
•
•
The hose is not correctly connected to the tap.
The inlet hose filter screens need to be cleaned. If work has recently been
carried out on the water piping, or if water is very hard, the filters could be
clogged with particles or debris.
The rubber hoses are kinked or squashed.
•
The Programs dial
keeps turning.
The washer is
continuously filling
and draining with
water.
•
Wait for the washer to drain, then Stop/Reset the washer (see Washing
Options). Set another program. If the knob continues to turn, contact our
Customer Care Department.
•
The drain hose is positioned too low. It must be installed at a height ranging
from 25” to 34”.
The end of the drain hose is under water.
The wall drainage system does not have a breather pipe.
There may be a problem with your drain trap if the washer is installed on an
upper floor of a building.
•
•
•
The washer
does not drain or spin.
•
•
•
•
The Easy Iron function is selected (see Washing Options)
The Coin Trap is clogged (see Clear the Coin Trap)
The drain hose is kinked or squashed.
The drain hose is clogged or positioned incorrectly so it is blocking water flow.
The washer vibrates
excessively during
the spin cycle.
•
•
The shipping bolts and spacers have not been removed.
The washer is not leveled correctly.
•
The inlet hoses are not secured properly. They should be tightened by hand but
not forced.
The detergent dispenser needs to be cleaned (see Clean the Detergent Dispenser)
The drain hose is not secured properly.
The washer leaks.
There is too
much foam.
•
•
•
•
•
Improper detergent for this washer (see Dispenser Drawer)
Too much detergent has been used (see Dispenser Drawer)
To clear excess suds, set the Programs dial to “Rinse” and allow the machine to
rinse out.
If you still have a problem, call Westland Sales: 1-800-356-0766
Please have the following info ready when you call:
1) Nature of the malfunction
2) Model no. (AW122NA)
3) Serial number (i.e. S/N...)
10
Spare Parts
This washer is a complex machine. Repairing it yourself or having a non-authorized person try to repair it could cause
harm to one or more persons and to the machine, and could invalidate the warranty.
Always call Westland Sales first if you experience any problems with this machine.
Contact number: 1-800-356-0766 or 503-656-2280.
11
Technical Details
Recessed, closet and alcove
installation (Instructions)
Technical Details
Model
AW122
Dimensions
23 ½”
32 ¾” *
22 1/2”
* With legs screwed all
the way in
(59.5 cm) wide
(85 cm)
high
(53 cm)
deep
Capacity
2 to 12 lbs (7 kg)
Electric
Connections
120 V 60 Hz (min. working 108V)
max. absorbed power: 1350 W, 12 A.
Water
Connections
max. pressure:
min. pressure:
Spin Speed
up to 1200 rpm
C
UL
®
US LISTED
100 psi (689.6 kPa)
20 psi (137.9 kPa)
The machine may be installed in a
recessed area, closet or alcove.
The installation spacing is in inches and is the
minimum acceptable. Additional spacing should
be considered for easy installation, servicing and
compliance with local codes or ordinances. Other
installations must use the minimum dimensions
indicated.
Additional clearances for wall, door and floor
moldings may be required.
Minumum Clearances
This appliance was tested by UL
and conforms with both Canadian
and U.S. UL safety requirements and
displays their Mark
Indesit Company offers their
customers products with the Energy
Star label
As a result of technological progress, the manufacturer reserves the right
to make any improvements to its appliances without giving prior notice
to its clientele.
Sides
0”
Front/Back
1”
Front View
0 in.
(0 cm)
33-1/4 in.
(84.5 cm)
23-1/2 in.
(59.7 cm)
0 in.
(0 cm)
0 in.
(0 cm)
Side View
18-1/4 to
24 1/4 in.*
(46.4 to 61.6 cm)
1 in.
1 in.
(2.54 cm)
(2.54 cm)
*Depth dimension varies with model.
12
Installation Requirements
Tools and Parts
Assemble the necessary tools and supplies before
beginning the washer installation. The parts supplied
are in the drum.
Tools needed for installation:
10mm Wrench, Screwdriver
Parts Supplied
U-Clamp
Transit Bolt Hole Plugs (4)
If You Have
No access to Hot/Cold
water hookups
Water damage
Concerns
Floor drain
Disposer drain
Shifting Concerns
(RV and Marine
Installations)
You’ll Need to Buy
Splendide Faucet Adapter kit,
Part No.154187104A (8ft , 2.4m)
Splendide Drain-A-Way™ Pan,
Part No. PI-22, PI-24 (or similar)
Siphon break kit (sold at most
hardware stores)
“Y” connector (sold at most
hardware stores)
Splendide SecureFit™
installation Brackets, Part No.
MK01. Keeps washer in place during travel to prevent:
•
•
•
•
•
•
Kinked inlet hoses
Disconnected dryer vent
hoses
Crushed dryer vent hose
Blocked dispenser drawer
Knobs rubbing against closed
doors
Scuffed cabinet woodwork
All Splendide parts are available
direct from Westland Sales: 1-800-356-0766
Location
Selecting the proper location for the washer-dryer
improves performance and minimizes noise. Proper
installation is your responsibility. The washer-dryer
can be installed under a counter, in a closet, in an
alcove, or in a recessed area with minimum installation
clearances of 0” sides, 1” front/back.
You’ll Need
• A water heater set to deliver 120°F (49°C) water to
the washer.
• A grounded electrical outlet located within 6 ft.
(1.8m) of where the power cord is attached to the
back of the washer. (See “Electrical Requirements.”)
Make sure the electrical socket is accessible so you
can unplug the washer when not in use.
• Hot and cold water faucets located within 8ft. (2.4
m) of the hot and cold water fill valves, and water
pressure of 7.5-100 psi.
• A solid, level floor that can support at least 280
lbs. (127 kg). DO NOT install on carpet. The machine must rest solid on a sturdy floor for optimum
performance and minimum vibration.
• Enough space to open the door fully so you can load
and unload easily.
• RV/Marine Installations: When locating the appliance in a towable trailer or watercraft, position the
machine over the axles or mid-ship where movement is at a minimum. Block the machine to prevent
extreme movement or tipping.
Water Inlet Requirements
Water pressure must range within 7.5 and 100 psi. If
the water pipes are new or left unused, before connecting the machine, run the water until clear to
remove debris. Connect the inlet hose to a cold water
tap having a 3/4” BSP thread. Ensure that there are
rubber washers at the end of each inlet hose. The
L-Shaped end goes on the machine and the straight
ends on the water faucets.
CAUTION!
1. This washing machine must only be
operated with cold and hot tap water. Do
not connect the appliance to a mixer tap of
an unpressured hot-water boiler.
2. To prevent water damage, the hot and cold
water valves should be accessible when
the washer is in place and should always be
turned off when the washer is not in use.
13
Installation Requirements
Drain System Requirements
The washer-dryer can be installed using the standpipe
drain system, floor drain system or the sink drain system.
To prevent siphoning, the outlet end of the drain hose
(provided with unit) MUST be at least 20” (50.8 cm) above
the base of the machine. Not more than 6” (15.24 cm) of
the drain hose should be inserted into the drain pipe.
Sink Drain W/ "Y" Branch Tailpiece
Laundry Sink Drain
25" (62 cm) min.
with an air break
Floor Standpipe
Wall Standpipe
Cable tie
"Y" Tail Piece
B
This connection MUST be
before drain trap and at
least 20" (50.8 cm) above
the floor where washer will
be installed.
20" (51.8 cm) min.
34" (86 cm) max.
Standpipe
A
A & B = 25" (62 cm) min. / 34" (86 cm) max.
Floor Standpipe w/ "Y" Branch Tail Piece
The standpipe drain requires a minimum diameter standpipe of 1-1/4” (3.2 cm). The minimum carry-away capacity
can be no less than 7 gal (26.5 L) per minute. The top of
the standpipe must be at least 25 in. (62 cm) high and no
higher than 34” (86 cm) from the bottom of the washer.
Optional
Splendide Faucet Adapter
Kit, Part No. 154187104A
• Supplies water from the
faucet and discharges water
directly into the sink.
• Designed for installations
where washer-dryer hookups
are not available.
U-Clamp
6" max.
Standpipe
25" (62 cm) min.
34" (86 cm) max.
20" (50 cm) min.
with an air break
The floor drain system requires a siphon break that may
be purchased separately.
The sink drain system connected to a garbage disposer
requires a “Y” connector (sold separately).
14
Splendide Drain-A-Way™
Pan, Part No. PI-24, PI-22
• Durable, rotomolded pan
with seamless construction
and reinforced corners.
• Fits under the washer.
• Designed to protect against
water damage in the event
of overflow or flooding.
Fig. 7
Faucet Adapter Kit, Part No.
154187104A
Drain-A-Way Pan, Part No.
PI-22
Installation Requirements
Electrical Requirements
GROUNDING INSTRUCTIONS
Electrical Shock Hazard
(Death, Fire, or Electric Shock)
This appliance must be grounded.
This appliance should be connected to an
Individual Branch Circuit with N.14 AWG Wire
and Protected by 15A fuse
In the event of a malfunction, or breakdown,
grounding will reduce the risk of electric shock
by providing a path of least resistance for
electric current. This appliance is equipped
with a cord having an equipment grounding
conductor and grounding plug. The plug must
be plugged into an appropriate outlet that is
properly installed and grounded in accordance
with all local codes and ordinances. DO NOT
modify the plug provided with the appliance.
If it will not fit the outlet, have the proper outlet installed by a qualified electrician.
WARNING: Improper connection of the
equipment-grounding conductor can result
in a risk of electric shock. Check with a
qualified electrician or serviceman if you
are in doubt as to whether the appliance is
properly grounded.
! WARNING
ELECTRICAL SHOCK HAZARD
Plug washer-dryer into a
grounded 3 prong outlet.
Do not remove ground prong.
Do not use adapter.
Do not use an extension cord.
Failure to follow these
instructions can result in death,
fire, or electrical shock.
• A 120-volt, 60-Hz., AC-only, 15 or 20-amp, fused electrical
supply is required. Time-delay fuse or circuit breaker is
recommended. It is recommended that a separate circuit
serving only this appliance be provided.
• This washer-dryer is equipped with a 6’ power supply
cord having a 3-prong ground plug.
• To minimize possible shock hazard, the cord must be
plugged into a properly grounded (3) prong electrical
outlet capable of 120 Volt, 60 Hz and grounded in accordance with local codes and ordinances. If a mating
outlet is not available, it is the personal responsibility
and obligation of the customer to have the properly
grounded outlet installed by a qualified electrician. The
outlet shouldn’t be controlled by a wall switch or pull
cord which can be turned off accidentally.
• If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that
the ground path is adequate.
• Do not ground to a plastic plumbing lines, gas lines or
water pipes.
• Check with a qualified electrician if you are not sure the
washer is properly grounded.
• DO NOT use an extension cord.
• DO NOT have a fuse in the neutral or ground circuit.
• DO NOT install or store this appliance where it will be
exposed to weather or in an area where gasoline or other
flammables are stored.
15
Installation Instructions
! WARNING
EXCESSIVE WEIGHT HAZARD
Use two or more people to move
and install the washer-dryer.
Failure to do so can result in back
or other injury
Route the Drain Hose
Proper routing of the drain hose protects your floors from
damage due to water leakage. Carefully read and follow
these instructions.
The drain hose is connected to the washer. To prevent
drain water from going back into the washer:
• Do not straighten the drain hose, and do not force
excess drain hose into the standpipe. Hose should be
secure, but loose enough to provide a gap for air.
• When routing the drain hose through cabinets or walls,
use a protective material such as electrical tape to cover
sharp edges that could damage the hose.
Remove the Transit Screws/Spacers
First, position the washer so that the rear of the unit is
within approximately 3 feet (90 cm) of the final location.
There are 4 bolts in the rear panel of the washer that support the suspension system during transportation.
1. Using a wrench, loosen each of the bolts.
Drain Hose
2. Once loosened, pull out the bolt, including the rubber
grommet and the plastic spacer covering the bolt.
3. Once all 4 bolts are removed,
close the holes with the transit
bolt hole plugs (provided).
4. Keep the bolts, rubber
grommets and plastic spacers in
a safe place. These items should
be reinstalled if the machine is
transported in the future.
Connect the Inlet Hoses
Before connecting any hoses, run the faucets until the
water is clear to remove any debris. Make sure the drum is
empty. Please use the new hoses supplied. Old hoses may
cause leaks due to worn out washers or may be split due to
water pressure.
1. Connect the angled ends of the hoses to the inlet
valves at the back of the machine (20mm threads).
Screw on the couplings BY HAND until they are seated
on each gasket.
IMPORTANT!
Transit Screws/Spacers must be removed
before use.
16
Installation Instructions
2. Attach the hose connected to the ‘H’ valve to the hot
water faucet. Screw on the coupling BY HAND until it is
seated on the gasket. DO NOT OVERTIGHTEN.
3. Attach the hose connected to the ‘C’ valve
to the cold water faucet.
Screw on the coupling
BY HAND until it is
seated on the gasket.
DO NOT OVERTIGHTEN.
H
C
Level the Washer-Dryer
After positioning the washer in it’s final installation
location, you must level the washer.
The front feet are self
locking and adjustable.
Your machine will be
noisy if the two front feet
are not adjusted so the
machine stands firm and
level.
1. Tilt the machine
back, leaning it
against the wall.
4. Turn on the water
faucets and check for
leaks.
IMPORTANT!
The couplings should be tightened BY HAND,
a tool should only be used if a leak occurs. Do
not use excessive force.
Secure the Drain Hose
1. Drape the power cord over the washer top.
2. Secure the drain hose to the laundry tub leg or
standpipe with a strap or cable-tie.
3. Use the U-Clamp (provided) and insert the drain hose
into the standpipe or sink. DO NOT force excess drain
hose into the standpipe. There should be only 6” of
drain hose in the stand pipe.
2. Adjust the front feet up or down to ensure the
washer is resting solid and does not rock side-toside or front-to back when the machine is upright.
IMPORTANT!
When moving washer to it’s final location,
take care not to kink the inlet or drain hoses.
Optional
Splendide SecureFit™
Installation Brackets, Part
No. MK01
• Hook around two front feet
and screw into the floor.
• Designed to keep the washer
from shifting front-to-back or
left-to right.
• Recommended for RV or
Marine Installations.
SecureFit Brackets,
Part No. MKO1
U-Clamp
6" max.
Standpipe
25" (62 cm) min.
34" (86 cm) max.
20" (50 cm) min.
with an air break
DID YOU KNOW?
The majority of problems with noisy
machines or excessive vibration are due
to the transit SCREWS/SPACERS NOT
BEING REMOVED or the FEET NOT BEING
ADJUSTED correctly to level the machine.
17
Installation Instructions
Complete the Installation
•
•
•
•
Check to be sure all parts are now installed. If
there’s an extra part, go back through the steps to
see which step was skipped.
Check to be sure you have all your tools.
Dispose/recycle all packaging materials.
Read this manual.
! WARNING
ELECTRICAL SHOCK HAZARD
Plug washer-dryer into a
grounded 3 prong outlet.
Do not remove ground prong.
Do not use adapter.
Final Installation Checklist
 Instructions and Installation Kit have been re






moved from the tub.
Transit bolts/spacers have been removed.
Washer is plugged into electrical outlet and is
properly grounded.
Water hoses are connected to the faucets with
inlet screens and washers.
Water is turned on and checked for leaks at
faucet and water valve connections.
Drain hose is properly located into drain facility
and is not collapsed or damaged.
Washer has been leveled.
Test for proper operation (see below)
To test and clean the washer
Measure 1 to 2 tbsp. of powdered High Efficiency (HE)
detergent.
• Pour the detergent into
compartment 2 in the
dispenser drawer (see
Dispenser Drawer).
• Select program “4” on the
PROGRAMS dial.
• Select HOT on the TEMPERATURE knob
• Press the ON-OFF button
(in). Allow the washer to
complete the full cycle. (It
will take approx. 40 min.)
18
Do not use an extension cord.
Failure to follow these
instructions can result in death,
fire, or electrical shock.
IMPORTANT!
Should you move residence in the future,
the Transit Screws/Spacers should be
reinstalled to support the inside of the
washer and prevent damage WHEN
TRANSPORTING.
Notes
19
© Copyright 2006, Westland Sales, Clackamas, OR 97015
1-800-356-0766
www.westlandsales.com
Download PDF

advertising