System information | Aroma ARC-743-1NGB Rice Cooker User Manual

$50('
5($'<
9 6<67(0
Using Your
XP-400
Security System
=21( =21( =21( =21( NAPCO
Oi220a
page 1
Tuesday, September 16, 1997 08:30
2
Oi220a
page 2
Tuesday, September 16, 1997 08:30
Introduction
Congratulations on your purchase of an advanced NAPCO EXPRESS XP-400 Security System. Meticulously developed
by a leading manufacturer of state-of-the-art security products, this system will provide you with unprecedented peace-of-mind &
incorporates some of the most sophisticated features available today. Above all, it has been designed an extra step, to provide
all those operating it with very easy, intuitive use. Please carefully review the information contained in this manual, so that you
and all potential users of the system familiarize yourselves with its operation, and can therefore take full advantage of EXPRESS’
many convenience features and amenities.
Your system consists of a control panel (a computer housed within a white metal panel enclosure), one or more EXPRESS
Decorator Keypads for controlling the system, and various security detection devices. These detection devices are divided
among separate areas known as “zones”, set up throughout your premises. Each zone number corresponds to a Zone light on
your Keypad’s gray display area.
When a zone’s red light is ON (or lit), it indicates that one or more detection device(s) assigned to that area are active o r open.
For example, if Zone 1 is the front door, and it is open, the Zone 1 light will be on. If zone 2 is a motion detector, and the re is
movement in that area, Zone light 2 will turn ON. Depending upon the actual layout your security professional has chosen to
properly protect your premises, each zone may function a little differently: The zone protecting your front door may be
programmed as an Exit/Entry zone to allow you time to enter the premises disarm the system , without inadvertently sounding
the alarm. Alternatively, a zone protecting a window could be designated as an “instant” zone, so that if it is entered or opened
while the system is on/armed, there will be an immediate alarm.
Your easy NAPCO EXPRESS Keypad puts super-simple system control at your fingertips. Most keypad commands
involve entering your four digit User Code. This includes Arming (or activating) and Disarming (or deactivating) the system.
Simply put, ARMED means the system is ON; DISARMED means the system is OFF. If the system is OFF and you want to turn
it ON, just enter your Code. To turn the system back OFF, enter your code again. It’s easy, just always remember, in the
event of an alarm, entering your User Code will silence all Sirens. Your keypad is your command and status center, it keeps
you informed visibly, using its zone and status lights (in the gray display area) and audibly, using its built-in keypad sounder. For
more information, please see Keypad Controls and Indicators on page 5.
3
Oi220a
page 3
Tuesday, September 16, 1997 08:30
Introduction
Table of Contents
Keypad Controls and Indicators ................................
Arming your System (When Leaving) .......................
Bypassing Zones .....................................................
Protecting Yourself While Home ...............................
Emergency Keys .......................................................
Disarming the System ...............................................
Silencing an Alarm.....................................................
Special Functions .....................................................
Programming User Codes .........................................
System Troubles .......................................................
Glossary ...................................................................
System Information
5
6
6
Central Station Phone Number: ____________________
Central Station Account Number: ____________________
7
8
For Service Call: ____________________
9
9
10
11
12
15
Entry Delay:
Exit Delay:
____________________
____________________
Alarm Time-out: ____________________
Important - Test Your System Weekly !
1 Bell / Battery Test
Test your bell or siren by pressing
followed by
.
This will cause the bell, or siren to sound for 2 seconds and
also initiate a test of the battery .
2 Central Station Communication Test
(This test should only be performed on weekends or at a
time designated by your alarm company)
1. Notify Central Station of the impending test.
2. Secure all zones to light Ready Light on your keypad.
3. Enter your user code to Arm the system.
4. Violate your alarm by opening a window / door etc.
5. The siren or bell should sound and the system will send
the alarm signals to the Central Station
6 . Enter your user code to silence the bell or sounder.
7. Call Central Station to insure that the alarm signals were
received properly.
4
Oi220a
page 4
Tuesday, September 16, 1997 08:30
Keypad Controls and Indicators
Key Used to enable
special functions and options. Press and then
the corresponding Special Function number Option (See Special Functions, Page 10)
Bypass Key Used to
bypass zones. Press
Bypass and the corresponding zone number,
and then Arm system.
Emergency Keys Press
simultaneously to signal
an emergency condition.
Press $ +$ for
Auxiliary Emergency or
3 +3 for Police Emergency. (Programmable)
Numerical Keys 1-9, 0. Used to enter
User Codes, Zone numbers, etc.
$50('
5($'<
Armed Light will light when system is Armed,
and will flash when system is in Alarm
Ready Light will light when all zones are secure
and system is ready to be Armed.
96<67(0
9 System Light will light and the Keypad
=21( =21( sounder will pulse to indicate that a system trouble is present.
(See System troubles, Page 12)
=21( =21( NAPCO
9 Key Press to display any present
System troubles. Only available when
9 System Light is lit.
Zone Lights (1 through 4) will light to indicate
that the corresponding Zone is open, and will
flash to indicate a zone in alarm.
Key - (Reset) used
to clear miss-entered
codes, reset Alarm Memory, etc..
(See System troubles, Page 12)
5
Oi220a
page 5
Tuesday, September 16, 1997 08:30
Arming Your System
Arming Your System When Leaving
1
Before arming your system, make sure the Green Ready light is ON. This indicates that all of your protective zones are secure. If any zones are open, the corresponding Zone light will be ON. Secure these
zones before proceeding. If any zones cannot be secured, see Bypassing zones below.
2
Enter your user code. The Green Ready light will go out, the Red Armed light will light.
• If you make a mistake entering your code, press
and re-enter the code.
3
Leave the premises through the Exit/Entry door. If the keypad gives a steady tone you have taken
too long. Enter your code again to disarm system and then re-enter code and leave.
ARMED
READY
SYSTEM
Easy Arm
The Easy Arm feature allows the system to be armed by simply pressing
followed by
allow the easy arming of the system by someone who is not a regular system user.
ZONE 1
ZONE 2
ZONE 3
ZONE 4
. This will
Bypassing Zones
If an open zone cannot be immediately fixed it can be left unprotected, or Bypassed ,while the rest of the
system is Armed. To Bypass a zone:
1
2
3
Press
followed by the zone number to be Bypassed. The Bypassed zone’s light will flash slowly.
Enter your user code. The Green Ready light will go out and the Red Armed light will light.
Leave the premises through the Exit/Entry door.
When the system is subsequently disarmed, all bypassed zones will be reset, ready to be armed again.
If it is necessary to bypass any inoperative zone(s), it is important to have the zone(s) repaired as soon as
possible. A bypassed zone does not provide any protection, compromising system security.
6
Oi220a
page 6
Tuesday, September 16, 1997 08:30
Arming Your System
Protecting Yourself While at Home
1 Before arming your system, make sure the Green Ready light is ON. This indicates that all of your
protective zones are secure. If any zones are open, the corresponding Zone light will be ON. Secure
those zones before proceeding.
2
3
ARMED
READY
SYSTEM
•
#
Enter your user code. The Green Ready light will go out, and the red Armed light will light.
to bypass any interior zones, deactivating devices such
Before your exit delay expires, press
as motion sensors, and allowing free movement throughout the premises. The Zone light of any
bypassed zones will flash slowly.
Your system may have been programmed for Automatic Interior Bypass , in which case it will
recognize that you have not left the premises and will automatically bypass any interior zones.
!
Instant Mode
ZONE 1
ZONE 2
ZONE 3
ZONE 4
Pressing
will cancel the Entry delay , activating the “Instant” mode. This is typically
followed by
done in the evening when all family members are home for the night. Instant Mode can be activated at any
time after the system has been armed. The Red Armed light will flash rapidly while in the Instant Mode.
Easy Exit (optional)
Your System may have been programmed to allow Easy Exit, which allows a user to exit the premises
followed by
, the protection is removed from the Exit/ Entry
with the system armed. By pressing
zone for 3 minutes. This will allow, for example, an early morning commuter to exit the house in the
morning, without having to disarm and rearm the system, waking the family.
Arming With a System Trouble Present (the 9 System Light is Lit)
9
If the XP400 has a system trouble present, the SYSTEM light will be lit and the keypad sounder
pulsing. If you cannot immediately clear the system trouble, the system can still be armed. Simply
to view the trouble, press
again to reset the trouble and then arm the system.
press
For more information, refer to page12. Note: System troubles should be repaired as soon as possible.
7
Oi220a
page 7
Tuesday, September 16, 1997 08:30
Emergency Conditions
&&
Yes
Yes
Emergency Buttons
Auxiliary
Emergency
Enabled?
Auxiliary Alarm:
Police
Emergency
Enabled?
Ambush
Alarm
Enabled?
Yes
No
The two sets of emergency buttons, if programmed, are always active whether the system is armed or
disarmed. Discuss these buttons with your installer. The emergency signal will only be activated when
the two respective buttons are pressed at the same time.
No
No
&
+
to alert the central station of an auxiliary
Simultaneously press
emergency, if so programmed.
(The nature of this emergency alarm is to be determined by the installer)
+
to sound a police emergency alarm, and to alert
Police Emergency: Simultaneously press
the central station of a fire emergency, if so programmed.
Ambush Alarm
In the event that you are forced by an intruder to disarm your system, the ambush alarm can be
activated. Disarming the system with the Ambush Code will cause the system to disarm and
simultaneously send a silent ambush alarm signal to Central Station. If your system has the Ambush
feature enabled, the code assigned as the User 4 code will function as your Ambush Code.
8
Oi220a
page 8
Tuesday, September 16, 1997 08:30
Disarming Your System / Silencing an Alarm
Disarming Your System when Returning
ARMED
READY
1
Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to remind you to
disarm the system before your Entry Delay time expires.
2
Enter your user code. The Red Armed light will go out, indicating that the system has been disarmed.
key and re-enter the code.
Note: If you make a mistake entering your code, press the
SYSTEM
Alarm Indication
If the Red Armed light is flashing rapidly, an alarm occurred while you were away.
Proceed with caution!
For your own protection, leave immediately and call authorities from a neighbor’s phone .
ZONE 1
ZONE 2
ZONE 3
ZONE 4
Silencing an Alarm
In the event that the system goes into alarm due to a violated burglary zone, the bell or siren will sound and
the keypad sounder will also activate. To silence the system, enter your User code. The zone light of the
is pressed to reset the alarm memory.
zone which went into alarm continue flashing until
9
Oi220a
page 9
Tuesday, September 16, 1997 08:30
Special Functions By pressing
be enabled:
followed by the appropriate key, (do not press simultaneously) these special functions and features can
!
Easy Arm (when system is disarmed)
The Easy Arm feature allows the system to be armed by
followed by
. This will allow the easy
pressing
arming of the system by someone who is not a regular
system user.
!
Easy Exit (when system is armed)
This function (if programmed) allows an occupant to leave
the premises without disarming the system. Pressing
followed by
while the system is armed will start a 3
minute period, during which you can leave through the
Exit/ Entry door.
Bell / Battery Test
followed by
will cause the bell, or siren to
Pressing
sound for 2 seconds. This will also initiate a test of your
battery to make sure it is adequately charged. The XP-400
also performs an automatic battery test very 24 hours
Access Output
followed by
will activate
If programmed, pressing
the Access Output which may be configured to open a
door strike, turn on lighting, or activate some other special
feature your installer has provided.
Instant Mode
followed by
will cancel the Entry delay
Pressing
and put the system into the “Instant” mode. This is typically done in the evening when all family members are home
for the night. When the system is disarmed, the Instant
mode will be canceled.
Chime Mode On / Off
followed by
will activate / deactivate the
Pressing
door chime. Activating this feature will cause any door
to beep the keypad sounder when it is opened.
Program Mode
followed by
will enable the “Program
Pressing
Mode”, which will allow you to program and erase user
codes. (see Programming user codes, page 14)
Kepad Sounder On / Off
followed by
will deactivate / activate the
Pressing
keypad sounder, depending on its present state. By
activating sleep mode on a keypad installed in a bedroom,
for example, you effectively turn off that keypad’s sounder.
However, any other keypads on the system will still sound
normally.
10
Oi220a
page 10
Tuesday, September 16, 1997 08:30
Programming User Codes
Your Installer has assigned a User 1 Code which may be used to not only Arm and Disarm the system, but
also to enter the User Program Mode, where you can program and/or reprogram up to 4 User Codes. The
following explains how you will use this code to program or erase additional user codes.
Entering the User Program Mode
ARMED
READY
SYSTEM
Press
followed by
and then enter the User 1 code. The Armed, Status and 9System Lights
will flash, and the keypad will beep 4 times. You are now in the User Program mode.
Zone lights 1 through 4 will light to indicate any User Codes presently programmed.
Programming / Reprogramming User Codes
1 Press the User number to be programmed. (For example, press
ZONE 1
ZONE 2
ZONE 3
ZONE 4
2
3
to program the User 2 code.).
The keypad will beep 2 times and the corresponding Zone light will flash to indicate the user
number you are about to program.
Press in the 4 digits of the new User 2 code, the keypad will beep 4 times.
If there are more user codes to be programmed, return to step 1 above, otherwise, go to Exiting the
User Program Mode below.
Erasing a User Code
1 Press the User number to be erased. The keypad will beep 2 times and the corresponding Zone light
will flash to indicate the user number you are about to erase.
. The zone light will go out to indicate that the user code has been erased.
2 Press
3 If there are more user codes to be erased, return to step 1 above, otherwise, go to Exiting the user
Program Mode below.
Exiting the User Program Mode
When you are done programming or erasing User codes, press
to Exit the User Program Mode.
11
Oi220a
page 11
Tuesday, September 16, 1997 08:30
9System Troubles
The XP400 is constantly monitoring its own components, as well as all critical services, such as AC Power
and the Telephone line, to insure that it is always ready to provide the protection for which it was designed.
When a system trouble does occur, it will caution you by lighting the Yellow 9SYSTEM light and beeping the
keypad buzzer. If you cannot immediately clear the system trouble, the system can still be used. Simply
to view the trouble as described below, and then arm the system.
press
ARMED
READY
SYSTEM
Keypad Beeps or
Zone light
ON
Flashes
9SYSTEM
System Trouble
Condition
Action
1 Beep
1
AC Power Failure
This trouble will occur if AC power is not present. Make sure
system transformer is plugged into AC receptacle and check
circuit breaker, otherwise call installing company for service.
1 Beep
2
Low Battery
If there has been a recent power failure, the battery may be
partially depleted and must be recharged by the control
panel. If the trouble does not go away in 24 hours, call installing company for service.
1 Beep
3
Communication
Failure
The system was not able to report to central station. If this is
due to a temporary interruption in the telephone service, the
trouble can be cleared when the service is restored by pressing
. Otherwise, call installing company for service.
1 Beep
4
Telephone Line Cut
The telephone line has failed. If telephone service has been
temporarily interrupted, the trouble will clear it is when restored. Otherwise, call installing company for service.
ZONE 1
ZONE 2
In order to determine the nature of the trouble, press
, count the number of keypad beeps and observe
the number of the illuminated zone light. Refer to the following table to determine the cause of the trouble.
will scroll to the next, and then exit the
If there is more than one trouble to be viewed, pressing
9SYSTEM mode if there are no additional troubles to view.
ZONE 3
ZONE 4
12
Oi220a
page 12
Tuesday, September 16, 1997 08:30
9System Troubles
Keypad Beeps or
Zone light
ON
Flashes
9SYSTEM
ARMED
System Trouble
Condition
Action
2 Beeps
1
Bell / Siren Trouble There is a problem with the Bell or Siren. Call installing company for service.
2 Beeps
3
Wireless Receiver
Trouble
A problem has been detected with the wireless receiver.
Call installing company for service.
2 Beeps
4
Wireless Receiver
Jam
A problem has been detected with a wireless receiver.
Call installing company for service.
3 Beeps
1-4
Wireless
Transmitter Low
Battery
The battery in a wireless transmitter is low and should be replaced. This transmitter is on the zone corresponding to the
number of the lit zone light. The replacement battery for the
GEM-Trans2 door/window transmitter, GEM-PIR motion detector and GEM-GB glass break detector is the Duracell
DL123A. (2 required for the GEM-PIR and GEM-GB.) The
GEM-DT Dual Technology Sensor requires 4 C-Cell Duracell
MN1400 Alkaline batteries.
Warning: Replace batteries only with the same type as specified above. Use of another battery may present a risk of fire or
explosion. Do not recharge or disassemble battery, or dispose
of in fire.
4 Beeps
1-4
Wireless
Transmitter
Supervisory Failure
A problem has been detected with a wireless transmitter.
Call installing company for service
7 Beeps
1-4
Zone Trouble
Call installing company for service.
READY
SYSTEM
ZONE 1
ZONE 2
ZONE 3
ZONE 4
13
Oi220a
page 13
Tuesday, September 16, 1997 08:30
Glossary
Ambush Code - In the event that
you are forced by an intruder to disarm your system, this special code
can be used to disarm the system,
and simultaneously send a silent
alarm to Central Station. If your system has the Ambush feature enabled,
the code assigned as the User 4 code
will function as your Ambush Code
Arming / Disarming - Turning the
system on or off by entering your user
code at the keypad.
Auto Interior Bypass - A feature
which allows the system to recognize
when you have not left the premises
and automatically bypass any interior
zones, deactivating devices such as
motion sensors, allowing free movement throughout the premises.
Battery - A backup source of power
to provide protection for a limited time
in the event of a power failure.
Bypass - the manual or automatic
removal of one or more protection
zones from the system. Press
14
Oi220a
page 14
and then the zone number to bypass a
zone.
Central Station - Monitors alarm,
emergency and trouble reports from the
alarm system and notifies proper authorities.
Chime - a keypad beep which indicates that a door has been opened while
the system is disarmed.
Easy Exit - Allows an occupant to
leave the premises without disarming
and then
the system. Pressing
while the system is armed will
permit exit by removing the protection
on the Exit/Entry door for 3 minutes,
Exit/Entry Delay - The amount of
time you are allowed to enter and leave
the premises when the system is armed.
Exit/Entry Zone - A zone which will
allow you to enter and leave the
premises when the system is armed.
Instant Protection - Arming without
Entry Delay while remaining on the
premises.(Press
while armed)
Keypad Sounder - A local warning
device at the keypad to alert that Entry
delay has started,
System Trouble - A problem has
been detected in the system which
may prevent it from working properly.9SYSTEM light will be lit.
User Code - A four digit code which
is used to arm and disarm the system
from the keypad.
User 1 Code - A four digit code
which can be used to program, reprogram and erase user codes, as
well as arm and disarm the system
from the keypad.
Zone - An area which is protected by
a security device. Your front door may
be designated as Zone 1, while the
living room motion detector may be
Zone 2. Refer to the Zone Label on
your keypad for the Zone Identification
of your system.
Tuesday, September 16, 1997 08:30
Notes
15
Oi220a
page 15
Tuesday, September 16, 1997 08:30
NAPCO LIMITED WARRANTY
NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants its products to be free from manufacturing defects
in materials and workmanship for thirty-six months following the date of manufacture. NAPCO will, within
said period, at its option, repair or replace any product failing to operate correctly without charge to the
original purchaser or user.
This warranty shall not apply to any equipment, or any part thereof, which has been repaired by others,
improperly installed, improperly used, abused, altered, damaged, subjected to acts of God, or on which any
serial numbers have been altered, defaced or removed. Seller will not be responsible for any dismantling or
reinstallation charges.
nor authorizes any other person purporting to act on its behalf to modify, to change, or to assume for it, any
other warranty or liability concerning its products.
In no event shall NAPCO be liable for an amount in excess of NAPCO's original selling price of the product,
for any loss or damage, whether direct, indirect, incidental, consequential, or otherwise arising out of any
failure of the product. Seller's warranty, as hereinabove set forth, shall not be enlarged, diminished or
affected by and no obligation or liability shall arise or grow out of Seller's rendering of technical advice or
service in connection with Buyer's order of the goods furnished hereunder.
NAPCO RECOMMENDS THAT THE ENTIRE SYSTEM BE COMPLETELY TESTED WEEKLY.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF. THERE IS NO EXPRESS OR IMPLIED WARRANTY OF MERCHANTABILITY OR
A WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. ADDITIONALLY, THIS WARRANTY IS IN
LIEU OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF NAPCO.
Any action for breach of warranty, including but not limited to any implied warranty of merchantab ility, must
be brought within the six months following the end of the warranty period.
IN NO CASE SHALL NAPCO BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE
LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT.
In case of defect, contact the security professional who installed and maintains your security system. In
order to exercise the warranty, the product must be returned by the security professional, shipping costs
prepaid and insured to NAPCO. After repair or replacement, NAPCO assumes the cost of returning products
under warranty. NAPCO shall have no obligation under this warranty, or otherwise, if the product has been
repaired by others, improperly installed, improperly used, abused, altered, damaged, subjected to accident,
nuisance, flood, fire or acts of God, or on which any serial numbers have been altered, defaced or removed.
NAPCO will not be responsible for any dismantling, reassembly or reinstallation charges.
This warranty contains the entire warranty. It is the sole warranty and any prior agreements or representations, whether oral or written, are either merged herein or are expressly cancelled. NAPCO neither assumes,
THE FOLLOWING STATEMENT IS REQUIRED BY THE FCC.
This equipment generates and uses radio-frequency energy and, if not installed and used properly, that
is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television
reception. It has been type tested and found to comply with the limits for a Class-B computing device in
accordance with the specifications in Subpart J of Part 15 of FCC Rules, which are designed to provide
reasonable protection against such interference in a residential installation.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause interference to radio or television reception, which can be determined by turning the
NAPCO Security Systems, 333 Bayview Avenue, Amityville, NY 11701
Oi220a
page 16
Warning: Despite frequent testing, and due to, but not limited to, any or all of the following; criminal
tampering, electrical or communications disruption, it is possible for the system to fail to perform as
expected. NAPCO does not represent that the product/system may not be compromised or circumvented; or
that the product or system will prevent any personal injury or property loss by burglary, robbery, fire or
otherwise; nor that the product or system will in all cases provide adequate warning or protection. A properly
installed and maintained alarm may only reduce risk of burglary, robbery, fire or otherwise but it is not
insurance or a guarantee that these events will not occur. CONSEQUENTLY, SELLER SHALL HAVE NO
LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE, OR OTHER LOSS BASED ON A CLAIM
THE PRODUCT FAILED TO GIVE WARNING. Therefore, the installer should in turn advise the consumer to
take any and all precautions for his or her safety including, but not limited to, fleeing the premises and ca lling
police or fire department, in order to mitigate the possibilities of harm and/or damage.
NAPCO is not an insurer of either the property or safety of the user's family or employees, and limits its
liability for any loss or damage including incidental or consequential damages to NAPCO's original selling
price of the product regardless of the cause of such loss or damage.
Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion or
limitation of incidental or consequential damages, or differentiate in their treatment of limitations of liability
for ordinary or gross negligence, so the above limitations or exclusions may not apply to you. This Warranty
gives you specific legal rights and you may also have other rights which vary from state to state.
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures: reorient the receiving antenna; relocate the computer with respect to the receiver;
move the computer away from the receiver; plug the computer into a different outlet so that computer and
receiver are on different branch circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for
additional suggestions. The user may find the following booklet prepared by the Federal Communications
Commission helpful: “How to Identify and Resolve Radio-TV Interference Problems”. This booklet is
available from the U.S. Government Printing Office, Washington, DC 20402; Stock No. 004-000-00345-4.
OI220A 08/97
Tuesday, September 16, 1997 08:30
Download PDF

advertising