Arrow Storage Products 697.68103

Owner's Manual & Assembly Instructions
SP01
Model No.
CM1014-A1
697.68103-C1
OB1014-C1
697.68104
CAUTION: SOME PARTS HAVE SHARP EDGES. CARE
MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES
TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ
SAFETY INFORMATION PROVIDED IN THIS MANUAL
BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES
WHEN HANDLING METAL PARTS.
714740408
BUILDING DIMENSIONS * Size rounded off to the nearest foot
*Approx.
Size
10' x 14'
Foundation
Size
121" x 160 1/4"
3,0m x 4,0m 307cm x 407cm
Storage Area
Sq. Ft. Cu. Ft.
129
12,0m2
769
21,8m3
Exterior Dimensions
(Roof Edge to Roof Edge)
Width
Depth
Height
123 1/4"
313cm
162 3/4"
413cm
81 3/8"
207cm
Interior Dimensions
Door
(Wall to Wall)
Opening
Width Depth Height Width Height
118 1/4"
300cm
157 1/2"
400cm
80 1/8" 55 1/2"
204cm
141cm 152cm
60"
BEFORE YOU BEGIN....
A2
Owner's Manual
Before beginning construction, check local building codes regarding footings, location
and other requirements. Study and understand this owner's manual.
Important information and helpful tips will make your construction easier and more
enjoyable.
Assembly Instructions:
Instructions are supplied in this manual and contain all
appropriate information for your building model. Review all instructions before you begin,
and during assembly, follow the step sequence carefully for correct results.
Foundation and Anchoring: Your storage building must be anchored to prevent wind
damage. A foundation is also necessary as a base in order to construct a square and level
building. Anchoring and foundation materials are not included with your building. We
recommend the combined use of an Arrow Floor Frame Kit and an Arrow Anchoring
Kit as an effective method of securing your building to the ground (Available by mail order
or at your local dealer) or you may construct a foundation and anchoring system of your
choice. Your assembly instructions provide information on a few methods commonly used
to secure and level a storage building.
Parts and Parts List: Check to be sure that you have all the necessary parts for your
building.
•All part numbers can be found on the parts. All of these numbers (before the -) must agree with the
numbers on the parts list. The parts list is located on page 12.
•If you find that a part is missing, include the model number of your building and contact:
Arrow Group Industries, Inc. Customer Service Department
Route 50 East Breese, Illinois 62230
1-800-851-1085
•Separate contents of the carton by the part number while reviewing parts list. The first few steps
show how to join related parts to make larger sub assemblies which will be used later.
•Familiarize yourself with the hardware and fasteners for easier use during construction. These are
packaged within the carton. Note that extra fasteners have been supplied for your convenience.
2
PLAN AHEAD....
A3
Watch the Weather: Be sure the day you select to install your building is dry and calm.
Do not attempt to assemble your building on a windy day. Be careful on wet or muddy ground.
Teamwork:
Whenever possible, two or more people should work together to assemble
your building. One person can position parts or panels while the other is able to handle the
fasteners and the tools.
Tools and Materials:
These are some basic tools and materials you will need for the
construction of your building. Decide which method of anchoring and the type of foundation
you wish to use in order to form a complete list of the materials you will need.
Required
• Eye Goggles
• No. 2 Phillips Screwdriver
(With Hardened Magnetic Tip)
Note: A power screwdriver or variable speed drill with Phillips-tip attachment can speed assembly by
as much as 40%.
Required
• Work Gloves
• Step Ladder
• Utility Knife / Scissors
• Pliers
• Carpenter's Level
• Tape Measure
Optional Time-Savers
• Wrench / Nut Driver
• Electric / Cordless Drill
• Square
• String (for squaring frame)
Foundation Preparation
• Hammer and Nails
• Spade or Shovel
• Hand Saw / Power Saw
• Lumber and/or Concrete
Selecting and Preparing Your Site:
Before assembly, you will want to decide on
a location for your building. The best location is a level area with good drainage.
•Allow enough working space for ease of moving parts into position during assembly. Be sure there
will be enough space at entrance for doors to open fully and enough space around the building to
be able to fasten the panel screws from the outside.
•Before you begin the first steps in assembling your parts, a foundation should be constructed and
an anchoring system should be ready to use.
3
SAFETY FIRST....
A4
Safety precautions are important to follow throughout the construction of your building.
•Care must be taken when handling various
pieces of your building since some contain
sharp edges. Please wear work gloves, eye
protection and long sleeves when assembling
or performing any maintenance on your building.
•Practice caution with the tools being used in the
assembly of this building. Be familiar with the
operation of all power tools.
safety edge
sharp edge
sharp edge
safety edge
•Keep children and pets away from worksite to
avoid distractions and any accidents which
may occur.
•Do not attempt to assemble the building if parts
are missing because any building left partially
assembled may be seriously damaged by light
winds. Call 1-800-851-1085
•Never concentrate your total weight on the
roof of the building. When using a step ladder
make sure that it is fully open and on even
ground before climbing on it.
•Do not attempt to assemble the building on a
windy day, because the large panels acting as a
"sail", can be whipped about by the wind making
construction difficult and unsafe.
4
CARE & MAINTENANCE....
A5 Web
Finish:
For long lasting finish, periodically clean and wax the exterior surface. Touchup scratches as soon as you notice them on your unit. Immediately clean the area with
a wire brush; wash it and apply touch-up paint per manufacturer's recommendation.
Roof: Keep roof clear of leaves and snow with long handled, soft-bristled broom. Heavy
amounts of snow on roof can damage building making it unsafe to enter. In snow country,
Roof Strengthening Kits are available for most Arrow Buildings for added protection
against heavy snow accumulation.
Doors: Always keep the door tracks clear of dirt and other debris that prevent them from
sliding easily. Lubricate door track annually with furniture polish or silicone spray. Keep
doors closed and locked to prevent wind damage.
Fasteners: Use all washers supplied to protect against weather infiltration and to protect
the metal from being scratched by screws. Regularly check your building for loose screws,
bolts, nuts, etc. and retighten them as necessary.
Moisture:
A plastic sheet (vapor barrier) placed under the entire floor area with good
ventilation will reduce condensation.
Other Tips....
• Wash off inked part numbers on coated panels with soap and water.
• Silicone caulking may be used for watertight seals throughout the building.
Do not store swimming pool chemicals in your building. Combustibles and
corrosives must be stored in air tight approved containers.
Keep this Owner's Manual and Assembly Instructions for future reference.
5
ACCESSORIES....
A6 WEB
ROOF STRENGTHENING
(heavy snow load) KITS
FLOOR FRAME KITS
Extra roof beams and gable braces
designed for added protection against
heavy snow accumulation. Increases
the strength of your roof by 50%.
ANCHOR KITS
Model No. AK4
Anchor Kit contains heavy-duty steel
augers, 60' (18m) of steel cable and 4 cable
clamps. No digging or concrete
pouring, just insert cable under roof,
over roof beams, into augers and twist
augers into the ground. For buildings
larger than 10'x9', use 2 kits.
Model No. AK100
New concrete anchor system permits
anchoring any size Arrow building
directly to a concrete slab. Each kit
contains heavy-duty, hot-dipped
galvanized steel corner gussets and
perimeter clips which fit over the floor
frame and lag bolt into a concrete slab.
Full assembly instructions and a 1/4"
masonary drill bit are included.
Model No. AK600
Earth Anchor Kit anchors any size
Arrow building to the ground.
Each kit contains heavy duty,
hot-dipped galvanized steel
corner gussets and 4 earth anchors.
MODELS FB47410, FB5465, FB106-A
FB109-A and FB1014-A
A simple new floor frame system made of heavy-duty, hot-dipped
galvanized steel. Use as foundation for plywood, sand or stone.
ATTIC KIT / WORKBENCH KIT
Heavy-duty galvanized steel bars that
fit all 10' wide Arrow buildings. They
install quickly and easily to help
organize space and create more
useable space as an attic or
workbench. Will hold up to 250 lbs.
(113kg) evenly distributed.
Model No.
AT101
Fits
Shipping Weight
10' Long, 250 lb. (113kg) load+
Fits all Arrow 10' wide buildings.
16 lbs. (7kg)
Must be drilled for use as workbench in Estator.
+ Even weight distribution.
SHELF UNITS
Heavy-duty, galvanized steel shelf units help organize storage
space. They easily mount on the wall or sit on the floor. Fits all
Arrow buildings.*
TOOL HANGING RACK
Model No. TH100
The perfect tool organizer. Twin
25 1/2" (65cm) steel channels
plus five heavy-duty snap-in
hangers and a small tool holder for
screwdrivers, pliers, etc. Holders
slide along channel for fully
adjustable spacing. Great for
garage, basement, or the back
of any door. Fits all Arrow
storage buildings.
Model No. SS404
• Makes 8" to 12" (20-30cm)
wide shelves in any length.
• Brackets, braces,
hardware included.
Lumber is not included.
Model No. SS900-A
• Grey color
• 3 shelves
• Holds up to 85 lbs. (38kg)
(even weight distribution)
* Some drilling required to fit buildings without mid-wall bracing.
6
THIS
PAGE
WAS
LEFT
BLANK
INTENTIONALLY
7
THIS
PAGE
WAS
LEFT
BLANK
INTENTIONALLY
8
Foundation
F09
The Foundation For Your Building
OPTION 1: ARROW FLOOR FRAME KIT:
(Order No. FB1014-A or 68387-A)
Arrow has the best base for your building in this simple kit. It keeps stored items above the ground.
This kit should be used with one of the following:
A. To support a plywood deck B. To be filled with sand. We recommend the combined use of
1. an ARROW FLOOR FRAME KIT and 2. an ARROW ANCHORING KIT as an effective method of securing the building to the ground.
Allow 1 - 2 hours for construction.
OPTION 2: Wood Platform
If you decide to build your own foundation, be sure to select the appropriate materials.
These are the recommended materials for your foundation:
● 2 x 4's (5cm x 10cm) Pressure Treated Lumber ● 5/8" (1,5cm) 4 x 8 (122cm x 244cm) Plywood-exterior grade
● 10 & 4 penny Galvanized Nails ● Concrete Blocks (optional)
The platform should be level and flat (free of bumps, ridges etc.)
to provide good support for the building. The necessary materials
may be obtained from your local lumber yard.
"
/24
16" /61cm
6cm
40,
To construct the foundation follow instructions and diagram.
Construct frame (using 10 penny galvanized nails)
Measure 16"/24" (40,6cm/61cm) sections to construct
inside frame (see diagram)
Secure plywood to frame (using 4 penny galvanized nails)
121
3,1 "
m
FRONT
(DOOR)
Allow 6 - 7 hours for construction.
OPTION 3: Concrete Slab
"
1/4
160 1m
4,
Note: Platform/Slab will extend 9/16" (1,4cm) beyond floor
frame on all four sides. Seal this 9/16" of wood with a
roofing cement (not included), or bevel this 9/16" of
concrete when pouring, for good water drainage.
The slab should be at least 3" to 4" (8-10cm) thick. It must be level and flat to provide good support for the frame.
The following are the recommended materials for your foundation.
● 1 x 4's (2,5cm x 10cm) (will be removed once the concrete cures)
● Concrete ● Sheet of 6 mil plastic
● We recommend for a proper strength concrete to use a mix of:
1 part cement ● 3 parts pea sized gravel ● 2 1/2 parts clean sand
Prepare the Site/Construct a Foundation
1. Dig a square, 6" (15cm) deep into the ground (remove grass).
2. Fill up to 4" (10cm) in the square with gravel and tamp firm.
3. Cover gravel with a sheet of 6 mil plastic.
4. Construct a wood frame using four planks of 1x4 (2,5cm x 10cm)
lumber.
5. Pour in concrete to fill in the hole and the frame giving a
total of 4" (8-10cm) thick concrete. Be sure surface is level.
12
FRONT 3, 1"
1m
(DOOR)
/4"
01
6
1 ,1m
4
Note: Finished Slab dimensions, with lumber removed.
Allow 3 - 5 hours for construction and a week for concrete curing time.
9
Anchoring
A10
Anchoring Down The Building
It is important that the entire floor frame be anchored after the building is erected.
Below are recommended ways of anchoring.
Arrow Anchoring Kit: (Model No. AK4 or 60298)
Recommended for use with any suggested base.
Contains: 4 Anchors with Cable, Clamps and
installation instruction.
Anchoring into Wood/Post:
Use 1/4" Wood Screws. There are 1/4" (0,63cm) dia.
holes provided in the frames for proper anchoring.
1.
2.
OVER THE BEAMS
AND INTO THE GROUND
Arrow Anchoring Kit: (Model No. AK100 or 68383)
Recommended for use with the concrete foundation.
Contains: Corner gussets, perimeter clips, hardware,
1/4" masonary drill bit and installation instruction.
Anchoring into Concrete:
1. For poured concrete slab or footing or patio blocks:
Use 1/4" x 2" Lag Screws.
2. For Anchor Post of Concrete poured after building is
erected: Use 1/4" x 6" Lag Screws.
1.
10
2.
Hardware
SP11
Remove from bag of screws
and save for the last step
65103
#8-32 Hex Nut (192)
65900A
#10Bx1/2" Black Screw (8)
(Packed with Screws)
65923
#8-32x3/8" Bolt (192)
65004
#8Ax5/16" Screw (438)
66045
Handle (2)
66646
Washer (453)
(12 sheets of 40)
65109
#8-32 Acorn Nut (4)
(Packed with Screws)
67468
Peak Cap (2)
(Arrow Logo)
66769
Door Slide (4)
66382
Lower Door Guide (4)
66183
Roof Trim Cap
(2 right & 2 left)
6228
Track Support (2)
67545 21'
Weather Stripping (1)
11
Parts List
BZ12
12
Part
Number
Part
Description
8576
8577
10497
7743
9984
9983
10475
10475
9369
9373
6515
6020
3719
6278
6403
6892
6893
6015
6869
6797
9366
5986
10389
9365
6635
10386
10388
10391
10387
8936
9367
9009
9204
8934
Right Gable
Left Gable
Horizontal Door Brace
Roof Panel
Right Roof Panel
Left Roof Panel
Right Door
Left Door
Door Jamb
Front Wall Panel
Wall Panel
Corner Panel
Door Handle Brace
Vertical Door Brace
Door Track Splice
Rt. Side Roof Trim
Lt. Side Roof Trim
Side Roof Trim
Ridge Cap
Ridge Cap
Door Track
Rear Wall Angle
Rear Wall Channel
Front Wall Channel
Roof Beam Bracket
Roof Beam
Side Wall Channel
Side Wall Angle
Side Floor Frame
Rear Floor Frame
Front Floor Frame
Gable Brace
Roof Beam Brace
Ramp
Quantity Check
in Carton List
2
2
4
8
2
2
1
1
2
2
12
4
2
2
1
2
2
2
1
2
2
2
2
2
4
8
4
4
4
2
2
2
2
1
NOTES
GZ46
Step 1
● 8934 Ramp (1)
● 9367 Front Floor Frame (2)
● 8936 Rear Floor Frame (2)
● 10387 Side Floor Frame (4)
● Parts Needed For ●
Floor Frame Assemblies
SO14
The front floor frame is made up of
three pieces. The side floor frames
and the rear floor frame are made up
of two pieces. The holes in these
pieces will align when the pieces are
positioned with correct amount of
overlap. The illustrations below show
the proper overall length for the sides,
rear and front. Proceed as follows:
9367
8934
9367
8936
10387
1
Place the front floor frames as
shown. Center the ramp, with drain
holes facing outside, on top of the two
front floor frames. Join the frames by
inserting eight screws.
STEP
Front Floor
Frame Assembly
119 3/8" 3,0m
8934
1
9367
9367
DRAIN HOLES FACE
OUTSIDE
2 Overlap the side floor frames and
the rear floor frames as shown. The
holes in these pieces will align when
the pieces are positioned with correct amount of overlap. See the illustrations below for the proper overall
length of the side and rear floor frames.
Join the frames by inserting four/five
bolts into each frame set as shown.
10387
Side Floor Frame 158 5/8" 4,0m
10387
STEP
2
8936
Rear Floor Frame 119 3/8"
3,0m
8936
3
Double check the length of each
and set these pieces aside for later
use.
158 5/8" 4,0m
Sides
158 5/8" 4,0m
STEP
3
14
119 3/8" 3,0m
Front & Rear
119 3/8" 3,0m
Step 2
● Parts Needed For ●
Frame Assemblies
SO15
The main frame pieces reinforce the
walls. These pieces will later be installed in the center and at the top
edge of the side walls and the rear
wall. Proceed as follows:
● 5986 Rear Wall Angle (2)
● 10389 Rear Wall Channel (2)
● 10388 Side Wall Channel (4)
● 10391 Side Wall Angle (4)
Rear Wall Channel
118 1/8" 3,0m
10389
10389
1
Overlap the rear wall channel
pieces as shown in the figure and
fasten the two pieces together with
eight bolts as shown.
Side Wall Channels
157 3/8"
4,0m
10388
2 Make two side wall channels by
overlapping the side wall channel
pieces as shown. Fasten each set
together with eight bolts as shown.
10388
STEP
STEP
1
2
3
Overlap the rear wall angle
pieces as shown in the figure and
fasten them together with one bolt in
the center hole.
5986
4
Make two side wall angles by
overlapping the side wall angle
pieces as shown. Fasten each set
together with one bolt thru the second large hole from the end of each
part.
Rear Wall Angle
118 1/8" 3,0m
5986
Side Wall Angles
157 3/8" 4,0m
10391
10391
STEP
STEP
3
4
Rear Wall Channel 118 1/8" 3,0m
Side Wall Channels 157 3/8" 4,0m (2 Assemblies)
5 Set the assemblies aside. You will
use them later.
Rear Wall Angle 118 1/8" 3,0m
Side Wall Angles 157 3/8" 4,0m (2 Assemblies)
STEP
5
15
Step 3
● Parts Needed For ●
Roof Beam Assemblies
● 10386 Roof Beam (8)
SO16
The roof beams join the two gables
and support the roof panels. The main
roof beam is made up of four pieces
overlapped back to back at the center. The left and right roof beam assemblies are made up of two pieces.
Hint: These pieces are force-fitted,
so you may have to press hard to join
them together.
1
Place the end of one roof beam
inside a second roof beam so that the
six holes in each piece align. Make
four sets of roof beams by repeating
this procedure. Do not insert bolts
yet.
10386
10386
Roof Beam 159 3/8"
4,0m
STEP
1
STEP
ASSEMBLED
2
END
VIEW
2 Take two of the pressed-together
roof beams and join them as shown
to form the main roof beam assembly.
Hold the assembly together and fasten with 14 bolts. Build only one
Doubled Beam Assembly.
10386
Build one Doubled Main Roof
Beam Assembly for Peak in Roof
3
Fasten the other two pressedtogether roof beams with eight bolts
to make the left and right roof beam
assemblies.
4
Set these pieces aside for later
assembly.
10386
10386
STEP
3
10386
159 3/8"
4,0m
Build two Single Beam
Assemblies for Break in Roof
16
159 3/8"
4,0m
● Parts Needed For ●
Step 4
Door Track Assembly
● 6403 Door Track Splice (1)
● 9366 Door Track (2)
A17
NOTE:
Door Track Splice (painted part)
The door track assembly supports
the sliding doors and reinforces the
front wall. It is made up of three pieces.
6403
1
Using the door track splice,
(painted), join the door track
(galvanized) pieces end-to-end as
shown.
2 Insert four screws from the under-
66769
9366
9366
side only.
Hint: The holes in the top side of the
door track assembly are for fastening
the gable to the top of the front wall in
a later step.
STEP
STEP
1
2
Long Leg
on Top
Short Leg
on Bottom
9366
6403
9366
118 1/8"
3m
3
Position door slides onto the
legs, from the end of door track
assembly, as shown in the end view.
STEP
STEP
3
4
4 Set this piece aside for later use.
118 1/8"
END VIEW
3m
66769
118 1/8" 3m
17
Step 5
● Front Floor Assembly (1)
● Side Floor Assembly (2)
● Rear Floor Assembly (1)
● Parts Needed For ●
Floor Frame
SO18
RIGHT
REAR
10387
1
Place the floor frame pieces that
you assembled earlier on the foundation. Assemble the four corners of
the floor frame using two screws at
each corner as shown. At the front
corners fasten bolts through from
the bottom with nuts on top.
STEP
8936
1
FR
ON
T
RIGHT
FRONT
10387
9367
2
Measure the floor frame diagonally. When the diagonal measurements are equal, the floor frame is
square.
NOTE
If using a wood platform or
concrete slab do not fasten the
floor frames to your base at this
time. You will anchor the
building after it is erected.
NOTE
If you have purchased a Floor
Frame Kit you need to
install it at this time.
The floor frame must be square
and level or holes will not align.
18
When Diagonal Measurements
are Equal the Floor Frame
is Square.
STEP
2
Level
Step 6
● Parts Needed For ●
● 6515 Wall Panel (2)
● 9373 Front Wall Panel (2)
● 6020 Corner Panel (4)
Corners
SO19
Narrow
Side
NOTE
The remainder of the building assembly
requires many hours and more than one
person. Do not continue beyond this point
if you do not have enough time to complete the assembly today. A partially
assembled building can be severely
damaged by light winds.
6020
Wide Side
REAR
6020
Each screw and bolt in the wall requires a washer.
TOP VIEW
SIDE
1
Position a corner panel at the
corner of the floor frame as shown.
The widest part of each corner panel
must be placed along the side of the
building for all four corners. Fasten
the corner panel to the floor frame
with one screw.
STEP
SIDE
6020
6020
1
FRONT
6515
6515
Support the corner panel with a step
ladder until a wall panel is attached.
STEP
3
STEP
2 Attach the front wall panels to the
2
front corner panels, as shown. A small
gap will exist between front wall panel
and ramp.
3 Attach the wall panels to the rear
corner panels, as shown.
NOTE
Be careful to install the correct
panel in each position as shown
9373
9373
STEP
6515
4
6020
6515
6020
6020
9373
4 Double-check the part numbers of
the wall panels, before proceeding.
The floor frame must be square
and level or holes will not align.
6020
9373
Washer
Panels rest on
frame as shown
19
● Parts Needed For ●
Step 7
Mid Frames
● Rear Wall Channel Assembly (1)
● Side Wall Channel Assembly (2)
SO20
The mid frame pieces give rigidity to
the side and rear walls.
1
Fasten the rear wall channel
across the middle of the rear wall
using screws.
2
Fasten the side wall channels
across the middle of the side panels
using screws. Fasten overlaps in
rear corners with bolts and nuts, at
two locations. See the figure.
NOTE
The wall channels behind the
front wall panels will be installed
in a later step.
STEP
1
STEP
10389
2
10388
STEP
2
20
FRO
NT
● Door Track Assembly (1)
● Rear Wall Angle Assembly (1)
● Side Wall Angle Assembly (2)
● Parts Needed For ●
Step 8
Top Frames
SO21
The top frame pieces give rigidity to
the walls and provide a surface for
attaching the gables which support
the roof.
1 Fasten the rear wall angle across
the inside top of the rear wall using
screws.
2 Fasten the side wall angles across
the inside top of the side panels using screws. Side wall angles must
overlap rear wall angle in corners.
3 Fasten the door track assembly
(holes on top) across the top of the
front wall panels using screws. See
the figure.
Wall Angles
Must Face
Inside
Building
Long Leg
on Top
STEP
STEP
2
10391
1
5986
Opening
facing in
Short Leg
on Bottom
9366
STEP
3
DOOR T
RACK A
SSEMB
LY
FRO
NT
21
Step 9
● Parts Needed For ●
Wall Panels
● 6515 Wall Panel (10)
SO22
STEP
Each wall panel has a crimped rib on
one side. The crimped rib should go
under the rib of the panel that follows
it.
4
Crimped Rib
Underneath
STEP
2
1 Locate all of the wall panels and
6515
set each one alongside the building.
2 Fasten the wall panels at the top
Detail Showing
Center of Panel
Screwed to
Wall Channel
and bottom with screws.
3 Fasten the center of each panel to
the wall channel with screws.
4 Fasten overlapping ribs as before.
Panels rest on
frame as shown
6515
STEP
3
STEP
1
Use bolts and nuts
thru wall angle
overlap at the top
of panel at rear.
22
Bolt and nut
does not go
thru wall
channel at
overlap
Step 10
● Parts Needed For ●
● 9369 Door Jamb (2)
● 9365 Front Wall Channel (2)
Front Channel/Door Jamb
SO23
The door jambs reinforce the door
opening and provide an attractive
trim. Follow these steps for both
door jambs.
9365
T
1
ON
STEP
in their positions between the end of
the side wall channel and the corner panel using screws. Do not put
a screw in the hole at the end behind the door opening at this time.
FR
1 Fasten the front wall channels
INSIDE OF
BUILDING
STEP
(2) bolts
2
TOP VIEW
Door Track
Acorn Nut
2 Fasten a door jamb to the front
panel with two bolts, nuts and acorn
nuts, as shown.
9369
Bolt
Hex Nut
TOP VIEW
3
Fasten the center of the door
jamb to the front wall panel and the
front wall channel with two screws.
Front Wall Channel
Cross-Section
Top View
Front Wall Channel
Acorn Nut
Screw
STEP
Screw
9369
T
ON
FR
3
TOP VIEW
Door Track
4 Fasten the top of the door jamb to
Screw
Screw
the door track with two screws. Do
the same for the bottom into frame.
Repeat steps 2 through 4 for the
opposite door jamb.
STEP
4
23
● Parts Needed For ●
Step 11
● 8576 Right Gable (2)
● 8577 Left Gable (2)
● 6635 Roof Beam Bracket (4)
Gable Assemblies
SR24
The gables go on top of the front and
rear walls to support the roof beams.
NOTE
The gables are packed nested
together and might be mistaken
as one piece. Carefully separate
them before continuing.
1
Attach the four roof beam
brackets to the gables using two
bolts, washers and nuts.
NOTE
Mounting leg of bracket must
face toward center of gable.
FR
ON
T
8577
6635
Roof Beam Brackets
8576
Washer
STEP
1
24
6635
Roof Beam Brackets
● Left Gable Assemblies (2)
● Right Gable Assemblies (2)
● 9009 Gable Brace (2)
● Parts Needed For ●
Step 12
Gables/Braces
SR25
1
Lift and fasten a right and left
gable, under angle at corner, to the
door track and rear wall angle with
screws.
Hint: On the front gable, leave out 2
screws closest to center gable leg.
On the rear gable, use a bolt and nut
at the overlapping rear wall angle.
2
Join the left and right gables
together with a gable brace using a
bolt and nut in the second hole from
the bottom only.
Repeat Steps 1 & 2 for the opposite
side of building.
STEP
3 Fasten the track supports to the
1
Gable
front gable assembly only as shown.
9009 Gable Brace
STEP
2
Track Supports 6228
STEP
3
25
Step 13
● Parts Needed For ●
Roof Beam//Braces
● Main Roof Beam Assembly (1)
● Single Roof Beam Assemblies (2)
● 9204 Roof Beam Brace (2)
SP26
1 Wrap the weather stripping tape
STEP
around the two joined edges of the
large left and right gables. See diagram. Cut the weather stripping to
length and repeat on next gable set.
1
2 Spread the two halves of the double
Weather Stripping
roof beam and fasten to the gable
brace of the front gable.
Spread Two Halves
Of Roof Beams
3 Fasten the other end of the double
STEP
2
roof beam to the gable brace of the
rear gable.
4
STEP
Fasten the single roof beams,
small holes on top, as shown using
bolts and nuts.
3
Roof Beam (Double)
5 Fasten a roof beam brace to the
double roof beam behind the front
gable by placing the tab on the end of
the brace between the roof beams.
Align the tab with the fourth hole and
fasten the brace with a bolt and nut.
STEP
4
6
Roof Beam (Single)
Fasten the lower end of the roof
beam brace to the track support with
a bolt and nut.
7
Fasten a roof beam brace between the rear gable and the roof
beam at the third hole, as shown.
STEP
5
Roof Beam Brace 9204
Roof Beam Brace 9204
STEP
STEP
6
26
7
● Parts Needed For ●
Step 14
● 9984 Right Roof Panel (1)
Right Roof Panel
SP27
Installing the roof panels is best done
with a step ladder. Install the first roof
panel at the back right corner of the
building. Each screw and bolt in the
roof requires a washer.
NOTE
Measure the building diagonally
again and make adjustments to
make sure the building is square
and level. This will make the roof
panels fit better, and holes will
align. Don't anchor the floor frame.
9984
(6) Screws
STEP
1
NOTE
If a Roof Beef-Up Kit was
purchased, assemble prior to
attaching the roof panels.
STEP
2
Nut
Washer
1 Locate the roof panels and find the
2 Position the right roof panel at the
Gable
right roof panel part number 9984.
9984 Right Roof Panel
back right corner and fasten to the
gable with six bolts and nuts and roof
beams using six screws. Do not fasten the lower end of the panel to the
side wall angle at this time.
Bolt
(6)
1
2
3
4
5
6
(3)
Screws
FRO
NT
27
Step 15
● Parts Needed For ●
● 9983 Left Roof Panel (1)
● 7743 Roof Panel (2)
● 6797 Ridge Cap (1)
Ridge Cap & Panels
SP28
1 Install a left roof panel 9983 at the
Screws To
Roof Beam
left rear corner of the roof.
2
Cover the joint at the peak with
weather stripping tape. Unroll the
tape and press it down over the opening at the ridge as you install each
roof panel. Do not cut the tape at this
time.
Fasten at
Overlap With
Bolt
Fasten At
Overlap With
Bolt
Screws To
Roof Beam
3 Install two roof panels 7743 working side to side. Do not fasten the
lower end of the panels to the side
wall angles at this time. Continue
weather stripping the ridge opening.
Do not fasten
at this time
NOTE
Narrow roof panel crimped rib is
overlapped by wide rib of
adjacent panel where possible
4 Install the first ridge cap 6797 on
the completed roof section using bolts
and nuts. Do not fasten the ends of
the ridge cap at this time.
5
Fasten the roof panel ribs, peak
cap and ridge cap together using
bolts and nuts.
STEP
STEP
4
5
6797
STEP
1
Weather
Stripping
Tape
9983 Left Roof Panel
7743
STEP
2
7743
Roof Panel
STEP
3
28
● Parts Needed For ●
Step 16
Ridge Cap & Panels
● 7743 Roof Panel (4)
● 6869 Ridge Cap (1)
SP29
1 Install the second ridge cap 6869
overlapping the first ridge cap while
installing four roof panels 7743. Hint:
The bolts on the ridge cap need to be
left loose to move the ridge cap to the
side and overlap the ribs of the next
roof panel. Continue weather stripping the ridge.
NOTE
If roof beam holes do not line up
with the roof panel holes, shift the
building from left to right.
If this does not help, your building
may not be level. Shim the
corners until holes line up.
6869
Weather Stripping Tape
7743 Roof Panel
7743 Roof Panel
29
● Parts Needed For ●
Step 17
Ridge Cap & Panels
SP30
1
Install the third ridge cap 6797
overlapping the second ridge cap
while installing the remaining two
roof panels 7743. Hint: The bolts on
the ridge cap need to be left loose to
move the ridge cap to the side and
overlap the ribs of the next roof panel.
Continue weather stripping the ridge.
2 Install the left 9983 and right roof
panel 9984 as you unroll the weather
stripping tape, and press it down.
Fasten the lower end of the panels to
the side wall angles using screws
and washers.
3
Fasten the roof panel ribs, peak
cap and ridge cap together using
bolts and nuts.
STEP
STEP
2
6797
1
7743
9984
7743
9983
Peak Cap
Cut
Weather Stripping
and Fold Under
STEP
3
STEP
2
30
● 6797 Ridge Cap (1)
● 7743 Roof Panel (2)
● 9983 Left Roof Panel (1)
● 9984 Right Roof Panel (1)
● Parts Needed For ●
Step 18
Roof Trim
● 6893 Left Side Roof Trim (2)
● 6015 Side Roof Trim (2)
● 6892 Right Side Roof Trim (2)
SP31
1 Attach the right, left and side roof
trim pieces to the lower end of the
roof panels on each side of the building using screws at each panel overlap.
NOTE
A single screw fastens both trim
pieces at the overlap.
2
Using your thumb and index finger, overbend the bottom flange of
the roof panel rib at the corner
inward enough so the right and left
roof trim caps fit onto right and left
corners.
3
Fasten the roof trim caps to the
side trim using a screw.
6893
STEP
3
Roof Trim Cap
6015
6892
6892
Roof Trim
6015 STEP
6893
1
STEP
2
Tuck Flange
Inward to Fit
Inside of
Roof Trim Cap
31
Step 19
● 3719 Door Handle Brace (2)
● 10475 Right and Left Doors (2)
● 10497 Horizontal Door Brace (4)
● 6278 Vertical Door Brace (2)
● Parts Needed For ●
Door Assembly
SO32
The steps on this page tell how to
assemble the right door. You will
perform exactly the same procedures
for the left door. Each bolt and screw
in the door requires a washer. Proceed as follows:
66045
1 Attach the door handle brace and
10497
6278
66045
3719
handle to the door with 1 bolt as
shown. Don't tighten the bolt yet.
3719
2 Swing the door handle brace up to
the hole on the center of the door and
insert a screw.
66382
66382
3
Hold the vertical door brace
against the center of the inside surface of the door and turn the screw to
hold the vertical door brace and door
handle brace in place. Fasten to
door above and below center
connection using 2 screws.
4
Insert a second bolt in the door
handle and tighten both bolts.
STEP
10475 Right Door
10475 Left Door
1
10497
6278
5 Put a horizontal door brace onto
the top edge and bottom edge and
fasten with 1 bolt in the center.
STEP
4
6 Attach the lower door guides and
bolts as shown.
7
Repeat steps 1 through 6 for the
left door.
STEP
STEP
2
3
STEP
5
10497
END VIEW
SHOWING:
Horizontal
Door Brace
Door
Washer
STEP
6
32
66382
Guide
Step 20
● Parts Needed For ●
● Right Door Assembly (1)
● Left Door Assembly (1)
Door Installation & Adjustment
SQ33
Gable
Horizontal Door Brace
Door Track
Door Slide
1
Door
From inside the building, put the
bottom of the right door assembly (on
your left when you are inside the
building) behind door jamb into the
front frame track.
STEP
STEP
1
2
2 Position the top of the door so that
the holes in the door line up with the
holes in the door slides.
Front Floor Frame Assembly
3 Fasten the door to the door slides
Door Slide
using two #10Bx1/2" screws per door
slide.
NOTE
The holes in the door slides allow
you to adjust the doors. Place the
door in the middle holes.
#10Bx1/2" Screw
Adjustment Holes
STEP
4 Repeat steps 1 through 3 for the
3
left door.
Adjustment Holes Allow
Doors to Meet Evenly
Along Their Length
Right Door
Left Door
STEP
4
Keep this Owner's Manual and Assembly Instructions for future reference.
33
SOME FACTS ABOUT RUST
SO34
SOME FACTS ABOUT RUST
Rusting is a natural oxidizing process that occurs
when bare metal is exposed to moisture. Problem
areas include screw holes, unfinished edges, or
where scrapes and nicks occur in the protective
coating through normal assembly, handling and
use. Identifying these natural rusting problem areas
and taking some simple rust protection precautions
can help to stop rust from developing, or stop it
quickly as soon as it appears.
1. Avoid nicking or scraping the coating surface,
inside and out.
2. Use all the washers supplied. In addition to protecting against weather infiltration, the washers protect the metal from being scraped by the screws.
3. Keep roof, base perimeter and door tracks free of
debris and leaves which may accumulate and retain
moisture. These can do double damage since they
give off acid as they decay.
4. Touch up scrapes or nicks and any area of visible
rust as soon as possible. Make sure the surface is
free of moisture, oils, dirt or grime and then apply an
even film of high quality touch-up paint.
34
CM1014-A1
OB1014-C1
697.68103-C1
697.68104
SP36
714740408