Ask Proxima AV 9320 Projector User Manual

6654_C170_UG.QXD 4/20/04 3:11 PM Page 1
>>>>>>>
InFocus Corporation
27700B SW Parkway Avenue
Wilsonville, Oregon 97070-9215
1-800-294-6400 • 503-685-8888
Fax: 503-685-8887
http://www.infocus.com
In Europe:
InFocus International B.V.
Strawinskylaan 585
1077 XX Amsterdam,The Netherlands
Phone: +31 20 579 2000
Fax: +31 20 579 2999
In Asia:
InFocus Systems Asia Pte Ltd.
238A Thomson Road
#18-01/04 Novena Square
Singapore 307684
Telephone: (65) 6334-9005
Fax: (65) 6333-4525
User’s
Guide
6653_LP600_UG.qxd 4/2/04 2:14 PM Page 2
WARNING: The power cord and cables associated
with this product contain lead, a chemical
known to the state of California to cause birth
defects or other reproductive harm. Wash
hands after handling.
WARNING: This product has a lamp which
contains a very small amount of mercury.
Dispose of it as required by local, state, or
federal ordinances and regulations. For more
information, see www.eiae.org
qÜáë=ÉåíáêÉ=ìëÉêÛë=ÖìáÇÉ=áë=~î~áä~ÄäÉ=çå=íÜÉ=ÉåÅäçëÉÇ=`a=~ë=~å=^ÇçÄÉ=^ÅêçÄ~í=éÇÑ=ÑáäÉ=áå=íÜÉ=ÑçääçïáåÖ=ä~åÖì~ÖÉëW=aìíÅÜI=båÖäáëÜI=cêÉåÅÜI=dÉêã~åI=fí~äá~åI=kçêïÉÖá~åI=
mçêíìÖìÉëÉI=pé~åáëÜI=oìëëá~åI=g~é~åÉëÉI=hçêÉ~åI=qê~Çáíáçå~ä=`ÜáåÉëÉI=páãéäáÑáÉÇ=`ÜáåÉëÉK=_ÉÑçêÉ=ìëáåÖ=íÜáë=éêçàÉÅíçêI=éäÉ~ëÉ=êÉ~Ç=íÜÉëÉ=áåëíêìÅíáçåëK=
aÉòÉ=Ü~åÇäÉáÇáåÖ=áë=áå=òáàå=ÖÉÜÉÉä=ÄÉëÅÜáâÄ~~ê=çé=ÇÉ=ÄáàÖÉîçÉÖÇÉ=ÅÇ=áå=ÇÉ=îçêã=î~å=ÉÉå=éÇÑJÄÉëí~åÇ=E^ÇçÄÉ=^ÅêçÄ~íFI=Éå=ïÉä=áå=ÇÉ=îçäÖÉåÇÉ=í~äÉåW=båÖÉäëI=cê~åëI=
aìáíëI=fí~äá~~åëI=kççêëI=mçêíìÖÉÉëI=pé~~åëI=kÉÇÉêä~åÇëI=oìëëáëÅÜI=g~é~åëI=hçêÉ~~åëI=íê~ÇáíáçåÉÉä=`ÜáåÉÉëI=îÉêÉÉåîçìÇáÖÇ=`ÜáåÉÉëK=iÉÉë=çåÇÉêëí~~åÇÉ=áåëíêìÅíáÉë=
îççêÇ~í=ì=ÇÉòÉ=éêçàÉÅíçê=ÖÉÄêìáâíK
iÉ=ãçÇÉ=ÇDÉãéäçá=ÅçãéäÉí=Éëí=ÇáëéçåáÄäÉ=ëìê=äÉ=`a=àçáåí=ëçìë=ÑçêãÉ=ÇÉ=ÑáÅÜáÉê=éÇÑ=ÇD^ÇçÄÉ=^ÅêçÄ~í=Ç~åë=äÉë=ä~åÖìÉë=ëìáî~åíÉë=W=Üçää~åÇ~áëI=~åÖä~áëI=Ñê~å´~áëI=
~ääÉã~åÇI=áí~äáÉåI=åçêî¨ÖáÉåI=éçêíìÖ~áëI=Éëé~ÖåçäI=êìëëÉI=à~éçå~áëI=Åçê¨ÉåI=ÅÜáåçáë=íê~ÇáíáçååÉäI=ÅÜáåçáë=ëáãéäáÑá¨K=^î~åí=ÇDìíáäáëÉê=ÅÉ=éêçàÉÅíÉìêI=îÉìáääÉò=äáêÉ=
ÅÉë=áåëíêìÅíáçåëK=
aáÉ=îçääëí®åÇáÖÉ=_ÉåìíòÉê~åäÉáíìåÖ=áëí=~ìÑ=ÇÉê=áã=iáÉÑÉêìãÑ~åÖ=ÉåíÜ~äíÉåÉå=`a=~äë=^ÇçÄÉ=^ÅêçÄ~í=macJa~íÉá=áå=ÇÉå=ÑçäÖÉåÇÉå=péê~ÅÜÉå=îÉêÑΩÖÄ~êW=káÉÇÉêä®åÇáëÅÜI=
båÖäáëÅÜI=cê~åò∏ëáëÅÜI=aÉìíëÅÜI=fí~äáÉåáëÅÜI=kçêïÉÖáëÅÜI=mçêíìÖáÉëáëÅÜI=pé~åáëÅÜI=oìëëáëÅÜI=g~é~åáëÅÜI=hçêÉ~åáëÅÜI=qê~ÇáíáçåÉääÉë=`ÜáåÉëáëÅÜ=ìåÇ=sÉêÉáåÑ~ÅÜíÉë=`ÜáåÉJ
ëáëÅÜK=_áííÉ=äÉëÉå=páÉ=ÇáÉëÉ=^åïÉáëìåÖÉå=îçê=ÇÉê=sÉêïÉåÇìåÖ=ÇÉë=mêçàÉâíçêëK=
i~=éêÉëÉåíÉ=ÖìáÇ~=≠=ÇáëéçåáÄáäÉ=ëìä=`a=~ääÉÖ~íçI=ÅçãÉ=ÑáäÉ=^ÇçÄÉ=^ÅêçÄ~í=éÇÑI=åÉääÉ=ëÉÖìÉåíá=äáåÖìÉW=çä~åÇÉëÉI=áåÖäÉëÉI=Ñê~åÅÉëÉI=íÉÇÉëÅçI=áí~äá~åçI=åçêîÉÖÉëÉI=
éçêíçÖÜÉëÉI=ëé~ÖåçäçI=êìëëçI=Öá~ééçåÉëÉI=ÅçêÉ~åçI=ÅáåÉëÉ=íê~Çáòáçå~äÉ=É=ÅáåÉëÉ=ëÉãéäáÑáÅ~íçK=mêáã~=Çá=ìë~êÉ=èìÉëíç=éêçáÉííçêÉI=äÉÖÖÉêÉ=äÉ=ëÉÖìÉåíá=áëíêìòáçåáK=
eÉäÉ=ÇÉååÉ=ÄêìâÉêÜ™åÇÄçâÉå=ÑáååÉë=é™=ÇÉå=îÉÇä~ÖíÉ=`aJÉå=ëçã=Éå=^ÇçÄÉ=^ÅêçÄ~í=éÇÑJÑáä=é™=Ñ›äÖÉåÇÉ=ëéê™âW=kÉÇÉêä~åÇëâI=ÉåÖÉäëâI=Ñê~åëâI=íóëâI=áí~äáÉåëâI=åçêëâI=
éçêíìÖáëáëâI=ëé~åëâI=êìëëáëâI=à~é~åëâI=âçêÉ~åëâI=íê~ÇáëàçåÉää=çÖ=ÑçêÉåâäÉí=âáåÉëáëâK=iÉë=Çáëë=~åîáëåáåÖÉåÉ=Ñ›ê=éêçàÉâíçêÉå=í~ë=á=ÄêìâK=
bëíÉ=Öìá~=Çç=ìëì•êáç=ÅçãéäÉíç=Éëí•=Çáëéçå∞îÉä=åç=`a=~åÉñçI=Åçãç=ìã=~êèìáîç=éÇÑ=Çç=^ÇçÄÉ=^ÅêçÄ~í=åçë=ëÉÖìáåíÉë=áÇáçã~ëW=Üçä~åÇÆëI=áåÖäÆëI=Ñê~åÅÆëI=~äÉã©çI=
áí~äá~åçI=åçêìÉÖìÆëI=éçêíìÖìÆëI=Éëé~åÜçäI=êìëëçI=à~éçåÆëI=ÅçêÉ~åçI=ÅÜáåÆë=íê~ÇáÅáçå~äI=ÅÜáåÆë=ëáãéäáÑáÅ~ÇçK=^åíÉë=ÇÉ=ìíáäáò~ê=ÉëíÉ=éêçàÉíçêI=äÉá~=Éëí~ë=áåëíêì´πÉëK=
bëíÉ=ã~åì~ä=ÇÉ=ìëç=Éëí•=ÇáëéçåáÄäÉ=Éå=ëì=íçí~äáÇ~Ç=Éå=Éä=`a=áåÅäìáÇçI=Åçãç=~êÅÜáîç=éÇÑ=ÇÉ=^ÇçÄÉ=^ÅêçÄ~íI=Éå=äçë=ëáÖìáÉåíÉë=áÇáçã~ëW=Üçä~åǨëI=áåÖä¨ëI=Ñê~åÅÉëI=
~äÉã•åI=áí~äá~åçI=åçêìÉÖçI=éçêíìÖìÆëI=Éëé~¥çäI=êìëçI=à~éçå¨ëI=ÅçêÉ~åçI=ÅÜáåç=íê~ÇáÅáçå~äI=ÅÜáåç=ëáãéäáÑáÅ~ÇçK=^åíÉë=ÇÉ=ìë~ê=Éä=éêçóÉÅíçêI=äÉ~=Éëí~ë=áåëíêìÅÅáçåÉëK
Данное руководство пользователя в полном объеме представлено на прилагаемом компакт-диске в виде pdf-файла Adobe Acrobat на следующих языках:
английском, голландском, французском, немецком, итальянском, норвежском, португальском, испанском, русском, японском, корейском, традиционном и
упрощенном китайском. Перед использованием проектора, прочитайте данные инструкции.
このユーザーズ=ガイドは、プロジェクタに付属している `a に ^ÇçÄÉ=^ÅêçÄ~í の mac ファイル形式として収録されています。次の言語のユーザーズ=ガイドをご利用いただ
けます。オランダ語、英語、フランス語、ドイツ語、イタリア語、ノルウェー語、ポルトガル語、スペイン語、ロシア語、日本語、韓国語、簡体中国語、繁体中国語。この
プロジェクタを使用する前に、ユーザーズ=ガイドを必ずお読みください。
동봉된 CD 에는 Adobe Acrobat PDF 파일 형식의 사용 설명서가 : 네델란드어 , 영어 , 프랑스어 , 독일어 , 이탈리아어 , 노르웨이어 , 포르투갈어 , 스페인어 , 러시아어 ,
일본어 , 한국어 , 중국어 ( 번체 및 간체 ) 로 제공됩니다 . 프로젝터를 사용하기 전에 다음 지침을 읽으십시오 .
附带的 CD 上有 Adobe Acrobat pdf 格式的整本 《使用者指南》,包括下列各种语言版本:荷兰文、英文、法文、德文、意大利文、挪威文、葡萄牙文、西班牙文、俄文、日文、
韩文、繁体中文、简体中文。请在使用投影仪之前先阅读这些说明。
所附的光碟片上,有 Adobe Acrobat (PDF) 格式的這本 《使用者手冊》;所提供的不同語言版本包括:荷蘭文、英文、法文、德文、意大利文、挪威文、葡萄牙文、西班牙文、
俄文、日文、韓文、繁體中文,以及簡體中文。開始使用本投影機之前,請先詳細閱讀這些說明。
Declaration of Conformity
Canada
Manufacturer: InFocus Corporation, 27700B SW Parkway Ave. Wilsonville, Oregon
97070 USA
European Office: Strawinskylaan 585, 1077 XX Amsterdam, The Netherlands
We declare under our sole responsibility that this projector conforms to the following
directives and norms:
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Agency Approvals
UL, CUL, TUV, GOST
Other specific Country Approvals may apply, please see product certification label.
EMC Directive 89/336/EEC, Amended by 93/68/EEC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
Safety: EN 60950: 2000
May, 2004
This user’s guide applies to models C170 and GEN205.
InFocus reserves the right to alter product offerings and specifications at any time.
Trademarks
Apple, and Macintosh are trademarks or registered trademarks of Apple Computer,
Inc. Microsoft, PowerPoint, Word, Excel and Windows are trademarks or registered
trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems Incorporated. InFocus, ASK Proxima, LiteShow,
LitePort, and LP are trademarks or registered trademarks of InFocus Corporation.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
EN 55022 Warning
This is a Class A product. In a domestic environment it may cause radio interference,
in which case the user may be required to take adequate measures. The typical use is
in a conference room, meeting room or auditorium.
2
If you are experienced in setting up presentation systems, use the included
Quick Set Up card. For complete details on connecting and operating the
projector, refer to this User’s Guide. Electronic versions of this User’s Guide
in multiple languages are available on the included CD and on our website.
The most current versions can be found on our website.
Table of Contents
Introduction
Connecting a computer
Required computer connections
Displaying a computer image
First-time projector use with Windows 98
Adjusting the image
Connecting a video device
Displaying a video image
5
7
7
9
10
12
13
14
Shutting down the projector
16
Troubleshooting your setup
16
Using the keypad buttons
Using the remote control
Using the LitePort player
Using the audio
25
26
27
28
Optimizing computer images
Presentation features
Optimizing video images
Customizing the projector
29
29
29
29
Using the menus
Picture menu
Settings menu
30
31
34
Maintenance
Cleaning the lens
Using the security lock
Replacing the projection lamp
Cleaning the lamp filter screens
39
39
39
40
42
Accessories
Red LED behavior and projector errors
Projected image size
43
43
44
44
Appendix
The website also has technical specifications (an interactive image size calculator, laptop activation commands, connector pin outs, a glossary, the
product data sheet), a web store to buy accessories, and a page for online
registration. See the inside of the back cover for a list of all relevant web
addresses.
3
Important Operating Considerations for Safety
•
Place the projector in a horizontal position no greater than 15 degrees
off axis.
•
Locate the projector in a well-ventilated area without any obstructions
to intake or exhaust vents. Do not place the projector on a tablecloth or
other soft covering that may block the vents.
•
Locate the projector at least 4' (1.2 m) away from any heating or cooling
vents.
•
Use only approved ceiling mounts.
•
Use only the power cord provided. A surge-protected power strip is
recommended.
•
Refer to this manual for proper startup and shutdown procedures.
•
In the unlikely event of the lamp rupturing, discard any edible items
placed in the surrounding area and thoroughly clean the area along all
sides of the projector. Wash hands after cleaning the area and handling
the ruptured lamp. This product has a lamp which contains a very
small amount of mercury. Dispose of it as required by local, state or federal ordinances and regulations. For more information see
www.eiae.org.
Do not place objects or people in the 2 foot (.6m) area along the side of the projector.
For ceiling mount applications, this area should be 5 feet (1.5m).
2 ft (.6m)
Follow these instructions to help ensure image quality and lamp life over
the life of the projector. Failure to follow these instructions may affect the
warranty. For complete details of the warranty, see the Warranty section at
the end of this user's guide.
5 ft (1.5m)
4
Projector components and features
Introduction
keypad
Your new digital projector provides computer and video inputs and has
XGA 1024x768 resolution. The projector is easy to connect, easy to use, and
easy to maintain. An Interactive Display on the top of the projector gives
you constant feedback on the status of the projector.
Online Registration
Register your projector on our website to receive product updates,
announcements, and registration incentives. See the inside of the back cover
for the web address.
speaker
remote
control
receiver (IR)
elevator foot release
Included items
zoom
focus
carry case
Interactive display
projector
remote
lens cap
documentation
lens cap tether*
audio cable
adapter
audio cable
computer
cable
video cable
IR receiver
power
cable
connectors
heat vent
leveling
foot
*The lens cap tether ships in the Documentation Pack. Attach it to the lens cap and
the projector if desired.
5
IR receiver
Connector Panel
Connector panel
The projector provides computer and video connectors:
•
one M1-D/A (HD, DVI, and computer)
•
one VESA (HD, HD component, and computer)
•
one S-video
•
one composite RCA video
•
one audio in/one audio out
M1-D/A
computer
VESA in/
monitor out
composite
video
s-video
RS-232 serial control
USB JPEG
It also has an RS-232 serial connector for serial control. The Command Line
Interface (CLI) specifications and commands are on our website.
lock
audio
power
connector
TM
USB connector (Type A) and player for
The projector also has a LitePort
JPEG (Joint Photographic Experts Group, .jpg, .jpe, or .jpeg) images. This
allows you to display any JPEG image automatically, without a computer
connected. Use your own JPEGs from your digital camera, or convert your
files, such as Microsoft PowerPointTM, WordTM, or ExcelTM files, into
JPEGs using LitePort Utility (included on the CD), which allows you to easily generate the highest quality JPEG images possible. Then transfer the
JPEG images from your computer to the projector using a USB mass storage
device and your images are ready to be displayed. (Please refer to the Service and Support section of our website for advanced specifications on the
USB device and JPEG files.) You can use the remote control to select which
JPEGs to view (page 27) or you can set up the LitePort player using the LitePort onscreen menu to select display preferences and automatically display
and advance your JPEGs (page 36).
Wireless Projection
You can use the projector’s M1 connector along with the InFocus
LiteShow wireless adapter and software for cable-free digital projection.
Contact an authorized InFocus dealer or visit the website listed on the back
inside cover of this User’s Guide for more information.
6
external
speaker
(audio out)
Connecting a computer
connect computer cable
Required computer connections
Connect the black end of the computer cable to the Computer 1 connector
on the projector. Connect the blue end to the video port on your computer. If
you are using a desktop computer, you first need to disconnect the monitor
cable from the computer’s video port.
Some Macintosh computers do not have a standard VESA-out video port.
If the supplied computer cable will not connect to your computer, purchase
the appropriate adapter from your Apple reseller.
Connect the black power cable to the connector on the back of the projector
and to your electrical outlet.
connect power cable
The Power LED on the projector’s keypad turns solid green.
NOTE: Always use the power cable that shipped with the projector.
Optional computer connections
connect computer cable
To advance slides in a PowerPoint™ presentation using the remote, plug the
USB connector on the computer cable into the USB mouse connector on
your computer. USB drivers must be installed to use the USB feature. For
more information, see page 11.
To have sound with your presentation, connect the audio cable to your computer and to the Audio In connector on the projector.
connect audio cable
7
If you are using a desktop computer and want to see the image on your
computer screen as well as on the projection screen, plug the monitor cable
to the black Computer 2 connector on the projector. This connector can be
used as monitor out or VESA in. The default is VESA in, so you must
change this option in the menu to use monitor out. See page 34 to switch
between the two functions.
connect monitor cable
If you prefer connecting your projector to your computer with an optional
VESA cable, connect one end of the cable to the VESA port on your computer, and connect the other end of the cable to the blue Computer 2 connector on the projector.
connect VESA cable
This connector can be used as monitor out or VESA in. The default is VESA
in.
You can control the projector from an LCD control panel or computer by
connecting an RS-232 cable to the projector’s Serial Control connector. Specific RS-232 commands can be found in the Service and Support section of
our website.
connect RS-232 cable
You can play JPEGs using the LitePort USB connector and LitePort player.
You need a USB mass storage device to use this connector. See page 27 for
details.
connect USB mass storage device
8
Displaying a computer image
Remove the lens cap.
remove lens cap
Press the Power button on the top of the projector or the remote.
press Power button
The LED flashes green and the fans start to run. When the lamp comes on,
the startup screen is displayed and the LED is steady green. It can take a
minute for the image to achieve full brightness. The Interactive Display on
the projector indicates the startup status.
? No startup screen? Get help on page 17.
turn on computer
Turn on your computer.
The computer’s image should appear on the projection screen. If it doesn’t,
press the Source button on the projector’s keypad.
Make sure your laptop’s external video port is active.
activate laptop’s external port
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F8 or CRT/LCD
key turns the external display on and off. Locate a function key labeled
CRT/LCD or a function key with a monitor symbol. Press FN and the
labeled function key simultaneously. Refer to your laptop’s documentation to learn your laptop’s key combination.
? No computer image? Try pressing the Auto Image
button on the keypad. Get help on page 17.
9
a
First-time projector use with Windows 98
If you are running Windows 2000, Windows ME, or Window XP, skip these
steps and go to “Adjusting the image” on page 12.
The first time you connect a computer running Windows 98 to the projector,
the computer recognizes the projector as “new hardware” and the Add
New Hardware Wizard appears. Follow these instructions to use the Wizard to load the correct driver (which was installed with your Windows
operating system).
b
a Click Next to begin searching for the driver.
b Make sure “Search for the best driver” is selected, then click Next.
c
c Uncheck any checked boxes, then click Next. Windows automatically
locates the driver. If this driver has been removed, reload the driver using
your Windows operating system CD.
d
d When Windows finds the driver, you are ready to install it. Click Next.
10
Skip this page if you did not connect the USB portion of the M1 computer cable
For Windows 98:
•
If you connected the USB cable, the Add New Hardware Wizard
appears again. Drivers must be installed to use the USB functionality.
•
The Wizard launches two times.
The first time it detects a USB Human Interface Device (for the keyboard).
The second time it detects a USB Human Interface Device (for the
mouse).
For Windows 2000, Windows ME, and Windows XP:
•
The USB drivers are automatically installed.
11
Adjusting the image
release button
adjust height
Adjust the height of the projector, if necessary, by pressing the release button to extend the elevator foot.
Rotate the leveling foot (located at the bottom back right corner), if necessary.
elevator
foot
Position the projector the desired distance from the screen at a 90 degree
angle to the screen.
rotate
leveling
foot
adjust distance
See page 44 for a table listing screen sizes and distances.
Adjust the zoom or focus rings by rotating them until the desired image size
and focus are produced.
adjust zoom and focus
zoom
focus
The projector has an Auto Keystone option that is turned on by default. But
if the image is not square, adjust the vertical digital keystone by using the
buttons on the keypad. Press the upper Keystone button to reduce the
upper part of the image, and press the lower Keystone button to reduce the
lower part.
You can also adjust the keystone via the menus, or turn off Auto Keystone.
See page 31.
adjust keystone
adjust Contrast or Brightness
Adjust the Contrast or Brightness in the Picture menu.
contrast
See page 30 for help with the menus.
brightness
12
Connecting a video device
connect video and audio cables
Standard video connections
Plug the video cable into the video-out connector on the video device. Plug
the other yellow connector into the yellow Video 2 connector on the projector.
Plug the white connector of the audio adapter into the left audio out connector on the video device and plug the red connector into the right audio
out connector on the video device.
Plug the audio cable into the other end of the audio cable adapter and into
the audio in connector on the projector.
connect power cable
Connect the black power cable to the connector on the back of the projector
and to your electrical outlet.
NOTE: Always use the power cable that shipped with the projector.
connect S-video and audio cables
Optional video connections
If the video device uses a round, four-prong S-video connector, plug an
S-video cable (sold separately) into the S-video connector on the video
device and into the S-Video 1 connector on the projector. Use the audio connectors as described directly above.
To connect a progressive scan EDTV or HD source, use the Component to
M1 adapter (sold separately).
13
Displaying a video image
remove lens cap
Remove the lens cap.
press Power button
Press the Power button on the top of the projector or the remote.
The LED flashes green and the fans start to run. When the lamp comes on,
the startup screen is displayed and the LED is steady green. It can take a
minute for the image to achieve full brightness. The Interactive Display on
the projector indicates the startup status.
? No startup screen? Get help on page 16.
Plug in and turn on the video device.
turn on video device
The video device’s image should appear on the projection screen. If it
doesn’t, press the Source button on the keypad.
release button
Adjust the height of the projector by pressing the release button to extend
the elevator foot. Rotate the leveling foot, if necessary.
adjust height
elevator
foot
Position the projector the desired distance from the screen at a 90 degree
angle to the screen. See page 44 for a table listing screen sizes and distances
to the screen.
adjust distance
14
rotate
leveling
foot
Adjust the zoom or focus rings by rotating them until the desired image size
and focus are produced.
adjust zoom and focus
zoom
focus
If the image is not square, adjust the vertical keystone using the buttons on
the keypad.
Press the upper Keystone button to reduce the upper part of the image, and
press the lower Keystone button to reduce the lower part.
You can also adjust the keystone via the menus, or set the projector to automatically adjust the keystone. See page 31.
adjust keystone
Adjust the volume on the keypad or remote.
adjust volume
Adjust the Contrast, Brightness, Color, or Tint in the Picture menu.
adjust Picture menu
See page 30 for help with the menus.
15
Shutting down the projector
Troubleshooting your setup
The projector automatically blanks the screen after no active source is
detected for 30 minutes. This blank screen helps preserve the life of the projector. The image returns when an active source is detected or a remote or
keypad button is pressed. The Interactive Display on the projector indicates
the shutdown status.
If your image appears correctly on the screen, skip to the next section
(page 26). If it does not, troubleshoot the setup. The Interactive Display and
LED on top of the projector indicate the state of the projector and can help
you troubleshoot.
Screen Save
Table 1: LED behavior and meaning
You can make the blank screen appear after five minutes by turning on
Screen Save in the Settings>System menu. See page 35. There are six time
options for the Screen Save feature. They range from five minutes to 30 minutes with five minute intervals.
LED color/behavior
Meaning
solid green
The projector is plugged in, or the projector has been powered on and the software has initialized. The projector has
been turned off and the fans have stopped.
blinking green
The power button has been pressed and
the software is initializing, or the projector is powering down and the fans are
running to cool the lamp.
blinking red
A fan or lamp failure has occurred. Make
sure the vents aren’t blocked (see
page 23). Turn off the projector and wait
one minute, then turn the projector on
again. If the Replace Lamp message
appears, replace the lamp and reset the
lamp timer. Contact Technical Support if
the problem persists.
Power Save
The projector also has a Power Save feature that automatically turns the
lamp off after no signal is detected for 20 minutes. After 10 additional minutes with no signal, the projector powers down. If an active signal is
received before the projector powers down, the image is displayed. You
must press the Power button to display an image after 30 minutes have
passed. When Power Save is enabled, Screen Save is disabled. See page 35.
Turning off the projector
To turn off the projector, press the Power button and verify that you want to
turn the projector off by pressing the Power button again within 3 seconds.
You can cancel the shutdown by not pressing the Power button a second
time. The lamp turns off and the LED blinks green for 1 minute while the
fans continue to run to cool the lamp. When the lamp has cooled, the LED
lights green and the fans stop. Unplug the power cable to completely power
off the projector.
see page 44 for more information
solid red
An unidentifiable error: please contact
Technical Support.
The following tables show common problems. In some cases, more than one
possible solution is provided. Try the solutions in the order they are presented. When the problem is solved, you can skip the additional solutions.
16
Source Troubleshooting
Problem
Solution
Result
No startup screen
Plug power cable in, press Power button.
Remove lens cap.
Correct image
Computer image projected
Only startup screen appears
Press the Source button
Activate laptop’s external port
A
A
or restart
laptop
17
A
No computer image, just the words “Signal out of
range”
Adjust computer refresh rate in Control
Panel>Display>Settings>Advanced>
Adapter (location varies by operating
system)
Computer image projected
Signal
ou
range t of
A
A
A
You may also need to set a different
resolution on your computer, as shown
in the following problem, “Image fuzzy
or cropped”
For PC: Image fuzzy or cropped
AA
A
Set your computer’s display resolution to
the native resolution of the projector
(Start>Settings>Control
Panel>Display>Settings tab, select
1024x768)
For a laptop,
disable laptop
monitor
or turn-on dualdisplay mode
18
Image clear and not cropped
A
For Macintosh: Image fuzzy or cropped
AA
Set your computer’s display resolution to
the native resolution of the projector
(Apple menu>System
Preferences>Displays, choose 1024x768)
A
Only my laptop’s background appears, not the
Desktop icons
A
Disable “Extend my Windows Desktop” in
Control Panel>Display>Settings>Display 2
(location varies by operating system)
A
Image clear and not cropped
A
Background and Desktop projected
A
Uncheck this
option, then
click Apply
19
A
The video embedded in my PowerPoint
presentation does not play on the screen
A
Turn off the internal LCD display on your
laptop
A
A
B
Remote control not advancing PowerPoint slides
Embedded video plays correctly
Connect USB cable (page 7) then load USB
drivers, if needed (page 10).
X
20
B
Remote advances slides
See page 26 for information on the remote
Projector troubleshooting
Problem
Solution
Result
Image not square
Adjust keystone on keypad or Picture menu
Square image
Image not sharp
Adjust the focus lens or Sharpness in the
Picture>Advanced menu
Correct image
AB
AB
Image does not fit 16:9 screen
Change aspect ratio to 16:9 in
Picture>Aspect ratio menu
21
Correct image
Turn off Auto Ceiling or Ceiling in
Settings>System menu
Image upside down
BA
Image reversed left to right
AB
Turn off Rear in Settings>System menu
A
Projected colors don’t match source
Correct image
Correct image
AB
Adjust color, tint, color temperature,
brightness, contrast in the menus
COLOR
Correct image
COLOR
22
Image not centered on screen
Move projector, adjust zoom, adjust height
Correct image
zoom
Adjust horizontal or vertical position in
Picture>Advanced menu
Lamp won’t turn on, LED blinking red (page 16)
Make sure vents aren’t blocked; allow
projector to cool for one minute
blinks
red
23
Unplug projector; wait one minute; plug in
projector and turn it on: lamp lights
Lamp won’t turn on, LED blinking red (page 16)
Lamp must be replaced (page 40)
blinks
red
Still having problems?
If you need assistance, visit the Service and Support section of our website
or call us. See the inside of the back cover for a list of all relevant web
addresses.
This product is backed by a limited warranty. An extended warranty plan
may be purchased from your dealer. When sending the projector in for
repair, we recommend shipping the unit in its original packing material, or
having a professional packaging company pack the unit. Please insure your
shipment for its full value.
24
Lamp turns on
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an overview of their functions:
power–turns the projector on (page 9) and off (page 16).
menu–opens the on-screen menus (page 30).
select–confirms choices made in the menus (page 30).
up/down arrows–navigates to and adjusts settings in the menus (page 30).
auto image–resets the projector to the source.
presets–cycles through the available preset settings (page 32).
keystone–vertical keystone adjusts the squareness of the image (page 12).
You can also adjust the keystone via the menus. See page 31.
volume–adjusts sound (page 28).
source–changes the active source.
menu navigation buttons
25
Using the remote control
The remote uses two (2) provided AA batteries. They are easily installed by
sliding the cover off the remote’s back, aligning the + and - ends of the batteries, sliding them into place, and then replacing the cover.
previous button
next button
To operate, point the remote at the projection screen or at the projector (not
at the computer). The range of optimum operation is about 30 feet (9.14m).
Previous and Next buttons allow you to navigate through your PowerPoint
presentation while in Slide Show mode. Connect the USB connector on the
computer cable to your computer to use these buttons. When you do this for
the first time, the Add New Hardware wizard may appear. See page 10 for
details on loading the correct USB drivers.
navigation
buttons
Press the remote’s Menu button to open the projector’s menu system. Use
the arrow buttons to navigate, and the Select button to select features and
adjust values in the menus. See page 30 for more info on the menus.
The remote also has a Power button to turn the projector on and off (see
page 16 for shutdown info), Volume and Mute buttons to control the sound,
and a Source button to switch between sources.
Two presentation-specific features are also provided. Use the Blank button
to display a blank screen instead of the current slide (you can choose which
color is displayed, see page 37); use the Effect button to invoke a user-definable action, such as freeze or aspect ratio (see page 38 to learn to program
this button).
Troubleshooting the remote
26
•
Make sure the batteries are installed in the proper orientation and are
not dead. The LED at the top of the remote lights when any button is
pressed when the battery power is adequate.
•
Make sure you’re pointing the remote at the projector, not the computer, and are within the remote range of 30 feet (9.14m).
•
If you are trying to advance PowerPoint slides, make sure the USB portion of the M1 computer cable is connected and the correct drivers are
installed.
thumbnail on the screen and pressing Next or Down arrow. You are looped
back to Folder 1 when you reach the end of the folder list.
Using the LitePort player
LitePort allows you to display any JPEG image automatically, without a
computer connected. Use your own JPEGs from your digital camera, or convert your files, such as PowerPoint or Word files, into JPEGs using LitePort
Utility (included on the CD). LitePort Utility allows you to easily generate
the highest quality JPEG images possible. (LitePort player is optimized to
display images at 960x720 resolution, so for best results, create JPEGs at this
resolution). Then transfer the JPEG images from your computer to the projector using a USB mass storage device and your images are ready to be displayed. You can use the remote control to select which JPEGs to view or you
can set up the LitePort player using the LitePort onscreen menu to select
display preferences and automatically display and advance your JPEGs. See
page 36.
When active, the player can be in one of three modes:
•
Folder View mode, which shows a thumbnail image representing each
folder that contains a valid JPEG. The thumbnail for that folder is the
first JPEG alphabetically in that folder. Folders are sorted alphabetically
based on the name of the actual directory with no regard to the file system path to the folder.
•
File View mode, which shows a thumbnail of the valid JPEGs in that
folder.
•
Full Screen mode, which shows the first JPEG in the selected folder.
Table 2: Folder View navigation
Folder 1
2
3
4
5
6
7
8
Folder 9 (press Next to
access Folder 10)
In File View mode, pressing Next (or Down) places the selection box around
the next JPEG file, pressing Previous (or Up) places the selection box around
the previous JPEG, pressing Select selects the current JPEG and enters Full
Screen mode, or, if the “return to folders” arrow is highlighted, returns to
Folder View mode. Eight file thumbnails can be displayed on the screen at a
time. If your folder contains more than 8 folders, you can navigate to them
by navigating to the last thumbnail on the screen and pressing Next. You are
looped back to File 1 when you reach the end of the file list.
Table 3: File View navigation
The remote and keypad buttons interact with the player differently in each
mode. When you insert a USB device in the LitePort connector, the player
enters Full Screen mode if Auto Play is checked (the default setting) and the
AutoPlay folder contains a JPEG or it enters Folder View if Auto Play is not
checked. The AutoPlay folder is automatically created by LitePort Utility.
See its online help for details.
In Folder View mode, pressing the Next button (or the Down arrow) places
the white selection box around the next folder, pressing the Previous button
(or the Up arrow) places the selection box around the previous folder, pressing Select selects the current folder and enters File View mode. Nine folder
thumbnails can be displayed on the screen at a time. If your USB drive contains more than 9 folders, you can navigate to them by navigating to the last
Return to
Folders arrow
File 1
2
3
4
5
6
7
File 8 (press Next
to access File 9)
In Full Screen mode, pressing Next (or Down) advances to the next JPEG
file, pressing Previous (or Up) goes to the previous JPEG file, pressing Select
returns File View mode. To rotate the JPEG 90 degrees clockwise, select LitePort Rotate in the Effect menu (see page 38) then press the Effect button.
Press Select to return to File View mode.
27
Using the audio
connect audio cable
To play sound from the projector, connect your source to the Audio In connector on the projector.
To adjust the volume, use the buttons on the keypad or remote.
To adjust the balance or turn off the projector’s chime, use the Audio menu
(see page 34).
To mute the sound, press the Mute button on the remote.
adjust volume
Troubleshooting audio
If there is no sound, check the following:
•
Make sure the audio cable is connected.
•
Make sure mute isn’t active.
•
Make sure the volume is turned up enough. Press the Volume button
on the keypad or remote.
•
Adjust the audio source.
•
If playing a video, make sure the playback has not been paused.
Connecting external speakers
The projector can be attached to external speakers that have their own
power source by plugging a speaker cable into the projector’s Audio Out
connector.
external speakers
speaker
cable
28
Optimizing computer images
Optimizing video images
After your computer is connected properly and the computer’s image is on
the screen, you can optimize the image using the onscreen menus. For general information on using the menus, see page 30.
After the video device is connected properly and the image is on the screen,
you can optimize the image using the onscreen menus. For general information on using the menus, see page 30.
•
Adjust the Keystone, Contrast, or Brightness in the Picture menu.
•
•
Change the Aspect Ratio. See page 31 for details.
Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture
menu. See page 31.
•
Adjust the Color Space, Temperature or Control in the Advanced
menu.
•
•
Adjust the Phase, Tracking, or Horizontal or Vertical position in the
Advanced menu.
Change the Aspect ratio. Aspect ratio is the ratio of the image width to
image height. TV screens are usually 1.33:1, also known as 4:3. HDTV
and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your
input source. See page 31.
•
Once you have optimized the image for a particular source, you can
save the settings using Presets. This allows you to quickly recall these
settings later. See page 32.
•
Select a Sharpness, Color Temperature, or Video Standard setting. See
page 33.
•
Adjust the Color Control or White Peaking settings. See page 33.
Presentation features
Customizing the projector
Several features are provided to make giving presentations easier. The following is an overview, details are found in the menu section on page 30.
You can customize the projector for your specific setup and needs. See
page 34 to page 39 for details on these features.
•
The remote’s Effect button allows you to assign various features to the
key. The default effect is About. You can select from Blank, Mute,
Aspect Ratio, Source, Auto Image, Freeze, About, and LitePort Rotate.
See page 38 for details.
•
For rear projection, turn Rear mode on in the Settings>System menu.
•
For ceiling mounted projection, turn Ceiling mode on in the Settings>System menu.
•
Turn on Automatic Keystone adjustments.
•
The Freeze effect allows you to freeze the displayed image. This is useful if you want to make changes on your computer without your audience seeing them.
•
Specify which source the projector checks first for active video during
power-up.
•
The Blank button on the remote allows you to display a blank screen
instead of the active source. See page 37.
•
Specify the function of the Effect Key on the remote.
•
Turn the projector’s display messages on and off.
•
The Startup Logo menu option lets you change the default startup
screen to a black, white, or blue screen. See page 37.
•
Turn on power saving features.
•
Specify blank screen colors and startup logos.
•
Two menu options, Power Save and Screen Save, are provided to automatically shut down the projector after several minutes of inactivity or
display a blank screen. This helps preserve lamp life. See page 35.
•
Specify the menu language.
•
Project wirelessly with LiteShow wireless adapter. See page 6.
•
Control your projector using RS-232 commands. See page 8.
29
Using the menus
To open the menus, press the Menu button on the keypad or remote. (The
menus automatically close after 60 seconds if no buttons are pressed.) The
Main menu appears. Use the arrow buttons to move up and down to highlight the desired submenu, then press the Select button.
Menu
button
To change a menu setting, highlight it, press Select, then use the up and
down arrow buttons to adjust the value, select an option using radio buttons, or turn the feature on or off using check boxes. Press Select to confirm
your changes. Use the arrows to navigate to another setting. When your
adjustments are complete, navigate to Exit, then press Select to go to the
previous menu; press the Menu button at any time to close the menus.
Keypad navigation
buttons
Main menu
Dots appear before the menu name. The number of dots indicate the menu’s
level, ranging from one (the Main menu) to four (the most nested menus).
Dots
The menus are grouped by usage:
•
The Picture menu provides image adjustments.
•
The Settings menu provides set-up type adjustments that are not
changed often.
•
The About menu provides a read-only display of information about the
projector and source.
Settings
menu
Certain menu items may be grayed out until a particular source is connected. For example, Sharpness is only available for video sources and will
be hidden when a computer source is active. Other menu items may be
grayed out when they are not available. For example, Brightness is grayed
out until an image is active.
Picture
menu
About menu
30
Picture menu
To adjust the following six settings, highlight the setting, press Select, use
the up and down arrows to adjust the values, then press select to confirm
the changes.
increasing keystone
Keystone: adjusts the image vertically and makes a squarer image. You can
also adjust keystone from the keypad. If you want the projector to automatically adjust the keystone, check the Auto Keystone check box. If you then
manually adjust the keystone, Auto Keystone is turned off. When the projector is in Ceiling Mount mode, Auto Keystone is turned off. You can do a
“one-time” automatic keystone adjustment by pressing both Keystone buttons on the keypad at the same time.
decreasing keystone
Contrast: controls the degree of difference between the lightest and darkest
parts of the picture and changes the amount of black and white in the
image.
Brightness: changes the intensity of the image.
Color: (video and component sources only) adjusts a video image from
black and white to fully saturated color.
Tint: (NTSC video sources only) adjusts the red-green color balance in the
image.
Aspect Ratio
Aspect Ratio: Aspect ratio is the ratio of the image width to image height.
TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are
1.78:1, or 16:9. The default is 4:3, which displays the input resized up or
down to fill the display area.
The aspect ratio selection is saved for each source.
31
Presets: The provided Presets optimize the projector for displaying computer presentations, photographs, and film images. You can use the preset
as a starting point, then further customize the settings for each source. To
restore the factory default settings, choose Factory Reset in the Settings>Service menu.
Presets
There are also three user-definable presets. To set a preset for the current
source, adjust the image, then choose Save User 1, 2, or 3. You can recall
these settings in the future by selecting the appropriate user presets.
32
Advanced settings
Sharpness: (video sources only) changes the clarity of the edges of a video
image. Select a sharpness setting.
Color Space: This option applies to computer sources. It allows you to
select a color space that has been specifically tuned for the video input.
When Auto is selected, the projector automatically determines the standard.
To choose a different setting, turn off Auto, then choose RGB for computer
sources, choose either REC709 or REC601 for component sources.
Color Temperature: changes the intensity of the colors. Select a listed
value.
Sharpness
Advanced
Color Control: allows you to individually modify each color. Highlight the
color, press Select, then use the arrows to adjust the value.
Video Standard: (video sources only) When it is set to Auto, the projector
attempts to pick the video standard automatically based on the input signal
it receives. (The video standard options may vary depending on your region
of the world.) If the projector is unable to detect the correct standard, the
colors may not look right or the image may appear “torn.” If this happens,
manually select a video standard by selecting NTSC, PAL, or SECAM from
the Video Standard menu.
Color Temperature
Color Space
Overscan: (video sources only) removes noise around the video image.
Sync Threshold Adjust: (enhanced and high definition sources only) If a
hardware device, such as a DVD player, is not syncing properly with the
projector, select this option to help it sync.
The following 4 options are for computer and component sources only.
Phase: adjusts the horizontal phase of a computer source.
Video Standard
Tracking: adjusts the vertical scan of a computer source.
Horizontal/Vertical Position: adjusts the position of a computer source.
White Peaking: (video sources only) adjusts the white level processed in
the image. It increases the brightness of whites that are near 100%.
33
Color Control
Settings menu
Audio: allows adjustments to the volume and balance, and turns the projector’s startup Chime on and off.
Audio
Sources: allows you to assign a particular input to a specific source key
when using the optional Integrator remote. Also allows selection of a
default Power-up Source and enables or disables Autosource.
Settings
Sources>Power-up Source: this determines which source the projector
checks first for active video during power-up.
Sources>Autosource: When Autosource is not checked, the projector
defaults to the source selected in Power-up Source. If no source is found, a
blank screen displays. When Autosource is checked, Power-up Source
determines which source the projector defaults to at startup. If no signal is
present, the projector checks the sources in order until a source is found or
until power down.
Sources>Monitor Out Enable: Selects the Computer 2/monitor out connector to be a monitor loop through of the incoming Computer 1 signal
when checked. When it is unchecked, this connector acts as a VESA input.
Sources
System>Rear: reverses the image so you can project from behind a translucent screen.
Auto Ceiling: automatically senses when the projector is inverted and turns
the image upside down. This is On by default. When in Ceiling mode, Auto
Keystone is turned off.
Ceiling: turns the image upside down for ceiling-mounted projection.
Power-up
Source
Auto Power: When Auto Power is checked, the projector automatically
goes into the startup state after the projector is powered on. This allows control of ceiling mounted projectors with a wall power switch.
Low Power: Turn this on to lower the light output of the lamp. This also
lowers the fan speed, making the projector quieter.
System
Display Messages: displays status messages (such as “Searching” or
“Mute”) in the lower-left corner of the screen.
34
Screen Saver Off: prevents your computer from going into Screen Save
mode.
Power Save: automatically turns the lamp off after no signals are detected
for 20 minutes. After 10 additional minutes with no signal, the projector
powers down. If an active signal is received before the projector powers
down, the image will be displayed.
Screen Save: automatically blanks the screen with a black color after no signals are detected for a preset number of minutes. The image returns when
an active source is detected or a remote or keypad button is pressed. Screen
Save is disabled when Power Save is enabled.
Screen Save
System
35
LitePort
This menu allows you to control the embedded LitePort player in your projector to display JPEGs stored on your USB mass storage device. You can
also control the LitePort player with the remote or keypad. See page 27.
Auto Play: When this box is checked (the default), the projector automatically makes the LitePort player the active source and displays, in Full Screen
mode, the first JPEG in the LitePort\AutoPlay folder on the USB drive. If no
AutoPlay folder exists or the AutoPlay folder is empty, then no images will
be displayed and Folder View mode is entered. When this box is unchecked,
you must manually choose the LitePort source using the remote’s computer
button or the source button on the keypad. This will display Folder View
mode. See page 27 for details on selecting images to display using the
remote or keypad.
LitePort
Play All: When this box is checked, the projector plays all the JPEGs in all
the folders on the USB drive, starting with the current folder and continuing
in alphanumeric folder order. If it is unchecked, only the JPEGs in the
selected folder are displayed, and these JPEGs play on a continuous loop.
Auto Advance
Fit to Screen: This causes the image to fill the entire screen. If the image has
a different aspect ratio than the screen, the image will fit in width or height,
depending upon which is larger. Any empty space will be filled with black.
Auto Advance: This option lets you automatically advance images and
determine how long each image is displayed before advancing to the next
image. Click the check box to turn it on, then highlight Seconds and use the
Up/Down arrows on the keypad or remote to increase or decrease the display time. When playing images with this option, you can go back to the
previous slide by pressing the Up arrow or ahead to the next slide quicker
by pressing the Down arrow. Press the Select button to stop Auto Advance
and return to File View mode.
Slide Transition
Slide Transition: This allows you to customize your presentation with slide
transitions. Select among None (no transition), Random, Wipe Up, Wipe
Down, Wipe Left, Wipe Right, Split Horizontal In, Split Horizontal Out,
Split Vertical In, Split Vertical Out, Horizontal Blinds, Vertical Blinds, Box
In, and Box Out. For a demonstration of these transitions, go to the Slide
Show>Slide Transition menu in PowerPoint.
36
Startup Logo: allows you to display a blank Black, White, or Blue screen
instead of the default screen at startup and when no source is detected.
Startup Logo
Blank Screen: determines what color is displayed when you press the
Blank button on the remote.
Blank Screen
37
Effect Key: allows you to assign a different function to the Effect button on
the remote to quickly and easily use the effect. Only one effect can be
enabled at a time. Highlight an effect and press Select to choose a different
one. The default effect is About.
Blank: shows an empty screen.
Mute: turns off all sound.
Effect Key
Aspect Ratio: sets the ratio of the image width to image height.
Source: cycles through the available sources.
Auto Image: causes computer sources to be reacquired.
Freeze: pauses the projected image.
About: displays the About menu.
LitePort Rotate: rotates an image clockwise that is displayed with
LitePort.
Language: allows you to select a language for the onscreen display of
menus and messages.
Service: to use these features, highlight them and press Select.
Factory Reset: restores all settings (except Lamp Hours) to their default
after displaying a confirmation dialog box.
Language
Lamp Reset: resets the lamp hours counter in the About menu to zero. Do
this only after changing the lamp. It displays a confirmation dialog box.
Service Code: only used by authorized service personnel.
Service
38
Maintenance
clean the lens
with a soft dry cloth
and non-abrasive
cleaner
Cleaning the lens
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
Avoid using an excessive amount of cleaner, and don’t apply the
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh
chemicals might scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you
don’t intend to use the projector immediately, replace the lens cap.
Using the security lock
The projector has a security lock for use with a cable lock system. See
“Accessories” on page 43 for ordering information. Refer to the information
that came with the lock for instructions on how to use it.
security lock
39
Replacing the projection lamp
The lamp hour timer in the About menu counts the number of hours the
lamp has been in use. Fifty hours before the specified end of the lamp’s life,
the message “Replace lamp” briefly appears on the screen at each startup
and in the Interactive Display. After 50 additional hours, the lamp will no
longer light. You can order new lamp modules from your dealer. See
“Accessories” on page 43 for information.
About menu
turn off and unplug
the projector
1 Turn off the projector and unplug the power cable.
2 Wait 60 minutes to allow the projector to cool thoroughly.
wait 60 minutes
3 Turn the projector upside down and remove the lamp door by placing a
flat-blade screwdriver into the space between the lamp door and the
projector and gently prying the door off.
pry the lamp door off
4 Loosen the captive screw on the lamp module.
loosen the screw on lamp module
WARNINGS:
•
To avoid burns, allow the projector to cool for at least 60 minutes before
you replace the lamp.
•
Unplug the power cord before replacing the lamp.
•
Do not drop the lamp module. The glass may shatter and cause injury.
•
Do not touch the glass lamp screen. Fingerprints can obscure projection
sharpness.
40
•
Be extremely careful when removing the lamp housing. In the unlikely
event that the lamp ruptures, small glass fragments may be generated.
The lamp module is designed to contain most of these fragments, but
use caution when removing it. Before replacing a ruptured lamp, clean
the lamp compartment and dispose of cleaning materials. Wash hands
after lamp replacement. This product has a lamp which contains a very
small amount of mercury. Dispose of it as required by local, state or federal ordinances and regulations. For more information see
www.eiae.org.
disconnect lamp connector
5 Detach the lamp connector from the projector by depressing the locking
tab on the connector and lightly pulling it free.
6 Carefully remove the lamp module by grasping and lifting the metal
bail wire. Dispose of the lamp in an environmentally proper manner.
7 Install the new lamp module, making sure that it is properly seated. Be
careful not to touch the interior components of the projector.
remove module using bail wire
8 Snap the bail wire back into its flat position against the lamp module.
9 Re-attach the lamp connector to the projector. The locking tab should
engage when the connector is fully plugged in.
10 Tighten the screw on the lamp module.
11 Replace the lamp door.
12 Plug in the power cable then press the Power button to turn the projector back on, then reset the lamp hour timer.
Resetting the lamp timer
If the lamp timer has reached the maximum number of hours for the projector lamp, the LED on the projector’s keypad will show a lamp error (see
“LED behavior and meaning” on page 16). To reset the lamp timer, press the
decrease volume button on the keypad and the increase volume button
simultaneously for 10 seconds. You can also navigate to the Settings>Service menu and select Lamp Reset to reset the lamp timer.
reset lamp time in Service menu
41
Cleaning the lamp filter screens
In dirty or dusty environments, the dust filter screens on the lamp module
and lamp door and in the lamp compartment can become clogged, causing
high temperatures inside the lamp module. These high temperatures can
impact lamp performance and operating life. Routine maintenance to
remove dust and dirt from the screens lowers the lamp operating temperature and prolongs lamp life. To maximize lamp life you will need to clean
the screens every 250 hours. Lamp screen maintenance may need to occur
more often than 250 hours depending on your installation/use environment.
screen
screen
1 Remove the lamp module. Refer to page 40 for instructions.
2 Examine the dust filter screens on each side of the lamp module. If necessary, use compressed or canned air to clean the screens. Then use a
cotton swab dipped in isopropyl alcohol to lightly wipe each screen.
After you've wiped each screen, blow away any remaining contaminants.
3 Examine the dust filter screen on the lamp door. If necessary, use compressed or canned air to clean the screen. Then use a cotton swab dipped
in isopropyl alcohol to lightly wipe the screen. After you've wiped the
screen, blow away any remaining contaminants.
screen
4 Before you replace the lamp, repeat the cleaning process on the screen in
the lamp compartment in the projector.
5 Replace the lamp module and lamp door.
screen
42
Appendix
Accessories
Standard Accessories
(ship with the projector)
Part Number
Carry Case
Optional Accessories
Part Number
Shipping Case (ATA approved)
CA-ATA-020
Projector Mount
SP-CEIL-011
False Ceiling Plate for Projector Mount
SP-LTMT-PLT
SP-LTMT-EXTP
110-0819-xx
Extension Arm for Projector Mount
26” - 47”
Computer Cable 6 ft (1.8 m)
SP-DVI-A
Organizer Carry Case
CA-C230
Video Cable 6 ft (1.8 m)
210-0176-xx
DVI-D Cable 6 ft (1.8 m)
SP-DVI-D
Audio Cable 6 ft (1.8 m)
210-0118-xx
M1 to Component Adaptor
SP-M1-ADPT
Audio Cable Adapter
210-0177-xx
LiteShow Wireless Connection
LP-LITESHOW
Power Cable*
516-0052-xx
Audio/Video Cable, 30 ft (9m)
SP-AV30
Navigator Remote
590-0728-xx
Projector Cable Lock System
SP-LOCK-B
Projection Lamp Module (included
in projector)
SP-LAMP-019
50” Diagonal Screen (portable)
A650
60” Diagonal Screen (portable)
HW-DLXSCRN
Lens Cap
340-1347-xx
84” Diagonal Wall/Ceiling Mounted Screen
HW-WALLSCR84
Lens Cap Tether
321-0192-xx
Quick Setup card
009-0911-xx
User’s Guide with CD
010-0549-xx
Safety Card
009-0659-xx
Color-coded Cable Ties, 3 set
SP-CABLETIES
SCART Adapter*
301130
*country-dependent
NOTE: Use only approved accessories.
43
Replacement Lamp Module
SP-LAMP-019
RF Presenter Remote Control
HW-PRESENTER-RF
IR Presenter Remote Control
HW-PRESENTER
IR Conductor + Remote Control
HW-CONDUCTOR+
Red LED behavior and projector errors
Projected image size
Table 5:
Image sizes
If the projector is not functioning properly and the red LED is blinking, consult Table 2 to determine a possible cause. There are two second pauses
between the blinking cycles. Visit our website for more details on the red
LED error codes. See the inside back cover for contact information.
Distance
to screen
(feet/m)
5/1.5
10/3
15/4.6
20/6.1
30/9.1
32.8/10
Table 4:
Red LED Behavior
Explanation
One (1) blink
The lamp won't strike after five (5)
attempts. Check the lamp and lamp door
installations for loose connections.
Two (2) blinks
The lamp counter hours have exceeded
lamp life hours. Replace the lamp and
reset the lamp hours counter.
Three (3) blinks
The projector has shut down the lamp.
Replace the lamp. Contact Technical Support for repair if replacing the lamp does
not solve the problem.
Four (4) blinks
The fan has failed. Contact Technical Support for repair.
Five (5) blinks
The projector is overheating. Check for a
blocked air vent. Contact Technical Support for repair if clearing the air vents
does not solve the problem.
Minimum
Diagonal
(feet/m)
Maximum
Diagonal
(feet/m)
Minimum
Horizontal
(feet/m)
Maximum
Horizontal
(feet/m)
2.75/0.83
5.5/1.65
8.25/2.53
11/3.36
16.5/5.01
18.0/5.5
3.4/1.02
6.8/2.04
10.2/3.13
13.6/4.15
20.4/6.19
22.3/6.8
2.2/0.66
4.41/1.32
6.61/2.03
8.81/2.69
13.22/4.01
14.45/4.41
2.73/0.82
5.46/1.64
8.2/2.51
10.93/3.33
16.39/4.97
17.92/5.46
NOTE: Visit our website for an interactive image size calculator.
44
INDEX
C
cables
optional 43
standard 43
Ceiling 34
cleaning the lamp filter screens 42
cleaning the lens 39
Color 15, 31
Color Control 33
Color Space 33
Color Temperature 33
colors are incorrect 22
Computer 2 connector 8
computer connections
optional 7
required 7
computer image
optimize 29
troubleshooting 17
connecting
computer 7
external speakers 28
USB device 8
video device 13
connector panel 6
contacting InFocus 24
Contrast 12, 15, 31
customer service contact information 24
Numerics
1024x768 resolution 5
A
About menu 30, 38
Advanced setting 33
advancing PowerPoint slides 7
advancing PowerPoint slides with LitePort 27
Aspect Ratio 31, 38
audio 28
audio adapter 13
Audio In connector 7, 13
audio volume 15
audio, troubleshooting 28
Auto Advance 36
Auto Ceiling 34
Auto Image 38
Auto Play 36
Auto Power 34
Autosource 34
B
Blank screen 37, 38
blinking green 16
blinking red 16
Brightness 12
45
D
Display Messages 34
displaying
computer image 9
JPEG image 27
video image 14
displaying JPEG images with LitePort player 27
Drivers 10
USB 11
Windows 98 11
I
image
display computer 9
display JPEG 27
display video 14
image does not fit screen 21
image not centered 23
image not sharp 21
image not square 21
image reversed 22
image size matrix 44
image upside down 22
Interactive Display 5
E
Effect Key 38
elevator foot 12
K
keypad buttons 25
keystone 12, 31
F
Factory Reset 38
first time use
driver installation 10
Fit to Screen 36
focus 12, 15
Freeze 38
fuzzy image 18
L
lamp
cleaning filter screens 42
lamp replacement 40
Lamp Reset 38
lamp screens, cleaning 42
lamp won’t turn on 23, 24
Language 38
laptop
connecting 7
external video port 9
LED
blinking green 16
blinking red 23
solid green 16
solid red 24
LED behavior 16
lens cap tether 5
46
lens, cleaning 39
leveling foot 12
LitePort
connector 6, 8
menu 36
player 6, 8, 27, 36
player modes 27
Rotate effect key 38
rotating images 38
LitePort Utility software 6
LiteShow 6
lock, security 39
Low Power 34
P
Picture menu 31
Play All 36
Position 33
power cable 7, 13
Power Save 16, 35
PowerPoint, advancing slides 7
Power-up Source 34
presentation features 29
projected image sizes 44
projector
adjusting the height 12, 14
connector panel 6
customizing 29
LitePort player 8, 27
optional accessories 43
positioning 12
shutdown 16
standard accessories 43
troubleshooting problems 16
USB connector 8
M
Macintosh troubleshooting 19
Main menu 30
menu system 30
Monitor connector 8
Monitor Out Enable 34
Mute 38
N
no computer image 18
no startup screen 17
R
Rear 34
registering your projector 5
remote control 26
advancing slides 26
Effect key 26
not working 20
Previous/Next buttons 26
replacing the lamp 40
Reset 38
resetting the lamp timer 41
resolution 5
RS-232 6, 8
O
online registration 5
only startup screen appears 17
onscreen menus 30
optional accessories 43
Overscan 33
47
S
safety considerations 4
Screen Save 16, 35
Screen Saver 35
screens, cleaning 42
security lock 39
serial connection 8
Service 38
Settings menu 34
Sharpness 33
shutting down the projector 16
Slide Transition 36
solid green 16
solid red 16
Source troubleshooting 17
Sources 34
speakers, connecting 28
standard accessories 43
Startup Logo 37
S-video connector 13
Sync Threshold Adjust 33
U
USB drivers 11
USB mass storage device 8
USB, connecting 7
using the keypad buttons 25
V
VESA connector 8
video connections
optional 13
standard 13
Video connector 13
video images, optimizing 29
Video Standard 33
W
White Peaking 33
Windows 2000 11
Windows 98 10
Windows ME, XP 11
wireless projection 6
X
XGA 5
T
Tint 15, 31
Tracking 33
Troubleshooting 16, 17
Turning off the projector 16
Z
zoom 12, 15
48
6654_C170_UG.QXD 4/20/04 3:11 PM Page 2
IF YOU NEED ASSISTANCE....
WARNING: The power cord and cables associated
with this product contain lead, a chemical
known to the state of California to cause birth
defects or other reproductive harm. Wash
hands after handling.
WARNING: This product has a lamp which
contains a very small amount of mercury.
Dispose of it as required by local, state, or
federal ordinances and regulations. For more
information, see www.eiae.org
For all types of Service and Support information on our products
and services please go to our website at www.askproxima.com
Many resources are available on our website.
Some examples are:
• Frequently Asked Questions about general
projector usage and technical issues
• E-mail support
• Online product registration
• Product data sheets
• Optional accessories
• Technical specifications, interactive image size calculator,
laptop activation commands and more!
6654_C170_UG.QXD 4/20/04 3:11 PM Page 1
>>>>>>>
InFocus Corporation
27700B SW Parkway Avenue
Wilsonville, Oregon 97070-9215
1-800-294-6400 • 503-685-8888
Fax: 503-685-8887
http://www.infocus.com
In Europe:
InFocus International B.V.
Strawinskylaan 585
1077 XX Amsterdam,The Netherlands
Phone: +31 20 579 2000
Fax: +31 20 579 2999
In Asia:
InFocus Systems Asia Pte Ltd.
238A Thomson Road
#18-01/04 Novena Square
Singapore 307684
Telephone: (65) 6334-9005
Fax: (65) 6333-4525
User’s
Guide