Technical information | Aspire Digital 1360 Laptop User Manual

Aspire 2010
Aspire 2020
Service Guide
Service guide files and updates are available
on the ACER/CSD web; for more information,
please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
NOTE: This is Aspire 2000 extension model. Please refer to Aspire 2000
Service CD(P/N: VD.A20V5.001) for the disassemble mpeg file.
Revision History
Please refer to the table below for the updates made on Aspire 2010/2020 service guide.
D ate
II
Chapter
Updates
Copyright
Copyright © 2004 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
III
Conventions
The following conventions are used in this manual:
IV
SCREEN
MESSAGES
Denotes actual messages that appear
on screen.
NOTE
Gives bits and pieces of additional
information related to the current
topic.
WARNING
Alerts you to any damage that might
result from doing or not doing specific
actions.
CAUTION
Gives precautionary measures to
avoid possible hardware or software
problems.
IMPORTANT
Reminds you to do specific actions
relevant to the accomplishment of
procedures.
Preface
Before using this information and the product it supports, please read the following general information.
1.
This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's "global" product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2.
Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.
V
Table of Contents
Chapter 1
System Specifications
1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Outlook View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Aspire 2010 Open View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Aspire 2010 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Aspire 2010 Top Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Aspire 2010 Left Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Aspire 2010 Right Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Aspire 2010 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Aspire 2010 Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Aspire 2020 Open View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Aspire 2020 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Aspire 2020 Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Aspire 2020 Left View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Aspire 2020 Right View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Aspire 2020 Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Aspire 2020 Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Embedded Numberic Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Windows Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
The Euro Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Touchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Launch Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Hardware Specifications and Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Chapter 2
System Utilities
42
BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Navigating the BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
BIOS Flash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Chapter 3
Machine Disassembly and Replacement
58
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Disassembly Procedure Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Disassemble the Battery and HDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Disassemble the Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Disassemble the RAM and ODD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Disassemble the Middle Cover Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Disassemble the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Disassemble the LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Disassemble the MDC and RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Disassemble the Upper Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
VII
Table of Contents
Disassemble the Main Unit(Touchpad, Bluetooth and LCM Board) . . . . . . . . . .65
Disassemble the Main Unit(Speakers, Fan, Thermal and CPU) . . . . . . . . . . . .66
Disassemble the Main Unit(VGA, Card Reader, Sub-Woofer and M/B) . . . . . . .67
Disassemble the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Disassemble the ODD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Disassemble the HDD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Chapter 4
Troubleshooting
70
System Check Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
External Diskette Drive Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
External CD-ROM/DVD ROM Drive Check . . . . . . . . . . . . . . . . . . . . . . . .71
Keyboard or Auxiliary Input Device Check . . . . . . . . . . . . . . . . . . . . . . . . .72
Memory Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Power System Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Check the Power Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Check the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Touchpad Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Display Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Sound Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Insyde MobilePro BIOS POST Beep code and POST Messages . . . . . . . . . . .76
Index of Symptom-to-FRU Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Intermittent Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Undetermined Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
How to Build NAPP Master Hard Disc Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
CD to Disk Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Disk to Disk Recovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Chpater 5
Jumper and Connector Locations
91
Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
Power Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
TouchPad Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
SD Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
Media Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
LED Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Bottom Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Chapter 6
FRU (Field Replaceable Unit) List
101
Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
Aspire 2010 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103
Aspire 2020 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
Appendix A Model Definition and Configuration
113
Appendix B Test Compatible Components
114
Microsoft Windows XP Home Environment Test . . . . . . . . . . . . . . . . . . . . . . .115
Microsoft Windows XP Professional Environment Test . . . . . . . . . . . . . . . . . . .118
Appendix C Online Support Information
VIII
121
Chapter 1
System Specifications
Features
This computer was designed with the user in mind. Here are just a few of its many features:
Performance
T
Intel® Pentium M processor at 1.4~ 1.8 GMHz or higher with uPGA478 socket
T
Intel 855GME + Intel ICH4-M
T
1MB L2 cache or 2MB L2 cache, 400MHz FSB, supporting Enhanced Intel SpeedStep®
technology
T
30GB and up Enhanced-IDE hard disk drive
T
512KB Flash BIOS ROM
Memory
T
256MB of DDR333 memory, upgradeable to 2GB with dual SODIMM modules
T
0MB DDR RAM on board
Two 256MB of DDR333 SODIMM (200-pin/2.5V/1.25V) connector,upgradeable to 2GB with dual
SODIMM modules
NOTE: (Small Outline-DIMM) A DIMM module with a thinner profile due to the use of TSOP chip packages.
SODIMMs are commonly used in laptop computers
T
The pic of SODIMM as showing : (copyright from Techweb)
Display
Chapter 1
T
Thin-Film Transistor (TFT) liquid-crystal display (LCD) displaying 32-bit high true colour up to 16.7
million colours at 1280x800 eXtended Graphics Array (WXGA) resolution
T
The 15.4” display panel provides a large viewing area for maximum efficiency and ease-of-use
T
16:10 viewing ratio, 185 nits or higher
T
Console display for Arcade media playback status
T
Intel® Extreme Graphics Technology (for Aspire 2010 use only)
T
ATI Radeon 9700 with 64MB DDR VGA Memory (for model with Discrete VGA only)
T
ATI Radeon 9700 with 128MB DDR VGA Memory (for model with Aspire 2020 only)
T
Supports simultaneous display on external LCD or CRT
T
One LED console display for multimedia status (for Aspire 2020 only)
T
S-video for output to a television or display device that supports S-video input
T
DualViewTM support
T
External resolution/refresh rate
T
2040x1536:75/70/66/60 Hz
T
1920x1440: 85/75/60 Hz
1
T
1920x1200: 100/85/80/75/72/60 Hz
T
1600x1200:120/100/92/85/76/75/72/70/66/65/60/58/52 Hz
T
1280x1024: 160/120/100/90/85/75/74/72/70/60 Hz
T
1280x768: 85/75/60/56 Hz
T
1024x768: 200/160/150/140/120/100/90/85/75/72/70/60 Hz
T
800x600: 200/160/140/120/100/90/85/75/72/70/60/56 Hz
Multimedia
T
Built-in optical drive (Tray loading DVD/CD-RW Combo or DVD Super-Mulit Drive Aspire 2010
only)
T
Built-in optical drive (Slot-loading DVD/CD-RW Combo or DVD Super-Multi or Tray-loading DVD
Dual Drive Aspire 2020 only)
T
15.4” TFT Color LCD, 1280x800 (WXGA) panel
T
2.1 channel speaker
T
Audio input and output jacks
T
Audio S/PDIF (for digital audio enjoyment) output jacks (for Aspire 2020 only)
T
Aspire virtual surround sound ( for Aspire 2010 only)
T
Aspire virtual surround sound with built-in sub-woofer (for Aspire 2020 only)
T
30/40/60/80 GB ATA/100 hard disc drive
T
4-in-1 card reader, supporting :
Storage
T
MultiMedia Card (MMC)
T
Secure Digital (SD)
T
SmartMedia
T
Memory Stick (For module with Discrete VGA only)
Connectivity
T
Integrated 10/100Mbps Ethernet Connection
T
Built-in 56Kbps fax /data modem with international PTT approval, Wake-On-Ring ready
T
Three universal serial bus (USB 2.0) ports
T
One IEEE 1394 port
T
LAN: 10/100 Mbps Fast Ethernet; Wake-on-LAN ready (for Aspire 2010 only)
10/100/1000 Mbps Fast Ethernet; Wake-on-LAN ready (for Aspire 2020 only)
T
802.11b and 802.11b/g Wireless LAN and Bluetooth
Human-Centric Design
2
T
Rugged, portable construction
T
Stylish appearance
T
Standard 85 key keyboard with four programmable launch keys
T
Comfortable palm rest area with well-positioned touchpad
Chapter 1
Graphics
T
T
T
Intel® 855GME integrated 3D AGP graphics featuring Intel® Extreme Graphics 2 technology and
up to 64MB of video memory (for model with UMA only)
ATI Radeon 9700 with 64MB DDR VGA Memory (for model with Discrete VGA only)
ATI MOBILITYTM RADEONTM 9700 with 128MB of external DDR video RAM, supporting
Microsoft® DirectX® 9.0 (for Aspire 2020 only)
T
Simultaneous LCD and CRT display at 2040x1536 pixel resolution
T
DuralViewTM support
T
Aspire cinema vision video encoded technology
T
Aspire clear vision video input optimisation technology
T
MPEG-2 DVD hardware-assisted capability
T
S-Video/TV-out support (NTSC/PAL)
Expansion
T
PC card slot enables a range of add-on options
T
Upgradeable hard disk and memory modules
I/O Ports
Chapter 1
T
Three USB 2.0 ports
T
IEEE 1394 port
T
Ethernet (RJ-45) port
T
Modem (RJ-11) port
T
S-video TV-Out (NTSC/PAL) port
T
Parallel port
T
External display (VGA) port
T
Microphone/Line-in Jack
T
Headphone/Speaker/Line-out Jack (S/PDIF support for Aspire 2020 only)
T
Infrared (FIR) port
T
PC Card slot (one type II, supports 16-bit PCMCIA and 32-bit CardBus specifications)
T
DC-in Jack for AC adapter
3
System Block Diagram
4
Chapter 1
Board Layout
Top View
Rear View
Chapter 1
5
Item
6
Description
Item
Description
JP1
RJ11/RJ45 Connector
JP20
Int. K/B Connector
JP2
CRT Connector
JP21
Bluetooth Connector
JP3
Printer Connector
JP22
DDR SODIMM Socket
JP4
TV-Out Connector
JP23
ODD Connector
JP5
USB Connector
JP24
T/P Board Connector
JP6
USB Connector
JP25
HDD Connector
JP7
USB Connector
JP27
MINIPCI Connector
JP8
IEEE 1394 Connector
JP29
DDR SODIMM Socket
JP9
Power Board Connector
PCN2
AC Jack Connector
JP10
MDC Cable Connector
PCN3
Battery Connector
JP11
LCD Connector
U4
LAN Chip
JP12
Cardbus Connector
U11
North Bridge Chip
JP13
FAN Connector
U12
VGA Chip
JP14
MDC Connector
U14
South Bridge Chip
JP15
Right Speaker Connector
U16
CPU Socket
JP16
Left Speaker Connector
U31
FIR
JP17
Subwoofer Connector
U40
BIOS ROM
JP18
LCM Connector
U45
Cardbus Controller
JP19
SD Board Connector
T1
LAN Transformer
Chapter 1
Outlook View
A general introduction of ports allow you to connect peripheral devices, as you would with a desktop PC.
Aspire 2010 Open View
#
Chapter 1
Item
Description
1
Screen
Wide screen display provides visual output.
2
Power Button
Turns the computer on or off
3
Launch Keys
Buttons that can be programmed to start frequently used
applicatoins.
4
Stereo Speakers
Produce stereo sound
5
Touchpad
Touch sensitive pad that functions like a computer mouse.
6
Click buttons and 4way scroll key
Right and left buttons that provide the same functions as th
buttons on a computer mouse. The scroll key scrolls the
contents of a window up and down, as well as right and left.
7
Aspire 2010 Front Panel
#
8
Icon
Item
Description
1
Headphone-in Jack
Connects headphones for audio
output.
2
Microphone-in Jack
Connects an external microphone for
audio input
3
4 in 1 Card Reader
Supports:
T
Memory Stick
T
MultiMediaCard
T
SecureDigital
T
SmartMedia
4
Latch
Locks and releases the lid
5
Bluetooth Button
Starts Bluetooth functionality
6
Wireless Button
Turns an internal wireless device on or
off
Chapter 1
Aspire 2010 Top Panel
Chapter 1
#
Item
1
Built-in Microphone
For recording audio on the computer
Description
2
Status Indicator
LEDs that turn on and off to show the
system status
9
Aspire 2010 Left Panel
#
10
Item
Description
1
PC Card Slot
Type II PC card slot, supports PCMCIA or CardBus
2
PC card eject button
Press the eject button to remove a PC card from the
PC card slot
3
LED Indicator
Lights up when the optical drive in active
4
Eject Button
Ejects optical drive tray
5
Emergency eject hole
Ejects optical drive tray when the computer is turned
off.
Chapter 1
Aspire 2010 Right Panel
#
Chapter 1
Item
Description
1
Infrared Port
Interfaces with infrared devices (e.g., infrared printer,
IR-aware computer)
2
DC-in Jack
Connect the AC adapter
3
Kensington lock slot
For attaching a security connector.
4
Ventilation Hole
Enables the computer to stay cool, even after
prolonged use.
11
Aspire 2010 Rear Panel
#
Item
Description
1
S-Video
Connects to a television or display device with Svideo input.
2
External display port
Connects an external (VGA) display monitor.
USB Ports
Three USB2.0 ports for connecting USB devices.
5
Network Jack
Connects the computer to an Ethernet 10/100-based
network.
6
Modem Jack
Connects the built-in fax/data modem to a phone
line.
7
Parallel Port
Connects a parallel device, such as a printer.
9
IEEE 1394 Port
Connects IEEE 1394 devices.
3,4,8
12
Icon
Chapter 1
Aspire 2010 Bottom View
#
Chapter 1
Item
Description
1
Mini-PCI Slot
Slot for adding mini-PCI cards
2
Hard Disk Bay
Removable cover provides access to the computer’s hard
drive.
3
Memory Compartment
Removable cover provides access to the memory slots for
upgrading the computer’s memory.
4
Battery Release Latch
Unlatches the battery to remove the battery pack
5
Battery Pack
The computer’s removable battery
13
Aspire 2020 Open View
#
14
Item
Description
1
Screen
Wide screen display provides visual output
2
Power Button
Turns the computer on or off
3
Launch Keys
Buttons that can be programmed to start
frequently used applications
4
Stereo Speakers
Produce stereo sound
5
Touchpad
Touch sensitive pad that functions like a
computer mouse
6
Click buttons and 4-way
scroll key
Right and left button that provide the same
functions as the buttons on a computer
mouse. The scroll key scrolls the contents
of a window up and down, as well as right
and left
Chapter 1
Aspire 2020 Front View
#
Chapter 1
Icon
Item
Description
1
Headphone-in Jack
Connects headphones for audio output
2
Microphone-in Jack
Connects an external microphone for
audio input
3
4 in 1 Card Reader
Supports:
T
MemoryStick
T
MulitMediaCard
T
SecureDigital
T
SmartMedia
4
Latch
Locks and release the lid
5
Bluetooth Button
Enables Bluetooth functionality
(manufacturing option)
6
Wireless Button
Enables Wireless Connectivity
(manufacturing option)
15
Aspire 2020 Top View
#
16
Item
Description
1
Built-In Microphone
For recording audio on the computer
2
Status Indicator
LEDs that turn on and off to show system
status
3
Arcade Button
Multimedia button
4
Console display
Media status display
5
Stop
Stop the Arcade application
6
Media Controls
Multimedia Button
Chapter 1
Asipre 2020 Left View
#
Chapter 1
Item
Description
1
PC card slot
Type II PC card supports PCMCIA or
CardBus
2
PC card eject button
Press the eject button to remove a PC card
from the PC card slot
3
Eject button
Ejects optical disc
4
Slot-loading Optical
Support an optical disc
17
Aspire 2020 Right View
#
18
Item
Description
1
Infrared Port
Interfaces with infrared
devices(e.g. infrared printer, IR.
aware computer, etc..)
2
DC-in Jack
Connect the AC power adapter
3
Kensingtone lock slot
For attaching a security device
4
Ventilation slot
Enables the computer to stay cool,
even after prolonged use
Chapter 1
Aspire 2020 Rear View
#
Item
Description
S-Video
Connects to a television
or display device with Svideo input.
2
External display port
Connects an external
(VGA) display monitor.
USB Ports
Three USB2.0 ports for
connecting USB devices.
5
Network Jack
Connects the computer
to an Ethernet 10/100based network.
6
Modem Jack
Connects the built-in fax/
data modem to a phone
line.
7
Parallel Port
Connects a parallel
device, such as a printer.
9
IEEE 1394 Port
Connects IEEE 1394
devices.
3,4,8
Chapter 1
Icon
1
19
Aspire 2020 Bottom View
#
20
Item
Description
1
Mini-PCI Slot
Slot for adding mini-PCI slot
2
Hard Disk Bay
Removable cover provides access to the
computer’s hard disk drive
3
Memory Compartment
Removable cover provides access to the
memory slots for upgrading the computer’s
memory
4
Battery Release Latch
Unlatches the battery to remove the battery
pack
5
Battery Pack
The computer’s removable battery
6
Sub-Woofer
Outputs low/mid range audio
Chapter 1
Indicators
Your computer provides an array of three indicators located above the keyboard, in addition to four
indicators positioned at the front of the palm rest area. These indicators show the status of the computer
and its componetns.
Aspire 2010
Aspire 2020
The three indicators located above the keyboard provide the following status information:
Icon
Description
Caps Lock activity
Blue -- Captial lock is on
Num Lock activiy
Blue -- Number lock is on
Scroll Lock activity
NOTE: The keypad lock must be turned on to use the embedded numeric keypad.
Chapter 1
21
The four indicators located at the front of the unit provide the following status information:
Icon
Item
T
Off --System Off
T
Green -- System On
T
Orange -- System in standby mode (S3
state)
T
Orange Flashing --System Entering
hibernation mode (S4 state) until
process complete
T
Readable when LCD lid closed
T
Flashing --Media is active
T
Media includes all internal media
devices, such as HDD and ODD.
Email
T
Flash when receiving mails
Hard Disc mode
T
Hard disc drive is reading or writing
data
Battery mode
T
Blue -- fully charged
T
Flashing orange -- Low power
T
Orange -- Charging
T
Readable when LCD lid closed
T
Bluetooth wireless connection is
enabled
T
Blue -- Internal Bluetooth is on
T
Readable when LCD lid closed
T
Wireless LAN communication is
enabled
T
Orange -- Internal WLAN device
(802.11a/802.11b/802.11g) is on
T
Readable when LCD lid closed
Power mode
Media Activity
Bluetooth mode
Wireless LAN mode
22
Description
Chapter 1
Keyboard
The keyboard features full-size keys with an embedded keypad, separated cursor keys, two Windows
keys, and twelve function keys (hot keys).
Special keys
Lock keys
Aspire 2010
Aspire 2020
The computer features three lock keys, each with its own status indicator light.
Lock Key
Description
Caps Lock
When Caps Lock is on, all alphabetic characters are typed in
uppercase. Toggle on and off by pressing the Caps Lock key on
the left side of the keyboard.
Num lock
When Num Lock is on, the embedded numeric keyboard can be
used. Toggle on and off by pressing the Fn+tkeys
simultaneously.
Scroll lock
When Scroll Lock is on, the screen toggles up or down one line
at a time when the up and down cursor control keys are pressed.
NOTE: Scroll Lock doesn’t work in all applications. Toggle on and off by pressing the Fn+F12 keys
simultaneously.
Chapter 1
23
Embedded Keypad
The embedded keypad functions like a desktop numeric keypad. It is indicated by small blue numbers and on
the applicable keys.
To use the the embedded numeric keys, toggle the Num Lock on by pressing the Fn + F11 keys
simultaneously.
With the embedded keypad turned on, the following actions are possible:
Desired Access
Num Lock On
Number keys on
embedded keypad
Type numbers using
embedded keypad in the
normal way.
Cursor-control keys on
embedded keypad
Main keyboard keys
24
Num Lock On
Hold down the jkey
while using the cursor
keys on the embedded
keypad.
Hold Fn key while using
cursor-control keys.
Hold down the Fn key
while typing letters using
the embedded keypad
keys. Simultaneously
press the j key for for
capital letters.
Type letters in the normal
way.
Chapter 1
Hotkeys
Using the Fn key with another key creates a hot key, providing a quick and convenient method for controlling
various functions.
To use a hot key, first hold down the Fn key. Next, press the second key in combination. Finally, release
both keys.
Aspire 2010
Chapter 1
25
Your computer provides the following hot keys:
Hot Key
Function
Description
Fn+F1
Hot key help
This key will cause a help message to appear on the
display device that describes the definition and
functionality of the unit hot keys. It is preferred to have the
key activate a graphical display.
Fn+F2
Access System Properties
This key will launch My Computer > System Properties
Fn+F3
Power management scheme
toggle
Switches the power management scheme used by the
computer (function available if supported by operating
system).
Fn+F4
Sleep
In ACPI mode, the OS provides two buttons for sleep
function. One is the Power On button and the other is the
Sleep Button. °Fn+F4” is assigned as the Sleep
button in ACPI mode. User can set the action of the Sleep
Button on the Power Management property.
Fn+F5
Display toggle
The Hotkey, Display Toggle, is to change the display type
at run-time. Possible display types are LCD, CRT and
Both. It can not detect the CRT, even when the CRT is not
connected. Press Hotkey can force to switch to CRT. This
Hotkey cannot switch the display to TV at DOS.
Fn+F6
Screen blank
This key will cause the LCD back light to be turned off.
This provides both a quick security feature and some
power savings. The LCD back light can also be turned off
via an APM timer. The LCD back light will be turned on
again when any of the following events occur:
T
Any key pressed
T
Pointing device movement
USB Device does not need to support.
Fn+F7
Touchpad toggle
This key will cause the internal touchpad pointing device
to be disabled. This is to prevent accidental system wakeups from standby. Pressing this key a second time will reenable the touch pad pointing device. BIOS check Internal
AuxDev ifnot exist then BIOS empty return.
Fn+F8
Speaker toggle
This key will cause the audio output to the speakers to
muted or disabled. Pressing this key a second time will reenable the audio output to the speakers.
Fn+w
Volume up
Increases the speaker volume.
Fn+y
Volume down
Decreases the speaker volume.
Fn+x
Brightness up
Increases the screen brightness.
Fn+z
Brightness down
Decreases the screen brightness.
NOTE: When activating hotkeys, press and hold the Fn key before pressing the other key in the hotkey
combination.
26
Chapter 1
Aspire 2020
Your computer provides the following hot keys:
Hot Key
Function
Description
Fn+F1
Hot key help
This key will cause a help message to appear on the
display device that describes the definition and
functionality of the unit hot keys. It is preferred to have the
key activate a graphical display.
Fn+F2
Access System Properties
This key will launch My Computer > System Properties
Fn+F3
Power management scheme
toggle
Switches the power management scheme used by the
computer (function available if supported by operating
system).
Fn+F4
Sleep
In ACPI mode, the OS provides two buttons for sleep
function. One is the Power On button and the other is the
Sleep Button. °Fn+F4” is assigned as the Sleep
button in ACPI mode. User can set the action of the Sleep
Button on the Power Management property.
Fn+F5
Display toggle
The Hotkey, Display Toggle, is to change the display type
at run-time. Possible display types are LCD, CRT and
Both. It can not detect the CRT, even when the CRT is not
connected. Press Hotkey can force to switch to CRT. This
Hotkey cannot switch the display to TV at DOS.
Fn+F6
Screen blank
This key will cause the LCD back light to be turned off.
This provides both a quick security feature and some
power savings. The LCD back light can also be turned off
via an APM timer. The LCD back light will be turned on
again when any of the following events occur:
T
Any key pressed
T
Pointing device movement
USB Device does not need to support.
Fn+F7
Touchpad toggle
This key will cause the internal touchpad pointing device
to be disabled. This is to prevent accidental system wakeups from standby. Pressing this key a second time will reenable the touch pad pointing device. BIOS check Internal
AuxDev ifnot exist then BIOS empty return.
Fn+F8
Speaker toggle
This key will cause the audio output to the speakers to
muted or disabled. Pressing this key a second time will reenable the audio output to the speakers.
Fn+w
Volume up
Increases the speaker volume.
Fn+y
Volume down
Decreases the speaker volume.
Fn+x
Brightness up
Increases the screen brightness.
Fn+z
Brightness down
Decreases the screen brightness.
NOTE: When activating hotkeys, press and hold the Fn key before pressing the other key in the hotkey
combination.
Chapter 1
27
Windows Keys
The keyboard features two keys that perform Windows-specific functions.
Key
Windows logo key
Description
Pressed alone, this key has the same effect as clicking on the
Windows Start button; it launches the Start menu. It can also be
used with other keys to provide a variety of functions:
+ Tab (Activates the next Taskbar button)
+ E (Opens the My Computer window)
+ F1 (opens Help and Support)
+ F (opens the Find: All Files dialog box)
+ M (minimizes all windows)
j + Windows logo key + M (undoes the minimize all windows
action)
+ R (opens the Run dialog box)
Application key
28
This key has the same effect as clicking the right mouse button; it
opens the application’s context menu.
Chapter 1
Euro key
Your computer supports the new Euro currency character. First, hold down the Alt Gr key, and then press the
Euro key.
Chapter 1
29
Touchpad
The build-in touchpad is a PS/2 compatible pointing device that senses movement on its surface.
The cursor responds to your finger movements on the touchpad. In addition, the two click buttons provide
the same functionality as a computer mouse, while the scroll key enables easy up and down scrolling in
documents and web pages.
The touchpad is located in the middle of the palm rest area, providing maximum comfort and efficiency.
Touchpad Basics
Use the touchpad as follows:
T
Slide your finger over the surface of the touchpad to control the movement of the cursor. Tap the
touchpad to perform selection and execution functions.
T
Press the left (1) and right (3) buttons to perform selection and execution functions, just as you
would use the buttons on a computer mouse.
T
Use the scroll key (2) to scroll through long documents and web pages. Press the top of the key to
scroll up, and the bottom to scroll down; left to scroll left, and right to scroll right.
Function
30
Left Button
Righ Button
4-Way Scroll Way
Tap
Execute
Click twice quickly
Tap twice (at the
same speed as
double-clicking the
mouse button)
Select
Click once
Tap once
Chapter 1
Function
Drag
Left Button
Righ Button
4-Way Scroll Way
Click and hold.
Then slide your
finger across the
touchpad to drag
the cursor over the
selection.
Tap
Tap twice quickly.
On the second tap,
slide your finger
across the
touchpad to drag
the cursor over the
selection.
Access
context
menu
Click once
Scroll
Click and hold the
up/down/left/right
button
NOTE: Keep your fingers, as well as the surface of the touchpad dry and clean. The touchpad is sensitive to
your finger movements: the lighter the touch, the better the response. Tapping hard will not increase the
touchpad’s responsiveness.
Chapter 1
31
Launch Keys
Located at the top of the keyboard are four buttons, in addition to the power button. These buttons are
called launch keys. They are designed as key 1, key 2, key 3 and key 4, from right to left. By default,
key 1 is used to launch the email application and key 2 is used to launch the Internet browser. Key 3
and key 4 start the Launch Manager application. The first four launch keys can be set by the user. To set
the launch keys, run the Acer Launch Manager.
Aspire 2010
#
32
Aspire 2020
Description
Email
Launches your email application.
Web browser
Launches your Internet browser
P1
User-programmable
P2
User-programmable
Chapter 1
Hardware Specifications and Configurations
Processor
Item
Specification
CPU type
Intel Centrino
CPU package
uFCPGA package
CPU core voltage
Support automatic selection of power supply voltage
CPU I/O voltage
1.05V
®
TM
mobile Pentium M processor at 1.4~ 1.8 GHz
BIOS
Item
Specification
BIOS vendor
Insyde
BIOS Version
Insyde MobilePRO BIOS 1.0
BIOS ROM type
Flash ROM
BIOS ROM size
512KB
BIOS package
32 lead of TSSOP
Bupported protocols
ACPI 1.0b,PC Card 95, SM BIOS 2.3, EPP/IEEE 1284, ECP/IEEE
1284 1.7 & 1.9, PCI 2.2, PnP 1.0a, DMI 2.0, USB, VGA BIOS, CDROM bootable
BIOS password control
Set by setup manual
Second Level Cache
Item
Cache controller
Specification
Built-in CPU
Cache size
1MB or 2MB
1st level cache control
Always enabled
2nd level cache control
Always enabled
Cache scheme control
Fixed in write-through
System Memory
Item
Specification
Memory controller
Intel 855GME
Memory size
128MB/256MB/512MB/1GB
DIMM socket number
2 sockets
Supports memory size per socket
1024MB
Supports maximum memory size
2GB (by two 1024MB SO-DIMM module)
Supports DIMM type
DDR Synchronous DRAM
Supports DIMM Speed
333MHz
Supports DIMM voltage
2.5V
Supports DIMM package
200-pin SO-DIMM
Memory module combinations
You can install memory modules in any combinations as long as
they match the above specifications.
Chapter 1
33
Memory Combinations
Slot 1
Slot 2
Total Memory
256/512MB
0 MB
256MB/512MB
256/512MB
256MB
512MB/768MB
256/512MB
512MB
768MB/1024MB
NOTE: Above table lists some system memory configurations. You may combine DIMMs with various
capacities to form other combinations.
.
LAN Interface
Item
Specification
Supports LAN protocol
10/100 Mbps (Aspire 2010)
10/100/100 Mbps (Aspire 2020)
LAN connector type
RJ45
LAN connector location
Rear side
.
Modem / Bluethooth Interface
Item
Specification
Data modem data baud rate (bps)
56K
Supports modem/bluetooth protocol
V.92 for MDC / Bluetooth 1.1 standard for BT
modem
Modem connector type
RJ11
Modem connector location
Rear side
Hard Disk Drive Interface
Item
34
Specification
VENDOR
MODEL NAME
HITACHI
IC25N0X0AT
MR04-0
HITACHI
HTS428060
F9AT00
HITACHI
HTS5480X0
M9AT00
TOSHBIA
MKX025GAS
TOSHIBA
MK6026GAX
SEAGATE
ST94019A
CAPACITY
(GB)
30/40/60/80
60
60/80
40/60
60
40
DISK HEAD
2/2/3/4
3
3/4
2/3
3
2
DISK
1/1/2/2
2
2/2
1/2
2
1
SPINDLE RPM
4200
4200
5400
4200
5400
4200
CACHE
BUFFER (MB)
2/2/8/6
8
8
8/8
16
2
INTERFACE
MODE
ULTRA DMA
100
ULTRA
DMA 100
ULTRA DMA
100
ULTRA DMA
100
ULTRA DMA
100
ULTRA DMA
100
DC REQUIRE
5V +/- 5%
5V +/- 5%
5V +/- 5%
5V +/- 5%
5V +/- 5%
5V +/- 5%
Chapter 1
Optical Drive Interface
Item
Specification
Vendor & model name
Panasonic
Model
Aspire 2010
Aspire 2020
Optical Media Drive
DVD/CD-RW combo drive
DVD Dual Drive
DVD-Super Multi Drive
DVD/CD-RW Combo Drive
Disc Performance
compatibility
Optical Drive Options:
Slot-loading optical drive options
T
DVD/CD-RW combo drive
T
T
T
T
Read: 8X DVD-ROM, 24X
CD-ROM
Write: 24X CD-R, 10X CDRW
Slot-loading DVD-Super Multi
Drive
T
DVD-Dual Drive
T
T
Read: 4X DVD+R, 4X
DVD+RW, 4X DVD-R, 4X
DVD-RW, 8X DVD-ROM,
24X CD-ROM
Write: 2.4X DVD+R, 2.4X
DVD-RW, 2X DVD-R, 2X
DVD-RW, 16X CD-R, 10X
CD-RW
T
T
Slot-loading DVD/CD-RW
combo drive
T
T
Data Buffer Capacity
2 MBytes
Interface
IDE ( ANSI ATA/ATAPI-5)
Read: 4X DVD-R, 4X
DVD-RW, 4X DVD+R, 4X
DVD+RW, 8X DVD-ROM,
24X CD-ROM, 2X DVDRAM
Write:2.4X DVD+R, 2.4X
DVD+RW, 4X DVD-R, 2X
DVD-RW, 16X CD-R, 8X
CD-RW, 2X DVD-RAM
Read: 8X DVD-ROM, 24X
CD-ROM
Write: 24X CD-R, 10X
CD-RW
Read Function
Applicable Discs
CD-ROM Mode 1
CD-ROM XA
CD-Audio
Mixed Mode CD-ROM (Audio and
Data Combined)
Photo-CD (Single and Multisession)
CD-I, Video CD
CD Plus/ CD Extra, CD-Text
CD-R disc
CD-RW disc
DVD-ROM single Layer 4.7GB,
dual Layer 8.5GB
DVD-R: 3.95/4.7GB
DVD-RW: 4.7GB
DVD-RAM: 2.6/4.7GB
Write Function
Applied Format
CD-ROM Mode-1
CD-ROM XA
CD-Audio
Mixed Mode (Audio and Data Combined)
CD-I, Video CD
CD-Plus / CD-Extra , CD-Text
Writing Method
Disc at once (DAO)
Session at once (SAO)
Track at once (TAO)
Variable packet writing
Fixed packet writing
Multi-session
Chapter 1
35
Optical Drive Interface
Item
Loading mechanism
Specification
Load: The disc can be loaded semi-automatically ( To load the disc in the
drive, it is needed to push the disc manually)
Unload: The disc can be unloaded automatically by motor powered
mechanism. The disc unloading can be operated by the Eject button or
Eject Command through the IDE interface.
Power Requirement
Input Voltage
+5V ± 5 % Ripple Less than 100mVp-p
Audio Interface
Item
Specification
Audio Controller
Realtek ALC250, AC97 Codec
Audio onboard or optional
Built-in, support CD playback when system off
Mono or Stereo
Stereo
Resolution
20 bit stereo Digital to analog converter
18 bit stereo Analog to Ditial converter
Compatibility
Microsoft PC99, AC97 2.2 & WHQL
Mixed sound source
CD
Sampling rate
48 KHz
Internal microphone
Yes
Internal speaker / Quantity
Yes / 2
Video Interface
Item
Specification
Video vendor
ATI
Video name
M11P
Chip voltage
Core/1.5V
Supports ZV (Zoomed Video) port
No
Video Resolution Mode (for both LCD and CRT)
Resolution
16 bits (High color)
32 bits (True color)
1024*768
Yes
Yes
1400*1050 (SXGA)
Yes
Yes
1600*1200 (UXGA)
Yes
Yes
1280*1024 (Monitor)
Yes
Yes
Parallel Port
Item
Parallel port controller
36
Specification
Intel ICH4-M
Number of parallel port
One
Location
Rear side
Connector type
25-pin D-type connector, in female type
Chapter 1
Parallel Port
Item
Specification
Parallel port function control
Enable/Disable/Auto (BIOS or operating system chooses
configuration) by BIOS setup
Note: Depending on your operating system, disabling an unused
device may help free systen resources for other devices.
Supports ECP/EPP/Bi-directional
(PS/2 compatible)
Yes (set by BIOS setup)
Note: When Mode is selected as EPP mode, “3BCh” will not be
available.
Optional ECP DMA channel (in
BIOS setup)
DMA channel 1
Optional parallel port I/O address
(in BIOS setup)
378h, 278h
Optional parallel port IRQ (in
BIOS setup)
IRQ7, IRQ5
USB Port
Item
Specification
USB compliancy level
2.0
OHCI
USB 2.0
Number of USB port
3
Location
Rear side
Serial port function control
Enable/Disable by BIOS setup
PCMCIA Port
Item
Specification
PCMCIA controller
ENE CB1410 CardBus
Supports card type
Type II
Number of slots
One type-II
Access location
Left panel
Supports ZV (Zoomed Video) port
No ZV support
Supports 32 bit CardBus
Yes
System Board Major Chips
Item
System core logic
Controller
Intel 855GME and ICH4-M
Super I/O controller
SMSC LPC47N217, LPC bus
Audio controller
Realtek ALC202A Codec
Video controller
ATI M11-P
Hard disk drive controller
ICH4-M
Keyboard controller
ENE KB910
RTC
ICH4-M
Chapter 1
37
Keyboard
Item
Specification
Keyboard controller
ENE KB910
Keyboard vendor & model name
Standard keyboard w/o launch button embeded
Total number of keypads
84/85/88 keys with 101/102 key emulation
inverted “T” cursor layout ; 3mm(minimum) key travel
Windows logo key
Yes
Internal & external keyboard work
simultaneously
Yes
Battery
Item
Specification
Vendor & model name
Samsung
Battery Type
Li-ion
Pack capacity
64 Whr
Cell voltage
3.7V/cell
Number of battery cell
8
Battery Charge
5-hour battery life for 8-cell battery
2-hour quick-charge time; 3.5-hour charge-in-use
Adapter
65W AC Adapter
LCD Inverter Specification
No.
Supplier
Model
Type
1
LG
LP154W01-A3
15.4”WXGA
2
Samsung
LTN154X1-L02
15.4” WXGA
3
AU
B154EW01
15.4” WXGA
4
QDI
5TL02
15.4” WXGA
LCD
Item
Vendor & model name
Specification
Samsung
LTN154X1-L02
LG
LP154W01-A3
QDI
5TL02
AU
B154EW01
LCD display area
(diagonal, inch)
15.4”
15.4”
15.4”
15.4”
Display technology
TFT
TFT
TFT
TFT
Resolution
WXGA
(1280* 800)
WXGA
(1280* 800)
WSXGA
(1280* 800)
WSXGA
(1280* 800)
Supports colors
262K
262K
262K
262K
Brightness control
keyboard
hotkey
keyboard
hotkey
keyboard
hotkey
keyboard
hotkey
Contrast control
No
No
No
No
Mechanical Specifications
Optical Specification
38
Chapter 1
LCD
Item
Suspend/Standby control
Specification
Yes
Yes
Yes
Yes
Supply voltage for LCD
display (V)
3.3
3.3
3.3
3.3
Supply voltage for LCD
backlight (Vrms)
690
690
690
690
Electrical Specification
AC Adapter
Item
Vendor & model name
Specification
Delta ADP-65DB
Liteon PA-1650-02CR
Input Requirements
Maximum input current (A,
@100Vac, full load)
1.5A max@3.5A/100Vac and 240 Vac
Nominal frequency (Hz)
47 - 63
Frequency variation range
(Hz)
47 - 63
Nominal voltages (Vrms)
90 - 264
Inrush current
The maximum inrush current will be less than 50A and 100A when
the adapter is connected to 100Vac(60Hz) and 240Vac(50Hz)
respectively.
Efficiency
High efficiency 85% minimum, at 100~240Vac AC input, full load,
warm-up condition.
Output Ratings (CV mode)
DC output voltage
Offers constant voltage 19.0V output source with 65W max output
power capacity.
Noise + Ripple
300mvp-pmax (20MHz bandwidth) for resistor load
Output current
0 A (min.)
3.5A (max.)
Output Ratings (CC mode)
DC output voltage
18.0 ~ 20.0
Constant output
3.5A
Dynamic Output Characteristics
Start-up time
3 sec. (@115 Vac and 230Vac full load)
Hold up time
5ms min. (@115 Vac input, full load)
Over Voltage Protection
(OVP)
25V
Short circuit protection
Output can be shorted without damage, and auto recovery
Electrostatic discharge
(ESD)
15kV (at air discharge)
8kV (at contact discharge)
Dielectric Withstand Voltage
Primary to secondary
4242 Vdc for 1 second
Leakage current
60uA at 240Vac/60Hz
Regulatory Requirements
1. FCC class B requirements (USA)
2. VDE class B requirements (German)
3. VCCI classII requirements (Japan)
Chapter 1
39
Power Management
ACPI Mode
Power Management
Mech. Off (G3)
All devices in the system are turned off completely.
Soft Off (G2/S5)
OS initiated shutdown. All devices in the system are turned
off completely.
Working (G0/S0)
Individual devices such as the CPU and hard disk may be
power managed in this state.
Sleeping State (S3)
CPU Power Down
VGA Power Down
PCMCIA Suspend
Audio Power Down
Hard Disk Power Down
Super I/O Power Down
Sleeping State (S4)
Also called Hibernate state. System saves all system
states and data onto the disk prior to power off the whole
system.
Environmental Requirements
Item
Specification
Temperature
Operating
+5 ~ +35°C
Non-operating
-20 ~ +65°C
Non-operating
-20 ~ +65°C (storage package)
Humidity
Operating
10% to 90% without condensation
Non-operating
10% to 90% RH, non-condensing (unpacked)
Non-operating
10% to 90% RH, non-condensing (storage package)
Vibration
Operating (unpacked)
5 ~ 500Hz: 0.9G
Non-operating (unpacked)
5 ~ 500Hz: 1.3G
Mechanical Specification
Item
40
Specification
Dimensions
360mm (W) x 273mm (D) x 28-33.49mm (H)
(14.2x10.7x1.1-1.32 inches)
NOTE: The size and weight of individual units may vary depending
on configuration.
Weight
3 kg (6.6lbs)
NOTE: The size and weight of individual units may vary depending
on configuration.
I/O Ports
Three USB 2.0 Ports, one IEEE 1394 port, one Ethernet (RJ-45) port ,
one Modem (RJ-11) port, one S-video/TV-out(NTSC/PAL) port, one
Parallel port, one External display (VGA) port, one Microphone/line-in
jace, one Headphone/speaker/line-out jack, one Infrared (FIR) port,
one PC card slot (type II), one DC-in jack for AC adapter
Drive Bays
One
Chapter 1
Mechanical Specification
Item
Specification
Material
Recycle plastic PC+ABS 94V0
Indicators
Power, Media activity, Battery charge, Wireless/Bluetooth
communication, Caps lock, Pad lock, Num lock and Scroll lock
indicators
Switch
Power switch
Lid switch
Touch pad Left/Right
Chapter 1
41
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However,
if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press m during POST (when “Press <F2> to enter Setup” message is prompted
on the bottom of screen).
The setup screen displays BIOS as follows:Navigating the BIOS Utility
Function
Item
Screen
Display system information
Main
Set Date and Time
Enable/Disable Quiet Boot Logo
Enable/Disable LCD Auto DIM
Enable/Disable Network Boot
Enable/Disable F12 Boot Menu
Advanced
Allow users to set FIR ports
Allow users to set LPT ports
Allow users to enable/disable legacy USB
Security
Set User passwords
Set Supervisor passwords
Enable/Disable HDD Drive Lock
Enable/Disable Password on Boot
Boot
Allow users to change boot up devices priorities
Exit
Exit and save settings
There are five menu options: Main, Advanced, Security, Boot and Exit.
Follow these instructions:
T
To choose a menu, use the cursor left/right keys (zx).
T
To choose a parameter, use the cursor up/down keys ( wy).
T
To change the value of a parameter, press p or q.
T
Press ^ while you are in any of the menu options to go to the Exit menu.
T
In any menu, you can load default settings by pressing t. You can also press u to save any
changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values.
Chapter 2
42
Insyde Software SCU
5:40:09 AM
May 20, 2003
Main
Advanced
Security
----Devices--------------------------------------------------Product Name = Aspire 2010
Manufacture Name = Acer
System BIOS Version = V1.00
VGA BIOS Version =
Boot
Exit
-----System-----------------------CPU = Intel® Pentium ® M
CPU Speed = 1600 MHz
HDD Model Name = HITACHI_DK23EA-40
----Memory-----------------------
HDD Serial Number = 8D4648
ATAPI Model Name= UJDA740 DVD/CDROM
Base Memory = 640 KB
Serial #: ( 32 bytes)
Extended Memory = 255MB
Asset Tag#: (32 bytes)
VGA Memory = 64 MB
UUID = (16 bytes)
Setup system date, time. Enable boot logo and get system information.
Parameter
43
Description
Product Name
This field will show product name.
Manufacture Name
This field will show manufacturer name.
System BIOS Version
This field reports the BIOS version of system.
VGA BIOS Version
This field reports the VGA version of the system.
Hard Disk Mode Name
This item will show the size of HDD installed on
Primary IDE master. The hard disk size is
automatically detected by the system. If there is no
hard disk present or unknown type, “None” should
be shown on this field.
HDD Serial Number
This item allows the serial number of the Hard Disk.
If there is no hard disk present or unknown type,
“None” should be shown on this field.
ATAPI
This item will show the model name of DVD/CDROM drive installed on system. The DVD/CD-ROM
model name is automatically detected by the
system. If there is no DVD/CD-ROM model present
or unknown type, “None” should be shown on this
field.
Serial Number
This item will show the Serial number of system.
Asset Tag
This item will show the Asset Tag number of the
system.
UUID
This number only valid when there is an internal LAN
device presents, otherwise, zero will be display in
this field.
System
First field reports the model name of processor.
Second field reports CPU Speed.
Chapter 2
Memory
Parameter
Description
Base
This field reports the base memory size of system.
Extended
This field reports the extended memory size of the
system.
VGA BIOS Version
This field reports the VGA BIOS version of system.
Chapter 2
44
Main
This menu provides you the information of the system.
Insyde Software SCU
Main
Advanced
May 20, 2003 5:40:09
Boot
Security
Exit
Date and Time
ԩ Quiet Bootʳ
ԩʳ ʳ LCD Auto DIMʳ˲
----------------------------Date and Time------------------------
ԩ Network Boot
Day
20
Hour
8
˲F12 Boot Menu
Month
5
Minute
35
2003
Second
9
Year
OK
Cancel
<Tab> <Right> <Left> for block select. <Up> <Down> for item select.
< Enter> for accept. <Cancel> <Esc> for reject. <Alt> activates accelerators.
<Space> for Enable or Disable.
Parameter
45
Description
Date and Time
The hours are displayed with 24 hours format. The values set in these two fields
take effect immediately.
Quiet Boot
Customer Logo display will be shown during POST when it is selected.
LCD Auto DIM
When this is selected, brightness of the LCD will be reduced for power saving
when adaptor has been removed from the system.
When this is not selected, brightness of the LCD will remain the same after
adaptor has been removed from the system.
Network Boot
When this is selected, Boot from LAN feature is enabled. When this is not
selected, Boot from LAN feature is then disabled.
F12 Boot Menu
When this is selected, users can modify device boot priority by pressing F12 key
during POST. When this is not selected, device boot priority will not be
adjustable during POST.
Chapter 2
Quiet Boot
Custormer Logo display will be shown during POST when it is selectd.
Insyde Software SCU
Main
Advanced
Security
May 20, 2003 5:40:09
Boot
Exit
ʳ ʳ Date and Time
ʳԩ
ʳ Quiet Bootʳ
ԩʳ
ԩʳʳ ʳ LCD Auto DIMʳ˲
˲ʳ ʳNetwork Boot ʳ˲
ԩ
˲F12 Boot Menuʳ
ԩ
ԩ
Display big boot logo on screen when system is booting.
<Space> for Enable or Disable.
F12 Boot Menu
When this is selected, users can modify device boot priority by pressing F12 key during POST. When this
is not selected, device boot priority will not be adjustable during POST. Default is disabled.
Insyde Software SCU
Advanced
ʳ ʳ Main
Security
May 20, 2003 5:40:09
Boot
Exit
ʳ ʳ Date and Time
ԩʳ ʳ
ԩʳ ʳ Quiet Boot
˲ʳ ʳ
ʳ˲ ʳ
˲ʳ ʳ LCD Auto DIMʳ˲
ԩ
ԩ Network Boot
ԩ
ԩF12 Boot Menu
Enable or disable lan boot function, <Space> for Enable or Disable.
Chapter 2
46
˲
LCD Auto DIM
When this is selected, brightness of the LCD will be reducted for power savind when adaptor has been
removed from the system.
When this is not selected, brightness of the LCD will remain the same after adaptor has been removed
from the system.
Insyde Software SCU
Main
Advanced
Security
May 20, 2003 5:40:09
Boot
Exit
ʳ ʳ Date and Time
ԩʳ ʳ Quiet Boot
˲ʳ ʳ LCD Auto DIMʳ˲ ʳ
ԩ Network Boot
ԩF12 Boot Menu
Enable or disable the F12 key for Boot Menu during Post
<Space> for Enable or Disable.
Network Boot
When this is selected, Boot from LAN feature is enabled. When this is not selected, Boot from LAN feature
is then disabled.
Insyde Software SCU
Main
Advanced
Security
May 20, 2003 5:40:09
Boot
Exit
ʳ ʳ Date and Time
ԩʳ ʳ Quiet Boot
˲ʳ ʳ LCD Auto DIMʳ˲
ԩ Network Bootʳ
ԩF12 Boot Menu
Enable or disable auto dim function, <Space> for Enable or Disable.
47
Chapter 2
Advanced
The Advanced screen contains parameters involving your hardware devices. It also provides advanced
settings of the system.
FIR Ports
Configure the system’s infrared port using options: Disabled and Enabled.
Insyde Software SCU
Main
Advanced
Infrared Ports(FIR)
Parallel Port(LPT)
ԩLegacy USB support
May 20, 2003 5:40:09
Security
Boot
Exit
---------------------------------FIR Ports------------------------------------FIR I/O settings---
-Mode Setting for IRDA-
( ) Disabled
( ) COM1,3F8,IRQ4
( ) Normal (16550)
( ) IrDA (HPSIR)
( ) COM2,2F8,IRQ3
( ) ASK IR
( ) COM3,3E8,IRQ4
(Ԧ) FAST IR
(Ԧ) COM4,2E8,IRQ3
--DMA Setting For Fast IR-( ) DMA1
( ) DMA2
( ) DMA3
OK
Cancel
<Tab> <Right> <Left> for block select. <Up> <Down> for item select.
< Enter> for accept. <Cancel> <Esc> for reject. <Alt> activates accelerators.
<Space> for Enable or Disable.
The table below describes the parameters in the screen. Settings in boldface are the default and suggested
parameter settings.
Description
Option
FIR I/O Settings
Sets the base I/O address and IRQ for
Infrared port.
COM1, 3F8, IRQ4/ COM2,
2F8, IRQ3/ COM3, 3E8,
IRQ4/ COM4, 2E8, IRQ3
DMA Setting for Fast
ԩ
IR
Sets a DMA channel for the printer to
operate in ECP mode. This parameter is
enabled only if Mode is set to ECP.
DMA1, DMA2, DMA3,
Mode Setting
Chapter 2
Normak (16550), IrDA
(HPSIR), ASK IR, FAST IR
48
LPT Port
Configure the system’s parallel port using options: Disabled and Enabled.
LPT Sub menu:
Insyde Software SCU
Main
Advanced
Security
May 20, 2003 5:40:09
Boot
Exit
\
---------------------------------FIR Ports------------------------------------Port Address-------
-------Port Definition------------
( ) None
( ) Standard AT (Centronics)
Parallel
Port(LPT)
(Ԧ) LPT1, 378, IRQ7
( ) Bidirectional (PS-2)
( ) LPT2, 278, IRQ5
( ) Enhanced Parallel (EPP)
ԩLegacy USB
( ) LPT3, 3BC, IRQ7
(Ԧ) Extended Capabilities(ECP)
Infrared
Ports(FIR)
--DMA Setting For Fast IR-(Ԧ) DMA1
( ) DMA3
OK
Cancel
The table below describes the parameters in the screen. Settings in boldface are the default and
suggested parameter settings.
49
Description
Option
Port Address
Sets the base I/O address for the parallel
port. When Mode is selected as EPP mode,
“3BC” will not be available.
None/ LPT1, 378, IRQ7/
LPT2, 278, IRQ5/ LPT3, 3BC,
IRQ7
Port Definition
Sets the mode for the parallel port.
Standard AT: Normal mode (AT compatible)
Bi-directional: Bi-directional mod (PS/2
compatible)
Enhanced Parallel (EPP): EPP mode
Extended Compabilities (ECP): ECP mode
(requires DMA channel)
Standard AT (Centronics),
Bidirectional (PS-2),
Enhanced Parallel (EPP),
Extended Capabilities(ECP)
DMA Setting for Fast
IR
If ECP mode has been selected, then DMA
default is DMA1.
DMA1, DAM3
Chapter 2
Legacy USB Support
g y
Insyde Software SCU
Main
Advanced
Security
May 20, 2003 5:40:09
Boot
Exit
\
Infrared Ports(FIR)
Parallel Port(LPT)
ԩLegacy USB
( ) DMA1
Legacy USB keyboard Floppy Disk USB Mouse Support
<Space> for Enable or Disable
Option
Description
Disabled
Disable support for Legacy Universal Serial Bus
Enabled
Enable support for Legacy Universal Serial Bus.
Chapter 2
50
Security
The Security screen contains parameters that help safeguard and protect your computer from
unauthorized use.
Insyde Software SCU
Main
Advanced
Security
Set Supervisor Password
May 20, 2003 5:40:09
Boot
Exit
Set User Password
Lock HardDisk Drive
Password On boot
------------Set Supervisor password---------------Enter old Supervisor password:
..........
Enter new Supervisor Password:
..........
Verify new Supervisor Password:
..........
OK
Cancel
Enter new password. Password will NOT be displayed
The table below describes the parameters in this screen. Settings in boldface are the default and
suggested parameter settings.
Set Supervisor/User Password
If password on boot is required, the password must be set otherwise it cannot be enabled.
The formats of the password are as follows:
Length
No more than 8 characters
Characters
0-9,A-Z (not case sensitive)
Parameter
51
Description
Set User Password
Press Enter to set the user password.
When set, this password protects the
BIOS Setup Utility from unauthorized
access.
Set Supervisor Password
Press Enter to set the administrator
password. When set, this password
protects the BIOS Setup Utility from
unauthorized access.
Option
Length -- No more than 8
characters
Characters -- 0-9, A-Z (not
case sensitive)
Chapter 2
Parameter
Description
Option
Lock Hard Disk Drive
This feature is available to user when
Supervisor password is set. Password
can be written on HDD only when
Supervisor password or user password is
set and password onHDD is set to
enabled. Supervisor Password is written
to HDD when only Supervisor password
is being set. User password is written to
HDD when both passwords are set.
When both Supervisor and user
passwords are present, both passwords
can unlock the HDD.
Disabled/Enabled
Password on Boot
Defines whether a password is required
or not while the events defined in this
group happened. The following suboptions are all requires the Supervisor
password for changes and should be
grayed out if the user password was used
to enter setup.
Allows the user to specify whether or not
a password is required to boot.
Check
Uncheck
Chapter 2
52
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable
devices includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM
in module bay and onboard LAN device.
Insyde Software SCU
Main
Advanced
May 20, 2003 5:40:09
Boot
Security
Exit
Boot Device
---------------------------------------Boot Device--------------------------------------
[
---1st Boot Device---
---2nd Boot Device---
--3rd Boot Device----
( ) Hard Drive
( ) CD-ROM/DVD
Drive
(Ԧ) Floppy Drive
( ) Network Boot
(Ԧ) Hard Drive
( ) CD-ROM/DVD
Drive
( ) Floppy Drive
( ) Network Boot
( ) Hard Drive
(Ԧ) CD-ROM/DVD
Drive
(ʳ ʳ ) Floppy Drive
( ) Network Boot
] USB Mass storage
OK
Cancel
<Tab> <Right> <Left> for block select. <Up> <Down> for item select.
< Enter> for accept. <Cancel> <Esc> for reject. <Alt> activates accelerators.
<Space> for Enable or Disable.
.
53
Chapter 2
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
Insyde Software SCU
Main
Advanced
May 20, 2003 5:40:09
Security
Boot
Exit
Exit Saving Changes
--------------Exit Saving Changes------------------- Exit Discarding Changes
Press <OK> to save the current
Setup parameters to CMOS RAM.
Load Setup Default
Discard Changes
The system will reboot !!!
OK
Cancel
<Tab> <Right> <Left> for block select. <Up> <Down> for item select.
< Enter> for accept. <Cancel> <Esc> for reject. <Alt> activates accelerators.
<Space> for Enable or Disable.
The table below describes the parameters in this screen.
Parameter
Description
Exit Saving Changes
Allows the user to save changes to CMOS and reboot the system.
Exit Discarding
Changes
Allows the user Discards changes made and exits System Setup.
Load Setup Default
Loads default settings for all parameters (same as t ).
Discard Changes
Allows the user to discard previous changes in CMOS Setup.
Chapter 2
54
Exit Discarding Changes
Exit without saving current settings.
Insyde Software SCU
Main
Advanced
May 20, 2003 5:40:09
Boot
Exit
Exit Saving Changes
Security
--------------Exit Discarding Changes-----------Press <OK> to Exit the SCU.
Load Setup Default
The current settings will not be saved!!!
OK
Exit Discarding Changes
Discard Changed
Cancel
<Tab> <Right> <Left> for block select. <Up> <Down> for item select.
< Enter> for accept. <Cancel> <Esc> for reject. <Alt> activates accelerators.
<Space> for Enable or Disable.
Load Setup Default
Load manufacture default settings.
Insyde Software SCU
Main
Advanced
May 20, 2003 5:40:09
Boot
Exit
Exit Saving Changes
Security
----------------Load Setup Default----------------Do you wish to change the current setup
to the system default values?
OK
Exit Discarding Changes
Load Setup Default
Discard Changed
Cancel
<Tab> <Right> <Left> for block select. <Up> <Down> for item select.
< Enter> for accept. <Cancel> <Esc> for reject. <Alt> activates accelerators.
<Space> for Enable or Disable.
55
Chapter 2
Discard Changes
Restore current settings to original settings.
Insyde Software SCU
Main
Advanced
May 20, 2003 5:40:09
Boot
Exit
Exit Saving Changes
Security
----------------Discard Changes-------------------Do you wish to restore the current setup
to the original custom values?
OK
Exit Discarding Changes
Load Setup Default
Discard Changed
Cancel
<Tab> <Right> <Left> for block select. <Up> <Down> for item select.
< Enter> for accept. <Cancel> <Esc> for reject. <Alt> activates accelerators.
<Space> for Enable or Disable.
Chapter 2
56
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
T
New versions of system programs
T
New features or options
T
Restore a BIOS when it becomes corrupted.
Use the Flash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery
Diskette before you use the Flash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Flash utilities.
NOTE: Please use the AC adaptor power supply when you run the Flash utility. If the battery pack does
not contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not
completely loaded.
Fellow the steps below to run the Flash.
1.
Prepare a bootable diskette.
2.
Copy the Flash utilities to the bootable diskette.
3.
Then boot the system from the bootable diskette. The Flash utility has auto-execution function.
System Diagnostic Diskette
This diagnostic diskette is for the Acer Aspire 2010/2020 series notebook machine. However, system
diagnostic utility is not ready as service CD released. Acer HQ CSD will upload the utility to CSD website
as soon as it is ready.
57
Chapter 2
Chapter 3
Machine Disassembly and Replacement
This chapter contains step-by-step procedures on how to disassemble the notebook computer for
maintenance and troubleshooting.
To disassemble the computer, you need the following tools:
T
Wrist grounding strap and conductive mat for preventing electrostatic discharge
T
small Philips screwdriver
T
flat head screwdriver
T
Philiips screwdriver
T
nut screwdriver
T
tweezers
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
When you remove the stripe cover, please be careful not to scrape the cover.
NOTE: This chapter will base on Aspire 2000 to modify. If you need to read the mpeg files please refer to
Aspire 2000 Service CD, and the P/N is VD.A20V5.001
Chapter 3
Aspire 2010/2020
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:
59
1.
Turn off the power to the system and all peripherals.
2.
Unplug the AC adapter and all power and signal cables from the system.
3.
Remove the battery pack.
Chapter 3
Disassembly Procedure Flowchart
Chapter 3
Aspire 2010/2020
Item
A
61
Description
M2.5x5
M2.0x4
B
M2.5x3
C
M2.5x4
D
M2.5x10
M2.5x4
E
M2.5x14
F
M2.0x4
G
M2.5x4
H
M2.5x14
I
M2.5x10
J
M2.5x5
K
M3.0x3
L
M2.0x3
M
2.5x4
N
M2.5x4
O
M2.5x5
P
M2.5x4
Chapter 3
Aspire 2010/2020 Disassembly Procedure
This section will guide you how to disassemble the system when you need to perform system service.
Please also refer to the disassembly video, if availabled.
CAUTION: Before you proceed,make sure you have turned off the system and all peripherals connected.
Disassemble the Battery and HDD
1.
Release the battery lock and slide the battery latch.
2.
Then remove the battery pack.
3.
Remove the two screws to release the hard drive door.Then take it away.
Disassemble the Wireless
1.
Remove the one screw to release the mini door, and take it away.
2.
Disconnect the two wireless cables.
3.
Then take the wireless board from the base.
Disassemble the RAM and ODD
1.
Remove the one screw to release the RAM door and remove it.
2.
Press down the both side latches to release the RAM board.
3.
Remove the one screw to release the ODD module.
4.
Then push the inner position to remove the ODD from the base.
5.
Pull the entire ODD moudle from the system.
Chapter 3
Aspire 2010/2020
Disassemble the Middle Cover Board
1.
Remove the one screw.
2.
Detach the middle cover from the unit with the flat screw driver.
3.
Disconnect the system cable from the middle cover board.
4.
Remove the two screws to release the middle cover board.
5.
Then detach the middle cover board from cover.
Disassemble the Keyboard
63
1.
Remove the screws on each side.
2.
Pull up both sides of the latches to disconnect the FFC from the mainboard.
3.
Remove the screws on each side to release the keyboard bracket.
4.
Then take the keyboard supporter bracket from the system.
Chapter 3
Disassemble the LCD
1.
Remove the one screw from the LVDS board.
2.
Pull the LCD coaxial board and the cable from the system.
3.
Remove the two screws from the hinge on each side to release the LCD panel.
4.
Pull the entire LCD module from the system.
Disassemble the MDC and RAM
1.
Remove the two screws to release the MDC board.
2.
Disconnect the MDC cable before you take the MDC board.
3.
Press down the both sides latches to release the RAM.
4.
Disconnect the right and left speaker cables from the mainboard.
5.
Disconnect the touchpad FPC connector and CPU fan cable.
Disassemble the Upper Case
1.
Remove the thirteen screws located on the base case.
2.
Remove the two screws on the other side to located on the rear panel.
3.
Remove the three screws to release the upper case.
4.
Detach the upper case from the system.
Chapter 3
Aspire 2010/2020
Disassemble the Main Unit ( Touchpad, Bluetooth and LCM Board)
1.
Remove the seven screws to release the touchpad supporter bracket.
2.
Disconnect the touchpad FPC connector.
3.
Disconnect the cable as highlights.
4.
Then detach the touchpad bracket from the position.
5.
Detach the touchpad PC from the module.
6.
Disconnect the bluetooth board FFC connector.
7.
Remove the two screws to release the bluetooth board.
8.
Take the bluetooth board from the system.
9.
Remove the one screw to release the LCM board.
10. Detach the LCM board from the system.
65
Chapter 3
Disassemble the Main Unit ( Speakers, Fan, Thermal and CPU)
1.
Remove the one screw to release the up hinge saddle.
2.
Remove the three screws to release the bottom hinge saddle.
3.
Detach the right hinge saddle from the case.
4.
Remove the two screws to release the right hinge saddle.
5.
Take the right speaker from the opsition.
6.
Remove the one screw to release the CPU fan from the hinge saddle.
7.
Take the CPU fan from the hinge saddle.
8.
Remove the three screws to release the left hinge saddle.
9.
Detach the left hinge saddle from the system.
10. Remove the one screw to release the left speaker from the base cover.
11. Then detach the left speaker.
12. Remove the four screws to release the thermal module.
13. Detach the thermal module from the system.
14. Remove the one screw to release the CPU.
15. Detach the CPU fan from the socket.
Chapter 3
Aspire 2010/2020
Disassemble the Main Unit ( VGA, Card Reader, Sub-Woofer and Mainboard)
1.
Remove the one screw to release the VGA bracket.
2.
Detach the VGA module from the mainboard.
3.
Separate the VGA bracket and the VGA board.
4.
Remove the ground screw to release the card reader.
5.
Disconnect the card reader cables on each side.
6.
Disconnect the sub-woofer cable
7.
Remove the screws on each side to release the sub-woofer.
8.
Detach the sub-woofer from the case.
9.
Detach the card reader board from the case.
10. Remove the one screw to release the mainboard.
11. Press the PCMCIA button and hold the position to release the mainboard from the case.
67
Chapter 3
Disassemble the LCD Module
1.
Remove the screws on each side.
2.
Detach the bezel from the LCD panel.
3.
Remove the screws located on the different side.
4.
Detach the LCD panel from the cover.
5.
Take the antenna away from the position to release the inverter board.
6.
Disconnect the LCD coaxial cables.
7.
Remove the four screws to release the left LCD bracket.
8.
Take the left LCD bracket from the panel.
9.
Remove the four screws to release the right LCD bracket.
10. Take the right LCD bracket from the panel.
Chapter 3
Aspire 2010/2020
Disassemble the ODD Module
1.
Remove the two screws to separate the ODD drive.
2.
Detach the ODD bracket.
3.
Detach the ODD door.
Disassemble the HDD Module
69
1.
Remove the two screws on each side.
2.
Separate the hard disk top cover and take the hard drive from the carrier.
3.
Remove the hard disk connector from the rear position.
Chapter 3
Chapter 4
Troubleshooting
Use the following procedure as a guide for computer problems.
1.
Obtain the failed symptoms in as much detail as possible.
2.
Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by
repeating the same operation.
3.
If any problem occurs, you can perform visual inspection before you fellow this chapter’s instructions.
You can check the following:
power cords are properly connected and secured;
there are no obvious shorts or opens;
there are no obviously burned or heated components;
all components appear normal.
4.
After you perform visual inspection you can also verify the following:
ask the user if a password is registered and, if it is, ask him or her to enter the password.
verify with the customer that Wndows XP is installed on the hard disk. Operating systems that
were not preinstalled by Acer can cause malfunction.
make sure all optional equipment is removed from the computer.
make sure the floppy disk is empty.
5.
Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified)
Go To
Power failure. (The power indicator does
not go on or stay on.)
“Power System Check”
POST does not complete. No beep or error
codes are indicated.
“Insyde MobilePro BIOS POST Beep Code
and POST Messages”
“Undetermined Problems”
POST detects an error and displayed
messages on screen.
“Insyde MobilePro BIOS POST Beep Code
and POST Messages”
Other symptoms (i.e. LCD display problems “Insyde MobilePro BIOS POST Beep Code
or others).
and POST Messages”
Symptoms cannot be re-created
(intermittent problems).
Chapter 4
Use the customer-reported symptoms and
go to “Insyde MobilePro BIOS POST Beep
Code and POST Messages” on page 67
“Intermittent Problems”
“Undetermined Problems”
70
System Check Procedures
External Diskette Drive Check
Do the following steps to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic
diskette is required.
NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause
damage to the drive or cause the drive to fail.
Do the following to select the test device.
1.
The FDD heads can become dirty over time, affecting their performance. Use an FDD cleaning kit to clean
the heads. If the FDD still does not function properly after cleaning, go to next step.
2.
Boot from diagnostic program.
3.
If an error occurs with the internal diskette drive, reconnect the diskette connector on the main board.
If the error still remains:
1.
Reconnect the external diskette drive module.
2.
Replace the external diskette drive module.
3.
Replace the main board.
External CD-ROM/DVD-ROM Drive Check
Do the following to isolate the problem to a controller, drive, or CD-ROM/DVD-ROM. Make sure that the CDROM does not have any label attached to it. The label can cause damage to the drive or can cause the drive
to fail.
Do the following to select the test device:
1.
Insert an audio CD into the CD/DVD drive. If the CD/DVD drive can read the data from the audio CD. The
drive does not have problem, then go to next step. If the CD/DVD LED on the front panel does not emit
light as it read the data from the audio CD, then go to next step. However, if the CD/DVD drive can not
read data from the audio CD, you may need to clean the CD/DVD drive with a CD/DVD drive cleaning
disk.
2.
Make sure that the appropriate driver has been installed on the computer for the CD/DVD drive.
3.
Boot from the diagnostics diskette and start the diagnostics program
4.
See if CD-ROM Test is passed when the program runs to CD-ROM/DVD-ROM Test.
5.
Follow the instructions in the message window.
If an error occurs, reconnect the connector on the main board. If the error still remains:
71
1.
Reconnect the CD-ROM/DVD-ROM module.
2.
Replace the CD-ROM/DVD-ROM module.
3.
Replace the main board.
Chapter 4
Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is to be tested.
If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable
extending from the keyboard is correctly seated in the connector on the main board.
If the keyboard cable connection is correct, run the Keyboard Test.
If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a
non-defective FRU:
1.
Reconnect the keyboard cables.
2.
Replace the keyboard.
3.
Replace the main board.
The following auxiliary input devices are supported by this computer:
T
Embedded Numeric Keypad
T
External keyboard
If any of these devices do not work, reconnect the cable connector and repeat the failing operation.
Memory Check
Memory errors might stop system operations, show error messages on the screen, or hang the system.
Currently, we do not provide memory test program. However, if you need to check memory but have no testing
program or diagonositc utility at hand, please go to http://www.passmark.com to download the shareware
“BurnIn Test V.3.0”. You may test the memory with this program under Window XP environment.
NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.
Power System Check
To verify the symptom of the problem, power on the computer using each of the following power sources:
1.
Remove the battery pack.
2.
Connect the power adapter and check that power is supplied.
3.
Disconnect the power adapter and install the charged battery pack; then check that power is supplied by
the battery pack.
If you suspect a power problem, see the appropriate power supply check in the following list:
Chapter 4
T
“Check the Power Adapter”
T
“Check the Battery Pack”
72
Check the Power Adapter
Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power
adapter cable. See the following figure
Pin 1: 19V
Pin 2: 0V, Ground
1.
If the voltage is not correct, replace the power adapter.
2.
If the voltage is within the range, do the following:
T
Replace the main board.
T
If the problem is not corrected, see “Undetermined Problems”.
T
If the voltage is not correct, go to the next step.
NOTE: An audible noise from the power adapter does not always indicate a defect.
73
3.
If the DC-IN indicator does not light up, check the power cord of the power adapter for correct continuity
and installation.
4.
If the operational charge does not work, see “Check the Power Adapter” .
Chapter 4
Check the Battery Pack
To check the battery pack, do the following:
From Software:
1.
Check out the Power Options in control Panel
2.
In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total
Battery Power Remaining are correct.
3.
Repeat the steps 1 and 2, for both battery and adapter.
4.
This helps you identify first the problem is on recharging or discharging.
From Hardware:
1.
Power off the computer.
2.
Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground).
3.
If the voltage is still less than 7.5 Vdc after recharging, replace the battery.
4.
If the voltage is within the normal range, run the diagnostic program.
To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50%
of the total power remaining when installed in the computer.
If the battery status indicator does not light up, remove the battery pack and let it return to room temperature.
Re-install the battery pack.
If the charge indicator still does not emit, replace the battery pack. If the charge indicator still does not light up,
replace the DC/DC charger board.
Touchpad Check
If the touchpad doesn’t work, do the following actions one at a time to correct the problem. Do not replace a
non-defective FRU:
1.
After rebooting, run Touch pad/PS2 Mode Driver.
2.
Run utility with the PS/2 mouse function and check if the mouse is working.
3.
If the PS/2 mouse does not work, then check if the main board to switch board FPC is connected well.
4.
If the main board to switch board FPC is connected well, then check if the touch pad FPC connects to the
main board properly.
5.
If there is still an error after you have connected the touch pad FPC to the main board properly, then
replace the touch pad or touch pad FPC. The touch pad or touch pad FPC may be damaged.
6.
Replace switch board.
7.
If the touch pad still does not work, then replace the FPC on Track Pad PCB.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement
can occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware
problem. No service actions are necessary if the pointer movement stops in a short period of time.
Display Check
1.
Connect an external display to the computer’s external monitor port, the boot the computer. The computer
can automatically detect the external display. Press Fn+ p to switch to the external display.
2.
If the external display works fine, the internal LCD may be damaged. Then perform the following steps:
Make sure the DDRRAM module is seated properly. Then run the diplay test again. If the problem
still exists, go to next step.
Replace the inverter board, then run the display test program again. If the problem still occurs, go
on next step.
Replace the LCD module with a new one then run the display test again. If the probelm still
happens, continue next step.
Replace LCD/FL cable with a new one then execute the display diagnostic again. If the problem
Chapter 4
74
still occurs, continue next step.
Replace the CPU with another of the same specifications. If the problems still occurs, go to next
step.
The main board may be damaged. Replace main board.
3.
If the external monitor has the same problem as the internal monitor, the main board may be damaged.
Please insert the diagnostic disk and run the display test program and go through the sub-steps under
step 2.
Sound Check
To determine if the computer’s built-in speakers are functioning properly, perform the following steps. Before
you start the steps below, adjust the speaker volume to an appropriate level.
75
1.
Try different audio sources. For example, employ audio CD and ditital music file to determine whether the
fault is in the speaker system or not. If not all sources have sound problem, the problem is in the source
devices. If all have the same problem, continue next step.
2.
Connect a set of earphone or external speakers. If these devices work fine, go to next step. If not, then the
main board may be defective or damaged. Replace the main board.
3.
Follow the disassembling steps in Chapter 3. Esure the speaker cable is firmly connected to the main
board. If the speaker is still a malfunction, go on next step.
4.
If the speakers do not sound properly, the speakers may be defective or damaged. Replace the speakers.
If the problem still occurs, then replace the main board.
Chapter 4
Insyde MobilePro BIOS POST Beep Code and POST Messages
The POST error message index lists the error message and their possible causes. The most likely cause is
listed first.
NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU
replacement does not solve the problem, put the original part back in the computer. Do not replace a
non-defective FRU.
This index can also help you determine the next possible FRU to be replaced when servicing a computer.
If the symptom is not listed, see “Undetermined Problems” on page 73.
The following lists the error messages that the BIOS displays on the screen and the error symptoms classified
by function.
NOTE: Most of the error messages occur during POST. Some of them display information about a hardware
device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the
way it has been configured.
NOTE: If the system fails after you make changes in the BIOS Setup Utility menus, reset the computer, enter
Setup and install Setup defaults or correct the error.
Beep Code
Message
Description
short, short, short; short,
short, long
“FAULTY DMA PAGE
REGISTERS”
DMA page registers do not function
properly.
short, short, short; short,
long, short
“FAULTY REFRESH CIRCUIT”
RAM refresh circuit does not function
properly.
short, short, short; short,
long, long
“ROM CHECKSUM INCORRECT” BIOS ROM checksum failed.
short, short, short; long,
short, short
“CMOS RAM TEST FAILED”
CMOS RAM test failed.
short, short, short; long,
short, long
“DMA CONTROLLER FAULTY”
DMA controller does not work properly.
short, short, short; long,
long short
“INTERRUPT CONTROLLER
FAILED”
The interrupt controller does not work
properly.
short, short, short; long,
long, long
N/A
Keyboard controller failed to respond with
the self-test command.
short, short, long; short,
short, short
N/A
No video device found.
short, short, long; short,
short, long
N/A
No RAM installed.
N/A
“KEYBOARD CONTROLLER
FAILURE”
Keyboard controller failed during system
inquiry about connected devices.
N/A
“KEYBOARD FAILURE”
The keyboard fails to respond or no keyboard is connected.
N/A
“CMOS FAILURE - RUN SCU”
CMOS data error, probably due to battery
power loss.
N/A
“CMOS CHECKSUM INVALID RUN SCU”
CMOS checksum error.
N/A
“RAM ERROR AT LOCATION
xxxxxx:
WROTE: xxxx
READ: xxxx”
The RAM failed during memory test at the
indicated location.
Chapter 4
76
Beep Code
77
Message
Description
N/A
“PARITY ERROR AT UNKNOWN
LOCATION”
Parity error during memory test at unknown
location.
N/A
“PARITY ERROR AT LOCATION
XXXXXX”
Parity error during memory test at the
indicated location.
N/A
“NO INTERRUPTS FROM TIMER
0”
Timer 0 of the clock timer controller does
not generate system interrupts correctly.
N/A
“UNEXPECTED AMOUNT OF
MEMORY - RUN SCU”
The system memory size does not match
with the CMOS record.
N/A
“CLOCK NOT TICKING
CORRECTLY”
The system clock does not working
correctly.
N/A
“TIME/DATA CORRUPT - RUN
SCU”
The time/date information in CMOS is
invalid.
N/A
“MACHINE IS LOCKED - TURN
KEY”
The keyboard operation is locked.
N/A
“BOOT SECTOR 0 HAS
CHANGED”
The boot sector of the hard disk has been
changed, probably because of a virus
attack.
N/A
Suspend-to-Disk partition
MISSING!”
No Suspend-to-Disk partition found.
N/A
“Hard Disk ERROR!”
Access to the Suspend-to-Disk partition
failed.
N/A
“Suspend-to-Disk partition
signature NOT FOUND!”
No Suspend-to-Disk partition signature
found.
N/A
“Suspend-to-Disk partition size
TOO SMALL!”
The capacity of the Suspend-to-Disk
partition is not enough.
N/A
“MEMORY SIZE HAS CHANGED
-- REBOOTING”
The memory size has changed after
previous Suspend-to-Disk operation.
Chapter 4
Index of Symptom-to-FRU Error Message
LCD-Related Symptoms
Symptom / Error
Action in Sequence
LCD backlight doesn't work
LCD is too dark
LCD brightness cannot be adjusted
LCD contrast cannot be adjusted
Enter BIOS Utility to execute “Load Setup Defaults” on Exit
screen, then reboot system.
Reconnect the LCD connectors.
Keyboard (if contrast and brightness function key doesn't
work).
LCD cable
LCD inverter
LCD
Main board
Unreadable LCD screen
Missing pels in characters
Abnormal screen
Wrong color displayed
Reconnect the LCD connector
LCD cable
LCD inverter
LCD
Main board
LCD has extra horizontal or vertical lines
displayed.
LCD inverter
LCD cable
LCD
Main board
Indicator-Related Symptoms
Symptom / Error
Indicator incorrectly remains off or on, but
system runs correctly
Action in Sequence
Reconnect the inverter board
Inverter board
Main board
Power-Related Symptoms
Symptom / Error
Action in Sequence
Power shuts down during operation
Power source (battery pack and power adapter). See “Power
System Check” .
Battery pack
Power adapter
Hard drive & battery connection board
Main board
The system doesn’t power-on.
Power source (battery pack and power adapter). See “Power
System Check” .
Battery pack
Power adapter
Hard drive & battery connection board
Main board
The system doesn’t power-off.
Power source (battery pack and power adapter). See “Power
System Check” .
Hold and press the power switch for more than 4 seconds.
Main board
Battery can’t be charged
See “Check the Power Adapter”.
Battery pack
Main board
Chapter 4
78
PCMCIA-Related Symptoms
Symptom / Error
Action in Sequence
System cannot detect the PC Card
(PCMCIA)
PCMCIA slot assembly
Main board
PCMCIA slot pin is damaged.
PCMCIA slot assembly
Memory-Related Symptoms
Symptom / Error
Memory count (size) appears different from
actual size.
Action in Sequence
DIMM
Main board
Speaker-Related Symptoms
Symptom / Error
Action in Sequence
In Windows, multimedia programs, no
sound comes from the computer.
See “Sound Check” on page 66
Audio driver
Speaker
Main board
Internal speakers make noise or emit no
sound.
See “Sound Check” on page 66
Speaker
Main board
Power Management-Related Symptoms
Symptom / Error
79
Action in Sequence
The system will not enter hibernation
Keyboard (if control is from the keyboard)
Hard disk drive
Main board
The system doesn't enter hibernation mode
and four short beeps every minute.
Press Fn+F4 and see if the computer enters hibernation
mode.
Touchpad
Keyboard
Hard disk connection board
Hard disk drive
Main board
The system doesn’t enter standby mode
after closing the LCD
LCD cover switch
Main board
The system doesn't resume from
hibernation mode.
Hard disk connection board
Hard disk drive
Main board
The system doesn't resume from standby
mode after opening the LCD.
LCD cover switch
Main board
Battery fuel gauge in Windows doesn’t go
higher than 90%.
Remove battery pack and let it cool for 2 hours.
Refresh battery (continue use battery until power off, then
charge battery).
Battery pack
Main board
Chapter 4
Power Management-Related Symptoms
Symptom / Error
System hangs intermittently.
Action in Sequence
Reconnect hard disk drives.
Hard disk drive connector
Main board
Peripheral-Related Symptoms
Symptom / Error
Action in Sequence
System configuration does not match the
installed devices.
Enter BIOS Setup Utility to execute “Load Setup defaults”,
then reboot system.
Reconnect hard disk/CD-ROM/diskette drives.
External display does not work correctly.
See if there is an error beep. If there is an erro beep, then
change main board.
Power off. Then check if RAM CPU BIOS are wellconnected.
Press Fn+F5 three times slowly
LCD FPC
LCD inverter
LCD
USB does not work correctly
USB device cable is firmly connected into the USB ports.
Test one USB port each time.
USB socket is firmly secured to the main board.
Main board
Print problems.
Ensure the “Parallel Port” in the “System Devices” of BIOS
Setup Utility is set to Enabled.
Onboard Devices Configuration
Run parallel port test
Printer driver
Printer cable
Printer
Main board
Keyboard/Touchpad-Related Symptoms
Symptom / Error
Action in Sequence
Keyboard (one or more keys) does not
work.
Reconnect the keyboard cable.
Keyboard
Main board
Touchpad does not work.
Reconnect touch pad cable. Modem port is secured to the
main board
Touch pad FPC
Audio/Touch pad board
Main board
Chapter 4
80
Modem-Related Symptoms
Symptom / Error
Internal modem does not work correctly.
81
Action in Sequence
Ensure the telephone cable is firmly plugged into the
telephone wall socket and the modem port of the computer.
Modem phone port is secured to the main board.
modem combo board
Main board
Chapter 4
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
1.
Run the diagnostic test for several times to isolate the problem.
2.
If no error is detected, do not replace any FRU.
3.
If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
Chapter 4
82
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,
whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
83
1.
Power-off the computer.
2.
Visually check them for damage. If any problems are found, replace the FRU.
3.
Remove or disconnect all of the following devices:
T
Non-Acer devices
T
Printer, mouse, and other external devices
T
Battery pack
T
Hard disk drive
T
DIMM
T
CD-ROM/Diskette drive Module
T
PC Cards
4.
Power-on the computer.
5.
Determine if the problem has changed.
6.
If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7.
If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
T
Main board
T
LCD assembly
Chapter 4
How to Build NAPP Master Hard Disc Drive
CD to Disk Recovery
1.
Prepare NAPP CD, Recovery CD and System CD.
2.
Insert the NAPP CD into the optical drive. Then boot up the system.
3.
The system will ask you if you want to build NAPP Master HDD. Please press any key to continue.
4.
NAPP CD will start to preload the system, please click [Y].
Chapter 4
84
5.
Select CD to Disk Revocery.
6.
Put the Recovery CD to the optical drive. This step is to create image files to the system, you do not have
to put the Recovery CD to the optical drive in order. Place one Recovery CD to the drive at one time till
you finish all Recovery CDs.
After you place the Recovery CD to the optical drive, you will see the display below.
85
Chapter 4
7.
Then insert the System CD to the optical drive.
Chapter 4
86
8.
You will see the screen displaying “PASS” when the system has buit NAPP Master hard disc drive.
Disk to Disk Recovery
87
1.
Prepare NAPP CD, Recovery CD and System CD.
2.
Put NAPP CD into the optical drive. Then boot up the system.
3.
The system will ask you if you want to build NAPP Master HDD. Please press any key to continue.
Chapter 4
4.
NAPP CD will start to preload the system, please click [Y].
5. Select Disk to Disk Recovery. Then choose Single Language or Multi-Languages Recovery.
NOTE: For Multi-Languages Recovery, not more than five languages could be loaded to the system.
Chapter 4
88
6.
Put the Recovery CD to the optical drive. This step is to create image files to the system, you do not have
to put the Recovery CD to the optical drive in order. Place one Recovery CD to the drive at one time till
you finish all Recovery CDs.
After you place the Recovery CD to the optical drive, you will see the display below.
89
Chapter 4
7.
Then insert the System CD to the optical drive.
8.
You will see the screen displaying “PASS” when the system has buit NAPP Master hard disc drive.
Chapter 4
90
Chapter 5
Jumper and Connector Locations
Top View
Item
Description
JP1
RJ11/RJ45 Connector
JP2
CRT Connector
JP3
Printer Connector
JP4
TV-Out Connector
JP5/6/7
USB Connector
JP8
IEEE 1394 Connector
JP9
Power Board Connector
JP10
MDC Cable Connector
JP11
LCD Connector
JP12
Cardbus Connector
JP13
FAN Connector
JP14
MDC Connector
JP15
Right Speaker Connector
JP16
Left Speaker Connnector
JP17
Subwoofer Connector
JP18
LCM Connector
JP19
SD Board Connector
JP20
Int. K/B Connector
JP21
Bluetooth Connector
JP22
DDR SODIMM Socket
JP23
ODD Speaker
Chapter 5
91
Item
92
Description
JP24
T/P Board Connector
JP25
HDD Connector
PCN2
AC Jack
PCN3
Battery Connector
Chapter 5
Bottom View
Item
Description
JP27
Mini-PCI Connector
JP29
DDR SODIMM Socket
U40
BIOS ROM
U45
Cardbus Controller
Chapter 5
93
Power Board
Top View
Rear View
Item
94
Description
SW5
Power Button
SW2
User Button 1
SW3
User Button 1
SW4
Internet Bottom
SW1
E-Mail Bottom
JP1
To M/B Connector
D1
Scroll Lock LED
D2
Num Lock LED
D3
Caps Lock LED
D4
E-Mail LED
Chapter 5
T/P Board
Top View
Rear View
Item
Description
Item
Description
SW1
Scroll-Up Buttom
SW7
Lid Switch
SW2
Scroll-left Buttom
JP1
To Touch Pad Cable
SW3
Scroll-Right Buttom
JP2
To Buttom Board Cable
Chapter 5
95
Item
96
Description
Item
Description
SW4
Scroll-Down Buttom
JP3
To LED Board Cable
SW5
Left Buttom
JP4
To M/B Cable
SW6
Right Buttom
JP5
To Media Board Cable
Chapter 5
SD Board
Top View
Rear View
Item
Description
JP1
Card Reader Socket
JP2
MIC-In/Line-In Jack
JP3
SPDIF/Headphone-Out Jack
JP4
To M/B wire connector
Chapter 5
97
Media Board
Top View
Rear View
Item
98
Description
SW1
Stop Bottom
SW2
Backward Bottom
SW3
Media Control Bottom
SW4
Forward Bottom
JP1
To T/P Board Connector
Chapter 5
LED Board
Top View
Rear View
Item
Description
SW1
Arcade Bottom
JP1
To T/P Board Connector
D1/D2
Power Status LED
D3
Activity LED
D4/D5
Battery Status LED
MIC1
Internal Microphone
Chapter 5
99
Bottom Board
Top View
Rear View
Item
SW1
100
Description
Bluetooth On/Off Bottom
SW2
Wireless On/Off Bottom
JP1
To T/P Board Connector
D1
Bluetooth Status LED
D2
Wireless Status LED
Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of Aspire 2010/2020.
Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).
Please also note that there are some common parts for Aspire 2000, yet the LCD modules are different
in two model.
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information
available on your regional web or channel. For whatever reasons a part number change is made, it
will not be noted on the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS,
your Acer office may have a DIFFERENT part number code from those given in the FRU list of this
printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to
order FRU parts for repair and service of customer machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or
regulations on how to dispose it properly, or follow the rules set by your regional Acer office on how to
return it.
Chapter 6
101
Exploded Diagram
102
Chapter 6
Aspire 2010 Parts List
PHOTO
PARTNAME
ACER P/N
ADAPTER
ADAPTER W/LED-DELTA 65W ADP-65B
AP.T2101.001
ADAPTER W/O LED-LITEON 65W PA-1650-02CR
AP.T3503.001
BATTERY LI-ION&CELLS-PANASONIC
TBD
BATTERY
GC86503PAJ0
BATTERY LI-ION&CELLS-SAMSUNGGC86508SMG0
TBD
MODEM BOARD AMBIT T60M283
54.A14V5.001
MINI PCI WIRELESS BOARD (802.11b)INTEL
54.A14V5.002
MINI PCI WIRELESS BOARD (802.11 b+g)
54.A24V5.001
LAUNCH BOARD
55.A24V5.001
WIRELESS & B/T SWITCH BOARD
55.A14V5.003
BOARD
Chapter 6
103
PHOTO
PARTNAME
ACER P/N
LCM BOARD
55.A25V5.001
LED BOARD
55.A25V5.002
MEDIA BOARD
55.A25V5.003
T/P BOARD W/4*FFC
55.A25V5.004
CARD READER WIRE SET
50.A24V5.001
MODEM CABLE
50.A24V5.002
LCM TO MB FFC
50.A25V5.001
CABLES
TOUCHPAD FFC CABLE
50.A24V5.003
POWER CORD US
27.A14V5.001
POWER CORD EC
27.A14V5.002
POWER CORD AUS
27.A14V5.003
POWER CORD UK
27.A14V5.004
POWER CORD SWISS
27.A14V5.005
POWER CORD CHINA
27.A14V5.006
POWER CORD ITALIAN
27.A14V5.007
POWER CORD DENMARK
27.A14V5.008
CASE/COVER/BRACKET ASSEMBLY
104
Chapter 6
PHOTO
Chapter 6
PARTNAME
ACER P/N
MIDDLE COVER W/NAME PLATE
42.A25V5.001
LOWER CASE ASSY
60.A25V5.001
DIMM COVER
42.A14V5.002
UPPER CASE ASSY W/O SPEAKER FAN HINGE
SIDDLE
60.A14V5.002
MINI PCI COVER
42.A14V5.003
TOUCHPAD BRACKET
33.A24V5.001
HINGE SADDLE -R
33.A14V5.008
HINGE SADDLE-L
33.A14V5.009
105
PHOTO
PARTNAME
ACER P/N
VGA PLATE W/THURMAL PAD
33.A24V5.002
ANTENNA ASSY
50.A14V5.006
DVD/CDRW COMBO MODULE PANASONIC
(SLOT IN) (CW-8123)
6M.A25V5.001
DVD/CDRW COMBO DRIVE PANASONIC (SLOT
IN) (CW-8123)
TBD
COMMUNICATION MODULE
COMBO DRIVE
CASE/COVER/BRACKET ASSEMBLY
DVD/CDRW COMBO BEZEL FOR PANASONIC
(SLOT IN)
42.A25V5.002
OPTICAL DEVICE BRACKET
33.A14V5.004
DVD SUPER MULTI MODULE MKE (SLOT IN)(UJ825)
6M.A25V5.002
DVD SUPER MULTI DRIVE MKE (SLOT IN)(UJ825)
TBD
DVD RW DRIVE
CASE/COVER/BRACKET ASSEMBLY
DVD SUPER MULTI BEZEL FOR MKE (SLOT
IN)(UJ-825)
42.A25V5.003
OPTICAL DEVICE BRACKET
33.A14V5.004
HDD CARRIER
42.A14V5.007
HDD CONNECTOR
20.A14V5.001
KEYBOARD ARABIC
KB.A1402.011
KEYBOARD BELGIUM
KB.A1402.013
KEYBOARD CHINESE
KB.A1402.005
KEYBOARD CZECH
KB.A1402.015
KEYBOARD
106
KEYBOARD DANISH
KB.A1402.018
KEYBOARD FRENCH
KB.A1402.006
KEYBOARD GERMAN
KB.A1402.003
KEYBOARD ITALIAN
KB.A1402.004
KEYBOARD NORWEGIAN
KB.A1402.017
KEYBOARD PORTUGUESE
KB.A1402.010
KEYBOARD SPANISH
KB.A1402.009
KEYBOARD SWEDEN
KB.A1402.014
KEYBOARD SWISS/G
KB.A1402.008
KEYBOARD THAI
KB.A1402.012
KEYBOARD UK
KB.A1402.002
Chapter 6
PHOTO
PARTNAME
ACER P/N
KEYBOARD US INTERNATIONAL
KB.A1402.001
KEYBOARD HUNGAIAN
KB.A1402.016
KEYBOARD CANADIAN FRENCH
KB.A1402.007
KEYBOARD RUSSIAN
KB.A1402.019
ASSY LCD MODULE 15.4 IN. WXGA SAMSUNG
(LTN154X1-L02)
6M.A25V5.011
LCD 15.4 IN. WXGA SAMSUNG (LTN154X1-L02)
LK.15406.001
LCD INVERTER
19.A14V5.001
LCD SAMSUNG MODULE
BOARD
CASE/COVER/BRACKET ASSEMBLY
LCD PANEL WITH LOGO W/ANTENNA-METAL
60.A25V5.002
LCD BEZEL
42.A14V5.008
LCD BRACKET L
33.A14V5.006
LCD BRACKET R
33.A14V5.007
LCD COAXIAL CABLE 15.4 IN WXGA SAMSUNG
50.A24V5.004
LCD RUBBER
47.A14V5.001
LCD SCREW PAD
47.A14V5.002
ASSY LCD MODULE 15.4 IN. WXGA LG
(LP154W01-A3)
6M.A25V5.012
LCD 15.4 IN. WXGA LG (LP154W01-A3)
LK.15408.001
LCD INVERTER
19.A14V5.001
CABLE
MISCELLANEOUS
LCD LG MODULE
BOARD
CASE/COVER/BRACKET ASSEMBLY
LCD PANEL WITH LOGO W/ANTENNA-METAL
60.A25V5.002
LCD BEZEL
42.A14V5.008
LCD BRACKET L
33.A14V5.006
LCD BRACKET R
33.A14V5.007
LCD COAXIAL CABLE 15.4 IN. WXGA LG
50.A24V5.005
LCD RUBBER
47.A14V5.001
LCD SCREW PAD
47.A14V5.002
ASSY LCD MODULE 15.4 IN. WXGA AU
(B154EW01)
6M.A25V5.013
LCD 15.4 IN. WXGA AU (B154EW01)
LK.15401.001
LCD INVERTER
19.A14V5.001
CABLE
MISCELLANEOUS
LCD AU MODULE
BOARD
CASE/COVER/BRACKET ASSEMBLY
Chapter 6
107
PHOTO
PARTNAME
ACER P/N
LCD PANEL WITH LOGO W/ANTENNA-METAL
60.A25V5.002
LCD BEZEL
42.A14V5.008
LCD BRACKET-L
33.A14V5.006
LCD BRACKET-R
33.A14V5.007
LCD COAXIAL CABLE 15.4IN. WXGA AU
50.A24V5.006
LCD RUBBER
47.A14V5.001
LCD SCREW PAD
47.A14V5.002
MAINBOARD 128MB W/PCMCIA SLOT W/O CPU
MEMORY
LB.A2502.001
CABLE
MISCELLANEOUS
MAINBOARD
CASE/COVER/BRACKET ASSEMBLY
PCMCIA SLOT
22.A14V5.001
PCMCIA DUMMY CARD
42.A14V5.009
FAN
23.A14V5.001
THERMAL MODULE
60.A14V5.004
TOUCHPAD
56.A14V5.001
4 IN 1 CARD READER BOARD
55.A25V5.005
SPEAKER SET (R&L) - FORTUNE/VECO
6K.A14V5.001
SUB-WOOFER
23.A25V5.001
RUBBER FOOT
47.A14V5.003
SCREW, JIM M2.0X4
86.A14V5.001
SCREW, JIM M2.5X4
86.A14V5.002
SCREW, JIM M2.5X5
86.A14V5.003
SCREW, JIM M2.5X10
86.A14V5.004
SCREW, JIM M2.5X14
86.A14V5.005
SCREW, JIM M3.0X3
86.A14V5.006
SCREW, JIM M2.0X8 (Ni)
86.A14V5.007
SCREW, JIM M2.0X6 (Ni)
86.A14V5.008
SCREW, JACK SCREW
86.A14V5.009
SCREW, SPEACIAL SCREW
86.A14V5.011
FAN
HEATSINK
POINTING DEVICE
READER
SPEAKER
MISCELLANEOUS
SCREW LIST
108
Chapter 6
Aspire 2020 Parts List
PHOTO
PARTNAME
ACER P/N
ADAPTER
ADAPTER W/LED-DELTA 65W ADP-65B
AP.T2101.001
ADAPTER W/O LED-LITEON 65W PA-1650-02CR
AP.T3503.001
BATTERY LI-ION&CELLS-PANASONIC
BT.A2401.002
BATTERY
GC86503PAJ0
BATTERY LI-ION&CELLS-SAMSUNGGC86508SMG0
BT.A2401.001
BATTERY LI-ION&CELLS 2150mAH-PANASONIC
BT.A2401.003
MODEM BOARD AMBIT T60M283
54.A14V5.001
MINI PCI WIRELESS BOARD (802.11b)INTEL
54.A14V5.002
MINI PCI WIRELESS BOARD (802.11 b+g)
54.A24V5.001
LAUNCH BOARD
55.A24V5.001
WIRELESS & B/T SWITCH BOARD
55.A14V5.003
LED BOARD
55.A24V5.002
T/P BOARD W/3*FFC
55.A24V5.003
AUDIO CARD
55.A24V5.004
CARD READER WIRE SET
50.A24V5.001
MODEM CABLE
50.A24V5.002
BOARD
CABLES
TOUCHPAD FFC CABLE
50.A24V5.003
POWER CORD US
27.A14V5.001
POWER CORD EC
27.A14V5.002
POWER CORD AUS
27.A14V5.003
POWER CORD UK
27.A14V5.004
POWER CORD SWISS
27.A14V5.005
POWER CORD CHINA
27.A14V5.006
POWER CORD ITALIAN
27.A14V5.007
POWER CORD DENMARK
27.A14V5.008
CASE/COVER/BRACKET ASSEMBLY
Chapter 6
MIDDLE COVER W/NAME PLATE
42.A24V5.001
LOWER CASE ASSY FOR 4 IN 1 READER
60.A24V5.001
LOWER CASE ASSY NON 4 IN 1 READER
60.A24V5.002
DIMM COVER
42.A24V5.002
UPPER CASE ASSY W/O SPEAKER FAN HINGE
SIDDLE FOR 4 IN 1 READER
60.A24V5.003
UPPER CASE ASSY W/SPEAKER FAN HINGE
SIDDLE NON 4 IN 1 READER
60.A24V5.004
MINI PCI COVER
42.A24V5.003
TOUCHPAD BRACKET
33.A24V5.001
HINGE SADDLE -R
33.A14V5.008
109
PHOTO
PARTNAME
ACER P/N
HINGE SADDLE -L
33.A14V5.009
VGA PLATE W/THURMAL PAD
33.A24V5.002
VGA PLATE W/O THURMAL PAD
33.A24V5.003
SUB-WOOFER CASE
60.A24V5.006
ANTENNA ASSY
50.A14V5.006
DVD/CDRW COMBO MODULE QSI (TRAY
IN)(242C)
6M.A24V5.001
DVD/CDRW COMBO DRIVE HLDS
(TRAY)(GCC4241N)
TBD
COMMUNICATION MODULE
COMBO DRIVE
CASE/COVER/BRACKET ASSEMBLY
DVD/CDRW COMBO BEZEL FOR HLDS (TRAY)
42.A24V5.004
OPTICAL DEVICE BRACKET
33.A14V5.004
DVD/CDRW COMBO MODULE QSI (TRAY
IN)(242C)
6M.A24V5.002
DVD/CDRW COMBO DRIVE QSI(TRAY IN)(242C)
TBD
COMBO DRIVE
CASE/COVER/BRACKET ASSEMBLY
DVD/CDRW COMBO BEZEL FOR QSI (TRAY
IN)(242C)
42.A24V5.005
OPTICAL DEVICE BRACKET
33.A14V5.004
DVD/CDRW COMBO MODULE KME (TRAY
IN)(UJDA750)
6M.A24V5.003
DVD/CDRW COMBO DRIVE KME (TRAY IN)(UJDA
750)
TBD
COMBO DRIVE
CASE/COVER/BRACKET ASSEMBLY
DVD/CDRW COMBO BEZEL FRO KME (TRAY
IN)(UJDA750)
42.A24V5.006
OPTICAL DEVICE BRACKET
33.A14V5.004
DVD SUPER MULTI MODULE KME (TRAY
IN)(UJ820B)
6M.A24V5.005
DVD SUPER MULTI DRIVE KME (TRAY
IN)(UJ820B)
TBD
DVD RW DRIVE
CASE/COVER/BRACKET ASSEMBLY
DVD SUPER MULTI BEZEL FOR KME (TRAY
IN)(UJ820B)
42.A24V5.008
OPTICAL DEVICE BRACKET
33.A14V5.004
HDD CARRIER
42.A14V5.007
HDD CONNECTOR
20.A14V5.001
KEYBOARD ARABIC
KB.A2405.011
KEYBOARD BELGIUM
KB.A2405.013
KEYBOARD CHINESE
KB.A2405.005
KEYBOARD
110
Chapter 6
PHOTO
PARTNAME
ACER P/N
KEYBOARD CZECH
KB.A2405.015
KEYBOARD DANISH
KB.A2405.018
KEYBOARD FRENCH
KB.A2405.006
KEYBOARD GERMAN
KB.A2405.003
KEYBOARD ITALIAN
KB.A2405.004
KEYBOARD NORWEGIAN
KB.A2405.017
KEYBOARD PORTUGUESE
KB.A2405.010
KEYBOARD SPANISH
KB.A2405.009
KEYBOARD SWEDEN
KB.A2405.014
KEYBOARD SWISS/G
KB.A2405.008
KEYBOARD THAI
KB.A2405.012
KEYBOARD UK
KB.A2405.002
KEYBOARD US INTERNATIONAL
KB.A2405.001
KEYBOARD HUNGAIAN
KB.A2405.016
KEYBOARD CANADIAN FRENCH
KB.A2405.007
KEYBOARD RUSSIAN
KB.A2405.019
ASSY LCD MODULE 15.4 IN. WXGA SAMSUNG
(LTN154X1-L02)
6M.A24V5.011
LCD 15.4 IN. WXGA SAMSUNG (LTN154X1-L02)
LK.15406.001
ASSY LCD MODULE 15.4 IN. WXGA LG
(LP154W01-A3)
6M.A24V5.012
LCD 15.4 IN. WXGA LG (LP154W01-A3)
LK.15408.001
LCD
ASSY LCD MODULE 15.4 IN. WXGA (B154EW01)
6M.A24V5.013
LCD 15.4 IN WXGA AU (B154EW01)
LK.15401.001
LCD INVERTER
19.A14V5.001
BOARD
CASE/COVER/BRACKET ASSMEBLY
LCD PANEL WITH LOGO W/ANTENNA-PLASTIC
60.A24V5.005
LCD BEZEL
42.A14V5.008
LCD BRACKET L
33.A14V5.006
LCD BRACKET R
33.A14V5.007
PCMCIA SLOT
22.A14V5.001
PCMCIA DUMMY CARD
42.A14V5.009
LCD COAXIAL CABLE 15.4 IN. WXGA SAMSUNG
50.A24V5.004
LCD COAXIAL CABLE 15.4 IN. WXGA LG
50.A24V5.005
LCD COAXIAL CABLE 15.4 IN. WXGA AU
50.A24V5.006
LCD RUBBER
47.A14V5.001
LCD SCREW PAD
47.A14V5.002
RUBBER FOOT
47.A14V5.003
CABLE
MISCELLANEOUS
Chapter 6
111
PHOTO
PARTNAME
ACER P/N
MAINBOARD DISCRETE 64MB W/PCMCIA SLOT
W/O CPU MEMORY
LB.A2402.001
MAINBOARD UMA W/PCMCIA SLOT W/O CPU
MEMORY
LB.A2402.002
FAN
23.A14V5.001
THERMAL MODULE
60.A14V5.004
TOUCHPAD
56.A14V5.001
4 IN 1 CARD READER BOARD
55.A14V5.006
SPEAKER SET (R&L) FORTUNE/ECO
6K.A14V5.001
SCREW, JIM M2.0X4
86.A14V5.001
SCREW, JIM M2.5X4
86.A14V5.002
SCREW, JIM M2.5X5
86.A14V5.003
SCREW, JIM M2.5X10
86.A14V5.004
SCREW, JIM M2.5X14
86.A14V5.005
SCREW, JIM M3.0X3
86.A14V5.006
SCREW, JIM M2.0X8 (Ni)
86.A14V5.007
SCREW, JIM M2.0X6 (Ni)
86.A14V5.008
SCREW, JACK SCREW
86.A14V5.009
SCREW, SPEACIAL SCREW
86.A14V5.011
FAN
HEATSINK
POINTING DEVICE
READER
SPEAKER
SCREWS
112
Chapter 6
Appendix A
Model Definition and Configuration
Aspire 2010/2020 series
Model
Number
Card
Reader
CPU
LCD
Memory
HDD
Optical
Mini PCI
2012WLCi
PM
1.5GH
z/1M
15.4"
WXGA
DDR333
1x256M
B
40GB
24x
Combo
802.11b/gAS2010
N/A
Li-IonAS201
0
2012WLMi
PM
1.5GH
z/1M
15.4"
WXGA
DDR333
2x256M
B
40/
60GB
4x DVDDual
802.11b/gAS2010
4 in 1AS2010
Li-IonAS201
0
2025WLMi
PM
1.8GH
z/2M
15.4"
WXGA
DDR333
2x256M
B
60/
80GB
Slot 4x
DVDSMulti
802.11b/gAS2020
4 in 1AS2020
Li-IonAS202
0
Appendix A
Battery
113
Appendix B
Test Compatible Components
This computer’s compatibility is tested and verified by Acer’s internal testing department. All of its system
functions are tested under Windows XP Home and Windows XP Professional environment.
Refer to the following lists for components, adapter cards, and peripherals which have passed these tests.
Regarding configuration, combination and test procedures, please refer to the Aspire 2010/2020 Compatibility
Test. Report released by the Acer Mobile System Testing Department.
Appendix B
114
Microsoft Windows XP Home Environment Test
Description
CPU
HDD
Model Number
Intel Pentium-M (Banias) 1.4GHz 1M/400MHz FSB
KC.BS001.14G
Intel Pentium-M (Banias) 1.5GHz 1M/400MHz FSB
KC.BS001.15G
Intel Pentium-M (Banias) 1.6GHz 1M/400MHz FSB
KC.BS001.16G
Intel Pentium-M (Banias) 1.7GHz 1M/400MHz FSB
KC.BS001.17G
Intel Pentium-M (Dothan) 1.6GHz 2M/400MHs FSB
TBD
Intel Pentium-M (Dothan) 1.7GHz 2M/400MHz FSB
KC.ND001.17G
Intel Pentium-M (Dothan) 1.8GHz 2M/400MHz FSB
KC.ND001.18G
HDD 2.5” HGST Moraga IC25N030ATMR04-0
08K0910 30G 4200PRM
08K0910
KH.03007.005
HDD 2.5” Toshiba Pluto MK4025GAS 40GB
4200PRM
MK4025GAS
KH.04004.002
HDD 2.5” HGST Moraga IC25N040ATMR04-0
08K0633 40G 4200PRM (F/W:AD4A)
08K0633
KH.04007.009
HDD 2.5” Seagate N1 ST94019A 2MB 40GB
4200PRM (F/W:3.05)
ST94019A
KH.04001.010
HDD 2.5” HGST Moraga IC25N060ATMR04-0
08K0634 60G 4200RPM(F/W:AD4A)
08K0634
KH.06007.006
HDD 2.5” Toshiba Pluto MK6025GAS 60GB
4200RPM
08K0638
KH.06007.002
HDD 2.5” HGST Moraga IC25N080ATCS04-0
08K0635 80G 4200RPM
08K0635
KH.08007.007
HDD 2.5" HGST Moraga HTS548080M9AT00
08K0639 80G 5400rpm
08K0639
KH.08007.003
Samsung 15.4" WXGA (1280 x 800) TFT Panel
LTN154X1-L02
LK.15406.003
LG 15.4" WXGA (1280 x 800) TFT Panel.
LP154W01-A3
LK.15408.001
AU 15.4" WXGA (1280 x 800) TFT Panel
B154EW01
LK.15405.001
Sanyo 15.4" WXGA (1280 x 800) TFT Panel
TM154WX22L31
LK.1540J.001
QDI 15.4" WXGA (1280 x 800) TFT Panel
QD15TL02-01
LK.15409.001
LG 15.4" WSXGA+ (1600 x 1050) TFT Panel
LP154W02-A1
LK.15408.002
LG 15.4" WSXGA+ (1600 x 1050) TFT Panel
LP154W02-B1
LK.15408.003
Intel 855GME
Intel ICH4-M
115
KH.06004.003
HDD 2.5” HGST Moraga HTS548060M9AT00
08K0638 60G 5400RPM
LCD Panel
Chipset
Acer P/N
KI.80101.005
Appendix B
Description
Model Number
QSI 12.7mm Tray Type DVD/CDRW combo 24/24/
24,8X
SBW-242C (for
Drongo3/4)
KO.02407.013
Pnansonic 12.7mm tray Type DVD/CDRW combo
24/24/24,8X
UJDA750-II (for
Drongo3/4)
KO.02406.004
HLDS 12.7mm Tray Type DVD/CDRW combo 24/24/ GCC-4241N
24,8X
(for Drongo3/4)
KO.02405.001
QSI 12.7mm Tray Type DVD-Dual
SDW-042 (for
Drongo3/4)
KU.00403.002
HLDS 12.7mm Tray Type DVD-Dual
GSA-4040N (for KU.0040D.004
Drongo3/4)
Pnansonic 12.7mm Tray Type Super Multi
UJ820B (for
Drongo3/4)
KU.00407.003
Pnansonic 12.7mm Slot-in DVD/CDRW combo
CW-8123 (for
Drongo2)
KO.02406.005
Pnansonic 12.7mm Slot-in Super Multi
UJ-825 (for
Drongo2)
KU.00407.004
Optical Drive
Memory
Wireless LAN
Acer P/N
Infineon SO-DIMM DDR333 256MB
HYS64D32020GDL-6-B 16x16x8 (0.14u)
KN.25602.009
Infineon SO-DIMM DDR333 512MB
HYS64D64020GBDL-6-C 64Mx64 (0.11u/black)
KN.51202.013
Nanya SO-DIMM DDR333 256MB
NT256D64SH8BAGM-6KE (.14u)
KN.25603.014
Nanya SO-DIMM DDR333 512MB
NT512D64S8HBAFM-6K (.14u)
KN.51203.005
Micron SO-DIMM DDR333 256MB
MT8VDDT3264HDG-335C3 (.13u)
KN.25604.009
Micron SO-DIMM DDR333 256MB MT8VDDT3264H
G-335G3 (0.11u)
KN.25604.014
Micron SO-DIMM DDR 333 512MB
MT16VDDF6464H G-335G2 (0.11u)
KN.51204.012
Intel Wireless LAN, MiniPCI Type 3B Intel 802.11b
KI.CAX01.007
Intel Wireless LAN, MiniPCI Type 3B Intel 802.11b/g
Battery
Mainboard
Adapter
Appendix B
AS2010 BATCL32CL 8Cell (Samsung)
BT.A2401.001
AS2010 BATCL32CL 8Cell (Panasonic)
BT.A2401.002
AS2010 BATCL32L4 4Cell (Panasonic)
BT.A2401.003
AS2020 BAT CL32CL 8CELL (Samsung)
BT.A2501.001
AS2020 BAT CL32CL 8CELL (Panasonic)
BT.A2501.002
AS2010 Discrete Mainboard
LB.A2402.001
AS2020 Mainboard
LB.A2502.001
Delta ADP-65DB 3P 65W
AP.T2101.001
Lite-on PA-1650-02CA 3P 65W ABO
AP.T3503.001
Lite-on PA-1650-02CR 3P 65W 19V ABO
AP.06503.002
Delta ADP-65DB 3P 65W w/US Power Cord
AP.A1401.002
Lite-on PA-1650-02CA 3P 65W ABO w/US Power
Cord
AP.T3503.002
116
Description
Keyboard
117
Model Number
Acer P/N
AS2010 (ZIPPY) KEYBOARD US International
KB.A240C.001
AS2010 (ZIPPY) KEYBOARD UK
KB.A240C.002
AS2010 (ZIPPY) KEYBOARD German
KB.A240C.003
AS2010 (ZIPPY) KEYBOARD Italian
KB.A240C.004
AS2010 (ZIPPY) KEYBOARD Chinese
KB.A240C.005
AS2010 (ZIPPY) KEYBOARD French
KB.A240C.006
AS2010 (ZIPPY) KEYBOARD Canadian French
KB.A240C.007
AS2010 (ZIPPY) KEYBOARD Swiss/G
KB.A240C.008
AS2010 (ZIPPY) KEYBOARD Spanish
KB.A240C.009
AS2010 (ZIPPY) KEYBOARD Portuguese
KB.A240C.010
AS2010 (ZIPPY) KEYBOARD Arabic
KB.A240C.011
AS2010 (ZIPPY) KEYBOARD Thai
KB.A240C.012
AS2010 (ZIPPY) KEYBOARD Belgium
KB.A240C.013
AS2010 (ZIPPY) KEYBOARD Sweden
KB.A240C.014
AS2010 (ZIPPY) KEYBOARD Czech
KB.A240C.015
AS2010 (ZIPPY) KEYBOARD Hungaian
KB.A240C.016
AS2010 (ZIPPY) KEYBOARD Norway
KB.A240C.017
AS2010 (ZIPPY) KEYBOARD Danish
KB.A240C.018
AS2010 (ZIPPY) KEYBOARD Russian
KB.A240C.019
AS2010 (JingMold) Keyboard US International
KB.A2405.001
AS2010 (JingMold) Keyboard UK
KB.A2405.002
AS2010 (JingMold) Keyboard German
KB.A2405.003
AS2010 (JingMold) Keyboard Italian
KB.A2405.004
AS2010 (JingMold) Keyboard Chinese
KB.A2405.005
AS2010 (JingMold) Keyboard French
KB.A2405.006
AS2010(JingMold) Keyboard Canadian French
KB.A2405.007
AS2010 (JingMold) Keyboard Swiss/G
KB.A2405.008
AS2010 (JingMold) Keyboard Spanish
KB.A2405.009
AS2010 (JingMold) Keyboard Portuguese
KB.A2405.010
AS2010 (JingMold) Keyboard Arabic
KB.A2405.011
AS2010 (JingMold) Keyboard Thai
KB.A2405.012
AS2010 (JingMold) Keyboard Belgium
KB.A2405.013
AS2010 (JingMold) Keyboard Sweden
KB.A2405.014
AS2010 (JingMold) Keyboard Czech
KB.A2405.015
AS2010 (JingMold) Keyboard Hungaian
KB.A2405.016
AS2010 (JingMold) Keyboard Norway
KB.A2405.017
AS2010 (JingMold) Keyboard Danish
KB.A2405.018
AS2010 (JingMold) Keyboard Russian
KB.A2405.019
Appendix B
Microsoft Windows XP Professional Environment Test
Description
CPU
HDD
Model Number
Intel Pentium-M (Banias) 1.4GHz 1M/400MHz FSB
KC.BS001.14G
Intel Pentium-M (Banias) 1.5GHz 1M/400MHz FSB
KC.BS001.15G
Intel Pentium-M (Banias) 1.6GHz 1M/400MHz FSB
KC.BS001.16G
Intel Pentium-M (Banias) 1.7GHz 1M/400MHz FSB
KC.BS001.17G
Intel Pentium-M (Dothan) 1.6GHz 2M/400MHs FSB
TBD
Intel Pentium-M (Dothan) 1.7GHz 2M/400MHz FSB
KC.ND001.17G
Intel Pentium-M (Dothan) 1.8GHz 2M/400MHz FSB
KC.ND001.18G
HDD 2.5” HGST Moraga IC25N030ATMR04-0
08K0910 30G 4200PRM
08K0910
KH.03007.005
HDD 2.5” Toshiba Pluto MK4025GAS 40GB
4200PRM
MK4025GAS
KH.04004.002
HDD 2.5” HGST Moraga IC25N040ATMR04-0
08K0633 40G 4200PRM (F/W:AD4A)
08K0633
KH.04007.009
HDD 2.5” Seagate N1 ST94019A 2MB 40GB
4200PRM (F/W:3.05)
ST94019A
KH.04001.010
HDD 2.5” HGST Moraga IC25N060ATMR04-0
08K0634 60G 4200RPM(F/W:AD4A)
08K0634
KH.06007.006
HDD 2.5” Toshiba Pluto MK6025GAS 60GB
4200RPM
08K0638
KH.06007.002
HDD 2.5” HGST Moraga IC25N080ATCS04-0
08K0635 80G 4200RPM
08K0635
KH.08007.007
HDD 2.5" HGST Moraga HTS548080M9AT00
08K0639 80G 5400rpm
08K0639
KH.08007.003
Samsung 15.4" WXGA (1280 x 800) TFT Panel
LTN154X1-L02
LK.15406.003
LG 15.4" WXGA (1280 x 800) TFT Panel.
LP154W01-A3
LK.15408.001
AU 15.4" WXGA (1280 x 800) TFT Panel
B154EW01
LK.15405.001
Sanyo 15.4" WXGA (1280 x 800) TFT Panel
TM154WX22L31
LK.1540J.001
QDI 15.4" WXGA (1280 x 800) TFT Panel
QD15TL02-01
LK.15409.001
LG 15.4" WSXGA+ (1600 x 1050) TFT Panel
LP154W02-A1
LK.15408.002
LG 15.4" WSXGA+ (1600 x 1050) TFT Panel
LP154W02-B1
LK.15408.003
Intel 855GME
Intel ICH4-M
Appendix B
KH.06004.003
HDD 2.5” HGST Moraga HTS548060M9AT00
08K0638 60G 5400RPM
LCD Panel
Chipset
Acer P/N
KI.80101.005
118
Description
Model Number
QSI 12.7mm Tray Type DVD/CDRW combo 24/24/
24,8X
SBW-242C (for
Drongo3/4)
KO.02407.013
Pnansonic 12.7mm tray Type DVD/CDRW combo
24/24/24,8X
UJDA750-II (for
Drongo3/4)
KO.02406.004
HLDS 12.7mm Tray Type DVD/CDRW combo 24/24/ GCC-4241N
24,8X
(for Drongo3/4)
KO.02405.001
QSI 12.7mm Tray Type DVD-Dual
SDW-042 (for
Drongo3/4)
KU.00403.002
HLDS 12.7mm Tray Type DVD-Dual
GSA-4040N (for KU.0040D.004
Drongo3/4)
Pnansonic 12.7mm Tray Type Super Multi
UJ820B (for
Drongo3/4)
KU.00407.003
Pnansonic 12.7mm Slot-in DVD/CDRW combo
CW-8123 (for
Drongo2)
KO.02406.005
Pnansonic 12.7mm Slot-in Super Multi
UJ-825 (for
Drongo2)
KU.00407.004
Optical Drive
Memory
Wireless LAN
Acer P/N
Infineon SO-DIMM DDR333 256MB
HYS64D32020GDL-6-B 16x16x8 (0.14u)
KN.25602.009
Infineon SO-DIMM DDR333 512MB
HYS64D64020GBDL-6-C 64Mx64 (0.11u/black)
KN.51202.013
Nanya SO-DIMM DDR333 256MB
NT256D64SH8BAGM-6KE (.14u)
KN.25603.014
Nanya SO-DIMM DDR333 512MB
NT512D64S8HBAFM-6K (.14u)
KN.51203.005
Micron SO-DIMM DDR333 256MB
MT8VDDT3264HDG-335C3 (.13u)
KN.25604.009
Micron SO-DIMM DDR333 256MB MT8VDDT3264H
G-335G3 (0.11u)
KN.25604.014
Micron SO-DIMM DDR 333 512MB
MT16VDDF6464H G-335G2 (0.11u)
KN.51204.012
Intel Wireless LAN, MiniPCI Type 3B Intel 802.11b
KI.CAX01.007
Intel Wireless LAN, MiniPCI Type 3B Intel 802.11b/g
Battery
Mainboard
Adapter
119
AS2010 BATCL32CL 8Cell (Samsung)
BT.A2401.001
AS2010 BATCL32CL 8Cell (Panasonic)
BT.A2401.002
AS2010 BATCL32L4 4Cell (Panasonic)
BT.A2401.003
AS2020 BAT CL32CL 8CELL (Samsung)
BT.A2501.001
AS2020 BAT CL32CL 8CELL (Panasonic)
BT.A2501.002
AS2010 Discrete Mainboard
LB.A2402.001
AS2020 Mainboard
LB.A2502.001
Delta ADP-65DB 3P 65W
AP.T2101.001
Lite-on PA-1650-02CA 3P 65W ABO
AP.T3503.001
Lite-on PA-1650-02CR 3P 65W 19V ABO
AP.06503.002
Delta ADP-65DB 3P 65W w/US Power Cord
AP.A1401.002
Lite-on PA-1650-02CA 3P 65W ABO w/US Power
Cord
AP.T3503.002
Appendix B
Description
Keyboard
Appendix B
Model Number
Acer P/N
AS2010 (ZIPPY) KEYBOARD US International
KB.A240C.001
AS2010 (ZIPPY) KEYBOARD UK
KB.A240C.002
AS2010 (ZIPPY) KEYBOARD German
KB.A240C.003
AS2010 (ZIPPY) KEYBOARD Italian
KB.A240C.004
AS2010 (ZIPPY) KEYBOARD Chinese
KB.A240C.005
AS2010 (ZIPPY) KEYBOARD French
KB.A240C.006
AS2010 (ZIPPY) KEYBOARD Canadian French
KB.A240C.007
AS2010 (ZIPPY) KEYBOARD Swiss/G
KB.A240C.008
AS2010 (ZIPPY) KEYBOARD Spanish
KB.A240C.009
AS2010 (ZIPPY) KEYBOARD Portuguese
KB.A240C.010
AS2010 (ZIPPY) KEYBOARD Arabic
KB.A240C.011
AS2010 (ZIPPY) KEYBOARD Thai
KB.A240C.012
AS2010 (ZIPPY) KEYBOARD Belgium
KB.A240C.013
AS2010 (ZIPPY) KEYBOARD Sweden
KB.A240C.014
AS2010 (ZIPPY) KEYBOARD Czech
KB.A240C.015
AS2010 (ZIPPY) KEYBOARD Hungaian
KB.A240C.016
AS2010 (ZIPPY) KEYBOARD Norway
KB.A240C.017
AS2010 (ZIPPY) KEYBOARD Danish
KB.A240C.018
AS2010 (ZIPPY) KEYBOARD Russian
KB.A240C.019
AS2010 (JingMold) Keyboard US International
KB.A2405.001
AS2010 (JingMold) Keyboard UK
KB.A2405.002
AS2010 (JingMold) Keyboard German
KB.A2405.003
AS2010 (JingMold) Keyboard Italian
KB.A2405.004
AS2010 (JingMold) Keyboard Chinese
KB.A2405.005
AS2010 (JingMold) Keyboard French
KB.A2405.006
AS2010(JingMold) Keyboard Canadian French
KB.A2405.007
AS2010 (JingMold) Keyboard Swiss/G
KB.A2405.008
AS2010 (JingMold) Keyboard Spanish
KB.A2405.009
AS2010 (JingMold) Keyboard Portuguese
KB.A2405.010
AS2010 (JingMold) Keyboard Arabic
KB.A2405.011
AS2010 (JingMold) Keyboard Thai
KB.A2405.012
AS2010 (JingMold) Keyboard Belgium
KB.A2405.013
AS2010 (JingMold) Keyboard Sweden
KB.A2405.014
AS2010 (JingMold) Keyboard Czech
KB.A2405.015
AS2010 (JingMold) Keyboard Hungaian
KB.A2405.016
AS2010 (JingMold) Keyboard Norway
KB.A2405.017
AS2010 (JingMold) Keyboard Danish
KB.A2405.018
AS2010 (JingMold) Keyboard Russian
KB.A2405.019
120
Appendix C
Online Support Information
This section describes online technical support services available to help you repair your Acer Systems.
If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch
office. Acer Branch Offices and Regional Business Units may access our website. However some information
sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
Acer's Website offers you convenient and valuable support resources whenever you need them.
In the Technical Information section you can download information on all of Acer's Notebook, Desktop and
Server models including:
T
Service guides for all models
T
User's manuals
T
Training materials
T
Bios updates
T
Software utilities
T
Spare parts lists
T
TABs (Technical Announcement Bulletin)
For these purposes, we have included an Acrobat File to facilitate the problem-free downloading of our
technical material.
Also contained on this website are:
T
Detailed information on Acer's International Traveler's Warranty (ITW)
T
An overview of all the support services we offer, accompanied by a list of telephone, fax and email
contacts for all your technical queries.
We are always looking for ways to optimize and improve our services, so if you have any suggestions or
comments, please do not hesitate to communicate these to us.
Appendix C
121
Download PDF

advertising