User guide | Aspire Digital 5332 Laptop User Manual

VG27AH
LCD Monitor
User Guide
Table of contents
Notices.......................................................................................................... iii
Safety information....................................................................................... iv
Care & Cleaning............................................................................................ v
1.1Welcome!....................................................................................... 1-1
1.2
Package contents.......................................................................... 1-1
1.3
Monitor introduction..................................................................... 1-2
1.3.1
Front view........................................................................ 1-2
1.3.2
Back view......................................................................... 1-4
1.3.3
Experiencing 3D Virtual Effects....................................... 1-5
2.1
Assembling the monitor base...................................................... 2-1
2.2
Adjusting the monitor................................................................... 2-2
2.3
Detaching the arm (for VESA wall mount).................................. 2-3
3.1
OSD (On-Screen Display) menu.................................................. 3-1
3.1.1
How to configure.............................................................. 3-1
3.1.2
OSD Function Introduction............................................... 3-2
3.2
Specifications................................................................................ 3-8
3.3
Troubleshooting (FAQ)............................................................... 3-10
3.4
Supported Timing List................................................................ 3-11
Copyright © 2012 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless
such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identification or explanation and to the
owners’ benefit, without intent to infringe.
ii
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
As an Energy Star® Partner, our company has determined
that this product meets the Energy Star® guidelines for energy
efficiency.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
iii
Safety information
• Before setting up the monitor, carefully read all the documentation that
came with the package.
• To prevent fire or shock hazard, never expose the monitor to rain or
moisture.
• Never try to open the monitor cabinet. The dangerous high voltages
inside the monitor may result in serious physical injury.
• If the power supply is broken, do not try to fix it by yourself. Contact a
qualified service technician or your retailer.
• Before using the product, make sure all cables are correctly connected
and the power cables are not damaged. If you detect any damage,
contact your dealer immediately.
• Slots and openings on the back or top of the cabinet are provided for
ventilation. Do not block these slots. Never place this product near or
over a radiator or heat source unless proper ventilation is provided.
• The monitor should be operated only from the type of power source
indicated on the label. If you are not sure of the type of power supply to
your home, consult your dealer or local power company.
• Use the appropriate power plug which complies with your local power
standard.
• Do not overload power strips and extension cords. Overloading can
result in fire or electric shock.
• Avoid dust, humidity, and temperature extremes. Do not place the
monitor in any area where it may become wet. Place the monitor on a
stable surface.
• Unplug the unit during a lightning storm or if it will not be used for a
long period of time. This will protect the monitor from damage due to
power surges.
• Never push objects or spill liquid of any kind into the slots on the
monitor cabinet.
• To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked
between 100 ~ 240V AC.
• If you encounter technical problems with the monitor, contact a
qualified service technician or your retailer.
• The socket-outlet shall be installed near the equipment and shall be
easily accessible.
iv
Care & Cleaning
• Before you lift or reposition your monitor, it is better to disconnect the
cables and power cord. Follow the correct lifting techniques when
positioning the monitor. When lifting or carrying the monitor, grasp the
edges of the monitor. Do not lift the display by the stand or the cord.
• Cleaning. Turn your monitor off and unplug the power cord. Clean the
monitor surface with a lint-free, non-abrasive cloth. Stubborn stains
may be removed with a cloth dampened with mild cleaner.
• Avoid using a cleaner containing alcohol or acetone. Use a cleaner
intended for use with the LCD. Never spray cleaner directly on the
screen, as it may drip inside the monitor and cause an electric shock.
The following symptoms are normal with the monitor:
• The screen may flicker during the initial use due to the nature of the
fluorescent light. Turn off the Power Switch and turn it on again to
make sure that the flicker disappears.
• You may find slightly uneven brightness on the screen depending on
the desktop pattern you use.
• When the same image is displayed for hours, an afterimage of the
previous screen may remain after switching the image. The screen will
recover slowly or you can turn off the Power Switch for hours.
• When the screen becomes black or flashes, or cannot work anymore,
contact your dealer or service center to fix it. Do not repair the screen
by yourself!
Conventions used in this guide
WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components
when trying to complete a task.
IMPORTANT: Information that you MUST follow to complete a
task.
NOTE: Tips and additional information to aid in completing a task.
v
Where to find more information
Refer to the following sources for additional information and for product
and software updates.
vi
1.
ASUS websites
The ASUS websites worldwide provide updated information on ASUS
hardware and software products. Refer to http://www.asus.com
2.
Optional documentation
Your product package may include optional documentation that may
have been added by your dealer. These documents are not part of
the standard package.
1.1Welcome!
Thank you for purchasing the ASUS® LCD monitor!
The latest widescreen LCD monitor from ASUS provides a crisper,
broader, and brighter display, plus a host of features that enhance your
viewing experience.
With these features, you can enjoy the convenience and delightful visual
experience that the monitor brings you!
1.2
Package contents
Check your package for the following items:
LCD Monitor
Power Cord
VGA Cable
DVI Cable
3.5mm Audio Cable
FPR 3D Glasses
Quick Start Guide
Warranty Card
If any of the above items is damaged or missing, contact your retailer immediately.
ASUS VG27AH LCD Monitor
1-1
1.3
Monitor introduction
1.3.1
Front view
7
1.
5
4
3
2
1
Power Button/Power Indicator:
•
Press this button to turn the monitor on/off.
•
The color definition of the power indicator is shown below.
2.
Status
Description
Blue
ON
Amber
Standby mode
OFF
OFF
Input Select Button:
•
3.
1-2
6
Press this button to select input source.
Button:
•
Press this button to increase the value of the function selected
or move to the previous function.
•
Brightness hotkey
Chapter 1: Product Introduction
4.
Button:
•
Press this button to enter/select the icon (function) highlighted
while the OSD menu is activated.
•
Exits the hotkey OSD menu.
5.
Button:
•
Press this button to decrease the value of the function selected
or move to the next functions.
•
This is also a hot key for Volume adjustment.
•
Press this hotkey to turn on/off the “2D to 3D” function for 2D
input images.
6.
Button:
2D to 3D:
OFF
Menu: Exit
7.
/
Button:
•
Press this hotkey to switch from six video preset modes
(Scenery Mode, Standard Mode, Theater Mode, Game
Mode, Night View Mode, and sRGB ) with SPLENDID™ Video
Intelligence Technology.
•
Exits the OSD menu or goes back to the previous menu when
the OSD menu is active.
•
Long press this button to automatically adjust this monitor to its
optimized position, clock, and phase (for VGA mode only).
ASUS VG27AH LCD Monitor
1-3
1.3.2
Back view
8
1
2
3
4
5
6
7
Rear connectors
1.
Kensington lock slot.
2.
AC-IN port: This port connects the power cord.
3.
HDMI-IN port: This port is for connection with an HDMI compatible
device.
support 3D graphic card HDMI1.4; DVD player HDMI1.4, and Blu-ray 3D
4.
DVI port: This 24-pin port is for PC (Personal Computer) DVI-D digital
signal connection.
5.
VGA port: This 15-pin port is for PC VGA connection.
6.
PC Audio-In Jack: This 3.5mm stereo jack is for PC audio connection.
7.
Earphone-Out Jack: This 3.5mm stereo jack is for earphone audio
connection.
8.
Screw Holes for VESA Wall Mount
The “2D to 3D” feature is supported through every input port.
The “Real 3D” feature is supported through the HDMI-IN port only.
1-4
Chapter 1: Product Introduction
1.3.3
Experiencing 3D Virtual Effects
This monitor is a 3D LCD monitor which can support HDMI 1.4 3D video or
generate 3D effect by turning on 2D/3D converter function.
The video formats supported for 3D effect of HDMI input are “Side by Side(Half)”
“Top-and-Bottom”, and “Frame Packing”. Please refer to Section 3.4 for supported
timing list.
To connect the HDMI cable
Connect a HDMI cable to the monitor and your 3D compatible device. You
can playback 3D content and enjoy 3D effect on VG27AH LCD monitor.
To support 3D effect, please make sure the HDMI cable is properly connected the
monitor and your 3D compatible device.
ASUS VG27AH LCD Monitor
1-5
2.1
Assembling the monitor base
To assemble the monitor base:
1.
Attach the base to the arm.
2.
Fix with the screws to joint the base with the arm. You can easily
tighten the screws by fingers.
3.
Remove the height adjustment lock from the arm.
1
2
3
The height adjustment lock should NEVER be removed BEFORE you place the
monitor VERTICALLY on a flat and clean table.
2-1
Chapter 2: Setup
2.2
Adjusting the monitor
• For optimal viewing, we recommend that you look at the full face of the
monitor, then adjust the monitor to the angle that is most comfortable
for you.
• Hold the base to prevent the monitor from falling when you change its
angle.
• You can tilt the monitor’s from -5˚ to +15˚, swivel from left-to-right for
150˚, and lift the monitor’s height for about 100mm.
-5° ~ +15°
150°
150°
0°
100mm
It is normal that the monitor slightly shakes while you adjust the viewing angle.
ASUS VG27AH LCD Monitor
2-2
2.3
Detaching the arm (for VESA wall
mount)
The detachable arm of this monitor is specially designed for VESA wall
mount.
To detach the arm:
2-3
1.
Disconnect power and signal cables.
2.
Lower the monitor to its lowest height, and then insert the height
adjustment lock.
3.
Carefully put the front of the monitor face down on a flat and clean
table.
4.
Use a screwdriver to remove the four screwdrivers on the arm (Figure
1), and then detach the arm from the monitor (Figure 2).
•
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
•
Hold the stand while removing the screws.
•
The VESA wall mount kit ( 100 x 100 mm) is purchased separately.
•
Use only the UL Listed Wall Mount Bracket with minimum weight/load 28 kg
(Screw size: M4 x 12 mm).
Chapter 2: Setup
3.1
OSD (On-Screen Display) menu
3.1.1
How to configure
VG27A
Splendid
Scenery Mode
Color
Standard Mode
Image
Theater Mode
Input Select
Game Mode
System Setup
Night View Mode
sRGB
Move
Menu
Exit
1.
Press [
] button to activate the OSD menu.
2.
Press [
] or [
] button to navigate through the functions.
Highlight and activate the desired function by pressing [
]
button. If there is a sub-menu in the function selected, press [
]
or [
] button again to navigate through the sub-menu functions.
Highlight and activate the desired sub-menu function by pressing
[
] button.
3.
Press [
function.
4.
To exit the OSD menu, press [
3 to adjust any other function.
] or [
ASUS VG27AH LCD Monitor
] button to change the settings of the selected
/
] button. Repeat step 2 and step
3-1
3.1.2
1.
OSD Function Introduction
Splendid
This function contains six sub-functions you can select for your
preference. Each mode has the Reset selection, allowing you to
maintain your setting or return to the preset mode.
VG27A
Splendid
Scenery Mode
Color
Standard Mode
Image
Theater Mode
Input Select
Game Mode
System Setup
Night View Mode
sRGB
Move
3-2
Menu
Exit
•
Scenery Mode: The best choice for scenery photo display with
SPLENDID™ Video Intelligence Technology.
•
Standard Mode: The best choice for document editing with
SPLENDID™ Video Intelligence Technology.
•
Theater Mode: The best choice for movie with SPLENDID™
Video Intelligence Technology.
•
Game Mode: The best choice for game playing with
SPLENDID™ Video Intelligence Technology.
•
Night View Mode: The best choice dark-scene game or movie
with SPLENDID™ Video Intelligence Technology.
•
sRGB Mode: Compatible with sRGB color space. sRGB mode
is the best choice for document editing.
•
In the Standard Mode, the Saturation and ASCR functions are not userconfigurable.
•
In the other modes, the sRGB function is not user-configurable.
Chapter 3: OSD (On-Screen Display) Menu
2.
Color
Set a desired color setting from this menu.
VG27A
Splendid
Brightness
90
Color
Contrast
80
Image
Saturation
Input Select
Color Temp.
System Setup
Skin Tone
Move
Menu
50
User Mode
Natural
Exit
•
Brightness: The adjusting range is from 0 to 100. The
button is a hotkey to activate this function.
•
Contrast: The adjusting range is from 0 to 100.
•
Saturation: The adjusting range is from 0 to 100.
•
Color Temp.: Contains four color modes: “Cool”, “Normal”,
“Warm”, and “User Mode”.
In the User mode for Color Temp., the colors of R (Red), G (Green), and B (Blue)
are user-configurable; the adjusting range is from 0 to 100.
•
3.
Skin Tone: Contains three color modes including “Reddish”,
“Natural”, and “Yellowish”.
Image
Set the image related setting from this menu.
VG27A
Splendid
Sharpness
0
Color
Trace Free
60
Image
Aspect Control
Full
Input Select
ASCR
OFF
System Setup
3D Mode Selection
5
3D Depth
Position
Focus
Move
ASUS VG27AH LCD Monitor
Menu
Exit
3-3
3-4
•
Sharpness: Adjust the picture sharpness. The adjusting range
is from 0 to 100.
•
Trace Free: Speed up the response time. The adjusting range is
from 0 to 100.
•
Aspect Control: Adjust the aspect ratio to “4:3”, “Full”, or
“OverScan”. (The “OverScan” ratio is only available for HDMI
input.)
•
ASCR: Turn on or off the ASCR (ASUS Smart Contrast Ratio)
function. (Only available at Scenery, Theater, Game, and Night
View Mode.)
•
3D Mode Selection: Select the type for 3D images.
•
Default: Turn “2D to 3D” function off.
•
2D to 3D: Turn “2D to 3D” function on for 2D input images
(you may also press the hotkey
to access this function).
•
3D Top-and-Bottom, 3D Side-by-Side (Half): Select the
type for incoming 3D images.
•
The menu “3D Mode Selection” is only available for input source of 2D type.
•
The menu “3D Top-and-Bottom” and “3D Side-by-Side (Half)” are only
available for HDMI source of 720p/1080i/1080p timing and no InfoFrame of
3D type.
•
3D Depth: Adjust the field depth for 3D images. The adjusting
range is from 1 to 10.
•
Position: Adjust the horizontal position (H-Position) and the
vertical position (V-Position) of the image. The adjusting range is
from 0 to 100. (Only available for VGA input.)
•
Focus: Reduce Horizontal-line noise and Vertical-line noise
of the image by adjusting (Phase) and (Clock) separately. The
adjusting range is from 0 to 100. (Only available for VGA input.)
•
Phase adjusts the phase of the pixel clock signal. With a wrong phase
adjustment, the screen shows horizontal disturbances.
•
Clock (pixel frequency) controls the number of pixels scanned by one
horizontal sweep. If the frequency is not correct, the screen shows vertical
stripes and the image is not proportional.
Chapter 3: OSD (On-Screen Display) Menu
4.
Input Select
Select the input source from “VGA”, “DVI”, “HDMI 1”, or “HDMI 2”.
VG27A
Splendid
VGA
Color
DVI
Image
HDMI 1
Input Select
HDMI 2
System Setup
Move
5.
Menu
Exit
System Setup
Adjust the system configuration.
VG27A
Splendid
Splendid Demo Mode
Color
Volume
Image
ECO Mode
Input Select
QuickFit
System Setup
OSD Setup
OFF
50
OFF
Language
English
Information
All Reset
Move
Menu
Exit
•
Splendid Demo Mode: Splits the screen into two for Splendid
modes comparison. (Only available at Scenery Mode, Theater
Mode, Game Mode, and Night View Mode.)
•
Volume: Adjusts the speaker and earphone output volume
level. The adjusting range is from 0 to 100.
•
ECO Mode: Activate the ecology mode for power saving. (Some
gray levels may not be distinguished if ECO is ON. Its brightness
is lower than that when setting the Contrast Ratio to 100.)
•
QuickFit: Contains three patterns: (1) Grid pattern, (2) Paper
size, (3) Photo size.
ASUS VG27AH LCD Monitor
3-5
1.
Grid pattern: Facilitates designers and users to organize
content and layout on one page and achieve a consistent
look and feel.
Alignment Grid
2.
Paper size: Provides users to view their documents in real
size on the screen.
A4
Letter
3.
Photo size: Provides photographers and other users to
accurately view and edit their photos in real size on the
screen.
4x6
3-6
3x5
2x2
Chapter 3: OSD (On-Screen Display) Menu
8x10
•
5x7
OSD Setup:
•
H-Position / V-Position: Adjusts the horizontal position
(H-Position) or the vertical position (V-Position) of the OSD
from 0 to 100.
•
OSD Timeout: Adjusts the OSD timeout from 10 to 120
seconds.
•
DDC/CI: Enables or disables the DDC/CI function.
•
Transparency: Adjusts the OSD background from opaque
to transparent.
•
Language: There are 17 languages for your selection,
including “English”, “French”, “German”, “Spanish”, “Italian”,
“Dutch”, “Russian”, “Traditional Chinese”, “Simplified Chinese”,
“Japanese”, “Polish”, “Turkish”, “Portuguese”, “Czech”,
“Croatian”, “Hungarian”, and “Romanian”.
•
Information: Shows the monitor information.
•
All Reset: Select “Yes” to restore the default settings.
ASUS VG27AH LCD Monitor
3-7
3.2
3-8
Specifications
Panel Type
TFT LCD
Panel Size
27” W (68.6 cm)
Color Saturation(NTSC)
≧ 72% (sRGB)
True Resolution
1920 x 1080
Full HD 1080P
Yes
Pixel Pitch
0.3114 mm
Brightness (Typ.)
250 cd/m2
Contrast Ratio (Typ.)
≧ 1000:1
ASUS Smart Contrast Ratio (ASCR)
≧ 80,000,000:1 (with ASCR on)
Viewing Angle (H/V) CR≧10
178°(H) /178°(V)
Display Colors
≧ 16.7 M
Response Time
≦ 5 ms (Gray to gray)
Trace Free Technology
Yes
SPLENDID™ Video Intelligence
Technology
Yes
SPLENDID™ Selection
6 video preset modes (by hotkey)
Skin-Tone Selection
3 modes
Color Temperature Selection
4 modes (9300K/7500K/6500K/User Mode)
HDCP
Yes
Stereo Speaker
3 W x 2 stereo, RMS
Auto Adjustment Hotkey
Yes
Brightness Adjustment Hotkey
Yes
Volume Adjustment Hotkey
Yes
Input Selection Hotkey
Yes
2D-to-3D Hotkey
Yes
PC Input
DVI, D-Sub
PC Audio Input
Yes (3.5 mm Mini-jack)
Video Input
HDMI 1.4 (support Blu-ray 3D)
AV Audio Input
HDMI 1.4
Earphone Jack
Yes (3.5 mm Mini-jack)
Chassis Colors
Black
Power LED
Blue (On) / Amber (Standby)
Tilt
+15˚ ~ -5˚
Swivel
+150˚ ~ -150˚
Chapter 3: OSD (On-Screen Display) Menu
Height Adjustment
100 mm
VESA Wall Mounting
100 x 100 mm
Kensington Lock
Yes
AC Input Voltage
AC: 100 ~ 240V
Power Consumption
Power On: < 45 W (Max.)
Energy Star: < 37.25 W
Standby: < 1 W
Power Off: < 1 W
Temperature (Operating)
0˚C ~ +35˚C
Temperature (Non-operating)
-20˚C ~ +60˚C
Dimension (W x H x D)
643 x 438 x 250 mm (machine)
711 x 540 x 227 mm (package)
Weight (Esti.)
8.3 kg (Net); 11.8 kg (Gross)
Regulation approvals
Energy Star 5.0, UL/cUL, CB, CE, ErP,
FCC, CCC, BSMI, Gost-R, C-Tick, VCCI,
J-MOSS, PSE, RoHS, WEEE, Windows 7
WHQL, Green ASUS
*Specifications subject to change without notice.
ASUS VG27AH LCD Monitor
3-9
3.3
Troubleshooting (FAQ)
Problem
Power LED is not ON
Possible Solution
• Press the button to check if the monitor is in the
ON mode.
• Check if the power cord is properly connected to
the monitor and the power outlet.
The power LED lights amber and • Check if the monitor and the computer are in the
there is no screen image
ON mode.
• Make sure the signal cable is properly connected
the monitor and the computer.
• Inspect the signal cable and make sure none of the
pins are bent.
• Connect the computer with another available
monitor to check if the computer is properly
working.
Screen image is too light or dark
• Adjust the Contrast and Brightness settings via
OSD.
Screen image bounces or a wave • Make sure the signal cable is properly connected to
pattern is present in the image
the monitor and the computer.
• Move away electrical devices that may cause
electrical interference.
3-10
Screen image has color defects
(white does not look white)
• Inspect the signal cable and make sure that none of
the pins are bent.
• Perform All Reset via OSD.
• Adjust the R/G/B color settings or select the Color
Temperature via OSD.
3D function is not working well
• For “2D to 3D”: Press the “2D to 3D” hot key
[ ] to turn on this function if the input image is 2D.
Adjust “3D Depth” in the OSD menu to adjust 3D
performance.
• For Real 3D: Make sure the input source is HDMI,
and the cable is connected. DVI & VGA are not
supported for Real 3D function.
• Make sure your graphics card or DVD player
support HDMI 1.4.
• Make sure the 3D glasses is used for this monitor.
• Make sure the computer was installed with
Microsoft® Windows Vista or Windows 7 operating
system, and with application of 3D media player.
Chapter 3: OSD (On-Screen Display) Menu
3.4
Supported Timing List
Resolution
640x480
640x480
640x480
720x400
800x600
800x600
800x600
800x600
832x624
848x480
1024x768
1024x768
1024x768
1152x864
1280x720
1280x720
1280x720
1280x768
1280x800
1280x800
1280x800
1280x960
1280x1024
1280x1024
1366x768
1440x900
1440x900
1440x900
1680x1050
1680x1050
1920x1080
1920x1080
640x480P (HDMI)
720x480P (HDMI)
ASUS VG27AH LCD Monitor
Refresh Rate
60Hz
67Hz
75Hz
70Hz
56Hz
60Hz
72Hz
75Hz
75Hz
60Hz
60Hz
70Hz
75Hz
75Hz
60Hz
60Hz
75Hz
60Hz
60Hz
60Hz
75Hz
60Hz
60Hz
75Hz
60Hz
60Hz
60Hz
75Hz
60Hz
60Hz
60Hz
60Hz
59.94/60Hz
59.94/60Hz
Horizontal
31.469KHz
35KHz
37.5KHz
31.469KHz
35.156KHz
37.879KHz
48.077KHz
46.875KHz
49.725KHz
31.02KHz
48.363KHz
56.476KHz
60.023KHz
67.5KHz
44.444KHz
44.772KHz
56.456KHz
47.396KHz
49.306KHz
49.702KHz
62.795KHz
60KHz
63.981KHz
79.976KHz
47.712KHz
55.935KHz
55.469KHz
70.635KHz
64.674KHz
65.29KHz
67.5KHz
66.587KHz
31.469KHz/31.5KHz
31.469KHz/31.5KHz
3-11
Resolution
720x576P (HDMI)
1280x720P (HDMI)
1280x720P (HDMI)
1440x480P (HDMI)
1440x576P (HDMI)
1920x1080i (HDMI)
1920x1080i (HDMI)
1920x1080P (HDMI)
1920x1080P (HDMI)
Refresh Rate
50Hz
50Hz
59.94/60Hz
59.94/60Hz
50Hz
50Hz
59.94/60Hz
50Hz
59.94/60Hz
Horizontal
31.25KHz
37.5KHz
44.955KHz/45KHz
31.469KHz/31.5KHz
31.25KHz
28.125KHz
33.716KHz/33.75KHz
56.25KHz
67.433 KHz/67.5KHz
3D Display Modes, Primary Timings List (HDMI input only)
Mode
720P
1080i
3D Video Format
Frame Packing
Side by Side(Half)
Top-and-Bottom
Resolution
1280x720P 50Hz
Side by Side(Half)
Top-and- Bottom
1920x1080i 50Hz
1920x1080i 59.94/60Hz
1920x1080P 50Hz
1920x1080P 59.94/60Hz
1920x1080P 23.98/24Hz
Side by Side(Half)
Top-and-Bottom
1080P
3-12
Frame Packing
Side by Side(Half)
Top-and-Bottom
1280x720P 59.94/60Hz
1920x1080P 30Hz
Chapter 3: OSD (On-Screen Display) Menu
Download PDF

advertising