Technical information | Aspire Digital 7730G Laptop User Manual

Aspire 7730/7730G Series
Service Guide
Service guide files and updates are available
on the ACER/CSD web; for more information,
please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates made on Aspire 7730/7730G Series service guide.
Date
II
Chapter
Updates
Copyright
Copyright © 2008 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
III
Conventions
The following conventions are used in this manual:
IV
SCREEN MESSAGES
Denotes actual messages that appear
on screen.
NOTE
Gives bits and pieces of additional
information related to the current
topic.
WARNING
Alerts you to any damage that might
result from doing or not doing specific
actions.
CAUTION
Gives precautionary measures to
avoid possible hardware or software
problems.
IMPORTANT
Reminds you to do specific actions
relevant to the accomplishment of
procedures.
Preface
Before using this information and the product it supports, please read the following general information.
1.
This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's "global" product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2.
Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.
V
VI
Table of Contents
System Specifications
1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Your Acer Notebook tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Closed Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Left View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Right View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Easy-Launch Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Touch Pad Basics (with fingerprint reader) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Using the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Lock Keys and embedded numeric keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Windows Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Special Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Using the System Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Acer GridVista (dual-display compatible) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Launch Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Hardware Specifications and Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
System Utilities
27
BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Navigating the BIOS Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
BIOS Flash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Remove HDD/BIOS Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Machine Disassembly and Replacement
43
Disassembly Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Pre-disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
External Module Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
External Modules Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Removing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Removing the SD dummy card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Removing the ExpressCard dummy card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Removing the Lower Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Removing the DIMM Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Removing the MXM Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Removing the Turbo RAM module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Removing the TV Tuner module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Removing the WLAN Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Removing the Hard Disk Drive1 Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Removing the Hard Disk Drive2 Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
VII
Table of Contents
Removing the Optical Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Main Unit Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Main Unit Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Removing the Switch Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Removing the Switch Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Removing the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Removing the Modem Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Removing the Antenna, MIC and Speaker Cables . . . . . . . . . . . . . . . . . . . . . . .67
Removing the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Removing the Upper Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Removing the Touch Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Removing the Finger Print Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Removing the Launch Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Removing the Speaker Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Removing the eKey Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Removing the Bluetooth board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Removing the Subwoofer Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Removing the ExpressCard Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Removing the Mainboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Removing the CPU Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Removing the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
LCD Module Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
LCD Module Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Removing the LCD Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Removing the Inverter Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Removing the Camera Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
Removing the LCD Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
Removing the LCD Brackets and FPC Cable . . . . . . . . . . . . . . . . . . . . . . . . . . .94
LCD Module Reassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
Replacing the LCD Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
Replacing the LCD Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Main Module Reassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Replacing the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Replacing the CPU Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Replacing the Mainboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Replacing the Bluetooth Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
Replacing the ExpressCard Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
Replacing the Subwoofer Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103
Replacing the Finger Print Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
Replacing the eKey Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
Replacing the Touch Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
Replacing the Launch Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
Replacing the Switch Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
Replacing the Antenna, MIC and Speaker Cables . . . . . . . . . . . . . . . . . . . . . .109
Replacing the Speaker Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
Replacing the Upper Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
Replacing the Modem Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
Replacing the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116
Replacing the Switch Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
Replacing the ODD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118
Replacing the Hard Disk Drive2 Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Replacing the Hard Disk Drive1 Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
Replacing the WLAN Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121
Replacing the TV Tuner Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
Replacing the Turbo Ram Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123
VIII
Table of Contents
Replacing the MXM Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123
Replacing the DIMM Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124
Replacing the Lower Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124
Replacing the ExpressCard Dummy Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125
Replacing the SD Dummy Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125
Replacing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125
Troubleshooting
127
Common Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127
Power On Issue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128
No Display Issue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129
Random Loss of BIOS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130
LCD Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131
Built-In Keyboard Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131
Touch Pad Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132
Internal Speaker Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132
Internal Microphone Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
HDD Not Operating Correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .135
ODD Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136
USB Failure (Rightside) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .139
Modem Function Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .139
Wireless Function Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140
EasyTouch Button Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140
MediaTouch Button Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .141
Fingerprint Reader Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .141
Thermal Unit Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .142
HDTV Switch Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .142
External Mouse Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .143
Other Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .143
Intermittent Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144
Undetermined Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144
POST Codes Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145
Chipset POST Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145
Core POST Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147
Jumper and Connector Locations
155
Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156
Clearing Password Check and BIOS Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . .157
Clearing Password Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157
BIOS Recovery by Crisis Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158
FRU (Field Replaceable Unit) List
159
Aspire 7730/7730G Exploded Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160
Upper Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160
Lower Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161
LCD Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .162
Model Definition and Configuration
170
Aspire 7730/7730G Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .170
Test Compatible Components
193
Microsoft® Windows® Vista Environment Test . . . . . . . . . . . . . . . . . . . . . . . . . . . .194
PCMCIA LAN Card Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .194
Express Card Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .194
IX
Table of Contents
Display Port Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .194
USB Port Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .194
Access Point Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .195
Bluetooth Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .195
Card Reader Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .196
Audio Jacks Port Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .196
Port Replicator Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .196
Online Support Information
197
Index
199
X
Chapter 1
System Specifications
Features
Below is a brief summary of the computer’s many feature:
Operating System
•
Windows® Vista™
Platform
•
Intel® Centrino® 2 processor technology, featuring:
•
Intel® Core™2 Duo processor*
•
Mobile Intel® PM45/GM45 Express Chipset*
•
Intel® Wireless WiFi Link 5100/5300, 5150/5350*
System Memory
•
Dual-Channel DDR2 SDRAM support
•
Up to 2 GB of DDR2 667 MHz memory, upgradeable to 4 GB using two soDIMM modules*
TV Tuner
•
Digital TV-tuner supporting DVB-T*
Display and graphics
•
14.1" WXGA 1280 x 800
•
Mobile Intel® GM45 Express Chipset
•
NVIDIA GeForce 9300M GS / 9600M GT*
Storage subsystem
•
2.5" hard disk drive
•
Optical drive options:
•
Blu-ray Disc™ /DVD-Super Multi double-layerdrive
•
DVD-Super Multi double-layer drive
•
5-in-1 card reader
•
Dolby-certified surround sound system with two built-in stereo speakers and one subwoofer
supporting low-frequency effects
•
S/PDIF (Sony/Philips Digital Interface) support for digital speakers
•
Acer PureZone technology with two built-in stereo microphones
Audio
Chapter 1
1
Dimensions and Weight
•
340.4 (W) x 247 (D) x 22.9/42.3 (H) mm (13.4 x 9.7 x 0.9/1.6 inches)
•
2.4 kg (5.29 lbs.)
Communication
•
Acer Video Conference, featuring:
•
Integrated Acer Crystal Eye webcam
•
Acer Video Conference Manager software
•
Acer PureZone technology
•
Optional Acer Xpress VoIP phone
•
WLAN: Intel® Wireless WiFi Link 5100/5300*
•
WiFi®/WiMAX™: Intel® Wireless WiFi Link 5150/5350*
•
WPAN: Bluetooth® 2.0+EDR (Enhanced Data Rate)
•
LAN: Gigabit Ethernet; Wake-on-LAN ready
•
Modem: 56K ITU V.92
Privacy control
•
Acer Bio-Protection fingerprint solution
•
BIOS user, supervisor, HDD passwords
•
Kensington lock slot
Power subsystem
•
ACPI 3.0
•
48.8 W 4400 mAh*
•
3-pin 90 W AC adapter*
•
3-pin 65 W AC adapter*
•
Energy Star 4.0
Special keys and controls
•
88-/89-/93-key keyboard
•
Touch Pad pointing device
•
Empowering Key
•
Easy-launch buttons: WLAN, Internet, email, Bluetooth, Acer Arcade™
•
Acer MediaTouch keys: play/pause, stop, previous, next and record keys
•
Volume wheel
•
Acer Media Center remote control*
I/O interface
2
•
Acer EasyPort IV connector
•
ExpressCard™/54 slot
•
5-in-1 card reader (SD/MMC/MS/MS PRO/xD)
Chapter 1
•
3 USB 2.0 ports
•
HDMI™ port with HDCP support
•
Consumer infrared (CIR) port
•
External display (VGA) port
•
Headphones/speaker/line-out port with S/PDIF support
•
Microphone-in jack
•
Line-in jack
•
Ethernet (RJ-45) port
•
Modem (RJ-11) port
•
DC-in jack for AC adapter
Environment
•
•
Temperature:
•
Operating: 5 °C to 35 °C
•
Non-operating: -20 °C to 65 °C
Humidity (non-condensing):
•
Operating: 20% to 80%
•
Non-operating: 20% to 80%
NOTE: Items marked with * denote only selected models.
Chapter 1
3
System Block Diagram
4
Chapter 1
Your Acer Notebook tour
After knowing your computer features, let us show you around your new computer.
Front View
No.
Icon
Item
Description
1
Acer PureZone
Two internal stereo microphones for sound
recording.
2
Acer Crystal Eye
Web camera for video communication.
3
Display screen
Also called Liquid-Crystal Display (LCD),
displays computer output.
4
Status indicators
Light-Emitting Diodes (LEDs) that light up to
show the status of the computer's functions
and components.
5
Empowering key
Launch Acer Empowering Technology
6
Easy-launch
buttons
Buttons for launching frequently used program.
7
Palmrest
Comfortable support area for your hands when
you use the computer.
8
Touch Pad
Touch-sensitive pointing device which functions
like a computer mouse.
Chapter 1
5
No.
Icon
Item
Description
9
Click buttons
(left, center* and
right)
The left and right buttons function like the left
and right mouse buttons. *The center button
serves as Acer Bio-Protection fingerprint
reader supporting Acer FingerNav 4-way
control function.
10
Status indicators
Light-Emitting Diodes (LEDs) that light up to
show the status of the computer's functions
and components.
11
Keyboard
For entering data into your computer.
12
Speakers
Left and right speakers deliver stereo audio
output.
13
Acer MediaTouch
keys
For use with Acer Arcade and other media
playing programs.
14
Power button
Turns the computer on and off.
Closed Front View
No.
6
Icon
Item
Description
1
CIR receiver
Receives signals from a remote control.
2
5-in-1 card
reader
Accepts Secure Digital (SD), MultiMediaCard
(MMC), Memory Stick (MS), Memory Stick
PRO (MS PRO), xD-Picture Card (xD).
3
Latch
Locks and releases the lid
Chapter 1
Left View
No.
Icon
Item
Description
1
Acer EasyPort IV
connector
Connects to Acer EasyPort IV.
2
Ethernet (RJ-45)
port
Connects to an Ethernet 10/100/1000-based
network.
3
External display
(VGA) port
Connects to a display device
(e.g. external monitor, LCD projector).
HDMI
Connects to a television or display device with
HDMI input.
5
USB 2.0 ports
Connect to USB 2.0 devices (e.g. USB mouse,
USB camera).
6
Line-in jack
Accepts audio line-in devices (e.g. audio CD
player, stereo walkman).
7
Microphone-in
jack
Accepts input from external microphones.
8
Headphones/
speaker/line-out
jack with S/PDIF
support
Connects to audio line-out devices
(e.g. speakers, headphones).
9
Unlimited volume
control wheel
Adjust the volume of the audio-out.
10
ExpressCard/54
slot
Accepts one ExpressCard/54 module.
4
Chapter 1
HDMI
7
Right View
No.
Icon
Item
Description
1
Kensington lock
slot
Connects to a Kensington-compatible computer
security lock.
2
Optical drive
Internal optical drive; accepts CDs or DVDs.
3
Optical disk access
indicator
Lights up when the optical drive is active.
4
Optical drive eject
button
Ejects the optical disk from the drive.
5
Emergency eject
hole
Ejects the optical drive tray when the computer is
turned off. Note: Insert a paper clip into the
emergency eject hole to eject the optical drive
tray when the computer is off.
6
Modem (RJ-11)
port
Connects to a phone line.
7
USB 2.0 port
Connect to USB 2.0 devices (e.g. USB mouse,
USB camera).
8
DC-in jack
Connects to an AC adapter
Rear View
No.
1
8
Icon
Item
Ventilation slots
Description
Enable the computer to stay cool, even after
prolonged use.
Chapter 1
Bottom View
No.
Icon
Item
Description
1
Battery bay
Houses the computer's battery pack.
2
Battery release
latch
Releases the battery for removal.
3
Memory
compartment
Houses the computer's main memory.
4
Hard disk bay
Houses the computer's hard disk (secured with
screws).
5
Battery lock
Locks the battery in position.
6
Ventilation slots
and cooling fan
Enable the computer to stay cool, even after
prolonged use.
Note: Do not cover or obstruct the opening of the
fan.
Chapter 1
9
Indicators
The computer has several easy-to-read status indicators. The front panel indicators are visible even when the
computer cover is closed.
Icon
Function
Description
Power
Indicates the computer's power status.
Battery
Indicates the computer's battery status.
HDD
Indicates when the hard disk drive is active.
Num Lock
Lights up when Num Lock is activated.
Caps Lock
Lights up when Caps Lock is activated.
NOTE: 1. Charging: The light shows amber when the battery is charging. 2. Fully charged: The light shows
green when in AC mode.
Easy-Launch Buttons
Located beside the keyboard are application buttons. These buttons are called easy-launch buttons. They are:
WLAN, Internet, email, Bluetooth, Arcade and Acer Empowering Technology.
The mail and Web browser buttons are pre-set to email and Internet programs, but can be reset by users. To
set the Web browser, mail and programmable buttons, run the Acer Launch Manager.
Icon
10
Function
Description
Empowering Technology
Launch Acer Empowering Technology.
(user-programmable)
Acer Arcade
Launch Acer Arcade utility
Wireless communication
button/indicator
Enables/disables the wireless function. Indicates
the status of wireless LAN communication.
Web browser
Internet browser (user-Programmable)
Mail
Email application (user-Programmable)
Bluetooth communication
button/indicator
Enables/disables the Bluetooth function. Indicates
the status of Bluetooth communication.
Chapter 1
Touch Pad Basics (with fingerprint reader)
The following items show you how to use the Touch Pad with Acer Bio-Protection fingerprint reader:
•
Move your finger across the Touch Pad (2) to move the cursor.
•
Press the left (1) and right (4) buttons located beneath the Touch Pad to perform selection and
execution functions. These two buttons are similar to the left and right buttons on a mouse.
Tapping on the Touch Pad is the same as clicking the left button.
•
Use Acer Bio-Protection fingerprint reader (3) supporting Acer FingerNav 4-way control function
(only for certain models) or the 4-way scroll (3) button (only for certain models) to scroll up or down
and move left or right a page. This fingerprint reader or button mimics your cursor pressing on the
right scroll bar of Windows applications.
Function
Execute
Left Button (1)
Right Button (3)
Quickly click twice.
Main Touch Pad (2)
Tap twice (at the same speed
as double-clicking a mouse
button).
Select
Click once.
Tap once.
Drag
Click and hold, then use
finger on the Touch Pad to
drag the cursor.
Tap twice (at the same speed
as double-clicking a mouse
button); rest your finger on
the Touch Pad on the second
tap and drag the cursor.
Access
context menu
Click once.
NOTE: When using the Touch Pad, keep it - and your fingers - dry and clean. The Touch Pad is sensitive to
finger movement; hence, the lighter the touch, the better the response. Tapping too hard will not
increase the Touch Pad’s responsiveness.
Chapter 1
11
Using the Keyboard
The keyboard has full-sized keys and an embedded numeric keypad, separate cursor, lock, Windows, function
and special keys.
Lock Keys and embedded numeric keypad
The keyboard has three lock keys which you can toggle on and off.
Lock key
Description
Caps Lock
When Caps Lock is on, all alphabetic characters typed are in uppercase.
Num Lock
<Fn> + <F11>
When Num Lock is on, the embedded keypad is in numeric mode. The keys
function as a calculator (complete with the arithmetic operators +, -, *, and /). Use
this mode when you need to do a lot of numeric data entry. A better solution
would be to connect an external keypad.
Scroll Lock <Fn> +
<F12>
When Scroll Lock is on, the screen moves one line up or down when you press
the up or down arrow keys respectively. Scroll Lock does not work with some
applications.
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters
located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols
are not printed on the keys.
Desired access
12
Num Lock on
Num Lock off
Number keys on
embedded keypad
Type numbers in a normal manner.
Cursor-control keys on
embedded keypad
Hold <Shift> while using cursorcontrol keys.
Hold <Fn> while using cursorcontrol keys.
Main keyboard keys
Hold <Fn> while typing letters on
embedded keypad.
Type the letters in a normal
manner.
Chapter 1
Windows Keys
The keyboard has two keys that perform Windows-specific functions.
Key
Description
Windows key Pressed alone, this key has the same effect as clicking on the Windows Start button;
it launches the Start menu. It can also be used with other keys to provide a variety of
functions:
<
>:
Open or close the Start menu
<
>
+ <D>: Display the desktop
<
>
+ <E>: Open Windows Explore
<
>
+ <F>: Search for a file or folder
<
>
+ <G>: Cycle through Sidebar gadgets
<
>
+ <L>: Lock your computer (if you are connected to a network domain), or
switch users (if you're not connected to a network domain)
<
>
+ <M>: Minimizes all windows
<
>
+ <R>: Open the Run dialog box
<
>
+ <T>: Cycle through programs on the taskbar
<
>
+ <U>: Open Ease of Access Center
<
>
+ <X>: Open Windows Mobility Center
<
>
+ <BREAK>: Display the System Properties dialog box
<
>
+ <SHIFT+M>: Restore minimized windows to the desktop
<
>
+ <TAB>: Cycle through programs on the taskbar by using Windows Flip 3-D
<
>
+ <SPACEBAR>: Bring all gadgets to the front and select Windows Sidebar
<CTRL> + <
>
<CTRL> + <
>
+ <F>: Search for computers (if you are on a network)
+ <TAB>: Use the arrow keys to cycle through programs on the
taskbar by using Windows Flip 3-D
Note: Depending on your edition of Windows Vista, some shortcuts may not function
as described.
Application
key
Chapter 1
This key has the same effect as clicking the right mouse button; it opens the
application's context menu.
13
Hot Keys
The computer employs hotkeys or key combinations to access most of the computer’s controls like screen
brightness, volume output and the BIOS utility.
To activate hot keys, press and hold the <Fn> key before pressing the other key in the hotkey combination.
Hotkey
14
Icon
Function
Description
<Fn> + <F1>
Hotkey help
Displays help on hotkeys.
<Fn> + <F2>
Acer eSettings
Management
Launches Acer eSettings Management in Acer
Empowering Technology.
<Fn> + <F3>
Acer ePower
Management
Launches Acer ePower Management in Acer
Empowering Technology.
<Fn> + <F4>
Sleep
Puts the computer in Sleep mode.
<Fn> + <F5>
Display toggle
Switches display output between the display
screen, external monitor (if connected) and
both.
<Fn> + <F6>
Screen blank
Turns the display screen backlight off to save
power. Press any key to return.
<Fn> + <F7>
Touch Pad toggle
Turns the internal Touch Pad on and off.
<Fn> + <F8>
Speaker toggle
Turns the speakers on and off.
<Fn> + < >
Brightness up
Increases the screen brightness.
<Fn> + < >
Brightness down
Decreases the screen brightness.
<Fn> + <Home>
Play/Pause
Play/Pause the current media.
<Fn> + <Pg Up>
Stop
Stop the current media.
<Fn> + <Pg Dn>
Skip Backward
Skip to the next track of the current media.
<Fn> + <End>
Skip Forward
Skip top the previous track of the current media.
Chapter 1
Special Key
You can locate the Euro symbol and the US dollar sign at the upper-center and/or bottom-right of your
keyboard.
The Euro symbol
1.
Open a text editor or word processor.
2. Hold <Alt Gr> and then press the <5> key at the upper-center of the keyboard.
NOTE: Note: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/
typography/faq/faq12.htm for more information.
The US dollar sign
1.
Open a text editor or word processor.
2. Hold <Shift> and then press the <4> key at the upper-center of the keyboard.
NOTE: This function varies by the operating system version.
•
Chapter 1
15
Using the System Utilities
Acer Bio-Protection (only for certain models) Acer Bio-Protection Fingerprint Solution is a multi-purpose
fingerprint software package integrated with the Microsoft Windows operating system. Utilizing the uniqueness
of one's fingerprint features, Acer Bio-Protection Fingerprint Solution has incorporated protection against
unauthorized access to your computer with centralized password management with Password Bank, easy
music player launching with Acer MusicLaunch, secure Internet favorites via Acer MyLaunch, and fast
application/website launching and login with Acer FingerLaunch, while Acer ProfileLaunch can launch up to
three applications/websites from a single finger swipe.
Acer Bio-Protection Fingerprint Solution also allows you to navigate through web browsers and documents
using Acer FingerNav. With Acer Bio-Protection Fingerprint Solution, you can now enjoy an extra layer of
protection for your personal computer, as well as the convenience of accessing your daily tasks with a simple
swipe of your finger!
For more information refer to the Acer Bio-Protection help files.
Acer GridVista (dual-display compatible)
NOTE: This feature is only available on certain models.
To enable the dual monitor feature of the notebook, first ensure that the second monitor is connected, then
select Start, Control Panel, Display and click on Settings. Select the secondary monitor (2) icon in the
display box and then click the check box Extend my windows desktop onto this monitor. Finally, click
Apply to confirm the new settings and click OK to complete the process.
Acer GridVista is a handy utility that offers four pre-defined display settings so you can view multiple windows
on the same screen. To access this function, please go to Start´ All Programs and click on Acer GridVista.
You may choose any one of the four display settings indicated below:
16
Chapter 1
Double (vertical), Triple (primary at left), Triple (primary at right), or Quad Acer Gridvista is dual-display
compatible, allowing two displays to be partitioned independently.
Acer Gridvista is dual-display compatible, allowing two displays to be partitioned independently.
AcerGridVista is simple to set up:
1.
2.
3.
Run Acer GridVista and select your preferred screen configuration for each display from the task bar.
Drag and drop each window into the appropriate grid.
Enjoy the convenience of a well-organized desktop.
NOTE: Please ensure that the resolution setting of the second monitor is set to the manufacturer's
recommended value.
Launch Manager
Launch Manager allows you to set the four easy-launch buttons located above the keyboard. You can access
the Launch Manager by clicking on Start > All Programs > Launch Manager to start the application.
Chapter 1
17
Hardware Specifications and Configurations
Processor
Item
Specification
CPU type
Intel® Penryn (dual core)
CPU package
Intel® 479 pin Micro-FCPGA
Features
Supports Intel architecture with Dynamic execution.
On-die, primary 32-kB instruction cache and 32-kB write-back data
cache.
On-die, up to 6MB second level shared cache with advanced
transfer cache architecture.
Streaming SIMD Extensions 2 (SSE2),Streaming SIMD Extensions
3 (SSE3) Supplemental streaming SIMD extensions 3 (SSSE3)
and SSE4.1 instruction sets.
1066MHz source-synchronous front side bus (FSB)
Advanced power management features including Enhanced Intel
SpeedStep® Technology and dynamic FSB frequency switching.
Digital thermal sensor (DTS).
Execute disable bit support for enhanced security.
Intel® Dynamic Acceleration Technology and Enhanced Multi
Threaded Thermal Management (EmTTM).
Support enhanced Intel Virtualization Technology.
CPU core voltage
VCC-CORE: Voltage for the future processor will depend on VID06 for battery mode and setting via software for adapter mode for
the future processor
North Bridge
Item
Specification
Type
Intel Crestline PM965 (North Bridge)
Package
FCBGA 1329 balls
Features
Processor host bus supports, 667/800/1066MHz FSB support.
Supports Dual Channel DDR2 SDRAM at 667/800 MHz.
Supports Dual Channel DDR3 SDRAM at 800/1066 MHz.
Integrated SDRAM controller up to 8GB (2 SODIMM support)
External Graphics interface for PCI Express Architecture support
DMI x2 and DMI x 4 for connection between GMCH and ICH9M
Supports ACPI 3.0
CPU core voltage
1.05V core, 1.5V,VCCSM(DDR2 = 1.8V/DDR3=1.5V),2.5V,3.3V
South Bridge
Item
18
Specification
Type
ICH9M (South Bridge)
Package
BGA 676 balls
Chapter 1
Item
Specification
Features
Upstream accelerated Hub architecture interface for access to
GMCH.
PCI Express Base Specification, Revision 1.1 support.
PCI 2.3 interface. (4 PCI Request/Grant pairs).
ACPI Power Management Logic Support.
Enhanced DMA controller, interrupt controller, timers functions.
Integrated Serial ATA host controllers with independent DMA
operation on six ports and AHCI support.
USB 1.1 & USB 2.0 Host controllers.
Supports Intel High Definition Audio (Intel HD Audio) Interface.
Supports Intel® Matrix Storage Technology.
Supports Intel® Active Management Technology.
Low Pin Count (LPC) interface.
6 PCIe ports.
CPU core voltage
1.05V core,1.5V,3.3V,5V CMOS I/O
CPU Fan True Value Table
CPU Temp (°C)
Fan Speed (rpm)
45
0
50
3000 ± 100
65
3400 ± 100
78
3800 ± 100
90
4200 ± 100
System Clock
Item
Specification
System clock chip
ICS9LPRS365BGLFT or pin compatible device
Package
64 pin TSSOP
Clock Synthesizer
200/166Mhz for CPU, GMCH
100MHz clock buffer for GMCH, ICH8M and PCI-E device, SATA,
Docking station
96MHz GMCH
48Mhz for USB clock inside ICH8M
33Mhz PCI clock for PCI device, LPC
14.31818Mhz for ICH8M
Power
3.3V
Features
Support spread spectrum function, for reducing EMI
Support SM bus interface.
Crystal and Oscillator
Item
Features
Chapter 1
Specification
14.31818Mhz crystal for clock chip
32.768Khz crystal for RTC inside ICH8M and WINBOND
WPC8769LDG
24.576Mhz for RICOH R5C833
25MHZ crystal for BROADCOM Lan controller BCM5787.
19
System Memory
Item
Specification
Memory controller
Built-in
Memory size
0MB (no on-board memory)
DIMM socket number
2 sockets
Supports memory size per socket
2 GB
Supports maximum memory size
4G for 64bit OS (with two 2GB SODIMM)
Supports DIMM type
DDR II 677 Mhz /DDR III 1066 MHz SDRAM memory interface
design
Supports DIMM Speed
667/1066 MHz
Memory module combinations
You can install memory modules in any combinations as long as
they match the above specifications.
Memory Combinations
Slot 1
0MB
Slot 2
256MB
Total Memory
256MB
0MB
512MB
512MB
0MB
1024MB
1024MB
0MB
2048MB
2048MB
256MB
256MB
512MB
256MB
512MB
768MB
256MB
1024MB
1280MB
256MB
2048MB
2304MB
512MB
256MB
768MB
512MB
512MB
1024MB
512MB
1024MB
1536MB
512MB
2048MB
2560MB
1024MB
0MB
1024MB
1024MB
256MB
1280MB
1024MB
512MB
1536MB
1024MB
1024MB
2048MB
1024MB
2048MB
3072MB
2048MB
0MB
2048MB
2048MB
256MB
2304MB
2048MB
512MB
2560MB
2048MB
1024MB
3072MB
2048MB
2048MB
4096MB
Hard Disk Drive Interface
Item
Vendor &
Model
Name
Capacity
(MB)
Bytes per
sector
20
Chapter 1
Item
Data heads
Drive Format
Disks
Spindle
speed
(RPM)
Performance Specifications
Buffer size
Interface
Max. media
transfer
rate (diskbuffer,
Mbytes/s)
Data
transfer
rate
(host~buffe
r, Mbytes/s)
DC Power Requirements
Voltage
tolerance
Combo Drive Module
Item
Specification
Vendor & model name
Performance Specification
Transfer rate (KB/sec)
Buffer Memory
Interface
Applicable disc format
Loading mechanism
Power Requirement
Input Voltage
Thermal Sensor Control
Item
Thermal Sensor Chip
Specification
GMT-780 / LM95245
Package
8-pin MSOP
Features
Thermal sensor control Interface
Interface
I2C bus, address: 98h
BIOS
Item
BIOS vendor
Specification
Phoenix BIOS code
BIOS Version
BIOS ROM type
Serial Flash Memory
BIOS ROM size
1MB
Chapter 1
21
Item
BIOS package
Specification
8 pins SOIC
Supported protocols
BIOS password control
Set by setup manual
LCD 15.4”
Item
Specification
Vendor/model name
Screen Diagonal (mm)
15.4 TFT WXGA, 220nits, 8ms
Active Area (mm)
Display resolution (pixels)
Pixel Pitch
Pixel Arrangement
Display Mode
Typical White Luminance (cd/m2)
also called Brightness
Luminance Uniformity
Contrast Ratio
Response Time (Optical Rise
Time/Fall Time) msec
Nominal Input Voltage VDD
Typical Power Consumption (watt)
Weight (without inverter)
Physical Size (mm)
Electrical Interface
Support Color
Viewing Angle (degree)
Horizontal: Right/Left
Vertical: Upper/Lower
Temperature Range (°C)
Operating
Storage (shipping)
VGA Subsystem
Item
22
Specification
Chipset
Nvidia NB9P-GS with 512M VRAM or NB9M-GS with 256M
VRAM
Package
MXM
Chapter 1
Item
Specification
Features
Unified Shader Architecture
Support Microsoft® DirectX® 10 Shader Model 4
Geometry Instancing 2.0
SGI OpenGL® 2.0 Optimizations and support
Adaptive PCI Express Interface
High efficiency integrated adaptable and programmable
Video Processor (VP2)
Integrated Bit Stream Processor (BSP)
NVIDIA PureVideo/Pure Video HD Technology
Industry Video codec standard hardware acceleration
Advanced Spatial Temporal De-Interlacing
Vibrant Color Temperature Correction
LCD Overdrive
High-Quality Real-Time Video Recording
Best quality 10-bit display pipeline
NVIDIA nView Multi Display Technology
SmartDimmer Technology
Integrated HDMI Support
Support for integrated HDCPNVIDIA Digital Vibrance Control
Technology
Integrate HDTV Encoder
Dual 400MHz RAMDACs
Power
1.0V core,1.2V, 3.3V, 2.5V, 1.8V
KBC
Item
Specification
Chipset
WINBOND WPCE775CA0DG
Features
Host interface, base on Intel's LPC Interface specification
Revision 1.0
PC01 REV 1.0 and ACPI 3.0 compliant
Supports Microsoft® Advanced Power Management (APM)
Specifications Rev 1.2
Share BIOS flash memory5.Support for SPI flash memories
Host-controlled CIR Port
High-accuracy, high-speed ADC
Up to 84 GPIO ports (including keyboard scanning) with a
variety of wake-up events.
16-bit RISC core, with up to 4 Mbytes of external address
space, and running at up to 25 MHZ
128 pin LQFP package
Chapter 1
23
Memory Card Reader
Item
Specification
Type
JMicron JMB385
Features
Support 5-in-1 Card Reader (MS,MS pro, SD, MMC, xD)
Compliant with SD Memory Card Specification Version 2.0
Compliant with MultiMediaCard Specification Version 4.1
Compliant with Memory Stick Standard Format Specification
Version 1.4
Compliant with Memory Stick PRO Format Specification
Version 1.00
Compliant with xD Picture Card Specification Version 1.20
Compliant with xD Picture Card Host Guideline Version 1.20
CIR
Item
Specification
Type
EVERLIGHT BEBK0075Z00
Features
Low voltage and low power consumption.
Suitable burst length 10 pulses/burst.
Audio Interface
Item
Specification
Audio Controller
Realtek ALC888 Azadia Codec and Amplifier GMT G1412
+ G1411
Features
HD Audio
97dB SNR DACs & 90dB SNR ADCs
Ten DAC channels support 16/20/24-bit PCM format for 7.1
sound playback, plus 2 channels of independent stereo
sound output (multiple streaming) through the front panel
output
Two stereo ADCs support 16/20/24-bit PCM format, one
for stereo microphone, one for legacy mixer recording
All DACs supports 44.1k/48k/96k/192kHz sample rate
All ADCs support 44.1k/48k/96k sample rate
Two independent 16/20/24-bit S/PDIF-OUT converters
support 44.1k/48k/96k/192kHz sample rate, one for
nominal digital audio, the other one for digital audio output
to HDMI transmitter
Enable VoIP function
Subwoofer support
LAN Interface
Item
24
Specification
LAN Chipset
Broadcom 5764M
Features
Integrated 10/100/1000 BASE -T transceiver
PCIe V1.1 compliant
Wake on LAN support meeting the ACPI requirements
68pin-QFN package
Chapter 1
Bluetooth Interface
Item
Specification
Chipset
FOXCON T60H928.11 Bluetooth miniUSB module
Features
Internal Mini USB solution with antenna
Bluetooth 2.0+EDR
Bluetooth control for BT optical mouse
Keyboard
Item
Specification
Type
Aspire series: New Acer Non-Ergo Keyboard
Total number of keypads
88-/89-/93-key
Windows logo key
Yes
Internal & external keyboard work
simultaneously
Plug USB keyboard to the USB port directly: Yes
MDC Card
Item
Specification
Chipset
Intel® Wireless WiFi Link 5100/5300
Features
•
ITU-T V.92, V.90 Data Mode with auto-fallback to, V.34,
V.32terbo, and V.32bis.
•
V.42 LAPM and MNP 2-4 error correction.
•
V.44, V.42bis and MNP 5 data compression.
•
Send and receive rates up to 14400bps, support ITU-T
V.17, V.29, V.27ter, and V.21 Ch2 fax.
•
TIA/EIA 602 Standard for AT command set, and Fax
TIA/EIA 578 Class 1 command set.
•
DTMF and call progress monitor.
Camera
Item
Type
Specification
0.3M pixel camera module
Finger Print Board
Item
Features
Specification
TruePrint® and TrueMatch® Technology.
TrueNav® Cursor and Menu Navigation Technology
High Definition 128 x 8 Pixel Array
Multiple battery-friendly operating modes @ 3.3V
Built-in low power Finger Detection w/ remote wakeup
capability
USB 2.0 Full Speed Interface
Battery
Item
Vendor & model name
Specification
SANYO/Sony/ SIMPLO/
PANASONIC
Battery Type
Li-ion
Pack capacity
4000/4800 mAh
Number of battery cell
6/8
Package configuration
3S2P/4S2Pl
Chapter 1
25
Item
26
Specification
Normal voltage
11.1V
Charge voltage
16.0V
Chapter 1
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if
you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press F2 during POST (when “Press <F2> to enter Setup” message is prompted
on the bottom of screen).
Press F2 to enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change
boot device without entering BIOS Setup Utility, please set the parameter to “enabled”.
Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without
entering BIOS SETUP Utility.
Navigating the BIOS Utility
There are six menu options: Information, Main, Advanced, Security, Boot, and Exit.
Follow these instructions:
•
To choose a menu, use the left and right arrow keys.
•
To choose an item, use the up and down arrow keys.
•
To change the value of a parameter, press F5 or F6.
•
A plus sign (+) indicates the item has sub-items. Press Enter to expand this item.
•
Press Esc while you are in any of the menu options to go to the Exit menu.
In any menu, you can load default settings by pressing F9. You can also press F10 to save any
changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values. Please
note that system information is subject to different models.
•
Chapter 2
27
Information
The Information screen displays a summary of your computer hardware information.
Information
Main
InsydeH20 Setup Utility
Advanced
Security
Power
Rev. 3.5
Boot
Exit
CPU Type:
CPU Speed:
Intel (R) Core (TM)2 Duo CPU @ 2.40GHz
2.40GHz
HDD Model Name:
HDD Serial Number:
ATAPI Model Name:
Hitachi HTS543516K9SA00
071129BB0C02WGHDKKGC
Slimtype DVD A DS8A2S
System BIOS Version:
VGA BIOS Version:
Serial Number:
Asset Tag Number:
Product Name:
Manufacturer Name:
UUID:
V0.15T2
Intel V1588
F1 Help
ESC Exit
Aspire 4930
Acer
864BD4BE-6B22-5843-38D2-001B38D637FC
↑↓ Select Item
←→ Select Menu
F5/F6 Change Item
F9 Setup Default
Enter SelectXSubmenu F10 Save and Exit
NOTE: The system information is subject to different models.
Parameter
28
Description
CPU Type
This field shows the CPU type and speed of the system.
CPU Speed
This field shows the speed of the CPU.
HDD Model Name
This field shows the model name of HDD installed on primary IDE master.
HDD Serial Number
This field displays the serial number of HDD installed on primary IDE master.
ATAPI Model Name
This field shows the model name of the Optical device installed in the system.
System BIOS Version
Displays system BIOS version.
VGA BIOS Version
This field displays the VGA firmware version of the system.
Serial Number
This field displays the serial number of this unit.
Asset Tag Number
This field displays the asset tag number of the system.
Product Name
This field shows product name of the system.
Manufacturer Name
This field displays the manufacturer of this system.
UUID Number
Universally Unique Identifier (UUID) is an identifier standard used in software
construction, standardized by the Open Software Foundation (OSF) as part of
the Distributed Computing Environment (DCE).
Chapter 2
Main
The Main screen allows the user to set the system time and date as well as enable and disable boot option
and recovery.
Information
Main
InsydeH20 Setup Utility
Advanced
Security
Power
System Time
System Date
[13:04:04]
[04/21/2008]
Total Memory
Video Memory
3017 MB
[32MB]
Quick Boot
Network Boot
F12 Boot Menu
D2D Recovery
SATA Mode
[Enabled]
[Enabled]
[Disabled]
[Enabled]
[ACHI]
F1 Help
ESC Exit
↑↓ Select Item
←→ Select Menu
Boot
Rev. 3.5
Exit
Item Specific Help
This is the help for the
hour field. Valid range
is from 0 to 23.
INCREASE/REDUCE : F5/F6
F5/F6 Change Item
F9 Setup Default
Enter SelectXSubmenu F10 Save and Exit
NOTE: The screen above is for your reference only. Actual values may differ.
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Format/Option
System Time
Sets the system time. The hours are displayed with 24hour format.
Format: HH:MM:SS
(hour:minute:second)
System Date
Sets the system date.
Format MM/DD/YYYY
(month/day/year)
Total Memory
This field reports the memory size of the system.
Memory size is fixed to 3017 MB.
N/A
Video Memory
Shows the video memory size. VGA Memory size=32 MB
N/A
Quick Boot
Allows startup to skip certain tests while booting,
decreasing the time needed to boot the system.
Option: Enabled or
Disabled
Network Boot
Enables, disables the system boot from LAN (remote
server).
Option: Enabled or
Disabled
F12 Boot Menu
Enables, disables Boot Menu during POST.
Option: Disabled or
Enabled
D2D Recovery
Enables, disables D2D Recovery function. The function
allows the user to create a hidden partition on hard disc
drive to store operation system and restore the system
to factory defaults.
Option: Enabled or
Disabled
SATA Mode
Control the mode in which the SATA controller should
operate.
Option: AHCI Mode or IDE
Mode
NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is
because the user is not allowed to control the settings in these cases.
Chapter 2
29
Advanced
The Advanced screen allows the user to configure the various advanced BIOS options.
IMPORTANT:Making incorrect settings to items on these pages may cause the system to malfunction. Unless
you have experience adjusting these items, we recommend that you leave these settings at the
default values. If making settings to items on these pages causes your system to malfunction or
prevents the system from booting, open BIOS and choose Load Optimal Defaults in the Exit menu to
boot up normally.
Information
InsydeH20 Setup Utility
Advanced
Security
Power
Main
XBoot Configuration
XPeripheral Configuration
XIDE Configuration
XVideo Configuration
XUSB Configuration
XChipset Configuration
XACPI Table/Features Control
Express Card
XPCI Express Root Port 1
XPCI Express Root Port 2
XPCI Express Root Port 3
XPCI Express Root Port 4
XPCI Express Root Port 5
XPCI Express Root Port 6
Rev. 3.5
Boot
Exit
Item Specific Help
Configures Boot
Settings.
[Disabled]
XASF Configuration
F1 Help
ESC Exit
↑↓ Select Item
←→ Select Menu
F5/F6 Change Item
F9 Setup Default
Enter SelectXSubmenu F10 Save and Exit
The table below describes the items, menus, and submenus in this screen. Settings in boldface are the default
and suggested parameter settings.
Parameter
30
Description
Submenu Items
Boot
Configuration
Enter the Boot Configuration menu.
•
•
Numlock
Zip Emulation Type
Peripheral
Configuration
Enter the Peripheral Configuration menu.
•
•
•
•
Serial Port A
Infrared Port
Azalia
LAN
IDE
Configuration
Enter the IDE Configuration menu.
•
•
•
•
•
IDE Controller
HDC Configure as
ACHI Option ROM Support
SATA Port 0, 1, 4, and 5 Hotplug
Channel 1 to 4 Master and Slave
Video
Configuration
Enter the Video Configuration menu.
•
•
•
•
•
•
•
•
IGD Device2, Function1
IGD Pre-allocate Memory
IGD DVMT Size
Clock Chip Intialize
Enabled CK SSC
IGD Boot Type
IGD LCD Panel Type
IGD TV
Chapter 2
Parameter
Description
Submenu Items
USB
Configuration
Enter the USB Configuration menu.
•
•
•
•
USB Driver Select
EHCI 1 and 2
UHCI 1 to 5
Per-Port Control
Chipset
Configuration
Enter the Chipset Configuration menu.
•
•
•
•
Port 80h Cycles
DMI Link ASPM Control
PCI Latency Timer
VT-d
ACPI Table/
Features Control
Enter the ACPI Table/Features Control
menu.
•
•
•
•
•
•
FACP C2 Latency Value
FACP C3 Latency Value
FACP RTC S4 Wakeup
APIC IO APIC Mode
HPET Support
Base Address Select
Express Card
Disable or Enable the Express Card
solution for windows Standby and
Hibernation.
N/A
PCI Express
Root Port 1 to 6
Enter the PCI Port 1 to 6 configuration
menus.
•
•
•
•
•
•
•
•
•
•
•
•
•
VC1 Enable
ASPM
URR
FER
NFER
CER
CTO
SEFE
SENFE
SECE
PME Interrupt
PME SCI
Hot Plug SCI
ASF
Configuration
Enter the ASF Configuration menu.
•
•
•
•
Mini Watchdog Timeout
BIOS Boot Timeout
OS Boot Timeout
Power-on wait time
Chapter 2
31
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized
use.
Information
Main
InsydeH20 Setup Utility
Advanced
Security
Power
Supervisor Password Is:
User Password Is:
HDD Password Is:
Clear
Clear
Clear
Set Supervisor Password
Set User Password
Set Hdd Password
Power on password
[32MB]
F1 Help
ESC Exit
Boot
Rev. 3.5
Exit
Item Specific Help
Install or Change the
password and the length
of password must be less
than eight words.
[Enabled]
↑↓ Select Item
←→ Select Menu
F5/F6 Change Item
F9 Setup Default
Enter SelectXSubmenu F10 Save and Exit
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Option
Supervisor Password Is
Shows the setting of the Supervisor password
Clear or Set
User Password Is
Shows the setting of the user password.
Clear or Set
HDD Password Is
Shows the setting of the hard disk password.
Clear or Set
Set Supervisor Password
Press Enter to set the supervisor password. When
set, this password protects the BIOS Setup Utility
from unauthorized access. The user can not either
enter the Setup menu nor change the value of
parameters.
Set User Password
Press Enter to set the user password. When user
password is set, this password protects the BIOS
Setup Utility from unauthorized access. The user can
enter Setup menu only and does not have right to
change the value of parameters.
Set HDD Password
Enter HDD Password.
Password on Boot
Defines whether a password is required or not while
the events defined in this group happened. The
following sub-options are all requires the Supervisor
password for changes and should be grayed out if the
user password was used to enter setup.
Disabled or
Enabled
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget
your password. If you forget your password, you may have to return your notebook computer to your
dealer to reset it.
32
Chapter 2
Setting a Password
Follow these steps as you set the user or the supervisor password:
1.
Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The
Set Supervisor Password box appears:
2.
Type a password in the “Enter New Password” field. The password length can not exceeds 8
alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New
Password” field.
IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
3.
Press Enter. After setting the password, the computer sets the User Password parameter to “Set”.
4.
If desired, you can opt to enable the Password on boot parameter.
5.
When you are done, press F10 to save the changes and exit the BIOS Setup Utility.
Removing a Password
Follow these steps:
1.
Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The
Set Password box appears:
2.
Type the current password in the Enter Current Password field and press Enter.
3.
Press Enter twice without typing anything in the Enter New Password and Confirm New Password fields.
The computer then sets the Supervisor Password parameter to “Clear”.
4.
When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.
Chapter 2
33
Changing a Password
1.
Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The
Set Password box appears.
2.
Type the current password in the Enter Current Password field and press Enter.
3.
Type a password in the Enter New Password field. Retype the password in the Confirm New Password
field.
4.
Press Enter. After setting the password, the computer sets the User Password parameter to “Set”.
5.
If desired, you can enable the Password on boot parameter.
6.
When you are done, press F10 to save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following.
The password setting is complete after the user presses Enter.
If the current password entered does not match the actual current password, the screen will show you the
Setup Warning.
If the new password and confirm new password strings do not match, the screen will display the following
message.
34
Chapter 2
Power
The Power screen allows the user to configure various CPU and power management options and device
wakeup behavior.
Information
InsydeH20 Setup Utility
Advanced
Security
Power
Main
Boot
XAdvanced CPU Control
XPlatform Power Management
ACPI S3:
Wake on PME
Wake on Modem Ring
Auto wake on S5
Quickly S4 Resume
F1 Help
ESC Exit
↑↓ Select Item
←→ Select Menu
Rev. 3.5
Exit
Item Specific Help
These items control
various CPU parameters.
[Enabled]
[Enabled]
[Enabled]
[Disabled]
[Disabled]
F5/F6 Change Item
F9 Setup Default
Enter SelectXSubmenu F10 Save and Exit
The table below describes the items, menus, and submenus in this screen. Settings in boldface are the default
and suggested parameter settings.
Parameter
Advanced CPU
Control
Chapter 2
Description
Enter the Advanced CPU Control menu.
Submenu Items
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
P-States (IST)
Boot performance mode
Thermal Mode
CMP Support
Use XD capability
VT Support
C-States
Enhanced C-States
C-State Pop Up Mode
C-State Pop Down Mode
C4 Exit Timing Mode
DeepC4
Hard C4E
Enable C6
EMTTM
Bi-directional PROCHOT#
Dynamic FSB Switching
Turbo Mode
ACPI 3.0 T-States
DTS
DTS Calibration
Thermal Trip Points Setting (Fan
On Temp., Throttle On Temp.)
35
Parameter
36
Description
Submenu Items
Platform Power
management
Enter the Platform Power Management
menu.
•
•
•
PCI Clock Run
_CST - C4 Latency Value
C4 on C3 - Deeper Sleep
ACPI S3
Enable or Disable ACPI S1/S3 Sleep State
N/A
Wake on PME
Enable or Disable wake up when the
system power is off and a PCI Power
Management Enable wake up event occurs.
N/A
Wake on Modem
Ring
Enable or Disable wake up when the
system power is off and a modem attached
to the serial port is ringing.
N/A
Auto wake on S5
Disable or Enable auto wake up by date
and time or at a fixed time everyday.
N/A
Quickly S4
Resume
Disable or Enable optional quick boot from
S4 Resume.
N/A
Chapter 2
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices
includes the USB diskette drives, the onboard hard disk drive and the DVD drive in the module bay.
Information
Main
InsydeH20 Setup Utility
Advanced
Security
Power
Boot priority order:
1. IDE0 : Hitachi HTS542516K9SA00
2. IDE1 : Slimtype DVD A DS8A2S
3 . USB FDD :
4. Network Boot : Realtek Boot Agent
5. USB HDD :
6. USB CDROM :
F1 Help
ESC Exit
Chapter 2
↑↓ Select Item
←→ Select Menu
Boot
Rev. 3.5
Exit
Item Specific Help
Use <↑> or <↓> to select
a device, then press
<F5> to move it down the
list, or <F6> to move
it up the list. Press
<Esc> to escape the menu
F5/F6 Change Item
F9 Setup Default
Enter SelectXSubmenu F10 Save and Exit
37
Exit
The Exit screen allows you to save or discard any changes you made and quit the BIOS Utility.
Information
Main
InsydeH20 Setup Utility
Advanced
Security
Power
Boot
Exit Saving Changes
Exit Discarding Changes
Load Setup Defaults
Discard Changes
Save Changes
F1 Help
ESC Exit
↑↓ Select Item
←→ Select Menu
Rev. 3.5
Exit
Item Specific Help
Exit System Setup and
save your changes to
CMOS.
F5/F6 Change Item
F9 Setup Default
Enter SelectXSubmenu F10 Save and Exit
The table below describes the parameters in this screen.
Parameter
38
Description
Exit Saving Changes
Exit System Setup and save your changes to CMOS.
Exit Discarding
Changes
Exit utility without saving setup data to CMOS.
Load Setup Default
Load default values for all SETUP item.
Discard Changes
Load previous values from CMOS for all SETUP items.
Save Changes
Save Setup Data to CMOS.
Chapter 2
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
•
New versions of system programs
•
New features or options
•
Restore a BIOS when it becomes corrupted.
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not
completely loaded.
Fellow the steps below to run the Phlash.
1.
Prepare a bootable diskette.
2.
Copy the flash utilities to the bootable diskette.
3.
Then boot the system from the bootable diskette. The flash utility has auto-execution function.
Chapter 2
39
Remove HDD/BIOS Utility
This section provide you with removing HDD/BIOS method:
Remove HDD Password:
•
If you key in wrong HDD password three times, HDD password error code displays. See the image
below.
To reset the HDD password, run HDD_PW.EXE as follows:
1. Key in hdd_pw 15494 0
2. Press 2.
3. Select one upper-case string from the list.
4. Reboot system and key in the selected string (0KJFN42 or UVEIQ96) on the HDD User
Password screen.
40
Chapter 2
Remove BIOS Password:
If you key in the wrong Supervisor Password three times, System Disabled displays on the screen. See the
image below.
To reset the BIOS password, run BIOS_PW.EXE as follows:
1. Key in bios_pw 14452 0
2. Select one string from the list.
Chapter 2
41
3. Reboot the system and key in the selected string (qjjg9vy, 07yqmjd etc.) for the BIOS user
password.
42
Chapter 2
Chapter 3
Machine Disassembly and Replacement
This chapter contains step-by-step procedures on how to disassemble the notebook computer for
maintenance and troubleshooting.
Disassembly Requirements
To disassemble the computer, you need the following tools:
•
Wrist grounding strap and conductive mat for preventing electrostatic discharge
•
Flat screwdriver
•
Philips screwdriver
•
Hex screwdriver
•
Plastic flat screwdriver
•
Plastic tweezers
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
Chapter 3
43
General Information
Pre-disassembly Instructions
Before proceeding with the disassembly procedure, make sure that you do the following:
1. Turn off the power to the system and all peripherals.
2. Unplug the AC adapter and all power and signal cables from the system.
3. Place the system on a flat, stable surface.
4. Remove the battery pack.
Disassembly Process
The disassembly process is divided into the following stages:
•
•
•
External module disassembly
Main unit disassembly
LCD module disassembly
The flowcharts provided in the succeeding disassembly sections illustrate the entire disassembly sequence.
Observe the order of the sequence to avoid damage to any of the hardware components. For example, if you
want to remove the main board, you must first remove the keyboard, then disassemble the inside assembly
frame in that order.
Main Screw List
Screw
44
Quantity
Part Number
M2.5*8 (NL)
15
MA000005YG0
M2.5*5 (NL)
22
MA000007YG0
M2.5*3 (NL)
2
MA000005WG0
M2*3 (NL)
36
MA0000060G0
M2.5*4 (NL)
2
MA0000005G0
M2*6 (NL)
4
MMCK20060G0
M2*4-NI (NL)
5
MACK20040G0
M3*3 (NL)
4
MAAA03032G0
M2*6.5
4
MA0000096G0
M2.5*5.0
2
MA000002NG0
M2.5*6.5
4
MA000006C00
Chapter 3
External Module Disassembly Process
External Modules Disassembly Flowchart
The flowchart below gives you a graphic representation on the entire disassembly sequence and instructs you
on the components that need to be removed during servicing. For example, if you want to remove the main
board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.
Screw List
Step
Screw
Quantity
Color
Part No.
Memory Cover
M2.5*8 (NL)
4
Black
MA000005YG0
HDD Cover
M2*6 (NL)
2
Black
MMCK20060G0
WLAN Cover
M2.5*8 (NL)
4
Black
MA000005YG0
WLAN Module
M2*3 (NL)
2
Black
MA0000060G0
HDD Carrier
M3*3 (NL)
4
Silver
MAAA03032G0
ODD Module
M2.5*5(NL)
1
Black
MA000002NG0
ODD Bracket
M2*3 (NL)
3
Black
MA0000060G0
Chapter 3
45
Removing the Battery Pack
1. Turn computer over.
2. Slide the battery lock/unlock latch to the unlock position.
3. Slide and hold the battery release latch to the release position (1), then slide out the battery pack from the main
unit (2).
2
1
46
Chapter 3
Removing the SD dummy card
1. Push the SD dummy card all the way in to eject it.
2. Pull it out from the slot.
Chapter 3
47
Removing the ExpressCard dummy card
1. Push the ExpressCard dummy card all the way in to eject it.
2. Pull it out from the slot.
48
Chapter 3
Removing the Lower Covers
1. See “Removing the Battery Pack” on page 46.
2. See “Removing the Lower Covers” on page 49.
3. See “Removing the Lower Covers” on page 49.
4. Loosen the ten captive screws from the Memory, HDD1, and HDD2 Covers.
Memory
Cover
HDD1
Cover
HDD2
Cover
5. Carefully open the memory cover.
6. Remove the HDD1 cover as shown.
Chapter 3
49
7. Remove the HDD2 cover as shown.
Removing the DIMM Modules
1. See “Removing the Battery Pack” on page 46.
2. Remove the Memory Module cover. See “Removing the Lower Covers” on page 49.
3. Push out the release latches on both sides of the DIMM socket to release the DIMM module.
4. Remove the DIMM module.
5. Repeat steps for the second DIMM module.
50
Chapter 3
Removing the MXM Module
1. See “Removing the Battery Pack” on page 46.
2. Remove the Memory Module cover. See “Removing the Lower Covers” on page 49.
3. Remove the four securing screws.
Step
WLAN Module
Size
M2.5*9 (NL)
Quantity
Screw Type
4
4. Grasp the module and remove.
Removing the Turbo RAM module
1. See “Removing the Battery Pack” on page 46.
2. Remove the HDD2 cover. See “Removing the Lower Covers” on page 49.
Chapter 3
51
3. Remove the three securing screws.
Step
WLAN Module
Size
M2*3 (NL)
Quantity
Screw Type
3
4. Remove the bracket from the module.
5. Remove the Turbo RAM Module.
NOTE: Some models come equipped with either a TV Tuner module or a Turbo RAM module.
52
Chapter 3
Removing the TV Tuner module
1. See “Removing the Battery Pack” on page 46.
2. Remove the HDD2 cover. See “Removing the Lower Covers” on page 49.
3. Disconnect the TV Tuner cable from the module.
4. Remove the three securing screws.
Step
TV Tuner Module
Chapter 3
Size
M2*3 (NL)
Quantity
Screw Type
3
53
5. Remove the bracket from the module.
6. Remove the TV Tuner module.
NOTE: Some models come equipped with either a TV Tuner module or a Turbo RAM module.
Removing the WLAN Module
1. See “Removing the Battery Pack” on page 46.
2. Remove the HDD2 cover. See “Removing the Lower Covers” on page 49.
3. Remove the Turbo RAM. See “Removing the TV Tuner module” on page 53.
4. Disconnect the antenna cables from the WLAN board.
54
Chapter 3
NOTE: The following is the correct cable-color to connector designation: TR1 (left) to White, TR3 (middle) to
Gray, and TR2 (right) to Black.
5. Move the cables away to avoid damaging the them, and remove the two screws on the WLAN board to release
the WLAN board.
Step
WLAN Module
Size
M2*3 (NL)
Quantity
Screw Type
2
6. Detach the WLAN board from the WLAN socket.
Removing the Hard Disk Drive1 Module
1. Remove the Battery Pack. See “Removing the Battery Pack” on page 46.
2. Remove the HDD1 cover. See “Removing the Lower Covers” on page 49.
Chapter 3
55
3. Remove the two securing screws.
Step
HDD Carrier
Size
M2*3 (NL)
Quantity
Screw Type
2
4. Use the pull-tab to lift up the HDD1 module to remove.
NOTE: To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it.
56
Chapter 3
5. Remove the four screws (two each side) securing the HDD to the carrier.
Step
HDD Carrier
Size
M2*3 (NL)
Quantity
Screw Type
4
6. Turn the HDD module upside down, and lift the HDD carrier up.
Chapter 3
57
Removing the Hard Disk Drive2 Module
1. See “Removing the Battery Pack” on page 46.
2. Remove the HDD2 cover. See “Removing the Lower Covers” on page 49.
3. Remove the two securing screws.
Step
HDD Carrier
Size
M2*3 (NL)
Quantity
Screw Type
2
4. Use the pull-tab to lift up the HDD module and remove.
NOTE: To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it.
58
Chapter 3
5. Remove the four screws (two each side) securing the HDD to the carrier.
Step
HDD Carrier
Size
M2*3 (NL)
Quantity
Screw Type
4
6. Turn the HDD module upside down, and lift the HDD carrier up.
7. Remove the connector from the HDD.
Chapter 3
59
Removing the Optical Drive Module
1. See “Removing the Battery Pack” on page 46.
2. Remove the Memory cover. See “Removing the Lower Covers” on page 49.
3. Loosen the captive screw securing the ODD module and remove the ODD cap.
4. Carefully use a screwdriver to push the locking catch and remove the ODD module.
5. Grasp the module and pull out from the main unit.
60
Chapter 3
6. Remove the two screws securing the ODD bracket and remove the ODD bracket from the optical disk drive
module.
Step
ODD Bracket
Size
M2*2.5(NL)
Quantity
Screw Type
2
7. Insert a pin in the eject hole of the ODD to eject the ODD tray.
8. Press down on the locking catch to release the ODD cover and remove.
Chapter 3
61
Main Unit Disassembly Process
Main Unit Disassembly Flowchart
Screw List
Step
62
Screw
Quantity
Color
Part No.
Switch Cover
M2*3 (NL)
2
MA0000060G0
LCD Module
M2.5*8(NL)
4
MA000005YG0
LCD Module
M2.5*5 (NL)
2
MA000007YG0
Upper Cover
M2.5*8 (NL)
8
MA000005YG0
Upper Cover
M2.5*5 (NL)
7
MA000007YG0
Touch Pad Bracket
M2*3 (NL)
2
MA0000060G0
Launch Board
M2*3 (NL)
2
MA0000060G0
Speaker
M2*3 (NL)
4
MA0000060G0
I/O Board
M2.5*5 (NL)
1
MA000007YG0
Bluetooth Board
M2*3 (NL)
1
MA0000060G0
Modem Module
M2*3 (NL)
2
MA0000060G0
Mainboard
M2.5*5 (NL)
1
MA000007YG0
Thermal Module
M2*6.5
4
MA0000096G0
CPU Fan
M2*4-NI (NL)
3
MACK20040G0
HDMI Module
M2*4-NI (NL)
2
MACK20040G0
Chapter 3
Removing the Switch Cover
CAUTION: Using tools to remove the Switch Cover may cause damage to the outer casing. It is
recommended that only fingers are used to remove the Switch Cover.
1. Remove the Battery Pack. See “Removing the Battery Pack” on page 46.
2. Locate and remove the nine securing screws as shown.
Step
Size
Quantity
Switch Cover
M2.5*3(NL)
Blue Callout
4
Switch Cover
M2.5*6.5(NL)
Red Callout
5
Screw Type
3. Turn the computer over and open the LCD module fully to expose the Switch Cover.
4. Lift the Switch Cover up and away.
Chapter 3
63
Removing the Switch Board
1. Remove the Switch Cover. See “Removing the Switch Cover” on page 63.
2. Remove the two securing screws from the Switch Board.
Step
Switch Board
Size
M2*3 (NL)
Quantity
Screw Type
2
3. Disconnect the Switch Board to Ekey board FFC cable as shown.
4. Use the tweezers to secure the cable in place, then remove the Switch Board away from the top cover.
64
Chapter 3
Removing the Keyboard
1. Remove the Switch Cover. See “Removing the Switch Cover” on page 63.
2. Grasp the keyboard and lift up to remove.
3. Lift the keyboard over and disconnect the keyboard FFC.
4. Remove the keyboard and place it on a clean surface.
Removing the Modem Module
1. Remove the Keyboard. See “Removing the Keyboard” on page 65.
Chapter 3
65
2. Remove the two securing screws.
Step
Modem Module
Size
M2*3 (NL)
Quantity
Screw Type
2
3. Using a plastic pry, partially lift up the module to expose the connector.
4. While holding the module, use the plastic tweezers to hold the connector and pull the module away to remove.
66
Chapter 3
Removing the Antenna, MIC and Speaker Cables
IMPORTANT:Ensure the Antenna Cables are free of any obstructions before attempting to remove.
1. Remove the WLAN Module. See “Removing the WLAN Module” on page 54.
2. Remove the HDD2 Module. See “Removing the Hard Disk Drive2 Module” on page 58.
3. Remove the MXM Module. See “Removing the MXM Module” on page 51.
4. Remove the Keyboard. See “Removing the Keyboard” on page 65.
5. Gently pull the Antenna Cables through the HDD housing.
6. Disconnect the MIC and speaker cables.
IMPORTANT:Use tweezers to remove the cable connectors. Do not pull on the cable itself to prevent stripping.
Chapter 3
67
7. Gently pull the MIC and Speaker cables through the HDD housing.
8. Turn the computer on its side, and feed cables through to the upperside.
9. Pull the cables completely through.
Remove Keyboard
from this image.
68
Chapter 3
Removing the LCD Module
1. Remove the Battery Pack. See “Removing the Battery Pack” on page 46.
2. Remove the SD dummy card. See “Removing the Lower Covers” on page 49.
3. Remove the Express dummy card. See “Removing the Lower Covers” on page 49.
4. Remove the Lower Covers. See “Removing the Lower Covers” on page 49.
5. Remove the DIMM Modules. See “Removing the DIMM Modules” on page 50.
6. Remove the WLAN Module. See “Removing the WLAN Module” on page 54.
7. Remove the HDDs. See “Removing the Hard Disk Drive1 Module” on page 55. See “Removing the Hard Disk
Drive2 Module” on page 58.
8. Remove the ODD. See “Removing the Optical Drive Module” on page 60.
9. Remove the Modem Module. See “Removing the Modem Module” on page 65.
10. Disconnect the Antenna, MIC and Speaker cables. See “Removing the Antenna, MIC and Speaker Cables” on
page 67.
11. Remove the two securing screws from the bottom of the chassis.
Step
LCD Module
Size
M2.5*6.5(NL)
Quantity
Screw Type
2
12. Turn the computer over. Use the tweezers to disconnect the LCD interface cable from the chassis.
Chapter 3
69
13. Remove the single ground screw and four securing screws (two each side) connecting the LCD module.
Step
Size
Quantity
LCD Module
M2.5*6.5 (NL)
Red Callout
4
Ground
M2.5*3 (NL)
Blue Callout
1
Screw Type
14. Carefully remove the LCD module from the chassis.
70
Chapter 3
Removing the Upper Cover
1. See “Removing the LCD Module” on page 69.
2. Place the computer upside down and remove the remaining eleven screws on the bottom panel.
Step
LCD Module
Size
M2.5*6.5(NL)
Quantity
Screw Type
11
3. Turn the computer over and loosen the captive screw from the keyboard plate.
4. Remove the keyboard plate. If necessary, use a plastic pry to lift the plate.
Chapter 3
71
5. Disconnect the five cables from the mainboard as shown.
A
B
E
C
D
IMPORTANT:When removing cables, always hold the cable by the pull-tab or by the connector. Do not hold
the pull by the cable itself to prevent stripping.
72
Disconnect A as shown.
Release the securing latches and disconnect B as
shown.
Release the securing latches and disconnect C as
shown.
Release the securing latches and disconnect D as
shown.
Chapter 3
Release the securing latches and disconnect E as shown.
6. Remove the four securing screws from the upper cover.
7. Grasp the Upper Cover by the hinge socket and pry it open. Do not lift the cover completely off.
NOTE: Do not try to pry open more than one edge at a time.
8. While holding the cover open, pull through any remaining cables.
Chapter 3
73
9. Grasp the cover by the opposite edge and lift up to remove the Upper Cover.
74
Chapter 3
Removing the Touch Pad
1. Remove the Upper Cover. See “Removing the Upper Cover” on page 71.
2. Remove the Speaker Module. See “Removing the Speaker Module” on page 79.
3. Remove the Finger Print Reader Module. See “Removing the Finger Print Reader” on page 76.
4. Remove the Launch Board Module. See “Removing the Launch Board” on page 77.
5. Remove the Launch Board Module. See “Removing the Launch Board” on page 77.
6. Disconnect the Touch Pad cable from the Touch Pad board.
IMPORTANT:The Touch Pad cannot be removed individually. To replace the Touch Pad, replace the entire
Upper Cover.
Chapter 3
75
Removing the Finger Print Reader
1. Remove the Upper Cover. See “Removing the Upper Cover” on page 71.
2. Disconnect the cable as shown.
3. Disconnect the two FFC cables as shown.
4. Remove the four securing screw from the Finger Print Reader board.
Step
Launch Board
76
Size
M2*3 (NL)
Quantity
Screw Type
4
Chapter 3
5. Remove the bracket from the board.
6. Remove the Finger Print Reader board from the Upper Cover.
Removing the Launch Board
1. Remove the Upper Cover. See “Removing the Upper Cover” on page 71.
2. Lift up the locking latch and remove the FFC cable as shown.
3. Remove the four screws from the Launch Board.
Chapter 3
77
Step
Launch Board
Size
M2*3 (NL)
Quantity
Screw Type
4
4. Remove the Launch Board from the Upper Cover.
78
Chapter 3
Removing the Speaker Module
1. Remove the Upper Cover. See “Removing the Upper Cover” on page 71.
2. Remove four securing screws connecting the Speaker Module.
Step
Speaker Module
Size
M2*6 (NL)
Quantity
Screw Type
4
3. Remove the Speaker Module from the upper cover.
Removing the eKey Module
1. Remove the Upper Cover. See “Removing the Upper Cover” on page 71.
2. Turn the Upper Cover upside down and remove the two securing screws connecting the eKey module.
3. Disconnect the eKey Module cable.
Chapter 3
79
Step
Speaker
Size
M2*3 (NL)
Quantity
Screw Type
2
4. Remove the module as shown.
80
Chapter 3
Removing the Bluetooth board
1. Remove the Upper Cover. See “Removing the Upper Cover” on page 71.
2. Remove the securing screw from the Bluetooth board.
Step
Bluetooth Board
Size
M2*3 (NL)
Quantity
Screw Type
1
3. Lift the Bluetooth board away from the main board and disconnect the mainboard cable.
4. Disconnect the cable from the mainboard.
Chapter 3
81
Removing the Subwoofer Module
1. See “Removing the Upper Cover” on page 71.
2. Remove the four securing screws from the Subwoofer Module.
Step
Subwoofer
Module
Size
M2.5*4 (NL)
Quantity
Screw Type
4
3. Grasp the cable by the end and guide it out of its housing as shown in the following images.
IMPORTANT:The housing guides are hooked to hold the cable in place. Do not pull the cable to remove it or
damage can occur.
82
Chapter 3
4. Grasp the Subwoofer Module and lift it up to remove.
Removing the ExpressCard Module
1. See “Removing the Upper Cover” on page 71.
2. Remove the two securing screws.
IMPORTANT:Do not grasp the cable itself to prevent fraying.
Step
Modem Module
Size
M2*3 (NL)
Quantity
Screw Type
2
3. Disconnect the cable connecting the ExpressCard module.
Chapter 3
83
4. Lift the ExpressCard module away from the upper cover.
84
Chapter 3
Removing the Mainboard
1. Remove the Upper Cover. See “Removing the Upper Cover” on page 71.
2. Use the tweezers to lift and remove the tape strip securing the modem cable.
3. Disconnect the two cables connected to the motherboard.
4. Remove the securing screw from the Mainboard.
Step
Mainboard
Chapter 3
Size
M2.5*6.5 (NL)
Quantity
Screw Type
1
85
5. Pull the edge of the lower base outward and lift the motherboard up to remove.
Removing the CPU Fan Module
1. See “Removing the Battery Pack” on page 46.
2. Remove the Mainboard. See “Removing the Mainboard” on page 85.
3. Turn the Mainboard right side up, and place it on a clean surface.
4. Using tweezers, grip the cable connector and disconnect the Fan cable from the Mainboard.
IMPORTANT:Do not grip the cable itself to prevent stripping.
5. Loosen the three captive screws from the heatsink.
86
Chapter 3
6. Lift the cover to expose the single securing screw. Remove the screw.
Step
Mainboard
Size
M2.5*6.5 (NL)
Quantity
Screw Type
1
7. Lift the Fan module clear of the Mainboard.
Removing the CPU
1. Remove the CPU Fan Module. See “Removing the CPU Fan Module” on page 86.
Chapter 3
87
2. Using a flat screwdriver, turn the CPU socket latch clockwise 180° to release the CPU.
k
3. Lift the CPU clear of the Mainboard.
88
Chapter 3
LCD Module Disassembly Process
LCD Module Disassembly Flowchart
Screw List
Step
Screw
LCD Bezel
M2.5*5 (NL)
4
Black
MA000007YG0
Inverter Board
M2.5*5 (NL)
1
Black
MA000007YG0
Camera Module
M2*3 (NL)
2
Black
MA0000060G0
LCD Panel
M2.5*5 (NL)
2
Black
MA000007YG0
LCD Brackets
M2*3 (NL)
8
Black
MA0000060G0
Chapter 3
Quantity
Color
Part No.
89
Removing the LCD Bezel
1. Remove the LCD Module. See “Removing the LCD Module” on page 69.
2. Remove the six rubber covers and screws.
Step
LCD Bezel
Size
M2.5*6.5 (NL)
Quantity
Screw Type
6
3. Starting from the inside edges, pry the inside of the bezel upwards from the panel. Continue moving left until
the bezel is removed. If necessary, use a plastic pry to release the corners of the bezel.
90
Chapter 3
4.
Lift up the bezel and remove it from the LCD Module.
Removing the Inverter Board
1. Remove the LCD Bezel. See “Removing the LCD Bezel” on page 90.
2. Disconnect the left and right Inverter board cables as shown.
3. Lift up the Inverter Board and remove.
Chapter 3
91
Removing the Camera Module
1. Remove the LCD Bezel. See “Removing the LCD Bezel” on page 90.
2. Remove the two securing screws from the Camera Module.
Step
Camera Module
Size
M2*3 (NL)
Quantity
Screw Type
1
3. Disconnect the Camera Module cable as shown.
92
Chapter 3
Removing the LCD Panel
1. Remove the LCD Bezel. See “Removing the LCD Bezel” on page 90.
2. Remove the six securing screws from the LCD Module.
Step
LCD Panel
Size
M2.5*6.5 (NL)
Quantity
Screw Type
6
3. Disconnect the left and right sides of the Inverter cable.
4. Disconnect the Camera Module cable as shown.
Chapter 3
93
5. Grasp the panel by both ends and lift to remove.
Removing the LCD Brackets and FPC Cable
1. Remove the LCD Panel. See “Removing the LCD Panel” on page 93.
2. Turn the LCD panel over to expose the rear. Grip the FPC cable and lift upward to detach the adhesive pads.
3. Remove the eight securing screws (four on each side) from the LCD Panel brackets.
Step
LCD Brackets
94
Size
M2*3 NL
Quantity
Screw Type
8
Chapter 3
4. Remove the LCD brackets by pulling away from the LCD Panel as shown.
Chapter 3
95
LCD Module Reassembly Procedure
Replacing the LCD Panel
1. Align the LCD brackets with the eight screw holes (four on each side) on the LCD Panel as shown.
2. Secure the LCD brackets to the LCD panel.
3. Turn the panel over. Insert the LCD Panel cable into the LCD Panel as shown.
96
Chapter 3
4. Align the LCD Panel cable as shown and press down to secure in place.
5. Take care to insert the top of the panel fist and then 6. Place the LCD Panel in the back cover.
angle the it in place.
7. Secure the LCD module with the six securing screws.
Chapter 3
97
8. Connect the left and right Inverter cables.
9. Connect the camera cable.
98
Chapter 3
Replacing the LCD Bezel
1. Starting from the bottom, locate the bezel correctly and press down the edges until there are no gaps
between the bezel and the LCD Module,
2. Replace the six screws and the rubber screw caps provided.
Chapter 3
99
Main Module Reassembly Procedure
Replacing the CPU
1. Carefully turn the mainboard upside down (CPU
2. Using a plastic screw driver, lock the CPU in the
side up), and insert the CPU into the CPU bracket
socket as shown.
as shown.
Replacing the CPU Fan Module
1. Replace the Fan module on the Mainboard.
2. Lift the cover to replace the single screw located in
the back of the fan module.
3. Tighten the three captive screws on the heatsink.
4. Connect the Fan cable to the Mainboard.
100
Chapter 3
Replacing the Mainboard
1. Pull the edge of the lower base outward and insert
the motherboard in the lower base.
2. Replace the securing screw on the Mainboard.
3. Connect the two cables connected to the motherboard.
4. Replace the adhesive strip securing the modem cable.
Chapter 3
101
Replacing the Bluetooth Board
1. Connect one end of the Bluetooth cable to the
mainboard as shown.
2. Connect the other end of the Bluetooth cable to the
Bluetooth Module as shown.
3. Locate the Bluetooth Module and replace the single securing screw.
Replacing the ExpressCard Module
1. Replace the ExpressCard module on the upper cover.
2. Replace the two securing screws.
IMPORTANT:The correct location of the ExpressCard Module screws is illustrated in the following image. Do
not insert the screws in the remaining screw sockets. They are locations for upper cover screws.
102
Chapter 3
3. Connect the cable connecting the ExpressCard module.
Replacing the Subwoofer Module
1. Grasp the Subwoofer Module and insert in the lower base.
2. Insert the cables under the housing guide as shown.
Chapter 3
103
3. Replace the four securing screws on the Subwoofer Module.
Replacing the Finger Print Reader
1. Remove the Finger Print Reader board from the Upper Cover.
104
Chapter 3
2. Remove the bracket from the board.
3. Replace the four securing screw on the Finger Print Reader board.
NOTE: Move back the cabling to allow for easier access to the screw sockets.
4. Connect the two FFC cables as shown.
Chapter 3
105
5. Connect the cable as shown.
Replacing the eKey Module
IMPORTANT:Take note of the eKey button when installing. It must face down and the cable connector up in
order to install the module correctly.
1. Locate and replace the module as shown.
2. Connect the eKey Module cable and replace the two securing screws.
106
Chapter 3
Replacing the Touch Pad
IMPORTANT:The Touch Pad cannot be removed individually. To replace the Touch Pad, replace the entire
Upper Cover.
1. Connect the Touch Pad cable as shown
Replacing the Launch Board
1. Replace the Launch Board on the upper cover.
2. Replace the four securing screws.
3. Insert the FFC flush with the connector and press down on the locking latch to secure.
Chapter 3
107
Replacing the Switch Board
1. Connect the cable to the Switch Board.
2. Insert the eKey board FFC flush with the connect and press down on the locking latch to secure.
3. Replace the two securing screws on the Switch Board.
108
Chapter 3
Replacing the Antenna, MIC and Speaker Cables
IMPORTANT:Ensure that all cables pass through the Mainboard and are accessible from the underside of
lower cover.
1. Insert the cabling through the housing as shown.
2. Ensure that the cabling is tucked in and secured.
3. Turn the computer on its side, feed cables through to the underside.
4. Place the computer upside down, and insert the MIC and Speaker cables through the HDD housing.
5. Take note of the cabling arrangement. Ensure that the cabling is secured as shown to prevent damage.
Chapter 3
109
6. Connect the MIC and speaker cables.
7. Gently pull the Antenna Cables through the HDD housing.
110
Chapter 3
Replacing the Speaker Module
1. Replace the Speaker Module from the upper cover.
2. Replace the four securing screws connecting the Speaker Module.
Replacing the Upper Cover
1. Locate the upper cover over the lower base taking note of the screw sockets.
Chapter 3
111
2. Angle the right end of the Upper Cover in place, and insert any remaining cables through the lower base as
shown.
3. Set the Upper Cover down on the lower base.
4. Replace the four securing screws on the Upper Cover.
112
Chapter 3
5. Connect the five cables from the mainboard as shown.
A
B
E
C
D
IMPORTANT:When removing cables, always hold the cable by the pull-tab or by the connector. Do not hold
the pull by the cable itself to prevent stripping.
Connect A as shown.
Connect B as shown.
Connect C as shown.
Connect D as shown.
Chapter 3
113
Connect E as shown.
6. Angle the keyboard plate to insert.
7. Tighten the captive screw on the keyboard plate.
114
Chapter 3
8. Turn the computer upside down and replace the eleven securing screws on the bottom panel to attach the
bottom and lower covers.
Replacing the Modem Module
1. Angle the Modem Module in place and attach to the connector.
2. Insert the module and replace the two securing screws.
Chapter 3
115
Replacing the Keyboard
1. Replace keyboard cable to the mainboard, and
secure the locking latch.
2. Turn the keyboard over and place the front edge
first in the mounting.
3. Press down on the areas marked below to secure in place.
116
Chapter 3
Replacing the Switch Cover
1. Replace the Switch cover, and press down to secure in place.
2. Turn the computer over and replace the nine securing screws.
Chapter 3
117
Replacing the ODD Module
1. Insert a pin in the eject hole of the ODD to eject the 2. Press the cover into the tray, bottom edge first, to
ODD tray.
secure.
3. Turn ODD Module around and secure bracket with 4. Slide Module in chassis and press until Module is
two screws.
flush with chassis.
5. Replace the ODD Cap and secure the single captive screw.
118
Chapter 3
Replacing the Hard Disk Drive2 Module
1. Replace the connector on the HDD.
2. Place the HDD in the HDD carrier.
3. Replace the four screws (two each side) to secure 4. Insert the HDD, right side first, and push down to
the carrier.
locate the interface correctly.
5. Replace the two securing screws.
Chapter 3
119
Replacing the Hard Disk Drive1 Module
1. Replace the connector on the HDD.
2. Place the HDD in the HDD carrier.
3. Replace the four screws (two each side) to secure 4. Insert the HDD, left side first, and push down to
the carrier.
locate the interface correctly.
5. Replace the two securing screws.
120
Chapter 3
Replacing the WLAN Board
1. Insert the WLAN board in to the socket.
2. Push the board down and replace the two securing
screws.
3. Replace the three antenna cables.
NOTE: The following is the correct cable-color to connector designation: TR1 (left) to White, TR3 (middle)
to Gray, and TR2 (right) to Black.
Chapter 3
121
Replacing the TV Tuner Module
1. Insert the TV Tuner board in to the socket.
2. Attach the bracket to the module.
3. Replace the three securing screws.
4. Replace the antenna cable.
122
Chapter 3
Replacing the Turbo Ram Module.
1. Insert the Turbo Ram board in to the socket.
2. Attach the bracket to the module.
3. Replace the three securing screws.
Replacing the MXM Module
1. Insert the MXM board in to the socket.
Chapter 3
2. Replace the four securing screws.
123
Replacing the DIMM Modules
1. Insert DIMM1 in to the socket.
2. Press down to locate DIMM correctly.
Requires new image
3. Repeat steps 1 and 2 for the second DIMM module.
Replacing the Lower Covers
1. Replace the HDD2 cover.
2. Replace the HDD1 cover.
3. Replace the Memory cover.
4. Secure the ten captive screws in the covers.
124
Chapter 3
Replacing the ExpressCard Dummy Tray
1. Insert the ExpressCard dummy as shown.
2. Push into the slot until flush with the chassis cover.
Replacing the SD Dummy Tray
1. Insert the SD dummy as shown.
2. Push into the slot until flush with the chassis cover.
Replacing the Battery
1. Slide and hold the battery release latch (1), insert
battery in to the main unit (2).
2. Slide the battery lock/unlock latch to the lock
position.
2
1
Chapter 3
125
126
Chapter 3
Chapter 4
Troubleshooting
Common Problems
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or
modified options can give false errors and invalid system responses.
1.
Obtain the failing symptoms in as much detail as possible.
2.
Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating
the same operation.
3.
Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified)
Go To
Power On Issue
Page 128
No Display Issue
Page 129
LCD Failure
Page 131
Internal Keyboard Failure
Page 131
Touch Pad Failure
Page 132
Internal Speaker Failure
Page 132
Internal Microphone Failure
Page 134
ODD Failure
Page 136
Rightside USB Failure
Page 139
Modem Failure
Page 139
WLAN Failure
Page 140
Acer EasyLaunch Button Failure
Page 140
Acer MediaTouch Failure
Page 141
Fingerprint Reader Failure
Page 141
Thermal Unit Failure
Page 142
HDTV Switch Failure
Page 142
Other Functions Failure
Page 143
Intermittent Failures
Page 144
Undermined Failures
Page 144
4.
If the Issue is still not resolved, see “Online Support Information” on page 197.
Chapter 4
127
Power On Issue
If the system doesn’t power on, perform the following actions one at a time to correct the problem. Do not
replace a non-defective FRUs:
Computer Shutsdown Intermittently
If the system powers off at intervals, perform the following actions one at a time to correct the problem.
128
1.
Check the power cable is properly connected to the computer and the electrical outlet.
2.
Remove any extension cables between the computer and the outlet.
3.
Remove any surge protectors between the computer and the electrical outlet. Plug the computer directly
into a known good electrical outlet.
4.
Disconnect the power and open the casing to check the Thermal Unit (see “Thermal Unit Failure” on page
142) and fan airways are free of obstructions.
5.
Disable the power management settings in the BIOS to ensure they are not the cause of the problem (see
“Power” on page 35).
6.
Remove all external and non-essential hardware connected to the computer that are not necessary to
boot the computer to the failure point.
7.
Remove any recently installed software.
8.
If the Issue is still not resolved, see “Online Support Information” on page 197.
Chapter 4
No Display Issue
If the Display doesn’t work, perform the following actions one at a time to correct the problem. Do not replace
a non-defective FRUs:
No POST or Video
If the POST or video doesn’t display, perform the following actions one at a time to correct the problem.
1.
Make sure that the internal display is selected. On this notebook model, switching between the internal
display and the external display is done by pressing Fn+F5. Reference Product pages for specific model
procedures.
2.
Make sure the computer has power by checking at least one of the following occurs:
•
Fans start up
•
Status LEDs light up
If there is no power, see “Power On Issue” on page 128.
3.
Drain any stored power by removing the power cable and battery and holding down the power button for
10 seconds. Reconnect the power and reboot the computer.
4.
Connect an external monitor to the computer and switch between the internal display and the external
display is by pressing Fn+F5 (on this model).
If the POST or video appears on the external display, see “LCD Failure” on page 131.
5.
Disconnect power and all external devices including port replicators or docking stations. Remove any
memory cards and CD/DVD discs. Restart the computer.
If the computer boots correctly, add the devices one by one until the failure point is discovered.
6.
Reseat the memory modules.
7.
Remove the drives (see “Disassembly Process” on page 44).
8.
If the Issue is still not resolved, see “Online Support Information” on page 197.
Chapter 4
129
Abnormal Video Display
If video displays abnormally, perform the following actions one at a time to correct the problem.
1.
Reboot the computer.
2.
If permanent vertical/horizontal lines or dark spots display in the same location, the LCD is faulty and
should be replaced. See “Disassembly Process” on page 44.
3.
If extensive pixel damage is present (different colored spots in the same locations on the screen), the LCD
is faulty and should be replaced. See “Disassembly Process” on page 44.
4.
Adjust the brightness to its highest level. See the User Manual for instructions on adjusting settings.
NOTE: Ensure that the computer is not running on battery alone as this may reduce display brightness.
If the display is too dim at the highest brightness setting, the LCD is faulty and should be replaced. See
“Disassembly Process” on page 44.
5.
Check the display resolution is correctly configured:
a.
Minimize or close all Windows.
b.
If display size is only abnormal in an application, check the view settings and control/mouse wheel
zoom feature in the application.
c.
If desktop display resolution is not normal, right-click on the desktop and select
Personalize´ Display Settings.
d.
Click and drag the Resolution slider to the desired resolution.
e.
Click Apply and check the display. Readjust if necessary.
6.
Roll back the video driver to the previous version if updated.
7.
Remove and reinstall the video driver.
8.
Check the Device Manager to determine that:
9.
•
The device is properly installed. There are no red Xs or yellow exclamation marks.
•
There are no device conflicts.
•
No hardware is listed under Other Devices.
If the Issue is still not resolved, see “Online Support Information” on page 197.
10. Run the Windows Memory Diagnostic from the operating system DVD and follow the onscreen prompts.
11. If the Issue is still not resolved, see “Online Support Information” on page 197.
Random Loss of BIOS Settings
If the computer is experiencing intermittent loss of BIOS information, perform the following actions one at a
time to correct the problem.
1.
If the computer is more than one year old, replace the CMOS battery.
2.
Run a complete virus scan using up-to-date software to ensure the computer is virus free.
3.
If the computer is experiencing HDD or ODD BIOS information loss, disconnect and reconnect the power
and data cables between devices.
If the BIOS settings are still lost, replace the cables.
130
4.
If HDD information is missing from the BIOS, the drive may be defective and should be replaced.
5.
Replace the Motherboard.
6.
If the Issue is still not resolved, see “Online Support Information” on page 197.
Chapter 4
LCD Failure
If the LCD fails, perform the following actions one at a time to correct the problem. Do not replace a nondefective FRUs:
Built-In Keyboard Failure
If the built-in Keyboard fails, perform the following actions one at a time to correct the problem. Do not replace
a non-defective FRUs:
Chapter 4
131
Touch Pad Failure
If the Touch Pad doesn’t work, perform the following actions one at a time to correct the problem. Do not
replace a non-defective FRUs:
Internal Speaker Failure
If the internal Speakers fail, perform the following actions one at a time to correct the problem. Do not replace
a non-defective FRUs:
132
Chapter 4
Sound Problems
If sound problems are experienced, perform the following actions one at a time to correct the problem.
1.
Reboot the computer.
2.
Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager. Check
the Device Manager to determine that:
•
The device is properly installed.
•
There are no red Xs or yellow exclamation marks.
•
There are no device conflicts.
•
No hardware is listed under Other Devices.
3.
Roll back the audio driver to the previous version, if updated recently.
4.
Remove and reinstall the audio driver.
5.
Ensure that all volume controls are set mid range:
a.
Click the volume icon on the taskbar and drag the slider to 50. Ensure that the volume is not muted.
b.
Click Mixer to verify that other audio applications are set to 50 and not muted.
6.
Navigate to Start´ Control Panel´ Hardware and Sound´ Sound. Ensure that Speakers are selected
as the default audio device (green check mark).
NOTE: If Speakers does not show, right-click on the Playback tab and select Show Disabled Devices
(clear by default).
7.
Select Speakers and click Configure to start Speaker Setup. Follow the onscreen prompts to configure
the speakers.
8.
Remove and recently installed hardware or software.
9.
Restore system and file settings from a known good date using System Restore.
If the issue is not fixed, repeat the preceding steps and select an earlier time and date.
10. Reinstall the Operating System.
11. If the Issue is still not resolved, see “Online Support Information” on page 197.
Chapter 4
133
Internal Microphone Failure
If the internal Microphone fails, perform the following actions one at a time to correct the problem. Do not
replace a non-defective FRUs:
Microphone Problems
If internal or external Microphones do no operate correctly, perform the following actions one at a time to
correct the problem.
1.
Check that the microphone is enabled. Navigate to Start´ Control Panel´ Hardware and Sound´
Sound and select the Recording tab.
2.
Right-click on the Recording tab and select Show Disabled Devices (clear by default).
3.
The microphone appears on the Recording tab.
4.
Right-click on the microphone and select Enable.
5.
Select the microphone then click Properties. Select the Levels tab.
6.
Increase the volume to the maximum setting and click OK.
7.
Test the microphone hardware:
8.
134
a.
Select the microphone and click Configure.
b.
Select Set up microphone.
c.
Select the microphone type from the list and click Next.
d.
Follow the onscreen prompts to complete the test.
If the Issue is still not resolved, see “Online Support Information” on page 197.
Chapter 4
HDD Not Operating Correctly
If the HDD does not operate correctly, perform the following actions one at a time to correct the problem.
1.
Disconnect all external devices.
2.
Run a complete virus scan using up-to-date software to ensure the computer is virus free.
3.
Run the Windows Vista Startup Repair Utility:
a.
insert the Windows Vista Operating System DVD in the ODD and restart the computer.
b.
When prompted, press any key to start to the operating system DVD.
c.
The Install Windows screen displays. Click Next.
d.
Select Repair your computer.
e.
The System Recovery Options screen displays. Click Next.
f.
Select the appropriate operating system, and click Next.
NOTE: Click Load Drivers if controller drives are required.
g.
Select Startup Repair.
h.
Startup Repair attempts to locate and resolve issues with the computer.
i.
When complete, click Finish.
If an issue is discovered, follow the onscreen information to resolve the problem.
4.
Run the Windows Memory Diagnostic Tool. For more information see Windows Help and Support.
5.
Restart the computer and press F2 to enter the BIOS Utility. Check the BIOS settings are correct and that
CD/DVD drive is set as the first boot device on the Boot menu.
6.
Ensure all cables and jumpers on the HDD and ODD are set correctly.
7.
Remove any recently added hardware and associated software.
8.
Run the Windows Disk Defragmenter. For more information see Windows Help and Support.
9.
Run Windows Check Disk by entering chkdsk /r from a command prompt. For more information see
Windows Help and Support.
10. Restore system and file settings from a known good date using System Restore.
If the issue is not fixed, repeat the preceding steps and select an earlier time and date.
11. Replace the HDD. See “Disassembly Process” on page 44.
Chapter 4
135
ODD Failure
If the ODD fails, perform the following actions one at a time to correct the problem. Do not replace a nondefective FRUs:
ODD Not Operating Correctly
If the ODD exhibits any of the following symptoms it may be faulty:
•
Audio CDs do not play when loaded
•
DVDs do not play when loaded
•
Blank discs do not burn correctly
•
DVD or CD play breaks up or jumps
•
Optical drive not found or not active:
•
Not shown in My Computer or the BIOS setup
•
LED does not flash when the computer starts up
•
The tray does not eject
•
Access failure screen displays
•
The ODD is noisy
Perform the following general solutions one at a time to correct the problem.
136
1.
Reboot the computer and retry the operation.
2.
Try an alternate disc.
3.
Navigate to Start´ Computer. Check that the ODD device is displayed in the Devices with Removable
Storage panel.
4.
Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager.
Chapter 4
a.
Double-click lDE ATA/ATAPI controllers. If a device displays a down arrow, right-click on the device
and click Enable.
b.
Double-click DVD/CD-ROM drives. If the device displays a down arrow, right-click on the device and
click Enable.
c.
Check that there are no yellow exclamation marks against the items in lDE ATA/ATAPI controllers. If
a device has an exclamation mark, right-click on the device and uninstall and reinstall the driver.
d.
Check that there are no yellow exclamation marks against the items in DVD/CD-ROM drives. If a
device has an exclamation mark, right-click on the device and uninstall and reinstall the driver.
e.
If the exclamation marker is not removed from the item in the lists, try removing any recently installed
software and retrying the operation.
Discs Do Not Play
If discs do not play when inserted in the drive, perform the following actions one at a time to correct the
problem.
1.
Check that the disc is correctly seated in the drive tray and that the label on the disc is visible.
2.
Check that the media is clean and scratch free.
3.
Try an alternate disc in the drive.
4.
Ensure that AutoPlay is enabled:
5.
a.
Navigate to Start´ Control Panel´ Hardware and Sound´ AutoPlay.
b.
Select Use AutoPlay for all media and devices.
c.
In the Audio CD and DVD Movie fields, select the desired player from the drop down menu.
Check that the Regional Code is correct for the selected media:
IMPORTANT:Region can only be changed a limited number of times. After Changes remaining reaches zero,
the region cannot be changed even Windows is reinstalled or the drive is moved to another computer.
a.
Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager.
b.
Double-click DVD/CD-ROM drives.
c.
Right-click DVD drive and click Properties, then click the DVD Region tab.
d.
Select the region suitable for the media inserted in the drive.
Discs Do Not Burn Properly
If discs can not be burned, perform the following actions one at a time to correct the problem.
1.
2.
Ensure that the default drive is record enabled:
a.
Navigate to Start´ Computer and right-click the writable ODD icon. Click Properties.
b.
Select the Recording tab. In the Desktop disc recording panel, select the writable ODD from the
drop down list.
c.
Click OK.
Ensure that the software used for burning discs is the factory default. If using different software, refer to
the software's user manual.
Playback is Choppy
If playback is choppy or jumps, perform the following actions one at a time to correct the problem.
1.
2.
Check that system resources are not running low:
a.
Try closing some applications.
b.
Reboot and try the operation again.
Check that the ODD controller transfer mode is set to DMA:
a.
Chapter 4
Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager.
137
b.
Double-click IDE ATA/ATAPI controllers, then right-click ATA Device 0.
c.
Click Properties and select the Advanced Settings tab. Ensure that the Enable DMA box is
checked and click OK.
d.
Repeat for the other ATA Devices shown if applicable.
Drive Not Detected
If Windows cannot detect the drive, perform the following actions one at a time to correct the problem.
1.
Restart the computer and press F2 to enter the BIOS Utility.
2.
Check that the drive is detected in the ATAPI Model Name field on the Information page.
NOTE: Check that the entry is identical to one of the ODDs specified in “Hardware Specifications and
Configurations” on page 18.
3.
Turn off the power and remove the cover to inspect the connections to the ODD. See “Disassembly
Process” on page 44.
a.
Check for broken connectors on the drive, motherboard, and cables.
b.
Check for bent or broken pins on the drive, motherboard, and cable connections.
c.
Try an alternate cable, if available. If the drive works with the new cable, the original cable should be
replaced.
4.
Reseat the drive ensuring and all cables are connected correctly.
5.
Replace the ODD. See “Disassembly Process” on page 44.
Drive Read Failure
If discs cannot be read when inserted in the drive, perform the following actions one at a time to correct the
problem.
1.
Remove and clean the failed disc.
2.
Retry reading the CD or DVD.
d.
Test the drive using other discs.
e.
Play a DVD movie
f.
Listen to a music CD
If the ODD works properly with alternate discs, the original disc is probably defective and should be
replaced.
3.
4.
138
Turn off the power and remove the cover to inspect the connections to the ODD. See “Disassembly
Process” on page 44.
a.
Check for broken connectors on the drive, motherboard, and cables.
b.
Check for bent or broken pins on the drive, motherboard, and cable connections.
c.
Try an alternate cable, if available. If the drive works with the new cable, the original cable should be
replaced.
Replace the ODD. See “Disassembly Process” on page 44.
Chapter 4
USB Failure (Rightside)
If the rightside USB port fails, perform the following actions one at a time to correct the problem. Do not
replace a non-defective FRUs:
Modem Function Failure
If the internal Modem fails, perform the following actions one at a time to correct the problem. Do not replace a
non-defective FRUs:
Chapter 4
139
Wireless Function Failure
If the WLAN fails, perform the following actions one at a time to correct the problem. Do not replace a nondefective FRUs:
EasyTouch Button Failure
If the Acer EasyTouch buttons fail, perform the following actions one at a time to correct the problem. Do not
replace a non-defective FRUs:
140
Chapter 4
MediaTouch Button Failure
If the Acer MediaTouch buttons fail, perform the following actions one at a time to correct the problem. Do not
replace a non-defective FRUs:
Fingerprint Reader Failure
If the Fingerprint Reader fails, perform the following actions one at a time to correct the problem. Do not
replace a non-defective FRUs:
Chapter 4
141
Thermal Unit Failure
If the Thermal Unit fails, perform the following actions one at a time to correct the problem. Do not replace a
non-defective FRUs:
HDTV Switch Failure
If the HDTV Switch fails, perform the following actions one at a time to correct the problem. Do not replace a
non-defective FRUs:
142
Chapter 4
External Mouse Failure
If an external Mouse fails, perform the following actions one at a time to correct the problem.
1.
Try an alternative mouse.
2.
If the mouse uses a wireless connection, insert new batteries and confirm there is a good connection. See
the mouse user manual.
3.
If the mouse uses a USB connection, try an alternate USB port.
4.
Try an alternative program to verify mouse operation. Reinstall the program experiencing mouse failure.
5.
Restart the computer.
6.
Remove any recently added hardware and associated software.
7.
Remove any recently added software and reboot.
8.
Restore system and file settings from a known good date using System Restore.
If the issue is not fixed, repeat the preceding steps and select an earlier time and date.
9.
Run the Event Viewer to check the events log for errors. For more information see Windows Help and
Support.
10. Roll back the mouse driver to the previous version if updated recently.
11. Remove and reinstall the mouse driver.
12. Check the Device Manager to determine that:
•
The device is properly installed. There are no red Xs or yellow exclamation marks.
•
There are no device conflicts.
•
No hardware is listed under Other Devices.
13. If the Issue is still not resolved, see “Online Support Information” on page 197.
Other Failures
If the CRT Switch, Dock, LAN Port, external MIC or Speakers, PCI Express Card, 5-in-1 Card Reader or
Volume Wheel fail, perform the following general steps to correct the problem. Do not replace a non-defective
FRUs:
1.
Check Drive whether is OK.
2.
Check Test Fixture is ok.
3.
Swap M/B to Try.
Chapter 4
143
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
1.
Run the advanced diagnostic test for the system board in loop mode at least 10 times.
2.
If no error is detected, do not replace any FRU.
3.
If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,
whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power On
Issue” on page 128.):
144
1.
Power-off the computer.
2.
Visually check them for damage. If any problems are found, replace the FRU.
3.
Remove or disconnect all of the following devices:
•
Non-Acer devices
•
Printer, mouse, and other external devices
•
Battery pack
•
Hard disk drive
•
DIMM
•
CD-ROM/Diskette drive Module
•
PC Cards
4.
Power-on the computer.
5.
Determine if the problem has changed.
6.
If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7.
If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
•
System board
•
LCD assembly
Chapter 4
POST Codes Tables
These tables describe the chipset and core POST codes, functions, phases, and components for the POST.
Chipset POST Codes
The following table details the chipset POST codes and functions used in the POST.
POST Code
Function
Phase
Component
0xA0
MRC Entry
PEI
chipset/MRC
0x01
Enable MCHBAR
PEI
chipset/MRC
0x02
Check ME existence
PEI
chipset/MRC
0x03
Check for DRAM initialization interrupt and reset fail
PEI
chipset/MRC
0x04
Determine the system Memory type based on first
populated socket
PEI
chipset/MRC
0x05
Verify all DIMMs are DDR2 and SO-DIMMS, which
are unbuffered
PEI
chipset/MRC
0x06
Verify all DIMMs are Non-ECC
PEI
chipset/MRC
0x07
Verify all DIMMs are single or double sided and not
mixed
PEI
chipset/MRC
0x08
Verify all DIMMs are x8 or x16 width
PEI
chipset/MRC
0x09
Calculate number of Row and Column bits
PEI
chipset/MRC
0x10
Calculate number of banks for each DIMM
PEI
chipset/MRC
0x11
Determine raw card type
PEI
chipset/MRC
0x12
Find a common CAS latency between the DIMMS
and the MCH
PEI
chipset/MRC
0x13
Determine the memory frequency and CAS latency
to program
PEI
chipset/MRC
0x14
Determine the smallest common timing value for all
DIMMS
PEI
chipset/MRC
0x17
Power management resume
PEI
chipset/MRC
0x18
Program DRAM type (DDR2/DDR3) and Power up
sequence
PEI
chipset/MRC
0x19
Program the correct system memory frequency
PEI
chipset/MRC
0x20
Program the correct Graphics memory frequency
PEI
chipset/MRC
0x21
Early DRC initialization
PEI
chipset/MRC
0x22
Program the DRAM Row Attributes and DRAM Row
Boundary registers PRE JEDEC.
PEI
chipset/MRC
0x23
Program the RCOMP SRAM registers
PEI
chipset/MRC
0x24
Program DRAM type (DDR2/DDR3) and Power up
sequence
PEI
chipset/MRC
0x25
Program the DRAM Timing
PEI
chipset/MRC
0x26
Program the DRAM Bank Architecture register
PEI
chipset/MRC
0x27
Enable all clocks on populated rows
PEI
chipset/MRC
0x28
Program MCH ODT
PEI
chipset/MRC
0x29
Program tRD
PEI
chipset/MRC
0x30
Miscellaneous Pre JEDEC steps
PEI
chipset/MRC
0x31
Program clock crossing registers
PEI
chipset/MRC
Chapter 4
145
POST Code
Function
Phase
Component
0x32
Program the Egress port timings
PEI
chipset/MRC
0x33
Program the Memory IO registers
PEI
chipset/MRC
0x34
Perform steps required before JEDEC
PEI
chipset/MRC
0x35
Perform JEDEC memory initialization for all memory
rows
PEI
chipset/MRC
0x36
Setup DRAM control register for normal operation
and enable
PEI
chipset/MRC
0x37
Do ZQ calibration for DDR3
PEI
chipset/MRC
0x38
Perform final Dra/Drb programming, Set the mode of
operation for the memory channels
PEI
chipset/MRC
0x39
Set Enhanced addressing mode for each channel
PEI
chipset/MRC
0x40
Perform steps required after JEDEC init
PEI
chipset/MRC
0x41
Program the receive enable reference timing control
register
PEI
chipset/MRC
0x42
Post receive enable initialization
PEI
chipset/MRC
0x43
Enable sense amps. Reset read/write DQS pointers
PEI
chipset/MRC
0x44
Perform ME steps
PEI
chipset/MRC
0x45
Clear DRAM initialization bit in the ICH.
PEI
chipset/MRC
0x46
Program Thermal Management
PEI
chipset/MRC
0x47
Program TS on DIMM
PEI
chipset/MRC
0x48
Program TS on Board
PEI
chipset/MRC
0xAF
Exit MRC
PEI
chipset/MRC
0xE0
#define MEM_ERR_BAD_DIMM (S11)
PEI
chipset/MRC
0xE1
#define MEM_ERR_ECC_DIMM (S06)
PEI
chipset/MRC
0xE2
#define MEM_ERR_SIDES (S07)
PEI
chipset/MRC
0xE3
#define MEM_ERR_WIDTH (S08, S10)
PEI
chipset/MRC
0xE4
#define MEM_ERR_TRFC (FindTrasTrpTrcd)
PEI
chipset/MRC
0xE5
#define MEM_ERR_CAS_LATENCY (S12, S13)
PEI
chipset/MRC
0xE6
#define MEM_ERR_REFRESH (ProgDrt)
PEI
chipset/MRC
0xE7
#define MEM_ERR_BL8 (S14)
PEI
chipset/MRC
0xE9
#define MEM_ERR_FREQUENCY (findTCLTacTClk,
S13, S12, ProgramGraphicsFrequency,
ProgMchOdt, GetPlatformData)
PEI
chipset/MRC
0xEA
#define MEM_ERR_SIZE (S14)
PEI
chipset/MRC
0xEC
#define MEM_ERR_TRAS (FindTrasTrpTrcd)
PEI
chipset/MRC
0xED
#define MEM_ERR_TRP (FindTrasTrpTrcd)
PEI
chipset/MRC
0xEE
#define MEM_ERR_TRCD (FindTrasTrpTrcd)
PEI
chipset/MRC
0xEF
#define MEM_ERR_TWR (FindTrasTrpTrcd)
PEI
chipset/MRC
0xF0
#define MEM_ERR_RCVEN_FINDLOW
(CalibrateRcvenForGroup)
PEI
chipset/MRC
0xF1
#define MEM_ERR_RCVEN_FINDEDGE
(CalibrateRcvenForGroup)
PEI
chipset/MRC
0xF2
#define MEM_ERR_RCVEN_FINDPREAMBLE
(CalibrateRcvenForGroup)
PEI
chipset/MRC
0xF6
#define MEM_ERR_RCVEN_PREAMBLEEDGE
(CalibrateRcvenForGroup)
PEI
chipset/MRC
146
Chapter 4
POST Code
Function
Phase
Component
0xF3
#define MEM_ERR_RCVEN_FINDCENTER
(CalibrateRcvenForGroup)
PEI
chipset/MRC
0xFZ
#define MEM_ERR_TYPE (S11, S04)
PEI
chipset/MRC
0xF5
#define MEM_ERR_RAWCARD (S11)
PEI
chipset/MRC
0xFA
#define MEM_ERR_SFF (ProgWrioDll)
PEI
chipset/MRC
0xFB
#define MEM_ERR_THERMAL (ProgramThrottling)
PEI
chipset/MRC
0xA0xx
Launch BIOS ACMSclean
PEI
chipset/TXT
0xA4xx
Launch BIOS ACMScheck
PEI
chipset/TXT
0xE5
Wait for ME ready
DXE
HECI/iAMT
0xE6
ME Ready
DXE
HECI/iAMT
Core POST Codes
The following table details the core POST codes and functions used in the POST.
POST Code
Function
Phase
Component
0x00
Early Microcode update for CAR
CEI / SEC
Core
0x01
Enable CAR
CEI / SEC
Core
0x02
CAR Done, initial stack
CEI / SEC
Core
0xEE
unknown CPU ID to load uCode
CEI / SEC
CPU
0xEF
unknown DT CPU to load uCode
CEI / SEC
CPU
0xnn
File count found in a volume
PEI
Core
0x11
Debug Test driver for debug test PPI 1 (If install
debugTest driver)
PEI
Core
0x22
Debug Test driver for debug test PPI 2 (If install
debugTest driver)
PEI
Core
0x33
Debug Test driver for debug test PPI 3 (If install
debugTest driver)
PEI
Core
0x44
Entry point of loadfile
PEI
Core
0x88
Entry point of apMuLoader
PEI
Core
0x80
A PEIM found
PEI
Core
0x82
PEIM not dispatched yet
PEI
Core
0x84
PEIM satisfies depex
PEI
Core
0x86
Image loaded but fail on security
PEI
Core
0x88
Executing a PEIM
PEI
Core
0x8A
Processing notify event for newly installed PPI
PEI
Core
0x8C
Handing off to next phase (DXE)
PEI
Core
0x8F
Fail to hand off to next phase, system halt
PEI
Core
0x90
All PEIM dispatched! Going to DxeIpl
PEI
Core
0xCC
AP Micro-code update
PEI
Core
0x20
S3 resume entry
S3 resume
Core
0x21
Start running Boot-time bootscripts
S3 resume
Core
0x22
Start running Run-time bootscripts
S3 resume
Core
0x23
End of S3 resume, jump back to Waking vector
S3 resume
Core
0x80
Initialize the chipset
Crisis Recovery
Core
0x81
Initialize the bridge
Crisis Recovery
Core
Chapter 4
147
POST Code
Function
Phase
Component
0x82
Initialize the CPU
Crisis Recovery
Core
0x89
Set Huge Segment
Crisis Recovery
Core
0x83
Initialize system timer
Crisis Recovery
Core
0x84
Initialize system I/O
Crisis Recovery
Core
0x88
Initialize Multi Processor
Crisis Recovery
Core
0x8A
Initialize OEM special code
Crisis Recovery
Core
0x8B
Initialize PIC and DMA
Crisis Recovery
Core
0x8C
Initialize Memory type
Crisis Recovery
Core
0x8D
Initialize Memory size
Crisis Recovery
Core
0x8F
Initialize SMM
Crisis Recovery
Core
0x90
System memory test
Crisis Recovery
Core
0x91
Initialize interrupt vectors
Crisis Recovery
Core
0x92
Initialize Run Time Clock
Crisis Recovery
Core
0x99
Initialize security
Crisis Recovery
Core
0x93
Initialize video
Crisis Recovery
Core
0x94
Output one beep
Crisis Recovery
Core
0x98
USB Initialization
Crisis Recovery
Core
0x95
Initialize the installed boot devices
Crisis Recovery
Core
0x96
Clear Huge segment
Crisis Recovery
Core
0x97
Boot Crisis Disk
Crisis Recovery
Core
0x20
DXE starts
DXE
Core
0x30
BIOSPSM
DXE
Core
0x02
BIOSBlockIO
DXE
Core
0x00
BIOSPSM Exception Handler - Divide error
BIOSPSM
Core
0x38
Cannot locate LegacyRegion DXE
BIOSPSM
Core
0xB1
ACPISupport driver Installed
DXE
Core
0xE0
BDS Entry
DXE
Core
0x07
IA32 variable driver entry
DXE
Core
0x0D
conspliter driver entry
DXE
Core
0x10
partition driver entry
DXE
Core
0x49
pciRootBridge driver entry
DXE
Core
0xC6
pciBusDriver entry
DXE
Core
0xE0
Go to legacy BIOS or BDS Entry Point
DXE
Core
0x90
Start Image
DXE
Core
0x90
Start Image Successfully
DXE
Core
0x90
Start Image Failed
DXE
Core
0x33
Debug Test driver for debug test PPI 1
DXE
Core
0x22
Debug Test driver for debug test PPI 2
DXE
Core
0x11
Debug Test driver for debug test PPI 3
DXE
Core
0x02
Invalid event # for measuring Separator Event
DXE
TCG
0x02
Invalid event # for measuring Separator Event
DXE
TCG
0x02
PCR Index over limit (PCR > 23)
DXE
TCG
0x02
TCG copy memory failed
DXE
TCG
148
Chapter 4
POST Code
Function
Phase
Component
0x09
TCG log event failed
DXE
TCG
0x09
Setup event log failed
DXE
TCG
0x12
TIS set active locality failed
DXE
TCG
0x12
TIS relinquish active locality failed
DXE
TCG
0x12
TIS wait command ready failed (prepare to send)
DXE
TCG
0x12
TIS abort 'send 'command due to timeout
DXE
TCG
0x12
TIS abort 'sendAndGo 'command due to timeout
DXE
TCG
0x04
TIS wait bit set failed before send last byte
DXE
TCG
0x12
TIS abort command due to timeout before send last
byte
DXE
TCG
0x04
TIS wait bit clear failed when sending last byte
DXE
TCG
0x22
TCG Physical Presence execution
DXE
TCG
0xB1
TCG DXE common pass through
DXE
TCG
0xE3
First Legacy BIOS Task table for legacy reset
LBT
Core
0x20
Verify that DRAM refresh is operating by polling the
refresh bit in PORTB.
LBT
Core
0xDA
Dummy PCIE Init entry, now handled by driver
LBT
Core
0x29
PMM (POST Memory Manager) init
LBT
Core
0xE5
WHEA init
LBT
Core
0x33
PDM (Post Dispatcher Manager) init
LBT
Core
0x01
IPMI init
LBT
Core
0xD8
ASF Init
LBT
Core
0x09
Set in-POST flag in CMOS that indicates we are in
POST. If this bit is not cleared by
postClearBootFlagJ (AEh), the TrustedCore on next
boot determines that the current configuration
caused POST to fail and uses default values for
configuration.
LBT
Core
0x2B
Enhanced CMOS init
LBT
Core
0xE0
EFI Variable Init
LBT
Core
0xC1
PEM (Post Error Manager) init
LBT
Core
0x3B
Debug Service Init (ROM Polit)
LBT
Core
0xDC
POST Update Error
LBT
Core
0x3A
Autosize external cache and program cache size for
enabling later in POST.
LBT
Core
0x0B
Enable CPU cache. Set bits in cmos related to
cache.
LBT
Core
0x0F
Enable the local bus IDE as primary or secondary
depending on other drives detected.
LBT
Core
0x10
Initialize Power Management.
LBT
Core
0x14
Verify that the 8742 keyboard controller is
responding. Send a self-test command to the 8742
and wait for results. Also read the switch inputs from
the 8742 and write the keyboard controller command
byte.
LBT
Core
Chapter 4
149
POST Code
Function
Phase
Component
0x1A
Initialize DMA command register with these settings:
1. Memory to memory disabled 2. Channel 0 hold
address disabled 3. Controller enabled 4. Normal
timing 5. Fixed priority 6. Late write selection 7.
DREQ sense active 8. DACK sense active low.
LBT
Core
0x22
Reset the keyboard.
LBT
Core
0x40
Test A20 line
LBT
Core
0x67
Quick initialization of all Application Processors in a
multi-processor system
LBT
Core
0x32
Compute CPU speed.
LBT
Core
0x69
Initialize the handler for SMM.
LBT
Core
0x6B
If CMOS is bad, load Custom Defaults from flash into
CMOS. If successful, reboot.
LBT
Core
0x3C
If CMOS is valid, load chipset registers with values
from CMOS, otherwise load defaults and display
Setup prompt. If Auto Configuration is enabled,
always load the chipset registers with the Setup
defaults (Rel 6.0).
LBT
Core
0x3D
Load alternate registers with CMOS values
LBT
Core
0x42
Initialize interrupt vectors 0 thru 77h
LBT
Core
0x46
Verify the ROM copyright notice
LBT
Core
0x45
Initialize all motherboard devices.
LBT
Core
0x49
1. Size the PCI bus topology and set bridge bus
numbers. 2. Set the system max bus number. 3.
Write a 0 to the command register of every PCI
device. 4. Write a 0 to all 6 base registers in every
PCI device. 5. Write a -1 to the status register of
every PC
LBT
Core
0xC6
Initialize note dock
LBT
Core
0xC5
PnPnd dual CMOS (optional)
LBT
Core
0x48
Verify that the equipment specified in the CMOS
matches the hardware currently installed. If the
monitor type is set to 00 then a video ROM must
exist. If the monitor type is 1 or 2 set the video switch
to CGA. If monitor type 3, set the video switch to m
LBT
Core
0xD1
Initialize BIOS stack
LBT
Core
0xD3
Setup E820h and WAD memory map
LBT
Core
0x24
Set segment-register addressability to 4 GB
LBT
Core
0xCC
Redirect Int 10h to enable target board to use a
remote serial video (PICO BIOS).
LBT
Core
0x8A
Initialize Extended BIOS Data Area and initialize the
mouse.
LBT
Core
0x9D
Initialize Security Engine.
LBT
Core
0x55
USB Initialization
LBT
Core
0x52
Verify keyboard reset.
LBT
Core
0x54
Initialize keystroke clicker if enabled in Setup.
LBT
Core
0x76
Check status bits for keyboard-related failures.
Display error messages on the screen.
LBT
Core
0x4A
Initialize all video adapters in system
LBT
Core
150
Chapter 4
POST Code
Function
Phase
Component
0x4C
Shadow video BIOS ROM if specified by Setup, and
CMOS is valid and the previous boot was OK.
LBT
Core
0x59
Register POST Display Services, fonts, and
languages with the POST Dispatch Manager.
LBT
Core
0x57
Initialize 1394 Firewire
LBT
Core
0xD6
Initialize PC card
LBT
Core
0x58
Test for unexpected interrupts. First do an STI for hot
interrupts. Secondly, test the NMI for an unexpected
interrupt. Thirdly, enable the parity checkers and
read from memory, checking for an unexpected
interrupt.
LBT
Core
0x3F
ROMPolit memory init
LBT
Core
0xC4
Install the IRQ vectors (Sever Hotkey)
LBT
Core
0x7C
Initialize the hardware interrupt vectors from 08 to 0F
and from 70h to 77H. Also set the interrupt vectors
from 60h to 66H to zero.
LBT
Core
0x41
ROM Pilot Init
LBT
Core
0x4B
Initialize QuietBoot if it is installed. Enable both
keyboard and timer interrupts (IRQ0 and IRQ1). If
your POST tasks require interrupts off, preserve
them with a PUSHF and CLI at the beginning and a
POPF at the end.
LBT
Core
0xDE
Initialize and UNDI ROM (fro remote flash)
LBT
Core
0xC6
Initial and install console for UCR
LBT
Core
0x4E
Display copyright notice.
LBT
Core
0xD4
Get CPU branding string
LBT
Core
0x50
Display CPU type and speed
LBT
Core
0xC9
pretask before EISA init
LBT
Core
0x51
EISA Init
LBT
Core
0x5A
Display prompt "Press F2 to enter SETUP"
LBT
Core
0x5B
Disable CPU cache.
LBT
Core
0x5C
Test RAM between 512K and 640K.
LBT
Core
0x60
Determine and test the amount of extended memory
available. Determine if memory exists by writing to a
few strategic locations and see if the data can be
read back. If so, perform an address-line test and a
RAM test on the memory.
LBT
Core
0x62
The amount of memory available. This test is
dependent on the processor, since the test will vary
depending on the width of memory (16 or 32 bits).
This test will also use A20 as the skew address to
prevent corruption of the system memory.
LBT
Core
0x64
Jump to UserPatch1.
LBT
Core
0x66
Set cache registers to their CMOS values if CMOS is
valid, unless auto configuration is enabled, in which
case load cache registers from the Setup default
table.
LBT
Core
0x68
Enable external cache and CPU cache if present.
Configure non-cacheable regions if necessary.
LBT
Core
Chapter 4
151
POST Code
Function
Phase
Component
0x6A
Display external cache size on the screen if it is nonzero.
LBT
Core
0x6C
Display shadow message
LBT
Core
0xCA
post EISA init
LBT
Core
0x70
Check flags in CMOS and in the TrustedCore data
area for errors detected during POST. Display error
messages on the screen.
LBT
Core
0x72
Check status bits to see if configuration problems
were detected. If so, display error messages on the
screen.
LBT
Core
0x4F
Initialize MultiBoot. Allocate memory for old and new
MultiBoot history tables.
LBT
Core
0xCD
Reclaim console vector after HW vectors initialized.
LBT
Core
0x7D
Initialize Intelligent System Monitoring.
LBT
Core
0x7E
The Coprocessor initialization test. Use the floating
point instructions to determine if a coprocessor
exists instead of the ET bit in CR0.
LBT
Core
0xC1
Check Boot Type (Server BIOS)
LBT
Core
0x80
Disable onboard COM and LPT ports before testing
for presence of external I/O devices.
LBT
Core
0xCA
Redirect Int 15h to enable target board to use remote
keyboard (PICO BIOS).
LBT
Core
0x88
Initialize interrupt controller.
LBT
Core
0x81
Run late device initialization routines.
LBT
Core
0x87
Initialize motherboard configurable devices.
LBT
Core
0x85
Display any ESCD read errors and configure all PnP
ISA devices.
LBT
Core
0x82
Test and identify RS232 ports.
LBT
Core
0x84
Test and identify parallel ports.
LBT
Core
0x86
Initialize onboard I/O and BDA according to CMOS
and presence of external devices.
LBT
Core
0x83
Configure Fisk Disk Controller.
LBT
Core
0xCE
Initialize digitizer device and display installed
message if successful.
LBT
Core
0x89
Enable non-maskable interrupts.
LBT
Core
0x8C
Initialize both of the floppy disks and display an error
message if failure was detected. Check both drives
to establish the appropriate diskette types in the
TrustedCore data area
LBT
Core
0xCB
Redirect Int 13h to Memory Technologies Devices
such as ROM, RAM, PCMCIA, and serial disk (PICO
BIOS).
LBT
Core
0xCD
Remap I/O and memory address space for PCMCIA
(PICO BIOS).
LBT
Core
0x90
Initialize hard-disk controller. If the CMOS ram is
valid and intact, and fixed disks are defined, call the
fixed disk init routine to initialize the fixed disk
system and take over the appropriate interrupt
vectors.
LBT
Core
152
Chapter 4
POST Code
Function
Phase
Component
0x8B
Setup interrupt vector and present bit in Equipment
byte.
LBT
Core
0x95
1. Check CMOS for CD-ROM drive present 2.
Activate the drive by checking for media present 3.
Check sector 11h (17) for Boot Record Volume
Descriptor 4. Check the boot catalog for validity 5.
Pick a boot entry 6. Create a Specification Packet
LBT
Core
0x92
Jump to UserPatch2.
LBT
Core
0xB6
If password on boot is enabled, a call is made to
Setup to check password. If the user does not enter
a valid password, Setup does not return.
LBT
Core
0x98
Search for option ROMs. Rom scan the area from
C800h for a length of BCP_ROM_Scan_Size (or to
E000h by default) on every 2K boundary, looking for
add on cards that need initialization.
LBT
Core
0x93
Build the MPTABLE for multi-processor boards
LBT
Core
0xD9
IPMI late init
LBT
Core
0x9C
Set up Power Management. Initiate power management state machine.
LBT
Core
0xC7
Late note dock init
LBT
Core
0x9E
Enable hardware interrupts
LBT
Core
0xA0
Setup time tick for current date/time
LBT
Core
0xA2
Setup Numlock indicator. Display a message if key
switch is locked.
LBT
Core
0xA4
Initialize typematic rate
LBT
Core
0xDB
StrongROM Test
LBT
Core
0xE2
OEM security key test
LBT
Core
0xC2
Write PEM errors.
LBT
Core
0xBA
Initialize the SMBIOS header and sub-structures.
LBT
Core
0xC3
Display PEM errors.
LBT
Core
0xA8
Overwrite the "Press F2 for Setup" prompt with
spaces, erasing it from the screen.
LBT
Core
0xAA
Scan the key buffer to see if the F2 key was struck
after keyboard interrupts were enabled. If an F2
keystroke is found, set a flag.
LBT
Core
0xE1
Start Periodic Timer (TC Subscribe)
LBT
Core
0xAC
Check if "Enter SETUP" is pressed.
LBT
Core
0x8F
Count the number of ATA drives in the system and
update the number in bdaFdiskcount.
LBT
Core
0x91
Configure the local bus IDE timing register based on
the drives attached to it.
LBT
Core
0x9F
Check the total number of Fast Disks (ATA and
SCSI) and update the bdaFdiskCount.
LBT
Core
0xD7
Check if FirstWare HPA exists
LBT
Core
0xAE
Clear ConfigFailedBit and InPostBit in CMOS.
LBT
Core
0xB0
Check for errors and decide if needs to run Setup.
LBT
Core
0xB2
Change status bits in CMOS and/or the TrustedCore
data area to reflect the fact that POST is complete.
LBT
Core
Chapter 4
153
POST Code
Function
Phase
Component
0xB5
Fade out OEM Logo or post string
LBT
Core
0xC5
End hotkey detection (Server BIOS)
LBT
Core
0xBE
If BCP option is enabled, clear the screen before
booting.
LBT
Core
0xB6
If password on boot is enabled, a call is made to
Setup to check password. If the user does not enter
a valid password, Setup does not return.
LBT
Core
0xBC
Clear parity-error latch
LBT
Core
0xB7
Initialize ACPI BIOS.
LBT
Core
0x9B
Enable CPU management (Geyserville I)
LBT
Core
0xBD
Display Boot First menu if MultiBoot is installed and
hotkey pressed.
LBT
Core
0xBF
Check virus and backup reminders.
LBT
Core
0x97
Create pointer to MP table in Extended BDA.
LBT
Core
0x99
Check support status for Self-Monitoring Analysis
Reporting Technology (disk-failure warning).
LBT
Core
0xB1
Unload ROM Pilot
LBT
Core
0xDD
Perform remote flash if requested
LBT
Core
0xC7
If UCR redirection is installed, remove display
manager and unhook INT10
LBT
Core
0XDF
Shutdown the PXE UNDI code
LBT
Core
0xB3
Store enhanced CMOS values in non-volatile area
LBT
Core
0xE4
Last Legacy BIOS Task before hand off to UEFI/DXE
LBT
Core
0xB9
Clear all screen graphics before booting.
bootLegacy
Core
0xC0
INT19 entry for legacy boot
bootLegacy
Core
0xEF
Invalid AP #
SDXE
Core
0xEF
Non-Yohna and non-Morem class CPU found for
SDXE (getTSCFreq)
SDXE
Core
0xEE
AP cannot synch BSP in SDXE (syncWithBSP)
SDXE
Core
0xEE
BSP cannot synch w/ AP in SDXE (syncWithAP)
SDXE
Core
154
Chapter 4
Chapter 5
Jumper and Connector Locations
Top View
1
2
3
4
5
6
8
7
No.
Chapter 5
Description
No.
Description
1
LCD Connector
5
MDC Connector
2
Powerboard Connector
6
ExpressCard Board Connector
3
Keyboard Connector
7
BLuetooth Connector
4
DDR3 Connector
8
PCMCIA Connector
155
Bottom View
1
2
3
17
16
15
14
13
4
12
11
10
5
9
8
No.
156
Description
7
6
No.
Description
1
CPU Socket
10
Audio Connector
2
DDR2 Connector
11
SPDIF Connector
3
Battery Connector
12
USB Connector
4
ODD Connector
13
HDMI Connector
5
HDD Connector
14
CRT Connector
6
Card Reader Connector
15
Docking Connector
7
HDD Connector
16
RJ 45
8
MXM Connector
17
DC Jack
9
Audio Connector
Chapter 5
Clearing Password Check and BIOS Recovery
This section provide you the standard operating procedures of clearing password and BIOS recovery for
Aspire 7730/7730G. Aspire 7730/7730G provide one Hardware Open Gap on main board for clearing
password check, and one Hotkey for enabling BIOS Recovery.
Clearing Password Check
Hardware Open Gap Description
Item
R347 (RTC_RST)
Description
Clear CMOS Jumper
Steps for Clearing BIOS Password Check
If users set BIOS Password (Supervisor Password and/or User Password) for a security reason, BIOS will ask
the password during systems POST or when systems enter to BIOS Setup menu. However, once it is
necessary to bypass the password check, users need to short the HW Gap to clear the password by the
following steps:
•
Power Off a system, and remove HDD, AC and Battery from the machine.
•
Open the back cover of the machine, and find out the HW Gap on M/B as picture.
•
Use an electric conductivity tool to short the two points of the HW Gap.
•
Plug in AC, keep the short condition on the HW Gap, and press Power Button to power on the
system till BIOS POST finish. Then remove the tool from the HW Gap.
•
Restart system. Press F2 key to enter BIOS Setup menu.
If there is no Password request, BIOS Password is cleared. Otherwise, please follow the steps and
try again.
NOTE: The steps are only for clearing BIOS Password (Supervisor Password and User Password).
•
Chapter 5
157
BIOS Recovery by Crisis Disk
BIOS Recovery Boot Block:
BIOS Recovery Boot Block is a special block of BIOS. It is used to boot up the system with minimum BIOS
initialization. Users can enable this feature to restore the BIOS firmware to a successful one once the previous
BIOS flashing process failed.
BIOS Recovery Hotkey:
The system provides a function hotkey: Fn+Esc, for enable BIOS Recovery process when system is powered
on during BIOS POST. To use this function, it is strongly recommended to have the AC adapter and Battery
present. If this function is enabled, the system will force the BIOS to enter a special BIOS block, called Boot
Block.
Steps for BIOS Recovery from USB Storage:
Before doing this, prepare the Crisis USB key. The Crisis USB key could be made by executing the Crisis Disk
program in another system with Windows XP OS.
Follow the steps below:
1.
Save ROM file (file name: JAL90x64.fd) to the root directory of USB storage.
2.
Plug USB storage into USB port.
3.
Press Fn + ESC button then plug in AC.
The Power button flashes once.
4.
Press Power button to initiate system CRISIS mode.
When CRISIS is complete, the system auto restarts with a workable BIOS.
5.
158
Update the latest version BIOS for this machine by regular BIOS flashing process.
Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of Aspire 7730/7730G. Refer to this
chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your
regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service
Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code from
those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer
office to order FRU parts for repair and service of customer machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how to
dispose it properly, or follow the rules set by your regional Acer office on how to return it.
Chapter 6
159
Aspire 7730/7730G Exploded Diagrams
Upper Cover
Number
Description
Part Number
1
2
3
4
5
6
7
160
Chapter 6
Lower Cover
Number
Description
Part Number
1
2
3
4
Chapter 6
161
LCD Panel
Number
Description
Part Number
1
2
3
4
5
6
7
8
9
10
162
Chapter 6
Aspire 7730/7730G FRU List
Category
Description
Part Number
Adapter
ADAPTER 65W 3PIN DELTA SADP-65KB DFA
AP.06501.013
ADAPTER 65W LITEON PA-1650-02AC LF
AP.06503.016
ADAPTER 65W 3PIN HIPRO AC-OK065B13
AP.0650A.010
ADAPTER DELTA 90W ADP-90SB BBEA LF
AP.09001.013
ADAPTER LITE-ON 90W 19V BLUE PA-1900-24AR LED LF
AP.09003.011
ADAPTER HIPRO 90W 19V BLUE HP-OL093B13P LED LF
LEVEL 4
AP.0900A.001
Battery SONY AS-2007B Li-Ion 3S2P SONY 6 cell 4400mAh
Main COMMON Normal Type
BT.00604.025
Battery PANASONIC AS-2007B Li-Ion 3S2P PANASONIC 6
cell 4400mAh Main COMMON PSS
BT.00605.021
Battery SANYO AS-2007B Li-Ion 3S2P SANYO 6 cell
4400mAh Main COMMON Normal Type
BT.00603.042
Battery SIMPLO AS-2007B Li-Ion 3S2P PANASONIC 6 cell
4400mAh Main COMMON PSS
BT.00607.016
Battery PANASONIC AS-2007B Li-Ion 4S2P PANASONIC 8
cell 4800mAh Main COMMON
BT.00805.011
Battery SANYO AS-2007B Li-Ion 4S2P SANYO 8 cell
4800mAh Main COMMON
BT.00803.024
Battery SIMPLO AS-2007B Li-Ion 4S2P PANASONIC 8 cell
4800mAh Main COMMON PSS
BT.00807.015
Battery SONY AS-2007B Li-Ion 4S2P SONY 8 cell 4800mAh
Main COMMON
BT.00804.020
Foxconn Delphi-AM5 V2H 1.5_3.3v T60M951.41
FX.22500.022
BLUETOOTH MODULE (T60H928.11)
BT.21100.005
WIRELESS LAN CARD FOXCONN T60h976.00 MINI
54.AZL07.001
WIRELESS LAN BOARD 802.11BG FOXCONN BCM4312
T77H030.00
NI.23600.029
Lan Intel WLAN 512AN_HMWG Shirley Peak 5100
MM#895373
KI.SPH01.003
Lan Intel WLAN 512AN_MMWG Shirley Peak 5100
MM#895361
KI.SPM01.003
Lan Intel WLAN 533AN_HMWG Shirley Peak MM#895401
KI.SPH01.001
Lan Intel WLAN 533AN_MMWG Shirley Peak MM#895362
KI.SPM01.001
Battery
Board
Chapter 6
TOUCHPAD BOARD W/O FP
55.AS307.001
TOUCHPAD BOARD W/ FP
55.AR907.001
POWER BOARD
55.AR907.002
SWITCH BOARD
55.AR907.003
EMPOWER BOARD
55.AR907.004
163
Category
Description
Part Number
NEWCARD BOARD
55.TPK07.004
MSI VGA Card nVidia NB9P-GS DDRIII 512M 800MHz
32*32 MXM II w/ HDCP w/ Intersil PowerIC
VG.9PG06.002
MSI VGA Card nVidia NB9M-GS DDRII 256M 400MHz
32*16 MXM I w/ HDCP w/ Intersil PowerIC
VG.9MG06.001
DVB-T MINI TUNER CARD A310 W/CONN & ADA
TU.23100.010
INVERTER BOARD
19.TPK07.001
PWR CORD V943B30001218008 DANISH 3P
27.A03V7.006
PWR CORD (ISR) 1.8M 3PBLK FZ0I0008-038
27.TATV7.005
PWR CORD V50CB3T3012180QD TW-110V,3P
27.A99V7.002
POWER CORD (SWI) 1.8M 3PBLACK FZ010008-011
27.A99V7.004
Cables
164
POWER CORD (IT) 1.8M 3PBLACK FZ010008-008
27.A99V7.005
POWER CORD (S.A) 1.8M 3BLACK FZ010008-006
27.T48V7.001
POWER CORD US 3PIN ROHS
27.TAXV7.001
POWER CORD (EU) 1.8M 3PBLACK FM010008-010
27.TATV7.001
POWER CORD (UK) 1.8M 3PBLACK FP010008-013
27.TATV7.003
BLUETOOTH CABLE
50.TPK07.001
NEW CARD CABLE
50.TPK07.002
FFC CABLE - POWER/B TO MB
50.AR907.001
LCD CABLE FOR CCD
50.AR907.002
Chapter 6
Category
Description
Part Number
Assembly Parts
MIDDLE COVER
Chapter 6
42.AR907.001
UPPER CASE W/SPEAKER, FFC, CABLE,TP FOR NON-FP
60.AS307.001
UPPER CASE W/SPEAKER, FFC, CABLE,TP FOR FP
60.AR907.001
LOWER CASE ASSY W/SUB-WOOF,RJ11 W/O TV
60.AR907.002
LOWER CASE ASSY W/SUB-WOOF,RJ11,TV OUT CABLE
60.AS307.002
RAM COVER
42.AR907.002
HDD COVER -1
42.AR907.003
HDD COVER - 2ND
42.AR907.004
DDR BRACKET
33.AR907.001
TP BRACKET
33.AR907.002
ODD CAP
42.AR907.007
VGA SUPPORT BRACKET
33.AHS07.007
MIDDLE COVER TEXTURE
TBD
UPPER CASE TEXTURE W/SPEAKER, FFC, CABLE,TP
FOR NON-FP
TBD
LOWER CASE ASSY W/SUB-WOOF,RJ11 W/O TV HDMI
TBD
OPTICAL BRACKET
33.AR907.003
DVD/CDRW COMBO BEZEL
42.AR907.005
OPTICAL BRACKET
33.AR907.003
ODD BEZEL - SUPER MULTI
42.AGW07.004
OPTICAL BRACKET
33.AR907.003
BD COMBO BEZEL
42.AR907.006
HDD MASTER BRACKET
33.AR907.005
HDD BRACKET ASSY
33.AR907.004
HDD CONNECTOR
20.AR907.001
165
Category
Description
Part Number
LCD BEZEL TEXTURE FOR CCD
LCD COVER HOLO 3D MIMO W/ 3 ANTENNA
60.AR907.004
LCD BEZEL PAINTING FOR CCD
60.AR907.005
LCD BRACKET W/HINGE - R
33.AR907.006
LCD BRACKET W/HINGE - L
33.AR907.007
LCD COVER ASSY W/MIC W/ANTENNA
LCD COVER HOLO 3D W/ 2 ANTENNA
60.AR907.006
CAMERA CN0314-SN30-OV03 SUYIN
57.TPK07.001
CAMERA CNF701721004971L CNY
57.TPK07.002
CPU Intel Core2Dual T9600 PGA 2.8G 6M 1066 35W
KC.96001.DTP
CPU Intel Core2Dual T9400 PGA 2.53G 6M 1066 35W
KC.94001.DTP
CPU Intel Core2Dual P8600 PGA 2.4G 1066 25W 3M
KC.86001.DPP
CPU Intel Core2Dual P8400 PGA 2.26G 3M 1066 25W
KC.84001.DPP
CPU Intel Core2Dual P9500 PGA 2.53G 6M 1066 25W
KC.95001.DPP
DVD/CDRW COMBO MODULE
6M.AR907.001
TOSHIBA COMBO Tray DL 24X TS-L463A LF W/O bezel
SATA
KO.02401.006
SONY COMBO Tray DL 24X CRX890S LF W/O bezel SATA
KO.0240E.009
BLUE RAY COMBO TRAY 2X SONY BC-5500S-AR
KO.0020E.002
DVD/RW SUPER MULTI MODULE
6M.AR907.002
TOSHIBA Super-Multi DRIVE Tray DL 8X TS-L633A LF W/O
bezel SATA
KU.00801.021
PIONEER Super-Multi DRIVE Tray DL 8X DVR-TD08RS LF
W/O bezel SATA
KU.00805.044
HLDS Super-Multi DRIVE Tray DL 8X GSA-T50N LF W/O
bezel SATA Malaysia
TBD
ODD HLDS Super-Multi DRIVE 12.7mm Tray DL 8X GSAT50N LF W/O bezel SATA FW:RP05
KU.0080D.029
ODD HLDS Super-Multi DRIVE 12.7mm Tray DL 8X GSAT50N LF W/O bezel SATA Malaysia FW:RP05
KU.0080D.034
BLUE RAY COMBO MODULE
6M.AR907.003
CCD
CPU/PROCESSOR
Combo Drive
DVD RW DRIVE
166
Chapter 6
Category
Description
Part Number
Hard Disk
HDD TOSHIBA 5400rpm 120GB MK1246GSX Leo BS SATA
I LF F/W:LB213J
KH.12004.007
HDD WD 5400rpm 120GB WD1200BEVS-22UST0 ML125
SATA LF F/W:01.01A01
KH.12008.019
HDD TOSHIBA 5400rpm 160GB MK1646GSX Leo BS SATA
I LF F/W:LB113J
KH.16004.002
HDD WD 2.5" 5400rpm 160GB WD1600BEVT-22ZCTO
ML160 SATA LF F/W:11.01A11
KH.16008.022
HDD SEAGATE 2.5" 5400rpm 250GB ST9250827AS Corsair
SATA LF F/W:3.AAA
KH.25001.011
HDD TOSHIBA 2.5" 5400rpm 320GB MK3252GSX Virgo BS
SATA LF F/W:LV010J
KH.32004.001
THERMAL MODULE - UMA
60.AQF07.001
THERMAL MODULE - DIS
60.AR907.003
Keyboard 17KB-FV3 Black Mammoth 105KS Black US
International Hebrew
KB.INT00.478
Keyboard 17KB-FV3 Black Mammoth 105KS Black US
International
KB.INT00.478
Keyboard 17KB-FV3 Black Mammoth 106KS Black UK
KB.INT00.480
Heatsink
Keyboard
Chapter 6
Keyboard 17KB-FV3 Black Mammoth 106KS Black Turkish
KB.INT00.481
Keyboard 17KB-FV3 Black Mammoth 105KS Black Thailand
KB.INT00.482
Keyboard 17KB-FV3 Black Mammoth 106KS Black Swiss/G
KB.INT00.483
Keyboard 17KB-FV3 Black Mammoth 106KS Black Swedish
KB.INT00.484
Keyboard 17KB-FV3 Black Mammoth 106KS Black Spanish
KB.INT00.485
Keyboard 17KB-FV3 Black Mammoth 106KS Black Slovak
KB.INT00.486
Keyboard 17KB-FV3 Black Mammoth 106KS Black SLO/
CRO
KB.INT00.487
Keyboard 17KB-FV3 Black Mammoth 105KS Black Russian
KB.INT00.488
Keyboard 17KB-FV3 Black Mammoth 106KS Black
Portuguese
KB.INT00.489
Keyboard 17KB-FV3 Black Mammoth 106KS Black Polish
KB.INT00.490
Keyboard 17KB-FV3 Black Mammoth 106KS Black
Norwegian
KB.INT00.491
Keyboard 17KB-FV3 Black Mammoth 105KS Black Korean
KB.INT00.493
Keyboard 17KB-FV3 Black Mammoth 106KS Black Italian
KB.INT00.494
Keyboard 17KB-FV3 Black Mammoth 106KS Black
Hungarian
KB.INT00.497
Keyboard 17KB-FV3 Black Mammoth 105KS Black Greek
KB.INT00.498
Keyboard 17KB-FV3 Black Mammoth 106KS Black German
KB.INT00.499
Keyboard 17KB-FV3 Black Mammoth 106KS Black French
KB.INT00.500
Keyboard 17KB-FV3 Black Mammoth 106KS Black Danish
KB.INT00.503
Keyboard 17KB-FV3 Black Mammoth 106KS Black Czech
KB.INT00.504
167
Category
Description
Part Number
Keyboard 17KB-FV3 Black Mammoth 105KS Black
Traditional Chinese
KB.INT00.505
Keyboard 17KB-FV3 Black Mammoth 106KS Black
Canadian French
KB.INT00.506
Keyboard 17KB-FV3 Black Mammoth 106KS Black Brazilian
Portuguese
KB.INT00.507
Keyboard 17KB-FV3 Black Mammoth 106KS Black Belgium
KB.INT00.508
Keyboard 17KB-FV3 Black Mammoth 105KS Black Arabic/
English
KB.INT00.509
Keyboard 17KB-FV3 Black Mammoth 106KS Black Nordic
KB.INT00.511
LCD MODULE ASSY17.1 WXGA+G HOLO 3D 3 ANTENNA
W/CCD
6M.AR907.004
LCD AUO 17.1" WXGA+ Glare B170PW06 V2 LF 220nit 8ms
LK.17105.009
LCD SAMSUNG 17.1" WXGA+ Glare LTN170BT07-G01 LF
220nit 8ms 500:1
LK.17106.004
LCD LPL 17.1" WXGA+ Glare LP171WP4-TLR1 LF 220nit
8ms
LK.17108.011
LCD MODULE ASSY17.1 WXGA+G HOLO 3D 2 ANTENNA
W/CCD
6M.AR907.005
MAINBOARD DIS PM45 ICH9 DDRIII GL W/CARD
READER W/O CPU RAM
MB.ARC06.001
MAINBOARD UMA GM45 ICH9 DDRII GL W/CARD
READER W/O CPU RAM
MB.AQF06.001
SO-DIMM DDRII 667 NANYA 1GB NT1GT64U8HB0BN-3C
(0.09U)
KN.1GB03.014
Memory HYNIX SO-DIMM DDRII 667 1GB
HYMP112S64CP6-Y5 LF
KN.1GB0G.012
SO-DIMM DDRII667 512MB NT512T64UH8B0FN-37C
(0.09U)\'NANYA
KN.51203.032
Memory MICRON SO-DIMM DDRII 667 2GB
MT16HTF25664HY-667E1 LF
KN.2GB04.001
Memory SAMSUNG SO-DIMM DDRII 667 2GB
M470T5663QZ3-CE6 LF
KN.2GB0B.003
Memory SAMSUNG SO-DIMM DDRIII 1066 1GB
M471B2874DZ1-CF8 LF
KN.1GB0B.019
Memory SAMSUNG SO-DIMM DDRIII 1066 2GB
M471B5673DZ1-CF8 LF
KN.2GB0B.005
Memory MICRON SO-DIMM DDRIII 1066 1GB
MT8JSF12864HY-1G1D1 LF 64*16 0.07um
KN.1GB04.003
Memory MICRON SO-DIMM DDRIII 1066 2GB
MT16JSF25664HY-1G1D1 LF 128*8 0.07um
KN.2GB04.004
HDD SEAGATE 2.5" 5400rpm 120GB ST9120817AS Corsair
SATA LF F/W:3.AAA
KH.12001.032
LCD Panel
Mainboard
Memory
SATA HDD/HARD DISK DRIVE
168
Chapter 6
Category
Description
Part Number
HDD(160G) ST9160827AS 9DG133-188 STN B/S
SEAGATE F/W:3.AAA
KH.16001.029
HDD HGST 2.5" 5400rpm 160GB HTS542516K9SA00
Bronco-B SATA II LF F/W:C31P
KH.16007.016
HDD TOSHIBA 2.5" 5400rpm 250GB MK2546GSX Leo BS
SATA I LF F/W:LB013J
KH.25004.001
HDD WD 2.5 IN. 5400rpm 250GB WD2500BEVS-22UST0
ML125 SATA LF F/W:01.01A01
KH.25008.018
HDD WD 2.5" 5400rpm 320GB WD3200BEVT-22ZCT0
ML160 SATA LF F/W:11.01A11
KH.32008.013
HDD 250GB 5400RPM SATA II HGST HTS542525K9SA00
LF F/W:C31P
KH.25007.011
HDD HGST 2.5" 5400rpm 500GB HTS545050KTA300
Bronco K SATA LF F/W:C60G
KH.50007.007
SPEAKER
23.AR907.001
NAME PLATE AS7730
40.AR907.001
LCD GLOSS RUBBER PAD
47.AR907.002
Speaker
Accessory
Miscellaneous
RUBBER FOOT
47.AR907.003
RUBBER FOOT LOW
47.AR907.004
Screw List
Category
Description
Part Number
Screw List
Chapter 6
SCREW
SCREW M2.5*6.5-I(BZN (NYLOK-RED)
86.ARE07.001
SCREW
SCREW M2.0*3.0-I(BKAG)(NYLOK IRON
86.ARE07.002
SCREW
SCWER M2.5*3.0-I(BNI)(NYLOK)
86.T25V7.012
SCREW
SCREW M2.0*3.0-I-NI-NYLOK
86.A08V7.005
SCREW
SCREW M2.0*2-I(BNI)(NYLOK)IRON
86.AR907.001
SCREW
SCREW M3.0*3.0-I(BZN)(NYLOK)IRON
86.AR907.002
169
Appendix A
Model Definition and Configuration
Aspire 7730/7730G Series
Model
RO
Country
Acer
Part
no
Descriptio
n
CPU
LCD
DIMM
1
DIMM
2
HDD 1
(GB)
ODD
Wirele
ss
LAN
Blueto
oth
VOIP
Phone
AS505
1ANW
XMi
AAP
India
LX.AV
30C.0
02
AS5051AN
WXMi
LINPUSIL1
UMAC
1*512/80/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N80G
B5.4K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1ANW
XMi
AAP
Indonesia
LX.AV
30C.0
03
AS5051AN
WXMi
LINPUSIN1
UMAC
1*512/80/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N80G
B5.4K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1ANW
XMi
AAP
Malaysia
LX.AV
30C.0
05
AS5051AN
WXMi
LINPUSMA
2 UMAC
1*512/80/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N80G
B5.4K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1ANW
XMi
AAP
Philippines
LX.AV
30C.0
04
AS5051AN
WXMi
LINPUSPH
1 UMAC
1*512/80/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N80G
B5.4K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1ANW
XMi
AAP
Singapore
LX.AV
30C.0
01
AS5051AN
WXMi
LINPUSSG
1 UMAC
1*512/80/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N80G
B5.4K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1ANW
XMi
AAP
Thailand
LX.AV
30C.0
06
AS5051AN
WXMi
LINPUSTH
2 UMAC
1*512/80/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N80G
B5.4K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1ANW
XMi
AAP
Vietnam
LX.AV
30C.0
07
AS5051AN
WXMi
LINPUSVN
1 UMAC
1*512/80/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N80G
B5.4K
NSM8
X
ABT_
ATH54
13BG
N
N
Appendix A
170
Model
171
RO
Country
Acer
Part
no
Descriptio
n
CPU
LCD
DIMM
1
DIMM
2
HDD 1
(GB)
ODD
Wirele
ss
LAN
Blueto
oth
VOIP
Phone
AS505
1AWX
Mi
PA
USA/
Canada Canadian
French
LX.AV
30J.00
1
AS5051AW
XMi
MCECF
UMAC
2*512/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1AWX
Mi
PA
USA/
Canada Canadian
French
LX.AV
30J.00
2
AS5051AW
XMi
MCEUS
UMAC
2*512/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1AWX
Mi
AAP
Australia/
New
Zealand
LX.AV
305.00
1
AS5051AW
XMi
XPHAU1
UMAC
1*512/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1AWX
Mi
PA
USA/
Canada
LX.AV
305.00
8
AS5051AW
XMi
XPHEN1
UMAC
1*512/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1AWX
Mi
PA
ACLASpanish
LX.AV
305.01
0
AS5051AW
XMi
XPHES1
UMAC
1*512/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1AWX
Mi
PA
USA/
Canada
LX.AV
305.00
9
AS5051AW
XMi
XPHFR1
UMAC
1*512/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1AWX
Mi
AAP
Indonesia
LX.AV
305.00
7
AS5051AW
XMi
XPHIN1
UMAC
1*512/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1AWX
Mi
AAP
Malaysia
LX.AV
305.00
3
AS5051AW
XMi
XPHMA2
UMAC
1*512/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1AWX
Mi
AAP
Philippines
LX.AV
305.00
2
AS5051AW
XMi
XPHPH1
UMAC
1*512/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
Appendix A
Model
RO
Country
Acer
Part
no
Descriptio
n
CPU
LCD
DIMM
1
DIMM
2
HDD 1
(GB)
ODD
Wirele
ss
LAN
Blueto
oth
VOIP
Phone
AS505
1AWX
Mi
AAP
Thailand
LX.AV
305.00
4
AS5051AW
XMi
XPHTH2
UMAC
1*512/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1AWX
Mi
AAP
Vietnam
LX.AV
305.00
5
AS5051AW
XMi
XPHVN1
UMAC
1*512/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1AWX
Mi
AAP
Singapore
LX.AV
305.00
6
AS5051AW
XMi
XPHWSG2
1W UMAC
1*512/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1AWX
Mi
PA
ACLAPortuguese
LX.AV
305.01
1
AS5051AW
XMi
XPHXC1
UMAC
1*512/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1AWX
Mi
TWN
GCTWN
S2.AV
305.00
1
AS5051AW
XMi
XPHTC1
UMAC
2*512/120/
BT/6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII6
SO512
MBII6
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
FOX_
BRM_
2.0
N
AS505
2WXM
i
TWN
GCTWN
S2.AV
305.00
2
AS5052WX
Mi
XPHTC1
UMAC
2*512/100/
BT/6L/5R/
CB_bg_0.3
C_AN
ATTL5
0
N14.1
WXGA
G
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
FOX_
BRM_
2.0
N
AS505
5WXM
i
TWN
GCTWN
S2.AV
305.00
3
AS5055WX
Mi
XPHTC1
UMAC
2*1G/160/
BT/6L/5R/
CB_bg_0.3
C_AN
ATTL6
0
N14.1
WXGA
G
SO1G
BII5
SO1G
BII5
N160
GB5.4
KS
NSM8
X
ABT_
BRM4
318BG
FOX_
BRM_
2.0
N
AS505
1AWX
Ci
China
Hong Kong
LX.AV
305.01
6
AS5051AW
XCi
XPHHK9
UMAC
1*512/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N120
GB5.4
K
NCB2
4X
ABT_
ATH54
13BG
N
N
AS505
1AWX
Ci
China
China
LX.AV
305.01
5
AS5051AW
XCi
XPHSC7
UMAC
1*512/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N120
GB5.4
K
NCB2
4X
ABT_
ATH54
13BG
N
N
Appendix A
172
Model
173
RO
Country
Acer
Part
no
Descriptio
n
CPU
LCD
DIMM
1
DIMM
2
HDD 1
(GB)
ODD
Wirele
ss
LAN
Blueto
oth
VOIP
Phone
AS505
1AWX
Mi
TWN
GCTWN
LX.AV
305.01
2
AS5051AW
XMi
XPHTC1
UMAC
1*512/120/
BT/6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
FOX_
BRM_
2.0
N
AS505
1AWX
Mi
TWN
GCTWN
LX.AV
305.01
4
AS5051AW
XMi
XPHTC1
UMAC
1*512/60/
BT/6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N60G
B5.4K
NSM8
X
ABT_
ATH54
13BG
FOX_
BRM_
2.0
N
AS505
1AWX
Mi
TWN
GCTWN
LX.AV
305.01
3
AS5051AW
XMi
XPHTC1
UMAC
1*512/80/
BT/6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N80G
B5.4K
NSM8
X
ABT_
ATH54
13BG
FOX_
BRM_
2.0
N
AS505
1AWX
Mi
AAP
Australia/
New
Zealand
LX.AV
30J.01
1
AS5051AW
XMi
MCEAU1
UMAC
1*1G/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO1G
BII6
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1AWX
Mi
AAP
Singapore
LX.AV
30J.01
2
AS5051AW
XMi
MCESG1
UMAC
1*1G/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO1G
BII6
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1AWX
Mi
AAP
India
LX.AV
30J.01
3
AS5051AW
XMi
MCEIL1
UMAC
1*1G/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO1G
BII6
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1AWX
Mi
AAP
Indonesia
LX.AV
30J.01
4
AS5051AW
XMi
MCEIN1
UMAC
1*1G/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO1G
BII6
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1AWX
Mi
AAP
Philippines
LX.AV
30J.01
5
AS5051AW
XMi
MCEPH1
UMAC
1*1G/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO1G
BII6
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1AWX
Mi
AAP
Malaysia
LX.AV
30J.01
6
AS5051AW
XMi
MCEMA1
UMAC
1*1G/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO1G
BII6
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
Appendix A
Model
RO
Country
Acer
Part
no
Descriptio
n
CPU
LCD
DIMM
1
DIMM
2
HDD 1
(GB)
ODD
Wirele
ss
LAN
Blueto
oth
VOIP
Phone
AS505
1AWX
Mi
AAP
Thailand
LX.AV
30J.01
7
AS5051AW
XMi
MCETH1
UMAC
1*1G/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO1G
BII6
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1AWX
Mi
AAP
Vietnam
LX.AV
30J.01
8
AS5051AW
XMi
MCEVN1
UMAC
1*1G/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO1G
BII6
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1AWX
Mi
AAP
Australia/
New
Zealand
LX.AV
306.00
2
AS5051AW
XMi
XPPAU1
UMAC
1*1G/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO1G
BII6
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
2WXM
i
AAP
Australia/
New
Zealand
LX.AV
30J.00
3
AS5052WX
Mi
MCEAU1
UMAC
1*1G/120/
6L/5R/
CB_bg_0.3
C_AN
ATTL5
0
N14.1
WXGA
G
SO1G
BII6
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
2WXM
i
AAP
India
LX.AV
30J.00
5
AS5052WX
Mi MCEIL1
UMAC
1*1G/120/
6L/5R/
CB_bg_0.3
C_AN
ATTL5
0
N14.1
WXGA
G
SO1G
BII6
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
2WXM
i
AAP
Indonesia
LX.AV
30J.00
6
AS5052WX
Mi MCEIN1
UMAC
1*1G/120/
6L/5R/
CB_bg_0.3
C_AN
ATTL5
0
N14.1
WXGA
G
SO1G
BII6
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
2WXM
i
AAP
Singapore
LX.AV
30J.00
4
AS5052WX
Mi
MCESG1
UMAC
1*1G/120/
6L/5R/
CB_bg_0.3
C_AN
ATTL5
0
N14.1
WXGA
G
SO1G
BII6
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
2WXM
i
AAP
Philippines
LX.AV
30J.00
7
AS5052WX
Mi
MCEPH1
UMAC
1*1G/120/
6L/5R/
CB_bg_0.3
C_AN
ATTL5
0
N14.1
WXGA
G
SO1G
BII6
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
2WXM
i
AAP
Malaysia
LX.AV
30J.00
8
AS5052WX
Mi
MCEMA1
UMAC
1*1G/120/
6L/5R/
CB_bg_0.3
C_AN
ATTL5
0
N14.1
WXGA
G
SO1G
BII6
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
Appendix A
174
Model
175
RO
Country
Acer
Part
no
Descriptio
n
CPU
LCD
DIMM
1
DIMM
2
HDD 1
(GB)
ODD
Wirele
ss
LAN
Blueto
oth
VOIP
Phone
AS505
2WXM
i
AAP
Thailand
LX.AV
30J.00
9
AS5052WX
Mi
MCETH1
UMAC
1*1G/120/
6L/5R/
CB_bg_0.3
C_AN
ATTL5
0
N14.1
WXGA
G
SO1G
BII6
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
2WXM
i
AAP
Vietnam
LX.AV
30J.01
0
AS5052WX
Mi
MCEVN1
UMAC
1*1G/120/
6L/5R/
CB_bg_0.3
C_AN
ATTL5
0
N14.1
WXGA
G
SO1G
BII6
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
2WXM
i
AAP
Australia/
New
Zealand
LX.AV
306.00
1
AS5052WX
Mi XPPAU1
UMAC
1*1G/120/
6L/5R/
CB_bg_0.3
C_AN
ATTL5
0
N14.1
WXGA
G
SO1G
BII6
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1ANW
XMi
AAP
India
LX.AV
30C.0
15
AS5051AN
WXMi
LINPUSIL1
UMAC
1*256/60/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO256
MBII5
N
N60G
B5.4K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1ANW
XMi
AAP
Vietnam
LX.AV
30C.0
14
AS5051AN
WXMi
LINPUSVN
1 UMAC
1*512/60/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N60G
B5.4K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1ANW
XMi
AAP
Thailand
LX.AV
30C.0
16
AS5051AN
WXMi
LINPUSTH
2 UMAC
1*512/80/
BT/6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N80G
B5.4K
NSM8
X
ABT_
ATH54
13BG
FOX_
BRM_
2.0
N
AS505
1ANW
XMi
AAP
Singapore
LX.AV
30C.0
08
AS5051AN
WXMi
LINPUSSG
1 UMAC
1*512/60/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N60G
B5.4K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1ANW
XMi
AAP
India
LX.AV
30C.0
09
AS5051AN
WXMi
LINPUSIL1
UMAC
1*512/60/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N60G
B5.4K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1ANW
XMi
AAP
Indonesia
LX.AV
30C.0
10
AS5051AN
WXMi
LINPUSIN1
UMAC
1*512/60/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N60G
B5.4K
NSM8
X
ABT_
ATH54
13BG
N
N
Appendix A
Model
RO
Country
Acer
Part
no
Descriptio
n
CPU
LCD
DIMM
1
DIMM
2
HDD 1
(GB)
ODD
Wirele
ss
LAN
Blueto
oth
VOIP
Phone
AS505
1ANW
XMi
AAP
Philippines
LX.AV
30C.0
11
AS5051AN
WXMi
LINPUSPH
1 UMAC
1*512/60/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N60G
B5.4K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1ANW
XMi
AAP
Malaysia
LX.AV
30C.0
12
AS5051AN
WXMi
LINPUSMA
2 UMAC
1*512/60/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N60G
B5.4K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1ANW
XMi
AAP
Thailand
LX.AV
30C.0
13
AS5051AN
WXMi
LINPUSTH
2 UMAC
1*512/60/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N60G
B5.4K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
2WXM
i
AAP
Thailand
LX.AV
30J.01
9
AS5052WX
Mi
MCETH1
UMAC
1*1G/120/
BT/6L/5R/
CB_bg_0.3
C_AN
ATTL5
0
N14.1
WXGA
G
SO1G
BII6
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
FOX_
BRM_
2.0
N
AS505
1AWX
Mi
EMEA
Belgium
LX.AV
30J.03
2
AS5051AW
XMi
MCEBE6
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS505
1AWX
Mi
EMEA
Middle
East
LX.AV
30J.04
3
AS5051AW
XMi
MCEAR1
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS505
1AWX
Mi
EMEA
Middle
East
LX.AV
30J.04
4
AS5051AW
XMi
MCEAR2
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS505
1AWX
Mi
EMEA
Italy
LX.AV
30J.04
0
AS5051AW
XMi
MCEIT7
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS505
1AWX
Mi
EMEA
Spain
LX.AV
30J.03
9
AS5051AW
XMi
MCEESJ
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
Appendix A
176
177
Acer
Part
no
CPU
LCD
DIMM
1
DIMM
2
HDD 1
(GB)
AS5051AW
XMi
MCECS5
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
LX.AV
30J.02
4
AS5051AW
XMi
MCEDK6
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
France
LX.AV
30J.02
5
AS5051AW
XMi
MCEFRF
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
EMEA
Germany
LX.AV
30J.02
7
AS5051AW
XMi
MCEDEA
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
AS505
1AWX
Mi
EMEA
Germany
LX.AV
30J.02
8
AS5051AW
XMi
MCEDEB
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
AS505
1AWX
Mi
EMEA
Holland
LX.AV
30J.03
3
AS5051AW
XMi
MCENL6
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
AS505
1AWX
Mi
EMEA
Norway
LX.AV
30J.03
4
AS5051AW
XMi
MCENO5
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
AS505
1AWX
Mi
EMEA
Russia
LX.AV
30J.03
5
AS505
1AWX
Mi
EMEA
Eastern
Europe
LX.AV
30J.03
6
Model
RO
Country
AS505
1AWX
Mi
EMEA
Eastern
Europe
LX.AV
30J.03
0
AS505
1AWX
Mi
EMEA
Denmark
AS505
1AWX
Mi
EMEA
AS505
1AWX
Mi
Descriptio
n
Wirele
ss
LAN
Blueto
oth
VOIP
Phone
ABT_
BRM4
318BG
N
N
NSM8
X
ABT_
BRM4
318BG
N
N
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS5051AW
XMi
MCERU9
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS5051AW
XMi
MCEPL7
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
ODD
Appendix A
Acer
Part
no
CPU
LCD
DIMM
1
DIMM
2
HDD 1
(GB)
AS5051AW
XMi
MCESI1
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
LX.AV
30J.03
8
AS5051AW
XMi
MCEPT6
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
Sweden/
Finland
LX.AV
30J.02
9
AS5051AW
XMi
MCESV5
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
EMEA
Turkey
LX.AV
30J.04
1
AS5051AW
XMi
MCETR5
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
AS505
1AWX
Mi
EMEA
Switzerland
LX.AV
30J.04
5
AS5051AW
XMi
MCESW8
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
AS505
1AWX
Mi
EMEA
UK
LX.AV
30J.04
6
AS5051AW
XMi
MCEUK5
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
AS505
1AWX
Mi
EMEA
UK
LX.AV
30J.04
7
AS5051AW
XMi
MCEWUK1
1W UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
AS505
1AWX
Mi
EMEA
Italy
LX.AV
30J.04
2
AS505
1AWX
Mi
EMEA
Germany
LX.AV
30J.03
1
Model
RO
AS505
1AWX
Mi
EMEA
Slovenia/
Croatia
LX.AV
30J.03
7
AS505
1AWX
Mi
EMEA
Portugal
AS505
1AWX
Mi
EMEA
AS505
1AWX
Mi
Appendix A
Country
Descriptio
n
Wirele
ss
LAN
Blueto
oth
VOIP
Phone
ABT_
BRM4
318BG
N
N
NSM8
X
ABT_
BRM4
318BG
N
N
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS5051AW
XMi
MCEWIT11
W UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS5051AW
XMi
MCEWDE1
1W UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
ODD
178
179
Acer
Part
no
CPU
LCD
DIMM
1
DIMM
2
HDD 1
(GB)
AS5051AW
XMi
MCEWFR1
1W UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
LX.AV
305.01
9
AS5051AW
XMi
XPHBE1
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
Middle
East
LX.AV
305.03
8
AS5051AW
XMi
XPHAR1
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
EMEA
Eastern
Europe
LX.AV
305.02
7
AS5051AW
XMi
XPHCS2
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
AS505
1AWX
Mi
EMEA
Germany
LX.AV
305.02
3
AS5051AW
XMi
XPHDE7
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
AS505
1AWX
Mi
EMEA
Greece
LX.AV
305.03
3
AS5051AW
XMi
XPHEL1
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
AS505
1AWX
Mi
EMEA
Israel
LX.AV
305.03
4
AS5051AW
XMi
XPHIS1
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
AS505
1AWX
Mi
EMEA
Italy
LX.AV
305.03
5
AS505
1AWX
Mi
EMEA
Denmark
LX.AV
305.01
8
Model
RO
Country
AS505
1AWX
Mi
EMEA
France
LX.AV
30J.02
6
AS505
1AWX
Mi
EMEA
Belgium
AS505
1AWX
Mi
EMEA
AS505
1AWX
Mi
Descriptio
n
Wirele
ss
LAN
Blueto
oth
VOIP
Phone
ABT_
BRM4
318BG
N
N
NSM8
X
ABT_
BRM4
318BG
N
N
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS5051AW
XMi
XPHIT1
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS5051AW
XMi
XPHDK1
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
ODD
Appendix A
Acer
Part
no
CPU
LCD
DIMM
1
DIMM
2
HDD 1
(GB)
AS5051AW
XMi
XPHNL1
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
LX.AV
305.02
1
AS5051AW
XMi
XPHFRA
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
Eastern
Europe
LX.AV
305.02
8
AS5051AW
XMi
XPHHU6
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
EMEA
Spain
LX.AV
305.03
1
AS5051AW
XMi
XPHESA
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
AS505
1AWX
Mi
EMEA
Slovenia/
Croatia
LX.AV
305.03
0
AS5051AW
XMi
XPHSLO2
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
AS505
1AWX
Mi
EMEA
Eastern
Europe
LX.AV
305.02
9
AS5051AW
XMi
XPHPL6
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
AS505
1AWX
Mi
EMEA
Portugal
LX.AV
305.03
2
AS5051AW
XMi
XPHPT1
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
AS505
1AWX
Mi
EMEA
Switzerland
LX.AV
305.03
9
AS505
1AWX
Mi
EMEA
Turkey
LX.AV
305.03
6
Model
RO
AS505
1AWX
Mi
EMEA
Holland
LX.AV
305.02
0
AS505
1AWX
Mi
EMEA
France
AS505
1AWX
Mi
EMEA
AS505
1AWX
Mi
Appendix A
Country
Descriptio
n
Wirele
ss
LAN
Blueto
oth
VOIP
Phone
ABT_
BRM4
318BG
N
N
NSM8
X
ABT_
BRM4
318BG
N
N
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS5051AW
XMi
XPHSW5
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS5051AW
XMi
XPHTR1
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
ODD
180
181
Acer
Part
no
CPU
LCD
DIMM
1
DIMM
2
HDD 1
(GB)
AS5051AW
XMi
XPHSA1
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
LX.AV
305.02
4
AS5051AW
XMi
XPHNO1
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
Russia
LX.AV
305.02
5
AS5051AW
XMi
XPHRU2
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
EMEA
Sweden/
Finland
LX.AV
305.02
6
AS5051AW
XMi
XPHSV1
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
AS505
1AWX
Mi
EMEA
France
LX.AV
305.02
2
AS5051AW
XMi
XPHWFRB
1W UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
AS505
1AWX
Mi
EMEA
Italy
LX.AV
305.03
7
AS5051AW
XMi
XPHWIT21
W UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
AS505
1AWX
Mi
EMEA
UK
LX.AV
305.04
0
AS5051AW
XMi
XPHUK1
UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
AS505
1AWX
Mi
EMEA
UK
LX.AV
305.04
1
AS505
2WXM
i
PA
USA/
Canada Canadian
French
LX.AV
30J.02
0
Model
RO
Country
AS505
1AWX
Mi
EMEA
South
Africa
LX.AV
305.01
7
AS505
1AWX
Mi
EMEA
Norway
AS505
1AWX
Mi
EMEA
AS505
1AWX
Mi
Descriptio
n
Wirele
ss
LAN
Blueto
oth
VOIP
Phone
ABT_
BRM4
318BG
N
N
NSM8
X
ABT_
BRM4
318BG
N
N
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS5051AW
XMi
XPHWUK2
1W UMAC
2*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
SO512
MBII6
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS5052WX
Mi MCECF
UMAC
2*512/120/
6L/5R/
CB_bg_0.3
C_AN
ATTL5
0
N14.1
WXGA
G
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
ODD
Appendix A
Model
RO
Country
Acer
Part
no
Descriptio
n
CPU
LCD
DIMM
1
DIMM
2
HDD 1
(GB)
ODD
Wirele
ss
LAN
Blueto
oth
VOIP
Phone
AS505
2WXM
i
PA
USA/
Canada Canadian
French
LX.AV
30J.02
1
AS5052WX
Mi MCEUS
UMAC
2*512/120/
6L/5R/
CB_bg_0.3
C_AN
ATTL5
0
N14.1
WXGA
G
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
2WXM
i
PA
ACLASpanish
LX.AV
30J.02
2
AS5052WX
Mi
MCEES1
UMAC
2*512/120/
6L/5R/
CB_bg_0.3
C_AN
ATTL5
0
N14.1
WXGA
G
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
N
N
AS505
1AWX
Mi
PA
ACLASpanish
LX.AV
30J.04
8
AS5051AW
XMi
MCEES1
UMAC
2*512/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS505
1ANW
XCi
AAP
Australia/
New
Zealand
LX.AV
30C.0
17
AS5051AN
WXCi
LINPUSAU
1 UMAC
1*512/80/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N80G
B5.4K
NCB2
4X
ABT_
BRM4
318BG
N
N
AS505
1AWX
Ci
AAP
Malaysia
LX.AV
305.04
2
AS5051AW
XCi
XPHMA2
UMAC
1*512/80/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N80G
B5.4K
NCB2
4X
ABT_
BRM4
318BG
N
N
AS505
1ANW
XCi
AAP
Malaysia
LX.AV
30C.0
18
AS5051AN
WXCi
LINPUSMA
2 UMAC
1*512/80/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N80G
B5.4K
NCB2
4X
ABT_
BRM4
318BG
N
N
AS505
1AWX
Mi
EMEA
Sweden/
Finland
LX.AV
30J.04
9
AS5051AW
XMi
MCESV5
UMAC
1*512/100/
BT/6L/5R/
CB_bg_VP
_0.3C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII6
N
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
FOX_
BRM_
2.0
BT
VoIP
PCMC
IA
AS505
1AWX
Mi
EMEA
Slovenia/
Croatia
LX.AV
30J.05
0
AS5051AW
XMi
MCESI1
UMAC
1*512/100/
BT/6L/5R/
CB_bg_VP
_0.3C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII6
N
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
FOX_
BRM_
2.0
BT
VoIP
PCMC
IA
AS505
1AWX
Mi
EMEA
Holland
LX.AV
30J.05
1
AS5051AW
XMi
MCENL6
UMAC
1*512/100/
BT/6L/5R/
CB_bg_VP
_0.3C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII6
N
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
FOX_
BRM_
2.0
BT
VoIP
PCMC
IA
Appendix A
182
183
Acer
Part
no
Wirele
ss
LAN
Blueto
oth
VOIP
Phone
NSM8
X
ABT_
BRM4
318BG
FOX_
BRM_
2.0
BT
VoIP
PCMC
IA
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
FOX_
BRM_
2.0
BT
VoIP
PCMC
IA
N
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII6
N
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
FOX_
BRM_
2.0
BT
VoIP
PCMC
IA
N14.1
WXGA
SO512
MBII6
N
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
FOX_
BRM_
2.0
BT
VoIP
PCMC
IA
ATTL5
0
N14.1
WXGA
G
SO512
MBII5
N
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
FOX_
BRM_
2.0
N
AS5053WX
Mi
MCETH1
UMAC
1*1G/120/
BT/6L/5R/
CB_bg_0.3
C_AN
ATTL5
2
N14.1
WXGA
G
SO1G
BII6
N
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
FOX_
BRM_
2.0
N
LX.AV
30C.0
22
AS5051AN
WXMi
LINPUSAR
9 UMAC
1*512/60/
BT/6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
N
N60G
B5.4K
NSM8
X
ABT_
BRM4
318BG
FOX_
BRM_
2.0
N
LX.AV
30C.0
24
AS5051AN
WXMi
LINPUSAR
9 UMAC
1*512/60/
BT/6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N60G
B5.4K
NSM8
X
ABT_
BRM4
318BG
FOX_
BRM_
2.0
N
DIMM
1
DIMM
2
HDD 1
(GB)
N14.1
WXGA
G
SO512
MBII6
N
N100
GB5.4
K
ATMK
36
N14.1
WXGA
SO512
MBII6
N
AS5051AW
XMi
XPHRU2
UMAC
1*512/100/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII6
LX.AV
30J.05
5
AS5051AW
XMi
MCESV5
UMAC
1*512/100/
BT/6L/
5R_bg_VP
_0.3C_AN
ATMK
36
N14.1
WXGA
Slovenia/
Croatia
LX.AV
30J.05
3
AS5051AW
XMi
MCESI1
UMAC
1*512/100/
BT/6L/
5R_bg_VP
_0.3C_AN
ATMK
36
AAP
Thailand
LX.AV
30C.0
19
AS5052N
WXMi
LINPUSTH
2 UMAC
1*512/120/
BT/6L/5R/
CB_bg_0.3
C_AN
AS505
3WXM
i
AAP
Thailand
LX.AV
30J.05
6
AS505
1ANW
XMi
EMEA
Middle
East
AS505
1ANW
XMi
EMEA
Middle
East
Model
RO
Country
AS505
1AWX
Mi
EMEA
Russia
LX.AV
30J.05
2
AS505
1AWX
Mi
EMEA
Holland
AS505
1AWX
Mi
EMEA
AS505
1AWX
Mi
Descriptio
n
CPU
LCD
AS5051AW
XMi
MCERU9
UMAC
1*512/100/
BT/6L/5R/
CB_bg_VP
_0.3C_AN
ATMK
36
LX.AV
30J.05
4
AS5051AW
XMi
MCENL6
UMAC
1*512/100/
BT/6L/
5R_bg_VP
_0.3C_AN
Russia
LX.AV
305.04
3
EMEA
Sweden/
Finland
AS505
1AWX
Mi
EMEA
AS505
2NWX
Mi
ODD
Appendix A
Acer
Part
no
Wirele
ss
LAN
Blueto
oth
VOIP
Phone
NSM8
X
ABT_
BRM4
318BG
FOX_
BRM_
2.0
N
N60G
B5.4K
NSM8
X
ABT_
BRM4
318BG
N
N
N
N60G
B5.4K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII5
N
N60G
B5.4K
NSM8
X
ABT_
BRM4
318BG
FOX_
BRM_
2.0
N
N14.1
WXGA
SO512
MBII6
N
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
FOX_
BRM_
2.0
BT
VoIP
PCMC
IA
ATMK
36
N14.1
WXGA
SO512
MBII6
N
N100
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
FOX_
BRM_
2.0
BT
VoIP
PCMC
IA
AS5052WX
Mi
MCETC9
UMAC
1*512/120/
BT/6L/5R/
CB_bg_0.3
C_AN
ATTL5
0
N14.1
WXGA
G
SO512
MBII5
N
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
FOX_
BRM_
2.0
N
LX.AV
305.04
6
AS5052WX
Mi
XPHTC1
UMAC
1*512/120/
BT/6L/5R/
CB_bg_0.3
C_AN
ATTL5
0
N14.1
WXGA
G
SO512
MBII5
N
N120
GB5.4
K
NSM8
X
ABT_
ATH54
13BG
FOX_
BRM_
2.0
N
LX.AV
30J.05
9
AS5051AW
XMi
MCESW8
UMAC
2*512/120/
BT/6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
FOX_
BRM_
2.0
N
CPU
LCD
DIMM
1
DIMM
2
HDD 1
(GB)
ODD
AS5051AN
WXMi
LINPUSAR
7 UMAC
1*512/60/
BT/6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
N
N60G
B5.4K
LX.AV
30C.0
21
AS5051AN
WXMi
LINPUSFR
A UMAC
1*512/60/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
N
Russia
LX.AV
30C.0
23
AS5051AN
WXMi
LINPUSRU
5 UMAC
1*512/60/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
EMEA
Middle
East
LX.AV
305.04
4
AS5051AW
XMi
XPHAR8
UMAC
1*512/60/
BT/6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
AS505
1AWX
Mi
EMEA
Eastern
Europe
LX.AV
30J.05
7
AS5051AW
XMi
MCEPL7
UMAC
1*512/100/
BT/6L/
5R_bg_VP
_0.3C_AN
ATMK
36
AS505
1AWX
Mi
EMEA
Russia
LX.AV
305.04
5
AS5051AW
XMi
XPHRU1
UMAC
1*512/100/
BT/6L/
5R_bg_VP
_0.3C_AN
AS505
2WXM
i
TWN
GCTWN
LX.AV
30J.05
8
AS505
2WXM
i
TWN
GCTWN
AS505
1AWX
Mi
EMEA
Switzerland
Model
RO
AS505
1ANW
XMi
EMEA
Middle
East
LX.AV
30C.0
20
AS505
1ANW
XMi
EMEA
France
AS505
1ANW
XMi
EMEA
AS505
1AWX
Mi
Appendix A
Country
Descriptio
n
184
185
Acer
Part
no
DIMM
1
DIMM
2
HDD 1
(GB)
N14.1
WXGA
G
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
AS5051AW
XMi
MCEESJ
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
LX.AV
30J.06
4
AS5051AW
XMi
MCEDEA
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
Germany
LX.AV
30J.06
5
AS5051AW
XMi
MCEDEB
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
EMEA
Middle
East
LX.AV
30J.07
0
AS5051AW
XMi
MCEAR1
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
AS505
1AWX
Mi
EMEA
Middle
East
LX.AV
30J.08
4
AS5051AW
XMi
MCEAR2
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
AS505
1AWX
Mi
EMEA
Belgium
LX.AV
30J.06
6
AS505
1AWX
Mi
EMEA
Eastern
Europe
LX.AV
30J.07
9
Model
RO
Country
AS505
1AWX
Mi
EMEA
Switzerland
LX.AV
30J.06
0
AS505
1AWX
Mi
EMEA
Portugal
AS505
1AWX
Mi
EMEA
AS505
1AWX
Mi
Descriptio
n
Wirele
ss
LAN
Blueto
oth
VOIP
Phone
ABT_
BRM4
318BG
N
N
NSM8
X
ABT_
BRM4
318BG
N
N
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS5051AW
XMi
MCEBE6
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS5051AW
XMi
MCECS5
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
CPU
LCD
AS5051AW
XMi
MCESW8
UMAC
2*512/120/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
LX.AV
30J.06
1
AS5051AW
XMi
MCEPT6
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
Spain
LX.AV
30J.06
2
EMEA
Germany
AS505
1AWX
Mi
EMEA
AS505
1AWX
Mi
ODD
Appendix A
Acer
Part
no
CPU
LCD
DIMM
1
DIMM
2
HDD 1
(GB)
AS5051AW
XMi
MCENL6
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
LX.AV
30J.07
1
AS5051AW
XMi
MCEIT7
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
Denmark
LX.AV
30J.07
4
AS5051AW
XMi
MCEDK6
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
EMEA
France
LX.AV
30J.06
3
AS5051AW
XMi
MCEFRF
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
AS505
1AWX
Mi
EMEA
Norway
LX.AV
30J.07
3
AS5051AW
XMi
MCENO5
UMAC
1*512/80/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
AS505
1AWX
Mi
EMEA
Norway
LX.AV
30J.07
5
AS5051AW
XMi
MCENO5
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
AS505
1AWX
Mi
EMEA
Russia
LX.AV
30J.08
0
AS5051AW
XMi
MCERU9
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
AS505
1AWX
Mi
EMEA
Slovenia/
Croatia
LX.AV
30J.08
5
AS505
1AWX
Mi
EMEA
Switzerland
LX.AV
30J.08
6
Model
RO
AS505
1AWX
Mi
EMEA
Holland
LX.AV
30J.06
9
AS505
1AWX
Mi
EMEA
Italy
AS505
1AWX
Mi
EMEA
AS505
1AWX
Mi
Appendix A
Country
Descriptio
n
Wirele
ss
LAN
Blueto
oth
VOIP
Phone
ABT_
BRM4
318BG
N
N
NSM8
X
ABT_
BRM4
318BG
N
N
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII6
N
N80G
B5.4K
NSM8
X
ABT_
BRM4
318BG
N
N
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS5051AW
XMi
MCESI1
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS5051AW
XMi
MCESW8
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
ODD
186
187
Acer
Part
no
CPU
LCD
DIMM
1
DIMM
2
HDD 1
(GB)
AS5051AW
XMi
MCEPL7
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
LX.AV
30J.06
7
AS5051AW
XMi
MCESV5
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
UK
LX.AV
30J.08
1
AS5051AW
XMi
MCEUUK1
1U UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
EMEA
UK
LX.AV
30J.08
7
AS5051AW
XMi
MCEUK5
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
AS505
1AWX
Mi
EMEA
Turkey
LX.AV
30J.07
2
AS5051AW
XMi
MCETR5
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
AS505
1AWX
Mi
EMEA
Italy
LX.AV
30J.07
6
AS5051AW
XMi
MCEWIT11
W UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
AS505
1AWX
Mi
EMEA
UK
LX.AV
30J.08
8
AS5051AW
XMi
MCEUK6
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
AS505
1AWX
Mi
EMEA
France
LX.AV
30J.07
7
AS505
1AWX
Mi
EMEA
Germany
LX.AV
30J.07
8
Model
RO
Country
AS505
1AWX
Mi
EMEA
Eastern
Europe
LX.AV
30J.06
8
AS505
1AWX
Mi
EMEA
Sweden/
Finland
AS505
1AWX
Mi
EMEA
AS505
1AWX
Mi
Descriptio
n
Wirele
ss
LAN
Blueto
oth
VOIP
Phone
ABT_
BRM4
318BG
N
N
NSM8
X
ABT_
BRM4
318BG
N
N
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS5051AW
XMi
MCEWFR1
1W UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS5051AW
XMi
MCEWDE1
1W UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
ODD
Appendix A
Acer
Part
no
CPU
LCD
DIMM
1
DIMM
2
HDD 1
(GB)
AS5051AW
XMi
XPHDE7
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
LX.AV
305.06
1
AS5051AW
XMi
XPHAR1
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
Denmark
LX.AV
305.04
7
AS5051AW
XMi
XPHDK1
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
EMEA
Belgium
LX.AV
305.05
6
AS5051AW
XMi
XPHBE1
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
AS505
1AWX
Mi
EMEA
Eastern
Europe
LX.AV
305.05
2
AS5051AW
XMi
XPHCS2
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
AS505
1AWX
Mi
EMEA
UK
LX.AV
30J.08
3
AS5051AW
XMi
MCEWUK1
1W UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
AS505
1AWX
Mi
EMEA
UK
LX.AV
30J.08
2
AS5051AW
XMi
MCEWUK2
1W UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
AS505
1AWX
Mi
EMEA
Eastern
Europe
LX.AV
305.05
1
AS505
1AWX
Mi
EMEA
Spain
LX.AV
305.05
9
Model
RO
AS505
1AWX
Mi
EMEA
Germany
LX.AV
305.05
7
AS505
1AWX
Mi
EMEA
Middle
East
AS505
1AWX
Mi
EMEA
AS505
1AWX
Mi
Appendix A
Country
Descriptio
n
Wirele
ss
LAN
Blueto
oth
VOIP
Phone
ABT_
BRM4
318BG
N
N
NSM8
X
ABT_
BRM4
318BG
N
N
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS5051AW
XMi
XPHHU6
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS5051AW
XMi
XPHESA
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
ODD
188
189
Acer
Part
no
CPU
LCD
DIMM
1
DIMM
2
HDD 1
(GB)
AS5051AW
XMi
XPHEL1
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
LX.AV
305.06
9
AS5051AW
XMi
XPHIS1
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
France
LX.AV
305.04
8
AS5051AW
XMi
XPHFRA
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
EMEA
Italy
LX.AV
305.05
5
AS5051AW
XMi
XPHIT1
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
AS505
1AWX
Mi
EMEA
Eastern
Europe
LX.AV
305.05
3
AS5051AW
XMi
XPHPL6
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
AS505
1AWX
Mi
EMEA
Holland
LX.AV
305.06
7
AS5051AW
XMi
XPHNL1
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
AS505
1AWX
Mi
AAP
Malaysia
LX.AV
305.06
6
AS5051AW
XMi
XPHMA2
UMAC
1*512/80/
6L/5R/
CB_bg_0.3
C_AN
AS505
1AWX
Mi
EMEA
Norway
LX.AV
305.05
8
AS505
1AWX
Mi
EMEA
South
Africa
LX.AV
305.06
2
Model
RO
Country
AS505
1AWX
Mi
EMEA
Greece
LX.AV
305.05
4
AS505
1AWX
Mi
EMEA
Israel
AS505
1AWX
Mi
EMEA
AS505
1AWX
Mi
Descriptio
n
Wirele
ss
LAN
Blueto
oth
VOIP
Phone
ABT_
BRM4
318BG
N
N
NSM8
X
ABT_
BRM4
318BG
N
N
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N80G
B5.4K
NSM8
X
ABT_
ATH54
13BG
N
N
AS5051AW
XMi
XPHNO1
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS5051AW
XMi
XPHSA1
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
ODD
Appendix A
Acer
Part
no
CPU
LCD
DIMM
1
DIMM
2
HDD 1
(GB)
AS5051AW
XMi
XPHRU2
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
LX.AV
305.05
0
AS5051AW
XMi
XPHSV1
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
Slovenia/
Croatia
LX.AV
305.06
3
AS5051AW
XMi
XPHSLO2
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
EMEA
Portugal
LX.AV
305.06
8
AS5051AW
XMi
XPHPT1
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
SO512
MBII5
AS505
1AWX
Mi
EMEA
Switzerland
LX.AV
305.06
4
AS5051AW
XMi
XPHSW5
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
AS505
1AWX
Mi
EMEA
UK
LX.AV
305.06
5
AS5051AW
XMi
XPHUK1
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
ATMK
36
AS505
1AWX
Mi
EMEA
Turkey
LX.AV
305.07
0
AS5051AW
XMi
XPHTR1
UMAC
2*512/120/
6L/
5R_bg_0.3
C_AN
AS505
1ANW
XMi
EMEA
Turkey
LX.AV
30C.0
25
AS505
1AWX
Mi
EMEA
Turkey
LX.AV
305.07
1
Model
RO
AS505
1AWX
Mi
EMEA
Russia
LX.AV
305.04
9
AS505
1AWX
Mi
EMEA
Sweden/
Finland
AS505
1AWX
Mi
EMEA
AS505
1AWX
Mi
Appendix A
Country
Descriptio
n
Wirele
ss
LAN
Blueto
oth
VOIP
Phone
ABT_
BRM4
318BG
N
N
NSM8
X
ABT_
BRM4
318BG
N
N
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
ATMK
36
N14.1
WXGA
SO512
MBII5
SO512
MBII5
N120
GB5.4
K
NSM8
X
ABT_
BRM4
318BG
N
N
AS5051AN
WXMi
LINPUSTR
1 UMAC
1*512/60/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N60G
B5.4K
NSM8
X
ABT_
BRM4
318BG
N
N
AS5051AW
XMi
XPHTR1
UMAC
1*512/60/
6L/5R/
CB_bg_0.3
C_AN
ATMK
36
N14.1
WXGA
G
SO512
MBII5
N
N60G
B5.4K
NSM8
X
ABT_
BRM4
318BG
N
N
ODD
190
Model
AS505
2NWX
Mi
191
RO
AAP
Country
India
Acer
Part
no
LX.AV
30C.0
26
Descriptio
n
AS5052N
WXMi
LINPUSIL1
UMAC
1*512/80/
BT/6L/5R/
CB_bg_0.3
C_AN
CPU
LCD
ATTL5
0
N14.1
WXGA
G
DIMM
1
DIMM
2
HDD 1
(GB)
ODD
SO512
MBII5
N
N80G
B5.4K
NSM8
X
Wirele
ss
LAN
Blueto
oth
VOIP
Phone
ABT_
ATH54
13BG
FOX_
BRM_
2.0
N
Appendix A
Appendix A
192
Appendix B
Test Compatible Components
This computer’s compatibility is tested and verified by Acer’s internal testing department. All of its system
functions are tested under Windows® XP Home, Windows® XP Pro environment.
Refer to the following lists for components, adapter cards, and peripherals which have passed these tests.
Regarding configuration, combination and test procedures, please refer to the Aspire 7730/7730G series
Compatibility Test Report released by the Acer Mobile System Testing Department.
Appendix B
193
Microsoft® Windows® Vista Environment Test
PCMCIA LAN Card Test
Type
Device specification
LAN Card 16 bit
3Com Megahertz LAN PC Card_589E (Ethernet)
LAN Card 32 bit
FE575C-3Com 10/100 LAN CardBus-Fast Ethernet
Express Card Test
Type
Device specification
1394 Express Card
AboCom Express Card|54 1394B 800Mbs
TV Tuner Express
Card
AVerTV Hybrid Express Slim
Card Reader
Express Card
Maxell Express card|34 5in1 adapter
GigaLAN Express
Card
NETGEAR Gigabit PC card
Display Port Test
Type
External Monitor CRT Monitor
External Monitor LCD Monitor
Projector
HDTV - HDMI
Device specification
•
Λ OC 779S
•
View Sonic PF775 17"
•
Philip 109P
•
Dell 21" Monitor
•
View Sonic 1680*1050
•
CMV CM-930D 17" LCD (1280*1024)
•
ACER AL2423W LCD area with 1920*1200
•
Toshiba TV 37HL869 LCD area with 1366*768
•
BenQ FB8225(QSMC)
•
Panasonic PT-LC80U
•
Toshiba TV 37HL869 LCD area with 1366*768
•
FlexScan HD2441W with 1920*1080
•
NewMen KB-085 USB KEYBOARD
•
WiNTEK USB Keyboard
•
Logitech Cordless Mouse and Keyboard (USB, Wheel), Microsoft Wireless
Optical Desktop (USB|PS/2)
•
Logitech Wheel Mouse (Optical, USB|PS/2)
•
Huaerte mouse(USB)
•
NEC Mouse(USB|)
•
YAHOO XEPER Optical Mouse(USB)
•
Logitech (Optical)
•
Microsoft IntelliMouse Explorer 3.0 USB and PS/2 Compatible (Optical)
(QSMC)
USB Port Test
Type
Keyboard
Mouse
194
Device specification
Appendix B
Type
Printer
Device specification
•
Epson Stylus C65 Printer
•
HP deskjet 3535 Printer
Scanner
Canon USB2.0 Scanner
Speaker
•
SCLAR
•
OZAKI USB 5.1CH-IN-2SPK Digital Sound - US206
•
NAZAR GPC-V70
•
Logitech Freedom 2.4CordlessJoystick
Card Reader
•
5 in 1
•
HR8-U2M MS/MS-PRO/DUO
HDD
FUJITSU USB2.0 HDD
DVD CD/RW
•
YAMAHA CD-R/RW Drive
•
MP5125A DVD+RW/+R
•
NETAC 1G
•
Transcend 2G
•
IBM USB2.0 Device
•
Panasonic YD-8U10 USB1.0 Device
•
BELKIN USB1.1 SLIM HUB (QSMC)
•
D-Link 4-Port USB 2.0 Hub
•
Hi-Speed 4-Port USB 2.0 HUB (IOGEAR)
Joystick
Handy Drive
FDD
HUB
Access Point Test
Type
Wireless LAN AP
Device specification
•
D-Link 665
•
Guest
•
001601B8DD1A-G
•
Buffal0 WZR2-G300N(n)
Bluetooth Test
Type
Mouse
Appendix B
Device specification
•
ACER Bluetooth Mouse
•
Darfon Bluetooth Mouse (Ferrari 1000)
195
Card Reader Test
Type
MMC Card
SD Card
Device specification
•
Transcend 512MB MMC Card
•
Kingston 1G MMC Card
•
Sandisk 2.0G SD Card
•
A-Data 2G SD Card
•
Turbo Series SDHC 16GB CLASS 6
•
Sandisk microSDHC 8G SD Card
•
Transcend 2G SD Card
MS Card
Sandisk 64MB MS Card (QSMC)
MS Pro Card
Sony 256MB MS Card (MS Pro)
MS Duo Adapter
Sandisk Memory Stick Duo Adaptor
Micro SD
Transcend MicroSD 2G
XD Card
•
OLYMPUS XD Picture Card 1G
•
OLYMPUS XD Picture Card 512MB
•
Fujifilm XD Picture Card 512M
Audio Jacks Port Test
Type
Device specification
Speaker
Edifier Speaker
Head Phone
•
Jazz 369 Headphone
•
Philips Headphone
•
MO-J39 Headphone
SPDIF
Creative Inspire 5.1 digital 5600
Port Replicator Test
Type
Docking
196
Device specification
Cable Docking
Appendix B
Appendix C
Online Support Information
This section describes online technical support services available to help you repair your Acer Systems.
If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch
office. Acer Branch Offices and Regional Business Units may access our website. However some information
sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
Acer's Website offers you convenient and valuable support resources whenever you need them.
In the Technical Information section you can download information on all of Acer's Notebook, Desktop and
Server models including:
•
Service guides for all models
•
User's manuals
•
Training materials
•
Bios updates
•
Software utilities
•
Spare parts lists
•
TABs (Technical Announcement Bulletin)
For these purposes, we have included an Acrobat File to facilitate the problem-free downloading of our
technical material.
Also contained on this website are:
•
Detailed information on Acer's International Traveler's Warranty (ITW)
•
Returned material authorization procedures
•
An overview of all the support services we offer, accompanied by a list of telephone, fax and email
contacts for all your technical queries.
We are always looking for ways to optimize and improve our services, so if you have any suggestions or
comments, please do not hesitate to communicate these to us.
Appendix C
197
198
Appendix C
Index
A
display
hotkeys
AFLASH Utility
39
14
E
B
EasyTouch Failure
Battery Pack
46
Euro
BIOS
package 22
password control
ROM size 21
ROM type 21
vendor 21
Version 21
External Module Disassembly
22
Flowchart
45
F
Features 1
22
Fingerprint Reader Failure
27–39
Advanced 30
Boot 37
Exit 38
Navigating 27
BIOS Utility
141
39
FPC Cable 94
Flash Utility
FRU (Field Replaceable Unit) List
Onboard Device Configuration 33
Power 35
Save and Exit 38
Security 32
System Security 38
159
H
55
Hard Disk Drive2 Module 58
HDTV Switch Failure 142
Hard Disk Drive1 Module
81
Hibernation mode
Board Layout
14
Hot Keys 12
hotkey
Top View 155
brightness
hotkeys
15
ExpressCard Module 83
BIOS Supports protocol
Bluetooth board
140
I
14
C
Indicators 10
Camera Module
Intermittent Problems 144
92
134
Internal Speaker Failure 132
inverter board 91
Internal Microphone Failure
caps lock
on indicator
10
145
Common Problems 128
Chipset POST Codes
computer
on indicator
Jumper and Connector Locations
10
Core POST Codes
CPU
J
Top View 155
147
87
K
D
Keyboard
DIMM Module 50,
Display
4
155
65
Keyboard Failure 131
51
L
199
Launch Board
LCD Bezel
S
77
90
Speaker Module
94
LCD Failure 131
LCD Brackets
speakers
hotkey
LCD Module Disassembly
Flowchart
14
System
89
Block Diagram
93
lower covers 49
LCD Panel
4
T
Test Compatible Components 193
M
Thermal Unit Failure
Main Unit Disassembly
Flowchart
Mainboard
Top
62
on indicator
75
Touch Pad Failure 132
141
Troubleshooting
128
Model Definition 170
Modem Board 65
Modem Failure 139
Built-in KB Failure 131
EasyTouch Buttons 140
Fingerprint Reader 141
HDTV Switch 142
Internal Microphone 134
Internal Speakers 132
LCD Failure 131
MediTouch Buttons 141
Modem 139
No Display 129
ODD 136
Other Failures 143
Power On 128
Thermal Unit 142
Touch Pad 132
USB 139
WLAN 140
N
No Display Issue
129
Notebook Manager
14
num lock
10
O
ODD Failure
14
Touch Pad Bracket
10
Memory Check
on indicator
155
hotkey
MediaTouch Button Failure
hotkey
142
Touch Pad
85
media access
136
51
TV Tuner Module 53
Turbo RAM module
Online Support Information 197
optical drive module
60
U
P
Panel
144
USB Failure (Rightside) 139
Undetermined Problems
5
Bottom
left 5
PC Card
9
utility
BIOS
10
POST Codes
Power On Failure
27–39
W
Chipset 145
Core 147
Windows 2000 Environment Test
128
Wireless Function Failure
WLAN Board
200
79
54
140
194
Download PDF

advertising