ASRock 775i65GV Computer Hardware User Manual

775i65GV
User Manual
Version 1.0
Published July 2004
Copyright©2004 ASRock INC. All rights reserved.
1
Copyright Notice:
No part of this manual may be reproduced, transcribed, transmitted, or translated in
any language, in any form or by any means, except duplication of documentation by
the purchaser for backup purpose, without written consent of ASRock Inc.
Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for
identification or explanation and to the owners’ benefit, without intent to infringe.
Disclaimer:
Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed
as a commitment by ASRock. ASRock assumes no responsibility for any errors or
omissions that may appear in this manual.
With respect to the contents of this manual, ASRock does not provide warranty of
any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose.
In no event shall ASRock, its directors, officers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of profits, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the manual or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
ASRock Website: http://www.asrock.com
2
Contents
1 Introduction ................................................... 5
1.1
1.2
1.3
1.4
1.5
Package Contents ...........................................................
Specifications .................................................................
Supported AGP VGA Cards Lists ...................................
Motherboard Layout .......................................................
ASRock I/O PlusTM ...........................................................
5
6
8
10
11
2 Installation ..................................................... 12
Pre-installation Precautions .........................................................
2.1 CPU Installation ................................................................
2.2 Installation of CPU Fan and Heatsink ..............................
2.3 Installation of Memory Modules (DIMM) ..........................
2.4 Expansion Slots (PCI, AMR, and AGI Slots) ....................
2.5 Easy Dual Monitor Feature ..............................................
2.6 Jumpers Setup ................................................................
2.7 Onboard Headers and Connectors ................................
2.8 Serial ATA (SATA) Hard Disks Installation .......................
12
13
15
16
17
18
18
20
23
3 BIOS SETUP UTILITY .......................................... 24
3.1 Introduction .....................................................................
3.1.1 BIOS Menu Bar .....................................................
3.1.2 Navigation Keys ...................................................
3.2 Main Screen ....................................................................
3.3 Advanced Screen ..........................................................
3.3.1 CPU Configuration ................................................
3.3.2 Chipset Configuration ...........................................
3.3.3 ACPI Configuration ...............................................
3.3.4 IDE Configuration ..................................................
3.3.5 PCIPnP Configuration ............................................
3.3.6 Floppy Configuration ............................................
3.3.7 Super IO Configuration .........................................
3.3.8 USB Configuration ................................................
3.4 Hardware Health Event Monitoring Screen ....................
3.5 Boot Screen ....................................................................
3.5.1 Boot Settings Configuration .................................
3.5.2 Boot Device Priority ..............................................
3.6 Security Screen ..............................................................
3.7 Exit Screen ......................................................................
3
24
24
25
25
26
26
27
29
30
32
33
33
35
35
36
36
37
37
38
4 Software Support .......................................... 39
4.1 Install Operating System .................................................
4.2 Support CD Information ...................................................
4.2.1 Running Support CD .............................................
4.2.2 Drivers Menu ........................................................
4.2.3 Utilities Menu .........................................................
4.2.4 ASRock “PC-DIY Live Demo” Program .................
4.2.5 “LGA 775 CPU Installation Live Demo” Program ...
4.2.6 Contact Information ...............................................
4
39
39
39
39•
39
39
39
39
Chapter 1 Introduction
Thank you for purchasing ASRock 775i65GV motherboard, a reliable motherboard
produced under ASRock’s consistently stringent quality control. It delivers excellent
performance with robust design conforming to ASRock’s commitment to quality and
endurance.
In this manual, chapter 1 and 2 contain introduction of the motherboard and step-bystep guide to the hardware installation. Chapter 3 and 4 contain the configuration
guide to BIOS setup and information of the Support CD.
Because the motherboard specifications and the BIOS software might be
updated, the content of this manual will be subject to change without
notice. In case any modifications of this manual occur, the updated
version will be available on ASRock website without further notice. You
may find the latest memory and CPU support lists on ASRock website as
well. ASRock website http://www.asrock.com
1.1 Package Contents
ASRock 775i65GV Motherboard
(Micro ATX Form Factor: 9.6-in x 8.6-in, 24.4 cm x 21.8 cm)
ASRock 775i65GV Quick Installation Guide
ASRock 775i65GV Support CD (including LGA 775 CPU Installation Live Demo)
One 80-conductor Ultra ATA 66/100 IDE Ribbon Cable
One Ribbon Cable for a 3.5-in Floppy Drive
One Serial ATA (SATA) Data Cable
One Serial ATA (SATA) HDD Power Cable (Optional)
One ASRock I/O PlusTM Shield
One COM Port Bracket
One ASRock MR Card (Optional)
5
1.2 Specifications
Platform:
CPU:
Micro ATX Form Factor: 9.6-in x 8.6-in, 24.4 cm x 21.8 cm
775-Pin Socket
supporting Intel® Pentium® 4 / Celeron® processor (in 775-land
LGA package)
North Bridge:
Intel® 865GV chipset, FSB @ 800 / 533 MHz,
supports Hyper-Threading Technology (see CAUTION 1)
South Bridge:
Intel® ICH5, supports SATA 1.5Gb/s
Memory:
2 DDR DIMM slots: DDR1 and DDR2
supports PC3200 (DDR400) / PC2700 (DDR333) /
PC2100 (DDR266), Max. 2GB (see CAUTION 2)
Dual Channel Memory Technology support(see CAUTION 3)
IDE:
IDE1: ATA 100 / Ultra DMA Mode 5
IDE2: ATA 100 / Ultra DMA Mode 5
Supports up to 4 IDE devices
Serial ATA:
Supports up to 2 SATA devices at 1.5Gb/s data transfer rate.
(No Support for “RAID” and “Hot Plug” functions)
Floppy Port:
Supports up to 2 floppy disk drives
Audio:
5.1 channels AC’97 Audio
PCI LAN:
Speed: 802.3u (10/100 Ethernet), supports Wake-On-LAN
Hardware Monitor:CPU temperature sensing
Motherboard temperature sensing
CPU overheat shutdown to protect CPU life
(ASRock U-COP)(see CAUTION 4)
CPU fan tachometer
Chassis fan tachometer
Voltage monitoring: +12V, +5V, +3.3V, Vcore
PCI slots:
3 PCI slots with PCI Specification 2.2 (see CAUTION 5)
AMR slot:
1 slot, supports ASRock MR card (Optional)
AGI slot:
1 AGI [ASRock Graphics Interface] slot (see CAUTION 6)
USB 2.0:
8 USB 2.0 ports:
includes 6 default USB 2.0 ports on the rear panel,
plus one header to support 2 additional USB 2.0 ports
(see CAUTION 7)
ASRock I/O PlusTM: 1 PS/2 mouse port, 1 PS/2 keyboard port,
1 VGA port, 1 parallel port: ECP/EPP support,
6 default USB 2.0 ports,
1 RJ-45 port,
Audio Jack: Line In / Line Out / Microphone
Chipsets:
6
COM Port:
BIOS:
1 COM Port Header to support a COM port module
AMI legal BIOS, Supports “Plug and Play”,
ACPI 1.1 compliance wake up events,
CPU frequency stepless control
(only for advanced users’ reference, see CAUTION 8)
Microsoft® Windows® 98 SE / ME / 2000 / XP compliant
OS:
CAUTION!
1.
2.
About the setting of “Hyper Threading Technology”, please check page 27.
Please check the table below for the memory support frequency and its
corresponding CPU FSB frequency.
CPU FSB Frequency
Memory Support Frequency
800
DDR266, DDR320*, DDR400
533
DDR266, DDR333
* When you use an FSB800-CPU on this motherboard, it will run at
DDR320 if you adopt a DDR333 memory module.
3.
4.
This motherboard supports Dual Channel Memory Technology. Before you
implement Dual Channel Memory Technology, make sure to read the
installation guide of memory modules on page 16 for proper installation.
While CPU overheat is detected, the system will automatically shutdown.
Before you resume the system, please check if the CPU fan on the
motherboard functions properly and unplug the power cord, then plug it
back again. To improve heat dissipation, remember to spray thermal
grease between the CPU and the heatsink when you install the PC system.
5.
Because the installed AMR card will occupy the same external connecting
position with the PCI card that are installed in “PCI3” slot, you will not be
able to install any PCI card in “PCI3” slot if an AMR card has already been
installed in the AMR slot.
6.
The AGI [ASRock Graphics Interface] slot is a special design that only
supports compatible AGP VGA cards. For the information of the
compatible AGP VGA cards, please refer to the “Supported AGP VGA
Cards List” on page 8 and page 9. For the proper installation of AGP
7.
VGA card, please refer to the installation guide on page 17.
Power Management for USB 2.0 works fine under Microsoft® Windows® XP
SP1 / 2000 SP4. It may not work properly under Microsoft® Windows® 98/
ME. Please refer to Microsoft® official document at
8.
http://www.microsoft.com/whdc/hwdev/bus/USB/USB2support.mspx
Although this motherboard offers stepless control, it is not recommended
to perform over-clocking. Frequencies other than the recommended CPU
bus frequencies may cause the instability of the system or damage the
CPU.
7
1.3
Supported AGP VGA Cards List
(for Windows 2000/Windows XP)
I. AGP 4X
Graphics Chip
Vendor
n-VIDIA
Model Name
ASUS AGP-V7100
ASUS AGP-V7100PRO
ASUS AGP-V7100 MAGIC / 32M
ASUS AGP-V7700Ti
ASUS AGP-V8170DDR
ASUS AGP-V8170SE / LP
ASUS AGP-V8200 T2
ASUS AGP-V8200 T5
ASUS AGP-V8440
ASUS AGP-V8460 Ultra
GAINWARD- GF3-TI500/64M
GAINWARD- GF3-TI500/128M
Inno3D GeForce2 MX400
Leadtek WinFast A170 TH
Leadtek WinFast A170 DDR
Leadtek WinFast A250LE TD
Leadtek WinFast GeForce2 MX MX64
Leadtek WinFast GeForce2 H MX400
MSI- GF4-MX440SE
PROLINK GF4-MX440
ATI
SPARKLE GF4-MX440
Gigabyte GV-AP64D
Gigabyte GV-AP64D-H
Gigabyte GV-AR64S-H
POWERCOLOR RADEON 9000
POWERCOLOR RADEON 9100
SiS
TRANSCEND TS64MVDR7
SYNNEX GCM-SiS315EA32
For the latest updates of the supported AGP VGA cards list, please visit
ASRock website for details.
ASRock website: http://www.asrock.com/support/index.htm
8
II. AGP 8X
Graphics Chip
Vendor
n-VIDIA
Model Name
ALBATRON GF4-MX440 64M
AOPEN Aeolus FX5600S-DV128
AOPEN Aeolus FX5200-V128
ASUS AGP-V9180
ASUS AGP-V9280 VIEDO SUITE
ASUS AGP-V9520 MAGIC/T
ASUS V9900
ASUS V9900 ULTRA
ELSA-GLADIC 518
ELSA-GLADIC 518 P
Inno3D GeForce FX5600
LEADTEK A280 LE
LEADTEK A340TDH
MSI Ti4800SE-VTD8X
PALIT GF4 MX440 8X 64MB
PROLINK GeForceFX5900
PROLINK GF4-TI4200
SPARKLE GF4-MX440-8X
ATI
CLUB3D ATI R9800
Gigabyte GV R9000 PRO
Gigabyte RADEON 9500
Gigabyte RADEON 9700 PRO
POWER COLOR 9200
SAPHIRE RADEON 9200-128MB
SiS
POWER COLOR XABRE600
For the latest updates of the supported AGP VGA cards list, please visit
ASRock website for details.
ASRock website: http://www.asrock.com/support/index.htm
9
1.4 Motherboard Layout
4
3
2
1
5
6
21.8cm (8.6 in)
1
PS2
Mouse
DDR400
USB 2.0
T: USB2
B: USB3
FSB1
1
USB 2.0
T: USB4
B: USB5
USB4_5
el
t V
In 5G set
86 hip
C
2MB
BIOS
COM1
Top:
Line In
Bottom:
Mic In
25
24
23
22
21
Center:
Line Out
26
1
Super
I/O
8
9
SATA2
PCI
LAN
Intel
ICH5
775 i65GV
JR1 AUDIO1
JL1 1
USB2.0
PCI 2
5.1CH
CMOS
Battery
PCI 3
AUX1
20
SATA1
SPEAKER1
1
IR1
AMR1
CLRCMOS0
FLOPPY1
19
PS2_USB_PWR1 Jumper
775-Pin CPU Socket
North Bridge Controller
CPU Fan Connector (CPU_FAN1)
184-pin DDR DIMM Slots (DDR1- 2, Dual Channel)
ATX Power Connector (ATXPWR1)
Primary IDE Connector (IDE1, Blue)
Secondary IDE Connector (IDE2, Black)
ASRock Graphics Interface Slot (1.5V_AGP1)
South Bridge Controller
Secondary Serial ATA Connector (SATA2)
Primary Serial ATA Connector (SATA1)
Chassis Speaker Header (SPEAKER 1)
Chassis Fan Connector (CHA_FAN1)
USB 2.0 Header (USB67, Blue)
10
18
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
PANEL1
17
CHA_FAN1
PLED PWRBTN
1
HDLED
1
10
11
PCI 1
AUDIO
CODEC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
7
SATA
1.5V_AGP1
CD1
IDE2 IDE1
FSB800
27
1
Top:
RJ-45
USB 2.0
T: USB0
B: USB1
28
Prescott 800
29
DDR1 (64/72 bit, 184-pin module)
ATX12V1
30
DDR2 (64/72 bit, 184-pin module)
CPU_FAN1
Dual Channel
VGA1
ATXPWR1
PARALLEL PORT
PS2
Keyboard
24.4cm (9.6 in)
PS2_USB_PWR1
12
13
14
1
RESET
USB67
16 15
System Panel Header (PANEL1)
Infrared Module Header (IR1)
Clear CMOS Jumper (CLRCMOS0)
Floppy Connector (FLOPPY1)
AMR Slot (AMR1)
Internal Audio Connector: CD1 (Black)
Internal Audio Connector: AUX1 (White)
PCI Slots (PCI1- 3)
JR1 Jumper / JL1 Jumper
Front Panel Audio Header (AUDIO1)
COM Port Header (COM1)
Shared USB 2.0 Header (USB4_5, Blue)
BIOS FWH Chip
FSB Select Jumper (FSB1)
ATX 12V Connector (ATX12V1)
1.5 ASRock I/O Plus TM
2
1
3
4
5
11
1
2
3
4
5
6
10
9
8
Parallel Port
RJ-45 Port
Line In (Light Blue)
Line Out (Lime)
Microphone (Pink)
Shared USB 2.0 Ports (USB45)
7
8
9
10
11
11
7
6
USB 2.0 Ports (USB01)
USB 2.0 Ports (USB23)
VGA Port
PS/2 Keyboard Port (Purple)
PS/2 Mouse Port (Green)
Chapter 2 Installation
775i65GV is a Micro ATX form factor (9.6-in x 8.6-in, 24.4 cm x 21.8 cm) motherboard.
Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard
components or change any motherboard settings.
Before you install or remove any component, ensure that the
power is switched off or the power cord is detached from the
power supply. Failure to do so may cause severe damage to the
motherboard, peripherals, and/or components.
1.
2.
3.
4.
5.
Unplug the power cord from the wall socket before touching any
component.
To avoid damaging the motherboard components due to static
electricity, NEVER place your motherboard directly on the carpet or
the like. Also remember to use a grounded wrist strap or touch a
safety grounded object before you handle components.
Hold components by the edges and do not touch the ICs.
Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that comes with the component.
When placing screws into the screw holes to secure the motherboard
to the chassis, please do not over-tighten the screws! Doing so may
damage the motherboard.
12
2.1 CPU Installation
For the installation of Intel 775-Pin CPU,
please follow the steps below.
775-Pin Socket Overview
Before you insert the 775-Pin CPU into the socket, please check if the
CPU surface is unclean or if there is any bent pin on the socket. Do
not force to insert the CPU into the socket if above situation is found.
Otherwise, the CPU will be seriously damaged.
Step 1. Open the socket:
Step 1-1. Disengaging the lever by depressing
down and out on the hook to clear
retention tab.
Step 1-2. Rotate the load lever to fully open position at approximately 135 degrees.
Step 1-3. Rotate the load plate to fully open position at approximately 100 degrees.
black line
black line
Step 2. Insert the 775-Pin CPU:
Step 2-1. Hold the CPU by the edges where are
marked with black lines.
Step 2-2. Orient the CPU with IHS (Integrated
Heat Sink) up. Locate Pin1 and the two
orientation key notches.
Pin1
orientation
key notch
Pin1
alignment key
orientation
key notch
alignment key
775-Pin Socket
775-Pin CPU
13
For proper inserting, please ensure to match the two orientation key
notches of the CPU with the two alignment keys of the socket.
Step 2-3. Carefully place the CPU into the socket
by using a purely vertical motion.
Step 2-4. Verify that the CPU is within the socket
and properly mated to the orient keys.
Step 3. Remove PnP Cap (Pick and Place Cap):
Use your left hand index finger and thumb to
support the load plate edge, engage PnP cap
with right hand thumb and peel the cap from the
socket while pressing on center of PnP cap to
assist in removal.
It is recommended to use the cap tab to handle and avoid kicking off
the PnP cap.
Step 4. Close the socket:
Step 4-1. Rotate the load plate onto the IHS.
Step 4-2. While pressing down lightly on load
plate, engage the load lever.
Step 4-3. Secure load lever with load plate tab
under retention tab of load lever.
14
2.2
Installation of CPU Fan and Heatsink
This motherboard is equipped with 775-Pin socket that supports Intel 775-Pin CPU.
Please adopt the type of heatsink and cooling fan compliant with Intel 775-Pin CPU to
dissipate heat. Before you installed the heatsink, you need to spray thermal interface
material between the CPU and the heatsink to improve heat dissipation. Ensure that
the CPU and the heatsink are securely fastened and in good contact with each other.
Then connect the CPU fan to the CPU_FAN connector (CPU_FAN1, see page 10,
No. 4).
For proper installation, please kindly refer to the instruction manuals of
your CPU fan and heatsink.
Below is an example to illustrate the installation of the heatsink for 775-Pin CPU.
Step 1. Apply thermal interface material onto center
of IHS on the socket surface.
Step 2.
Step 3.
Step 4.
Place the heatsink onto the socket. Ensure
fan cables are oriented on side closest to the
CPU fan connector on the motherboard
(CPU_FAN1, see page 10, No. 4).
Align fasteners with the motherboard
throughholes.
Rotate the fastener clockwise, then press
down on fastener caps with thumb to install
and lock. Repeat with remaining fasteners.
If you press down the fasteners without rotating them clockwise,
the heatsink cannot be secured on the motherboard.
Step 5.
Step 6.
Connect fan header with the CPU fan
connector on the motherboard.
Secure excess cable with tie-wrap to ensure
cable does not interfere with fan operation or
contact other components.
15
2.3 Installation of Memory Modules (DIMM)
775i65GV motherboard provides two 184-pin DDR (Double Data Rate) DIMM slots,
and supports Dual Channel Memory Technology. For dual channel configuration, you
always need to install two identical (the same brand, speed, size and chip-type)
memory modules in the DDR DIMM slots to activate Dual Channel Memory Technology.
Otherwise, it will operate at single channel mode.
If you install only one memory module or two non-identical memory
modules, it is unable to activate the Dual Channel Memory Technology.
Installing a DIMM
Please make sure to disconnect power supply before adding or
removing DIMMs or the system components.
Step 1.
Step 2.
Unlock a DIMM slot by pressing the retaining clips outward.
Align a DIMM on the slot such that the notch on the DIMM matches the break
on the slot.
notch
break
notch
break
The DIMM only fits in one correct orientation. It will cause permanent
damage to the motherboard and the DIMM if you force the DIMM into the
slot at incorrect orientation.
Step 3.
Firmly insert the DIMM into the slot until the retaining clips at both ends fully
snap back in place and the DIMM is properly seated.
16
2.4 Expansion Slots (PCI, AMR, and AGI Slots)
There are 3 PCI slots, 1 AMR slot, and 1 AGI slot on this motherboard.
PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI
interface.
Because the installed AMR card will occupy the same external
connecting position with the PCI card installed in “PCI3” slot, you
will no be able to install any PCI card in “PCI3” slot if an AMR card
has already been installed in the AMR slot.
AMR slot: AMR slot is used to insert an ASRock MR card (optional) with v.92
Modem functionality.
AGI slot: The AGI [ASRock Graphics Interface] slot is a special design that only
supports compatible AGP VGA cards. For the information of the compatible AGP VGA cards, please refer to the “Supported AGP VGA Cards List”
on page 8 and page 9.
To install the system with an add-on AGP VGA card, you must make
sure to install the driver of add-on AGP VGA card before you install
the onboard VGA driver. If the onboard VGA driver has already been
installed before you install the add-on AGP VGA card, the system will
automatically set the onboard VGA as the primary graphics adapter. In
that case, if you want to install the add-on AGP VGA card, you need
to remove the onboard VGA driver first, and then install the add-on
AGP VGA card and its driver. For the detailed instruction, please refer
to the documents in the Support CD, “AGI Slot Installation Guide (for
Windows 2000)” and “AGI Slot Installation Guide (for Windows XP)”,
which are located in the folder at the following path:
..\ Easy Dual Monitor
Installing an expansion card
Step 1.
Step 2.
Step 3.
Step 4.
Step 5.
Step 6.
Before installing the expansion card, please make sure that the power
supply is switched off or the power cord is unplugged. Please read the
documentation of the expansion card and make necessary hardware
settings for the card before you start the installation.
Remove the system unit cover (if your motherboard is already installed in a
chassis).
Remove the bracket facing the slot that you intend to use. Keep the screws
for later use.
Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
Fasten the card to the chassis with screws.
Replace the system cover.
17
2.5 Easy Dual Monitor Feature
Thanks to ASRock patented AGI8X Technology, this motherboard supports Easy
Dual Monitor upgrade. With the internal onboard VGA and the external add-on AGP
VGA card, you can easily enjoy the benefits of Dual Monitor feature. For the
detailed instruction, please refer to the document at the following path in the
Support CD:
..\ Easy Dual Monitor
2.6 Jumpers Setup
The illustration shows how jumpers are
setup. When the jumper cap is placed on
pins, the jumper is “Short”. If no jumper cap
is placed on pins, the jumper is “Open”. The
illustration shows a 3-pin jumper whose pin1
and pin2 are “Short” when jumper cap is
placed on these 2 pins.
Jumper
PS2_USB_PWR1
Setting
1_2
2_3
(see p.10 No. 1)
+5V
+5VSB
Description
Short pin2, pin3 to enable
+5VSB (standby) for PS/2
or USB wake up events.
Note: To select +5VSB, it requires 2 Amp and higher standby current provided by
power supply.
FSB Select Jumper
2_3
1_2
(see p.10 No. 29)
NORMAL
TEST
Note: The default setting of the FSB Select jumper is “NORMAL” (short pin1, pin2).
For the system’s stability, please keep the default setting.
JR1 / JL1 Jumpers
JR1
(see p.10 No. 24)
JL1
Note: If JR1 and JL1 Jumpers are short, both the front panel and the rear panel
audio connectors can work.
18
Clear CMOS
(CLRCMOS0)
(see p.10 No. 18)
2-pin jumper
Note: CLRCMOS0 allows you to clear the data in CMOS. The data in CMOS includes
system setup information such as system password, date, time, and system
setup parameters. To clear and reset the system parameters to default setup,
please turn off the computer and unplug the power cord from the power
supply. After waiting for 15 seconds, use a jumper cap to short the Clear CMOS
jumper for 5 seconds. After shorting the Clear CMOS jumper, please remove
the jumper cap. However, please do not clear the CMOS right after you update
the BIOS. If you need to clear the CMOS when you just finish updating the BIOS,
you must boot up the system first, and then shut it down before you do the
clear-CMOS action.
19
2.7 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!
FDD connector
(33-pin FLOPPY1)
Pin1
(see p.10 No. 19)
FLOPPY1
the red-striped side to Pin1
Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE connector (Blue)
Secondary IDE connector (Black)
(39-pin IDE1, see p.10 No. 7)
(39-pin IDE2, see p.10 No. 8)
PIN1
IDE1
PIN1
IDE2
connect the black end
connect the blue end
to the IDE devices
to the motherboard
80-conductor ATA 66/100 cable
Note: If you use only one IDE device on this motherboard, please set the IDE
device as “Master”. Please refer to the instruction of your IDE device vendor
for the details. Besides, to optimize compatibility and performance, please
connect your hard disk drive to the primary IDE connector (IDE1, blue) and
CD-ROM to the secondary IDE connector (IDE2, black).
Serial ATA Connectors
These two Serial ATA (SATA)
connectors support SATA data
cables for internal storage
devices. The current SATA
interface allows up to 1.5 Gb/s
data transfer rate.
SATA2
(SATA1: see p.10 No. 12)
(SATA2: see p.10 No. 11)
SATA1
Serial ATA (SATA)
Data Cable
Either end of the SATA data cable
can be connected to the SATA
hard disk or the SATA connector
on the motherboard.
20
Serial ATA (SATA)
Power Cable
Please connect the black end of
SATA power cable to the power
(Optional)
connector on each drive. Then
connect the white end of SATA
power cable to the power
connector of the power supply.
connect to the SATA HDD
power connector
connect to the
power supply
USB 2.0 Header
USB_PWR
P-6
P+6
GND
DUMMY
(9-pin USB67)
(see p.10 No. 15)
1
GND
P+7
P-7
USB_PWR
1
Shared USB 2.0 Header
USB_PWR
USB_PWR
P-4
P+4
GND
(9-pin USB4_5)
(see p.10 No. 27)
P-5
P+5
GND
DUMMY
IRTX
+5V
DUMMY
Infrared Module Header
1
GND
IRRX
Internal Audio Connectors
(4-pin CD1, 4-pin AUX1)
GND
CD-L
GND
CD-R
GND
AUX-L
GND
AUX-R
(CD1: see p.10 No. 21)
(AUX1: see p.10 No. 22)
CD1
Front Panel Audio Header
AUX1
GND
+5VA
BACKOUT-R
BACKOUT-L
(9-pin AUDIO1)
(see p.10 No. 25)
1
AUD-OUT-L
GND
AUD-OUT-R
MIC-POWER
MIC
21
This USB4_5 connector is shared
with the USB 2.0 ports 4,5 on
ASRock I/O PlusTM. When using
the front panel USB ports by
attaching the front panel USB
cable to this connector
(USB4_5), the USB ports 4,5 on
ASRock I/O PlusTM will not be able
to function.
This header supports an
optional wireless transmitting
and receiving infrared module.
(5-pin IR1)
(see p.10 No. 17)
ASRock I/O PlusTM accommodates 6 default USB 2.0 ports. If
those USB 2.0 ports on the I/O
panel are not sufficient, this
USB 2.0 header is available to
support 2 additional USB 2.0
ports.
These connectors allow you
to receive stereo audio input
from sound sources such as
a CD-ROM, DVD-ROM, TV
tuner card, or MPEG card.
This is an interface for front
panel audio cable that allows
convenient connection and
control of audio devices.
PLED+
PLEDPWRBTN#
GND
System Panel Header
(9-pin PANEL1)
(see p.10 No. 16)
This header accommodates
several system front panel
functions.
1
DUMMY
RESET#
GND
HDLEDHDLED+
Chassis Speaker Header
1
SPEAKER
DUMMY
DUMMY
+5V
(4-pin SPEAKER 1)
(see p.10 No. 13)
Chassis Fan Connector
GND
+12V
CHA_FAN_SPEED
(3-pin CHA_FAN1)
(see p.10 No. 14)
CPU Fan Connector
(4-pin CPU_FAN1)
N/C
CPU_FAN_SPEED
+12V
GND
(see p.10 No. 4)
Please connect the chassis
speaker to this header.
Please connect a chassis fan
cable to this connector and
match the black wire to the
ground pin.
You may connect either a 3-pin
or a 4-pin CPU fan cable to this
connector, then match the black
wire to the ground pin.
Note: If you use a 3-pin CPU fan cable, insert it to the connector by aligning it with the pins
“GND”, “+12V”, and “CPU_FAN_SPEED”.
ATX Power Connector
Please connect an ATX power
supply to this connector.
(20-pin ATXPWR1)
(see p.10 No. 6)
RRXD1
DDTR#1
DDSR#1
CCTS#1
COM Port Header
(9-pin COM1)
(see p.10 No. 26)
1
This COM port header is used
to support a COM port module.
RRI#1
RRTS#1
GND
TTXD1
DDCD#1
ATX 12V Connector
Please note that it is necessary
to connect a power supply with
ATX 12V plug to this connector
so that it can provides sufficient
power. Failing to do so will cause
the failure to power up.
(4-pin ATX12V1)
(see p.10 No. 30)
22
2.8
Serial ATA (SATA) Hard Disks Installation
This motherboard adopts Intel ICH5 south bridge chipset that supports Serial ATA
(SATA) hard disks. You may install SATA hard disks on this motherboard for
internal storage devices. This section will guide you to install the SATA hard disks.
STEP 1: Install the SATA hard disks into the drive bays of your chassis.
STEP 2: Connect the SATA power cable to the SATA hard disk.
STEP 3: Connect one end of the SATA data cable to the motherboard’s SATA
connector.
STEP 4: Connect the other end of the SATA data cable to the SATA hard disk.
Before you install OS into the SATA hard disk, you need to check and
ensure the configuration of the OnBoard IDE Operate Mode option in
BIOS setup is correct according to the condition of your system. For
the configuration details, please refer to the instruction on page 30.
23
Chapter 3 BIOS SETUP UTILITY
3.1
Introduction
This section explains how to use the BIOS SETUP UTILITY to configure your system.
The BIOS FWH chip on the motherboard stores the BIOS SETUP UTILITY. You may
run the BIOS SETUP UTILITY when you start up the computer. Please press <F2>
during the Power-On-Self-Test (POST) to enter the BIOS SETUP UTILITY, otherwise,
POST will continue with its test routines.
If you wish to enter the BIOS SETUP UTILITY after POST, restart the system by
pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system
chassis. You may also restart by turning the system off and then back on.
Because the BIOS software is constantly being updated, the
following BIOS setup screens and descriptions are for reference purpose only, and they may not exactly match what you
see on your screen.
3.1.1 BIOS Menu Bar
The top of the
Main
Advanced
H/W Monitor
Boot
screen has a menu bar with the following selections:
To set up the system time/date information
To set up the advanced BIOS features
To display current hardware status
To set up the default system device to locate and load the
Operating System
Security
To set up the security features
Exit
To exit the current screen or the BIOS SETUP UTILITY
Use < > key or < > key to choose among the selections on the menu bar,
and then press <Enter> to get into the sub screen.
24
3.1.2 Navigation Keys
Please check the following table for the function description of each navigation
key.
Navigation Key(s)
/
/
+ / <Enter>
<F1>
<F9>
<F10>
<ESC>
Function Description
Moves cursor left or right to select Screens
Moves cursor up or down to select items
To change option for the selected items
To bring up the selected screen
To display the General Help Screen
To load optimal default values for all the settings
To save changes and exit the BIOS SETUP UTILITY
To jump to the Exit Screen or exit the current screen
3.2 Main Screen
When you enter the BIOS SETUP UTILITY, the Main screen will appear and display
the system overview
Advanced
Main
BIOS SETUP UTILITY
H/W Monitor
Boot
[14:00:09]
[Wed 06/30/2004]
Use [+] or [-] to
configure system Time.
: 775i65GV BIOS P1.00
BIOS Version
: Genuine Intel (R) Pentium (R) CPU 3.20 GHz
Processor Type
Processor Speed : 3200 MHz
: 1024KB
Cache Size
Microcode Update : 0F34/0E
Total Memory
DIMM 1
DIMM 2
Exit
Use [Enter], [TAB]
or [SHIFT-TAB] to
select a field.
System Overview
System Time
System Date
Security
: 512MB with 8MB share memory
Dual-Channel Memory Mode
: 256MB/166MHz (DDR333)
: 256MB/166MHz (DDR333)
+Tab
F1
F9
F10
ESC
Select Screen
Select Item
Change Field
Select Field
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
System Time [Hour:Minute:Second]
Use this item to specify the system time.
System Date [Day Month/Date/Year]
Use this item to specify the system date.
25
3.3 Advanced Screen
In this section, you may set the configurations for the following items: CPU
Configuration, Chipset Configuration, ACPI Configuration, IDE Configuration, PCIPnP
Configuration, Floppy Configuration, SuperIO Configuration, and USB Configuration.
Main
Advanced
BIOS SETUP UTILITY
H/W Monitor
Boot
Security
Exit
Configure CPU
Advanced Settings
WARNING : Setting wrong values in below sections
may cause system to malfunction.
CPU Configuration
Chipset Configuration
ACPI Configuration
IDE Configuration
PCIPnP Configuration
Floppy Configuration
SuperIO Configuration
USB Configuration
Enter
F1
F9
F10
ESC
Select Screen
Select Item
Go to Sub Screen
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
Setting wrong values in this section may cause
the system to malfunction.
3.3.1 CPU Configuration
BIOS SETUP UTILITY
Advanced
Select how to set the
CPU host frequency.
CPU Configuration
CPU Host Frequency
Actual Frequency (MHz)
[Auto]
[200]
Spread Spectrum
[Disabled]
Ratio Status
Ratio Actual Value
Ratio CMOS Setting
: UnLocked
: 16
: [16]
CPU Thermal Throttling
[Enabled]
Hyper Threading Technology
[Auto]
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
CPU Host Frequency
While entering setup, BIOS auto detects the present CPU host frequency of
this motherboard. The actual CPU host frequency will show in the following
item.
Spread Spectrum
This item should always be [Disabled] for better system stability.
26
Ratio Status
This is a read-only item, which displays whether the ratio status of this
motherboard is “Locked” or “Unlocked”. If it shows “Unlocked”, you will find
an item Ratio CMOS Setting appears to allow you changing the ratio value
of this motherboard. If it shows “Locked”, then the item Ratio CMOS Setting will be hidden. If you use the ratio value to time the CPU frequency, it will
be equal to the core speed of the installed processor.
Ratio Actual Value
This is a read-only item, which displays the ratio actual value of this
motherboard.
Ratio CMOS Setting
If the ratio status of this motherboard is “Unlocked”, this item will display and
allow you to set the ratio value between CPU Core Clock and the FSB
frequency.
CPU Thermal Throttling
You may select [Enabled] to enable P4 CPU internal thermal control mechanism to keep the CPU from overheated.
Hyper Threading Technology
To enable this feature, it requires a computer system with an Intel Pentium®4
processor that supports Hyper-Threading technology and an operating system that includes optimization for this technology, such as Microsoft® Windows® XP. Set to [Auto] if using Microsoft® Windows® XP, or Linux kernel
version 2.4.18 or higher. This option will be hidden if the installed CPU does
not support Hyper-Threading technology.
3.3.2 Chipset Configuration
BIOS SETUP UTILITY
Advanced
Chipset Configuration
Options
133MHz (DDR266)
166MHz (DDR333)
200MHz (DDR400)
Auto
DRAM Frequency
Flexibility Option
Configure DRAM Timing by SPD
DRAM CAS# Latency
DRAM RAS# Precharge
DRAM RAS# to CAS# Delay
DRAM Precharge Delay
DRAM Burst Length
[Auto]
[Disabled]
[Disabled]
[Auto]
[4 Clocks]
[4 Clocks]
[8 Clocks]
[4]
Init. Graphic Adapter Priority
Internal Graphics Mode Select
[PCI / AGI / Onboard]
[Auto]
OnBoard LAN
OnBoard AC'97 Audio
OnBoard MC'97 Modem
[Enabled]
[Auto]
[Auto]
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
27
DRAM Frequency
If [Auto] is selected, the motherboard will detect the memory module(s)
inserted and assigns appropriate frequency automatically. You may also
select other value as operating frequency: [133MHz (DDR 266)],
[166MHz (DDR 333)], [200MHz (DDR 400)].
Flexibility Option
The default value of this option is [Disabled]. It will allow better tolerance for
memory compatibility when it is set to [Enabled].
Configure DRAM Timing by SPD
Select [Enabled] will configure the following items by the contents in the
SPD (Serial Presence Detect) device.
DRAM CAS# Latency
Use this item to adjust the means of memory accessing. Configuration
options: [Auto], [2.5], [2], and [3]. Please note that the configuration
option [3] is available only for FSB 800 and FSB 533.
DRAM RAS# Precharge
This controls the idle clocks after a precharge command is issued.
Configuration options: [4 Clocks], [3 Clocks], and [2 Clocks].
DRAM RAS# to CAS# Delay
This controls the latency between the DRAM active command and the
read / write command. Configuration options: [4 Clocks], [3 Clocks],
and [2 Clocks].
DRAM Precharge Delay
This controls the number of DRAM clocks for RAS minimum. Configuration options: [8 Clocks], [7 Clocks], [6 Clocks], and [5 Clocks].
DRAM Burst Length
DRAM Burst length can be set as [8] or [4].
Init. Graphic Adapter Priority
This allows you to select [Onboard/AGI/PCI], [AGI/PCI/Onboard], and [PCI/
AGI/Onboard] as the initial graphics adapter priority. The default vaule is
[PCI/AGI/Onboard].
Internal Graphics Mode Select
This allows you to select the size of share memory for onboard VGA. If
larger size of share memory is selected, onboard VGA will get better
resolution under DOS.
OnBoard LAN
This allows you to enable or disable the “OnBoard LAN” feature.
OnBoard AC’97 Audio
Select [Auto] or [Disabled] for the onboard AC’97 Audio feature.
OnBoard MC’97 Modem
Select [Auto] or [Disabled] for the onboard MC’97 Modem feature.
28
3.3.3 ACPI Configuration
BIOS SETUP UTILITY
Advanced
ACPI Configuration
Suspend To RAM
[Disabled]
Restore on AC / Power Loss
Ring-In Power On
PCI Devices Power On
PS / 2 Keyboard Power On
RTC Alarm Power On
[Power Off]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
Select auto-detect or
disable the STR
feature.
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
Suspend to RAM
Use this item to select whether to auto-detect or disable the Suspend-toRAM feature. Select [Auto] will enable this feature if the OS supports it.
Restore on AC/Power Loss
Use this item to set the power state after an unexpected AC/power loss. If
[Power Off] is selected, the AC/power remains off when the power
recovers. If [Power On] is selected, the AC/power resumes and the system starts to boot up when the power recovers.
Ring-In Power On
Use this item to enable or disable Ring-In signals to turn on the system from
the power-soft-off mode.
PCI Devices Power On
Use this item to enable or disable PCI devices to turn on the system from the
power-soft-off mode.
PS/2 Keyboard Power On
Use this item to enable or disable PS/2 keyboard to turn on the system from
the power-soft-off mode.
RTC Alarm Power On
Use this item to enable or disable RTC (Real Time Clock) to power on the
system.
29
3.3.4 IDE Configuration
BIOS SETUP UTILITY
Advanced
IDE Configuration
OnBoard IDE Operate Mode
OnBoard IDE Controller
Primary IDE Master
Primary IDE Slave
Secondary IDE Master
Secondary IDE Slave
SATA1
SATA2
[Enhanced Mode]
[Both]
[Hard Disk]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
Set [Compatible Mode]
when both Legacy OS
(MS-DOS, Win Me / 98SE)
and SATA device
are used.
Set [Enhanced Mode]
when Native OS
(Win 2000 / XP)
is used.
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
OnBoard IDE Operate Mode
Please select [Compatible Mode] when you install legacy OS (Windows
ME / 98SE) into SATA device. If you install legacy OS into IDE HDD while
SATA devices are used, you also need to select [Compatible Mode].
If native OS (Windows 2000 / XP) is installed into SATA device, please
select [Enhanced Mode]. You also need to select [Enhanced Mode]
while native OS is installed into IDE HDD and SATA devices are used.
If you do not install any SATA device, please also select [Enhanced Mode]
no matter you use legacy OS or native OS for the system.
Please note that the following options will be varied depending on the
“OnBoard IDE Operate Mode” ([Compatible Mode] or [Enhanced
Mode]) that you selected.
When [Enhanced Mode] is selected:
OnBoard IDE Controller
You may enable either the primary IDE channel or the secondary IDE channel.
Or you may enable both the primary and the secondary IDE channels by
selecting [Both]. Set to [Disabled] will disable the both. Configuration options:
[Disabled], [Primary], [Secondary], [Both].
When [Compatible Mode] is selected
Combined Mode Option
It allows you to select between [Pri IDE + SATA] and [SATA + Sec IDE]. If
it is set to [Pri IDE + SATA], then the secondary IDE will not work. Likewise,
if it is set to [SATA + Sec IDE], then the primary IDE will not work.
Because Intel® ICH5 south bridge only supports four IDE devices
under legacy OS (Windows ME / 98SE), you have to choose either
[Pri IDE + SATA] or [SATA + Sec IDE] when the installed SATA device
is used with legacy OS.
30
IDE Device Configuration
You may set the IDE configuration for the device that you specify. We will
use the “Primary IDE Master” as the example in the following instruction,
which can be applied to the configurations of “Primary IDE Slave”, “Secondary IDE Master”, “Secondary IDE Slave”, “SATA1” and “SATA2” as
well.
BIOS SETUP UTILITY
Advanced
Primary IDE Master
Device
Vendor
Size
LBA Mode
Block Mode
PIO Mode
Async DMA
Ultra DMA
S.M.A.R.T.
:Hard Disk
:ST340014A
:40.0 GB
:Supported
:16Sectors
:4
:MultiWord DMA-2
:Ultra DMA-5
:Supported
Type
LBA/Large Mode
Block (Multi-Sector Transfer)
PIO Mode
DMA Mode
S.M.A.R.T.
32Bit Data Transfer
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Disabled]
[Disabled]
Select the type
of device connected
to the system.
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
TYPE
Use this item to configure the type of the IDE device that you specify.
Configuration options: [Not Installed], [Auto], [CD/DVD], and [ARMD].
[Not Installed]: Select [Not Installed] to disable the use of IDE device.
[Auto]: Select [Auto] to automatically detect the hard disk drive.
After selecting the hard disk information into BIOS, use a disk
utility, such as FDISK, to partition and format the new IDE hard
disk drives. This is necessary so that you can write or read
data from the hard disk. Make sure to set the partition of the
Primary IDE hard disk drives to active.
[CD/DVD]: This is used for IDE CD/DVD drives.
[ARMD]: This is used for IDE ARMD (ATAPI Removable Media Device),
such as MO.
LBA/Large Mode
Use this item to select the LBA/Large mode for a hard disk > 512 MB under
DOS and Windows; for Netware and UNIX user, select [Disabled] to
disable the LBA/Large mode.
31
Block (Multi-Sector Transfer)
The default value of this item is [Auto]. If this feature is enabled, it will
enhance hard disk performance by reading or writing more data during
each transfer.
PIO Mode
Use this item to set the PIO mode to enhance hard disk performance by
optimizing the hard disk timing.
DMA Mode
DMA capability allows the improved transfer-speed and data-integrity for
compatible IDE devices.
S.M.A.R.T.
Use this item to enable or disable the S.M.A.R.T. (Self-Monitoring, Analysis,
and Reporting Technology) feature. Configuration options: [Disabled], [Auto],
[Enabled].
32-Bit Data Transfer
Use this item to enable 32-bit access to maximize the IDE hard disk data
transfer rate.
3.3.5 PCIPnP Configuration
BIOS SETUP UTILITY
Advanced
Value in units of PCI
clocks for PCI device
latency timer
register.
PCI / PnP Configuration
PCI Latency Timer
PCI IDE BusMaster
[32]
[Enabled]
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
PCI Latency Timer
The default value is 32. It is recommended to keep the default value unless
the installed PCI expansion cards’ specifications require other settings.
PCI IDE BusMaster
Use this item to enable or disable the PCI IDE BusMaster feature.
32
3.3.6 Floppy Configuration
In this section, you may configure the type of your floppy drive.
BIOS SETUP UTILITY
Advanced
Floppy Configuration
[1.44 MB 31 2"]
[Disabled]
Floppy A
Floppy B
Select the type of
floppy drive
connected to the
system.
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
3.3.7 Super IO Configuration
BIOS SETUP UTILITY
Advanced
Configure Super IO Chipset
OnBoard Floppy Controller
Serial Port Address
Infrared Port Address
Parallel Port Address
Parallel Port Mode
EPP Version
ECP Mode DMA Channel
Parallel Port IRQ
Allow BIOS to Enable
or Disable Floppy
Controller.
[Enabled]
[3F8 / IRQ4]
[Disabled]
[378]
[ECP + EPP]
[1.9]
[DMA3]
[IRQ7]
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
OnBoard Floppy Controller
Use this item to enable or disable floppy drive controller.
Serial Port Address
Use this item to set the address for the onboard serial port or disable it.
Configuration options: [Disabled], [3F8 / IRQ4], [2F8 / IRQ3], [3E8 / IRQ4],
[2E8 / IRQ3].
Infrared Port Address
Use this item to set the address for the onboard infrared port or disable it.
Configuration options: [Disabled], [2F8 / IRQ3], and [2E8 / IRQ3].
33
Parallel Port Address
Use this item to set the address for the onboard parallel port or disable it.
Configuration options: [Disabled], [378], and [278].
Parallel Port Mode
Use this item to set the operation mode of the parallel port. The default
value is [ECP+EPP]. If this option is set to [ECP+EPP], it will show the EPP
version in the following item, “EPP Version”. Configuration options:
[Normal], [Bi-Directional], and [ECP+EPP].
EPP Version
Use this item to set the EPP version. Configuration options: [1.9]
and [1.7].
ECP Mode DMA Channel
Use this item to set the ECP mode DMA channel. Configuration
options: [DMA0], [DMA1], and [DMA3].
Parallel Port IRQ
Use this item to set the IRQ for the parallel port. Configuration options:
[IRQ5] and [IRQ7].
34
3.3.8 USB Configuration
BIOS SETUP UTILITY
Advanced
USB Configuration
To enable or disable
the onboard USB
controllers.
USB Devices Enabled :
None
USB Controller
USB 2.0 Support
Legacy USB Support
[Enabled]
[Enabled]
[Disabled]
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
USB Controller
Use this item to enable or disable the use of USB controller.
USB 2.0 Support
Use this item to enable or disable the USB 2.0 support.
Legacy USB Support
Use this item to enable or disable the support to emulate legacy I/O
devices such as mouse, keyboard,... etc. Or you may select [Auto] so
that the system will start to auto-detect; if there is no USB device
connected, “Auto” option will disable the legacy USB support.
3.4 Hardware Health Event Monitoring Screen
In this section, it allows you to monitor the status of the hardware on your system,
including the parameters of the CPU temperature, motherboard temperature, CPU fan
speed, chassis fan speed, and the critical voltage.
Main
Advanced
BIOS SETUP UTILITY
Boot
H/W Monitor
Security
Hardware Health Event Monitoring
CPU Temperature
M / B Temperature
: 45 C / 98 F
: 31 C / 87 F
CPU Fan Speed
Chassis Fan Speed
: 2463 RPM
: N/A
Vcore
+ 3.30V
+ 5.00V
+ 12.00V
:
:
:
:
1.384V
3.306V
5.067V
11.890V
F1
F9
F10
ESC
Select Screen
Select Item
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
35
Exit
3.5 Boot Screen
In this section, it will display the available devices on your system for you to configure the boot settings and the boot priority.
Main
Advanced
BIOS SETUP UTILITY
H/W Monitor
Boot
Boot Settings
Security
Exit
Configure Settings
during System Boot.
Boot Settings Configuration
Boot Device Priority
Hard Disk Drives
Removable Drives
CD / DVD Drives
Enter
F1
F9
F10
ESC
Select Screen
Select Item
Go to Sub Screen
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
3.5.1 Boot Settings Configuration
BIOS SETUP UTILITY
Boot
Boot Settings Configuration
Boot From Network
Bootup Num-Lock
To enable or disable the
boot from network feature.
[Disabled]
[On]
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
Boot From Network
Use this item to enable or disable the Boot From Network feature.
Boot Up Num-Lock
If this item is set to [On], it will automatically activate the Numeric Lock
function after boot-up.
36
3.5.2 Boot Device Priority
In this section, you may specify the boot sequence from the available devices
in your system.
BIOS SETUP UTILITY
Boot
Boot Device Priority
[1st FLOPPY DRIVE]
[HDD: PM-MAXTOR 6L08]
[CD / DVD]
1st Boot Device
2nd Boot Device
3rd Boot Device
Specifies the boot
sequence from the
available devices.
A device enclosed in
parenthesis has been
disabled in the
corresponding type
menu.
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
Likewise, you may also specify the boot sequence from the available devices
for the hard disk drives, the removable drives, and the CD/DVD drives.
3.6 Security Screen
In this section, you may set or change the supervisor/user password for the system.
For the user password, you may also clear it.
Main
Advanced
BIOS SETUP UTILITY
H/W Monitor
Boot
Security Settings
Supervisor Password
User Password
Security
Exit
Install or Change the
password.
: Not Installed
: Not Installed
Change Supervisor Password
Change User Password
Clear User Password
Enter
F1
F9
F10
ESC
Select Screen
Select Item
Change
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
37
3.7 Exit Screen
Main
Advanced
BIOS SETUP UTILITY
H/W Monitro
Boot
Exit Options
Security
Exit
Exit system setup
after saving the
changes.
Save Changes and Exit
Discard Changes and Exit
Discard Changes
F10 key can be used
for this operation.
Load Optimal Defaults
Enter
F1
F9
F10
ESC
Select Screen
Select Item
Go to Sub Screen
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
Save Changes and Exit
When you select this option, it will pop-out the following message, “Save
configuration changes and exit setup?” Select [OK] to save the changes
and exit the BIOS SETUP UTILITY.
Discard Changes and Exit
When you select this option, it will pop-out the following message, “Discard changes and exit setup?” Select [OK] to exit the BIOS SETUP UTILITY
without saving any changes.
Discard Changes
When you select this option, it will pop-out the following message, “Discard changes?” Select [OK] to discard all changes.
Load Optimal Defaults
When you select this option, it will pop-out the following message, “Load
optimal defaults?” Select [OK] to load the default values for all the setup
configurations.
38
Chapter 4 Software Support
4.1
Install Operating System
This motherboard supports various Microsoft® Windows® operating systems: 98 SE / ME / 2000
/ XP. Because motherboard settings and hardware options vary, use the setup procedures in this
chapter for general reference only. Refer to your OS documentation for more information.
4.2
Support CD Information
The Support CD that came with the motherboard contains necessary drivers and useful utilities
that enhance the motherboard features.
4.2.1 Running The Support CD
To begin using the support CD, insert the CD into your CD-ROM drive. The CD automatically displays the Main Menu if “AUTORUN” is enabled in your computer. If the Main
Menu did not appear automatically, locate and double click on the file “ASSETUP.EXE”
from the BIN folder in the Support CD to display the menus.
4.2.2 Drivers Menu
The Drivers Menu shows the available devices drivers if the system detects installed
devices. Please install the necessary drivers to activate the devices.
4.2.3 Utilities Menu
The Utilities Menu shows the applications software that the motherboard supports. Click on
a specific item then follow the installation wizard to install it.
4.2.4 ASRock “PC-DIY Live Demo” Program
ASRock presents you a multimedia PC-DIY live demo, which shows you how to install
your own PC system step by step. You can find the file through the following path:
..\ MPEGAV \ AVSEQ01.DAT
To see this demo program, you can run Microsoft® Media Player® to play the file.
4.2.5 “LGA 775 CPU Installation Live Demo” Program
This motherboard is equipped with Intel LGA 775 socket, which is a new CPU socket
interface that Intel has released. Since it has several tiny pins, whcih are easily to be
damaged by improper handling, ASRock sincerely presents you a clear installation guide
through this “LGA 775 CPU Installation Live Demo”. We hope you may check this live
demo program before you start the installation of LGA 775 CPU in order to reduce the risks
of CPU and motherboard damages caused by any improper handling. To see this Live
Demo, you can run Microsoft® Media Player® to play the file. You may find this Live Demo
in the motherboard’s Support CD through the following path:
..\ MPEGAV \ LGA775INST.DAT
4.2.6 Contact Information
If you need to contact ASRock or want to know more about ASRock, welcome to visit
ASRock’s website at http://www.asrock.com; or you may contact your dealer for further
information.
39