Asus A4D Laptop User Manual

M A N U FAC T U R I N G , I N C.
Intermediate Frame Snowthrowers
Initial setup
This Dealer Setup Instruction covers the following products:
Intermediate Frame Snowthrowers
Mfg. No.
1695302
1695311
1695410
1695313
1695314
1695411
Description
SMI I1924E, 9GT, B&S 24
SMI I1924EX, 9GT, B&S 24 (CE)
SMI I1924EX, 9GT, B&S 24 (CE)
SNP I1924E, 9GT, B&S 24
SNP I1924EX, 9GT, B&S 24 (CE)
SNP I1924EX, 9GT, B&S 24 (CE)
Briggs & Stratton Yard Power Products Group
Copyright © 2007 Briggs & Stratton Corporation
Milwaukee, WI USA. All Rights Reserved
09/2007
Form No. 1735249
TP 300-4681-01-IW-SN
Intermediate Frame Snowthrowers
SAFETY RULES
Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control
of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment.
The triangle
in text signifies important cautions or warnings which must be followed.
GENERAL OPERATION
operate the unit safely enough to protect themselves and
others from injury.
• All operators should seek and obtain professional and practical instruction.
• Always wear substantial footwear and appropriate winter
clothing. Wear foot-ware that improves traction on slippery
slopes. DO NOT wear long scarves or loose clothing that
could become entangled in moving parts.
• Before using, always visually check that all hardware is
present, in-tact, and secure. Replace worn or damaged
parts.
• Never operate the machine with defective guards, or without safety protective devises in place.
• Stop engine before: refuelling, removing an attachment,
making adjustments (unless the adjustment can be made
from the operator’s position).
• Follow the manufacturer’s recommendation for wheel
weights or counterweights.
• Adjust skid shoe height to clear gravel or crushed rock surfaces.
• Do not touch snowthrower parts which may be hot from
operation. Allow such parts to cool before attempting to
service the unit.
CLEARING A CLOGGED DISCHARGE CHUTE
Hand contact with the rotating impeller inside the discharge
chute is the most common cause of injury associated with
snowthrowers. Always use a clean out tool, not your hands. to
clean out the discharge chute.
To clear the chute:
1. SHUT OFF THE ENGINE.
2. Wait 10 seconds to be sure the impeller blades have
stopped rotating.
3. Always use a clean out tool, not your hands.
• Read, understand, and follow all instructions in the
manual and on the unit before starting.
• Only allow responsible adults, who are familiar with the
instructions, to operate the unit (local regulations can
restrict operator age).
• Clear the area of objects such as rocks, toys, wire, etc.,
which could be picked up and thrown.
• Be sure the area is clear of other people. Stop unit if anyone enters the area.
• Always look down and behind before and while travelling in
reverse.
• Be aware of the discharge direction and do not point it at
anyone. Do not point the discharge at glass enclosures,
automobiles, or windows.
• Disengage all clutches (release drive and auger control
levers) before starting the engine.
• Never leave a running unit unattended. Always disengage
the auger and traction controls, stop engine, and remove
keys.
• Stop engine before unclogging chute.
• Operate only in daylight or good artificial light.
• Do not operate the unit while under the influence of alcohol
or drugs.
• Watch for traffic when operating near or crossing roadways.
• Use extra care when loading or unloading the unit into a
trailer or truck.
• Keep in mind the operator is responsible for accidents
occurring to other people or property.
• Data indicates that operators, age 60 years and above, are
involved in a large percentage of power equipment-related
injuries. These operators should evaluate their ability to
SLOPE OPERATION
Do
• See your authorized dealer for recommendations counterweights to improve stability.
• Travel up and down slopes, not across.
• Remove obstacles such as rocks, tree limbs, etc.
• Watch for holes, ruts, or bumps. Uneven terrain could overturn the unit. Snow can hide obstacles.
• Use slow speed. Tires may lose traction on slopes. Choose
a low gear so that you will not have to stop or shift while on
the slope.
• Keep all movement on the slopes slow and gradual. Do not
make sudden changes in speed or direction.
• Always keep unit in gear especially when traveling downhill.
Do Not
• Do not start or stop on a slope. If tires lose traction, disengage the auger and proceed slowly straight down the
slope.
• Do not turn on slopes unless necessary, and then, turn
slowly and gradually downhill, if possible.
• Do not operate near drop-offs, ditches, or embankments.
The unit could suddenly turn over if a wheel is over the
edge of a cliff or ditch, or if an edge caves in.
• Do not operate on wet surfaces. Reduced traction could
cause sliding.
• Do not shift to neutral and coast down hills.
WARNING
Never operate on slopes greater than 17.6 percent (10°) which
is a rise of 3-1/2 feet (106 cm) vertically in 20 feet (607 cm)
horizontally.
When operating on slopes use additional wheel weights or
counterweights. See your dealer to determine which weights
are available and appropriate for your unit.
Select slow ground speed before driving onto slope. Travel UP
and DOWN the slope, never across the face, use caution when
changing directions and DO NOT START OR STOP ON
SLOPE.
Slopes are a major factor related to loss-of-control and tip-over
accidents, which can result in severe injury or death. All slopes
require extra caution. If you cannot back up the slope or if you feel
uneasy on it, do not operate on it.
EMISSIONS
• Engine exhaust from this product contains chemicals
known, in certain quantities, to cause cancer, birth defects,
or other reproductive harm.
• Look for the relevant Emissions Durability Period and Air
Index information on the engine emissions label.
TP 300-4681-01-IW-SN
2
09/2007
Intermediate Frame Snowthrowers
Table of Contents
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1. Uncrate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Check Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Install Handles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4. Secure Dash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5. Install Chute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
6. Install Chute Rotator Crank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
7. Tube Handle Levers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
8. Auger Shaft Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
9. Auger Drive Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
10. Auger Shaft Shear Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
11. Deflector Hinge Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
12. Axles and Control Lever Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
13. Spout Rotator Lubrication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
14. Hand Control Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
15. Engine Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Perform Safety Checks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Check Engine Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Check Snowthrower Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Check Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Auger Drive Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Traction Drive Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Scraper Bar & Skid Shoe Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Belt Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Belt Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Auger Drive belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Traction Drive Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
09/2007
3
TP 300-4681-01-IW-SN
Intermediate Frame Snowthrowers
1
(2) x
2
TP 300-4681-01-IW-SN
Size
PSI
bar
15 x 5.0-6
20
1,38
16 x 4.8-8
14
,96
4
09/2007
Intermediate Frame Snowthrowers
3
B
D
A
B
C
A
D
A
C
5/16-18
5/16-18 x 2
B
D
5/16-18 x 2-3/4
5/16
4
7 Nm
5 lb-ft
09/2007
5
TP 300-4681-01-IW-SN
Intermediate Frame Snowthrowers
5
B
A
5/16-18 x 1-1/2
B
5/16-18
A
6
A
D
C
B
TP 300-4681-01-IW-SN
6
09/2007
Intermediate Frame Snowthrowers
7
1
1
2
2
3
8
09/2007
9
7
TP 300-4681-01-IW-SN
Intermediate Frame Snowthrowers
10
11
TP 300-4681-01-IW-SN
12
8
09/2007
Intermediate Frame Snowthrowers
09/2007
13
14
15
16
9
TP 300-4681-01-IW-SN
Intermediate Frame Snowthrowers
Perform
Safety Checks
F
E
B
A
Check Engine Controls
C
1. Make sure all safety guards are in place and all nuts,
bolts, clips, cotter pins and wires are secure.
2. Check to make sure spark plug wire is attached.
3. Check all controls for proper operation:
D
a. The engine should stop when the key is removed.
b. The throttle should control the engine speed and
stop the engine when moved to the STOP position.
G
c. The fuel shut-off valve should stop the flow of fuel
to the engine
Snow
Series
d. The recoil starter or electric starter (if equipped)
should crank the engine when activated.
4. Check the engine area for oil or gasoline leaks.
Correct any problems in accordance with the engine
manufacturers instructions.
TP 300-4681-01-IW-SN
Figure 1. Engine Controls
A. Electric Start Button (Select Models)
B. Fuel Valve (Select Models)
C. Starter Handle
D. Primer Button
E. Engine Key
F. Choke Knob
G. Stop Switch
10
09/2007
Intermediate Frame Snowthrowers
Perform
Safety Checks
E
Check Snowthrower Controls
1. Check the skid shoes to make sure they are set at the
desired height. Adjust if necessary.
2. Check the traction drive control (B, Figure 2).
Snowthrower motion should stop when the control is
released.
B
C
3. Check the auger control (C). Auger movement should
stop when the control is released.
4. Check the manual chute direction control (D) for proper operation. The discharge chute should rotate freely
in both directions.
5. Check the deflector for proper operation. The
deflector should pivot freely up and down when the
chute deflector knob (E) is loosened.
D
6. Check the speed selector (A) for smooth operation.
The control must move freely into each speed position gate and remain in position when released.
A
Figure 2. Controls (from operator’s position)
A. Speed Selector
B. Traction Control
C. Auger Engage Control
D. Chute Rotator Control
E. Deflector Control
If controls do not function properly, perform the
appropriate adjustment as shown in the
Adjustment Section.
7. The auger is secured to the shaft by shear pins,
which will break if the auger strikes an object. Extra
shear pins are provided. Keep these pins in the compartment on the belt cover. Lubricate the auger shaft.
Check Operations
1. With engine at full speed, engage the auger control
and release. Do this ten (10) times. Auger should
come to a complete stop within five seconds each
time. If not, perform Auger Adjustments.
3. Engage traction control and release. Do this ten
times. Unit should come to a complete stop each
time. If it does not, perform the Traction Drive
Adjustments.
4. Remove the engine key. The engine must stop.
5. Move the throttle to STOP. The engine must stop.
09/2007
11
TP 300-4681-01-IW-SN
Intermediate Frame Snowthrowers
Auger Drive
Adjustment
A
D
WARNING
E
Do not over-tighten, as this may lift the lever and
cause auger drive to be engaged without
depressing the Auger Control.
F
1.With the drive lever released, the hook (B, Figure 3)
should barely touch the lever (C) without raising it.
There can be a maximum 1/32” clearance as shown.
2. To adjust, loosen nut (D) by holding the adjusting
flats (A) and turning nut (D). Turn adjustment flats
and hold screw. The adjustment screw (E) is a
phillips screw and the head can be held or turned by
inserting a screwdriver through the spring (F).
3. Hold adjusting flats (A) and tighten nut (D).
4. Start unit and check auger. Auger must not be
engaged unless auger control is depressed.
5. With engine running, fully depress auger control, the
auger should engage and run normally.
1/32” (.8 mm)
C
B
Figure 3. Auger Drive Adjustment
A. Adjusting Flats
B. Spring Hook
C. Lever
D. Adjustment Nut
E. Adjustment Screw
F. Spring
6. Release auger control. Auger must stop within 5
seconds.
7. If auger does not operate properly, stop engine and
recheck drive linkage adjustments.
8. If auger linkage is properly adjusted, auger drive belt
tension may require adjustment. See adjusting the
auger belt in this section of the manual
TP 300-4681-01-IW-SN
12
09/2007
Intermediate Frame Snowthrowers
Run-In Adjustment
WARNING
ALL MODELS
Do not over-tighten, as this may cause traction
drive to engage without depressing the traction
drive control (arm must remain in down position).
1. After 5 hours of use, check for proper adjustment.
Readjust clutch cable if necessary by increasing tension on cable. A small amount of arm movement is
permissible if unit passes operating checks described
in the Warning above.
Verify that the cables are not over-tightened: With
speed selector in position 1 and traction drive
control fully released, push snowthrower forward.
The unit should move forward freely.
WARNING
If unit does not move forward freely, the cable has
been over-tightened. To remedy, loosen tension
on clutch cable slightly, and recheck.
Gasoline is highly flammable and must be
handled with care. Drain gasoline outdoors. Never
drain the tank when the engine is still hot from
recent operation. Do not allow open flame,
smoking or matches in the area. Avoid over-filling
and wipe up any spills.
TRACTION DRIVE ADJUSTMENT
Initial Adjustment
2. Remove the gas from the gas tank.
1. With the drive lever released there should be slack in
the cable when moved slightly from side to side.
3. Disconnect the spark plug wire.
4. Stand snowthrower on the front of the auger housing
(C, Figure 5).
2. To adjust tension on the cable slide the cable boot
(A, Figure 4) off the cable adjustment bracket (D).
5. Remove the capscrews (A) on each side of the bottom panel (B).
3. Move the “Z” hook (C) from the cable adjustment
bracket (D) to a different adjustment hole. The cable
should have slack. The cable should have no tension
or load.
6. Remove the bottom panel (B).
Note: If the cable is too slack the unit will not drive. If the
cable is too tight the drive will be engaged without pushing the handle down.
A
4. Slide the cable boot (A) over the cable adjustment
bracket.
A
C
B
Figure 5. Bottom Cover
A. Capscrews
B. Bottom Panel
C. Auger Housing
A
B
B
C
D
C
Figure 4. Traction Drive Cable Adjustment
A. Cable Boot
B. Traction Drive Cable
C. “Z” Hook
D. Cable Adjustment Bracket
09/2007
13
TP 300-4681-01-IW-SN
Intermediate Frame Snowthrowers
7. Loosen shift lever nuts (B, Figure 6), and position the
shift speed lever (A) in the lowest forward speed.
A
B
Figure 6. Shift Lever Adjustment
A. Shift Lever
B. Nuts, 1/4-20
8. Note the position of the friction wheel (A, Figure 7).
The correct distance from the right side of the friction
wheel to the outside of the frame is 4-5/16” (10.95
cm). If the friction wheel is not in the correct position,
adjust as follows.
9. Move the friction wheel (A, Figure 7) to the correct
distance, 4-5/16” (10.95 cm).
10. Tighten the 1/4-20 shift lever nuts (B, Figure 6) to 60
lb-in. (6,8 Nm).
11. Check that the snowthrower operates in R1. If not
follow procedures 1-10 and readjust as necessary.
Scraper Bar &
Skid Shoe Adjustment
On smooth surfaces such as concrete or asphalt, the
scraper bar should scrape the surface. On surfaces such
as gravel, the scraper bar should be high enough so that
it will not pick up gravel or debris.
The height of the scraper bar is controlled by raising or
lowering the Skid Shoes (See Figure 8).
1. To raise the scraper bar height, rest the scraper bar on
a strip of wood equal in thickness to the desired height.
2. Make sure the scraper bar is parallel to the ground
surface.
3. Loosen the skid shoe nuts and let the skid shoes drop
to the surface.
4. Tighten the nuts, making sure the Skid Shoes are
adjusted equally and are parallel to the surface.
5. To lower the height of the scraper bar, raise the Skid
Shoes.
6. If the scraper bar becomes worn, it can be adjusted
by loosening the nuts and bolts attaching it to the
snowthrower, making the adjustment, and tightening
the hardware. It may also be replaced by removing
the mounting nuts and bolts attaching it to the
snowthrower.
12. Install the bottom panel (B, Figure 5) and tighten the
capscrews (A).
A
C
A
B
4-5/16”
(10.95cm)
B
Figure 8. Skid Shoe Adjustment
A. Scraper Bar
B. Skid Shoe
C. Nuts
Figure 7. Friction Disc Measurement
A. Friction Wheel
B. Frame
TP 300-4681-01-IW-SN
14
09/2007
Intermediate Frame Snowthrowers
Belt Adjustment
Auger Drive Belt
B
If your snowthrower will not discharge snow, check the
control cable adjustment. If it is correct, then check the
condition of the auger drive belt. If it is damaged or
loose,replace it (see Belt Replacement in this section of
the manual).
1. Disconnect spark plug wire.
2. Loosen screw (B, Figure 9) from belt cover (A).
Remove belt cover (A).
B
3. Loosen nut (D, Figure 10) on auger idler pulley (B)
and move auger idler pulley towards belt about 1/8
inch (3mm).
A
Figure 9. Belt Cover
A. Belt Cover
B. Screws
4. Tighten nut (D).
5. Engage auger drive clutch. Check tension on belt
(opposite idler pulley). Belt should deflect about 1/2
inch (12.5 mm) with moderate pressure see Figure
11). You may have to move the idler pulley more
than once to obtain the correct tension.
A
E
B
6. Reinstall belt cover (A, Figure 9) securing with
screws (B).
D
7. Whenever belts are adjusted or replaced, the auger
drive or traction drive controls will need to be
adjusted. (see Auger Drive or Traction Drive
Adjustment in this section of the manual).
8. Attach the spark plug wire.
1/2” (12.5mm)
Deflection
C
9. Auger must stop within 5 seconds.
Figure 10. Auger Belt Deflection
A. Engine Drive Pulley
B. Idler Pulley (Engaged Position)
C. Auger Drive Pulley
D. Nut
E. Auger Belt
Traction Drive Belt
The traction drive belt has constant spring pressure and
does not require an adjustment. If the traction drive belt
is slipping,replace the belt. See Belt Replacement.
Note: After adjustments are complete, make sure the
drive disengages when released.
09/2007
15
TP 300-4681-01-IW-SN
Intermediate Frame Snowthrowers
Belt Replacement
A
B
F
Auger Drive Belt
The drive belts are of special construction and must be
replaced with original factory replacement belts available
from your nearest authorized service center. Some
steps require the assistance of a second person. If the
auger drive belt is damaged, the snow thrower will not
discharge snow. Replace the damaged belt as follows.
C
L
D
K
E
1. Disconnect the spark plug wire.
A
2. Loosen the capscrews (A, Figure 11) on each side of
the bottom panel (B).
J
G
3. Remove the bottom panel (B).
I
H
A
A
C
B
Figure 11. Bottom Cover
A. Capscrews
B. Bottom Panel
C. Auger Housing
Figure 12. Pulleys and Belts
A. Traction Drive Belt
B. Belt Guide
C. Auger Drive Pulley, Engine
D. Auger Drive Belt
E. Traction Drive Spring
F. Traction Drive Pulley, Engine
G. Traction Drive Pulley
H. Impeller Pulley
I. Swing Plate Axle Rod
J. “E”-Ring
K. Auger Idler Pulley
L. Traction Drive Idler Pulley
4. Loosen screw (B, Figure 8) from belt cover (A).
Remove belt cover (A).
8. Remove the 5/16 flange lock nut (B, Figure 13)
securing the rotator cover (A).
5. Loosen the belt guide (B, Figure 12). Pull the belt
guide away from the auger drive pulley (A).
B
6. Pull the auger idler pulley (K) away from the auger
drive belt (D) and slip the belt off of the idler.
A
7. Remove the auger drive belt (D) from the engine pulley. To remove the auger drive belt (D), the auger
drive pulley (C) may have to be partially rotated.
Figure 13. Rotator Cover Removal
A. Cover
B. Nut, flange, lock 5/16-18
TP 300-4681-01-IW-SN
16
09/2007
Intermediate Frame Snowthrowers
B
A
A
Figure 14. Rotator Shaft Removal
A. Pin, Hair
B. Shaft
A
C
Figure 16. Chute and Rotator Removal
A. Chute and Rotator
B
D
A
Figure 15. Offset Tube (Lower) Removal
A. Nuts, KEPS, hex, 5/16-18
B. Bolts, Carriage, 5/16 x 1-1/2
C. Tube, Offset
D. Bracket, tube support
B
9. Remove hair pin (A, Figure 14) and slide rod (B)
backward about 3 inches (until shaft separates from
the worm drive).
D
10. Remove two 5/16-18 KEPS hex nuts (A, Figure 15),
and two 5/16-18 x 1-1/2 carriage bolts (B) securing
the offset tube (C) to the tube support bracket (D).
C
Figure 17. Frame and Axle Housing Splitting
A. Upper Capscrews
B. Lower Capscrews
C. Auger Housing
D. Frame
11. Lift the Chute and rotator (A, Figure 16) off of the
auger housing.
12. Remove the upper four capscrews (A, Figure 17) that
hold together the auger housing (C) and the frame
(D). Loosen the lower two capscrews (B). The auger
housing (C) and the frame (D) can now be split apart
for removal of the belt.
NOTE: To assemble the auger housing to the frame,
have someone hold the auger clutch lever in the
ENGAGED position. This will move the idler arm and
pulley enough to allow the auger drive pulley to move
back into position.
13. Remove the old auger drive belt (D, Figure 12) from
the impeller pulley . Replace the auger drive belt with
an original factory replacement belt available from an
authorized service center.
15. Assemble the auger housing (C, Figure 17) to the
frame with the four upper taptite screws (A) that were
removed in step 12. Tighten the two lower taptite
screws (B). Tighten all taptite screws to
40-50 lb-in (4,5-5,6 Nm).
14. Install the new auger drive belt (D) onto the impeller
pulley.
09/2007
16. Attach chute and offset tube previously removed
(Figure 15 and 16. Tighten all KEPS nuts to 11 lb-ft
(15 Nm).
17
TP 300-4681-01-IW-SN
Intermediate Frame Snowthrowers
Traction Drive Belt
If the snow thrower will not move forward, check the traction drive belt for wear or damage. If the traction drive
belt is worn or damaged, replace the belt as follows.
1. Disconnect the spark plug wire.
2. Remove the auger drive belt. See “Belt Replacement”
in this section.
3. Remove the traction drive spring (E, Figure 12).
B
4. Remove the e-ring (J, Figure 12) from one end of the
swing plate axle rod (I).
5. Remove the swing plate axle rod (I) to allow the
swing plate (A, Figure 12) to pivot forward.
6. Remove the old traction drive belt (A) from the traction drive pulley (G) and from the traction drive pulley
(F). Replace the traction drive belt (A) with an original factory replacement belt available from an
authorized Dealer.
A
Figure 18. Traction Belt Change
A. Swing Plate
B. Alignment Tabs
7. Install the new traction drive belt (A) onto the traction
drive pulley (G) and onto traction drive pulley (F).
8. Make sure the traction drive idler pulley (L) is properly aligned with the traction drive belt (A).
17. Slide spout rotator rod (B, Figure 14) into worm gear,
and secure with hair pin (A).
9. Install the swing plate axle rod (I) and secure with the
e-ring (J) removed earlier.
18. Install rotator cover (A, Figure 13) and secure with
5/16-18 flange lock nut (B). Tighten nut to 11 lb-ft (15
Nm).
10. The bottom of the swing plate (A, Figure 18) must be
positioned between the alignment tabs (B). Make
sure the swing plate is properly secured.
19. Install the auger drive belt (D, Figure 12) onto the
impeller pulley (H).
NOTE: If the drive will not engage after the traction drive
belt has been replaced, then check to make sure that the
swing plate is positioned between the alignment tabs.
20. Slip the auger drive belt (D) under the idler pulley (K).
21. Adjust the auger drive belt. See “Belt Adjustment:
Auger Drive Belt” in the Adjustment section.
22. Adjust the belt guide. See “Belt Adjustment” in this
section.
23. Install the belt cover (A, Figure 9). Tighten 1/4-20
screws (B) to 25-35 lb-in (2,8-3,9 Nm).
Note: Caution must be taken when tightening the screws
that secure the belt cover. Over tightening the screws
will deform the plastic.
11. Attach the traction drive spring (E, Figure 12).
12. Install and adjust the auger drive belt. See Belt
Replacement in this section of the manual.
13. Adjust the belt guide. See Belt Adjustment in this
section of the manual.
14. Install the bottom panel (B, Figure 11). Tighten 1/420 screws to 25-35 lb-in (2,8-3,9 Nm).
15. Install the belt cover (A, Figure 9). Tighten 1/4-20
screws (B) to 25-35 lb-in (2,8-3,9 Nm).
24. Check the adjustment of the cables. See
“Adjustments - Auger Drive Adjustment and Traction
Drive Cable Adjustment” in the Adjustment section.
Note: Caution must be taken when tightening the screws
that secure the belt cover. Over tightening the screws
will deform the plastic.
25. Install the bottom panel (B, Figure 11). Tighten 1/420 screws to 25-35 lb-in (2,8-3,9 Nm).
16. Check the adjustment of the cables. See
Adjustments in this section of the manual.
26 Connect the spark plug wire.
17. Connect the spark plug wire.
TP 300-4681-01-IW-SN
18
09/2007
Download PDF

advertising