Asus ET2411 Personal Computer User Manual

E8806
December 2013
First Edition
LED projector
E-Manual
S1
COPYRIGHT AND WARRANTY INFORMATION
No part of this manual, including the products and software described in it, may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language in any form or by any means, except documentation kept by the purchaser for
backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or
altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2)
the serial number of the is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS,
ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN
IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
Products and corporate names appearing in this manual may or may not be registered
trademarks or copyrights of their respective companies, and are used only for identification or
explanation and to the owners’ benefit, without intent to infringe.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Copyright © 2013 ASUSTeK COMPUTER INC. All Rights Reserved.
LIMITATION OF LIABILITY
Circumstances may arise where because of a default on ASUS’ part or other liability, you are
entitled to recover damages from ASUS. In each such instance, regardless of the basis on which
you are entitled to claim damages from ASUS, ASUS is liable for no more than damages for
bodily injury (including death) and damage to real property and tangible personal property;
or any other actual and direct damages resulted from omission or failure of performing legal
duties under this Warranty Statement, up to the listed contract price of each product.
ASUS will only be responsible for or indemnify you for loss, damages or claims based in
contract, tort or infringement under this Warranty Statement.
This limit also applies to ASUS’ suppliers and its reseller. It is the maximum for which ASUS, its
suppliers, and your reseller are collectively responsible.
UNDER NO CIRCUMSTANCES IS ASUS LIABLE FOR ANY OF THE FOLLOWING: (1) THIRDPARTY CLAIMS AGAINST YOU FOR DAMAGES; (2) LOSS OF, OR DAMAGE TO, YOUR RECORDS
OR DATA; OR (3) SPECIAL, INCIDENTAL, OR INDIRECT DAMAGES OR FOR ANY ECONOMIC
CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS OR SAVINGS), EVEN IF ASUS, ITS
SUPPLIERS OR YOUR RESELLER IS INFORMED OF THEIR POSSIBILITY.
SERVICE AND SUPPORT
Visit our multi-language web site at http://support.asus.com
LED projector E-Manual
Table of Contents
About this manual.............................................................................................. 5
Conventions used in this manual................................................................ 6
Typography.......................................................................................................... 6
Multi-language versions................................................................................. 6
Safety precautions.............................................................................................. 7
Using your LED projector................................................................................ 7
Servicing and replacement of parts........................................................... 7
Caring for your LED projector....................................................................... 8
Proper disposal................................................................................................... 8
Chapter 1: Knowing your LED projector
Features................................................................................................................10
Top view.............................................................................................................10
Extended features...........................................................................................12
Flashlight...............................................................................................................12
Emergency light mode.....................................................................................13
Front view...........................................................................................................14
Rear view............................................................................................................15
Right side............................................................................................................17
Left side.............................................................................................................18
Bottom view......................................................................................................19
Chapter 2: Setting up
Operating your LED projector......................................................................22
1. Connect the LED projector to the power adapter...........................22
AC power cord requirements.........................................................................24
2. Connect the LED projector to your device........................................25
3. Press the power button............................................................................26
4. Open the lens cover and adjust the focus ring................................27
Screen size and projection distance table.................................................28
LED projector E-Manual
Chapter 3:Using the LED projector
Using your LED projector for the first time..............................................30
Operating the onscreen display menu......................................................31
Adjusting your LED projector's settings...................................................32
Onscreen display menu options..................................................................33
Volume .............................................................................................................33
Brightness..........................................................................................................33
Contrast.............................................................................................................34
Splendid.............................................................................................................34
When powered by battery only....................................................................35
Connected to a power outlet.........................................................................35
Aspect Ratio.......................................................................................................36
Projection Position..........................................................................................36
Setup .............................................................................................................37
Information........................................................................................................37
Turning off your LED projector.....................................................................38
Appendices
Federal Communications Commission Statement...............................40
Canadian Department of Communications Statement......................41
Global Environmental Regulation Compliance and Declaration . ..41
ASUS Recycling/Takeback Services............................................................41
Support PC Timings..........................................................................................42
HDMI (PC) .........................................................................................................42
HDMI (Video).....................................................................................................42
Specifications for S1 LED projector.............................................................43
LED projector E-Manual
About this manual
This manual provides information about the hardware and software
features of your LED projector through the following chapters:
Chapter 1: Knowing your LED Projector
This chapter details the parts of your LED projector and its
accompanying remote control.
Chapter 2: Setting up
This chapter shows you how to set up your LED projector and
use its parts for input device connection.
Chapter 3: Using the LED projector
This chapter describes the features of the LED projector’s control
panel buttons and how to use them to launch the functions of
your LED projector.
Appendices
This section includes safety notices for your LED projector.
LED projector E-Manual
Conventions used in this manual
To highlight key information in this manual, some text are presented
as follows:
IMPORTANT! This message contains vital information that must be
followed to complete a task.
NOTE: This message contains additional information and tips that
can help complete tasks.
WARNING! This message contains important information that must
be followed to keep you safe while performing tasks and prevent
damage to your LED projector's data and components.
Typography
Bold = This indicates a menu or an item that must be selected.
Italic = This indicates sections that you can refer to in this manual.
Multi-language versions
Download other language versions of this E-Manual via this website:
http://support.asus.com
LED projector E-Manual
Safety precautions
Using your LED projector
•
Refer to the manual and take note of the safety instructions
before operating your LED projector.
•
Follow the notes and warnings stated in the user manual.
•
Do not place your LED projector on uneven or unstable surfaces.
•
Do not use your LED projector in smoky environments. Smoke
residue may cause build-up on critical parts and damage the
LED projector or decrease its performance.
•
Do not use damaged power cords, accessories, and other
peripherals with your LED projector.
•
Keep the LED projector’s plastic packages out of the reach of
children.
•
Do not block or place anything near the LED projector’s
ventilation holes. Doing so may cause internal heat build-up
that can degrade picture quality and damage the projector.
•
Ensure that the operating voltage of your LED projector
matches the voltage of your power source.
Servicing and replacement of parts
•
Do not disassemble or attempt to service this LED projector by
yourself. Contact your local ASUS service center for assistance.
•
Risk of explosion if battery is replaced by an incorrect type.
Dispose used batteries according to safety instructions and
contact your local ASUS service center for assistance.
•
When replacing parts of your LED projector, purchase items
as specified by ASUS and contact your local service center for
assistance.
LED projector E-Manual
Caring for your LED projector
•
Switch off then unplug the LED projector from the power outlet
before cleaning it.
•
When cleaning the LED projector’s housing, use a clean soft
cloth dampened with water or a mix of water and neutral
detergent. Wipe it dry using a soft dry cloth.
•
Ensure that the lens is cool before cleaning it. Gently wipe the
lens using a lens cleaning paper. Do not touch the lens with
your hands.
•
Do not use liquid or aerosole cleaners, benzene, or thinners on
your LED projector.
•
Never operate this LED projector immediately after moving it
from a cold location. When the LED projector is exposed to a
drastic change in temperature, moisture may condense on the
lens and its other internal parts. To prevent this, use the unit two
(2) hours after an extreme or sudden change in temperature
occurs.
Proper disposal
Do not throw your LED projector in municipal waste. This
product has been designed to enable proper reuse of parts
and recycling. The symbol of the crossed out wheeled bin
indicates that the product (electrical, electronic equipment
and mercury-containing button cell battery) should not
be placed in municipal waste. Check local regulations for
disposal of electronic products.
Do not throw the battery in municipal waste. The symbol
of the crossed out wheeled bin indicates that the battery
should not be placed in municipal waste.
LED projector E-Manual
Chapter 1:
Knowing your LED
projector
Chapter 1: Knowing your LED
projector
LED projector E-Manual
Features
Top view
Control panel buttons
The control panel buttons allow you to navigate the onscreen
display menu. Individually, these buttons also correspond to a
specific LED projector setting as indicated below.
Splendid/Exit
Left/Volume
down
MENU/OK
Right/
Volume up
NOTE: For more information on using the control panel buttons to
access your LED projector’s settings, refer to Chapter 3: Using your LED
projector
10
LED projector E-Manual
Power indicator and battery status indicator
This LED indicator indicates the following scenarios for your
LED projector:
•
It lights up when the LED projector is powered on.
•
It lights up as either green or red depending on the battery
charge status.
For details on how this LED indicator functions as a battery
status indicator, refer to the following table:
Color
Status
Solid Green
The LED projector is either plugged to a
power source or running on battery mode
and the battery power is more than 25%.
Solid Red
The LED projector is running on battery
mode only and the battery power is not
more than 25%.
Battery charge indicator
This LED indicator lights up when the LED projector is plugged
to a power source using its power adapter.
IMPORTANT! Use only the bundled power adapter to charge
the battery pack and supply power to your LED projector.
LED projector E-Manual
11
Extended features
Your LED projector also have stand-alone features that are launched
by pressing the Splendid/Exit button while your LED projector is on
battery mode.
Flashlight
The LED projector flashes a steady white light when you use this
feature.
Splendid/Exit
button
To use your LED projector as a flashlight:
1. Disconnect all peripherals from your LED projector then press
the power button to turn it on.
2. Open the cover of your LED projector's lens.
3. Press
on the control panel of your LED projector to launch
the NO SIGNAL display.
4. Press
repeatedly until the LED projector flashes a steady
white light.
IMPORTANT! Ensure that your LED projector is charged and can run
on battery mode before enabling this feature. Battery time varies
depending on usage.
12
LED projector E-Manual
Emergency light mode
The LED projector flashes a blinking white light when you use this
feature.
Splendid/Exit
button
To use your LED projector as a flashlight:
1. Disconnect all peripherals from your LED projector then press
the power button to turn it on.
2. Open the cover of your LED projector's lens.
3. Press
on the control panel of your LED projector to launch
the NO SIGNAL display.
4. Press
repeatedly until the LED projector flashes a blinking
white light.
IMPORTANT! Ensure that your LED projector is charged and can run
on battery mode before enabling this feature. Battery time varies
depending on usage.
NOTE: To turn off or switch between the flashlight and emergency
light feature of your LED projector, just press the Splendid/Exit
button until your preferred lighting feature is disabled or enabled.
LED projector E-Manual
13
Front view
Lens
The lens projects video or image files onscreen from your input
device.
WARNING! Do not touch the lens using your hands or any sharp
object.
Lens cover lever
Move this lever to the left to open the lens cover and to the
right to cover the lens when the LED projector is not in use.
Lens cover
The lens cover protects the lens from scratches and possible
dirt build-up.
IMPORTANT! Remove the lens cover before using your LED
projector.
14
LED projector E-Manual
Rear view
Audio output jack port
The audio output jack port allows you to connect your LED
projector to amplified speakers or headphones.
HDMI/MHL port
This port is for the HDMI (High-Definition Multimedia Interface)
connector and also supports MHL (Mobile High-Definition Link)
compatible devices. This port is HDCP compliant for HD DVD,
Blu-ray, and other protected content playback.
Power output port
This power output port provides up to 5V/1A of output voltage
and current. You can connect your mobile device to this port to
keep it charged while using it with your LED projector.
Power (DC) input port
Insert the bundled power adapter into this port to charge the
battery pack and supply power to your LED projector.
WARNING! The adapter may become warm to hot while in
use. Do not cover the adapter and keep it away from your body
while it is connected to a power source.
LED projector E-Manual
15
Power button
Press this power button to turn on or turn off your LED
projector.
Air vents
The air vents allow cool air to enter and warm air to exit the LED
projector.
WARNING! Ensure that paper, books, clothing, cables, or other
objects do not block any of the air vents or else overheating
may occur.
16
LED projector E-Manual
Right side
Focus ring
The focus ring allows you to adjust the image focus of your LED
projector.
Air vents
The air vents allow cool air to enter and warm air to exit the
LED projector.
WARNING! Ensure that paper, books, clothing, cables, or other
objects do not block any of the air vents or else overheating
may occur.
LED projector E-Manual
17
Left side
Air vents
The air vents allow cool air to enter and warm air to exit the
LED projector.
WARNING! Ensure that paper, books, clothing, cables, or other
objects do not block any of the air vents or else overheating
may occur.
18
LED projector E-Manual
Bottom view
Air vents
The air vents allow cool air to enter and warm air to exit the LED
projector.
WARNING! Ensure that paper, books, clothing, cables, or other
objects do not block any of the air vents or else overheating
may occur.
Tripod socket
Attach the LED projector to a tripod using this socket.
LED projector E-Manual
19
20
LED projector E-Manual
Chapter 2:
Setting up
Chapter 2: Setting up
LED projector E-Manual
21
Operating your LED projector
This portable LED projector allows you to plug and play your devices
so you can easily open multimedia files and hear audio straight from
its built-in SonicMaster speakers.
For your safety and to maintain the quality of this unit, refer to the
following steps when operating your LED projector.
1. Connect the LED projector to the power adapter.
A. Connect the power cord to the power adapter.
B. Connect the AC power cord to a power source.
C. Connect the DC power connector to your LED projector.
Charge the LED projector for 3 hours before using it in
battery mode for the first time.
NOTE: The power adapter may vary in appearance, depending on
models and your region.
22
LED projector E-Manual
IMPORTANT!
• Use only the bundled power adapter to charge the battery pack
and supply power to your LED projector.
• Ensure that your LED projector is connected to the power adapter
before turning it on for the first time. We strongly recommend
that you use a grounded wall socket while using your LED
projector on power adapter mode.
• The socket outlet must be easily accessible and near your LED
projector.
• To disconnect your LED projector from its main power supply,
unplug your LED projector from the power socket.
WARNING!
Read the following precautions for your LED projector’s battery.
• The battery used in this device may present a risk of fire or
chemical burn if removed or disassembled.
• Follow the warning labels for your personal safety.
• Risk of explosion if battery is replaced by an incorrect type.
• Do not dispose of in fire.
• Never attempt to short-circuit your LED projector’s battery.
• Never attempt to dissamble and reassemble the battery.
• Discontinue usage if leakage is found.
• The battery and its components must be recycled or disposed of
properly.
• Keep the battery and other small components away from
children.
LED projector E-Manual
23
AC power cord requirements
Use the correct AC plug type according to your current location.
IMPORTANT! Contact your sales dealer if the AC power cord bundled
with your LED projector does not match your local power source.
NOTE: We highly recommend that you use a video source device that
also uses a grounding type plug to prevent signal interference due to
voltage fluctuations.
for Australia and Mainland China
for U.S.A., Canada, and Taiwan
for Continental Europe
for U.K.
for Japan
for Sweden
24
LED projector E-Manual
2. Connect the LED projector to your device.
HDMI/MHL
Audio output
Power output (5V/1A)
LED projector E-Manual
25
3. Press the power button.
NOTE: The battery pack inside your LED projector stops charging
while the LED projector is in use. Refer to the battery indicator for the
current charge status of your LED projector. You may also refer to the
Top View section in this manual for more details.
26
LED projector E-Manual
4. Open the lens cover and adjust the focus ring.
NOTE: Use a still image when adjusting the onscreen display.
A. Open the lens cover by moving its lever to the left.
B. Adjust the image focus of the projection onscreen by moving
the focus ring up or down.
LED projector E-Manual
27
Screen size and projection distance table
Adjust the LED projector’s distance from the screen using the table
below.
Screen size - 16:9
28
(inches)
(millimeters)
Projection distance
(meters)
30
762
0.71
41
1014
0.97
60
1524
1.42
80
2032
1.89
100
2540
2.37
120
3048
2.84
LED projector E-Manual
Chapter 3:
Using the LED projector
Chapter 3:Using the LED
projector
LED projector E-Manual
29
Using your LED projector for the first
time
Refer to the following steps when using your LED projector for the
first time.
1. Set up your LED projector then press the power button.
2. Press
or
on your LED projector's control panel to
browse through the available language options.
3. After you have chosen your prefered language, press
this language for use on your LED projector.
to set
4. You may now start using your LED projector to display files
from your input device. The NO SIGNAL screen may appear if
no input device is connected or cannot be detected by the LED
projector.
5. Press
on your LED projector's control panel to launch its
onscreen display menu.
30
LED projector E-Manual
Operating the onscreen display menu
Your LED projector is a plug-and-play device that also features an
onscreen display menu that contains a set of programs and settings
that can maximize your use of the LED projector.
Launch the onscreen display menu by pressing
panel of your LED projector.
on the control
battery status icon
onscreen display menu options
To navigate the onscreen display menu, press the following buttons
on your LED projector's control panel:
move to the left
LED projector E-Manual
select an item
move to the right
31
Adjusting your LED projector's
settings
Refer to the following steps when accessing the onscreen display
menu options to adjust your LED projector settings:
1. Launch the onscreen display menu.
2. Press
access.
or
3. Press
to open the selected option's settings.
4. Press
or
preference.
to select the menu option you would like to
to adjust the settings according to your
5. When finished, press
to save the new settings and go back
to the home screen.
You may refer to the following pages for details on each of the
onscreen display menu options.
32
LED projector E-Manual
Onscreen display menu options
Volume
Select this menu option to adjust the volume of the audio file played
on your LED projector.
You may adjust the volume on a scale of 0 to 10, from mute to the
loudest possible volume played via your LED projector’s built-in
speakers.
Brightness
Select this menu option to adjust the brightness of your projection
onscreen.
You may adjust the brightness on a scale of 0 to 10, from darkest to
brightest.
LED projector E-Manual
33
Contrast
Select this menu option to adjust the light and dark areas of your
projection onscreen.
You may adjust the contrast on a scale of 0 to 10, from the lowest to
the highest possible color contrast.
Splendid
Select this menu option to activate either of the following display
modes, depending on how the LED projector is powered on. You
may also directly launch this menu option by pressing
.
Refer to the following information for details on the different modes
you can activate via Splendid.
34
LED projector E-Manual
When powered by battery only
NOTE: You may also launch the following modes by directly pressing
the Splendid/Exit button after turning on your LED projector.
•
BATTERY MODE - This mode allows you to optimize power
consumption while running the LED projector on battery power
only.
•
PRESENTATION MODE - This mode allows you to optimize
the brightness of your LED projector and is suitable for quick
presentations of up to ninety (90) minutes.
Connected to a power outlet
•
STANDARD - This mode fits general display uses of the LED
projector.
•
THEATER - This mode is recommended when using the LED
projector to display videos.
LED projector E-Manual
35
Aspect Ratio
Select this menu option to adjust the screen ratio of your projection
onscreen.
You may change the projection of your display according to the
following aspect ratios: AUTO, 4:3, and 16:9.
Projection Position
This option allows you to change the way your projections are
oriented onscreen based from the current location of your LED
projector.
You may change your projection’s orientation to correspond with
the location where your LED projector is currently placed: FRONT
TABLE, REAR CEILING, FRONT CEILING, REAR TABLE.
36
LED projector E-Manual
Setup
Select this menu option to configure the following settings of your
LED projector:
•
LANGUAGE - This option allows you to set the LED projector's
onscreen display menu to other languages.
•
RESET ALL SETTINGS - This option restores all the default
settings of your LED projector.
Information
Select this menu option to see an overview of information about
your LED projector.
model name
LED projector's
firmware version
LED projector E-Manual
input device's
screen resolution
input source
37
Turning off your LED projector
1. Press the power button.
2. When the following screen appears, press the power button
again to completely turn off your LED projector.
NOTE: For safety purposes, charging the battery of your LED projector
may not immediately start after the device is powered off. Once the
projector cools off, charging its battery automatically begins.
38
LED projector E-Manual
Appendices
Appendices
Appendices
LED projector E-Manual
39
Federal Communications Commission
Statement
This equipment has been tested and found to comply with the
limits for a class B digital device, pursuant to Part 15 of the Federal
Communications Commission (FCC) rules. These limits are designed
to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the distance between the equipment and receiver.
•
Connect the equipment to an outlet on a different circuit than
that which the receiver is connected to.
•
Consult the dealer or an experienced radio/TV technician for
help.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference that may cause
undesired operation.
40
LED projector E-Manual
Canadian Department of
Communications Statement
This digital apparatus does not exceed the Class B limits for
radio noise emissions from digital apparatus set out in the
Radio Interference Regulations of the Canadian Department of
Communications.
This class B digital apparatus complies with Canadian ICES-003.
Global Environmental Regulation
Compliance and Declaration
ASUS follows the green design concept to design and manufacture
our products, and makes sure that each stage of the product
life cycle of ASUS product is in line with global environmental
regulations. In addition, ASUS disclose the relevant information
based on regulation requirements.
Please refer to http://csr.asus.com/english/Compliance.htm for
information disclosure based on regulation requirements ASUS is
complied with:
Japan JIS-C-0950 Material Declarations
EU REACH SVHC
Korea RoHS
Swiss Energy Laws
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment
to the highest standards for protecting our environment. We believe
in providing solutions for you to be able to responsibly recycle our
products, batteries, other components as well as the packaging
materials. Please go to http://csr.asus.com/english/Takeback.htm for
detailed recycling information in different regions.
LED projector E-Manual
41
Support PC Timings
HDMI (PC)
Resolution
Mode
Refresh rate (Hz) H-frequency (kHz) Clock (MHz)
800 x 600
SVGA_60
60.317
37.879
40
1024 x 768
XGA_60
60.004
48.363
65
1280 x 720
1280 x 720_60
60
45
74.25
1280 x 800
1280 x 800_60
59.81
49.702
83.5
1280 x 960
1280 x 960_60
60
60
108
1280 x 1024
1280 x 1024_60
60.02
63.98
108
1366 x 768
1366 x 768_60
60
47.712
85.5
1440 x 900
1440 x 900_60
60
55.9
106.5
1680 x 1050
1680 x 1050_60
60
65.3
146.25
1400 x 1050
1400 x 1050_60
60
65.3
121.75
1600 x 1200
1600 x 1200_60
60
75
162
1920 x 1080
1920 x 1080_60
60
67.5
148.5
HDMI (Video)
Timing
Resolution
Vertical frequency H-frequency
(Hz)
(kHz)
Dot Clock Frequency
(MHz)
480i
720 (1440) x 480
59.94
15.73
27
480p
720 x 480
59.94
31.47
27
576i
720 (1440) x 576
50
15.63
27
576p
720 x 576
50
31.25
27
720/50p
1280 x 720
50
37.5
74.25
720/60p
1280 x 720
60
45
74.25
1080/50i
1920 x 1080
50
28.13
74.25
1080/60i
1920 x 1080
60
33.75
74.25
1080/50P
1920 x 1080
50
56.25
148.5
1080/60P
1920 x 1080
60
67.5
148.5
42
LED projector E-Manual
Specifications for S1 LED projector
Display
Display Technology
Light Source
Light Source Life
True Resolution
(native)
Light Output
Contrast Ratio
(typical)
Color Saturation
(NTSC)
Display Colors
Projection Throw Ratio
Lens
Projection Distance
Projection/Screen
Size
Projection Offset
Zoom Ratio
Video
Features
Audio
Features
0.3” DLP®
R/G/B LED
30,000 hrs
WVGA 854 x 480
200 Lumens
1000:1 DCR
100%
16.7 million colors
1.1 (41 in. @ 1 m @ 16:9)
0.73 m to 2.43 m
30 in. to 100 in.
100%
Fixed
Picture Modes
Standard, Theater,
Presentation, Battery,
Flashlight, Emergency light
Aspect Ratio
Auto/ 4:3 / 16:9
Projector Placement Front Table, Front Ceiling, Rear
Table, Rear Ceiling
Built-in speakers
Yes, 2W speaker
Signal
Digital Signal
Frequency Frequency
24.7 KHz(H) to 74.6 KHz(H) /
50 Hz(V) to 60 Hz(V)
(continued on the next page)
LED projector E-Manual
43
Power
Noise
Power On Mode
≤32W
Standby Mode
<0.5W
Acoustic Noise
32dB (Standard mode,
Presentation mode)
28 db (Battery mode,
Theater mode)
Input/
Output
PC Signal Input
HDMI1.3 (HDCP support)/
MHL
Audio Out
Earphone out
USB 2.0 port for
power output
Yes (5V/1A)
Mechanical Chassis Colors
Design
Tripod Socket
Silver
Yes
On-machine Buttons Yes (control panel buttons)
Lens Cover
Yes
Security
Kensington lock
No
Dimension
Physical Dimension
110.5 mm. x 102 mm. x
30.7 mm. (L x W x H)
Weight
Net Weight (Esti.)
342 g.
(continued on the next page)
44
LED projector E-Manual
Operating Temperature 0° C to 40° C
Operating Humidity
20% to 90%
Accessories
power adapter and power cord, carrying
bag, MHL cable (micro USB to HDMI),
HDMI cable, USB to micro USB cable,
warranty card
Regulation Approvals
FCC/UL/CE/CB/CCC/C-tick/VCCI/CU/
TUV-GS
*
Specifications are subject to change without prior notice.
** Product availability may vary by region.
** All brand and product names mentioned are trademarks of their
respective companies.
LED projector E-Manual
45
46
LED projector E-Manual