(Leonite)
Motherboard
P5LP-LE
E2905
Checklist
First Edition V1
October 2006
Contents
P5LP-LE (Leonite) specifications summary ........................................ iii
ii
1.
Motherboard layout ................................................................. 1
2.
Central Processing Unit (CPU) ................................................. 2
3.
System memory ...................................................................... 5
4.
Expansion slots ........................................................................ 8
5.
Jumpers ................................................................................. 11
6.
Connectors ............................................................................ 12
6.1
Rear panel connectors ............................................. 12
6.2
Internal connectors .................................................. 14
P5LP-LE specifications summary
CPU
LGA775 socket for the Intel® Pentium® 4 and
Conroe processor in the 775-land package
Chipset
Northbridge: Intel® 945G Graphics Memory and
Controller Hub (GMCH)
Southbridge: Intel® ICH7DH
Front Side Bus
(FSB)
1066 MHz
Memory
Dual-channel memory architecture
4 x 240-pin DIMM sockets support unbuffered
non-ECC 4 GB 667/533/400 MHZ DDR2 memory
modules
Expansion slots
1 x PCI Express™ x16 slot for discrete graphics card
3 x PCI slots
Rear panel
1 x PS/2 keyboard port
1 x PS/2 mouse port
1 x IEEE 1394a port
1 x LAN (RJ-45) port
6 x audio ports support 8-channel audio configuration
4 x USB 2.0 ports support hot-plug function
1 x VGA port
1 x Coaxial SPDIF out port
1 x Coaxial SPDIF in port
Internal connectors
1 x Floppy connector
1 x IDE connector
1 x 24-pin ATX power connector
1 x 4-pin ATX 12 V power connector
4 x Serial ATA connectors
1 x IEEE 1394a connector
2 x USB 2.0 connectors
1 x CPU fan connector
1 x System fan connector
1 x Internal audio connector
1 x Digital audio connector
1 x Front headphone connector
1 x System panel connector
Storage
Southbridge supports:
- 2 x Ultra DMA 100/66 hard disk drives
- 4 x Serial ATA hard disk drives with hot-swap
function
(continued on the next page)
iii
P5LP-LE specifications summary
Audio
Southbridge supports 8-channel audio configuration
with Intel® High Definition Audio CODEC
Realtek ALC888 High Definition Audio CODEC
LAN
Intel® 82562GT 10/100 Mbps Fast Ethernet
LAN PHY
IEEE 1394
Agere LFW3227 two IEEE 1394a ports
PC health
monitoring
ASUS F8000 for CPU, system, and chassis fan
control, motherboard and CPU temperature
BIOS features
4 Mb SPI Flash ROM
HP BIOS with enhanced ACPI, DMI, Green, and PnP
Features Plus
Form factor
Micro-ATX form factor: 9.6 in x 9.6 in
* Specifications are subject to change without notice
iv
1.
Motherboard layout
24.5cm (9.6in)
CLPWD
PS/2KBMS
T: Mouse
B: Keyboard
F8000
SPDIF
Intel®
945G
GMCH
Top:
Subwoofer Speaker Out
Center
Rear Speaker Out
Below
Side Speaker Out
FLOPPY
ATXPWR
24.5cm (9.6in)
P5LP-LE
Top:Line In
Center:Line Out
Below:Mic In
SYS_FAN3
CPU_FAN
IDE
USB2.0
Top:
T: USB3 RJ-45
B: USB4
DDR2 XMM4 (64 bit,240-pin module)
ATX12V
DDR2 XMM3 (64 bit,240-pin module)
Bottom:
T:USB1 Top:
B:USB2 1394
DDR2 XMM1 (64 bit,240-pin module)
VGA
DDR2 XMM2 (64 bit,240-pin module)
LGA775
PCIEX16
CR2032 3V
Lithium Cell
CMOS Power
PCI1
Intel®
ICH7DH
PCI2
Agere
LFW3227
CLRTC
SATA4
SATA1
SATA3
PC3
ALC888
SPDIF2
SATA2
F_LINE_IN
F_1394
FRONT_USB1
BUZZ1
F_PANEL
F_AUDIO
FRONT_USB2
ASUS P5LP-LE (Leonite)
1
2.
Central Processing Unit (CPU)
The motherboard comes with a surface mount LGA775 socket designed for
the Intel® Pentium® 4 and Conroe processor in the 775-land package.
•
Your boxed Intel® Pentium® 4 processor package should
come with installation instructions for the CPU, heatsink, and the
retention mechanism. If the instructions in this section do not match
the CPU documentation, follow the latter.
•
Upon purchase of the motherboard, make sure that the PnP cap is
on the socket and the socket contacts are not bent. Contact your
retailer immediately if the PnP cap is missing, or if you see any
damage to the PnP cap/socket contacts/motherboard components.
ASUS will shoulder the cost of repair only if the damage is shipment/
transit-related.
•
Keep the cap after installing the motherboard. ASUS will process
Return Merchandise Authorization (RMA) requests only if the
motherboard comes with the cap on the LGA775 socket.
•
The product warranty does not cover damage to the socket
contacts resulting from incorrect CPU installation/removal, or
misplacement/loss/incorrect removal of the PnP cap.
Installing the CPU
To install a CPU:
Locate the CPU socket on the motherboard.
P5LP-LE
1.
P5LP-LE (Leonite) CPU Socket 775
Before installing the CPU, make sure that the socket box is facing
towards you and the load lever is on your left.
2
ASUS P5LP-LE (Leonite)
2.
Press the load lever with your thumb (A), then move it to the left (B)
until it is released from the retention tab.
Retention tab
A
PnP cap
Load lever
B
This side of the
socket box should
face you.
To prevent damage to the socket pins, do not remove the PnP cap
unless you are installing a CPU.
3.
Lift the load lever in the
direction of the arrow to a 135º
angle.
4.
Lift the load plate with your
thumb and forefinger to a
100º angle (A), then push
the PnP cap from the load
plate window to remove (B).
B
A
Load plate
5.
Position the CPU over
the socket, making
sure that the gold
triangle is on the
bottom-left corner of
the socket. The
socket alignment key
should fit into the
CPU notch.
ASUS P5LP-LE (Leonite)
Alignment key
Gold triangle mark
3
6.
Close the load plate (A), then
push the load lever (B) until
it snaps into the retention
tab.
A
B
The CPU fits in only one correct orientation. DO NOT force the CPU into
the socket to prevent bending the connectors on the socket and
damaging the CPU!
Notes on Intel® Hyper-Threading Technology
•
This motherboard supports Intel® Pentium® 4 processor in the
775-land package with Hyper-Threading Technology.
•
Hyper-Threading Technology is supported under Windows® XP/2003
Server and Linux 2.4.x (kernel) and later versions only. Under Linux,
use the Hyper-Threading compiler to compile the code. If you are
using any other operating systems, disable the Hyper-Threading
Techonology item in the BIOS to ensure system stability and
performance.
•
Installing Windows® XP Service Pack 1 or later version is recommended.
•
Make sure to enable the Hyper-Threading Technology item in BIOS
before installing a supported operating system.
•
For more information on Hyper-Threading Technology, visit
www.intel.com/info/hyperthreading.
To use the Hyper-Threading Technology on this motherboard:
4
1.
Install an Intel® Intel® Pentium® 4 processor that supports
Hyper-Threading Technology.
2.
Power up the system and enter the BIOS Setup. Under the Advanced
Menu, make sure that the item Hyper-Threading Technology is set to
Enabled. The item appears only if you installed a CPU that supports
Hyper-Threading Techonology.
3.
Reboot the computer.
ASUS P5LP-LE (Leonite)
3.
System memory
The motherboard comes with four Double Data Rate 2 (DDR2) Dual Inline
Memory Module (DIMM) sockets.
A DDR2 module has the same physical dimensions as a DDR DIMM but has a
240-pin footprint compared to the 184-pin DDR DIMM. DDR2 DIMMs are
notched differently to prevent installation on a DDR DIMM socket.
XMM4
XMM3
XMM2
P5LP-LE
XMM1
The following figure illustrates the location of the DDR2 DIMM sockets.
P5LP-LE (Leonite) 240-pin DDR2 DIMM sockets
3.1
Memory configurations
You can install 256 MB, 512 MB, and 1 GB DDR2 SDRAM DIMMs into the
DIMM sockets using the memory configurations in this section.
•
Installing DDR2 DIMMs other than the recommended configurations
may cause memory sizing error or system boot failure. Use any of
the recommended configurations on the next page.
•
Install only i d e n t i c a l (the same type and size) DDR2 DIMM pairs
using the recommended configurations.
•
Make sure that the memory frequency matches the CPU FSB (Front
Side Bus). Refer to the Memory frequency/CPU FSB synchronization
table on the next page.
•
This motherboard does not support double-sided 16-bit DDR DIMMs.
•
Do not create a three-DIMM configuration in dual-channel mode. The
third DIMM is ignored in the dual-channel operation.
ASUS P5LP-LE (Leonite)
5
Recommended memory configurations
Sockets
Mode
Single-channel
(1)
DIMM2
DIMM3
DIMM4
Installed
—
—
—
(2)
—
Installed
—
—
(3)
—
—
Installed
—
—
Installed
(4)
Dual-channel*
DIMM1
—
—
(1)
Installed
—
Installed
—
(2)
—
Installed
—
Installed
(3)
Installed
Installed
Installed
Installed
* Use only identical DDR2 DIMM pairs.
Memory frequency/CPU FSB synchronization
6
CPU FSB
DDR DIMM Type
1066 MHz
PC2-5300/PC2-4200
Memory Frequency
667/533 MHz
800 MHz
PC2-5300/PC2-4200/PC2-3200
667/533/400 MHz
533 MHz
PC2-5300/PC2-4200/PC2-3200
667/533/400 MHz
ASUS P5LP-LE (Leonite)
3.2
Installing a DDR2 DIMM
Unplug the power supply before adding or removing DIMMs or other
system components. Failure to do so can cause severe damage to both
the motherboard and the components.
2
To install a DIMM:
1.
Unlock a DIMM socket by
pressing the retaining clips
outward.
2.
Align a DIMM on the socket
such that the notch on the
DIMM matches the break on
the socket.
3.
3
DDR2 DIMM notch
1
Firmly insert the DIMM into the
socket until the retaining clips
snap back in place and the
DIMM is properly seated.
Unlocked retaining clip
3.3
•
A DDR2 DIMM is keyed with a notch so that it fits in only one
direction. Do not force a DIMM into a socket to avoid damaging the
DIMM.
•
The DDR2 DIMM sockets do not support DDR DIMMs. Do not install
DDR DIMMs to the DDR2 DIMM sockets.
Removing a DDR2 DIMM
To remove a DIMM:
1.
Support the DIMM lightly
with your fingers when
pressing the retaining
clips. The DIMM might get
damaged when it flips out
with extra force.
2.
2
Simultaneously press the retaining
clips outward to unlock the DIMM.
1
1
DDR2 DIMM notch
Remove the DIMM from the socket.
ASUS P5LP-LE (Leonite)
7
4.
Expansion slots
In the future, you may need to install expansion cards. The following
sub-sections describe the slots and the expansion cards that they support.
Make sure to unplug the power cord before adding or removing
expansion cards. Failure to do so may cause you physical injury and
damage motherboard components.
4.1
Installing an expansion card
To install an expansion card:
1.
Before installing the expansion card, read the documentation that
came with it and make the necessary hardware settings for the card.
2.
Remove the system unit cover (if your motherboard is already
installed in a chassis).
3.
Remove the bracket opposite the slot that you intend to use. Keep
the screw for later use.
4.
Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
5.
Secure the card to the chassis with the screw you removed earlier.
6.
Replace the system cover.
4.2
Configuring an expansion card
After installing the expansion card, configure it by adjusting the software
settings.
1.
Turn on the system and change the necessary BIOS settings, if any.
2.
Assign an IRQ to the card. Refer to the tables on the next page.
3.
Install the software drivers for the expansion card.
When using PCI cards on shared slots, ensure that the drivers support
“Share IRQ” or that the cards do not need IRQ assignments; otherwise,
conflicts will arise between the two PCI groups, making the system
unstable and the card inoperable. Refer to the table on the next page for
details.
8
ASUS P5LP-LE (Leonite)
Standard interrupt assignments
IRQ
Standard Function
0
System Timer
1
Standard 101/102-key or Microsoft® Natural PS/2 Keyboard
2
Programmable Interrupt Controller
3
Intel® USB Enhanced Host Controller
3
Intel® USB Universal Host Controller
4
Intel® USB Universal Host Controller
6
Standard Floppy Disk Controller
7
ECP Printer Port
8
System CMOS/Real Time Clock
9
SCI IRQ used by ACPI Bus
10
Intel® PCI Express Root Port
10
Intel® VGA Controller
10
Intel® ICH7DH High Definition Audio Controller
10
Intel® USB Universal Host Controller
11
VIA OHCI Compliant IEEE 1394 Host Controller
11
Intel® ICH7DH Integrated LAN Controller
12
Microsoft® Port Mouse
13
Numeric Data Processor
14
Intel® USB Universal Host Controller
14
Intel® Ultra ATA Storage Controllers
14
Intel® SMBus Controller
IRQ assignments for this motherboard
A
B
C
D
E
F
PCI slot 1
—
—
—
shared
—
—
PCI slot 2
shared
—
—
—
—
—
PCI slot 3
—
used
—
—
—
—
Onboard LAN
—
—
—
—
—
used
Onboard 1394 controller
—
—
—
—
used
—
ASUS P5LP-LE (Leonite)
9
PCI Express slot
This motherboard has one PCI
Express slot, which supports a
164-pin x16 interface graphics
card.
PCI slots
There are three 32-bit PCI slots on
this motherboard. The slots
support PCI cards such as a LAN
card, SCSI card, USB card, and
other cards that comply with PCI
specifications.
10
ASUS P5LP-LE (Leonite)
5.
Jumpers
Clear RTC RAM (3-pin CLRTC)
This jumper allows you to clear the Real Time Clock (RTC) RAM in
CMOS. You can clear the CMOS memory of date, time, and system
setup parameters by erasing the CMOS RTC RAM data. The onboard
button cell battery powers the RAM data in CMOS, which include
system setup information such as system passwords.
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Move the jumper cap from pins 2-3 (Normal) to pins 1-2 (Clear
CMOS). Keep the cap on pins 1-2 for about 5~10 seconds, then
move the cap back to pins 2-3.
3. Plug the power cord and turn ON the computer.
4. Hold down the <Del> key during the boot process and enter BIOS
setup to re-enter data.
P5LP-LE
Except when clearing the RTC RAM, never remove the cap from the
default position. Removing the cap will cause system boot failure!
P5LP-LE (Leonite)
Clear RTC RAM
CLRTC
2
1
Clear CMOS
3
2
Normal
(Default)
Clear password (3-pin CLPWD)
This jumper allows you to clear the password if you forgot your
password.
CLPWD
P5LP-LE
2
1
Clear Password
3
2
Normal
(Default)
P5LP-LE (Leonite)
Clear password setting
ASUS P5LP-LE (Leonite)
11
6.
Connectors
6.1
Rear panel connectors
1
2
3
4
5
6
7
8
9
15
13
12
11
10
1.
2.
P S / 2 m o u s e p o r t ( g r e e n ) . This port is for a PS/2 mouse.
I E E E 1 3 9 4 a p o r t . This 6-pin IEEE 1394a port provides high-speed
connectivity for audio/video devices, storage peripherals, PCs, or
portable devices.
3.
L A N ( R J - 4 5 ) p o r t . This port allows connection to a Local Area
Network (LAN) through a network hub.
4.
S i d e S p e a k e r O u t p o r t ( g r a y ) . This port connects to the side
speakers in an 8-channel audio configuration.
R e a r S p e a k e r O u t p o r t ( b l a c k ) . This port connects to the rear
speakers on a 4-channel, 6-channel, or 8-channel audio configuration.
5.
6.
C e n t e r / S u b w o o f e r p o r t ( y e l l o w o r a n g e ) . This port connects
the center/subwoofer speakers.
7.
L i n e I n p o r t ( l i g h t b l u e ) . This port connects a tape, CD, DVD
player or other audio sources.
8.
L i n e O u t p o r t ( l i m e ) . This port connects a headphone or a
speaker. In 4-channel, 6-channel, and 8-channel mode, the function of
this port becomes Front Speaker Out.
M i c r o p h o n e p o r t ( p i n k ) . This port connects a microphone.
9.
12
14
ASUS P5LP-LE (Leonite)
Audio 2, 4, 6, or 8-channel configuration
Port
Headset/
2-channel
4-channel
6-channel
Light Blue
Line In
Line In
Line In
Line In
Lime
Line Out
Front Speaker Out
Front Speaker Out
Front Speaker Out
Pink
Mic In
Mic In
Mic In
Mic In
-
-
Center/Subwoofer
Center/Subwoofer
Black
-
Rear Speaker Out
Rear Speaker Out
Rear Speaker Out
Gray
-
-
-
Side Speaker Out
Yellow Orange
8-channel
1 0 . U S B 2 . 0 p o r t s 3 a n d 4 . These two 4-pin Universal Serial Bus
(USB) ports are available for connecting USB 2.0 devices.
1 1 . U S B 2 . 0 p o r t s 1 a n d 2 . These two 4-pin Universal Serial Bus
(USB) ports are available for connecting USB 2.0 devices.
1 2 . V i d e o G r a p h i c s A d a p t e r p o r t . This 15-pin port is for a VGA
monitor or other VGA-compatible devices.
1 3 . C o a x i a l S / P D I F O u t p o r t . This port connects an external audio
output device via a coaxial S/PDIF cable.
1 4 . C o a x i a l S / P D I F I n p o r t . This port connects an external audio input
device via a coaxial S/PDIF cable.
1 5 . P S / 2 k e y b o a r d p o r t ( p u r p l e ) . This port is for a PS/2 keyboard.
ASUS P5LP-LE (Leonite)
13
6.2
Internal connectors
This section describes and illustrates the internal connectors on the
motherboard.
1.
Floppy disk drive connector (34-1 pin FLOPPY)
This connector is for the provided floppy disk drive (FDD) signal cable.
Insert one end of the cable to this connector, then connect the other
end to the signal connector at the back of the floppy disk drive.
Pin 5 on the connector is removed to prevent incorrect cable connection
when using an FDD cable with a covered Pin 5.
PIN 1
FLOPPY
P5LP-LE
NOTE: Orient the red markings on
the floppy ribbon cable to PIN 1.
P5LP-LE (Leonite) Floppy disk drive connector
14
ASUS P5LP-LE (Leonite)
2.
IDE connector (40-1 pin IDE)
This connector is for an Ultra DMA 100/66 signal cable. The Ultra DMA
100/66 signal cable has three connectors: a blue connector for the
primary IDE connector on the motherboard, a black connector for an
Ultra DMA 100/66 IDE slave device (optical drive/hard disk drive), and
a gray connector for an Ultra DMA 100/66 IDE master device (hard disk
drive). If you install two hard disk drives, you must configure the
second drive as a slave device by setting its jumper accordingly. Refer
to the hard disk documentation for the jumper settings.
•
Pin 20 on the IDE connector is removed to match the covered hole
on the Ultra DMA cable connector. This prevents incorrect insertion
when you connect the IDE cable.
•
Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices.
IDE
P5LP-LE
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
P5LP-LE (Leonite) IDE connector
ASUS P5LP-LE (Leonite)
PIN 1
15
3.
ATX power connectors (24-pin ATXPWR, 4-pin ATX12V)
These connectors are for an ATX power supply. The plugs from the
power supply are designed to fit these connectors in only one
orientation. Find the proper orientation and push down firmly until the
connectors completely fit.
•
Do not forget to connect the 4-pin ATX +12 V power plug;
otherwise, the system will not boot up.
•
Make sure that your ATX 12V power supply can provide 8A on the
+12V lead and at least 1A on the +5-volt standby lead (+5VSB).
The minimum recommended wattage is 230W, or 300W for a fully
configured system. The system can become unstable and might
experience difficulty powering up if the power supply is inadequate.
•
You must install a PSU with a higher power rating if you intend to
install additional devices.
ATXPWR
ATX12V
P5LP-LE
GND +12V DC
GND +12V DC
P5LP-LE (Leonite) ATX power connectors
16
+3 Volts
-12 Volts
Ground
PSON#
Ground
Ground
Ground
-5 Volts
+5 Volts
+5 Volts
+5 Volts
Ground
+3 Volts
+3 Volts
Ground
+5 Volts
Ground
+5 Volts
Ground
Power OK
+5V Standby
+12 Volts
+12 Volts
+3 Volts
ASUS P5LP-LE (Leonite)
4.
Serial ATA connectors
(7-pin SATA1 [black], SATA2 [white], SATA3 [blue],
SATA4 [yellow])
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
GND
RSATA_TXP4
RSATA_TXN4
GND
RSATA_RXP4
RSATA_RXN4
GND
SATA1
SATA3
GND
RSATA_TXP3
RSATA_TXN3
GND
RSATA_RXP3
RSATA_RXN3
GND
P5LP-LE (Leonite) SATA connectors
SATA4
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND
P5LP-LE
SATA2
Important notes on Serial ATA
•
Install the Windows® 2000 Service Pack 4 or the Windows® XP
Service Pack1 before using Serial ATA.
•
When using the connectors in S t a n d a r d I D E mode, connect the
primary (boot) hard disk drive to the SATA1 connector. Refer to the
table below for the recommended SATA hard disk drive connections.
Serial ATA hard disk drive connection
Connector
Color
Setting
Use
SATA1
Black
Master
Boot Disk
SATA2
White
Master
Boot Disk
SATA3
Blue
Slave
Data Disk
SATA4
Yellow
Slave
Data Disk
ASUS P5LP-LE (Leonite)
17
IEEE 1394a connector (10-1 pin F_1394)
This connector is for an IEEE 1394a port. Connect the IEEE 1394a
module cable to this connector, then install the module to a slot
opening at the back of the system chassis.
P5LP-LE
5.
GND
+12V
TPBGND
TPA-
F_1394
+12V
TPB+
GND
TPA+
1
P5LP-LE (Leonite) IEEE 1394 connector
NEVER connect a U S B c a b l e to the IEEE 1394a connector. Doing so
will damage the motherboard!
6.
USB connectors (10-1 pin FRONT_USB1, FRONT_USB2)
These connectors are for USB 2.0 ports. Connect the USB/GAME
module cable to any of these connectors, then install the module to a
slot opening at the back of the system chassis. These USB connectors
comply with USB 2.0 specification that supports up to 480 Mbps
connection speed.
GND
USB_P5+
USB_P5USB+5V
NC
GND
USB_P6+
USB_P6USB+5V
P5LP-LE
GND
USB_P5+
USB_P5USB+5V
FRONT_USB2
NC
GND
USB_P6+
USB_P6USB+5V
FRONT_USB1
P5LP-LE (Leonite) USB 2.0 connectors
Never connect a 1 3 9 4 c a b l e to the USB connectors. Doing so will
damage the motherboard!
18
ASUS P5LP-LE (Leonite)
7.
CPU and System fan connectors
(4-pin CPU_FAN, 3-pin SYS_FAN3)
The fan connectors support cooling fans of 350 mA ~ 740 mA
(8.88 W max.) or a total of 1 A~2.22 A (26.64 W max.) at +12 V.
Connect the fan cables to the fan connectors on the motherboard,
making sure that the black wire of each cable matches the ground pin
of the connector.
SYS_FAN3
GND
+12V
Rotation
CPU_FAN
PWN
Rotation
+12V
GND
P5LP-LE
Do not forget to connect the fan cables to the fan connectors.
Insufficient air flow inside the system may damage the motherboard
components. These are not jumpers! DO NOT place jumper caps on the
fan connectors.
P5LP-LE (Leonite) Fan connectors
8.
Internal audio connector (F_LINE_IN)
P5LP-LE
This connector allows you to receive stereo audio input from sound
sources such as a CD-ROM, TV tuner, or MPEG card.
F_LINE_IN
AUX_LCR
SENSE
GND
AUX_RCR
P5LP-LE (Leonite) Internal audio connector
ASUS P5LP-LE (Leonite)
19
9.
Digital audio connector (3-pin SPDIF2 )
This connector is for an additional Sony/Philips Digital Interface
(S/PDIF) port(s). Connect the S/PDIF module cable to this connector,
then install the module to a slot opening at the back of the system
chassis.
P5LP-LE
The S/PDIF module is purchased separately.
SPDIF2
(White)
+5V
SPDIF_OUT
GND
P5LP-LE (Leonite) Digital audio connector
10. Front panel audio connector (10-1-pin F_AUDIO)
This connector is for a chassis-mounted front panel headphone port.
P5LP-LE
MIC2_L
MIC2_R
LIN2_R
SENSE
LIN2-L
1
F_AUDIO
GND
AUDIO_PRES#
MIC2_RTU
LIN2_RTU
P5LP-LE (Leonite) Front panel audio connector
20
ASUS P5LP-LE (Leonite)
1 1 . System panel connector (10-1 pin F_PANEL)
This connector supports several chassis-mounted functions.
P5LP-LE
NC
Reset
Ground
HDLEDHDLED+
Reset HDD LED
GND
PWR
PLEDPLED+
F_PANEL
Power Button
Power LED
P5LP-LE (Leonite) System panel connector
•
System power LED
This 2-pin connector is for the system power LED. Connect the
chassis power LED cable to this connector. The system power LED
lights up when you turn on the system power, and blinks when the
system is in sleep mode.
•
Hard disk drive activity
This 2-pin connector is for the HDD Activity LED. Connect the HDD
Activity LED cable to this connector. The IDE LED lights up or flashes
when data is read from or written to the HDD.
•
Power/Soft-off button
This connector is for the system power button. Pressing the power
button turns the system ON or puts the system in SLEEP or SOFT-OFF
mode depending on the BIOS settings. Pressing the power switch for
more than four seconds while the system is ON turns the system OFF.
•
Reset button
This 2-pin connector is for the chassis-mounted reset button for
system reboot without turning off the system power.
ASUS P5LP-LE (Leonite)
21
22
ASUS P5LP-LE (Leonite)