Technical data | ATD Tools 10515 Saw User Manual

ATD-10515
14" Cut-off Saw with Laser Guide
Operation and Safety Instructions
07/12
Table of contents
SECTION
I.
II.
III.
IV.
V.
VI.
VII.
VIII.
IX.
PAGE
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
General safety rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Specific safety rules for the cut-off saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Electrical information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Know your cut-off saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Assembly and adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Replacement parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
I. Technical data
14" CUT-OFF SAW WITH LASER LINE
MOTOR:
HORSEPOWER:
MOTOR SPEED:
CUTTING DISC:
ARBOR:
SWIVELLING VISE CLAMP:
120 V, 60 Hz, 15 A
2 1/2
3800 RPM (no load)
14" (35.5 cm)
1" (2.5 cm)
0–45˚ right, 0–45˚ left
MAXIMUM CUTTING DIAMETER:
4" (10 cm)
LASER MODULE:
Class III, battery-operated
LASER WAVELENGTH:
LASER OUTPOWER:
NET WEIGHT:
640–660 nm
≤5 mW
43 lb(19.5kg)
2
II. General safety rules
Safety is a combination of common sense, staying alert, and knowing how your cut-off saw
works.
WARNING: TO AVOID MISTAKES THAT COULD CAUSE SERIOUS INJURY, DO NOT
PLUG IN THE CUT-OFF SAW UNTIL THE FOLLOWING STEPS HAVE BEEN READ AND
UNDERSTOOD.
1. READ and become familiar with this entire instruction manual. Learn the tool’s
applications, limitations, and possible hazards.
2. AVOID DANGEROUS CONDITIONS. DO NOT use power tools in wet or damp areas or
expose them to rain. Keep work area well-lit.
3. DO NOT use power tools in the presence of flammable liquids or gases.
4. ALWAYS keep your work area clean, uncluttered, and well-lit. DO NOT work on floor
surfaces that are slippery from sawdust or wax.
5. KEEP BYSTANDERS AT A SAFE DISTANCE FROM the work area, especially when tool
is operating. NEVER allow children or pets near the tool.
6. DO NOT FORCE THE TOOL to do a job for which it was not designed to perform.
7. DRESS FOR SAFETY. DO NOT wear loose clothing, gloves, neckties, or jewellery
(rings, watches, etc.) when operating tool. Inappropriate clothing and items can get
caught in moving parts and draw you in. ALWAYS wear non-slip footwear and tie back
long hair.
8. WEAR A FACE MASK OR DUST MASK as the sawing operation produces dust.
9. ALWAYS remove the power cord plug from the electrical outlet when making
adjustments, changing parts, cleaning or working on the tool.
10. KEEP GUARDS IN PLACE AND IN WORKING ORDER.
11. AVOID ACCIDENTAL START-UPS. Make sure that the power switch is in the OFF
position before plugging in the power cord.
12. REMOVE ADJUSTMENT TOOLS. ALWAYS MAKE SURE all adjustment tools are
removed from the cut-off saw before turning it on.
13. NEVER LEAVE A RUNNING TOOL UNATTENDED. Turn the power switch to OFF.
DO NOT leave tool until it has come to a complete stop.
14. NEVER STAND ON THE TOOL. Serious injury could result if the tool tips or is
accidentally hit. DO NOT store anything above or near the tool.
15. DO NOT OVERREACH. Keep proper footing and balance at all times. Wear oil-resistant,
rubber-soled footwear. Ensure the floor is not subjected to accumulation of oil, scrap, and
other debris.
16. MAINTAIN TOOLS PROPERLY. ALWAYS keep tools clean and in good working order.
Follow instructions for lubricating and changing accessories.
SAVE THESE SAFETY INSTRUCTIONS
3
II. General safety rules ... continued
17. CHECK FOR DAMAGED PARTS. Check moving parts for alignment, jamming, breakage,
improper mounting, or any other conditions that may affect the tool's operation. Any part
that is damaged should be properly repaired or replaced before use.
18. MAKE WORKSHOP CHILDPROOF. Use padlocks, master switches, and always remove
starter keys.
19. DO NOT operate tool if you are under the influence of drugs, alcohol or medication that
could affect your ability to use the tool properly.
20. WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS. Double insulation
does not take the place of normal safety precautions when operating this tool.
WARNING: DUST GENERATED FROM CERTAIN MATERIALS CAN BE HAZARDOUS TO
YOUR HEALTH. ALWAYS OPERATE THE CUT-OFF SAW IN A WELL-VENTILATED AREA.
USE DUST COLLECTION SYSTEMS WHENEVER POSSIBLE. USE A FACE MASK OR
DUST MASK WHEN OPERATING THE CUT-OFF SAW.
ALWAYS WEAR EYE PROTECTION.
A cut-off saw can throw foreign objects into your eyes which
could cause permanent eye damage.
ALWAYS wear safety goggles (not glasses). Ordinary eyeglasses
have only impact-resistant lenses...they ARE NOT safety
goggles.
LASER SAFETY
The laser light beam used in this system is Class III with a maximum ≤5 mW and
640–660 nm wavelength.
WARNING: DO NOT STARE DIRECTLY AT THE LASER BEAM! A HAZARD MAY EXIST
IF YOU DELIBERATELY STARE INTO THE BEAM.
PLEASE OBSERVE ALLSAFETY RULES AS FOLLOWS:
• THE LASER SHALL BE USED AND MAINTAINED IN ACCORDANCE WITH THE
MANUFACTURER'S INSTRUCTIONS.
• NEVER AIM THE BEAM AT ANY PERSON OR AN OBJECT OTHER THAN THE
WORKPIECE.
• DO NOT PROJECT THE LASER BEAM INTO THE EYES OF OTHERS.
• ALWAYS ENSURE THE LASER BEAM IS AIMED AT A WORKPIECE WITHOUT
REFLECTIVE SURFACES AS THE LASER BEAM COULD BE PROJECTED INTO
YOUR EYES OR THE EYES OF OTHERS.
SAVE THESE SAFETY INSTRUCTIONS
4
III. Specific safety rules for the cut-off saw
WARNING: DO NOT OPERATE YOUR CUT-OFF SAW UNTIL IT IS COMPLETELY
ASSEMBLED AND INSTALLED ACCORDING TO THE INSTRUCTIONS.
1. If you are not thoroughly familiar with the operation of a cut-off saw, obtain advice from a
supervisor, instructor, or other qualified person.
2. ALWAYS WEAR SAFETY GOGGLES. Wear hearing protection during periods of
extended operation.
3. REPLACE CRACKED METAL CUTTING DISC IMMEDIATELY. Handle disc carefully and
inspect for cracks before each use. Tighten spindle bolt enough to hold the disc firmly.
Use only the disc flanges provided with your cut-off saw.
4. DO NOT stand in front of the cut-off saw when starting it. To start the saw, stand to one
side and turn ON. Wait until the cut-off saw comes to full speed. There is always the
possibility that a piece from a damaged disc may be thrown off when coming to full
speed.
5. ONLY USE abrasive cut-off discs rated at 4100 RPM or higher.
6. NEVER USE A CIRCULAR SAW BLADE or tooth-type blade in the cut-off saw.
7. DO NOT CUT wood with this cut-off saw.
8. DO NOT USE THE CUT-OFF SAW with the upper or lower blade guard removed.
9. ALWAYS CLAMP THE WORKPIECE with the vise clamp assembly when cutting.
10. CAUTION! Flying sparks will occur when cutting. Sparks can cause personal injury and
ignite flammable materials.
11. DO NOT TOUCH the workpiece after cutting. It is hot and could burn the skin.
12. RELEASE TRIGGER SWITCH AND ALLOW THE CUTTING DISC TO COME TO A
COMPLETE STOP BEFORE REMOVING ANYTHING FROM THE CUT-OFF SAW
TABLE.
13. KEEP HANDS AWAY from rotating parts.
14. AVOID DANGEROUS CONDITIONS. Do not use the cut-off saw in wet or damp areas, or
expose to rain. Use the cut-off saw in a well-ventilated area. FOR INDOOR USE ONLY.
SAVE THESE SAFETY INSTRUCTIONS
5
IV. Electrical information
GROUNDING INSTRUCTIONS
IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides the path of
least resistance for electric current to reduce the risk of electric shock. This tool is equipped
with an electric cord that has an equipment grounding conductor and a grounding plug. The
plug MUST be plugged into a matching outlet that is properly installed and grounded in
accordance with ALL local codes and ordinances.
DO NOT MODIFY THE PLUG PROVIDED. If it will not fit in the outlet, have the proper outlet
installed by a qualified electrician.
IMPROPER CONNECTION of the equipment grounding
conductor can result in risk of electric shock. The conductor
with the green insulation (with or without yellow stripes) is the
equipment grounding conductor. If repair or replacement of the
electric cord or plug is necessary, DO NOT connect the
equipment grounding conductor to a live terminal.
CHECK with a licensed electrician or service person if you do
not completely understand the grounding instructions, or if you
are not sure if the tool is properly grounded.
Fig. A
1
3
2
1 - 3-prong plug 2 - Properly grounded outlet
3 - Grounding prong
USE 3-WIRE EXTENSION CORDS that have 3-prong plugs and 3-prong outlets that accept
the tool's plug as shown in Fig. A. Repair or replace damaged or worn cord immediately.
CAUTION: IN ALL CASES, MAKE CERTAIN THE OUTLET IN QUESTION IS PROPERLY
GROUNDED. IF YOU ARE NOT SURE IF IT IS, HAVE A CERTIFIED ELECTRICIAN CHECK
THE OUTLET.
WARNING: THIS CUT-OFF SAW IS FOR INDOOR USE ONLY. DO NOT EXPOSE TO
RAIN OR USE IN DAMP LOCATIONS.
SAVE THESE SAFETY INSTRUCTIONS
6
IV. Electrical information ... continued
GUIDELINES FOR USING EXTENSION CORDS
Make sure your extension cord is in good condition. When using an extension cord, be sure
to use one heavy enough to carry the current your product will draw. An undersized cord will
cause a drop in line voltage resulting in loss of power and overheating. The table below
shows the correct size to use according to cord length and nameplate ampere rating. If in
doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
Minimum Gauge for Extension Cords (AWG)
(when using 120 V only)
Ampere Rating
Total Length of Cord in Feet (metres)
More Than
Not More Than
25' (7.6 m)
50' (15 m)
100' (30.4 m)
150' (45.7 m)
0
6
18
16
16
14
6
10
18
16
14
12
10
12
16
16
14
12
12
16
14
12
Not Recommended
Make sure your extension cord is properly wired and in good condition. Always replace a
damaged extension cord or have it repaired by a qualified person before using it. Protect your
extension cords from sharp objects, excessive heat and damp or wet areas.
Use a separate electrical circuit for your tools. This circuit should not be less than a #12 wire
and should be protected with a 15 A time-delayed fuse. Before connecting the motor to the
power line, make sure the switch is in the OFF position and the electric current is rated the
same as the current stamped on the motor nameplate. Running at a lower voltage will
damage the motor.
WARNING: THIS CUT-OFF SAW MUST BE GROUNDED WHILE IN USE TO PROTECT
THE OPERATOR FROM ELECTRICAL SHOCK.
SAVE THESE SAFETY INSTRUCTIONS
7
V. Know your cut-off saw
Q
e
B
R
A
C
D
O
E
P
F
O
S
G
H
I
J
K
N
L
M
A
B
C
D
E
F
G
H
I
J
D-handle
Trigger switch
Reset switch
Upper blade guard
Arbor lock
Lower blade guard
14" metal cutting disc
Angle plate
Vise pressure plate
Quick-release latch
K
L
M
N
O
P
Q
R
S
8
Vise handle
Vise wheel
Saw table
Depth stop bolt
Wheel lock lever
Carbon brush cap
Carrying handle
Laser switch
Wrench
VI. Assembly and adjustments
Unpacking (Fig. 1)
Fig. 1
1. Remove the cut-off saw (1) from the carton
by lifting it by the carrying handle.
2. Place the cut-off saw on a secure surface
and examine it carefully. Ensure that you
have:
• 14" cut-off saw assembly (1)
• Vise clamp handle (2)
• Threaded bolt and nut (3)
• Blade wrench (4)
1
2
4
3
WARNING: IF ANY PART IS MISSING OR DAMAGED, DO NOT PLUG IN THE CUTOFF SAW UNTIL THE MISSING OR DAMAGED PART IS REPLACED.
Although this cut-off saw requires minimal
assembly, it does, however, require adjustments
to operate properly. For your safety, make all
adjustments prior to plugging in the cut-off saw.
Fig. 2
4
3
2
Vise clamp assembly (Fig. 2)
1. Insert the bolt (1) through the vise clamp
handle (2).
1
2. Tighten the nut (3) on the bolt.
3. Insert the assembled handle into the
opening (4) on the vise wheel and turn
handle clockwise to secure to the wheel.
Fig. 3
Raise/lower the saw (Fig. 3)
1. Pull out the wheel lock lever (1) and use the
handle to raise or lower the cut-off saw.
2. Push in the wheel lock lever (1) to lock the
cut-off saw in the raised or lowered position.
9
1
VII. Operation
ON/OFF trigger switch (Fig. 4)
Fig. 4
To start the cut-off saw, squeeze the trigger
switch (1). To stop the cut-off saw, release the
trigger switch.
1
Reset switch (Fig. 4)
If the cut-off saw does not start when the trigger
switch is depressed, press the reset switch (2).
Squeeze the trigger switch to start.
2
Swivelling vise clamp assembly with
quick-release latch (Fig. 5)
1
Always secure the workpiece between the angle
plate and the vise pressure plate when cutting.
Fig. 5
2
5
3
1. Place the workpiece between the angle
plate (1) and the vise pressure plate (2).
2. Push the vise screw (3) toward the angle
plate and turn the vise wheel (4) clockwise to
secure. To release, turn the wheel counterclockwise two turns, raise the quick-release
latch (5) and pull the vise screw towards you.
Fig. 6
1
Angle plate (Fig. 6 and 7)
The angle plate can be moved forward,
backward, or rotated for angle cutting.
2
1. To set a cutting angle, loosen the two bolts (1)
and rotate the angle plate (3) up to 45˚ right
or 45˚ left. Align the index (2) with the red line
on the saw table. Retighten the bolts.
2. Always centre the workpiece over the table
slot-web to maximize cutting depths. Move the
vise pressure plate (4) toward the angle
plate (3). Tighten angle plate bolts (2) and
vise pressure plate (4).
3. To move the angle plate (3), remove the two
bolts (1) and washers. Move the angle plate to
the desired position and align the angle plate
with the threaded holes on the saw base.
Insert the two bolts and washers and tighten
to secure the angle plate to the table.
10
3
Fig. 7
4
3
4
VII. Operation ... continued
Installation and removal of metal cutting disc
(Fig. 8 and 9)
1. Unplug the cut-off saw.
2. Push the arbor lock lever (1) towards the metal
cutting disc (2) and slowly turn the disc (either
direction) until the disc locks. (Fig. 8)
3. Push back the lower blade guard (3) and loosen
the hex bolt (6) in the centre of the disc using
the wrench. Remove the bolt (6), washer (5),
flange (4), and disc (2). (Fig. 9).
4. To install a new metal cutting disc, reverse the
process in step 3. Do not overtighten the bolt.
5. Make sure all guards are in place and the disc
rotates freely.
6. Adjust the depth stop bolt (Fig. 10). Return the
wrench to the storage slot.
7. Plug in the cut-off saw.
8. Run the cut-off saw and check to make sure the
disc is in good condition. Always stand to one
side when turning on the cut-off saw. When
testing a new disc, run the the cut-off saw for
3 minutes. When testing an existing disc, run the
cut-off saw for 1 minute.
Adjusting the cutting depth (Fig. 10)
The diameter of the metal cutting disc decreases
with use. The depth stop bolt should be adjusted
periodically to prevent the disc from cutting the
work surface below the cut-off saw table.
1. Loosen the lock nut (1).
2. Turn the stop bolt (2) to set the downward travel
of the disc.
3. Lower the saw to check the depth.
4. Repeat steps 2 and 3 until the downward travel
of the disc is at the desired level.
5. Tighten the lock nut (1) to secure the cutting
depth assembly.
11
Fig. 8
1
3
2
Fig. 9
2
4
5
Fig. 10
1
2
6
VII. Operation ... continued
Cutting workpiece (Fig. 11)
Fig. 11
1. Set the angle plate (1) to the desired cutting
angle.
2. Make sure the workpiece lies flat on the cutoff saw table.
3. Use the vise (2) to secure the workpiece to
1
the table.
2
4. Squeeze the trigger switch.
5. After the motor reaches full speed, lower the
disc into the centre of the workpiece.
6. Using a smooth, firm, and gentle downward
motion, make a clean cut through the
workpiece. Do not allow the disc to bump or jump when making contact with the
workpiece; this may damage both the workpiece and the disc.
7. Keep consistent pressure when coming to the bottom of the cut to avoid forming a heavy
burr and overheating the workpiece.
8. Raise the disc completely from the workpiece before releasing the trigger switch and allow
the motor to stop before removing the workpiece.
Note: A long workpiece should be supported on both ends with blocks of a non-flammable
material so that the workpiece is level with the cut-off saw table.
WARNING: DO NOT STARE DIRECTLY AT THE LASER BEAM! A HAZARD MAY EXIST
IF YOU DELIBERATELY STARE INTO THE BEAM, PLEASE OBSERVE ALL SAFETY
RULES.
Using the laser line (Fig. 12)
1. Secure the workpiece in the vise clamp.
2. Turn the laser switch (1) to the ON position.
3. Check the location of the laser line on the
workpiece. Move the workpiece (2), if
needed.
12
Fig. 12
1
2
VIII. Maintenance
WARNING: TO AVOID INJURY FROM UNEXPECTED START-UP OR ELECTRICAL
SHOCK, UNPLUG THE POWER CORD BEFORE ATTEMPTING INSPECTION OR
MAINTENANCE. DO NOT USE A DAMAGED CUT-OFF SAW.
Brush inspection and replacement
Replace both carbon brushes when either has less than 1/4" of carbon remaining. To inspect
or replace, unplug the cut-off saw, remove the carbon brush cap on the side of the motor
housing, and pull out the brush (Note: the cap is spring-loaded). Repeat the steps on the
other side. To reassemble, reverse the procedure.
Fig. 13
Replace the laser module batteries (Fig. 13)
1. Remove the 3 screws that secure the laser
module cover to the housing. Remove the cover,
taking care not to damage the wires connected to
2
the laser switch.
2. Remove the 2 screws (1) that secure the battery
1
cover to the battery case. Remove the battery
cover.
3. Replace both "AAA" batteries (2).
WARNING: NEVER USE FLAMMABLE OR COMBUSTIBLE SOLVENTS AROUND THIS
CUT-OFF SAW. WHEN SERVICING, USE ONLY IDENTICAL ATD REPLACEMENT PARTS.
USE OF ANY OTHER PARTS MAY CREATE A HAZARD OR CAUSE PRODUCT FAILURE.
Lubrication
ATD tools are properly lubricated at the factory and are ready to use. When necessary,
lubricate only those parts that pivot or move with a dry silicone spray. Lubricating
motor bearings and other internal parts should be done only by qualified service technicians.
General maintenance
Before each use, inspect the guards, switches, power cord, and extension cord. Check for
loose screws, jamming, improper mounting, broken parts, and any other condition that may
affect the safe operation of the cut-off saw. If an unusual operating noise or vibration occurs,
turn the cut-off saw OFF and immediately correct the problem before using the cut-off saw
again.
Cleaning
Clean dust and debris from vents, tabletop, and vise screw. Use a dry, clean rag to clean all
areas of the cut-off saw. Never use solvents or other harsh chemicals for cleaning as they
are harmful to plastic and other insulated parts. Petroleum-based products, brake fluid,
thinners and ammonia detergents will also permanently damage the cut-off saw.
13
IX. Replacement parts
WARNING: ALL ELECTRICAL OR MECHANICAL REPAIRS SHOULD BE ATTEMPTED
ONLY BY A QUALIFIED SERVICE TECHNICIAN. USE ONLY IDENTICAL REPLACEMENT
PARTS. ANY OTHER PARTS MAY CREATE A HAZARD.
14
IX. Replacement parts ... continued
No.
Part no.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
PRT10515-01
PRT10515-02
PRT10515-03
PRT10515-04
PRT10515-05
PRT10515-06
PRT10515-07
PRT10515-08
PRT10515-09
PRT10515-10
PRT10515-11
PRT10515-12
PRT10515-13
PRT10515-14
PRT10515-15
PRT10515-16
PRT10515-17
PRT10515-18
PRT10515-19
PRT10515-20
PRT10515-21
PRT10515-22
PRT10515-23
PRT10515-24
PRT10515-25
PRT10515-26
PRT10515-27
PRT10515-28
PRT10515-29
PRT10515-30
PRT10515-31
PRT10515-32
PRT10515-33
PRT10515-34
PRT10515-35
PRT10515-36
PRT10515-37
PRT10515-38
PRT10515-39
PRT10515-40
PRT10515-41
PRT10515-42
PRT10515-43
PRT10515-44
PRT10515-45
PRT10515-46
PRT10515-47
PRT10515-48
PRT10515-49
PRT10515-50
PRT10515-51
PRT10515-52
POWER CORD
POWER CORD SHEATH
SCREW
CARRY HANDLE (L)
SPRING WASHER
CARRY HANDLE (R)
SCREW
FLAT WASHER
SCREW
SCREW
LEFT SIDE PANEL
SWITCH TRIGGER
NUT
SWITCH,HY18
D-HANDLE (UP)
CIRCUIT BREAKER
RIGHT SIDE PANEL
SCREW
FLAT WASHER
SCREW
STRAIN RELIEF
WIRE NIP
SCREW
D-HANDLE (DOWN)
SCREW
BRUSH CAP
BRUSH HOLDER
SPRING
CARBON BRUSH
SCREW
ARM
WIRE BUSH
GEAR WASHER
SCREW
STATOR ASSEMBLY
FLAT WASHER
SPRING WASHER
SCREW
BEARING
ROTOR ASSEMBLY
FAN BEARING
FAN RING
LOCK PIN
LOCK PIN KNOB
SPRING
GEAR BOX
BEARING, 6000
C-RING
BIG GEAR
SLEEVE
KEY
SHAFT
Qty
No.
Part no.
Description
1
1
4
1
22
1
4
25
4
2
1
1
3
1
1
1
1
6
3
3
1
1
1
1
4
2
2
2
2
2
1
1
1
1
1
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
PRT10515-53
PRT10515-54
PRT10515-55
PRT10515-56
PRT10515-57
PRT10515-58
PRT10515-59
PRT10515-60
PRT10515-61
PRT10515-62
PRT10515-63
PRT10515-64
PRT10515-65
PRT10515-66
PRT10515-67
PRT10515-68
PRT10515-69
PRT10515-70
PRT10515-71
PRT10515-72
PRT10515-73
PRT10515-74
PRT10515-75
PRT10515-76
PRT10515-77
PRT10515-78
PRT10515-79
PRT10515-80
PRT10515-81
PRT10515-82
PRT10515-83
PRT10515-84
PRT10515-85
PRT10515-86
PRT10515-87
PRT10515-88
PRT10515-89
PRT10515-90
PRT10515-91
PRT10515-92
PRT10515-93
PRT10515-94
PRT10515-95
PRT10515-96
PRT10515-97
PRT10515-98
PRT10515-99
PRT10515-100
PRT10515-101
PRT10515-102
PRT10515-103
PRT10515-104
PRT10515-105
BEARING,6004
C-RING
GEAR BOX COVER
INNER FLANGE
BLADE SLEEVE
SCREW
SPRING WASHER
FLAT WASHER
LASER COVER
LASER SWITCH
SCREW
BATTERY COVER
BATTERY SPRING 3
BATTERY
SCREW
BATTERY SPRING 1
BATTERY BOX
SCREW
LASER BASE
BATTERY SPRING 2
LASER
LASER PRESS BOARD
LASER JOINTER
JOINTER BASE
LASER GUARD
BLADE
OUTER FLANGE
SPACER WASHER
BLADE SCREW
SCREW
UPPER GUARD
GUARD STOP
LOCKNUT
LOCKNUT
LOWER GUARD
GUIDE WHEEL
BIG WASHER
HINGE
SPRING
SCREW
SCREW
SCREW
HINGE CAP
SCREW
DEPTH PLATE
DEPTH BOLT
WRENCH
WRENCH STORAGE CLIP
NUT
PIN CAP
C-RING
O-RING
NUT
15
Qty
1
1
1
1
1
3
7
5
1
1
6
1
1
2
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
3
1
5
1
1
1
2
2
1
1
1
1
IX. Replacement parts ... continued
ATD-10515 14" Cut-off Saw with Laser Guide
No. Part no.
Description
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
PIN 1
PIN 2
SCREW
NUT
DEPTH STOP BASE
BIG SPRING
ROTATION AXIS
C-RING
BASE
NUT
SPARK GUARD
FOOT CUSHION BASE
FOOT CUSHION
FLAT WASHER
FOOT CUSHION ASSEMBLY
HEX BOLT
SPRING WASHER
FENCE
PRT10515-106
PRT10515-107
PRT10515-108
PRT10515-109
PRT10515-110
PRT10515-111
PRT10515-112
PRT10515-113
PRT10515-114
PRT10515-115
PRT10515-116
PRT10515-117
PRT10515-118
PRT10515-119
PRT10515-120
PRT10515-121
PRT10515-122
PRT10515-123
Qty
No.
Part no.
Description
1
1
2
1
1
1
1
2
1
3
1
4
4
7
1
2
2
1
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
PRT10515-124
PRT10515-125
PRT10515-126
PRT10515-127
PRT10515-128
PRT10515-129
PRT10515-130
PRT10515-131
PRT10515-132
PRT10515-133
PRT10515-134
PRT10515-135
PRT10515-136
PRT10515-137
PRT10515-138
PRT10515-139
C-RING
PIN
CLAMP
LOCKNUT
SCREW
SPRING PIN
BOLT
SPRING WASHER
FLAT WASHER
NUT
NUT BASE
SPRING PIN
WHEEL
NUT
HANDLE
BOLT
16
Q ty
1
1
1
1
1
1
2
2
3
1
1
1
1
1
1
1
Download PDF

advertising