Specifications | ATD Tools atd-5928 Automobile Battery Charger User Manual

ATD-5928
RECHARGEABLE 12 VOLT 22 AMP/HOUR JUMP START
OWNERS MANUAL
• 1700 PEAK AMPS/700 CRANKING AMPS OF STARTING POWER.
• STARTS CARS, TRUCKS, RV’s AND BOATS WITHOUT THE NEED OF ANOTHER VEHICLE OR AC POWER CORDS.
• 12V DC SOCKET WITH OVERLOAD PROTECTION PROVIDES POWER FOR ANY 12V APPLIANCE.
• PROVIDES UP TO 50-HOURS OF DC POWER WHEN USED WITH 12V DC APPLIANCES.
• ALLOWS 12V DC APPLIANCES TO BE USED IN REMOTE SITES AND/OR IN EMERGENCIES WHEN COMMERCIAL POWER IS NOT AVAILABLE.
• SOLID-STATE, AUTOMATIC OPERATION AND CIRCUIT PROTECTION.
• REQUIRES NO MAINTENANCE FOR OPTIMUM OPERATION.
• SEALED, MAINTENANCE-FREE, HEAVY-DUTY BATTERY IS SAFE TO USE AND TRANSPORT.
• CAN BE STORED IN ANY POSITION WITHOUT RISKING ACID LEAKAGE.
• 74” HEAVY-DUTY 4 GAUGE COPPER CABLES CAN CARRY MORE AMPERAGE THAN SIMILAR UNITS.
• EASY TO READ COLOR CODED BATTERY METER.
• DC POWER CORD ALLOWS RECHARGING FROM 12V DC SOCKET.
• EXTERNAL 120V AC/12V DC CHARGING ADAPTER WITH AN AUTOMATIC CUT-OFF TO PREVENT OVERCHARGING.
• MOLDED HIGH-IMPACT CASE IS TOUGH AND DURABLE.
Made in China
To ATD Specifications
INTRODUCTION
YOUR POWER PACK UNIT IS DESIGNED AS A COMPACT, DURABLE AND PORTABLE JUMP START SYSTEM FOR 12 VOLT DC VEHICLES
AND BOATS. THIS SELF-CONTAINED SYSTEM WILL START MOST VEHICLES AND BOATS WITHOUT THE NEED FOR A HOST VEHICLE OR
120V AC POWER SUPPLY. THIS SYSTEM CAN ALSO BE USED AS A SAFE, PORTABLE SOURCE OF 12V DC ELECTRIC POWER IN REMOTE
LOCATIONS AND/OR IN EMERGENCIES.
THE POWER PACK UNIT HAS AN EASY-TO-READ, COLOR-CODED BATTERY METER THAT INDICATES CHARGE LEVEL. A 12V DC SOCKET
IS PROVIDED FOR USE WITH APPLIANCES THAT WOULD OPERATE FROM A VEHICLES CIGARETTE LIGHTER OR 12V DC SOCKET. THIS
ALLOWS MAXIMUM PORTABILITY AND UTILITY WHEN YOUR POWER PACK UNIT IS USED IN REMOTE LOCATIONS.
FOR MAXIMUM CONVENIENCE, YOUR POWER PACK UNIT CAN BE RECHARGED FROM A 120V AC POWER SOURCE. EXTERNAL 1000 mA
RECHARGER/CONVERTER HAS AN AUTOMATIC CUT-OFF THAT PREVENTS OVER CHARGING THE BATTERY. A RED TEST SWITCH
SHOWS THE BATTERY CONDITION ON THE METER. A COVERED 12V DC SOCKET IS PROVIDED.
NOTE: ON/OFF SWITCH ONLY CONTROLS POWER TO THE 2 BATTERY CLAMPS. WE SUGGEST YOU KEEP THIS SWITCH IN THE "OFF"
POSITION FOR ALL OPERATIONS OTHER THAN JUMP STARTING A CAR.
FIGURE 1.
WARNINGS
• ALWAYS WEAR EYE PROTECTION WHEN WORKING ON OR AROUND LEAD-ACID BATTERIES.
IF SPLASHED WITH BATTERY ACID: IMMEDIATELY FLUSH AFFECTED AREA SUCH AS FACE AND PARTICULARLY THE EYES WITH
CLEAN WATER. CONTINUE FLUSHING FACE AND EYES UNTIL MEDICAL HELP ARRIVES.
• LEAD-ACID BATTERIES GENERATE HYDROGEN GAS DURING NORMAL OPERATION. MORE GAS IS GENERATED WHEN THE BATTERY IS
CHARGING. HYDROGEN GAS IS:
1. EXPLOSIVE
2. POISONOUS TO BREATHE
3. HIGHLY FLAMMABLE
• TO AVOID POSSIBLE DAMAGE THAT MAY SHORTEN THE UNITS WORKING LIFE, PROTECT THIS UNIT FROM DIRECT SUNLIGHT,
DIRECT HEAT, AND /OR MOISTURE.
• THIS SYSTEM IS DESIGNED TO BE USED ONLY ON VEHICLES OR BOATS WITH 12-VOLT ELECTRICAL SYSTEMS.
• THIS SYSTEM IS NOT DESIGNED TO BE USED AS A REPLACEMENT FOR A VEHICLE BATTERY.
TO AVOID AN EXPLOSION AND/OR THE POSSIBILITY OF BEING SPLASHED WITH BATTERY ACID:
• NEVER ALLOW THE RED AND BLACK CLAMPS TO TOUCH EACH OTHER OR FOR BOTH TO TOUCH THE SAME METAL OBJECT OR ANY
ELECTRICALLY CONDUCTIVE MATERIAL FOR THAT MATTER.
• ONLY ATTEMPT TO JUMP START A VEHICLE OR BOAT IN A WELL VENTILATED AREA.
• ALWAYS CONNECT THE RED (+) CLAMP TO THE POSITIVE (+) BATTERY TERMINAL FIRST.
• CONNECT THE BLACK (-) CLAMP TO A NON-MOVING METAL PART ON THE ENGINE NOT TO THE NEGATIVE (-) BATTERY TERMINAL.
RECOMMENDATIONS FOR GETTING THE MOST FROM YOUR NEW POWER PACK UNIT
RECHARGING
1. FOR MAXIMUM BATTERY LIFE, WE RECOMMEND THAT YOUR POWER PACK UNIT BE KEPT FULLY CHARGED AT ALL TIMES. IF THE
BATTERY IS ALLOWED TO REMAIN IN A DISCHARGED STATE, BATTERY LIFE WILL BE SHORTENED.
TABLE I SHOWS THE RELATIONSHIP OF THE FREQUENCY OF USE BETWEEN RECHARGING AND THE EXPECTED NUMBER OF
CHARGE/RECHARGE CYCLES.
TABLE I. ‐ BATTERY LIFE NUMBER OF JUMP‐STARTS BETWEEN RECHARGING DISCHARGE AND RECHARGE CYCLES 1 5 10 1000+ 700+ 500+ 2. THE TIME REQUIRED TO FULLY RECHARGE YOUR POWER BOOSTER AFTER JUMP-STARTING AN ENGINE IS A FUNCTION OF HOW
MANY JUMP-STARTS ARE PERFORMED BETWEEN RECHARGING SESSIONS. TABLE II SHOWS THE APPROXIMATE RECHARGING TIMES
YOU CAN EXPECT.
TABLE II. ‐ RECHARGING TIMES VS. JUMP‐STARTS NUMBER OF RECHARGING NUMBER OF RECHARGING JUMP‐STARTS TIME (IN HOURS) JUMP‐STARTS TIME (IN HOURS) 1 8 4 32 2 16 5 40 3 24 6 48 3. CHECK THE CHARGE IN YOUR POWER PACK UNIT OFTEN BY DEPRESSING THE RED PUSH-BUTTON SWITCH.
THE METER WILL SHOW THE BATTERY CHARGE.
120V AC/12V DC CHARGING :
PLUG THE 120V AC/12V DC CHARGING ADAPTER INTO A WALL OUTLET AND INTO THE RECEPTACLE ON YOUR NEW POWER PACK UNIT.
CHARGE THIS DEVICE FOR AT LEAST 4 HOURS OR UNTIL THE METER SHOWS A FULL (14- TO 15-V DC) CHARGE WHEN THE RED ROCKER
SWITCH IS DEPRESSED. THE RECHARGING CONVERTER CIRCUIT UNIT HAS AN AUTOMATIC CUT-OFF CIRCUIT SO THE INTERNAL
BATTERY CANNOT BE OVERCHARGED. TO RECHARGE YOUR POWER PACK UNIT BATTERY FROM 120V AC FOLLOW THESE STEPS :
1. PULL THE PLUG COVER FROM THE ROUND RECEPTACLE.
2 . THE EXTERNAL CHARGER FURNISHED WITH YOUR POWER BOOSTER HAS A 120V AC PLUG AT ONE END AND A 12V DC CIGARETTE
PLUG AT OTHER END. PLUG THE 120V AC PLUG INTO 120V AC WALL OUTLET AND THE OTHER INTO THE RECEPTACLE ON THE FRONT
PANEL OF YOUR POWER BOOSTER, CHARGING IS IN PROGRESS.
3. PRESSING THE 'TEST' BUTTON WILL INDICATE THE LEVEL OF CHARGE. THE EXTERNAL CHARGER HAS THE AUTOMATIC CUT-OFF
THAT PREVENTS OVER CHARGING THE BATTERY.
4. CONTINUE TO CHARGE UNTIL THE VOLTMETER INDICATES FULL CAPACITY IN GREEN AREA WHEN THE TEST BUTTON IS PRESSED
IMPORTANT: DO NOT STOP CHARGING BEFORE THE METER INDICATES FULL CAPACITY IN GREEN AREA.
AT THIS POINT, ONCE THE CHARGER IS DISCONNECTED, THE VOLTAGE WILL SLOWLY SETTLE BACK TO READ 100%.
THIS IS QUITE NORMAL AND INDICATES THAT THE BATTERY IS AT FULL CAPACITY.
NOTE: TO FULLY CHARGE A BATTERY COULD TAKE UP TO 72 HOURS, DEPENDING UPON THE STATE OF DISCHARGE. THE UNIT CAN
REMAIN PLUGGED INTO THE POWER SOCKET INDEFINITELY AS THE INTERNAL PCB HAS AN AUTOMATIC "FLOAT CHARGING CIRCUIT"
WHICH WILL NOT ALLOW AN OVERCHARGE CONDITION OR DAMAGE TO THE BATTERY.
12V DC CHARGING:
YOUR NEW POWER PACK UNIT IS EQUIPPED WITH A RECEPTACLE THAT WILL ALLOW YOU TO RE-CHARGE THIS SYSTEM FROM THE 12V
DC SOCKET IN YOUR VEHICLE OR BOAT.
NOTE : WE RECOMMEND THAT YOU USE THE 12V DC RECHARGING PROCEDURE ONLY WHEN IT IS NECESSARY,
AS CONTINUED USE OF THE 12V DC RECHARGING PROCEDURE MAY SHORTEN THE SYSTEM'S LIFE.
TO USE THE 12V DC RECHARGING SYSTEM :
1. INSERT THE POWER CORD WITH THE 12V DC PLUG INTO THE 12V DC RECEPTACLE ON YOUR VEHICLE OR BOAT.
2. INSERT THE PLUG AT THE OTHER END OF THIS POWER CORD INTO THE RECEPTACLE ON THE FRONT PANEL OF YOUR POWER
BOOSTER.
OPERATION
TO USE YOUR POWER PACK UNIT AS A 12V DC POWER SOURCE:
1. LIFT UP THE COVER OF THE 12V DC RECEPTACLE.
2. INSERT THE 12V DC PLUG FROM THE APPLIANCE INTO THE 12V DC RECEPTACLE.
Note: ON/OFF SWITCH CAN BE LEFT IN THE “OFF” POSITION
TABLE III. WILL GIVE YOU AN IDEA OF WHAT OPERATION TIME YOU CAN EXPECT WHEN STARTING FROM A FULLY CHARGED SYSTEM.
TABLE III. POWER PACK UNIT AS A 12V DC POWER SOURCE ESTIMATED ESTIMATED POWER USAGE CONSUMPTION TIME APPLIANCE TYPE (IN WATTS) (IN HOURS) FLUORESCENT LIGHTS, CELL PHONES 4 30 RADIOS, FANS, DEPTH FINDERS 9 21 CAMCORDERS, VCR'S, SPOTLIGHTS 15 12 ELECTRIC TOOLS, BILGE PUMPS 24 7 ELECTRIC COOLERS 48 3 AIR COMPRESSORS, CAR VACUUMS 80 1.5 TABLE IV WILL GIVE YOU AN IDEA OF WHAT OPERATION TIME YOU CAN EXPECT WHEN STARTING FROM A FULLY CHARGED SYSTEM.
WHEN USING YOUR POWER PACK UNIT AS A 120 V AC POWER SOURCE WITH A POWER INVERTER.
TABLE IV. POWER PACK UNIT AS A 12V DC POWER SOURCE WITH POWER INVERTER ESTIMATED ESTIMATED POWER USAGE CONSUMPTION TIME APPLIANCE TYPE (IN WATTS) (IN HOURS) SPOTLIGHTS, SUMP PUMPS, & VCR'S 100 1.5 FAXES, TV'S SMALL APPLIANCES 150 1 COMPUTERS , PRINTERS 200 0.75 MEDIUM POWER TOOLS, BLENDERS 250 0.5 JUMP-STARTING:
FOR OPTIMUM PERFORMANCE, WHEN USING YOUR POWER PACK UNIT TO JUMP START A VEHICLE OR BOAT, PLEASE READ AND
FOLLOW
THESE STEP-BY-STEP INSTRUCTIONS:
1. SWITCH THE ENGINE OF THE VEHICLE OR BOAT TO BE JUMP-STARTED TO “OFF”.
2. CONNECT THE RED (+) “ALLIGATOR” CLAMP TO THE RED (+) POSITIVE BATTERY TERMINAL.
3. CONNECT THE BLACK (-) “ALLIGATOR” CLAMP TO A NON-MOVING METAL PART OF THE ENGINE, NOT TO THE (-) NEGATIVE BATTERY
TERMINAL.
4. TURN POWER PACK UNIT SWITCH TO “ON”.
5. WAIT A MINUTE OR TWO TO LET THE VEHICLE BATTERY TO CHARGE
6. TRY TO START THE VEHICLE BUT DO NOT TRY FOR MORE THAN 5 TO 6 SECONDS.
7. IF THE VEHICLE OR BOAT ENGINE DOES NOT START, WAIT AT LEAST 3 MINUTES BEFORE TRYING AGAIN.
*UNDER NO CIRCUMSTANCES ALLOW THE RED AND BLACK CLAMPS TO TOUCH EACH OTHER OR A COMMON CONDUCTOR*
ONCE THE ENGINE IS RUNNING, FIRST DISCONNECT THE BLACK (-) CLAMP AND RETURN THIS CABLE TO ITS STORED POSITION ON THE
POWER PACK UNIT, THEN DISCONNECT THE RED (+) CLAMP AND RETURN THIS CABLE TO ITS STORED POSITION ON THE POWER PACK
UNIT. AS SOON AS POSSIBLE, CONNECT YOUR POWER PACK UNIT SYSTEM TO 120-VAC AND RECHARGE.
BATTERY REPLACEMENT
FIGURE 2. - REAR VIEW OF THE POWER PACK UNIT SHOWING THE BATTERY COMPARTMENT
1. UNSCREW AND REMOVE THE EIEVEN (11) PHILLIPS HEAD SCREWS THAT HOLD THE REAR COVER IN PLACE ON THE BACK OF YOUR
POWER PACK UNIT.
2. LIFT OFF THE COVER PLATE TO EXPOSE THE BATTERY COMPARTMENT.
3. LIFT THE BATTERY OUT OF THE BATTERY COMPARTMENT.
4. DETACH THE #4 JUMPER CABLES AND THE RED AND BLACK RECHARGING WIRES FROM THE BATTERY TERMINALS .
5. ENSURE THAT THE REPLACEMENT BATTERY IS ORIENTED WITH THE POSITIVE ON THE RIGHT SIDE AND THE NEGATIVE ON THE LEFT
SIDE, JUST AS THE OLD BATTERY CAME OUT.
6. CONNECT THE RED #4 JUMPER CABLE AND RED RECHARGING WIRE TO THE POSITIVE (+) BATTERY TERMINAL (ALSO MARKED WITH
RED),
THEN CONNECT THE BLACK #4 JUMPER CABLE AND RECHARGING WIRE TO THE NEGATIVE (-) BATTERY TERMINAL. DOUBLE CHECK ALL
CONNECTIONS, AND TIGHTEN.
7. SLIDE THE NEW BATTERY IN POSITION.
8. REPLACE THE BATTERY COMPARTMENT COVER AND SECURE IN PLACE WITH THE EIGHT (8) ''PHILLIPS'' (CROSS- HEAD) SCREWS.
SPECIFICATIONS
ITEM # . . . . . . . …. . . . . . . . . . . . . . . . . . . .ATD-5928
VOLTAGE . . . . . . . . . . . . . . . . . . . . . . . . . .12V DC
BOOST POWER . . . . . . . . . . . . . . . . . . . . .700 CRANKING AMPS
PEAK AMPS… …...…….. . . .. . . . . . . . . . .1700 AMPS
BATTERY TYPE . . . . . . . . . . . . . . . . . . . . .SEALED, LEAD- ACID, RECHARGEABLE, MAINTENANCE-FREE, 12V DC, 22-AMP-HOURS
BOOSTER CABLES . . . . . . . . . . . . . . . . . .74”, #4 AWG 100% COPPER CABLES WITH 1000 AMP "ALLIGATOR" CLAMPS
DIMENSIONS …. . . . . . . . . . . . . . . . . . .. . .40 x 37 x 13 CM
ATD-5928
12
14
13
11
10
7
8
9
6
5
18
19
15
4
3
ITEM#
1
2
3
4
5
6
7
8
9
10
1
2
ORDERING PART#
PRT5928-01
PRT5928-02
PRT5928-03
PRT5928-04
PRT5928-05
PRT5928-06
PRT5928-07
PRT5928-08
PRT5928-09
PRT5928-10
16
17
DESCRIPTION
FIXING BOARD, ON/OFF SWITCH
TEST SWITCH
KNOB, ON/OFF SWITCH
COVER, CIGARETTE
VOLTMETER
FRONT PANEL
FIXING BOARD, VOLTMETER
CIGARETTE LIGHTER SOCKET (INNER)
ON/OFF SWITCH
CLAMP, RED & BLACK WITH 4GA CABLE
ITEM#
11
12
13
14
15
16
17
18
19
ORDERING PART#
PRT5928-11
ATD5904
PRT5928-13
PRT5928-14
PRT5928-10
PRT5928-16
PRT5928-17
PRT5928-18-19
PRT5928-18-19
DESCRIPTION
CASE
BATTERY, 12V/22AH
BACK COVER
SCREW
CLAMP, RED & BLACK WITH 4GA CABLE
SCREW
RUBBER BASE
AC CHARGER, 110V 1000mA & DC CORD
AC CHARGER, 110V 1000mA & DC CORD
Download PDF

advertising