Operating instructions | ATD Tools ATD- 7371 Automobile Parts User Manual

Air Hydraulic
Bottle Jacks
Operating Instructions & Parts Manual
Model Number
ATD-7370
ATD-7371
ATD-7372
Capacity
12 Ton
20 Ton
20 Ton (low profile)
U.S. Patent No’s. 5,341,723 • 5,946,912
!
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
! advertencia
• Leer, comprender, y seguir las instrucciónes antes
de utilizar el aparato.
• El manual de instrucciónes y la información de
seguridad deben estar comunicado en lengua del
operador antes del uso.
• No seguir estas indicaciónes puede causar daños
personales o materiales.
! WARNING
To avoid crushing and related injuries:
NEVER work on, under or around a
load supported only by a hydraulic
jack. ALWAYS use adequately rated
jack stands.
ATD Tools Inc.
160 Enterprise Drive, Wentzville MO 63385
Printed in China
ATD7370-M2 rev 02/09
SAFETY and GENERAL INFORMATION
Save these instructions. For your safety, read, understand, and follow the information provided with and on this jack
before using. The owner and operator of this equipment shall have an understanding of this jack and safe operating
procedures before attempting to use. The owner and operator shall be aware that use and repair of this product
may require special skills and knowledge. Instructions and safety information shall be conveyed in the operator's
native language before use of this jack is authorized. If any doubt exists as to the safe and proper use of this jack,
remove from service immediately.
Inspect before each use. Do not use if broken, bent, cracked, or damaged parts (including labels) are noted. Any jack
that appears damaged in any way, operates abnormally or is missing parts, shall be removed from service immediately. If
the jack has been or suspected to have been subjected to a shock load (a load dropped suddenly, unexpectedly upon it),
immediately discontinue use until jack has been checked by an authorized factory service center (contact distributor or
manufacturer for list of Authorized Service Centers) . It is recommended that an annual inspection be done by qualified
personnel. Labels and Operator's Manuals are available from manufacturer.
PRODUCT DESCRIPTION
Air Actuated Hydraulic Bottle Jacks are designed to lift, not support, rated capacity loads consisting of one end of
a vehicle. Immediately after lifting, the load must be supported by a pair of appropriately rated jack stands. Ensure
that air source can dedicate 7.8 CFM @ 110-175 psi. A minimum of 150 psi air pressure is required to raise rated
capacity load.
Never use hydraulic jack as a stand alone device. After lifting, immediately support the lifted load
with a pair of appropriately rated jack stands. Never place any portion of your body under a load
when lifting or lowering the load.
!
SPECIFICATIONS
Model
Capacity
Base Size
(L x W)
Saddle
Diameter
Min.
Height
Max.
Height
Hydraulic Lift
Ext.
Screw
ATD-7370
12 Ton
8" x 6-1/2"
1-5/8"
9-1/2"
18-1/2"
5-1/2"
3-1/2"
ATD-7371
20 Ton
8-1/2" x 7-1/4"
2"
9-3/4"
18-3/4"
5-1/8"
3-7/8"
ATD-7372
20 Ton
8-1/2" x 7-1/4"
2"
8-1/8"
15-1/2"
4"
3-3/8"
Saddle/Extension Screw
Air Motor
Ram
Quick Coonnector (N/A for ATD-7372)
Air Hose
Oil Filler Screw/ Plug*
(*) oil filler plug for ATD-7370
Carry Handle
Lift Control Valve
Handle Sleeve
Release Valve
Handle
Figure 1 - Typical Air Bottle Jack Nomenclature
2
!
! WARNING
WARNING
X
• Study, understand, and follow all printed
materials provided with/on this product before use.
• Do not exceed rated capacity.
• This is a lifting device only!
• Immediately after lifting, support the load with
a pair of appropriately rated jack stands.
• Use only on hard, level surface.
• Do not use adapters or accessories that are not
provided initially.
• Lift only on areas of the vehicle as specified by
the vehicle manufacturer.
• Never wire, clamp or otherwise disable the lift
control valve to function by other than operator's
hand.
• No alterations shall be made to this product.
• Failure to heed these markings may result in
personal injury and/or property damage.
To avoid crushing and related injuries:
• Never work on, under or around a load supported
only by hydraulic jack.
• Always use adequately rated jack stands.
• Chock each unlifted tire in both directions.
• Do not use this device to lift, level, lower, support nor
move a house, mobile home, travel trailer, camper or
any building structure.
• Be alert and sober when using this product. Do not
operate under the influence of drugs or alcohol.
!
Be sure all tools and personnel are clear before lowering load. Only attachments and/or
adapters supplied by the manufacturer shall be used.
Lift only on areas of the vehicle as specified by the
vehicle manufacturer.
PREPARATION
Before Use
1. Verify that the product and application are compatible, if in doubt call ATD Technical Service (636) 327-9050.
2. Before using this product, read the operator's manual completely and familiarize yourself thoroughly with the
product, its components and recognize the hazards associated with its use.
3. Assemble handle, ensure spring clips align with slots.
4. To familiarize yourself with basic operation, use the notched end of provided handle to engage and turn the release
valve:
a. Clockwise until firm resistance is felt to further turning. This is the ‘CLOSED’ release valve position used to
raise the ram plunger.
b. Counter-clockwise, but no more than 1 turn from the closed position. This is the ‘OPEN’ release valve
position used to lower the ram plunger.
5. With ram fully retracted, locate and remove the oil filler plug/screw. Insert the handle into the handle sleeve, then
pump 6 to 8 strokes. Ensure the oil level is just below the oil filler hole. Reinstall the oil filler plug/screw.
6. Pour a teaspoon of good quality, air tool lubricant into the air supply inlet of the lift control valve. Connect to air
supply and squeeze lift control valve for 3 seconds to evenly distribute lubricant.
7. This product is equipped with the popular 1/4" NPT air coupler. When installing a different air coupler of your
choice, ensure that thread tape or compound is used when servicing connections. To ensure dependable, trouble
free operation an inline air dryer and oiler is recommended.
8. Check that the pump operates smoothly and that the extension screw will thread up/down easily before putting
into service. Replace worn or damaged parts and assemblies with ATD authorized replacement parts only.
Bleeding / Venting Trapped Air
With the release valve in the OPEN position (4b above) and with ram plunger fully lowered, locate and remove the
oil filler plug/screw. Insert the handle into the handle sleeve; then pump 6 to 8 full strokes. This will help release any
pressurized air which may be trapped within the reservoir. Oil level should be even with the bottom of the oil filler
hole. Reinstall the oil filler plug/screw.
!
Use only handle provided by jack manufacturer. The handle provided with this jack will safely engage the
release valve and operate the handle sleeve. If handle is worn, operates abnormally, or will not positively
engage the release valve, STOP, discontinue use of the jack until a factory replacement handle can be acquired.
!
Paint contains lead! DO NOT sand or grind painted surface!
3
OPERATION
Raising the Ram Plunger
1. Assemble handle, ensure that spring clips align with slots.
2. Place vehicle in the park, with emergency brake on and wheel securely chocked to prevent inadvertent vehicle
movement.
3. Locate and close release valve by turning handle clockwise until firm resistance is felt to further thread
engagement.
4. Verify lift point, center jack saddle under lift point.
5. Squeeze the lift control valve or insert handle into handle sleeve and pump to contact lift point. To lift, continue
pumping until load reaches desired height. DO NOT OPERATE BY AIR AND BY HAND PUMPING AT THE
SAME TIME.
6. Immediately transfer the lifted load to a pair of appropriately rated jack stands.
!
Do not use an extender on the air hose or the operating handle.
Lowering
Make certain that all personnel are clear of the load before lowering. Control the rate of descent of the
load at all times. The more you open the release valve, the faster the load descends.
!
1. Raise load high enough to clear the jack stands, then carefully remove jack stands (always used in pairs).
2. Slowly turn the handle counter-clockwise, but no more than 1 turn. If the load fails to lower:
a. Use another jack to raise the vehicle high enough to reinstall jack stands.
b. Remove the affected jack and then the stands. c. Lower the load by turning the release valve counter-clockwise, but no more than 1 turn.
3. After removing jack from under the load, push ram and handle sleeve down to reduce exposure to rust and
contamination.
MAINTENANCE
Important: Use only good grade hydraulic jack oil. Avoid mixing different types of fluid and NEVER use brake fluid,
turbine oil, transmission fluid, motor oil or glycerin. Improper fluid can cause premature failure of the jack and the
potential for sudden and immediate loss of load. We recommend Mobil DTE 13M or equivalent.
Adding oil
1. With ram plunger fully lowered and pump piston fully depressed, set jack in its upright, level position. Remove oil
filler plug/screw.
2. Fill with oil until just below the rim of the oil filler screw hole. Reinstall the oil filler plug/screw.
Changing oil
For best performance and longest life, replace the complete fluid supply at least once per year.
1. With ram plunger fully lowered and pump piston fully depressed, remove the oil filler plug/screw.
2. Lay the jack on its side and drain the fluid into a suitable container.
Note: Dispose of hydraulic oil in accordance with local regulations.
3. Fill with oil until just below the rim of the oil filler hole. Reinstall the oil filler plug/screw.
Lubrication
1. A periodic coating of light lubricating oil to pivot points will help to prevent rust and assure that pump assemblies
move freely.
2. Air pump should be internally lubricated before each use. Use good quality air tool lubricant. If no inline oiler
is used, pour a teaspoon of air tool oil into the air control valve inlet. Operate the jack with air pressure to fully
distribute the oil inside the air motor.
Cleaning
Periodically check the pump piston and ram for signs of rust/corrosion. Clean as needed and wipe with oily cloth.
Note: Never use sandpaper or abrasive material on these surfaces!
Storage
When not in use, store the jack with pump piston and ram plunger fully retracted and air supply disconnected.
4
TROUBLESHOOTING
Symptom
Possible Causes
Corrective Action
Jack will not lift load
• Release valve not tightly closed
• Overload condition
• Air pressure inadequate
• Ensure release valve tightly closed.
• Remedy overload condition.
• Ensure adequate air pressure.
Jack will lift, but not maintain
pressure
• Release valve not tightly closed
• Overload condition
• Hydraulic unit malfunction
• Ensure release valve tightly closed.
• Remedy overload condition.
• Contact ATD Tech. Service.
Jack will not lower after
unloading
• Reservoir overfilled
• Ensure load is removed, then drain
fluid to proper level.
Poor lift performance
• Fluid level low
• Air trapped in system
• Ensure proper fluid level.
• With ram fully retracted, remove oil
filler plug/screw to let pressurized air
escape, then reinstall oil filler plug/
screw.
Will not lift to full extension
• Fluid level low
• Ensure proper fluid level.
ONE YEAR LIMITED WARRANTY
For a period of one (1) year from date of purchase, ATD Tools Inc. will repair or replace, at its option, without
charge, any of its products which fails due to a defect in material or workmanship under normal usage. This limited
warranty is a consumer's exclusive remedy.
Performance of any obligation under this warranty may be obtained by returning the warranted product,
freight prepaid, to ATD Tools Inc. Warranty Service Department, 160 Enterprise Drive, Wentzville, MO 63385.
Except where such limitations and exclusions are specifically prohibited by applicable law, (1) THE
CONSUMER'S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE
PRODUCTS AS DESCRIBED ABOVE. (2) ATD Tools Inc. SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL
OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER. (3) ANY IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED TO ONE YEAR, OTHERWISE THE REPAIR, REPLACEMENT OR REFUND AS
PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER,
AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. (4) ANY MODIFICATION,
ALTERATION, ABUSE, UNAUTHORIZED SERVICE OR ORNAMENTAL DESIGN VOIDS THIS WARRANTY AND
IS NOT COVERED BY THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not
apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
5
REPLACEMENT PARTS
(refer to page 6 & 7)
Not all components of the jack are replacement items, but are illustrated as a convenient reference of parts location.
When ordering parts, give part number and parts description. Call or write for current pricing: ATD Tools Inc. 160
Enterprise Drive, Wentzville, MO 63385. Tel:(636)327-9050 Fax:(636)327-9044
Replacement Parts Illustration for model ATD-7370, ATD-7371, & ATD-7372
23
25
10
10
a
1
11
8
9
21
b
c
2
8
12
12
22
792)
19
7230
8
D1
T
l
A
l e
deod
o
m
r
m
o
24
for(f
k
d
18
17
e
3b
g
3a
22
16
f
15
j
7
i
l
14
4
13
h
5
7
6
20
g
Figure 2 - Replacement Parts Illustration for Model ATD-7370, ATD-7371, & ATD-7372
6
Replacement Parts List for model ATD-7370, ATD-7371 & ATD-7372
Item
Part# for ATD-7370 Part# for ATD-7371 Part# for ATD-7372 Description
Qty.
1
A120-10004-000
A190-10002-000
Cylinder Fastener
1
2
A120-10003-000
A190-10001-000
Guide Ring
1
3a
5905-00100-200
N/A
Filler Plug
1
3b
N/A
G62S-03301-000
Filler Screw
1
4
A120-10002-000
Special Washer
2
5
5905-00054-000
Seal
1
6
BT10-24001-000
Release Valve
1
Gasket
2
Air Motor
1
Air Inlet Swivel
1
Hose Assy.
1
A20060-0006
Air Hose
1
12
A20060-0007
Lift Control Valve
1
13
B020-15002-000
Washer
1
14
B080-15001-000
Pump Cylinder
1
15
A120-15101-000
Pump Piston
1
16
5115-08033-000
Bolt
1
17
5405-07024-000
Pin
1
18
A120-13000-000
Handle Socket
1
19
5405-02018-000
Snap Pin
1
20
B10N-21000-000
Handle Assembly
1
Air Coupler, Female 1/4 NPT
1
A20060-0016
Air Coupler, Male 1/4 NPT
1
23
A27010-0008
Piston, Air Motor
1
24
5206-00008-001
Nut
1
Seal Kit (includes #4a, 6 & a~l)
-
Seal Kit, Air Motor
-
Label
1
Manual
1
7
5308-00095-000
8
A27010-0001
A27060-0003
9
A27010-0002
N/A
10
A20060-0005
A20060-0015
11
21
A27010-0011
22
*
A1206S-046
-
N/A
A1906S-047
A27010-0000
ATD7370-L0
-
ATD7371-L0
ATD7372-L0
ATD7370-M2
(*) Seal Kit Contents:
Item
3a
5
a
b
c
d
e
Description
Filler Plug (for ATD-7370 only)
Seal
Dust Wiper
O-ring
O-ring
Ram Bearing
Back-up Ring
Item
f
g
h
i
j
k
l
Qty.
1
1
1
1
1
1
1
Description
U-cup
O-ring
Packing
Oil Seal
O-ring
Ram Bearing (for ATD-7371 & ATD-7372)
O-ring (for ATD-7371 & ATD-7372)
(*)- Items included and available only as Seal Kit. Replacement requires special skills, knowledge, and
equipment. Only an authorized service center may perform the repair and/or replacement of these items.
Contact ATD technical service for list of service centers.
7
Qty.
1
2
1
1
1
1
1
ATD Tools Inc.
160 Enterprise Drive,
Wentzville MO 63385
636-327-9050
8
Download PDF

advertising