User manual | Atlantis Land 500 Digital Camera User Manual

Before you use this Product
This Atlantis Land product has been designed with safety in mind. However, if not used properly electrical
products can cause fires which may lead to serious body injury. To avoid such accidents, be sure to heed the
following.
Legal Caution
Video and audio surveillance can be forbidden by laws that vary from country to country. Check the laws in your
local region before using this product for surveillance purposes.
Heed the safety precautions
Be sure to follow the general safety precautions and the “Operation Notice.”
In case of a breakdown
In case of system breakdown, discontinue use and contact your authorized Atlantis Land dealer.
In case of abnormal operation
• If the unit emits smoke or an unusual smell,
• If water or other foreign objects enter the cabinet, or
• If you drop the unit or damage the cabinet:
1 Disconnect the cable and the connecting cables.
2 Contact your authorized Atlantis Land dealer or the store where you purchased the product.
Operation Notice - Operating or storage location
Avoid operating or storing the camera in the following locations:
• Extremely hot or cold places (Operating temperature: 0 °C to +50 °C [32 °F to 122°F])
• Exposed to direct sunlight for a long time, or close to heating equipment (e.g., near heaters)
• Close to sources of strong magnetism
• Close to sources of powerful electromagnetic radiation, such as radios or TV transmitters
• Locations subject to strong vibration or shock
Ventilation
To prevent heat buildup, do not block air circulation around the device.
Transportation
When transporting the camera, repack it as originally packed at the factory or in materials of equal quality.
Cleaning
• Use a soft, dry cloth to clean the external surfaces of the device. Stubborn stains can be removed using a soft
cloth dampened with a small quantity of detergent solution, then wipe dry.
• Do not use volatile solvents such as alcohol, benzene or thinners as they may damage the surface.
2
Index
Installation ........................................................... 1
Using IP Camera via Mobile Phone ................... 2
Using IP Camera via Web Browser ................... 3
1. Initial accessing the IP camera ......................................................................................... 5
2. Configuration of Main Menu ............................................................................................. 6
2.1 Setting ...................................................................................................................... 6
2.2 Client Setting ........................................................................................................... 7
2.3 Image Setup ............................................................................................................. 7
2.4 Live View .................................................................................................................. 7
Setting .................................................................................................................................... 9
3. Basic ................................................................................................................................... 9
3.1 System ...................................................................................................................... 9
3.2 Camera ................................................................................................................... 13
3.3 Network .................................................................................................................. 20
3.4 Security .................................................................................................................. 27
4. Advance ............................................................................................................................ 29
4.1 FTP Client ............................................................................................................... 29
4.2 SMTP....................................................................................................................... 35
4.3 HTTP Event ............................................................................................................ 40
4.4 Schedule................................................................................................................. 42
4.5 Motion Detection.................................................................................................... 43
4.6 System Log ............................................................................................................ 45
Installation
Installation Steps
Follow these steps to install the NetCamera on your Ethernet:
1. Check the package contents against the list below.
2. Set the device. See IP Installer User Manual on the available methods.
Package Contents
Item
IP Camera
Power Adapter
CD
Camera Stand
Printed Document
Description
Atlantis Land IP Camera
External 5V 1A
User Manual / Software
Supplied with mounting screw
Quick Installation Guide
Overview
Front:
Body
Built-In Mic
Camera Stand
Rear:
Camera Stand Thread
Power In
Reset
Network
Audio Out
1
Using IP Camera via Mobile Phone
To use IP cameras via mobile phones, please make sure your RTSP is set to “ON”.
(Default is “ON”) To change the settings of IP cameras, please see “Settings” for details.
3G Mobile Phone viewing
For 3G mobile phone viewing, type “rtsp://<IP>:<PORT>/video.3gp” into your 3G web
browser. <IP> is the IP address of your IP camera, <PORT> is the RTSP port of your IP camera
(Default value is 8554.)
Example: rtsp://100.10.10.1:8554/video.3gp
Note:
• You can also use RTSP clients (RealPlayer, MPlayer, Windows Media Player,
Quicktime…etc.) to view RTSP streaming, just type in “rtsp://<IP>:<PORT>/video.3gp” as
the Player’s URL
2.5G Mobile Phone viewing
For 2.5G mobile phone viewing, type “<IP>/mobile.wml” into your 2.5G web browser. <IP> is
the IP address of your IP camera.
2
Using IP Camera via Web Browser
System Requirement
To use the product normally, we strongly recommend your computer follows our minimum
system requirement (Computer level lower than this might cause some problems)
Item
Requirements
CPU
Pentium 4 1600MHz (or equivalent AMD)
Graphic Card
64MB RAM graphic cards (or equivalent on-board graphic cards)
RAM
512MB
Operating System
Windows 98, ME (Please see Note)
Windows 2000, 2003, XP, Vista
Web Browser
Internet Explorer 6 or later
Note:
• If you’re using Windows 98 or ME, please install IP Installer before using WEB UI to ensure
the system runs normally.
3
How to Use
This chapter introduces how to monitor the image from the device using Microsoft web
browser. The Atlantis Land IP camera can be used with Microsoft web browsers and
Intelligent IP Installer in Windows operation systems. This document focuses on introducing
you to Microsoft web browser. The recommended browser for Windows is Internet Explorer
6.0. If you want to know how to use Atlantis Land IP camera with Intelligent IP Installer, check
Intelligent IP Installer User’s Manual in Windows operation systems.
The functions of the device should be set by the Administrator. For further instructions on
setting the device, see “Setting the Camera” .
4
1. Initial accessing the IP camera
1. Start your web browser, and enter the IP address or host name of the ATLANTIS LAND IP
camera in the Location / Address field of your browser.
Note:
• If you only want to view the video without setting page, enter “http://<IP>/index2.htm”
as your web URL.
2. Use the default account “admin” and default password “admin”.
Note:
• The default user name “admin” and the password are set at the factory for the
administrator. You can change them in the Account Menu under Setting on page 19.
3. The monitor image will be displayed in your browser.
5
2. Configuration of Main Menu
Language
You can click the pulldown box to select system language, including English, Traditional
Chinese, Simplified Chinese, German, Japanese and Spanish.
2.1 Setting
This function is only for the Administrator. Click this button to get into the Basic and Advance
settings menu.
6
2.2 Client Setting
Mode: Click the pulldown box to choose between MPEG4 and MJPEG video compression
mode.
Note:MJPEG streaming is unavailable if RTSP mode is ON.
View Size: Select the desired display image resolution to 640X480 or 320X240.
Protocol: Select the transferring protocol from TCP, UDP, HTTP and Multicast.
Video Buffer: Turn the Video Buffer function On/Off. The Video Buffer function makes the
streaming more smoothly in unsteady network environment, but might cause a little delay
in live viewing.
2.3 Image Setup
You can use the tool bar to optimize video brightness, contrast, and
saturation.
2.4 Live View
Snapshot:
You can capture a still image shot by the camera and save it in your computer.
1. Press
, and a snapshot window will appear.
2. Click “Save” to save the picture in your computer.
3. Click “Close” to return to the view page.
Zoom in / out the image via the monitor window
7
1. Clickk
to display
d
the digital zoo
om in windo
ow.
2. Pull the
to adjust the digital zzoom rang
ge, and it will
w
be sh
howed on the above window.
3. You can
c use the
e left click of your mo
ouse to mo
ove the
to any w
where on th
he window..
Audio buttons:
b
:S
Speakers turned on.
:M
Microphone
e turned on
n.
: Volume control bar.
:Speakers tu
urned off.
:M
Microphone
e turned offf.
Note:
•
It meanss the speakkers of you
ur compute
er are turne
ed on to tra
ansmit the sounds fro
om
d IP camerra(s). Similarly,
means
m
you
u can broad
dcast to the connecte
ed
the connected
c
via the Eth
hernet usin
ng your mic
crophone.
IP camera(s)
Video
o play butttons:
:Pause the
e current vid
deo
:Play the video.
v
c
vide
eo.
:Stop the current
he current vvideo.
:Record th
8
Setting
3. Basic
Click the “Basic” folder to display the sub folders, including System, Camera, Network,
and Security.
3.1 System
3.1.1 Information
The Information page provides you with product factory information, including Product
name, Firmware version, and Web version.
9
3.1.2 Day & Time
Current date & time:This displays the current date and time of the device.
PC clock:This displays the date and time of the monitoring PC clock.
Date & time format:Click the pulldown box to select among different time display formats,
including yyyy-mm-dd hh:mm:ss (year-month-day hour:minute:second), mm-dd-yyyy
hh:mm:ss
(month-day-year
hour:minute:second),
and
dd-mm-yyyy
hh:mm:ss
(day-month-year hour:minute:second).
Adjust:Select one of four time adjusting modes.
Keep current setting:Select this mode to keep the current date and time of the device.
Synchronize with PC:Select this mode to make the date and time of the device the same as
the monitoring PC.
Manual setting:Select this mode to manually adjust the date & time of the device.
Synchronize with NTP : Specify the NTP server name and the Refresh Interval to
synchronize the date and time of the device with those of the time server, known as the NTP
(Network Time Protocol) server.
Note:
• The NTP server (Network Time Protocol) is the time server which is an Internet
standard protocol (built on top of TCP/IP) that assures accurate synchronization to the
10
millisecond of computer clock times in a network of computers.
NTP server name:Type the host name or IP address of the NTP server, up to 64 characters.
Time zone:Select the time zone and time difference from Greenwich Mean Time in the area
where the device is installed from the pulldown box.
3.1.3 Initialize
Reboot:Click this button to reboot the device. A confirmation dialogue will appear. Click OK
to proceed. It takes about two minutes to reboot the device.
Factory default:Click this button to reset the device to the factory default settings. A
confirmation dialogue will appear. Click OK to proceed, the network indicator on the device
will start to blink. After completing adjustments to the default settings, the device will reboot
automatically. Do not turn off the device until the device reboots.
Backup setting data:Save the setting data of the device to a file. Click Save, and follow the
instructions on the browser to save the setting data file to your specified location.
Restore setting:Load the saved setting data of the device. Click Browse and select the file in
which the setting data is stored. Click OK, and the device is adjusted according to the loaded
data and restarted.
Firmware update:Upgrade the device software. Click Browse and select the file for
upgrading. A confirmation dialogue will appear. Click OK to start upgrading. The device will
reboot upon completion.
11
Note:
• Use only upgrade files that are special for this device. Problems may occur otherwise.
• Do not turn off the device power or disconnect the network until the upgrading is
completed.
12
3.2 Camera
3.2.1 General
RTSP: Switch the RTSP streaming On/Off.
Note:
• RTSP: Real Time Streaming Protocol. RTSP is supported by most of the media clients .
(RealPlayer, Media Player, QuickTime, etc…)
Image Rotate:Enables user to mirror or flip the display screen.
Night Mode:Turn Night Mode ON/OFF.
Lighting:Choose the lighting environment among 50Hz, 60Hz and Outdoor.
White Balance : Choose the white balance to Auto, Fluorescent, Incandescent and
Black&White.
Overlay:Select to add Text Overlay or Privacy Mask on/off the display screen.
Text Overlay:Enables users to see some information on the display screen, including
Date/Time and user-defined text. You can also change the background color.
Privacy Mask:Enables users to conceal an area of the video image.
13
3.2.2 MPEG4
3.2.2.1 Computer View
RTSP (If RTSP mode is ON)
RTSP port: Specify the transmission port number of RTSP streaming video. Default
value is 554.
Viewer authentication: If the viewer authentication is ON, users viewing through RTSP
will be requested to key-in username and password.
RTP (If RTSP mode is ON)
Unicast streaming:
Unicast streaming Video/Audio port range: Specify the transmission port range of
RTP streaming video. RTP will select a port randomly from the range.
Multicast streaming:
Multicast address: Specify the multicast server address.
Video / Audio Port: Specify the transmission port number of the video data. Specify an
even number from 1024 to 65534.
Time-To-Live: Set the maximum TTL that multicast can pass through.
14
MPEG4 viewer port (If RTSP mode is OFF)
Unicast streaming Video/Audio port number : Specify the transmission port number of the
video data. It is initially set to 8090. Specify an even number from 1024 to 65534.
Image Size:Specify the image size the network camera transmits. You can choose among
704 × 480, 352 × 240 and 176 × 120 for NTSC mode and 704 × 576, 352 × 288 and 176 ×
144 for PAL mode.
Frame rate:Set the frame rate of the MPEG4 image. Selectable values are 5, 10, 15, 20, 25,
30 fps. The unit “fps” stands for “frames sent per second”.
Quality
Auto:The quality and bitrate will be automatically decided according to the frame rate.
Fixed Quality:The selectable values are Medium, Standard, Good, Detailed and Excellent.
Fixed Bitrate:Set the bit rate of MPEG4 image transmission for a line. Selectable values are
64, 128, 256, 384, 512, 768, 1024, 1280, 1536 and 2048 kbps.
Note:
• The selected frame rate and bit rate are a tentative value. The actual frame rate and bit
rate may be different according to the image size, the shooting scene or the network
condition.
15
3.2.2.2 Mobile View
RTSP (If RTSP mode is ON)
RTSP port: Specify the transmission port number of RTSP streaming video. Default
value is 8554.
RTP (If RTSP mode is ON)
Unicast streaming:
Unicast streaming Video/Audio port range: Specify the transmission port range of
RTP streaming video. RTP will select a port randomly from the range.
Multicast streaming:
Multicast address: Specify the multicast server address.
Video / Audio Port: Specify the transmission port number of the video data. It is initially
set to 10000 and 11000. Specify an even number from 1024 to 65534.
Time-To-Live: Set the maximum TTL that multicast can pass through.
Image Size: The Image size of Mobile view is fixed at 176x120.
Frame rate:Set the frame rate of the MPEG4 image. Selectable values are 5, 10, 15, 20 fps.
The unit “fps” stands for “frames sent per second”.
16
Quality
Fixed Bitrate:Set the bit rate of MPEG4 image transmission for a line. Selectable values
are 64, 32, and 16kbps..
17
3.2.3 MJPEG
Note:
• MJPEG settings are unavailable if the RTSP mode is ON, which means the MJPEG
streaming is closed.
MJPEG viewer port
Unicast streaming Video/Audio port number : Specify the transmission port number of the
video data. It is initially set to 8070. Specify an even number from 1024 to 65534.
Note:
• Unicast streaming:Specify the transmission port number of the video data and audio
data used when UDP (Unicast) is selected with the TCP/UDP transmission switching
icon in the main viewer.
Image Size:Specify the image size the network camera transmits. You can choose among
704 × 480, 352 × 240 and 176 × 120 for NTSC mode and 704 × 576, 352 × 288 and 176 ×
144 for PAL mode.
Frame rate:Set the frame rate of the MJPEG image. Selectable values are 5, 10, 15 fps. The
unit “fps” stands for “frames sent per second”.
18
Quality
Auto:The quality will be automatically decided.
Fixed quality:The selectable values are Medium, Standard, Good, Detailed and Excellent.
19
3.3 Network
3.3.1 Information
MAC address:Display the MAC address of the device.
Obtain an IP address automatically (DHCP):If a DHCP server is installed on the network, to
select this while the IP address is assigned by the DHCP server.
Note:
• When you set Obtain an IP address automatically (DHCP), make sure that the DHCP
server is working on the network.
Use the following IP address:Select this when a fixed IP address is set.
IP address:Enter the IP address of the device.
Subnet mask:Enter the subnet mask.
Default gateway:Enter the default gateway.
Use the following DNS server address:Select this when you set the fixed address as the IP
address of DNS server.
Primary DNS server:Enter the IP address of the primary DNS server.
Secondary DNS server:Enter the IP address of the secondary DNS server, if necessary.
HTTP port number:Select 80 in general situations. If you want to use a port number other
than 80, select the text box and enter a port number between 1024 and 65535.
Note:
20
• When you have set the HTTP port number to a number other than 80 on the Network
setting page or in the Setup Program, access the device by typing the IP address of the
device on the web browser as follows:
Example: when HTTP port number is set to 2000 Æ http://192.168.1.100:2000/
21
3.3.2 PPPoE
Use this when you connect the device through PPPoE (Point -to- Point Protocol over
Ethernet). PPPoE connection is the protocol that is widely used in xDSL (digital affiliate line
such as ADSL, VDSL or SDSL) as the authentication and connection system.
IP address:The IP address obtained at the PPPoE connecting with network.
User ID:Enter the user ID for authentication necessary for PPPoE connections. Type it up to
64 characters.
Password:Enter the password for authentication necessary for PPPoE connections. Type it
up to 32 characters.
Re-type password:Re-type the password to confirm.
Obtain DNS server address automatically:Select this to obtain the address of DNS server
automatically.
Use the following DNS server address:Select this when you set the fixed address as the IP
address of DNS server.
Primary DNS server:Enter the IP address of the primary DNS server.
Secondary DNS server:Enter the IP address of the secondary DNS server.
22
3.3.3 DDNS
Server name:Choose the DDNS Server from the list.
User ID:Enter the user ID for authentication necessary for DDNS connections. Type it up to
64 characters.
Password:Enter the password for authentication necessary for DDNS connections. Type it
up to 32 characters.
Re-type password:Re-type the password to confirm.
Host name:Enter the host name that is registered to the DDNS server.
Note:
• When you want to use DDNS function, you need to register an account in DDNS server
first.
23
3.3.4 UPnP
The device includes support for UPnP, which is enabled by default. If also enabled on your
computer, the device will automatically be detected and a new icon will be added to “My Network
Places.” It provides port forwarding for opening a port in a router or firewall in a private network in
order to let a party from the outside world contact a user inside.
HTTP port:Enter the HTTP port number and default HTTP port is 80.
SSL port: Enter the SSL port number and default SSL port is 443.
MPEG4 viewer port:Enter the MPEG4 viewer port number and default MPEG4 viewer port is
8090.
MPEG4 viewer port(SSL): Enter the MPEG4 SSL viewer port and default is 8091.
MJPEG viewer port:Enter the MJPEG viewer port number and default MJPEG viewer port is
8070.
MJPEG viewer port(SSL): Enter the MPEG4 SSL viewer port and default is 8071.
MPEG4 RTSP port: Enter the MPEG4 RTSP port, default value is 8050 for computer view,
8030 for mobile view.
24
3.3.5 IP Notification
When network notify type is set to On, you can send an e-mail notification of the completion of the
network setting.
Notify type:Select type of DHCP, Static IP and PPPoE will notify.
SMTP server name:Type the SMTP server name up to 64 characters, or the IP address of
the SMTP server.
Authentication:Select the authentication required when you send an email.
Off: Select if no authentication is necessary when an email is sent.
On: When authentication is necessary an e-mail is sent, select one of the authentication
methods from the followings.
SMTP: Select if SMTP authentication is necessary when an e-mail is sent.
POP before SMTP: Select if POP before SMTP authentication is necessary when an e-mail is
sent.
Note:
• When you set to On, be sure to select either or both SMTP or/and POP before SMTP.
POP server name:It is necessary when the POP before SMTP is selected in Authentication.
Type the POP (receiving mail) server name up to 64 characters, or type the IP address of the
POP server. This setting is necessary when the SMTP server which sends e-mails performs
authentication using the POP user account.
25
User name, Password:Type the user name and Password of the user who has the mail
account. This setting is necessary when the SMTP server which sends e-mails performs
authentication.
Recipient e-mail address:Type the recipient e-Mail address up to 64 characters. You can
specify up to three recipient E-mail addresses.
Administrator e-mail address:Type the Administrator e-Mail address up to 64 characters.
This address is used for reply mail and sending system messages from the SMTP server.
Subject:Type the subject/title of the e-Mail up to 64 characters. With respect to mail which is
sent according to the IP notification.
Message
Type the text of the E-mail up to 384 characters. Default value provides network information
including IP, Port, MAC, Model, Firmware Version and Web Version.
26
3.4 Security
3.4.1 Account
The device default account and password setting is “admin/admin”. That means everyone
might access the device including the configuration as long as the IP address is known. It is
necessary to assign a password if the device is intended to be accessed by others. Use this
menu to set the user names and passwords of Administrator and up to 9 different users (User
1 to User 9), and the access right of each user.
User name:Set a user name between 5 and 16 characters.
Password:Set a password between 5 and 16 characters.
Re-type password:Re-type the password to confirm.
Viewer Mode:Set a user to Admin, Operator or Viewer mode.
Viewer authentication:Allows any viewer direct access to Live View.
27
3.4.2 HTTPS
HTTPS is a URI scheme used to indicate a secure HTTP connection. It is syntactically
identical to the http:// scheme normally used for accessing resources using HTTP. Using an
https: URL indicates that HTTP is to be used, but with a different default TCP port (443) and
an additional encryption/authentication layer between the HTTP and TCP. You can use the IP
camera through HTTPS easily by using https:// instead of http://.
Create & Install: Create a self-signed certificate for HTTPS to recognize.
Installed Certificate: Display or remove the properties of the installed certificate.
HTTPS Connection Policy: Set HTTPS connection policy for different level of users.
28
4. Advance
4.1 FTP Client
Use this menu to set up for capturing and sending images to an FTP server. By using FTP
client function, you can send the image and audio file which has been shot and recorded
linked with the external sensor input or with the built-in motion detection function to FTP server.
FTP client setting menu is composed of two tabs, General, Alarm sending and Periodical
sending.
4.1.1 General
FTP client function:To activate the FTP client function, select On. The FTP client setting
page appears. When you do not wish to use the FTP client function, select Off.
Note:
• The frame rate and operability on the main viewer may decrease while a file is being
transmitted by the FTP client function.
FTP server name:Type the FTP server name to upload still images up to 64 characters, or
the IP address of the FTP server.
User name:Type the user name for the FTP server.
Password:Type the password for the FTP server.
29
Retype password:To confirm the password, type the same characters as you typed in the
Password box.
Passive mode:Set whether you use the passive mode of FTP server or not when connecting
to FTP server. Select On to connect to FTP server using the passive mode.
Attached file type:Set attached file type to MJPEG or MPEG.4
30
4.1.2 Alarm sending
Set to forward the image and audio file to the specified FTP server linked with the alarm
detection by the external sensor input or by the built-in motion detection function. Select On to
send the image and audio file to FTP server linked with the alarm detection.
Remote path:Type the path to the destination in FTP server up to 64 characters.
Image file name:Type the file name you want to assign to the images when sending to the
FTP server. You can use up to 10 alphanumeric characters, - (hyphen) and _ (underscore) for
naming.
Suffix:Select a suffix to add to the file name:
Date & time: The date & time suffix is added to the Image file name. The date/time suffix
consists of lower two-digits of year (2 digits), month (2 digits), date (2 digits), hour (2
digits), minute (2 digits), second (2 digits), and consecutive number (2 digits), thus
14-digit number is added to the file name.
Sequence number: A consecutive number of 10 digits between 0000000001 and
4294967295 and two fixed digits 00 is added to the Image file name.
Motion Detection:Click it on for using Motion Detection function as a sensor. You can set
the motion detection function page.
Note:
• Motion Detection works only when the Video mode is set to MPEG4 and the
Cropping is set to Off.
31
Effective period:Set the period when the periodical sending is effective.
Always:The periodical sending is always effective.
Schedule:You can specify the period when the periodical sending is effective in the
schedule setting in the other section. Click Schedule and the setting menu for the effective
period is displayed.
32
4.1.3 Periodical sending
You can set to send an image file to FTP server periodically by selecting On to send the
image file to FTP server linked with setting period.
Remote path:Type the remote path up to 64 characters.
Image file name:Type the file name of the image sent to FTP server up to 10 alphanumeric
characters, - (hyphen) and _ (under score).
Suffix:Select a suffix to be added to the file name sent to FTP server.
None:The name of the sent file will be the Image file name.
Date & time:The date & time suffix is added to the Image file name. The date & time suffix
consists of lower two-digits of year (2 digits), month (2 digits), date (2 digits), hour (2 digits),
minute (2 digits) and second (2 digits), and consecutive number (2 digits), thus 14-digit
number is added to the file name.
Sequence number:A consecutive number is added to the Image file name.
Sequence number clear:Click Clear and the suffix of the sequence number returns to 1.
Interval:Set the periodical sending is effective interval. Min value is 1 min and Max value is
24 hour.
Effective period:Set the period when the periodical sending is effective.
Always:The periodical sending is always effective.
33
Schedule:You can specify the period when the periodical sending is effective in the
schedule setting in the other section. Click Schedule and the setting menu for the effective
period is displayed. (“Setting the Schedule — Schedule setting Menu” on page 34)
34
4.2 SMTP
Set the SMTP menu when you want to send an image via e-mail. By using Mail (SMTP)
function, you can send a mail with attached image which has been shot linked with the
external sensor input or with the built-in motion detection function. The image file can also be
sent periodically. E-Mail (SMTP) setting menu is composed of three tabs, General, Alarm
sending and Periodical sending.
4.2.1 General
Select On when you use the SMTP function. The common setting options are displayed
below. If you do not wish to use the e-Mail (SMTP) function, select Off and click OK.
Note:
• During transmission of an image file via mail, the frame rate and operation performance
of the monitor image of the main viewer decline.
• While the camera video mode is set to MPEG4, the image of the composite video signal
output from the video output connector of the camera may be distorted during mail
transmission.
• You cannot send an audio file by using the mail sending function.
SMTP server name:Type the SMTP server name up to 64 characters, or the IP address of
the SMTP server.
Authentication:Select the authentication required when you send an email.
35
Off: Select if no authentication is necessary when an email is sent.
On: When authentication is necessary an e-mail is sent, select one of the authentication
methods from the followings.
SMTP: Select if SMTP authentication is necessary when an e-mail is sent.
POP before SMTP: Select if POP before SMTP authentication is necessary when an e-mail is
sent.
Note:
• When you set to On, be sure to select either or both SMTP or/and POP before SMTP.
POP server name : It is necessary when the POP before SMTP is selected in
Authentication. Type the POP (receiving mail) server name up to 64 characters, or type
the IP address of the POP server. This setting is necessary when the SMTP server which
sends e-mails performs authentication using the POP user account.
User name, Password:Type the user name and Password of the user who has the mail
account. This setting is necessary when the SMTP server which sends e-mails performs
authentication.
Recipient e-mail address:Type the recipient e-Mail address up to 64 characters. You
can specify up to three recipient E-mail addresses.
Administrator e-mail address : Type the Administrator e-Mail address up to 64
characters. This address is used for reply mail and sending system messages from the
SMTP server.
Attached File Type: Select to attach the file as JPEG or MPEG4.
Subject:Type the subject/title of the e-Mail up to 64 characters. With respect to mail
which is sent according to the alarm detection when Alarm sending of the alarm tab is
set to On, the characters standing for the sensor type added to the subject.
Message:Type the text of the E-mail up to 384 characters. (A line break is equivalent to
2 characters.)
36
4.2.2 Alarm sending
Set to send the mail with connection to the alarm detection by the external sensor input or
by the built-in motion detection function.
Alarm sending:Select On to set to send mail with connection to the alarm detection.
File attachment:Set whether an image file is attached to the mail sent or not. When On is
selected, the image file made by the settings below is attached. When Off is selected, only the
message is sent.
Image file name:Type the file name you want to assign to the image to attach a mail. You
can use up to 10 alphanumeric, - (hyphen) and _ (underscore) for naming.
Suffix:Select a suffix to add to the file name:
None: No suffix is added. The Image file name is assigned to the image to be sent via an
e-Mail.
Date & time: The date & time suffix is added to the Image file name. The date/time suffix
consists of lower two-digits of year (2 digits), month (2 digits), date (2 digits), hour (2
digits), minute (2 digits), second (2 digits), and consecutive number (2 digits), thus
14-digit number is added to the file name.
Sequence number: A consecutive number of 10 digits between 0000000001 and
4294967295 and two fixed digits 00 is added to the Image file name.
Motion Detection:Click it on for using Motion Detection function as a sensor. You can set
37
the motion detection function page.
Note:
• Motion Detection works only when the Video mode is set to MPEG4 and the
Cropping is set to Off.
38
4.2.3 Periodical sending
You can set to send an image file by SMTP server periodically by selecting On to send the
image file by SMTP server linked with setting period.
Image file name:Type the file name of the image sent by SMTP up to 10 alphanumeric
characters, - (hyphen) and _ (under score).
Suffix:Select a suffix to be added to the file name sent by SMTP.
None:The name of the sent file will be the Image file name.
Date & time:The date & time suffix is added to the Image file name. The date & time suffix
consists of lower two-digits of year (2 digits), month (2 digits), date (2 digits), hour (2 digits),
minute (2 digits) and second (2 digits), and consecutive number (2 digits), thus 14-digit
number is added to the file name.
Sequence number:A consecutive number is added to the Image file name.
Sequence number clear:Click Clear and the suffix of the sequence number returns to 1.
Interval:Set the periodical sending is effective interval. Min value is 30 min and Max value is
24 hour.
Effective period:Set the period when the periodical sending is effective.
Always:The periodical sending is always effective.
Schedule:You can specify the period when the periodical sending is effective in the
schedule setting in the other section. Click Schedule and the setting menu for the effective
period is displayed. (“Setting the Schedule — Schedule setting Menu” on page 34)
39
4.3 HTTP Event
Use this menu to set up for capturing and sending images to an HTTP server. By using
HTTP client function, you can send the image and audio file which has been shot and
recorded linked with the external sensor input or with the built-in motion detection function to
HTTP server. HTTP client setting menu is composed of two tabs, General and Alarm
sending.
4.3.1 General
HTTP event: Set up the HTTP server URL, port, user id, password, and proxy server
settings.
40
4.3.2 Alarm sending
Set to send the mail with connection to the alarm detection by the external sensor input or
by the built-in motion detection function.
Alarm sending:Select On to set to send mail with connection to the alarm detection.
Motion Detection:Click it on for using Motion Detection function as a sensor. You can set
the motion detection function page.
Note:
• Motion Detection works only when the Video mode is set to MPEG4 and the
Cropping is set to Off.
Alarm Buffer:Select Use alarm buffer when you forward the image/ audio of before and
after the alarm detection (pre-alarm, post-alarm). If you do not select it, only the image of the
moment of the alarm detection is forwarded. Click Alarm buffer to display the Alarm buffer
setting menu. For details, see “Setting the Alarm Buffer — Alarm buffer setting Menu on page.
Effective period:Set the period when the periodical sending is effective.
Always:The periodical sending is always effective.
Schedule:You can specify the period when the periodical sending is effective in the
schedule setting in the other section. Click Schedule and the setting menu for the
effective period is displayed.
41
4.4 Schedule
When you click Schedule on the Advanced mode menu, the Schedule setting menu appears.
This is the same menu as the setting menu which is displayed when you click Schedule to set
Effective period and Schedule in FTP client setting menu, e-Mail (SMTP) setting menu, Alarm
out setting menu and so on. Example: When setting e-Mail (SMTP) (the alarm sending) in the
Schedule setting menu.
4.4.1 Setting
Schedule selection
Select the list box to specify the schedule you want to set. e-Mail (SMTP) – Alarm, e-Mail
(SMTP) – Periodical, FTP – Alarm, FTP – Periodical, HTTP event – Alarm, Alarm output –
Alarm or Alarm output – Timer, can be selected.
Mon (Monday) to Sun (Sunday)
The time period on the right of the checked day is the effective period of the schedule.
Start time, End time
Specify the Start time and the End time.
Use the same time schedule every day
When this is checked, the Start time and End time set to Mon (Monday) are applied to all
days. In this case, the Start time and End time of the other days than Mon (Monday)
cannot be input.
42
4.5 Motion Detection
When you click Motion Detection on the Advance mode menu, the Motion Detection
setting menu appears. There are three Motion Detection functions as sensors to set for
different detecting zones. Each one has Threshold and Sensitivity inputs which you can
adjust to specific zone sequentially. Motion Detection function can support to FTP, SMTP
and Alarm output for capturing and sending images or starting alarm output.
Click it On when you use the Motion Detection function and detecting zone appears for
adjusting and moving. The common setting options are displayed below. If you do not wish
to use the Motion Detection function, click it Off and press OK.
Motion Detection 1:Click it on for using Motion Detection 1 function as a sensor. You
can adjust and move the detecting zone by using mouse.
Motion Detection 2:Click it on for using Motion Detection 2 function as a sensor. You
can adjust and move the detecting zone by using mouse.
Motion Detection 3:Click it on for using Motion Detection 3 function as a sensor. You
can adjust and move the detecting zone by using mouse.
Threshold:You can use the tool bar to set up-limit value. When detecting zone signals are
43
over setting value, it would carry on assigned work.
Sensitivity:You can use the tool bar to set down-limit value. When detecting zone signals
are over setting value, it would carry on assigned work.
Carry out the following steps:
1. Click On to Motion Detection 1 choose one of eight orders.
2. A detecting zone 1 appears and use mouse to adjust and move the zone boundaries
and position.
3. Use tool bar to set Threshold and Sensitivity value.
4. Follow the steps to set the other Motion Detection.
5. Click the OK to save the setting.
Note:
• Be careful! Motion Detection function don’t work with Patrol function at same time.
44
4.6 System Log
The System Log function allows users to review any changes and events happened. The
system starts logging automatically after started.
Remote Log: Enables user to send the log data to a specified log server.
45
Atlantis Land
Via Pellizza da Volpedo, 59
20092 Cinisello Balsamo – MI – Italy
info@atlantis-land.com
46
Download PDF

advertising