advertisement
▼
Scroll to page 2
of 82
BARCO PROJECTION SYSTEMS REALITY SIM 6 R9040100 - R9040101 R9040110 - R9040111 OWNER'S MANUAL Date : 21032000 Rev. : 00 Art. No. : R5976135 Federal communication commission (FCC statement) This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Instructions to the user : if this equipment does cause interference to radio or television reception, the user may try to correct the interference by one or more of the following measures : Re-orientation of the receiving antenna for the radio or television. Relocate the equipment with respect to the receiver. Plug the equipment into a different outlet so that the equipment and receiver are on different branch circuits. Fasten cables connectors to the equipment by mounting screws. Note : The use of shielded cables is required to comply within the limits of Part15 of FCC rules and EN55022. Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, March 2000. All rights reserved. Trademarks are the rights of their respective owners. BARCO n.v./Projection Systems Noordlaan 5 B-8520 Kuurne Belgium Tel : +32/56/368211 Fax : +32/56/351651 E-mail : [email protected] Visite Barco at the web : http://www.barco.com Printed in Belgium Table of Contents 1 TABLE OF CONTENTS TABLE OF CONTENTS ...................................................................................................... 1-1 PACKAGING AND DIMENSIONS ...................................................................................... 2-1 Projector Packaging ..................................................................................................................................... 2-1 Way of Packaging ......................................................................................................................................... 2-1 To unpack ...................................................................................................................................................... 2-1 Hint ............................................................................................................................................................... 2-1 Contents of the complete unit (box) : ........................................................................................................... 2-1 Lens Packaging ............................................................................................................................................ 2-1 Way of Packaging ......................................................................................................................................... 2-1 Projector Case .............................................................................................................................................. 2-2 Dimensions ................................................................................................................................................... 2-2 INSTALLATION GUIDELINES ........................................................................................... 3-1 Safety warning .............................................................................................................................................. 3-1 Installation Guidelines .................................................................................................................................. 3-1 Ambient Temperature Conditions ................................................................................................................. 3-1 Environment .................................................................................................................................................. 3-1 What about ambient light ? ........................................................................................................................... 3-1 Which screen type? ...................................................................................................................................... 3-1 What image size? How big should the image be? ...................................................................................... 3-1 Projector Configurations ............................................................................................................................... 3-2 Which configuration can be used ? .............................................................................................................. 3-2 Positioning the Projector ............................................................................................................................... 3-2 Lenses .......................................................................................................................................................... 3-3 Which lens has to be selected. ..................................................................................................................... 3-3 Available lenses ............................................................................................................................................ 3-3 Lens formulas to calculate the projector distance. ....................................................................................... 3-4 How to install the lens?................................................................................................................................. 3-4 Cleaning the Lens ......................................................................................................................................... 3-5 Battery installation in the RCU. .................................................................................................................... 3-5 Inserting the Batteries. .................................................................................................................................. 3-5 How to replace the batteries in the RCU ? ................................................................................................... 3-5 Note .............................................................................................................................................................. 3-6 CONNECTIONS .................................................................................................................. 4-1 Power connection to Projector ..................................................................................................................... 4-1 AC Power (mains) cord connection .............................................................................................................. 4-1 Fuses ............................................................................................................................................................ 4-1 Switching on ................................................................................................................................................. 4-1 Lamp Run Time ............................................................................................................................................ 4-2 Lamp Run Time Warning .............................................................................................................................. 4-2 Switching to Stand-by. .................................................................................................................................. 4-2 Switching Off................................................................................................................................................. 4-3 Switching to Stand-by Warning .................................................................................................................... 4-3 Input Source Connection .............................................................................................................................. 4-3 Input facilities ..................................................................................................................................................... Input Selection .............................................................................................................................................. 4-3 Input Facilities, RCVDS05 connected. ......................................................................................................... 4-3 5-cable Input Slot (slot 1) ............................................................................................................................. 4-4 Computer input/Monitor output² .................................................................................................................... 4-5 5976135 BARCOREALITY SIM6 21032000 i-1 Table of Contents Video Input (Optional) ................................................................................................................................... 4-6 S-Video Input (optional) ................................................................................................................................ 4-6 Serial Digital Input / Serial Digital Output (optional) ..................................................................................... 4-7 IEEE 1394 Input ........................................................................................................................................... 4-7 RS232 Connection ........................................................................................................................................ 4-8 RS232 in / RS232 out ................................................................................................................................... 4-8 Applications : ................................................................................................................................................ 4-8 Set up of the Baud Rate for Communication with a Computer : ................................................................. 4-8 Communication port for communication with peripherals ............................................................................ 4-8 Configurations of the port. ............................................................................................................................ 4-8 Connecting a RCVDS 05 to the projector. .................................................................................................... 4-8 TRIG Output ................................................................................................................................................. 4-8 MOUSE ......................................................................................................................................................... 4-9 When available ? .......................................................................................................................................... 4-9 How to activate ? .......................................................................................................................................... 4-9 Available Mouse Functions ........................................................................................................................... 4-9 Audio Connections (optional) ....................................................................................................................... 4-9 What is available ? ....................................................................................................................................... 4-9 How to lock an audio input ? ........................................................................................................................ 4-9 GETTING STARTED ........................................................................................................... 5-1 Remote Control & Local Keypad .................................................................................................................. 5-1 How controlling the projector ? ..................................................................................................................... 5-1 Location of the local keypad ......................................................................................................................... 5-1 Remote control ............................................................................................................................................. 5-1 Overview of Terminology .............................................................................................................................. 5-1 Operating the Projector ................................................................................................................................ 5-2 Switching on ................................................................................................................................................. 5-2 Lamp Run Time ............................................................................................................................................ 5-3 Lamp Run Time Warning .............................................................................................................................. 5-3 Switching to Stand-by. .................................................................................................................................. 5-3 Switching Off ................................................................................................................................................. 5-3 Switching to Stand-by Warning .................................................................................................................... 5-3 Quick Set Up Adjustments ........................................................................................................................... 5-3 Quick Lens Adjustment ................................................................................................................................. 5-3 Quick On Screen Color change .................................................................................................................... 5-4 Using the RCU .............................................................................................................................................. 5-5 Pointing to the reflective screen ................................................................................................................... 5-5 Hardwired Remote Input. .............................................................................................................................. 5-5 Directly to one of the IR sensors of the projector. ........................................................................................ 5-5 Projector address .......................................................................................................................................... 5-6 Why a projector address ? ............................................................................................................................ 5-6 Set up an Individual Projector Address. ....................................................................................................... 5-6 How to control the projector or projectors. ................................................................................................... 5-6 Before using the RCU. .................................................................................................................................. 5-6 Common Address ......................................................................................................................................... 5-6 Displaying the Projector Address on the Screen. ......................................................................................... 5-6 How to Program an Address into the RCU? ................................................................................................. 5-6 Sound Controls (optional). ............................................................................................................................ 5-7 Controlling the Projector ............................................................................................................................... 5-7 Input Selection .............................................................................................................................................. 5-7 Picture controls. ............................................................................................................................................ 5-7 The Pause key. ............................................................................................................................................. 5-8 The Selection key. ........................................................................................................................................ 5-8 START UP OF THE ADJUSTMENT MODE ....................................................................... 6-1 Adjustment Mode .......................................................................................................................................... 6-1 Start Up ......................................................................................................................................................... 6-1 Possible Paths .............................................................................................................................................. 6-1 i-2 5976135 BARCOREALITY SIM6 21032000 Table of Contents Password Protection ..................................................................................................................................... 6-1 Entering the Password ................................................................................................................................. 6-1 Remark ......................................................................................................................................................... 6-2 Setting up your own password ..................................................................................................................... 6-2 RANDOM ACCESS ADJUSTMENT MODE ....................................................................... 7-1 Random Access Mode .................................................................................................................................. 7-1 Possible File Manipulations. ......................................................................................................................... 7-2 File Annotation. ............................................................................................................................................. 7-2 Starting Up .................................................................................................................................................... 7-2 Picture Service ............................................................................................................................................. 7-2 Connecting a new Source. ........................................................................................................................... 7-2 Start up the File Service. .............................................................................................................................. 7-2 Load File ...................................................................................................................................................... 7-3 How to load a file ? ....................................................................................................................................... 7-3 The image is not perfect ? ............................................................................................................................ 7-3 Edit File ........................................................................................................................................................ 7-3 What can be done with the Edit File menu ? ................................................................................................ 7-3 How to start up the Edit menu ? ................................................................................................................... 7-4 Which items can be adjusted ? ..................................................................................................................... 7-4 How to change the settings ? ....................................................................................................................... 7-4 How to find the correct values for the displayed item? ................................................................................ 7-4 Rename a file ............................................................................................................................................... 7-6 Start Up ......................................................................................................................................................... 7-6 How to change the characters ? ................................................................................................................... 7-7 Copy a file .................................................................................................................................................... 7-7 Start Up ......................................................................................................................................................... 7-7 How to change the characters ? ................................................................................................................... 7-7 Delete .......................................................................................................................................................... 7-8 Start Up ......................................................................................................................................................... 7-8 File Options .................................................................................................................................................. 7-8 Start Up ......................................................................................................................................................... 7-8 File Sort ........................................................................................................................................................ 7-8 Picture Tuning ............................................................................................................................................... 7-9 Start Up ......................................................................................................................................................... 7-9 Which items are available ? .......................................................................................................................... 7-9 CTI ON/OFF ................................................................................................................................................ 7-9 What is CTI ? ................................................................................................................................................ 7-9 How to change thet CTI settings .................................................................................................................. 7-9 Note : ............................................................................................................................................................ 7-9 Motion Compensation .................................................................................................................................. 7-9 What is motion compensation ? ................................................................................................................... 7-9 LCD speed .................................................................................................................................................. 7-10 LCD speed R/G .......................................................................................................................................... 7-10 LCD speed B/G........................................................................................................................................... 7-10 How to start up ? ........................................................................................................................................ 7-10 Color Temperature ..................................................................................................................................... 7-11 Start Up ....................................................................................................................................................... 7-11 Available Color Temperature : .................................................................................................................... 7-11 Adjusting the Color Temperature ................................................................................................................ 7-11 Gamma ...................................................................................................................................................... 7-12 What can be adjusted ? .............................................................................................................................. 7-12 How to change the gamma value ? ............................................................................................................ 7-12 Decoding EBU/IRE .................................................................................................................................... 7-12 Note : .......................................................................................................................................................... 7-12 What can be done ? .................................................................................................................................... 7-12 How can it be selected ? ............................................................................................................................ 7-12 Color Depth ................................................................................................................................................ 7-12 Purpose....................................................................................................................................................... 7-12 5976135 BARCOREALITY SIM6 21032000 i-3 Table of Contents Input Balance ............................................................................................................................................. 7-13 Why adjusting the input balance ? .............................................................................................................. 7-13 How to adjust the input balance ? .............................................................................................................. 7-13 To change the Color depth value : .............................................................................................................. 7-13 Black Color ................................................................................................................................................ 7-13 Purpose ....................................................................................................................................................... 7-13 To change the black color : ......................................................................................................................... 7-13 Audio Tuning ............................................................................................................................................... 7-14 Start Up ....................................................................................................................................................... 7-14 Available items ............................................................................................................................................ 7-14 Volume, Balance, Bass and Treble ........................................................................................................... 7-14 How to adjust ? ........................................................................................................................................... 7-14 Fade ........................................................................................................................................................... 7-15 Purpose ....................................................................................................................................................... 7-15 How to set up the fade ? ............................................................................................................................. 7-15 Mute ........................................................................................................................................................... 7-15 Purpose ....................................................................................................................................................... 7-15 How to stop sound reproduction ? .............................................................................................................. 7-15 Mode [stereo]/[mono] ................................................................................................................................. 7-15 Purpose ....................................................................................................................................................... 7-15 How to install the sound mode ? ................................................................................................................ 7-15 Video - Audio lock ...................................................................................................................................... 7-16 Purpose ....................................................................................................................................................... 7-16 How to lock input source to an audio source ? ........................................................................................... 7-16 Geometry .................................................................................................................................................... 7-16 To start up the Geometry functions ............................................................................................................ 7-16 Which Geometry adjustments are possible ? ............................................................................................. 7-16 How can an adjustment be adjusted ? ....................................................................................................... 7-16 Shift ............................................................................................................................................................ 7-17 What can be done ? .................................................................................................................................... 7-17 To start up the shift action : ........................................................................................................................ 7-17 Size ............................................................................................................................................................ 7-17 What can be done ? .................................................................................................................................... 7-17 To start up the size adjustment : ................................................................................................................. 7-17 Side Keystone ............................................................................................................................................ 7-18 What can be done ? .................................................................................................................................... 7-18 Aligning the keystone ................................................................................................................................. 7-18 Blanking ..................................................................................................................................................... 7-18 What can be done ? .................................................................................................................................... 7-18 Available Blanking Adjustments ................................................................................................................. 7-18 Adjusting the blanking. ............................................................................................................................... 7-19 Aspect Ratio [5:4]/[4:3]/[16:9] .................................................................................................................... 7-19 Purpose ....................................................................................................................................................... 7-19 How to setup the desired aspect ratio ? ..................................................................................................... 7-19 Options ...................................................................................................................................................... 7-20 How to change the geometry options ? ...................................................................................................... 7-20 Soft Edge .................................................................................................................................................... 7-20 To start up the Soft Edge function .............................................................................................................. 7-20 Which soft edge items are available ? ........................................................................................................ 7-20 Type ........................................................................................................................................................... 7-20 Purpose ....................................................................................................................................................... 7-20 How selecting the soft edge area ? ............................................................................................................ 7-20 Available soft edge types. ........................................................................................................................... 7-21 Demo .......................................................................................................................................................... 7-21 Purpose ....................................................................................................................................................... 7-21 Available image processing features .......................................................................................................... 7-21 How to start up the Demo ? ........................................................................................................................ 7-21 Size ............................................................................................................................................................ 7-21 Purpose ....................................................................................................................................................... 7-21 How to set up the width ? ........................................................................................................................... 7-21 i-4 5976135 BARCOREALITY SIM6 21032000 Table of Contents Split Screen ............................................................................................................................................... 7-22 Purpose....................................................................................................................................................... 7-22 How to start up ? ........................................................................................................................................ 7-22 INSTALLATION MODE ....................................................................................................... 8-1 Installation Mode .......................................................................................................................................... 8-1 Start Up ......................................................................................................................................................... 8-1 Input Slots ..................................................................................................................................................... 8-1 What can be done ? ...................................................................................................................................... 8-1 To view or to change the input configuration : .............................................................................................. 8-1 Possible results for the input slots : .............................................................................................................. 8-2 What if a switcher is connected to the projector ? ........................................................................................ 8-2 800 Peripheral .............................................................................................................................................. 8-2 Defining the Output module of the RCVDS05 .............................................................................................. 8-2 Defining the Infrared Communication protocol ............................................................................................. 8-2 Configuration ................................................................................................................................................ 8-3 What can be done ? ...................................................................................................................................... 8-3 Set up the Correct Configuration .................................................................................................................. 8-3 OSD color (On-Screen Display) ................................................................................................................... 8-3 What can be done ? ...................................................................................................................................... 8-3 How to change this color setting ? ............................................................................................................... 8-3 Internal Patterns ........................................................................................................................................... 8-3 What can be done with these internal patterns ? ......................................................................................... 8-3 How to select an internal pattern ? ............................................................................................................... 8-4 Available patterns ......................................................................................................................................... 8-4 No Signal ...................................................................................................................................................... 8-4 What will happen ? ....................................................................................................................................... 8-4 Changing the background color .................................................................................................................... 8-4 Changing the shutdown setting .................................................................................................................... 8-4 Quick Access Keys ....................................................................................................................................... 8-5 What can be done ? ...................................................................................................................................... 8-5 Getting an overview ...................................................................................................................................... 8-5 Factory preprogrammed keys ....................................................................................................................... 8-5 How to program the quick access keys (function keys) : ............................................................................. 8-5 Lens Adjustments ......................................................................................................................................... 8-6 What can be done ? ...................................................................................................................................... 8-6 Zoom/Focus/Shift.......................................................................................................................................... 8-6 Menu Position ............................................................................................................................................... 8-7 What can be done ? ...................................................................................................................................... 8-7 How to change the setting ? ......................................................................................................................... 8-7 SERVICE MODE ................................................................................................................. 9-1 Service Mode ................................................................................................................................................ 9-1 Start Up ......................................................................................................................................................... 9-1 Built-up of the service mode. ........................................................................................................................ 9-1 Identification .................................................................................................................................................. 9-2 What can be seen ? ...................................................................................................................................... 9-2 Start Up ......................................................................................................................................................... 9-2 Available items .............................................................................................................................................. 9-2 Title Page ..................................................................................................................................................... 9-2 What will be indicated on the title page ? ..................................................................................................... 9-2 Start Up ......................................................................................................................................................... 9-3 Available items .............................................................................................................................................. 9-3 SIM Options ................................................................................................................................................. 9-3 What will be indicate ? .................................................................................................................................. 9-3 Start Up ......................................................................................................................................................... 9-3 Change Projector Address ........................................................................................................................... 9-4 What can be changed ? ................................................................................................................................ 9-4 Change Password ........................................................................................................................................ 9-4 5976135 BARCOREALITY SIM6 21032000 i-5 Table of Contents How to enable or disable the password function ? ....................................................................................... 9-4 How to change the password ? .................................................................................................................... 9-4 Change Language ........................................................................................................................................ 9-4 Start Up ......................................................................................................................................................... 9-4 Start up ......................................................................................................................................................... 9-5 Projector Address ........................................................................................................................................ 9-5 How to change that address ? ...................................................................................................................... 9-5 Entering the new projector address .............................................................................................................. 9-5 Common Address ........................................................................................................................................ 9-5 How to change that common address ? ....................................................................................................... 9-5 Entering the new common address .............................................................................................................. 9-5 Change Baudrate PC ................................................................................................................................... 9-6 Start Up ......................................................................................................................................................... 9-6 Reset Lamp Runtime .................................................................................................................................... 9-6 When is it allowed ? ...................................................................................................................................... 9-6 Lamp Run Time History ................................................................................................................................ 9-6 What can be done ? ...................................................................................................................................... 9-6 Start Up ......................................................................................................................................................... 9-7 Dimming ........................................................................................................................................................ 9-7 What can be done ? ...................................................................................................................................... 9-7 Start Up ......................................................................................................................................................... 9-7 Lamp Dimming ............................................................................................................................................. 9-7 Start Up ......................................................................................................................................................... 9-7 Motorized Dimming ...................................................................................................................................... 9-8 Start Up ......................................................................................................................................................... 9-8 BARCO logo ................................................................................................................................................ 9-8 What can be done ? ...................................................................................................................................... 9-8 How to add the BARCO logo or to change a setting ? ................................................................................. 9-8 Available settings .......................................................................................................................................... 9-8 Panel Adjustments ........................................................................................................................................ 9-9 Warning ......................................................................................................................................................... 9-9 Start Up ......................................................................................................................................................... 9-9 Uniformity ...................................................................................................................................................... 9-9 Warning ......................................................................................................................................................... 9-9 Preset Input Balance .................................................................................................................................. 9-10 Warning ....................................................................................................................................................... 9-10 Start Up ....................................................................................................................................................... 9-10 I2C diagnosis. ............................................................................................................................................. 9-10 What can be done ? .................................................................................................................................... 9-10 STANDARD SOURCE SET UP FILES .............................................................................. A-1 SOURCE NUMBERS 81 - 86 AND 91 - 96 ....................................................................... B-1 Projector without any 800 peripheral connected. ........................................................................................ Projector with a 800 peripheral connected. ................................................................................................. Source numbers 91 - 99. ............................................................................................................................. Source numbers 81 - 86 .............................................................................................................................. i-6 B-1 B-1 B-1 B-2 5976135 BARCOREALITY SIM6 21032000 Packaging and Dimensions 1 PACKAGING AND DIMENSIONS Projector Packaging Way of Packaging The projector is packed in a carton box. To provide protection during transportation, the projector is surrounded with foam. the package is the secured with banding and fastening clips. To unpack First release the fastening clips and remove the banding. Handle as shown in the drawing. Pull To open Take the projector out of its shipping carton and place it on a table. 1 2 3 4 5 37 9 Hint Save the original shipping carton and packing material, they will be necessary if you ever have to ship your projector. For maximum protection, repack your projector as it was originally packed at the factory. Contents of the complete unit (box) : - 1 BARCOREALITY SIM 6 (weight ± 17 kg or ± 37.4 lbs) 1 remote control unit RCU + 2 batteries. 1 power cable with outlet plug type CEE7 or ANSI 73.11 . 1 owner’s manual 1 safety manual Lens Packaging Way of Packaging Lenses are supplied as an individual item. They are packed in a carton. 5976135 BARCOSIM 6 21032000 1-1 Packaging and Dimensions Projector Case Dimensions The dimensions are given in mm. 25.4 mm = 1" 82.7 211.4 169.5 139.6 14 43 60 42 124.1 124.4 147.8 217.2 46 148.9 380.6 368.7 184.4 526.8 371.2 202.4 53.5 53.5 29.6 1-2 min 12 max 24 97.6 107.5 245.1 120.2 187.2 6 152.6 152.6 5976135 BARCOSIM 6 21032000 Installation Guidelines 2 INSTALLATION GUIDELINES Safety warning Before installing the projector, read first the safety instructions Installation Guidelines Ambient Temperature Conditions Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to the optimum use of the projection system. Max. ambient temperature : 40 °C or 104 °F Min. ambient temperature : 0 °C or 32 °F The projector will not operate if ambient air temperature falls outside this range (0°C- 40°C or 32°F-104°F). Environment Do not install the projection system in a site near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust or humidity. Be aware that room heat rises to the ceiling; check that temperature near the installation site is not excessive. What about ambient light ? The ambient light level of any room is made up of direct or indirect sunlight and the light fixtures in the room. The amount of ambient light will determine how bright the image will appear. So, avoid direct light on the screen. Windows that face the screen should be covered by opaque drapery while the set is being viewed. It is desirable to install the projection system in a room whose walls and floor are of non-reflecting material. The use of recessed ceiling lights and a method of dimming those lights to an acceptable level is also important. Too much ambient light will ‘wash out’ of the projected image. This appears as less contrast between the darkest and lightest parts of the image. With bigger screens, the ‘wash out’ becomes more important. As a general rule, darken the room to the point where there is just sufficient light to read or write comfortably. Spot lighting is desirable for illuminating small areas so that interference with the screen is minimal. Which screen type? There are two major categories of screens used for projection equipment. Those used for front projected images and those for rear projection applications. Screens are rated by how much light they reflect (or transmit in the case of rear projection systems) given a determined amount of light projected toward them. The ‘GAIN’ of a screen is the term used. Front and rear screens are both rated in terms of gain. The gain of screens range from a white matte screen with a gain of 1 (x1) to a brushed aluminized screen with a gain of 10 (x10) or more. The choice between higher and lower gain screens is largely a matter of personal preference and another consideration called the Viewing angle. In considering the type of screen to choose, determine where the viewers will be located and go for the highest gain screen possible. A high gain screen will provide a brighter picture but reduce the viewing angle. For more information about screens, contact your local screen supplier. What image size? How big should the image be? The projector is designed for projecting an image size (video) from 1.00m (3.3ft) to 6.00m (19.7ft) with a aspect ratio of 5 to 4. 5976135 BARCOSIM 6 21032000 2-1 Installation Guidelines Projector Configurations Which configuration can be used ? The projector can be installed to project images in four different configurations : Front/table Rear/table Front/ceiling or Rear/ceiling 5HDU&HLOLQJ )URQW&HLOLQJ 5HDU7DEOH )URQW7DEOH Positioning the Projector Drawing are given for a nominal lens position. Definitions of the Abbreviation on drawings B = Distance between ceiling and top of the screen or between floor and bottom of the screen. A = Correction value, distance between bottom side of projector (without feet) and middle of the lens. Value to be subtracted from B to obtain the correct installation position. (A value is a constant value for all screen widths and type of lenses, A = 124.1 mm or 4.89 inch) CD = Total distance between projector and ceiling or projector and floor. SW = Screen width. SH = Screen height (image height). PD = Projector Distance, distance between screen and projector. 2-2 5976135 BARCOSIM 6 21032000 Installation Guidelines OFF-Axis installation ON-Axis installation CD = B - A Projector SIDE VIEW SIDE VIEW SH CD = B - A Screen SH Projector Screen Optical axis projection lens A’ PD Optical axis projection lens A PD B B CD CD Floor Floor SW SW Screen Screen TOP VIEW TOP VIEW SW SW SH SH Floor BACK VIEW Floor BACK VIEW Lenses Which lens has to be selected. 1 Determine the required screen width. 2 Determine the approximate position of the projector in the projection room with regard to the screen and measure the projector-screen distance (PD). 3 Use the lens formulas in appendix B to find the best corresponding PD with regard to the measured projector-screen distance for the required screen width. The desired lens is determined. Available lenses The projector is supplied without any lens. The following lenses are available, or will become available (contact a Barco service center) as an option : Lenses Standard version Scheimpflug version QGD(1.36-2.06:1) QGD(7:1) QGD(0.8:1) On-Axis lens for screen sizes from 40-70 inch diagonal QGD(0.8:1) On-Axis lens for screen sizes from 84-120 inch diagonal QGD(1.27:1) QGD(2-2.8:1) QFD(1.27:1) QFD(1.4-2:1) QFD(2.1-3:1) QFD(2.5:1) QFD(4.5-6:1) R9829850 R9840030 R9829800 R9840520 R9840480 R9840040 R9840490 R9840000 R9829790 R9840400 R9840380 R9840390 R9840290 R9840100 R9840500 5976135 BARCOSIM 6 21032000 R9840600 R9840610 R9840470 R9840460 2-3 Installation Guidelines Lens formulas to calculate the projector distance. Metric formulas (meter) Inch formulas (inch) QGD(1.36-2:1) PDmin=1.371 x SW + 0.165 + 0.0083/SW PDmax=2.086 x SW + 0.153 - 0.015/SW PDmin=1.371 x SW + 6.5 + 12.86/SW PDmax=2.086 x SW + 6.02 - 23.25/SW QGD(7:1) PD = 7.021 x SW + 0.047 + 0.0093/SW PD = 7.021 x SW + 1.85 + 14.41/SW QGD(0.8:1) PD = 0.794 x SW - 0.048 + 0.0072/SW PD = 0.794 x SW - 1.89 + 11.16/SW QDG(1.27:1) PD = 1.356 x SW - 0.065 + 0.0297/SW PD = 1.356 x SW - 2.56 + 46.03/SW QGD(2-2.8) PDmin = 1.982 x SW + 0.476 - 0.388/SW PDmax = 2.778 x SW + 0.068 - 0.015/SW PDmin = 1.982 x SW + 18.74 - 601.4/SW PDmax = 2.778 x SW + 2.68 - 23.25/SW QFD(1.27:1) PD = 1.33 x SW - 0.0195 + 0.0270/SW PD = 1.33 x SW - 0.77 + 41.85/SW QFD(1.4-2:1) PDmin= 1.48 x SW - 0.0287 - 0.0215/SW PDmax= 2.25 x SW - 0.01 + 0.0195/SW PDmin= 1.48 x SW - 1.30 - 33.32/SW PDmax= 2.25 x SW - 0.39 + 30.22/SW QFD(2.1-3:1) PDmin= 2.18 x SW - 0.1 + 0.055/SW PDmax= 2.97 x SW + 0.1 - 0.073/SW PDmin= 1.48 x SW - 3.94 + 85.25/SW PDmax= 2.25 x SW + 3.94 - 113.15/SW QFD (2.5:1) PD = 2.486 x SW + 0.025 + 0.0215/SW PD = 2.486 x SW + 0.98 + 33.32/SW QFD(4.5-6:1) PDmin= 4.39 x SW - 0.02 - 0.029/SW PDmax= 6.00 x SW + 0.15 - 0.107/SW PDmin= 4.39 x SW - 0.79 - 44.95/SW PDmax= 6.00 x SW + 5.91 - 185.65/SW Lens program to calculate the projector distance is available on the BARCO webside : http://www.barco.com/projecti/cusserv/index.htm Remark : In case of the Scheimpflug version lens, the formulas are valid in the normal position. How to install the lens? Installation of the lens for a standard SIM projector. The installation of the scheimphlug lens is described in the corresponding lens kit. 1. 2. 3. 4. 5. 6. 7. 8. Take the lens out of its packing material. Open the lens cover of the projector by pivoting it up and take it off. image 1 Loosen the fixing screws (B) of the motor part (A) and flip the motor part up. image 2 Open both lens locks (C) by pulling them backwards (first, lift up a little before pulling backwards). image 2 Put the lens on the lens holder. Fix the lens by closing the both locks (C) until they are secured. image 3 Flip the motor part back (A) (if a motorized lens is installed, be sure the teeth match the tooth profile (D) of the lens) and secure with the fixing screws (B). image 3 Re-install the lens cover. image 4 Image 1 Image 2 2-4 5976135 BARCOSIM 6 21032000 Installation Guidelines Image 3 Image 4 Cleaning the Lens To minimize the possibility of damaging the optical coating or scratching exposed lens surface, we have developed recommendations for cleaning the lens. FIRST, we recommend you try to remove any material from the lens by blowing it off with clean, dry deionized air. DO NOT use any liquid to clean the lenses. A TorayseeTM cloth is included with the lens kit. Proceed as follows : 1. Always wipe lenses with a CLEAN TorayseeTM cloth. 2. Always wipe lenses in a single direction. Do not wipe back and forwards across the lens surface as this tends to grind dirt into the coating. 3. Do not leave cleaning cloth in either an open room or lab coat pocket, as doing so can contaminate the cloth. 4. If smears occur when cleaning lenses, replace the cloth. Smears are the first indication of a dirty cloth. 5. Do not use fabric softener when washing the cleaning cloth or softener sheets when drying the cloth. 6. Do not use liquid cleaners on the cloth as doing so will contaminate the cloth. Order number for a new TorayseeTM cloth : R379058. Other lenses can also be cleaned safely with this TorayseeTM cloth. Battery installation in the RCU. Inserting the Batteries. Two batteries are packed together with the RCU. Before using your RCU, install first these batteries. 1 2 3 4 Remove the battery cover on the backside by pushing the handle a little towards the bottom of the RCU. Lift up the top side of the cover at the same time. Insert the batteries as indicated in the RCU. Put the battery cover on its place. How to replace the batteries in the RCU ? To replace the batteries : 1 2 3 4 5 6 7 Remove the battery cover on the backside by pushing the handle a little towards the bottom of the RCU. Lift up the top side of the cover at the same time. Push on the + side of the battery towards the - side Lift up the battery at the same time. Repeat for the second battery. Insert the batteries as indicated in the RCU (battery type AA or LR6 or equivalent). Put the battery cover on its place. 5976135 BARCOSIM 6 21032000 2-5 Installation Guidelines Note Note, only important if more than one projector is installed in the room : 1. the common address can be zero (0) or one (1). The standard RCU are setup for common address zero. To change the common address of the RCU, contact a BARCO service center. If it is necessary to program the projector address into the RCU, see chapter 'Controlling'. 2. projector address has to be reprogrammed everytime the battery is changed, the RCU will always switch to the default address. 2-6 5976135 BARCOSIM 6 21032000 Connections 4 CONNECTIONS Power connection to Projector AC Power (mains) cord connection Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector at the front of the projector. The power input is auto-ranging from 90 to 240 VAC. RC TRIG R G B H/C V 1 C OMPUTER M OUSE RS2 32 IN RS23 2 O UT C OMM. PO RT 2 100-240 V 6-2.5 A 50-60 Hz Fuses Warning For continued protection against fire hazard : - refer replacement to qualified service personnel - ask to replace with the same type of fuse. Fuse type : T10 AH/250V Switching on Use the power switch to switch on. When '0' is visible, the projector is switched off. When '1' is visible, the projector is switched on. When switching on with the power switch, the projector starts in the stand by mode. The projector mode indication lamp is red. 5976135 BARCOSIM 6 21032000 4-1 Connections To start image projection : a. press the 'Stand by' button once on the local keypad or on the remote control. The projector mode indication lamp will be green. b. press a digit button to select an input source. The projector mode indication lamp will be green. ) ) 6WDQGE\NH\ ) ) ) $'- (;,7 3URMHFWRUPRGHLQGLFDWLRQ (17(5 EXIT STANDBY TEXT SHARPN PHASE 3$86( 7(;7 3+$6( ENTER PAUSE TINT BRIGHTN 7,17 COLOR &2175$67 &2/25 %5,*+71 &2175 6+$531 75(%/( %$/$1&( %$66 92/ Lamp Run Time When the total run time of the lamp is X-30 hours or more, the following warning message will be displayed for 1 minute. This warning message will be repeated every 30 minutes. Press EXIT to remove the message before the minute is over. Remaining Lamp run time 20 h When the total run time of the lamp is X hours or more, the following warning message, with the exact run time is displayed on the screen. WARNING Lamp run time is X hours Operating the lamp longer than X hours may damage the projector. Please replace the lamp <ENTER> to continue Lamp run time is X hours. Operating the lamp longer than X hours may damage the projector. Please replace the lamp. When OK (ENTER) is pressed to go on, the warning will be repeated every 30 min. The total lifetime of the lamp for a safe operation is X hours max. Do not use it longer. Always replace with a same type of lamp. Call a BARCO authorized service technician for lamp replacement. Lamp Run Time Warning Using a lamp for more than X hours is dangerous as the lamp could explode. Switching to Stand-by. When the projector is running and you want to go to stand-by, press the stand-by key for 2 seconds until the message 'Saving data, please wait' is displayed. Do not press any longer on the standby key otherwise the projector will restart. Saving data, Please wait 4-2 5976135 BARCOSIM 6 21032000 Connections Switching Off To switch off: - First press STANDBY key for 2 seconds. When the message 'Saving data, please wait' is displayed, do not press any longer on the standby key otherwise the projector will restart. Let cool down the projector at least 10 min. - Switch off the projector with the power switch. Switching to Stand-by Warning When switching to standby, it is possible to restart within the first 5sec.. When not restarted within these first 5 sec., the projector waits for 1 min. to restart again. During this period the LED display will show a jumping square with a dash. After one minute, two dashes will be displayed and the projector can restart. Input Source Connection Input facilities For a standard SIM6: 5-cable input Computer Optional inputs: Video S-Video Serial digital input IEEE 1394 (not yet active) Input Selection This can be manually or automatically. When 'automatic' is selected in the Input slots menu, by starting up the projector, it searches for an input source by scanning the inputs one by one. If only one source is found, this source will be projected. If different sources are found, the priority is as follow (for a SIM6 with all input option) : 1. Video 2. S-Video 3. 5 Cable input 4. Computer input SDI input and IEEE input are never automatically selected. Note : When a RCVDS is connected to the projector, the 'Automatic' selection is disabled. Set up of the input selection 1 2 3 4 5 6 7 8 Press Press Press Press Press Press Press Press ENTER to start up the adjustment mode. the cursor key é or ê to select 'Installation' (menu 1). ENTER to display the Installation menu. the cursor key é or ê to select 'Input Slots' (menu 2). ENTER to display the Input slots menu. the cursor key é or ê to select 'Input Slots' (menu 3). ENTER to toggle between [Manual] or [Automatic]. EXIT several times to leave the adjustment mode. ADJUSTMENT MODE INSTALLATION Select a path from below : INPUT SLOTS RANDOM ACCESS INSTALLATION Select with ê or é then <ENTER> <EXIT> to return. Select with ê or é then <ENTER> <EXIT> to return. menu 1 menu 2 INPUT SLOTS SLOT SELECTOR [Automatic] x - 1. 2. 3. 4. 5. 6. RGB [HS&VS] RGB [HS&VS] VIDEO S-VIDEO DIGITAL INPUT IEEE 1394 Select with ê or é <ENTER> to toggle <EXIT> to return. menu 3 Input Facilities, RCVDS05 connected. When using a RCVDS05, it is recommended to use a 5-cable output module in the RCVDS. The outputs of this module have to be connected to the 5 cable input (slot 1) of the projector. To switch the projector in the 5-cable mode see chapter 'Installation mode'. 5976135 BARCOSIM 6 21032000 4-3 Connections 5-cable Input Slot (slot 1) Slot 1 has 5 BNC input terminals. 3 VIDEO R G S-VIDEO B 4 S DI H/C 5 SDO V IEE E 1394 C OM PUTER 1 6 TRIG 2 MONITOR M Which signals can be connected to the 5-cable input The following signals can be connected to these BNC connectors : Connector name R G B H V RGBHV R G B H V RGBS R G B S - RGsB R Gs B - - Composite Video² - Video - - - Super Video² - Y - - C Component Video - SS² R-Y Y B-Y S - Component Video - SOY² R-Y Ys B-Y - - Input signal ² These source are optional for the BARCOREALITY SIM6. How to select input Slot 1 Key in 1 on the RCU or the local keypad. Configuration of the 5-cable input The configuration has to be done on the 'Input slot' menu. To change the signal format : 1 2 3 4 5 6 7 Press ADJUST or ENTER key to start up the Adjustment mode (menu 1). Push the cursor key é or ê to select Installation Press ENTER. Press the cursor key é or ê to select 'Input Slots' (menu 2) Press ENTER. The internal system will scan the inputs and displays the result in the 'Input Slots' menu. Push the cursor key é or ê to select the first slot (menu 3). Press ENTER key to toggle the input signal priority. ADJUSTMENT MODE INSTALLATION Select a path from below : INPUT SLOTS 800 PERIPHIRAL CONFIGURATION OSD COLOR RANDOM ACCESS INSTALLATION SERVICE Select with ê or é then <ENTER> <EXIT> to return. Select with ê or é then <ENTER> <EXIT> to return. menu 1 4-4 menu 2 INPUT SLOTS SLOT SELECTOR [Automatic] x - 1. 2. 3. 4. 5. 6. RGB [HS&VS] RGB [HS&VS] VIDEO S-VIDEO DIGITAL INPUT IEEE 1394 Select with ê or é then <ENTER> <EXIT> to return. menu 3 5976135 BARCOSIM 6 21032000 Connections Possible indication : RGB [HS&VS] = RGB analog signals, separate sync is horizontal and vertical sync. RGB CS = RGB analog signals, separate sync is composite sync. RGB CV = RGB analog signals, separate sync is composite video or tri-level sync. RGB-SOG = RGB analog signals, sync on green is composite sync. ²COMPONENT VIDEO - CS = separate sync is composite sync. ²COMPONENT VIDEO = component video with composite sync on Y or composite tri-level sync on Y. ²VIDEO ²S-VIDEO ² Optional for BARCOREALITY SIM6 Note for RCVDS05 users When using an RCVDS 05 with a 5 cable output module, connect these 5 cables to this 5-cable input slot (slot1) of the projector. All sources of the RCVDS can now be accepted by the projector. Audio connection (optional) Connect the audio input to one of the 3 audio inputs. See 'audio configuration' in this chapter for more explanation. Computer input/Monitor output² ² Monitor output is optional for the SIM6. Connect the output of the graphical card of the computer to the Computer input of the projector (connection < 60 cm) or insert an interface between the output of the computer and the input of the projector. Connect the monitor of the computer to the monitor output of the projector. This monitor output is only available when the computer input is used as input. RC 3 VIDEO R G S-V IDEO B 4 H/C SDI SDO V 1 5 IEEE 1394 COM PUTER 6 TRIG 2 M ONITO R M OUSE RS232 IN AUDIO IN RS232 O UT A AUDIO IN B COM M. PORT AUDIO IN C AUDIO IN Pin configuration of the D15 connector : 1 2 3 4 5 6 7 RED GREEN BLUE loop through to monitor ground ground ground 5976135 BARCOSIM 6 21032000 8 9 10 11 12 13 14 15 ground loop through to monitor ground loop through to monitor loop through to monitor horizontal/composite sync vertical sync loop through to monitor 4-5 Connections How to select Slot 2 Key in 2 on the RCU or the local keypad. Video Input (Optional) What can be connected Composite video signals from a VCR, OFF air signal decoder, etc... 1 x BNC or cinch 1.0Vpp ± 3 dB No loop through. RC 3 VIDEO R G S-VIDEO B 4 SDI H /C SDO IEEE 1394 C OMPU TER 1 V 5 6 TRIG 2 MON ITO R MOU SE R S232 IN C OM M. PO R T R S232 O UT A AUD IO IN AUD IO IN B AUDIO IN C AUD IO IN A, B or C C o m p o site V id e o or or T V tu n e r, e .g . M a rc o P o lo VCR How to select Slot 3 Key in 3 on the RCU or the local keypad. S-Video Input (optional) What can be connected Separate Y-luma/C-chroma signals for higher quality playback of Super VHS-signals. RC 3 VIDEO R G S-VIDEO B 4 H/C SDI SDO V 1 5 IEEE 1394 COM PUTER 6 T RIG 2 MONITO R M OUSE RS232 IN AUDIO IN RS232 O UT A AUDIO IN B COM M. PO RT AUDIO IN C AUDIO IN A, B or C Lum a/Chroma VCR S-VHS 4-6 5976135 BARCOSIM 6 21032000 Connections Pin configuration mini DIN plug 1 2 3 4 ground luminance ground chrominance luminance 1.0Vpp ± 3 dB chrominance 282 mVpp ± 3 dB How to select Slot 4 Key in 4 on the RCU or the local keypad. Serial Digital Input / Serial Digital Output (optional) What can be connected to this input ? Full compatibility with digital Betacam, or digital video sources. This avoids the need for analog processing anywhere in the video production chain and guarantees the ultimate image quality. An active loop through of the SDI input signal is provided for monitoring or for double or triple stacking applications. RC 3 V IDEO R G S-VIDEO B 4 H/C SDI SDO V 1 5 IEEE 139 4 COM PUTER 6 TRIG 2 M ONITOR M OUSE RS23 2 IN A UDIO IN RS232 OUT A AUDIO IN B COM M. PORT AUDIO IN C A UDIO IN D ig ita l V id e o D IG IT A L V ID E O S O U R C E connections : 1 x BNC input and 1 x BNC output. The input is always 75 W terminated. The output impedance of the SDO is 75 W. How to select Slot 5 Key in 5 on the RCU or the local keypad. Note : When a RCVDS05 is connected to the projector, the SDI input is available by keying in 85 on the RCU. IEEE 1394 Input Input not yet implemented. 5976135 BARCOSIM 6 21032000 4-7 Connections RS232 Connection RS232 in / RS232 out To connect a Computer, e.g. IBM PC (or compatible), Apple Macintosh to the RS 232 input of the projector to allow communicate between the computer and the projector. RC 3 VIDEO R G S-VIDEO B 4 H/C SDI SDO V 1 5 IEEE 1394 C OM PUTER 6 TRIG 2 MON ITO R MOU SE R S232 IN AUD IO IN RS232 OUT A AUDIO IN B C OMM. POR T AUD IO IN C AUD IO IN 56 FRQQHFWLRQ Applications : a) remote control : - easy adjustment of projector via IBM PC (or compatible) or MAC connection. - allow storage of multiple projector configurations and set ups. - wide range of control possibilities. - address range from 0 to 255. b) data communications : - sending data to the projector or copying the data from the projector to a hard memory device (hard disc, floppy, etc.). Set up of the Baud Rate for Communication with a Computer : See 'Change Baudrate PC' in chapter 'Service mode'. Communication port for communication with peripherals Configurations of the port. This port can be configured to accept PPM or RC5 coded signals. To change the port configuration see 800 Peripherals in Chapter Installation. Connecting a RCVDS 05 to the projector. - Up to 20 inputs with the RCVDS 05 and 90 inputs when RCVDS's are linked via the expansion module. Serial communication with the projector. Remote control buttons on the RCVDS to control the projector (source selection and analog settings). The selected source number will be displayed on a 2 digit display and the selected input module will be indicated with a LED on the rear. For more information about the use of the RCVDS 05, consult the owner's manual of the RCVDS05. TRIG Output 5 V output voltage to trigger an external device (max. 10mA). This voltage is available when the projector is on. 4-8 5976135 BARCOSIM 6 21032000 Connections MOUSE When available ? Mouse function is only available with the Executive Remote Control (Order number : R9829960). The computer can then be controlled via the projector. How to activate ? To activate this mouse function, handle as follow : 1 Start up your computer with the computer mouse plugged in. The mouse driver should be loaded. 2 Unplug the computer mouse without switching off the computer. 3 Plug the delivered cable between the mouse input of the computer and the mouse output of the projector. 4 Computer can now be controlled with the executive remote control. For more information about the mouse buttons or functions, consult the owner's manual of the Executive Remote Control. Warning : before swithing off, disconnect first the mouse cable. Available Mouse Functions Left click, right click or double click are the same as for a traditional mouse. For Click and drag : push for 2 seconds on the left (right) mouse button, the move the mouse arrow with the mouse navigator and click again very short on the left (right) mouse button to interrupt the drag function. Audio Connections (optional) What is available ? Three audio inputs and one audio output are available. Each audio input can be associated with an input source using the control software of the projector. e.g. source 1 can be locked with audio input B. How to lock an audio input ? Locking an audio input to a source input : 1 2 3 4 5 6 7 8 9 Press Press Press Press Press Press Press Press Press ENTER to start up the adjustment mode. the cursor key é or ê to select 'Random Access'. ENTER to display the Random Access menu. the cursor key é or ê to select 'Audio Tuning'. ENTER to display the Audio Tuning menu. the cursor key é or ê to select 'Video-Audio lock'. the cursor key ç or è to select the desired source input. ENTER to toggle between [A], [B] or [C]. several times EXIT or ADJUST to return to the operational mode. See also 'Video - Audio lock' in chapter 'Random Access Adjustment Mode'. 5976135 BARCOSIM 6 21032000 4-9 Connections 4-10 5976135 BARCOSIM 6 21032000 Getting Started 5 GETTING STARTED Remote Control & Local Keypad How controlling the projector ? The projector can be controlled by the local keypad or by the remote control unit. Location of the local keypad The local keypad is located on the backside of the projector. Remote control This remote control includes a battery powered infrared (IR) transmitter that allows the user to control the projector remotely. This remote control is used for source selection, control, adaptation and set up. It includes automatic storing of : - picture controls (Brightness, Sharpness...) - settings Other functions of the remote control are : - switching between standby and operational mode. - switching to "pause" (blanked picture, full power for immediate restarting) - direct access to all connected sources. Overview of Terminology EXIT STANDBY TEXT SHARPN TINT BRIGHTN PHASE COLOR &2175$67 ENTER PAUSE ) ) ) ) ) $'- (;,7 6+$531 (17(5 3$86( 7(;7 3+$6( 7,17 &2/25 %5,*+71 &2175 75(%/( %$/$1&( %$66 92/ Local keypad Remote Control (RCU) 5976135 BARCOREALITY SIM6 21032000 5-1 Getting Started 1 Function keys : user programmable keys with functions for direct access. 2 ADJ. : ADJUST key, to enter or exit the adjustment mode. 3 Address key (recessed key), to enter the address of the projector (between 0 and 9). Press the recessed address key with a pencil, followed by pressing one digit button between 0 and 9. 4 Selection key (*) : to direct access the zoom/focus/shift functions. 5 PAUSE : to stop projection for a short time, press 'PAUSE'. The image disappears but full power is retained for immediate restarting. 6 STBY : stand-by button, to start projector when the power switch is switched on and to switch off the projector without switching off the power switch. Attention : Switching to Stand-by. When the projector is running and you want to go to stand-by, press the stand-by key for 2 seconds until the message 'Saving data, please wait' is displayed. Do not press any longer on the stand-by key otherwise the projector will restart. 7 Mute : to interrupt the sound reproduction. 8 ? : not implemented. 9 Digit buttons : direct input selection. 10 Audio controls : use these buttons to obtain the desired sound level. 11 Picture controls : use these buttons to obtain the desired picture analog level. 12 PHASE : used to remove the instability of the image. 13 FREEZ : press to freeze the projected image. 14 TEXT : when adjusting one of the image, e.g. controls during a meeting, the displayed bar scale can be removed by pressing 'TEXT' key first. To re-display the bar scale on the screen, press 'TEXT' key again. 15 ENTER : to start up the adjustment mode or to confirm an adjustment or selection in the adjustment mode. 16 Cursor Keys (on RCU) or '+' and '-' keys (cursor keys) on the local keypad : to make menu selections when in the adjustment mode or to zoom/focus when the direct access is active. Comparision between the cursor keys and the use of the '+' and '-' keys on the local keypad : RCU = local keypad cursor key up = '+' key up cursor key down = '-' key down cursor key right = '+' key right cursor key left = '-' key left Use the '+' and '-' keys (cursor keys) : to increase or decrease the analog level of the image controls when they are first selected. 17 EXIT : to leave the adjustment mode or to scroll upwards when in the adjustment mode. 18 RC operating indication : lights up when a button on the remote control is pressed. (This is a visual indicator to check the operation of the remote control) Operating the Projector Switching on Use the power switch to switch on. When '0' is visible, the projector is switched off. When '1' is visible, the projector is switched on. When switching on with the power switch, the projector starts in the stand by mode. The projector mode indication lamp is red. To start image projection : a. press the 'Stand by' button once on the local keypad or on the remote control. The projector mode indication lamp will be green. b. press a digit button to select an input source. The projector mode indication lamp will be green. 5-2 5976135 BARCOREALITY SIM6 21032000 Getting Started Lamp Run Time When the total run time of the lamp is X-30 hours or more, the following warning message will be displayed for 1 minute. This warning message will be repeated every 30 minutes. Press EXIT to remove the message before the minute is over. Remaining Lamp run time 20 h When the total run time of the lamp is X hours or more, the following warning message, with the exact run time is displayed on the screen. Lamp run time is X hours. Operating the lamp longer than X hours may damage the projector. Please replace the lamp. WARNING Lamp run time is X hours Operating the lamp longer than X hours may damage the projector. Please replace the lamp <ENTER> to continue When OK (ENTER) is pressed to go on, the warning will be repeated every 30 min. The total lifetime of the lamp for a safe operation is X hours max. Do not use it longer. Always replace with a same type of lamp. Call a BARCO authorized service technician for lamp replacement. Lamp Run Time Warning Using a lamp for more than X hours is dangerous as the lamp could explode. Switching to Stand-by. When the projector is running and you want to go to stand-by, press the stand-by key for 2 seconds until the message 'Saving data, please wait' is displayed. Do not press any longer on the standby key otherwise the projector will restart. Saving data, Please wait Switching Off To switch off: - First press STANDBY key for 2 seconds. When the message 'Saving data, please wait' is displayed, do not press any longer on the standby key otherwise the projector will restart. Let cool down the projector at least 10 min. - Switch off the projector with the power switch. Switching to Stand-by Warning When switching to standby, it is possible to restart within the first 5sec.. When not restarted within these first 5 sec., the projector waits for 1 min. to restart again. During this period the LED display will show a jumping square with a dash. After one minute, two dashes will be displayed and the projector can restart. Quick Set Up Adjustments Quick Lens Adjustment For a quick lens set up and image shift, press the Selection key (* key), to display inmediately the zoom/focus menu. Only available for motorized lenses. For a quick set-up, handle as follow : A. Zoom/focus of the lens. 1 2 3 Press the Selection key. The zoom/focus menu will be displayed. Push the cursor key é or ê to zoom and ç and è to focus the image. When finished, press EXIT key to return or ENTER to continue to the shift adjustment. 5976135 BARCOREALITY SIM6 21032000 5-3 Getting Started ZOOM/FOCUS ZOOM with éor ê FOCUS with çor è <ENTER> to Shift <EXIT> to return B. Image shift 1 2 3 4 Press the selection key. The zoom/focus menu will be displayed. Press ENTER. The shift menu will be displayed. Push the cursor key é or ê to shift the image up or down and ç and è to shift the image left and right. When finished, press EXIT key to return or ENTER to continue to zoom/focus. SHIFT SHIFT with éor ê, çor è <ENTER> to Shift <EXIT> to return Quick On Screen Color change For quick change of the the on-screen color of the highlighted items. The highlighted items on the menus can be displayed in red, green or yellow. For a quick set-up, handle as follow : 1 2 3 4 5 6 7 Press ENTER to start up the adjustment mode. Push the cursor key é or ê to highlight 'Installation'. Press ENTER to display Installation menu. Push the cursor key é or ê to highlight 'OSD Color'. Press ENTER to display the OSD color menu. Push the cursor key é or ê to highlight the desired color. Press ENTER to select. ADJUSTMENT MODE INSTALLATION INPUT SLOTS 800 PERIPHERALS CONFIGURATION OSD COLOR NO SIGNAL INTERNAL PATTERNS QUICK ACCESS KEYS LENS MENU POSITION Select with é or ê then <ENTER> <EXIT> to return. Select a path from below : RANDOM ACCESS INSTALLATION SERVICE Source 01 Select with é or ê then <ENTER> <EXIT> to return. menu 1 5-4 menu 2 OSD COLOR HIGHLIGHTED ITEM RED GREEN YELLOW Select with é or ê then <ENTER> <EXIT> to return. menu 3 5976135 BARCOREALITY SIM6 21032000 Getting Started Using the RCU Pointing to the reflective screen Point the front of the RCU to the reflective screen surface. Ceiling Screen IR sensor RCU Hardwired Remote Input. Plug one end of the remote cable in the connector on the bottom of the RCU and the second side in the connector in the front panel of the projector labelled 'RC'. RC 3 V IDE O G R S -VIDE O B 4 SDI 5 SDO H /C COMPUTER 1 V I EE E 13 94 6 TRIG 2 MON ITO R MO USE RS23 2 IN AUDIO IN CO MM. PO RT RS232 O UT A B AUDIO IN A UD IO IN C AUDIO IN Directly to one of the IR sensors of the projector. When using the wireless remote control, make sure you are within the effective operating distance (30m, 100ft in a straight line). The remote control unit will not function properly if strong light strikes the sensor window or if there are obstacles between the remote control unit and the projector IR sensor. RC VID E O R 3 G S - VID EO 4 B H/ C SD I S DO V 1 5 IE EE 13 94 COM P UT ER 6 TR IG 2 MON ITOR MOU S E RS 23 2 IN A U D IO IN R S2 32 OU T A A U D IO IN B C OM M. PO RT AU D IO IN C AU D IO IN ) ) ) $ '- ) ) ) ) (;,7 ) ) ) $'- (;,7 (17( 5 (17( 5 3$86( 3$86( 7(;7 7(;7 3+ $6 ( 3+ $6 ( 6 +$ 531 7,17 7,17 & 2/25 & 2/25 % 5 ,*+ 71 % 5 ,*+ 71 & 2175 & 2175 6 +$ 531 75(% /( %$ /$ 1&( 75(% /( %$ /$ 1&( %$ 66 92/ %$ 66 92/ 5976135 BARCOREALITY SIM6 21032000 5-5 Getting Started Projector address Why a projector address ? As more than one projector can be installed in a room, the seperate projector should be seperately addressable wiht an RCU or computer. There for each projector has its own address. Set up an Individual Projector Address. The set up of a projector address cab be done via de software. See 'Change projector address' in chapter 'Service mode'. How to control the projector or projectors. Every projector requires an individual address between 0 and 255 which can be set in the Service mode. When the address is set, the projector can be controlled now: - RCU for addresses between 0 and 9. - computer, e.g. IBM PC (or compatible), Apple MAC, etc. for addresses between 0 and 255. Note : a projector will respond to a RCU set to the common address ('0' or '1') regardless of what address is set in the projector itself. Before using the RCU. The RCU is default programmed with address 0 or 1, 'common address'. With that 'common address' programmed into the RCU, every projector, without exception will listen to the commands given by this RCU. If it is necessary to control a specific projector, than enter the projector address into the RCU (only when that address is between 0 and 9). The projector with the corresponding address will listen to that specific RCU. Common Address Every projector has a common address '0' or '1'. The choice between '0' and '1' can be selected in the Service mode. Displaying the Projector Address on the Screen. Press the ADDRESS key (recessed key on the RCU) with a pencil. The projector's address will be displayed in a 'Text box'. This text box disappears after a few seconds. PROJECTOR ADDRESS 001 To continue using the RCU with that specific address, it is necessary to enter the same address with the digit buttons (address between 0 and 9) within 5 seconds after pushing the address key. For example : if the Address key displays projector address 003, then press "3" digit button on the RCU to set the RCU's address to match the projector's address. Do not press 003 digits. This will address the remote control to '0' and control all projectors in the room. If the address is not entered within 5 seconds, the RCU returns to its default address (zero address) and control all projectors in the room. How to Program an Address into the RCU? Press the ADDRESS key (recessed key on the RCU) with a pencil and enter the address with the digit buttons within 5 seconds after pushing the address key. That address can be any digit between 0 and 9. 5-6 5976135 BARCOREALITY SIM6 21032000 Getting Started Controlling the Projector Input Selection Key in the corresponding slot number with the digit keys on the RCU. The selected source will be displayed. Picture controls. When an image control is pressed, a text box with a bar scale, icon and function name of the control, e.g. 'brightness...' appears on the screen (only if text is ON). See example screen. The length of the bar scale and the value of the numeric indication indicate the current memorized setting for this source. The bar scale changes as the control stick on the RCU is pressed or the + or - buttons on the local keypad. BRIGHTNESS 0 127 Brightness Control A correct 'brightness' setting is important for good image reproduction. Use the + button for a higher brightness. Use the - button for a lower brightness. Contrast Control A correct 'contrast' setting is important for good image reproduction. Adjust the contrast to the level you prefer, according to room lighting conditions. Use the + button for a higher contrast. Use the - button for lower contrast. Color Saturation (optional) Color saturation is only active for Video and S-Video. Adjust the color intensity of the picture. Use the + button for richer colors. Use the - button for lighter colors. Tint Control (optional) Tint is only active for Video and S-Video when using the NTSC 4.43 or NTSC 3.58 system. Use the + button Use the - button. Sharpness Control. Use the + button for a sharper picture. Use the - button for a softer picture. Phase Control Use the control disc to adjust the phase. Freez key Press Freez to freeze the displayed image. Sound Controls (optional). When a sound control is pressed, a text box with a bar scale, icon and function name of the control, e.g. 'volume...' appears on the screen (only if text is ON). See example screen. The length of the bar scale indicates the current memorized setting for this source. The bar scale changes as the + or - buttons of the control are pressed. The picture controls can only be adjusted with the RCU. 5976135 BARCOREALITY SIM6 21032000 5-7 Getting Started Volume Control Volume control adjusts the volume. Use the + button for a higher volume. Use the - button for a lower volume. Bass Control Bass control adjusts the bass level (low tones). Use the + button for more low tones. Use the - button for less low tones. Treble Control Treble control adjusts the treble level (high tones). Use the + button for more high tones. Use the - button for less hight tones. Balance Control Is only effective if a external amplifier with loudspeakers is connected to the audio output. The balance control adjust the sound level between the left and the right box. Use the + button for a higher sound level on the right box than on the left one. Use the - button for a higher sound level on the left box than on the right one. The Pause key. When the Pause key is pressed, the image projection is stopped, a blue screen will be displayed and the projector remains with full power for immediate restart. The sound is not interrupted. The display on front of the projector will show a "P". To restart the image : 1 2 3 press pause key, press exit key or select a source number. The Selection key. See Quick Lens Adjustment in this chapter; 5-8 5976135 BARCOREALITY SIM6 21032000 Start up of the Adjustment Mode 6 START UP OF THE ADJUSTMENT MODE Adjustment Mode Start Up All source parameters, picture and audio tuning, and geometry are made while in the 'Adjustment Mode'. Press the ADJUST or ENTER key to enter the 'Adjustment mode'. You are now in the 'Adjustment Mode'. 1 2 3 The cursor key (RCU) or '+ or '-' keys (local keypad) are used to make menu selections and also for adjustments. The ENTER and EXIT keys are used to move forward and backward through the menu structure. The ADJUST key can be used to terminate the adjustment mode while any path selection menu is displayed. ADJUSTMENT MODE Select a path from below : RANDOM ACCESS INSTALLATION SERVICE Source 01 Select with é or ê then <ENTER> <EXIT> to return. menu 1 Possible Paths There are 3 possible paths to follow once in the Adjustment Mode. They are : Installation - Installation should be selected if a new input module is installed or a new source is connected to an existing input module. Also when the projector is relocated in a new configuration. Random Access - Random Access should be selected to set up a new source. Service - Service should be selected if the user intends to change general settings such as password, language, address, etc.or some service actions as reset lamp run time, panel adjustments, etc. or get set-up information. Password Protection Some items in the Adjustment mode are password protected. While selecting such an item, the projector asks to enter your password (Password protection is only available when the password strap on the controller module is ON, call an authorised service center to change the position of the password strap). Entering the Password PASSWORD ENTER PASSWORD ---Use numeric keys <EXIT> to return The password contains 4 digits. Enter the digits with the numeric keys. Example : 2 3 1 9 The first digit position is highlighted. Enter with the numeric keys. The highlighted square jumps to the next position. Continue until all 4 digits are filled in. 5976135 BARCOREALITY SIM6 21032000 6-1 Start up of the Adjustment Mode When your password is correct, you gain access to the selected item. When your password is wrong. The error message "Invalid password" is displayed on the screen. Press EXIT to continue and to return to the Service menu. Error Invalid password <EXIT> to return Factory programmed password : 0000 Once the password is correctly entered, all other password protected items are accessible without re-entering the password. Remark When re-entering the Adjustment mode, it will be nessary to enter the password again when selecting a password protected item. Setting up your own password See 'Changing password' in the Service mode. 6-2 5976135 BARCOREALITY SIM6 21032000 Random Access Adjustment Mode 7 RANDOM ACCESS ADJUSTMENT MODE Random Access Mode Overview Flowchart LOAD EDIT RENAME FILE SERVICE COPY DELETE OPTIONS CTI COLOR TEMPERATURE MOTION COMPENSATION RANDOM ACCESS ADJUSTMENT MODE GAMMA PICTURE TUNING DECODING COLOR DEPTH BLACK COLOR INPUT BALANCE SHIFT SIZE SIDE KEYSTONE GEOMETRY BLANKING ASPECT RATIO OPTIONS VOLUME BALANCE BASS TREBLE AUDIO TUNING MUTE FADE MODE STEREO/MONO VIDEO - AUDIO LOCK TYPE SOFT EDGE SIZE Optional DEMO 5976135 BARCOREALITY SIM6 21032000 7-1 Random Access Adjustment Mode Starting Up Push the cursor key é or ê to highlight 'Random Access' and then press ENTER. ADJUSTMENT MODE Select a path from below : RANDOM ACCESS INSTALLATION SERVICE Source 01 Select with é or ê then <ENTER> <EXIT> to return. Picture Service Connecting a new Source. Before using a new source, a correct file has to be installed. The projector's memory contains a list of files corresponding to the most used sources. When the new source corresponds with one of these files, the file can be loaded and saved for future use. When there is a little difference, the file can also be loaded and then edited until the source specs are reached. Note : file loading can be done automatically (see File Options, in this chapter). Files with a ~ in front of the file name are tempory files. These files will be deleted when switching to another source. Start up the File Service. To enter the File Service, handle as follow : 1 2 Pushing the cursor key é or ê to highlight 'File Service' (menu 1). Press ENTER to select. The File service menu will be displayed (menu 2). Note : EXIT returns to the Path selection menu. ADJUST returns to operational mode. RANDOM ACCESS ADJUSTMENT MODE FILE SERVICE FILE SERVICE PICTURE TUNING AUDIO TUNING GEOMETRY LOAD EDIT RENAME COPY DELETE OPTIONS Select with é or ê then <ENTER> <EXIT> to return. Select with é or ê then <ENTER> <EXIT> to return. menu 1 menu 2 Possible File Manipulations. The following file manipulations are possible : - Load : installation of a file for a new source. - Edit : editing a loaded file to the source specs. - Rename : renaming a file. - Copy : copying a file to a new file. - Delete : deleting an existing file. - Options : way of sorting the files. File Annotation. xxxxxxxx.xxx x xxxxXxxxxi i or blank : i = interlaced, blank = not interlaced xxxxXxxxx : active pixel rating x : source number xxx : file extension, first character is C (for custom made files) or S (for standard files). The second and third character is used for a following number (=file index) file index for custom files : 00 to 63. xxxxxxxx : base name, 8 characters. 7-2 5976135 BARCOREALITY SIM6 21032000 Random Access Adjustment Mode Load File Start up the Load File Push the cursor key é or ê to highlight 'Load' (menu 1). Press ENTER to select. The Load menu displays the corresponding files depending on the installed filter (menu 2). 1 2 This filter can be "Fit" or "All". To change the filter : 1 Push the cursor key è or ç highlight 'filter list'. 2 Press ENTER to toggle the annotation between brackets. "All" : all files that can be loaded will be displayed. "Fit" : only the best fitting files will be displayed (with a distinction of ± 2 lines and line duration distinction of ± 300 ns, if nothing is found within this small area, the projector continues searching until it finds something.) FILE SERVICE LOAD EDIT RENAME COPY Select with é or ê then <ENTER> <EXIT> to return. menu 1 LOAD FILE FILTER LIST [All] Filename Src Resolution ----------------------------------------------------Video525.s01 1 675x240i Video525.c01 1 675x240i Video525.c02 1 675x240i ----------------------------------------------------Active file : Video525.c50 Select with é or ê ,è <ENTER> to accept <EXIT> to return. menu 2 How to load a file ? Push the cursor key é or ê to select the best fitting file. Press ENTER to select. A confirm Load file menu will be displayed with the newly created file and the one on which the new file is based on. Press ENTER to confirm the new creation or EXIT to return to the load file menu. 1 2 3 During a load file, the actual active file is displayed next to the indication 'Active file'. Note: When scrolling through the files, the image will be adapted according to the settings of the selected file (on line adaptation). CONFIRM LOAD FILE LOAD FILE FILTER LIST [All] Filename Src Resolution ----------------------------------------------------Video525.s01 1 675x240i Video525.c01 1 675x240i Video525.c02 1 675x240i Create file Video525.c02 based on file Video525.s01? ----------------------------------------------------Active file : Video525.c50 Select with é or ê ,è <ENTER> to accept <EXIT> to return. menu 1 <ENTER> to confirm <EXIT> to return menu 2 The image is not perfect ? If the displayed image is not correct after selecting the best fitting file, go to the Edit menu, select the active file and change the File settings. Edit File What can be done with the Edit File menu ? The Edit file menu makes it possible to change the settings of the file according to the real settings of the connected source. Consult the source specification before entering the data. 5976135 BARCOREALITY SIM6 21032000 7-3 Random Access Adjustment Mode How to start up the Edit menu ? To start up the EDIT menu: 1 Push the cursor key é or ê to highlight 'Edit'. 2 Press ENTER to select. The Edit file adaptation menu will be displayed. 3 Select the file which must be edited (mostly the active file). 4 Press ENTER. The file name will be displayed in the upper right corner. FILE SERVICE LOAD EDIT RENAME COPY Select with é or ê then <ENTER> <EXIT> to return. menu 1 EDIT FILE Filename Src Resolution ----------------------------------------------------Video525.s01 1 675x240i Video525.c01 1 675x240i Video525.c02 1 675x240i ----------------------------------------------------Active file : Video525.c50 Select with é or ê ,ç <ENTER> to accept <EXIT> to return. menu 2 Which items can be adjusted ? The following items can be adjusted : Total quantity horizontal pixels Active quantity horizontal pixels Horizontal start in pixels Horizontal period in µs (is automatically adapted during the installation of a file with LOAD) Total vertical lines (is automatically adapted during the installation of a file with LOAD) Active vertical lines Vertical start in lines Interlaced : toggle on/off (is automatically set to its correct position during the installation of a file with LOAD) All settings can individually be changed. EDIT FILE HORIZONTAL TOTAL ACTIVE START PERIOD VERTICAL (FIELD) TOTAL ACTIVE START INTERLACED READ AMDS OPTIONS xga.s30 1344 PIXELS 1024 PIXELS 296 PIXELS 20.678 µS 806 LINES 768 LINES 36 LINES [OFF] é,ê,ç ,è <ENTER>, <EXIT> How to change the settings ? 1 Push the cursor key é or ê to select an item. The color of the selected item will change and follow one of the three methods to change the value. a. method 1: 1 press ENTER to activate the digits 2 enter directly with the numeric keys on the RCU or local keypad the new value or b. 1 2 3 4 method 2: Press ENTER to activate the digits Push the cursor key è or ç to select the changing digit. Push the cursor key é or ê to scroll to desired digit. When finished press ENTER to confirm. c. method 3 1 Counting up or down by pushing the cursor key è or ç . How to find the correct values for the displayed item? During the installation of a file with LOAD, the horizontal period, the total number of vertical lines and the interlaced mode are automatically measured and filled in in the menu table. These values will be available when starting up the EDIT procedure of an active file. (Caution : Do not adjust these settings on an active file, they are used to identify the input source file.) 7-4 5976135 BARCOREALITY SIM6 21032000 Random Access Adjustment Mode If the value for "Horizontal Total Pixels" is wrong, sampling mistakes (small vertical bars in the projected image) will be seen in the image. Select "Total" and adjust the pixel quantity. Adjust for zero bars (hint: if the number of bars increase, adjust in the other direction). The "Active Pixels" : determine the width of the window on the screen. This value is normally given in the source specifications. If not, adjust until full image is displayed (no missing pixels). "Horizontal Start" : number of pixels between the beginning of the input signal and the start of the video information in the signal. "Horizontal Period" : already filled in with the correct value when active file. (see caution above). The "Vertical Total Lines" are already filled when an active file is selected to be edited (see caution above). The "Active Lines" : number of horizontal lines determining the height of the projected image. This value is normally given in the specification of the source. If not, adjust until full image height is displayed (no missing lines) Vertical start : number of lines between the start of the input signal and start of the image on the screen. Interlaced [On] or [Off] : this selection is automatically filled when active file has to be edited. If the image is wrong due to mismeasurement, use the ENTER key to toggle between [On] and [Off]. (for interlaced images, 1 frame contains 2 fields). Read AMDS AMDS = automatic mode detection & synchronisation During the installation of a file with LOAD, the system automatically measured the horizontal period, the total vertical lines and the interlaced mode. When selecting Read AMDS, the system remeasures the above indicated items. Options EDIT FILE OPTIONS Source number 1 Clamp position [leading] Clamp delay 0 Clamp width 10 Field polarity [pos] Field select [both] Vertical refresh [sync] Vertical sync polarity [leading] Select with é or ê <ENTER> to toggle ç or è to change value <EXIT> to return Source Number : The source number of a non-active source can be changed to any other source number. This makes it possible to create a file for future source numbers. Clamp Position : Clamping determines the black level of the signal. The clamp pulse can be related to the leading or the trailing edge of the sync pulse. Use the ENTER key to toggle between [leading] and [trailing]. Clamp Delay : The time between the leading edge of the clamp pulse and the locked edge of the sync pulse. Can be any value between 0 and 255. Change the value by pushing the cursor key è or ç. Clamp Width : The width of the clamp pulse Can be any value between 0 and 255. Change the value by pushing the cursor key è or ç. trailing edge leading edge Example for clamp position [trailing] Sync pulse Clamp pulse Clamp width Clamp delay 5976135 BARCOREALITY SIM6 21032000 7-5 Random Access Adjustment Mode Field Polarity : The field polarity function is used for interlaced images. Both rasters of the image could be shifted in a wrong way (double lines are visible in the image). This can be corrected by forcing the field polarity to [neg] or [pos]. Use the ENTER key to toggle between [pos] and [neg]. Field Select : Default [both] The field select is only used for interlaced images. One frame of an interlaced image contains two fields, an even and an odd field. The choice exists to project [both] fields on the screen or only the [even] or [odd] field. This can be useful for 3D projection. Use the ENTER key to toggle between [both], [even] and [odd]. Vertical Refresh [sync/async] : The way of updating the image information on the LCD panels. Not available for PAL-NTSC-SECAM sources. This option will be displayed in gray. 1 For sources with a vertical frequency up to 60 Hz : the vertical refresh rate is the same as the vertical frequency of the incoming source. This is a necessity to project moving images without 'motion artifacts'. For stationary images with a vertical frequency up to 60 Hz it is still possible to use asynchronous refresh. When loading Pal, Secam, NTSC-files the synchronous mode is default, for all other sources below 60 Hz asynchronous mode is default. 2 For sources with a vertical frequency higher that 60 Hz : the vertical refresh is different than the vertical frequency of the incoming source. Synchronous refresh cannot be used. Vertical Sync Polarity : [leading] or [trailing] The vertical refresh can be synchronised with the leading sync edge or trailing sync edge. Default on [leading]. Toggling to [trailing] is only necessary for special applications where the trailing edge of the sync signal has to be taken as a reference. Use the ENTER key to toggle between [leading] or [trailing] Press EXIT to leave the Edit File Option menu. A 'Confirm Edit File' menu will be displayed. CONFIRM EDIT FILE Save changes to file xga.c30? <ENTER> to confirm <EXIT> to return Rename a file Start Up To change the name of a selected file: 1 Push the cursor key é or ê to highlight 'Rename' (menu 1). 2 Press ENTER. The Rename selection menu will be displayed (menu 2). 3 Push the cursor key é or ê to select a file name (menu 2). 4 Press ENTER to select. The Rename menu will be displayed with the selected file name already filled in, leave in the 'From file name :' area and in the 'To file name :' area. The first character in the 'To file name :' area is highlighted (menu3). RENAME FILE FILE SERVICE LOAD EDIT RENAME COPY DELETE Select with é or ê then <ENTER> <EXIT> to return. menu 1 7-6 RENAME FILE Filename Src Resolution ----------------------------------------------------Video525.s01 1 675x240i Video525.c01 1 675x240i Video525.c02 1 675x240i Frome file name : Video525.s01 To file name : demo.c10 Select with ç or è Reprogram with é or ê or numeric keys <ENTER> to confirm <EXIT> to return ----------------------------------------------------Active file : Video525.c50 Select with é or ê <ENTER> to accept <EXIT> to return. menu 2 menu 3 5976135 BARCOREALITY SIM6 21032000 Random Access Adjustment Mode How to change the characters ? 1 2 3 4 Push the cursor key ç or è to select the desired character. Change that character by pushing the cursor key é or ê. Numeric characters can be entered directly with numeric keys on the RCU. Press ENTER to confirm. The renamed file is entered in the list of files. Press EXIT to return to the Rename menu selection. No changes are made. RENAME FILE Frome file name : Video525.s01 To file name : demo.c10 Select with é or ê Reprogram with ç or è or numeric keys <ENTER> to confirm <EXIT> to return menu 1 Copy a file Start Up To copy a selected file into a new file : 1 Push the cursor key é or ê to highlight 'Copy' (menu 1). 2 Press ENTER. The Copy selection menu will be displayed (menu 2). 3 Push the cursor key é or ê to select a file name (menu 3). 4 Press ENTER to select. The Copy menu will be displayed with the selected file name already filled in, in the 'From file name :' area and in the 'To file name:' area. The first character in the 'To file name :' is highlighted. FILE SERVICE LOAD EDIT RENAME COPY DELETE Select with é or ê then <ENTER> <EXIT> to return. menu 1 COPY FILE COPY FILE Filename Src Resolution ----------------------------------------------------Video525.s01 1 675x240i Video525.c01 1 675x240i Video525.c02 1 675x240i Frome file name : xga_60.s03 To file name : xga_60.c14 Select with ç or è Reprogram with é or ê or numeric keys <ENTER> to confirm <EXIT> to return ----------------------------------------------------Active file : Video525.c50 Select with é or ê <ENTER> to accept <EXIT> to return. menu 2 menu 3 How to change the characters ? 1 2 3 4 Push the cursor key ç or è to select the desired character (menu 4). Change that character by pushing the cursor key é or ê. Numeric characters can be entered directly with numeric keys on the RCU. Press ENTER to confirm. The renamed file is entered in the list of files. Press EXIT to return to the Copy menu selection. No changes are made. COPY FILE Frome file name : xga_60.s03 To file name : xga_60.c14 Select with ç or è Reprogram with é or ê or numeric keys <ENTER> to confirm <EXIT> to return menu 4 5976135 BARCOREALITY SIM6 21032000 7-7 Random Access Adjustment Mode Delete Start Up To delete a selected file out of the list of files : 1 Push the cursor key é or ê to highlight 'Delete' (menu 1). 2 Press ENTER. The delete selection menu will be displayed (menu 2). 3 Push the cursor key é or ê to select a file name. 4 Press ENTER to select. If [All] is selected, your password has to be entered before all files will be deleted. A confirmation menu "Delete file 'file name'?" is displayed (menu 3). When you want to delete the file, press ENTER. If you do not want to delete the file, press EXIT. Note : the active file cannot be deleted. FILE SERVICE LOAD EDIT RENAME COPY DELETE OPTIONS Select with é or ê then <ENTER> <EXIT> to return. menu 1 CONFIRM DELETE FILE DELETE FILE Filename Src Resolution ----------------------------------------------------Video525.s01 1 675x240i Video525.c01 1 675x240i Video525.c02 1 675x240i Delete file: Video525.c01? ----------------------------------------------------Active file : Video525.c50 Select with é or ê <ENTER> to accept <EXIT> to return. menu 2 <ENTER> to confirm <EXIT> to return menu 3 File Options Start Up 1 2 Push the cursor key é or ê to highlight 'File Options' (menu 1). Press ENTER. The option selection menu will be displayed (menu 2). FILE SERVICE FILE OPTIONS LOAD EDIT RENAME COPY DELETE OPTIONS FILE SORT [NAME] Select with é or ê then <ENTER> <EXIT> to return. Select with é or ê then <ENTER> <EXIT> to return. menu 1 menu 2 File Sort Press ENTER to toggle between [name] and [index] [name] : The files in the file list will be sorted on the file name. [index] : The files in the file list will be sorted on the file extension. 7-8 5976135 BARCOREALITY SIM6 21032000 Random Access Adjustment Mode Picture Tuning Start Up To improve the image quality, the items in the Picture Tuning menu can be toggled or adjusted. To start up the Picture Tuning : 1 2 Push the cursor key é or ê to highlight 'Picture Tuning' (menu 1). Press ENTER to select. The Picture Tuning menu will be displayed (menu 2). PICTURE TUNING RANDOM ACCESS ADJUSTMENT MODE FILE SERVICE PICTURE TUNING AUDIO TUNNING GEOMETRY SOFT EDGE DEMO Select with é or ê then <ENTER> <EXIT> to return. menu 1 CTI [ON] MOTION COMPENSATION COLOR TEMPERATURE GAMMA DECODING [EBU] COLOR DEPTH INPUT BALANCE BLACK COLOR Select with é or ê then <ENTER> <EXIT> to return. menu 2 Which items are available ? The next items are available : - CTI ON/OFF (optional) - motion compensation - color temperature - gamma - decoding EBU/IRE (optional) - color depth - input balance - black color CTI ON/OFF Optional What is CTI ? CTI : Color Transient Improvement. To improve the transition from one color to another. How to change thet CTI settings 1 2 Push the cursor key é or ê to highlight 'CTI'. Press ENTER to toggle between ON and OFF. PICTURE TUNING CTI [ON] MOTION COMPENSATION COLOR TEMPERATURE GAMMA DECODING [EBU] COLOR DEPTH INPUT BALANCE BLACK COLOR Select with é or ê then <ENTER> <EXIT> to return. Note : This function applies to PAL and NTSC video or S-video inputs only. Motion Compensation Optional What is motion compensation ? To change the response time of the LCD panels. The following options can be adjusted: - LCD speed - LCD speed R/G - LCD speed B/G 5976135 BARCOREALITY SIM6 21032000 7-9 Random Access Adjustment Mode How to start up ? 1 2 Push the cursor key é or ê to highlight 'Motion compensation' (menu 1). Press ENTER to select. The motion compensation menu will be displayed (menu 2). PICTURE TUNING PICTURE TUNING CTI [ON] MOTION COMPENSATION COLOR TEMPERATURE GAMMA DECODING [EBU] COLOR DEPTH INPUT BALANCE BLACK COLOR Select with é or ê then <ENTER> <EXIT> to return. LCD SPEED LCD SPEED R/G LCD SPEED B/G menu 1 Select with é or ê then <ENTER> <EXIT> to return. menu 2 LCD speed This will change the response time of the LCD's. Range 0 - 16 Default : 8 To change the response time : 1 Push the cursor key é or ê to highlight 'LCD speed' (menu 1). 2 Press ENTER to select. The image will be displayed with together with an adjustment box (menu 2). PICTURE TUNING LCD SPEED 8 LCD SPEED LCD SPEED R/G LCD SPEED B/G menu 2 Select with é or ê then <ENTER> <EXIT> to return. menu 1 LCD speed R/G This will change the response time of the Red LCD compared to the Green LCD. Range : 0 - 2 with steps of 0.125 Default : 1.00 To change the response time of the Red LCD panel : 1 Push the cursor key é or ê to highlight 'LCD speed R/G' (menu 1). 2 Press ENTER to select. The image will be displayed with together with an adjustment box (menu 2). PICTURE TUNING LCD SPEED R/G 1.00 LCD SPEED LCD SPEED R/G LCD SPEED B/G menu 2 Select with é or ê then <ENTER> <EXIT> to return. menu 1 LCD speed B/G This will change the response time of the Blue LCD compared to the Green LCD. Range : 0 - 2 with steps of 0.125 Default : 1.00 7-10 5976135 BARCOREALITY SIM6 21032000 Random Access Adjustment Mode To change the response time of the Red LCD panel : 1 Push the cursor key é or ê to highlight 'LCD speed R/G' (menu 1). 2 Press ENTER to select. The image will be displayed with together with an adjustment box (menu 2). PICTURE TUNING LCD SPEED R/G 1.00 LCD SPEED LCD SPEED R/G LCD SPEED B/G menu 2 Select with é or ê then <ENTER> <EXIT> to return. menu 1 Color Temperature Start Up Push the cursor key é or ê to highlight 'Color Temperature'. Press ENTER to select. The color temperature selection menu will be displayed. 1 2 PICTURE TUNING COLOR TEMPERATURE CTI [ON] MOTION COMPENSATION COLOR TEMPERATURE GAMMA DECODING [EBU] COLOR DEPTH INPUT BALANCE BLACK COLOR Select with é or ê then <ENTER> <EXIT> to return. menu 1 PROJECTOR WHITE COMPUTER 9300K VIDEO 6500K FILM 5400K BROADCAST 3200K CUSTOM BALANCE Select with é or ê then <ENTER> <EXIT> to return. menu 2 Available Color Temperature : - Projector white Broadcast Film Video Computer Custom balance. 3200 K 5400 K 6500 K 9300 K Adjusting the Color Temperature Push the cursor key up or down to select a fixed color temperature or custom balance. Projector white will provide maximum projector light output. The calibrated 'Broadcast', 'Film', 'Video' and 'Computer' presets will provide optimum color tracking. Custom balance allows the user to set his own preferred color temperature. Custom Balance To 1 2 3 adjust Custom Balance, handle as follow : Push the cursor key é or ê to highlight 'Custom Balance' (menu 1). Press ENTER to select. Push the cursor key é or ê to adjust red and push the cursor key ç or è to adjust blue (range 0 to 2.5) in comparison with the green color (menu 2). COLOR TEMPERATURE PROJECTOR WHITE COMPUTER 9300K VIDEO 6500K FILM 5400K BROADCAST 3200K GAIN RED 0 2.5 menu 2 CUSTOM BALANCE Select with é or ê then <ENTER> <EXIT> to return. menu 1 5976135 BARCOREALITY SIM6 21032000 7-11 Random Access Adjustment Mode Gamma What can be adjusted ? With the gamma correction adjustment, it is possible to accurately set the gamma of the projector image. How to change the gamma value ? 1 2 3 4 Push the cursor key é or ê to highlight 'Gamma' (menu 1). Press ENTER to select. Change the gamma value by pushing the cursor key ç or è until the desired value is reached (menu 2). Press EXIT to return to the Picture Tuning menu. Default value of gamma = 1.9 PICTURE TUNING CTI [ON] MOTION COMPENSATION COLOR TEMPERATURE GAMMA DECODING [EBU] COLOR DEPTH INPUT BALANCE BLACK COLOR Select with é or ê then <ENTER> <EXIT> to return. GAMMA = 1.9 3 menu 2 menu 1 Decoding EBU/IRE Optional Note : Only for NTSC signals. What can be done ? The possibility is offered to decode the NTSC video signals via the default American IRE standard or via the European EBU standard. Decoding a NTSC signal using the European EBU standard may result in a greenish tint. How can it be selected ? 1 2 3 Push the cursor key é or ê to highlight 'Decoding' (menu 1). Press ENTER to toggle between EBU or IRE. Press EXIT to return. PICTURE TUNING CTI [ON] MOTION COMPENSATION COLOR TEMPERATURE GAMMA DECODING [EBU] COLOR DEPTH INPUT BALANCE BLACK COLOR Select with é or ê then <ENTER> <EXIT> to return. menu 1 Color Depth Purpose Increases color saturation of dark colors. 7-12 5976135 BARCOREALITY SIM6 21032000 Random Access Adjustment Mode To change the Color depth value : 1 2 3 4 Push the cursor key é or ê to highlight 'Color Depth' (menu 1). Press ENTER to select. Change the value by pushing the cursor key ç or è until the desired dark color saturation is reached (menu 2). Adjustment range : 0 ... 8 Default : 4 Press EXIT to return to the Picture Tuning menu. PICTURE TUNING CTI [ON] MOTION COMPENSATION COLOR TEMPERATURE GAMMA DECODING [EBU] COLOR DEPTH INPUT BALANCE BLACK COLOR Select with é or ê then <ENTER> <EXIT> to return. COLOR DEPTH 4 0 8 menu 2 menu 1 Black Color Purpose Modifies the color of the black image for color matching between projectors. To change the black color : 1 2 3 Push the cursor key é or ê to highlight 'Black Color' (menu 1). Press ENTER to select. Change the color of the black image by adding a certain amount of Red (R), Green (G) or Blue (B). Notice : Deviation from R=0, G=0, B=0 will result in a lower contrast ratio for the projector. PICTURE TUNING CTI [ON] MOTION COMPENSATION COLOR TEMPERATURE GAMMA DECODING [EBU] COLOR DEPTH BLACK COLOR INPUT BALANCE Select with é or ê then <ENTER> <EXIT> to return. R G B menu 1 Input Balance Why adjusting the input balance ? The input balance is normally correct adjusted in the factory. But due to signal distribution or signal transmission, a color imbalance can be the result. This imbalance can be adjusted source by source for color critical applications. These adjustments influence only the actual custom adjustment file. This procedure is not so easy. Attention : Before starting the Input Balance function, generate a signal with dominant black and white areas. How to adjust the input balance ? The default values are normally loaded when selecting a source. If the image is not as desired, adjust for this source as follow : 1 2 Push the cursor key é or ê to highlight 'Input Balance' (menu 1). Press ENTER to select. The Input Balance menu will be displayed (menu 2). Start with the Black Balance : 1 Push the cursor key é or ê to highlight 'Black Balance' (menu 2). 2 Press ENTER to select. 3 Adjust the Brightness to a maximum value until there is just no green noise visible in the black areas. 4 Adjust with the cursor key é or ê or ç or è until there is no red or blue noise visible in the black areas. 5976135 BARCOREALITY SIM6 21032000 7-13 Random Access Adjustment Mode Continue with the White Balance : 1 Push the cursor key é or ê to highlight 'White Balance' (menu 2). 2 Press ENTER to select. 3 Adjust the Contrast to a maximum value until the white areas are just white (without green noice) and return one step. 4 Adjust with the cursor key é or ê or ç or è until there is no red or blue noise visible in the white areas. PICTURE TUNING INPUT BALANCE CTI [ON] MOTION COMPENSATION COLOR TEMPERATURE GAMMA DECODING [EBU] COLOR DEPTH BLACK COLOR INPUT BALANCE Select with é or ê then <ENTER> <EXIT> to return. WHITE BALANCE BLACK BALANCE menu 1 DEFAULT Select with é or ê then <ENTER> <EXIT> to return. menu 2 menu 3 Audio Tuning Optional Start Up 1 2 Push the cursor key é or ê to highlight 'Audio Tuning' (menu 1). Press ENTER to select. The Audio Tuning menu will be displayed (menu 2). RANDOM ACCESS ADJUSTMENT MODE FILE SERVICE PICTURE TUNING AUDIO TUNNING GEOMETRY SOFT EDGE DEMO Select with é or ê then <ENTER> <EXIT> to return. 1 [A] AUDIO TUNING VOLUME BALANCE BASS TREBLE MUTE [OFF] FADE MODE [STEREO] VIDEO - AUDIO LOCK 2 3 4 5 6 [C] [B] [A] [B] [A] Select with é or ê then <ENTER> <EXIT> to return. menu 1 menu 2 Available items - Volume Balance Bass Treble Mute Fade Mode Video - Audio lock Volume, Balance, Bass and Treble How to adjust ? When a sound control is selected by highlighting the item with the cursor key, a text box with a bar scale, icon and function name of the control, e.g. 'Volume' appears on the screen (only when text is ON). The length of the bar scale indicates the current memory setting for this source. For more information about the sound controls, see 'Sound controls with direct access' in the Chapter 'Controlling'. 7-14 5976135 BARCOREALITY SIM6 21032000 Random Access Adjustment Mode Mute Purpose To stop the sound reproduction. How to stop sound reproduction ? 1 2 1 [A] Push the cursor key é or ê to highlight 'Mute' (menu 1). Press ENTER to toggle between [on] or [off]. AUDIO TUNING VOLUME BALANCE BASS TREBLE MUTE [OFF] FADE MODE [STEREO] VIDEO - AUDIO LOCK 2 3 4 5 6 [C] [B] [A] [B] [A] Select with é or ê then <ENTER> <EXIT> to return. menu 1 Fade Purpose Determine where the sound signals will be reproduced, internally or externally. How to set up the fade ? Push the cursor key é or ê to highlight 'Fade' (menu 1). Press ENTER to select. Adjust the desired fade level. The fade can be adjusted between -15 and 15 (menu 2). 1 2 3 1 [A] AUDIO TUNING VOLUME BALANCE BASS TREBLE MUTE [OFF] FADE MODE [STEREO] VIDEO - AUDIO LOCK 2 3 4 5 6 [C] [B] [A] [B] [A] Select with é or ê then <ENTER> <EXIT> to return. FADE -15 0 15 menu 2 menu 1 Fade on -15 : no sound reproduction on the external loudspeakers, max on the internal loudspreaker with the same volume level as adjusted with the volume control. Fade on 15 : no sound reproduction on the internal loudspeakers but max on the external loudspeakers with the same volume level as adjusted with the volume control. Mode [stereo]/[mono] Purpose To switch the sound reproduction between mono and stereo. How to install the sound mode ? 1 2 1 [A] Push the cursor key é or ê to highlight 'Mode' (menu 1). Press ENTER to toggle between [stereo] or [mono]. AUDIO TUNING VOLUME BALANCE BASS TREBLE MUTE [OFF] FADE MODE [STEREO] VIDEO - AUDIO LOCK 2 3 4 5 6 [C] [B] [A] [B] [A] Select with é or ê then <ENTER> <EXIT> to return. menu 1 5976135 BARCOREALITY SIM6 21032000 7-15 Random Access Adjustment Mode Video - Audio lock Purpose An input source can be locked to an audio input. How to lock input source to an audio source ? 1 2 3 4 5 Push the cursor key é or ê to highlight the first input source (menu 1). Press ENTER to scroll the associated audio input between [A], [B] or [C]. Push the cursor key ç or è to highlight another input source. Press ENTER to scroll between [A], [B] or [C]. Continue for the other inputs in the same way. AUDIO TUNING VOLUME BALANCE TREBLE MUTE [OFF] FADE MODE [STEREO] VIDEO - AUDIO LOCK 2 3 4 5 6 [C] [B] [A] [B] [A] 1 [A] Select with é or ê then <ENTER> <EXIT> to return. menu 1 Geometry To start up the Geometry functions 1 2 Push the cursor key é or ê to highlight 'Geometry' (menu 1). Press ENTER to select. The geometry menu will be displayed (menu 2). GEOMETRY RANDOM ACCESS ADJUSTMENT MODE SHIFT SIZE SIDE KEYSTONE BLANKING ASPECT RATIO [5:4] OPTIONS FILE SERVICE PICTURE TUNING AUDIO TUNNING GEOMETRY SOFT EDGE DEMO Select with é or ê then <ENTER> <EXIT> to return. menu 1 Select with é or ê then <ENTER> <EXIT> to return. menu 2 Which Geometry adjustments are possible ? - horizontal and vertical image shift. horizontal and vertical image size side keystone (only necessary if the projector is mounted at a non standard projection angle). blanking aspect ratio options How can an adjustment be adjusted ? 1 2 7-16 Using the cursor key to adjust or Entering the value with the digit keys. Therefore, press ENTER to select the indicated value and enter the desired value with the digit keys. Press ENTER to confirm the entered value. 5976135 BARCOREALITY SIM6 21032000 Random Access Adjustment Mode Shift What can be done ? The image can be shifted in a horizontal or vertical direction. To start up the shift action : Push the cursor key é or ê to highlight 'Shift' (menu 1). Press ENTER to select. Push the cursor key é or ê to shift the image in a vertical direction. Push the cursor key ç or è to shift the image in a horizontal direction. The default value for the shift is 0. Shifting in a vertical direction : when the shift value is positive, the image is shifted upwards, when the value is negative, the image is shifted downwards. Shifting in a horizontal direction : when the shift value is positive, the image is shifted to the right, when the value is negative, the image is shifted to the left. 1 2 3 GEOMETRY SHIFT SIZE SIDE KEYSTONE BLANKING ASPECT RATIO [5:4] OPTIONS Select with é or ê then <ENTER> <EXIT> to return. menu 1 Size What can be done ? The size can be adjusted in a vertical or horizontal way. When adjusting the vertical size, The upper side of the image is fixed (table and ceiling mounted configurations) and only the lower side can be moved to its exact position. When adjusting the horizontal size, the left side of the image is fixed and only the right side can be moved to its exact position. To start up the size adjustment : 1 2 3 Push the cursor key é or ê to highlight 'Size' (menu 1). Press ENTER to select. Push the cursor key é or ê to size the image in a vertical direction. Push the cursor key ç or è to size the image in a horizontal direction. GEOMETRY Fixed sides SHIFT SIZE SIDE KEYSTONE BLANKING ASPECT RATIO [5:4] OPTIONS Horizontal size adjustment Select with é or ê then <ENTER> <EXIT> to return. menu 1 Vertical size adjustment Example for table mount configuration 5976135 BARCOREALITY SIM6 21032000 7-17 Random Access Adjustment Mode Side Keystone What can be done ? The side keystone adjustment is used to align the image if the projector is mounted at a nonstandard projection angle. Aligning the keystone 1 2 3 Push the cursor key é or ê to highlight 'Side Keystone' (menu 1). Press ENTER to select. Push the cursor key ç or è to adjust the keystone of the image. When the upper part of the image is wider than the lower part of the image, push the cursor key ç. The number indication below the bar scale will be negative. When the upper part of the image is smaller than the lower part of the image, push the cursor key è. The number indication below the bar scale will be positive. GEOMETRY SHIFT SIZE SIDE KEYSTONE BLANKING ASPECT RATIO [5:4] OPTIONS Select with é or ê then <ENTER> <EXIT> to return. menu 1 Blanking What can be done ? Blanking adjustments affect only the edges of the projected image and are used to frame the projected image on to the screen and to hide or black out unwanted information (or noise). A '0' on the bar scale indicates no blanking. Available Blanking Adjustments - top blanking bottom blanking left blanking right blanking Top blanking Right blanking Left blanking Bottom blanking 7-18 5976135 BARCOREALITY SIM6 21032000 Random Access Adjustment Mode Adjusting the blanking. 1 2 3 4 5 Push the cursor key é or ê to highlight 'Blanking' (menu 1). Press ENTER to display the blanking menu. Push the cursor key é or ê to highlight the desired blanking (menu 2) Press ENTER to start up the chosen blanking. Use the cursor keys to adjust the blanking. GEOMETRY BLANKING SHIFT SIZE SIDE KEYSTONE BLANKING ASPECT RATIO [5:4] OPTIONS TOP BOTTOM LEFT RIGHT Select with é or ê then <ENTER> <EXIT> to return. Select with é or ê then <ENTER> <EXIT> to return. RESET menu 2 menu 1 Adjustment of the blanking on the top of the image BLANKING TOP BOTTOM LEFT RIGHT Adjustment of the blanking on the bottom of the image Correct by pushing the cursor key up or down Select with é or ê then <ENTER> <EXIT> to return. Adjustment of the blanking on the left side Adjustment of the blanking on the right side Correct by pushing the cursor key to the right or to the left Aspect Ratio [5:4]/[4:3]/[16:9] Purpose To force the projector in a typical aspect ratio. E.g. projecting a 4:3 image in a 16:9 aspect ratio. How to setup the desired aspect ratio ? 1 2 Push the cursor key é or ê to highlight 'Aspect Ratio' (menu 1). Press ENTER to scroll between [5:4] or [4:3] or [16:9]. GEOMETRY SHIFT SIZE SIDE KEYSTONE BLANKING ASPECT RATIO [5:4] OPTIONS Select with é or ê then <ENTER> <EXIT> to return. menu 1 5976135 BARCOREALITY SIM6 21032000 7-19 Random Access Adjustment Mode Options How to change the geometry options ? 1 2 Push the cursor key é or ê to highlight 'Options' (menu 1). Press ENTER to display the Geometry options menu (menu 2). GEOMETRY GEOMETRY OPTIONS SHIFT SIZE SIDE KEYSTONE BLANKING ASPECT RATIO [5:4] OPTIONS Use the same side keystone correction for all files ? [YES] Select with é or ê then <ENTER> <EXIT> to return. <ENTER> to toggle <EXIT> to return menu 1 menu 2 The next question will be asked by the projector : 'Use the same side keystone correction for all files ? [YES] or [NO]. [YES] : the same keystone correction will be used for all installed files. [NO] : the keystone has to be adjusted file per file. 1 2 Push the ENTER key to toggle between [YES] or [NO]. Press EXIT to return to the Geometry menu. Soft Edge Optional To start up the Soft Edge function 1 2 Push the cursor key é or ê to highlight 'Soft Edge' (menu 1). Press ENTER to select. The soft edge menu will be displayed (menu 2). RANDOM ACCESS ADJUSTMENT MODE SOFT EDGE TYPE SIZE FILE SERVICE PICTURE TUNING AUDIO TUNNING GEOMETRY SOFT EDGE DEMO Select with é or ê then <ENTER> <EXIT> to return. menu 1 Select with é or ê then <ENTER> <EXIT> to return. menu 2 Which soft edge items are available ? - Type : area definition. Size : width of a soft edge area. Type Purpose To select the soft edge area on the screen. How selecting the soft edge area ? 1 2 Push the cursor key é or ê to highlight 'Type' (menu 1). Press ENTER to select. The Type menu will be displayed (menu 2). menu 1 7-20 SOFT EDGE SOFT EDGE TYPE TYPE SIZE NONE LEFT BOTH RIGHT Select with é or ê then <ENTER> <EXIT> to return. Select with é or ê then <ENTER> <EXIT> to return. menu 2 5976135 BARCOREALITY SIM6 21032000 Random Access Adjustment Mode Available soft edge types. None : no soft edge area installed (image 1). Left : soft edge on left side of the image (image 2). Both : soft edge on both sides of the image (image 3). Right : soft edge on right side of the image (image 4). image 1 image 2 image 3 image 4 Size Purpose To change the width of the installed soft area. How to set up the width ? 1 2 Push the cursor key é or ê to highlight 'Size' (menu 1). Press ENTER to select. Use the cursor key ç or è to set up the desired soft edge area width. Range : 1 to 20 (this value is an percentage of the complete image width). SOFT EDGE TYPE SIZE Select with é or ê then <ENTER> <EXIT> to return. menu 1 Important Note : "Black Color" in the Picture tuning menu can be used to match the black parts of the image center to that of the soft edge overlap zones at the right and/or left side of the image. Demo Purpose To have a demonstration of the settings. Available image processing features - Split Screen on/off. How to start up the Demo ? 1 2 Push the cursor key é or ê to highlight 'Demo' (menu 1). Press ENTER to select. The Demo menu will be displayed (menu 2). RANDOM ACCESS ADJUSTMENT MODE DEMO SPLIT SCREEN : ON FILE SERVICE PICTURE TUNING AUDIO TUNNING GEOMETRY SOFT EDGE DEMO Select with é or ê then <ENTER> <EXIT> to return. menu 1 Select with é or ê then <ENTER> <EXIT> to return. menu 2 5976135 BARCOREALITY SIM6 21032000 7-21 Random Access Adjustment Mode Split Screen Purpose To have a demonstration of the image settings such as : sharpness, de-interlacing, color depth and TMR (true motion reproduction). How to start up ? 1 2 Push the cursor key é or ê to highlight 'Split Screen' (menu 1). Press ENTER to toggle between on and off. When on : the screen will split in the middle. One half will stay as the settings are and the other half will change while changing the settings. DEMO SPLIT SCREEN : ON Select with é or ê then <ENTER> <EXIT> to return. menu 1 7-22 5976135 BARCOREALITY SIM6 21032000 Installation Mode 8 INSTALLATION MODE Installation Mode Start Up Push the cursor key é or ê to highlight 'Installation Mode' and then press ENTER. ADJUSTMENT MODE INSTALLATION INPUT SLOTS 800 PERIPHERALS CONFIGURATION OSD COLOR INTERNAL PATTERNS NO SIGNAL LENS MENU POSITION QUICK ACCESS KEYS Select with é or ê then <ENTER> <EXIT> to return. Select a path from below : RANDOM ACCESS INSTALLATION SERVICE Source 01 Select with é or ê then <ENTER> <EXIT> to return. menu 1 menu 2 The following item can be selected in the Installation mode : Input slots : to set up the input priority. 800 Peripheral : to select the type of output module used in the RCVDS05 and the type of communication code, PPM or RC05. Configuration : to set up the projector position. OSD color : to change the color of the highlighted item. Internal Patterns No Signal : background color can be black or blue. Lens : to adjust the lens Menu Position : to force the menu in the middle of the screen. Quick Access Keys : function keys for direct access. Input Slots What can be done ? The input configuration of the variable inputs is shown in the input slots menu. To view or to change the input configuration : 1 2 Push the cursor key é or ê to highlight 'Input Slots'. Press ENTER to select. The internal system will scan the input slots and displays the result in the Input slots menu. The black indicated inputs are selectable and changeable. The gray indicated inputs are fix inputs and are not changeable. The indication in front of the digit means : x : valid signal connected to the input. - : no valid signal connected to the input. INSTALLATION INPUT SLOTS 800 PERIPHERALS CONFIGURATION OSD COLOR INTERNAL PATTERNS NO SIGNAL LENS MENU POSITION QUICK ACCESS KEYS Select with é or ê then <ENTER> <EXIT> to return. menu 1 INPUT SLOTS SLOT SELECTOR [Automatic] x - 1. RGB-SS [CV or HS&VS] 2. RGB-SS [CV or HS&VS] 3. VIDEO 4. S-VIDEO 5. DIGITAL INPUT 6. IEEE 1394 Select with é or ê then <ENTER> <EXIT> to return. menu 2 5976135 BARCOREALITY SIM6 21032000 8-1 Installation Mode Possible results for the input slots : Source indication Video or S-Video Video S-Video RGB analog RGB-CV : separate sync is composite video signal on H/C input RGB-HS&VS : separate sync is horizontal and vertical sync RGB-CS : separate sync is composite sync RGB-SOG : sync on green Component video Component Video What if a switcher is connected to the projector ? If a RCVDS (switched on) or VS05 is connected to the projector, it will be also indicated on the menu by adding +800 peripheral. If no 800 peripheral indication is made on the menu, there are still two possibilities : - no RCVDS or VS05 connected or - RCVDS is switched off. When a 800 peripheral is connected to the projector, the input slots are not accessible with the cursor key to toggle their function. 800 Peripheral What can be installed ? - The type of output module in a RCVDS05. - The type of communication protocol. Defining the Output module of the RCVDS05 When a RCVDS05 is connected to the projector, the type of output module of this RCVDS05 has to be defined in the 800 peripheral menu. The type of output module can be : - standard output module or - 5 cable output module. To define the output module : 1 Push the cursor key é or ê to highlight '800 Peripheral' (menu 1). 2 Press ENTER to select. 3 Push the cursor key é or ê to highlight 'Output module' (menu 2). 4 Press ENTER to toggle between 'Standard' or '5-cable'. INSTALLATION INPUT SLOTS 800 PERIPHERALS CONFIGURATION OSD COLOR INTERNAL PATTERNS NO SIGNAL LENS MENU POSITION QUICK ACCESS KEYS Select with é or ê then <ENTER> <EXIT> to return. menu 1 800 PERIPHERAL OUTPUT MODULE [STANDARD] INFRARED [PPM] Select with é or ê then <ENTER> <EXIT> to return. menu 2 Defining the Infrared Communication protocol When a peripheral is connected to the 'Comm Port', the communication can be in PPM or RC5. The type of communication can be set to : - PPM - RC5 To define the communication : 1 Push the cursor key é or ê to highlight 'Infrared' (menu 1). 2 Press ENTER to select. 3. Press ENTER to toggle between [PPM] or [RC5]. INSTALLATION INPUT SLOTS 800 PERIPHERALS CONFIGURATION OSD COLOR INTERNAL PATTERNS NO SIGNAL LENS MENU POSITION QUICK ACCESS KEYS Select with é or ê then <ENTER> <EXIT> to return. menu 1 8-2 800 PERIPHERAL OUTPUT MODULE [STANDARD] INFRARED [PPM] Select with é or ê then <ENTER> <EXIT> to return. menu 2 5976135 BARCOREALITY SIM6 21032000 Installation Mode Configuration What can be done ? The way of physical installation of the projector can be defined to the projector. The following installation configurations are possible : - front/table - front/ceiling - rear/ceiling - rear/table Set up the Correct Configuration 1 2 Push the cursor key é or ê to highlight 'Configuration' (menu 1). Press ENTER to select. The Configuration menu will be displayed. For more information, see Projector configuration in chapter 3 : 'Installation Guidelines'. INSTALLATION INPUT SLOTS 800 PERIPHERALS CONFIGURATION OSD COLOR INTERNAL PATTERNS NO SIGNAL LENS MENU POSITION QUICK ACCESS KEYS Select with é or ê then <ENTER> <EXIT> to return. menu 1 OSD color (On-Screen Display) What can be done ? The highlighted items on the menus can be displayed in red, green or yellow. How to change this color setting ? 1 2 3 4 Push the cursor key é or ê to highlight 'OSD color'. Press ENTER to select. The OSD color menu will be displayed. Push the cursor key é or ê to highlight a color. Press ENTER to select. INSTALLATION INPUT SLOTS 800 PERIPHERALS CONFIGURATION OSD COLOR INTERNAL PATTERNS NO SIGNAL LENS MENU POSITION QUICK ACCESS KEYS Select with é or ê then <ENTER> <EXIT> to return. menu 1 OSD COLOR HIGHLIGHTED ITEM RED GREEN YELLOW Select with é or ê then <ENTER> <EXIT> to return. menu 2 Internal Patterns What can be done with these internal patterns ? The projector is equipped with different internal patterns which can be used for measurment purposes. 5976135 BARCOREALITY SIM6 21032000 8-3 Installation Mode How to select an internal pattern ? 1 2 3 4 Push the cursor key é or ê to highlight 'Internal Patterns' (menu 1). Press ENTER to select. The internal pattern menu will be displayed (menu 2). Push the cursor key é or ê to highlight the Internal Patterns. Press ENTER to display the select internal pattern. INSTALLATION INPUT SLOTS 800 PERIPHERALS CONFIGURATION OSD COLOR INTERNAL PATTERNS NO SIGNAL LENS MENU POSITION QUICK ACCESS KEYS Select with é or ê then <ENTER> <EXIT> to return. INTERNAL PATTERNS OUTLINE HATCH COLOR BARS MULTIBURST CHECKER BOARD PAGE CHAR ALPHA_NUMERIC CHAR CHARACTER SETS BACKGROUNDS Select with é or ê then <ENTER> <EXIT> to return. menu 2 menu 1 Available patterns Outline Hatch Color Bars Multiburst Checker Board Page Characters Alpha-numeric characters Character Sets Backgrounds No Signal What will happen ? If there is no signal connect to the projector, - the background color can be black or blue and - the projector can shutdown after a certain time. Changing the background color 1 2 3 4 Push the cursor key é or ê to highlight 'No signal'. Press ENTER to select. The 'No Signal' menu will be displayed. Push the cursor key é or ê to highlight 'Color'. Press ENTER to toggle between [blue] or [black]. INSTALLATION INPUT SLOTS 800 PERIPHERALS CONFIGURATION OSD COLOR INTERNAL PATTERNS NO SIGNAL LENS MENU POSITION QUICK ACCESS KEYS Select with é or ê then <ENTER> <EXIT> to return. menu 1 NO SIGNAL COLOR [Blue] SHUTDOWN [Off] Shutdown time : 5 min Select with é or ê then <ENTER> <EXIT> to return. menu 2 Changing the shutdown setting 1 2 3 4 Push the cursor key é or ê to highlight 'No signal'. Press ENTER to select. The 'No Signal' menu will be displayed. Push the cursor key é or ê to highlight 'Shutdown'. Press ENTER to toggle between [On] or [Off]. NO SIGNAL INSTALLATION INPUT SLOTS 800 PERIPHERALS CONFIGURATION OSD COLOR INTERNAL PATTERNS NO SIGNAL LENS MENU POSITION QUICK ACCESS KEYS Select with é or ê then <ENTER> <EXIT> to return. menu 1 8-4 COLOR [Blue] SHUTDOWN [Off] Shutdown time : 5 min Select with é or ê then <ENTER> <EXIT> to return. menu 2 5976135 BARCOREALITY SIM6 21032000 Installation Mode Changing the Shutdown Time The shutdown time can be set between 5 min and 60 min. To set up the shutdown time, handle as follow : 1 Push the cursor key é or ê to highlight 'No signal' (menu 1). 2 Press ENTER to select. 3 Push the cursor key é or ê to highlight 'Shutdown time' (menu 2). 4 Push the cursor key é or ê to change the digits or Enter the digits directly with the digits keys on the RCU. INSTALLATION INPUT SLOTS 800 PERIPHERALS CONFIGURATION OSD COLOR INTERNAL PATTERNS NO SIGNAL LENS MENU POSITION QUICK ACCESS KEYS Select with é or ê then <ENTER> <EXIT> to return. menu 1 NO SIGNAL COLOR [Blue] SHUTDOWN [Off] Shutdown time : 5 min Select with é or ê then <ENTER> <EXIT> to return. menu 2 Quick Access Keys What can be done ? The function keys on top of the RCU can be associated with an adjustment item in one of the adjustment menus. Each item which is not password protected or does not have a key on the RCU can associated to a function key. Getting an overview The menu Quick Access keys gives an overview of the actual programmed functions. To get an overview, handle as follow : 1 Push the cursor key é or ê to highlight 'Quick Access Keys' (menu 1). 2 Press ENTER to select. The Quick Access Keys menu will be displayed (menu 2). INSTALLATION INPUT SLOTS 800 PERIPHERALS CONFIGURATION OSD COLOR INTERNAL PATTERNS NO SIGNAL QUICK ACCESS KEYS LENS MENU POSITION Select with é or ê then <ENTER> <EXIT> to return. menu 1 QUICK ACCESS KEYS F1 : COLOR DEPTH F2 : DIMMING F3 : CONFIGURATION F4 : GAMMA F5 : COLOR TEMPERATURE Note : '?' : auto image adjust '*' : lens adjustments menu 2 Factory preprogrammed keys F1 : color depth F2 : dimming F3 : configuration F4 : gamma F5 : color temperature How to program the quick access keys (function keys) : 1 2 Scroll through the menus until the desired menu is active Push the desired function key for 3 seconds. The message 'Quick access to this menu with Fx', where x is the digit of the selected function key. If the selected menu is not a valid menu for the quick access keys the next message will be displayed : "Quick access to this menu impossible". 5976135 BARCOREALITY SIM6 21032000 8-5 Installation Mode Lens Adjustments What can be done ? All lens adjustments are motorized and can be adjusted with the RCU. The following items can be adjusted: - Zoom/Focus - Shift To adjust all lens functions such as zoom, focus and shift, handle as follow : 1 Push the cursor key é or ê to highlight 'Lens' (menu 1). 2 Press ENTER to select. The Adjustment pattern will be displayed. With the TEXT key it is possible to toggle between the internal adjustment pattern or the connected source. INSTALLATION INPUT SLOTS 800 PERIPHERALS CONFIGURATION OSD COLOR INTERNAL PATTERNS NO SIGNAL QUICK ACCESS KEYS LENS MENU POSITION Select with é or ê then <ENTER> <EXIT> to return. menu 1 Zoom/Focus/Shift The Zoom/Focus function is only applied when a motorised zoom lens is mounted. To focus or zoom the image : 1 2 Push the cursor key é or ê to zoom and ç or è to focus the image (menu 1). When finished, press EXIT to return to the installation menu or press ENTER to go to the shift function. To shift the image : 1 2 3 Press ENTER to switch to the shift menu Push the cursor key é or ê to shift the image up or down and ç or è to shift the image left or right (menu 2). When finished, press EXIT to return to the shift menu or press ENTER to go to the zoom/focus function. The lens can be shifted in a range of : - vertical direction : - 2 mm to + 20 mm - horizontal direction : - 5 mm to + 5 mm Zoom/Focus Change with é,ê,ç,è <ENTER> to Shift <EXIT> to return menu 1 8-6 Shift Change with é,ê,ç,è <ENTER> to Zoom/Focus <EXIT> to return menu 2 5976135 BARCOREALITY SIM6 21032000 Installation Mode Menu Position What can be done ? Menu position can be in the 'Edge' mode where some of the menus will be positionded near the corners of the image, or in the 'Center' mode where all menus will be centered on the image. How to change the setting ? 1 2 Push the cursor key é or ê to highlight 'Menu Position' (menu 1). Press ENTER to toggle between Center and Edges INSTALLATION INPUT SLOTS 800 PERIPHERALS CONFIGURATION OSD COLOR INTERNAL PATTERNS NO SIGNAL LENS MENU POSITION QUICK ACCESS KEYS Select with é or ê then <ENTER> <EXIT> to return. menu 1 5976135 BARCOREALITY SIM6 21032000 8-7 Installation Mode 8-8 5976135 BARCOREALITY SIM6 21032000 Service Mode 9 SERVICE MODE Service Mode Start Up Push the cursor key é or ê to highlight 'Service' and then press ENTER. Some items in the Service mode are password protected (when the password function is active). Enter the password to continue. All other password protected items are now available if you stay in the adjustment mode. ADJUSTMENT MODE SERVICE SERVICE Select a path from below : IDENTIFICATION CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTIME HISTORY DIMMING COMMON ADDRESS : 0 MORE... Select with é or ê then <ENTER> <EXIT> to return. BARCO LOGO PANEL ADJUSTMENTS UNIFORMITY RESET INPUT BALANCE I2C DIAGNOSIS RANDOM ACCESS INSTALLATION SERVICE Select with é or ê then <ENTER> <EXIT> to return. menu 1 menu 2 MORE... Select with é or ê then <ENTER> <EXIT> to return. menu 3 Built-up of the service mode. The service menu is built-up in two parts which are connected together with the 'more' item. If the desired item is not in the list of the displayed menu, select 'more' with the cursor key and push ENTER to display the other items in the service menu. SERVICE IDENTIFICATION CHANGE PASSWORD CHANGE LANGUAGE IDENTIFICATION CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTIME HISTORY DIMMING COMMON ADDRESS : 0 MORE... Select with é or ê then <ENTER> <EXIT> to return. TITLE PAGE SIM OPTIONS Enter new password 0000 ENGLISH Select with é or ê then <ENTER> <EXIT> to return. Select with é or ê then <ENTER> <EXIT> to return. CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUN TIME Projector address : 1 230400 115200 57600 38400 19200 9600 4800 1200 Select with é or ê <ENTER> to accept <EXIT> to return. Enter the serial number of the new lamp 0000000 Select with é or ê then <ENTER> <EXIT> to return. SERVICE BARCO LOGO PANEL ADJUSTMENTS UNIFORMITY PRESET INPUT BALANCE I2C DIAGNOSIS Common address (RC5) : 0 Common address (PPM) : 0 MORE... Select with é or ê then <ENTER> <EXIT> to return. Select with é or ê then <ENTER> <EXIT> to return. Select with è or ç Reprogram with é or ê or numeric keys <ENTER> to confirm <EXIT> to return LAMP RUNTIME HISTORY DIMMING Serial No Runtime ----------------------------------------------------> 0111121 600 h 0110031 990 h 0110010 1000 h 0000000 0h 0000000 0h 0000000 0h 0000000 0h ----------------------------------------------------<EXIT> to return 5976069 BARCOREALITY SIM6 21032000 9-1 Service Mode SERVICE PANEL ADJUSTMENT PRESET INPUT BALANCE UNIFORMITY IDENTIFICATION CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTINE HISTORY DIMMING MORE... Select the color temperature WHITE BALANCE BLACK BALANCE PROJECTOR WHITE 6500 DEFAULT ADJUST GRAY ADJUST WHITE ADJUST BLACK PURITY DEFAULT INITIALIZE B/W Select with é or ê then press ENTER Select with é or ê then <ENTER> <EXIT> to return. Select with é or ê then <ENTER> <EXIT> to return. SERVICE BARCO LOGO BARCO LOGO PANEL ADJUSTMENTS UNIFORMITY PRESET INPUT BALANCE I2C DIAGNOSIS STATUS : [ON] BACKGROUND : [ON] SHIFT HOT KEY : [TEXT] MORE... Select with é or ê <ENTER> to toggle/select <EXIT> to return. Select with é or ê then <ENTER> <EXIT> to return. Select with é or ê then <ENTER> <EXIT> to return. I2C DIAGNOSIS DECODER INPUT SELECT AUDIO MOTOR DRIVER LAMP DRIVER LCD DRIVER LCD DRIVER LCD DRIVER LCD DRIVER 12H 16H 18H 74H 78H C0H C4H C8H CCH DCA ### ### ### ### ### ### ### ### ### Identification What can be seen ? The identification is split up in two different items, title page and Sim options. The Title page shows the general information of the projector. The Sim options shows the status of the options. Start Up 1 2 Push the cursor key é or ê to highlight 'Identification' (menu 1). Press ENTER to display the Identification menu (menu 2). SERVICE IDENTIFICATION IDENTIFICATION CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTINE HISTORY DIMMING MORE... TITLE PAGE SIM OPTIONS Select with é or ê then <ENTER> <EXIT> to return. Select with é or ê then <ENTER> <EXIT> to return. menu 1 menu 2 Available items Title page Sim options Title Page What will be indicated on the title page ? The following indication are given on the title page : - type of projector - projector address - software version - installation configuration - baud rate - text ON - projector serial number - projector run time 9-2 5976135 BARCOREALITY SIM6 21032000 Service Mode Start Up 1 2 Push the cursor key é or ê to highlight 'Title Page' (menu 1). Press Enter to select. The Title page will be displayed. BARCO REALITY SIM6 IDENTIFICATION TITLE PAGE SIM OPTIONS Proj. address : 001 Soft. version : 1.0 Config : front/ ceiling Baudrate PC : 9600 text : ON Serial no.: 1010200 Run time : 100 h Select with é or ê then <ENTER> <EXIT> to return. menu 1 Select with é or ê then <ENTER> <EXIT> to return. menu 2 Available items - - type of projector : BARCOREALITY SIM6 software version Proj. Address : to change the address of the projector, see Change Projector Address in this chapter. Installation : possible installations : * Front/Ceiling * Front/Table * Rear/Ceiling * Rear/Table To change the installation configuration follow the instructions in chapter Installation Guidelines. Baud rate : transfer speed for communication with an IBM PC (or compatible) or MAC. The baud rate of the projector must be the same as the baud rate of the connected computer. When there is a difference, consult 'Change Baudrate PC' in this chapter. Projector Run Time : gives the total run time since the first start up. All projectors leave the factory with a run time of approximately 24 hours. Projector Serial number : indicates the fabrication number of the projector. This number can be useful when calling for technical assistance. SIM Options What will be indicate ? This menu will indicate if the SIM options are installed or not. Start Up 1 2 Push the cursor key é or ê to highlight 'SIM Options' (menu 1). Press Enter to select. The SIM options screen will be displayed (menu 2). IDENTIFICATION SIM OPTIONS TITLE PAGE SIM OPTIONS SOFT EDGE: ON TDR : ON TMR : ON UNIFORMITY : ON MOT. DIMMING : ON Select with é or ê then <ENTER> <EXIT> to return. menu 1 <EXIT> to return. menu 2 Available SIM options - Soft Edge TDR : transportation delay reduction TMR : true motion reproduction Uniformity Motorized Dimming 5976069 BARCOREALITY SIM6 21032000 9-3 Service Mode Change Password How to enable or disable the password function ? This item is password protected when the password strap is installed. The password function is enabled when the password strap on the controller module is installed. Consult an authorised Barco service technician to change the strap position. How to change the password ? 1 2 3 Push the cursor key é or ê to highlight 'Change password' (menu 1). Press ENTER to display the Change Password menu (menu 2). The old password is displayed and can be changed by entering the digit with the numeric keys of the RCU or local keypad. Press ENTER to save the new entered password. Press EXIT if no changes have to be made. SERVICE CHANGE PASSWORD IDENTIFICATION CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTIME HISTORY DIMMING MORE... Enter new password 0000 Select with é or ê then <ENTER> <EXIT> to return. Select with é or ê then <ENTER> <EXIT> to return. menu 2 menu 1 Change Language Start Up 1 2 3 4 Push the cursor key é or ê to highlight 'Change Language' (menu 1). Press ENTER to display the Change Language menu (menu 2). Push the cursor key é or ê to highlight the desired language. Press ENTER to change the language. Available languages : English SERVICE CHANGE LANGUAGE IDENTIFICATION CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTINE HISTORY DIMMING MORE ... Select with é or ê then <ENTER> <EXIT> to return. English Select with é or ê then <ENTER> <EXIT> to return. menu 2 menu 1 Change Projector Address What can be changed ? Within the 'Change Projector Address' item, the follow items can be changed : - Projector address - Common address 9-4 5976135 BARCOREALITY SIM6 21032000 Service Mode Start up 1 2 Push the cursor key é or ê to highlight 'Change Projector Address'' (menu 1). Press ENTER to select. The Change Projector Address menu will be displayed. SERVICE IDENTIFICATION CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTINE HISTORY DIMMING MORE ... Select with é or ê then <ENTER> <EXIT> to return. CHANGE PROJ. ADDRESS Projector address : 1 Common address (RC5) : 0 Common address (PPM) : 0 Select with é or ê then <ENTER> <EXIT> to return. menu 2 menu 1 Projector Address How to change that address ? 1 2 Push the cursor key é or ê to highlight 'Projector Address'' (menu 1). Press ENTER to select. The actual address is filled in. The first digit is highlighted. CHANGE PROJ. ADDRESS Projector address : 1 Common address (RC5) : 0 Common address (PPM) : 0 Select with é or ê then <ENTER> <EXIT> to return. menu 1 Entering the new projector address - with the digit keys on the RCU or the local keypad or push the cursor key ç or è to select a digit and change the value by pushing the cursor key é or ê until the new value is reached. Continue with the other digits on the same way. Common Address How to change that common address ? 1 2 Push the cursor key é or ê to highlight the active 'Common Address'' (menu 1). Press ENTER to select. CHANGE PROJ. ADDRESS Projector address : 1 Common address (RC5) : 0 Common address (PPM) : 0 Select with é or ê then <ENTER> <EXIT> to return. menu 1 Entering the new common address Only addresses between 0 and 1 are valid. - with the digit keys on the RCU or the local keypad or - pushing the cursor key é or ê until the new value is reached. 5976069 BARCOREALITY SIM6 21032000 9-5 Service Mode Change Baudrate PC Start Up 1 2 3 4 Push the cursor key é or ê to highlight 'Change Baudrate PC'' (menu 1). Press ENTER to display the Change Baudrate PC menu. The actual baudrate will be highlighed. The following baud rates are available : 230400/115200/57600/38400/19200/9600/4800/1200 Push the cursor key é or ê to highlight the desired baudrate. Press ENTER to select. SERVICE CHANGE BAUDRATE PC IDENTIFICATION CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTIME HISTORY DIMMING MORE... 230400 115200 57600 38400 19200 9600 4800 1200 Select with é or ê then <ENTER> <EXIT> to return. Select with é or ê then <ENTER> <EXIT> to return. menu 1 menu 1 Reset Lamp Runtime When is it allowed ? Reset lamp run time is only allowed when a new lamp is installed. Start Up 1 2 Push the cursor key é or ê to highlight 'Reset Lamp Run Time'' (menu 1). Press ENTER. The following warning will be displayed (menu 2): Risk of electrical shock. Reset lamp run time is reserved to qualified service personnel. If you are not qualified, press EXIT to cancel the reset operation. SERVICE WARNING IDENTIFICATION CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTIME HISTORY DIMMING MORE... ----------------------------------------------------RISK OF ELECTRICAL SHOCK ______________________________________________________________ RESET LAMP RUN TIME is reserved to qualified service personnel Select with é or ê then <ENTER> <EXIT> to return. <ENTER> to accept <EXIT> to return. menu 2 menu 1 Lamp Run Time History What can be done ? Getting an overview of the different lamp run times 9-6 5976135 BARCOREALITY SIM6 21032000 Service Mode Start Up 1 2 3 Push the cursor key é or ê to highlight 'Lamp Run Time History' (menu 1). Press ENTER to display the Lamp Run Time overview (menu 2). A listing with the lamp serial number and the corresponding run time will be displayed. The actual installed lamp will be marked. Press EXIT to return to the service mode selection menu. SERVICE IDENTIFICATION CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTIME HISTORY DIMMING MORE... LAMP RUNTIME HISTORY Serial No Runtime ----------------------------------------------------> 0111121 600 h 0110031 980 h 0110010 1000 h 0000000 0h 0000000 0h 0000000 0h ----------------------------------------------------- Select with é or ê then <ENTER> <EXIT> to return. <ENTER> for detail <EXIT> to return menu 1 menu 1 Dimming What can be done ? The lamp can be dimmed via the lamp dimming feature or via the optional motorized dimming. Start Up 1 2 Push the cursor key é or ê to highlight 'Dimming' (menu 1). Press ENTER to select. The dimming menu will be displayed (menu 2). SERVICE DIMMING IDENTIFICATION CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTIME HISTORY DIMMING MORE... LAMP DIMMING MOTORIZED DIMMING Select with é or ê then <ENTER> <EXIT> to return. Select with é or ê then <ENTER> <EXIT> to return. menu 1 menu 2 Lamp Dimming Start Up 1 2 3 Push the cursor key é or ê to highlight 'Lamp Dimming' (menu 1). Press ENTER to start up the lamp dimming. Push the cursor key ç or è to dim the lamp. Remark : The projector starts always with full lamp power. DIMMING LAMP DIMMING MOTORIZED DIMMING Select with é or ê then <ENTER> <EXIT> to return. menu 1 5976069 BARCOREALITY SIM6 21032000 9-7 Service Mode Motorized Dimming Optional Start Up 1 2 3 4 Push the cursor key é or ê to highlight 'Motorized Dimming' (menu 1). Press ENTER to start up the motorized dimming. Use the cursor keys to change the dimming factor or Press ENTER and type in a dimming factor with the digit keys on the RCU and press ENTER again. Range 3..100 Default : 100 DIMMING LAMP DIMMING MOTORIZED DIMMING Select with é or ê then <ENTER> <EXIT> to return. menu 1 BARCO logo What can be done ? The BARCO logo can be added to the image, in overlay or on a background, on any place on the screen. How to add the BARCO logo or to change a setting ? 1 2 Push the cursor key é or ê to highlight 'BARCO logo'' (menu 1). Press ENTER to select. The BARCO logo menu will be displayed (menu 2) . The actual settings will be displayed. Within this menu, three toggle settings and a shift control are available. SERVICE BARCO LOGO BARCO LOGO PANEL ADJUSTMENTS UNIFORMITY PRESET INPUT BALANCE I2C DIAGNOSIS STATUS : [ON] BACKGROUND : [ON] SHIFT HOT KEY : [TEXT] MORE... Select with é or ê then <ENTER> <EXIT> to return. Select with é or ê then <ENTER> <EXIT> to return. menu 2 menu 1 Available settings STATUS [ON/OFF] ON : BARCO logo will be displayed on the screen. OFF : No BARCO logo displayed on the screen. BACKGROUND [ON/OFF] ON : BARCO logo will be displayed on a black background. OFF : BARCO logo will be displayed without any background. SHIFT By pushing the cursor key é, ê, ç or è, the BARCO logo can be positioned anywhere on the screen. HOT KEY [TEXT/OFF] OFF : no key on the RCU is used to display the BARCO logo. TEXT : the TEXT key on the RCU is used to display or to remove the BARCO logo with one single push on this key (only in operational mode). 9-8 5976135 BARCOREALITY SIM6 21032000 Service Mode Panel Adjustments Warning Changing these settings may seriously affect the performance of the projector. All panel adjustments are factory adjusted. If not really necessary, do not touch any of these adjustments. They are useful when a new panel is installed. Start Up 1 2 Push the cursor key é or ê to highlight 'Panel Adjustments'' (menu 1). Press ENTER to select. The following warning will be displayed : Panel Adjustments is reserved to qualified service personnel. If you are not qualified, press EXIT to cancel the panel adjustments. SERVICE BARCO LOGO PANEL ADJUSTMENTS UNIFORMITY PRESET INPUT BALANCE I2C DIAGNOSIS MORE... Select with é or ê then <ENTER> <EXIT> to return. WARNING PRESET INPUT BALANCE is reserved to qualified service personnel <ENTER> to accept <EXIT> to return. menu 2 menu 1 Uniformity Warning Changing these settings may seriously affect the performance of the projector. Start Up 1 2 Push the cursor key é or ê to highlight "Uniformity'' (menu 1). Press ENTER to select. The following warning will be displayed : Uniformity is reserved to qualified service personnel. If you are not qualified, press EXIT to cancel the uniformity. SERVICE WARNING BARCO LOGO PANEL ADJUSTMENTS UNIFORMITY PRESET INPUT BALANCE I2C DIAGNOSIS UNIFORMITY is reserved to qualified service personnel MORE... Select with é or ê then <ENTER> <EXIT> to return. <ENTER> to accept <EXIT> to return. menu 2 menu 1 5976069 BARCOREALITY SIM6 21032000 9-9 Service Mode Preset Input Balance Warning Changing these settings may seriously affect the performance of the projector. Start Up 1 2 Push the cursor key é or ê to highlight "Preset Input Balance'' (menu 1). Press ENTER to select. The following warning will be displayed : Preset Input Balance is reserved to qualified service personnel. If you are not qualified, press EXIT to cancel the preset input balance. SERVICE WARNING BARCO LOGO PANEL ADJUSTMENTS UNIFORMITY PRESET INPUT BALANCE I2C DIAGNOSIS PRESET INPUT BALANCE is reserved to qualified service personnel MORE... Select with é or ê then <ENTER> <EXIT> to return. <ENTER> to accept <EXIT> to return. menu 2 menu 1 I2C diagnosis. What can be done ? Gives an overview of the correct working of the I²C controlled IC's. I2C DIAGNOSIS SERVICE BARCO LOGO PANEL ADJUSTMENTS UNIFORMITY PRESET INPUT BALANCE I2C DIAGNOSIS MORE... Select with é or ê then <ENTER> <EXIT> to return. menu 1 9-10 DECODER INPUT SELECT AUDIO MOTOR DRIVER LAMP DRIVER LCD DRIVER LCD DRIVER LCD DRIVER LCD DRIVER 12H 16H 18H 74H 78H C0H C4H C8H CHH DCA ### ### ### ### ### ### ### ### ### <EXIT> TO RETURN menu 2 5976135 BARCOREALITY SIM6 21032000 Appendix A : Standard Source Set Up Files A STANDARD SOURCE SET UP FILES name resolution Fvert Hz 1600_48V 1600 X 600i 1600_60V Fhor kHz pact ltot lact 48,040 62,500 135,000 2160 1600 651 600 1600 X 1200 60,000 75,000 162,000 2160 1600 1250 1200 1600_65V 1600 X 1200 65,000 81,250 175,500 2160 1600 1250 1200 1600_70V 1600 X 1200 70,000 87,500 189,000 2160 1600 1250 1200 8514_a 1024 x 384i 43,479 35,522 44,900 1264 1024 409 384 FHOR kHz : horizontal frequency of the source. cga 640 x 200 59,924 15,700 14,318 912 640 262 200 FPIX MHz : pixel frequency compusc4 1024 x 480i 29,945 30,694 39,779 1296 1024 512 480 PTOT : total pixels on one horizontal line ed 735 x 480 59,943 31,470 28,638 910 735 525 480 PACT : active pixels on one horizontal line ega 640 x 350 59,702 21,851 16,257 744 640 366 350 LTOT : total lines in one field ews_50 1280 x 1024 50,000 52,350 87,948 1680 1280 1047 1024 LACT : active lines in one field ews_60 1280 x 1024 60,000 63,900 107,352 1680 1280 1065 1024 ews_60v 1280 x 1024 60,282 63,657 110,000 1728 1280 1056 1024 ews_72 1280 x 1024 72,000 76,968 130,076 1690 1280 1069 1024 ews_75 1280 x 1024 75,025 79,976 135,000 1688 1280 1066 1024 ews_85 1024 x 1280 85,024 91,146 157,500 1728 1280 1072 1024 ews_100 1024 x 1280 100,139 107,350185,5 1280 1072 1024 fmr 640 x 400i 42,323 36,440 28,570 784 640 431 400 fmto_2 640 x 400 55,370 24,370 21,056 864 640 440 400 HD_1080i(*) 1920 x 540i 30,000 33,750 74,250 2200 1920 562 540 hd720p(*) 1280 x 720 60,000 45,000 74,250 1650 1200 750 720 hdmac(*) 1252 x 570i 25,020 31,250 39,125 1252 1024 625 570 inter_gr 1184 x 886 67,170 61,796 92,941 1504 1184 920 886 mac_2 640 x 480 66,667 35,000 30,240 864 640 525 480 mac_3 512 x 384 60,147 24,480 15,667 640 512 407 384 mac_4 560 x 384 60,147 24,480 17,234 704 560 407 384 mac_5 512 x 342 60,158 22,259 15,670 704 512 370 342 mac_6 832 x 624 74,546 49,722 57,280 1152 832 667 624 MAC_7 1024 x 768 74,907 60,150 80,000 1330 1024 803 768 mac_lc 640 x 480 66,619 34,975 31,338 896 640 525 480 mac_por 640 x 870 74,996 68,846 57,280 832 640 918 870 muse(*) 1172 x 518i 30,000 33,750 37,125 1172 1024 563 518 mxga_60 1152 x 864 60,000 54,540 79,410 1456 1152 909 864 5976135 BARCOREALITY SIM6 21032000 Fpix MHz ptot 1728 Name : name of file, contains the settings Resolution : image resolution, when followed by ...I means interlaced. FVERT Hz : vertical frame frequency of the source A-1 Appendix A : Standard Source Set Up Files A-2 name resolution Fvert Hz mxga_70 1152 x 864 mxga_75 Fhor kHz Fpix MHz ptot pact ltot lact 70,012 63,851 94,500 1480 1152 912 864 1152 x 864 75,000 67,500 108,000 1600 1152 900 864 mxga_80 1152 x 864 80,000 76,640 110,362 1440 1152 958 864 mxga_85 1152 x 864 84,999 77,094 121,500 1576 1152 907 864 mxga_100 1152 x 864 100,000 93,000 145,824 1568 1152 930 864 Video525(*) 1302 x 239i 29,970 15,734 32,207 1302 1024 263 239 Video625(*) 1024 x 278i 25,000 15,625 31,984 1310 1024 313 278 pam500 640 x 400 60,000 26,400 22,810 864 640 440 400 pam800 1120 x 375i 44,936 36,443 50,000 1372 1120 406 375 pc98_1 640 x 400 56,416 24,823 21,050 848 640 440 400 pc98_2 1120 x 375i 39,994 32,835 47,840 1457 1120 411 375 pc98_3 1120 x 750 60,000 50,000 78,569 1571 1120 833 750 s1152_66 1152 x 900 66,004 61,846 94,500 1528 1152 937 900 s1152_76 1152 x 900 76,637 71,809 108,000 1504 1152 937 900 SDI_625(*) 675 x 2781 25,000 15,625 13,500 864 720 313 278 SDI_525(*) 675 x 2401 29,970 15,734 13,500 858 720 263 240 sg_50 1600 x 1200 50,000 62,500 130,313 2085 1600 1250 1200 sg_60_1 1280 x 1024 60,000 63.900 107,352 1680 1280 1065 1024 sg_60_2 1024 x 768 60,000 48.780 64,390 1320 1024 813 768 sg_60_3 960 x 680 60,000 43,200 54,432 1260 960 720 680 sg_60_4 1600 x 1200 60,000 75,000 156,375 2085 1600 1250 1200 sunews67 1280 x 1024 67,189 71,691 117,000 1632 1280 1067 1024 sunews76 1280 x 1024 76,107 81,130 135,000 1664 1280 1066 1024 sunxga60 1024 x 768 59,984 48,287 64,125 1328 1024 805 768 sunxga70 1024 x 768 70,041 56,596 74,250 1312 1024 808 768 sunxga77 1024 x 768 77,069 62,040 84,375 1360 1024 805 768 sup_mac 1024 x 768 60,000 48,780 63,999 1312 1024 813 768 svga_56v 800 x 600 56,250 35,156 36,000 1024 800 625 600 svga_60v 800 x 600 60,317 37,879 40,000 1056 800 628 600 svga_72v 800 x 600 72,084 48,080 50,003 1040 800 667 600 svga_75 800 x 600 75,000 46,875 49,500 1056 800 625 600 svga_85 800 x 600 85,061 53,674 56,250 1048 800 631 600 svga_100 800 x 600 100,27662,973 66,500 1056 800 628 600 vga_72v 640 x 480 72,800 37,856 31,496 832 640 520 480 vga_75 640 x 480 75,000 37,500 31,500 840 640 500 480 vga_85 640 x 480 85,008 43,269 36,000 832 640 509 480 5976135 BARCOREALITY SIM6 21032000 Appendix A : Standard Source Set Up Files name resolution Fvert Hz vga_100 640 x 480 vga_gr pact ltot lact 100,000 52,500 44,520 848 640 525 480 640 x 480 59,941 31,469 25,175 800 640 525 480 vga_txt 720 x 400 70,087 31,469 28,322 900 720 449 400 vga75iso 640 x 480 75,000 39,375 31,500 800 640 525 480 xga_60 1024 x 768 60,000 48,360 64,996 1344 1024 806 768 xga_70 1024 x 768 70,000 57,050 78,044 1368 1024 815 768 xga_70v 1024 x 768 69,705 56,182 74,610 1328 1024 806 768 xga_72 1024 x 768 71,955 58,140 80,000 1376 1024 808 768 xga_75 1024 x 768 75,781 61,080 86,000 1408 1024 806 768 xga75_gs 1024 x 768 74,534 59,701 79,284 1328 1024 801 768 xga_85 1024 x 768 84,997 68,677 94,500 1376 1024 808 768 xga_100 1024 x 768 100,000 80,800 110,534 1368 1024 808 768 5976135 BARCOREALITY SIM6 21032000 Fhor kHz Fpix MHz ptot A-3 Appendix A : Standard Source Set Up Files A-4 5976135 BARCOREALITY SIM6 21032000 Source Numbers 80 - 89 and 90 - 99 B SOURCE NUMBERS 81 - 86 AND 91 - 96 Projector without any 800 peripheral connected. The source numbers 81 - 86 and 91 - 96 do not correspond to physical inputs. An additional adjustment file can be created for these source numbers. This file can contain different settings. The relationship between sources 1 - 6 and 91 - 96 or between 1 - 6 and 81 - 86 is shown in the diagram below. source input 1 source input 2 file A file A' file A'' source number 2 source number 82 source number 92 file B file B' file B'' source number 3 source number 83 source number 93 file C file C' file C'' ○ ○ source input 3 source number 1 source number 81 source number 91 source input 6 source number 6 source number 86 source number 96 file F file F' file F'' Follow the steps below to create a second or a third file for sources 1 to 6 : 1. 2. 3. 4. Select the source between 1 and 6. Select the corresponding source number between 81 and 86 or 91 and 96 with the digit keys on the RCU. Enter the adjustment mode and load a corresponding file. Edit this file if necessary. Save the file and exit the adjustment mode. Projector with a 800 peripheral connected. Source numbers 91 - 99. The source numbers 91 - 99 do not correspond to physical inputs. An additional adjustment file can be created for these source numbers (source numbers of the 800 peripheral). This file can contain different settings. The relationship between sources 1 - 9 of the 800 peripheral and 91 - 99 is shown in the diagram below. source number 1 source number 91 file A file A' source input 2 source number 2 source number 92 file B file B' source input 3 source number 3 source number 93 file C file C' source input 9 source number 9 source number 99 ○ ○ source input 1 file I file I' Follow the same procedure as for a projector without a 800 peripheral connected. 5976135 BARCOREALITY SIM6 21032000 B-1 Source Numbers 80 - 89 and 90 - 99 Source numbers 81 - 86 Only valid if no input module is connected to slot 81 - 86 of a RCVDS05. The source numbers 81 - 86 correspond to the physical inputs 1 - 6 of the projector. e.g. When slot 1 of the projector has to be selected, key in source number 81. The relationship between the sources of slot 1 - 6 of the projector with 800 peripheral is shown in the table below. source source source source source source B-2 of of of of of of slot slot slot slot slot slot 1 2 3 4 5 6 source source source source source source number number number number number number 81 82 83 84 85 86 5976135 BARCOREALITY SIM6 21032000
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project