User`s manual | Atmel ATA6831 Network Card User Manual

User’s manual
E5802B/E5833B/
E1802B/E1833B
5.8 GHz cordless
telephone with caller
ID/call waiting
Congratulations
on purchasing your
new AT&T product.
Before using this AT&T product, please
read the Important safety instructions
on pages 41-43 of this manual.
Please thoroughly read the user’s
manual for all the feature operations
and troubleshooting information necessary to install
and operate your new
AT&T product. You can also visit our
website at www.telephones.att.com
or call 1 (800) 222-3111.
In Canada dial 1(866) 288-4268.
Model #:
E5802B/E5833B/E1802B/E1833B
Product name:
5.8GHz cordless telephone
Serial #:
(found on the bottom of the telephone base)
Purchase date:
Place of purchase:
© 2007 Advanced American Telephones. All rights reserved.
AT&T and the AT&T logo are trademarks of AT&T Knowledge Ventures,
licensed to Advanced American Telephones.
You must install and charge
the battery before using the
telephone.
STOP!
See page 7
for easy instructions.
For customer service or product information, visit our website
at www.telephones.att.com or call 1 (800) 222-3111.
In Canada dial 1 (866) 288-4268.
CAUTION: To reduce the risk of fire or injury to persons or damage to the telephone, read
and follow these instructions carefully:
• Use only the supplied rechargeable battery or replacement battery 2422 (SKU 23402, part number
89-0047-00-00) or equivalent. To order a replacement battery, visit our
website at www.telephones.att.com or call 1 (800) 222-3111.
In Canada dial 1 (866) 288-4268.
• Do not dispose of the battery in a fire. Like other batteries of this type, it could explode if burned. Check
with local codes for special disposal instructions.
• Do not open or mutilate the battery. Released electrolyte is corrosive and may cause damage to the
eyes or skin. It may be toxic if swallowed.
• Exercise care in handling batteries in order not to create a short circuit. Do not allow conductive materials such as rings, bracelets, or keys to touch the battery. The battery or conductor may overheat and
cause harm.
• Charge the battery provided with or identified for use with this product only in accordance with the
instructions and limitations specified in this manual.
• Observe proper polarity orientation between the battery and battery charger.
• Do not disassemble your telephone. There are no user-serviceable parts inside. Refer to qualified service personnel for servicing.
User’s manual
E5802B/E5833B/
E1802B/E1833B
5.8 GHz cordless
telephone with caller
ID/call waiting
Table of contents
Getting started
Caller ID summary
Quick reference guide.........................2
Caller ID summary ..............................26
Parts checklist .........................................4
To review the call summary .........29
Telephone base installation .............5
Delete call summary entries ........30
Battery installation & charging ......7
Add entries to the directory .........31
Installation options ...............................8
Appendix
Belt clip & optional headset.........10
Screen icons, indicator lights
& tones ................................................32
Telephone operation
Handset display screen messages......33
Settings ....................................................11
Troubleshooting...................................35
Basic operation ....................................14
Important safety instructions .......41
Options while on calls .....................17
FCC Part 68 & ACTA..........................44
Call transfer for E5802B/E1802B ...18
FCC Part 15............................................46
Call transfer for E5833B/E1833B ...19
Limited warranty .................................47
Technical specifications ..................50
Directory
Index ..........................................................51
Directory ..................................................20
Speed dial ...............................................21
New directory entries.......................22
Directory search ..................................24
To change or dial entries ...............25
1
Getting started
Quick reference guide
Cordless handset
CID/-VOLUME
DIR
While in a menu, press to scoll
down. When in idle mode, press
to display call summary entries
(page 29). While entering names
or numbers, press to move the
cursor to the left. During a call,
press CID to decrease listening
volume.
/VOLUME+
While in a menu, press to scoll
up. When in idle mode, press to
display directory entries (page 24).
While entering names, press to
advance the cursor. During a call,
press DIR
to increase listening
volume.
OFF/CLEAR
PHONE/FLASH
During a call, press to hang up.
While using menus, press to cancel an operation, or exit the menu
(page 12).
Press to make or answer a call.
During a call, press to receive
an incoming call if call waiting is
activated (page 17).
CHAN/DELETE
MENU/SEL/TRANSFER
When on a call, press CHAN/DELETE
to scan for a clearer channel
when there is static or interference on the line (page 17).
When in caller ID mode, press
to delete the displayed caller
ID entry (page 30), or press
and hold to delete all caller ID
entries (page 30).
Press to display menu. Press to
store a programming option. During
a call, press to transfer a call
between handsets (pages 18-19).
MUTE
While on a call, press to mute
microphone. Press again to resume
(page 17).
SPEAKER
REDIAL/PAUSE
Press to activate handset speakerphone. Press again to resume
normal handset use (page 14).
While in idle mode, press to display
last number called (page 15). While
dialing or entering numbers to the
directory, press to insert a four-second dialing pause (page 23).
Feature menu
DIRECTORY
Feature menu
Using menus
DIRECTORY .............. Page
SPEED DIAL ............. Page
RINGER ......................Page
DATE/TIME ............... Page
DIAL MODE .............. Page
CLR VOICE MAIL .... Page
LANGUAGE .............. Page
2
20
21
12
12
11
13
11
Press CID or DIR
menu items.
to scroll through
Press MENU/SEL to select or modify a
highlighted item.
Press OFF/CLEAR to cancel an operation,
or exit the menu display.
Getting started
Quick reference guide
Telephone base
VOICEMAIL
Flashes when there is new voicemail
(requires voicemail service from your
local telephone company).
CHARGE/IN USE
HANDSET LOCATOR
•
On when the cordless handset is properly
positioned to charge in the telephone base.
•
•
Flashes quickly while an incoming call is ringing.
Flashes when one of the handsets is in use.
3
Press to make handsets beep when
there is no handset on the telephone
base (page 16).
Getting started
Parts checklist
Save your sales receipt and original packaging in case you need to ship your
telephone for warranty service.
Check to make sure the telephone package includes the following. The model
number of your telephone can be found on the label located on the bottom
of the telephone base.
User’s manual
Quick start guide
E5802B/E5833B/
E1802B/E1833B
5.8 GHz cordless
telephone with caller
ID/call waiting
E5802B/E5833B/
E1802B/E1833B
5.8 GHz cordless
telephone with caller
ID/call waiting
User's manual
Quick start guide
Charger for cordless handset
(1 for E5802B/1802B)
(2 for E5833B/1833B)
Power adapter for
telephone base
Cordless handset
(2 for E5802B/1802B)
(3 for E5833B/1833B)
Battery for cordless handset
(2 for E5802B/1802B)
(3 for E5833B/1833B)
Telephone base
Battery compartment door
(2 for E5802B/1802B)
(3 for E5833B/1833B)
Belt clip for cordless Telephone line cord
handset
(2 for E5802B/1802B)
(3 for E5833B/1833B)
Power adapter for handset
charger
(1 for E5802B/1802B)
(2 for E5833B/1833B)
4
Getting started
Telephone base installation
Choose a central location close to a telephone jack and a power outlet not
connected to a wall switch. The telephone base can be placed on a flat surface or mounted on a standard wall plate. For optimum range and better
reception, place the telephone base in a high and open location.
Avoid placing the telephone base too close to:
• Communication devices such as: personal computers, computer routers,
television sets, VCRs, wireless routers (wireless broadband, wi-fi, or 802.11)
or other cordless telephones.
• Excessive heat sources.
• Noise sources such as a window with traffic outside, motors, microwave
ovens, refrigerators, or fluorescent lighting.
• Excessive dust sources such as a workshop or garage.
• Excessive moisture.
• Extremely low temperature.
• Mechanical vibration or shock such as on top of the washing machine or
work bench.
5
Getting started
Telephone base installation
1. Plug the small end of
the larger power adapter
into the power jack at
the bottom of the telephone base.
2. Plug one end of the
telephone line cord into
the telephone jack at the
bottom of the telephone
base.
3. Route cords through
slots.
5. Plug the other end
of the telephone line
cord into a telephone
jack.
4. Plug the large end of
the larger power adapter
into an electrical outlet
not controlled by a wall
switch.
Telephone line cord
DSL filter
(Optional for DSL users,
see number four in the
note section, below.)
NOTES:
To order a replacement power adapter, visit our website at www.telephones.att.com
or call 1 (800) 222-3111. In Canada dial 1 (866) 288-4268.
1. Use only the power adapter supplied with this product or equivalent.
2. Be sure to use an electrical outlet not controlled by a wall switch.
3. This power adapter is intended to be correctly oriented in a vertical or floor mount position.
4. If you receive high speed internet through your telephone line (commonly referred to as DSL), and
you are experiencing interference during telephone conversations and/or your caller ID features
are not functioning properly, install a DSL filter to the telephone line between the telephone base
and the telephone wall jack. Contact your DSL service provider for a DSL filter.
6
Getting started
Battery installation & charging
After installing the battery, you may be able to make or receive short calls. For
best performance, place the handsets in the telephone base or charger to charge
for 16 hours before use.
You can keep the battery charged by returning the handsets to the telephone
base or the charger after use. When the battery is fully depleted, a recharge takes
about 12 hours. The average talk time on a fully charged battery is about five
hours, and the standby time is approximately six days. Actual battery life depends
on usage conditions and age of battery.
1. Plug the small end of
the smaller power adapter
into the jack on the underside of the charger, then
route the cord through the
slot as shown.
2. Plug the large
end of the smaller
power adapter into
an electrical outlet
not controlled by a
wall switch.
3. Insert the plug as indicated. Be sure to securely insert
the plug, making sure that it
matches the color-coded label
inside the battery compartment.
6. You may be able to make or receive
short calls. For best performance, place
the handset in the telephone base or
charger to charge for at least 16 hours
before first use.
BATTERY LOW
-- 1 -10:08AM
NEEDS RECHARGING
then
02/14
Battery low indicator
Return the handset to the
telephone base or charger to
recharge when this symbol
flashes and the handset beeps
or when the handset screen
displays NEEDS RECHARGING.
4. Place the battery and wires
inside the compartment.
5. Slide the battery compartment cover up
until it clicks.
To replace the battery,
press in and downward
on the tab of the battery compartment to
open the battery compartment cover. Lift
out the old battery
and disconnect it from
the handset. Follow
the instructions on
this page to install and
charge the new battery.
NOTE: Under normal conditions, the
battery should last around one year. This
may vary depending on usage.
Caution: Use only the supplied rechargeable battery, replacement battery 2422 (SKU 23402, part
number 89-0047-00-00) or equivalent. To order a replacement battery, visit our
website at www.telephones.att.com or call 1 (800) 222-3111. In
Canada dial 1 (866) 288-4268.
7
Getting started
Installation options
NOTE: The mounting bracket must be used for both tabletop use and wall mounting positions.
Tabletop mount
Wall mount
Telephone outlet
mounting plate
with mounting
studs
Wall mounting
The telephone base comes with the bracket mounted for tabletop use. If wall
mounting is desired, a telephone outlet wall mounting plate with mounting studs is
required. This mounting plate with studs may be available for purchase from many
hardware or consumer electronics retailers and may require professional installation.
1. To remove the bracket, hold the telephone
base in both hands, press the two bracket
tabs and lift the bracket away from slots
and .
2. Connect the telephone line cord and power
adapter to the jacks on the bottom of the
telephone base. Bundle the telephone cord,
and secure it with a twist tie before placing it
inside the bracket.
8
Getting started
Installation options
3. To attach the bracket for wall mounting, insert
the tabs of the bracket into slots
and
on
the telephone base, then press the other bracket
tabs into slots
and
as shown on the right.
4. Plug the power adapter into an electrical outlet
not controlled by a wall switch. Plug the telephone
line cord into a telephone wall jack. To mount the
telephone on the wall, position the mounting holes
and
over the telephone outlet mounting studs.
Press and slide the bracket down firmly so the
telephone is held securely on the telephone outlet
mounting studs.
Telephone outlet mounting studs
Tabletop mounting
To return the bracket from the wall mount to tabletop position, follow the
directions below.
1. Remove the telephone base from the wall. Unplug
the cords from the wall jacks. Remove the bracket
from the telephone base.
3. Route cords through slots. Plug the other end
of the telephone line cord into a telephone
wall jack. Plug the large end of the larger
power adapter into an electrical outlet not
controlled by a wall switch.
9
2. Insert the bracket tabs into slots
on the telephone base, then
and
press the other bracket tabs into
slots
and .
Getting started
Belt clip & optional headset
Install belt clip as shown below if desired.
Snap belt clip
into notches
on both sides
of handset.
To release belt clip
from handset, lift one
side of the belt clip
out of the notch.
For hands-free telephone conversations, use any industry standard 2.5 mm
headset (purchased separately). For best results, use an AT&T 2.5 mm
headset. To order an AT&T 2.5 mm headset, visit our website at
www.telephones.att.com or call 1 (800) 222-3111. In Canada
dial 1 (866) 288-4268.
Plug 2.5 mm headset into
the jack on the side of handset (beneath small rubber
cap).
NOTE: If the sound quality of the
headset is not good, try unplugging it,
and firmly plugging it in again.
10
Telephone operation
Settings
Each cordless handset operates individually from
the other handsets. The ringer sound, ringer volume,
date and time, dial mode and language must be
programmed separately for each cordless handset.
Follow the steps below to program the cordless
handset. To stop at any time, press OFF/CLEAR.
Language
LANGUAGE
The default language for the handset screen
displays is English. To change the language to
Espanol, or Francais:
1. Press MENU/SEL.
2. Press CID or
LANGUAGE.
3. Use
MENU/SEL
DIR
until the screen displays
to change the current setting.
4. Press CID or DIR
to choose among ENGLISH,
FRANCAIS, or ESPANOL.
5. Press
exit.
MENU/SEL
to confirm your selection and
Choose dial mode
DIAL MODE: TONE
The dial mode defaults to tone. If you do not have
touch tone service, you’ll need to change the setting to pulse:
1. Press MENU/SEL.
2. Press CID or DIR
until the screen displays
DIAL MODE: and the current setting.
3. Use MENU/SEL to change the current setting.
4. Press
5. Press
exit.
CID
or DIR
MENU/SEL
11
to display TONE or PULSE.
to confirm your selection and
Telephone operation
Settings
Selectable ringer melodies
RINGER: 1
1. Press MENU/SEL to begin programming.
until the screen displays
2. Press CID or DIR
RINGER: and the current setting.
3. Use MENU/SEL to change the current setting.
4. Press CID or DIR
to display 1, 2, 3, 4 or OFF.
You will hear a sample of each ringer sound.
5. Press MENU/SEL to choose displayed ringer
sound and exit.
DATE/TIME
10:08
02/14
NOTES:
1. You can choose to set the time
manually, or you can allow it
to be set automatically with
incoming caller ID information.
The time will be set automatically only if you subscribe to
caller ID service provided by
your local telephone company
(page 29).
2. Caller ID will not set the year.
NOTE: If you choose OFF, the cordless handset ringer will
be turned off, and the screen will display RINGER OFF and
when the cordless handset is idle (not in use). If there are any
un-reviewed calls, the screen will display XX MISSED CALLS
and
instead of RIGNER OFF and .
Set cordless handset display date and time
1. Press MENU/SEL to begin programming.
2. Press CID or
DATE/TIME.
DIR
until the screen displays
3. Press MENU/SEL to view or set date and time.
4. Press CID or DIR
to change the month in the
date and time line at the bottom of the display,
then press MENU/SEL.
5. Repeat step four to set day, hour, minute, and
AM/PM.
6. Press MENU/SEL to save selection and exit.
12
Telephone operation
Settings
Choose ringer volume setting
RINGER VOL: LOW
NEW VOICE MAIL
10:08AM
02/14
CLR VOICE MAIL
when the cordless
1. Press and hold CID or DIR
handset is idle (not in use). This feature allows you
to choose low, med, high ringer volume or turn
the ringer off.
2. Press CID or DIR to choose the desired option.
You will hear a sample of each ringer volume.
3. Press MENU/SEL to choose blinking ringer volume and exit.
NOTE: If you choose OFF, the handset ringer will be
turned off, and the screen will display RINGER OFF and
when the handset is idle (not in use). If there are any unreviewed calls, the screen will display XX MISSED CALLS and
instead of RIGNER OFF and .
Clear voicemail indication
If you subscribe to voicemail services provided
by your local telephone company, NEW VOICE
MAIL and a
icon will appear on the handset
display when you have a new voicemail message.
The VOICEMAIL light on the telephone base will
flash.
Follow the steps on the left to manually remove
the NEW VOICE MAIL message, the
icon, and
turn off the VOICEMAIL light.
CLEAR? YES
This only turns off the displayed NEW VOICE
MAIL message,
icon and the VOICEMAIL light;
it does not delete your voicemail message(s). Use
this feature when the telephone indicates there
is voicemail when you have none or you have
accessed your voicemail from a remote location
(while away from home). If there is actually a new
voicemail message, your local telephone company
will continue to send a signal which will cause the
NEW VOICE MAIL message, the
icon and the
VOICEMAIL light to turn back on.
NOTE: Telephone company voicemail may alert you to
new messages with a stutter (broken) dial tone. Contact your
telephone company for more details.
13
Telephone operation
Basic operation
Making and answering calls
PHONE ON
00:30
Elapsed
time
NOTE: Only one cordless handset can be on a call
at a time. If another cordless
handset attempts to join a
call, its screen will display
OTHER HANDSET ON and
then OR OUT OF RANGE.
SPEAKER
00:49
To answer an incoming call, press any keys (except
CID, DIR
and OFF/CLEAR). To make a call,
press PHONE/FLASH or
SPEAKER, then dial a
number. Press OFF/CLEAR to hang up.
To predial (preview numbers before dialing),
enter numbers first, then press PHONE/FLASH or
SPEAKER to dial. Press CID then CHAN/DELETE
anytime to make corrections when entering numbers.
The screen displays the elapsed time of the current
call (in hours, minutes and seconds).
NOTES:
1. The elapsed time format is in minutes and seconds
MM:SS until one hour has elapsed, then it will change to
hours, minutes and seconds H:MM:SS.
2. Pressing PHONE/FLASH to access service from your local
telephone service provider will not affect the elapsed time.
The elapsed time will not be carried over to the other cordless handset on a transferred call.
Hands-free speakerphone calls
To answer a call, press
SPEAKER . To make
a call, press
SPEAKER, then dial a number.
During a call press SPEAKER to switch between
hands-free speakerphone and normal handset
use. Press OFF/CLEAR to hang up.
NOTE: If a headset is plugged into the handset, the
handset speakerphone will be disabled.
14
Telephone operation
Basic operation
Last number redial
Ringer
silenced
While the phone is not in use, press REDIAL/PAUSE
on the cordless handset to display the last number
called (up to 32 digits). To dial the number displayed, press PHONE/FLASH or SPEAKER. Or,
after pressing PHONE/FLASH or SPEAKER, press
REDIAL/PAUSE to call the last number dialed.
To delete this number, press REDIAL/PAUSE twice
when the phone is not in use. This will clear the
redial memory and leave it blank.
Press
OFF/CLEAR to exit.
Temporary ring silencing
Press OFF/CLEAR while the telephone is ringing
to silence the ringer temporarily. This will silence
the ringer without disconnecting the call. You can
answer the call. The next incoming call will ring
normally.
15
Telephone operation
Basic operation
Handset locator
HANDSET
If you misplace the handset(s), press
LOCATOR on the telephone base. This starts the
paging tone at the handset(s) for 60 seconds to
help you locate it/them. To stop the paging tone,
press OFF/CLEAR on cordless handset, or place
cordless handset in the telephone base, or press
the HANDSET LOCATOR on the telephone base.
** PAGING **
NOTES:
OFF/CLEAR on any cordless handset will cancel
1. Pressing
the page of that specific handset.
2. If one of the cordless handsets is charging in the base, pressing HANDSET LOCATOR does not generate a paging tone.
16
Telephone operation
Options while on calls
Volume control
Press CID/-VOLUME to decrease the volume.
Press DIR /VOLUME+ to increase the volume.
When changing the volume level, the new setting
is saved.
VOLUME
Call waiting
If you subscribe to call waiting service with your
local telephone company, there will be a beep if
there is an incoming call while you are already on a
call. Press PHONE/FLASH to put your current call
on hold and take the new call. Press PHONE/FLASH
anytime to switch back and forth between calls. For
more information on caller ID, see page 26.
Mute
Press MUTE to silence the microphone. When mute
is on, MICROPHONE MUTED will show on the
handset screen. You will be able to hear the caller,
but the caller will not be able to hear you until you
press MUTE again and resume speaking. When the
mute function is turned off, MICROPHONE ON will
show temporarily on the handset screen.
Temporary tone dialing
If dial pulse (rotary) is selected, you can switch to touch
tone dialing during a call by pressing TONE . This can
be useful if it is necessary to send tone signals for
access to answering systems or long-distance services.
After you hang up or press PHONE/FLASH (to
receive a call waiting call), the telephone automatically returns to dial pulse (rotary) service.
*
Tone
Mute
Channel
Channel selection
During a call, if you hear clicks and pops, or if the
speech sometimes fades, press CHAN/DELETE on
the handset to scan for a clearer radio channel
between cordless handset and base.
17
Telephone operation
Call transfer for E5802B/E1802B
Call transfer
During a conversation, you can transfer the call to
another cordless handset.
• Press MENU/SEL/TRANSFER to transfer the external call to another cordless handset, your cordless handset will display CALL TRANSFERRED
and the other handset will begin ringing.
• To answer the call, press
SPEAKER.
PHONE/FLASH or
NOTES:
1. Before the transferred call is answered, the person at the
originating handset can press PHONE/FLASH or
SPEAKER
to cancel the transfer and resume the external call.
2. If the transferred call is not answered within 30 seconds, the
originating handset will start ringing and show TRANSFERRED
SPEAKER is not pressed within
CALL. If PHONE/FLASH or
another 30 seconds, the external call will end automatically.
3. If the destination cordless handset cannot be found, the
cordless handset that originated the transfer will generate
an error tone and continue the external call automatically.
4. This telephone does not have an intercom function. People
using the cordless handsets cannot talk to each other.
18
Telephone operation
Call transfer for E5833B/E1833B
Call transfer
ENTER 1-3
During a conversation, you can transfer the call to
another cordless handset.
• Press MENU/SEL /TRANSFER to transfer the
external call to another cordless handset. The
handset will display ENTER 1-3. After entering the cordless handset number to which you
want to transfer the call, your cordless handset will display CALL TRANSFERRED and the
selected handset will begin ringing.
• To answer the call, press
SPEAKER.
PHONE/FLASH or
NOTES:
1. Before the transferred call is answered, the person at the
originating handset can press PHONE/FLASH or
SPEAKER
to cancel the transfer and resume the external call.
2. If the transferred call is not answered within 30 seconds, the
originating handset will start ringing and show TRANSFERRED
SPEAKER is not pressed within
CALL. If PHONE/FLASH or
another 30 seconds, the external call will end automatically.
3. If the destination cordless handset cannot be found, the
cordless handset that originated the transfer will generate
an error tone and continue the external call automatically.
4. This telephone does not have an intercom function. People
using the cordless handsets cannot talk to each other.
19
Directory
Memory capacity
PAT WILLIAMS
5551234
Each cordless handset has its own directory. Each
directory can store up to 30 entries (including
nine speed dial locations). Each entry can contain
a number up to 24 digits, and a name up to 15
letters long. A convenient search feature can help
you find and dial numbers quickly (page 24).
NOTE: Each cordless handset has its own directory. Making
changes to the directory of one handset will not affect the directories of the other handsets.
Timeouts and error messages
MEMORY FULL
If you pause for too long while creating an entry,
the procedure will time out and you will have to
begin again.
If all memory locations are in use, the screen
will display MEMORY FULL. You will not be able
to store a new number until an existing one is
deleted.
20
Directory
NOTE: The speed dial feature occupies up to nine of the
thirty memory locations in the
directory. For example, if there
are only five speed dial entries,
then up to 25 entries can be
stored in the directory. If there
are already 30 entries in the
directory, no new directory and
speed dial entries can be stored
in memory until some of the
existing ones are deleted.
1.
MENU/SEL
1. Press MENU/SEL.
or
DIR
CID
SPEED DIAL
3.
You can enter nine speed dial numbers of up to 24
digits. Each number is stored in a one-digit speed
dial location (1-9).
The nine speed dial numbers on handset will be
automatically added to the handset directory.
Press and hold a dial pad key and then press
PHONE/ FLASH or
SPEAKER can easily dial
these telephone numbers. You can also make
existing directory entries into speed dial entries.
To enter a speed dial number
DIRECTORY
2.
Speed dial
MENU/SEL
ENTER 1-9
4.
ENTER NAME
01
(Pages 22-23).
NOTE: You can convert any
directory entry into speed dial
entry (page 25).
or CID until the screen displays
2. Press DIR
SPEED DIAL.
3. Press MENU/SEL.
4. Press dial pad to choose speed dial location (1-9).
5. Enter a name up to 15 characters (page 22),
then press MENU/SEL.
6. Enter a telephone number up to 24 digits (page
21), then press MENU/SEL.
7. Choose distinctive ringing (yes or no) by pressing CID or DIR . If you choose Yes (and if
you have caller ID service), a different ringing
style will alert you when this person calls.
8. Press MENU/SEL to store the number. You will
hear a confirmation tone.
To call a speed dial number
To use speed dialing, press and hold a dial pad
button (1-9) to display the number and name
stored in that speed-dial location, then press
PHONE/FLASH or SPEAKER to dial.
To edit or delete a speed dial number
Press and hold a dial pad button (1-9) to display
the entry you want. Press MENU/SEL, then press
CID or DIR
until the option you want is displayed (page 25).
21
Directory
NOTE: If all memory
locations are in use, an error
tone will sound when you
attempt to enter a number.
This means the memory is full,
and you will not be able to
store a new number until you
delete an existing one.
1.
MENU/SEL
DIRECTORY
New directory entries
To enter a name
• Press MENU/SEL twice.
• The screen will show ENTER NAME.
• Enter the name (up to 15 alphanumeric characters) of the person using the table below.
• Use DIR
to advance to the next space to the
right, or use CID then CHAN/DELETE to delete
a mistake.
• When finished entering the name, press
MENU/SEL.
2.
MENU/SEL
Each press of a particular key causes characters
to be displayed in the following order:
ENTER NAME
3.
PAT JOHNSON_
Options while entering names:
• Press the DIR
the right. Press
button to move the cursor to
twice to enter a space.
DIR
• Press CID then CHAN/DELETE to erase letters if
you make a mistake.
• Press # repeatedly to enter an ampersand (&),
apostrophe ('), comma (,) hyphen (-), period (.),
or pound sign (#).
When finished, press
22
MENU/SEL.
Directory
4.
MENU/SEL
ENTER NUMBER
New directory entries
To enter a number
Use the dial pad to enter up to 24 digits. When
the number is complete, press MENU/SEL.
Options while entering numbers:
• Press CID then CHAN/DELETE to erase digits if
you make a mistake.
5.
PRT JOHNSON
5556789_
6.
MENU/SEL
DISTINCT RING? N
5556789
7.
MENU/SEL
• Press REDIAL/PAUSE to enter a four-second
dialing pause. A P will be inserted.
• When finished entering the telephone number,
press MENU/SEL to confirm.
To assign a distinctive ring
Press CID or DIR
to select Y (yes) or N (no). If
you choose yes (and if you have caller ID service),
a different ringing style will alert you when this
person calls.
Press MENU/SEL to choose the option displayed
and store this entry in the directory.
A D appears in the display of each entry that has
been assigned a distinctive ring.
23
Directory
1.
DIR
DIRECTORY
2.
DIR
ADAM
5551234
To display first entry
DIR
BETH
5554321
To scroll name by
name
-OR-
5
JOHN
5550123
To search alphabetically
Directory search
Follow the steps on the left to browse through the
directory or search to find a specific entry. You can
press OFF/CLEAR anytime to exit the directory.
To browse through the directory
To browse, press DIR then press CID or
to scroll through all entries one by one.
DIR
A D appears in the display of each entry that has
been assigned a distinctive ring (page 23).
NOTE: When reviewing the directory entries, all entries
(including those in the directory and in the speed dial) are displayed in alphabetical order. The entries in the speed dial are
identified by its speed dial number (01-09) in the lower right
corner of the screen.
To search alphabetically
To shorten your search, press DIR then use the
telephone dial pad to enter the first letter of a
name, then press DIR
to scroll forward until you
find the desired name.
If you have more than one name entry that begin
with the same letter, it is necessary to scroll through
all the names beginning with that letter before seeing names that begin with the next letter.
Press dial pad buttons once for the first letter, twice
for the second, three times for the third, as shown
on page 22.
For example, if you have name entries JENNIFER,
KEVIN and LINDA in your directory, pressing the
dial pad key 5 (JKL) once will show JENNIFER,
twice KEVIN, three times LINDA.
NOTE: When searching alphabetically and you press a
dial pad button, if there are no entries beginning with the letters on that button, the handset will show NO DATA.
24
Directory
To change or dial entries
When any entry is displayed, press MENU/SELto see
options. Press CID or DIR
to highlight the option
you want (blinking text), then press MENU/SEL again
to select it.
1.
DIR
DIRECTORY
2.
When EDIT is blinking, press MENU/SEL. You can
change the name and number (or distinctive ring
setting on the cordless handset) by following the
steps described on pages 21-23.
DIR
ADRM
5551234
3.
To edit an entry
MENU/SEL
SPEED EDIT ERASE
5551234
DIR
SPEED EDIT ERASE
5551234
DIR
SPEED EDIT ERASE
5551234
To delete an entry
Press CID or DIR
until ERASE is blinking, then
press MENU/SEL to display a confirmation screen
of ERASE NO YES.
You can press CID or DIR
NO or YES to determine:
to alternate between
• When the YES blinking, press
delete the entry.
• When the NO blinking, press
the procedure.
MENU /SEL
MENU/SEL
to
to cancel
NOTE: Each cordless handset has its own directory.
Making changes to the directory of one handset will not effect
the directories of the other handsets.
To make an entry into a speed dial entry
Press CID or DIR
until SPEED is blinking, press
MENU/SEL, then dial a memory location (1-9) to
transfer this entry to your speed dial directory.
Press MENU/SEL to
choose blinking option.
NOTE: If you use a memory location that is already
assigned to a different entry in the directory, that entry will
remain in the directory, but will no longer be a speed dial
number.
To dial a displayed number
When any directory entry is displayed, press
PHONE/FLASH or
SPEAKER to dial the displayed number.
25
Caller ID summary
Information about caller ID with call waiting
CHRISTINE SMITH
908-555-0100
10:08AM
02/14
This product has a caller ID function with call waiting feature which works with service from your
local telephone company.
Caller ID with call waiting lets you see the name
and telephone number of the caller before answering the telephone, even when on another call.
It may be necessary to change your telephone
service to use this feature. Contact your telephone
company if:
• You have both caller ID and call waiting, but as
separate services (you may need combined service).
• You have only caller ID service, or only call waiting
service.
• You do not have any caller ID or call waiting
services.
This product can be used with regular caller ID
service, or this product’s other features can be
used without subscribing to either caller ID or
combined caller ID with call waiting service. There
are fees for caller ID services, and they may not be
available in all areas.
Depending on your service, you may see the caller’s
number or the caller’s name and number. This product
can provide information only if both you and the
caller are in areas offering caller ID service and if
both telephone companies use compatible equipment.
The time and date are sent by the telephone company
along with the call information.
26
Caller ID operation
Caller ID summary
How caller ID works
CHRISTINE SMITH *
908-555-0100
10:08AM
02/14
If you subscribe to caller ID service provided by
your local telephone company, information about
each caller will be displayed between the first and
second ring.
Appears when a caller
has made two or more
consecutive calls.
Caller’s name
Caller’s phone
number
CHRISTINE SMITH *
908-555-0100
02
10:08AM
02/14
Time of call Date of call
NOTES:
1. Caller ID features will work
only if both you and the
caller are in areas offering
caller ID service, and if both
telephone companies use
compatible equipment.
2. The number shown by your
caller ID will be in the format sent by the telephone
company. The telephone
company usually delivers
10-digit telephone numbers
(area code plus telephone
number). If the telephone
number of the person calling does not exactly match a
number in your directory, the
name will appear as delivered by the telephone company. For example if the telephone company includes the
area code and the directory
number does not, the name
will appear as delivered by
the telephone company.
Call number of
call summary
Appears when
the call is missed
and un-reviewed.
Information about the last 30 incoming calls is
stored in the call summary. You can review the call
summary to find out who has called, return the call,
or copy the caller’s name and number into directory.
If the caller has made two or more consecutive
calls, the repeat tag (*) will be displayed in the top
right corner of the screen.
When the call summary is full, the oldest entry is
deleted to make room for new incoming call information.
If you answer a call before the information appears
on the screen, it will not be saved in the call summary.
About names
Names of callers will be displayed only if the information is provided by your local telephone company.
If the incoming telephone number exactly matches
a telephone number in your directory, the name that
appears on the screen will match the corresponding
name in your directory.
For example: If Christine Smith calls, her name will
appear as CHRIS if this is how you entered it into
your directory.
27
Caller ID operation
Caller ID summary
There are also occasions when other information
or no information is displayed for various reasons:
CHRISTINE SMITH
908-555-0100
10:08AM
Reason
PRIVATE NAME
Caller prefers to remain anonymous.
PRIVATE CALLER
Caller name and telephone
number not revealed at caller's
request.
UNKNOWN NAME
Your local telephone company is
unable to determine the caller's
name.
UNKNOWN CALLER
Your local telephone company
is unable to determine the caller's name and telephone number.
Calls from other countries may
also generate this message.
02/14
02 MISSED CALLS
10:08AM
On-screen message
02/14
Missed calls
When a handset is in idle mode and has calls that
have not been reviewed, its screen will show XX
MISSED CALLS.
Any entries which have not been reviewed will be
counted as MISSED CALLS when the telephone is
idle. Each time a call summary entry marked NEW is
reviewed, the number of missed calls decreases by
one.
If there are too many missed calls and you don’t
want to review them one by one, but still want to
keep them in the call summary, press and hold
OFF/CLEAR for two seconds when the handset is idle.
All the entries in the caller ID summary will be considered old (have been reviewed), and the missed calls
counter is reset to 0.
28
1.
CID
PAT JOHNSON
908-555-0100
03
10:08AM
02/14
2.
CID
CHRIS WILLIAMS
908-555-1234
02
10:08AM
02/14
3.
PHONE/FLASH
PHONE ON 00:10
9085555678
To dial this number
NOTE: Consecutive incoming calls originating from the same
telephone number are identified
by an asterisk at the top right corner of the screen and will be
counted as one call in the caller
ID summary.
CID
PAT JOHNSON
908-555-0100
03
10:08AM
02/14
- OR-
1.
CID
PAT JOHNSON
908-555-0100
03
10:08AM
02/14
2.
#
PAT JOHNSON
1-908-555-0100
03
10:08AM
02/14
3.
Caller ID operation
To review the call summary
The call summary review displays the caller ID in
reverse chronological order, with the latest one (the
one with the highest number) first.
When the phone is not in use, press CID to display
information about the most recent caller.
To review your call summary
Press CID to scroll backward (display older calls)
or DIR
to scroll forward (display newer calls). The
highest call number is the most recent call received.
Each caller ID entry in the call summary will be designated NEW until you have reviewed the call. After
a call has been reviewed, it will disappear.
To return a call
Press PHONE/FLASH or
SPEAKER to call the
number currently displayed.
Dialing options
Caller ID numbers may appear with an area code
that may not be required for local calls.
If the number displayed is not in the correct format,
you can change how it is dialed. Press # repeatedly
to see dialing options. With each button press, a
new option will be displayed. Press PHONE/FLASH
or SPEAKER to dial when the number appears in
the proper format for your area.
The various dialing options are:
908-555-0100
1-908-555-0100
555-0100
1-555-0100
#
PAT JOHNSON
555-0100
03
10:08AM
02/14
4.
#
PAT JOHNSON
1-555-0100
03
10:08AM
02/14
29
Caller ID operation
1.
CID
PAT JOHNSON
908-555-0100
03
10:08AM
02/14
2.
CID
CHRIS WILLIAMS
908-555-1234
02
10:08AM
02/14
3.
CHAN/DELETE
MARK CLAYTON
908-555-5678
01
10:08AM
02/14
- OR27 MISSED CALLS
10:08AM
1.
ERASE ALL NO YES
DIR
ERASE ALL NO YES
3.
To delete a single call summary entry
Press CID to display the first caller ID listing.
Press to find the entry you want to delete, then
press CHAN/DELETE. When the entry is deleted,
the next oldest record is displayed.
To delete all call summary entries
To clear your call summary completely, press and
hold CHAN/DELETE while the phone is idle (not in
use). This will display a confirmation screen asking if you want to erase all entries in the caller ID
summary. If you select yes, the call summary will
be cleared and the screen will return to normal
standby display, and the missed calls counter is
reset to 0.
02/14
CHAN/DELETE
2.
Delete call summary entries
NOTES:
1. Each cordless handset has its own call summary. When you
delete one or all call summary entries from one cordless
handset, the information on all other cordless handsets will
not be affected.
2. When there are already 30 entries in the Caller ID memory,
the next incoming call will automatically cause the oldest
entry to be deleted from the caller ID memory of the handset.
MENU/SEL
10:08AM
02/14
Call summary
cleared
30
Caller ID operation
1.
CID
PAT JOHNSON
908-555-0100
03
10:08AM
02/14
2.
MENU/SEL then
CID
or DIR
DIAL PROGRAM
908-555-0100
03
10:08AM
02/14
3.
MENU/SEL
PAT JOHNSON
9085550100
10:08AM
03
02/14
Add entries to the directory
When any caller ID screen is displayed, follow the
steps at left to enter it into your phone directory.
Both the caller’s name and telephone number will
be entered as they appear in the call summary. At
steps 3-4, you can make any changes to the name
or number by pressing CHAN/DELETE to erase characters, then use the dial pad to enter the correct
information (see pages 22-23 for instructions).
When the number is stored, the screen returns to
the call summary display. The entry copied to your
phone directory remains in the call summary until
deleted.
Edit name as desired
4.
MENU/SEL
PAT JOHNSON
9085550100_
10:08AM
03
02/14
Edit number as desired
5.
MENU/SEL
DISTINCT RING? N
9085550100
03
10:08AM
02/14
6.
MENU/SEL
PAT JOHNSON
908-555-0100
03
10:08AM
02/14
Entry added to
phone directory
31
Appendix
Screen icons, indicator lights & tones
Screen icons & alert tones
Screen icons
The handset speakerphone is in use.
06 MISSED CALLS
-- 1 -02
10:08AM
02/14
Microphone is muted.
Ringer off.
Battery charging (animated display).
Low battery (flashing); place handset in telephone base or
charger to recharge.
Missed and un-reviewed calls.
Handset alert tones
Two short beeps
The volume level is at the maximum or minimum setting.
Double beep every
five seconds
Low battery warning.
Five beeps
Out of range or other handset on when on the line.
Confirmation tone
Command completed successfully.
Indicator lights
CHARGE/IN USE
•
•
•
VOICEMAIL
Flashes when there is new voicemail
(requires voicemail service from your
local telephone company).
On when the cordless
handset is properly
positioned to charge
in the telephone base.
Flashes quickly while
an incoming call is
ringing.
On when one of the
handsets is in use.
CHARGE
On when handset
is in the charger
and charging.
32
SPEAKER
On when the
speakerphone
is in use.
Appendix
Handset display screen messages
Screen display messages
CONNECTING . . .
CONNECTING...
The cordless handset is waiting
for a dial tone.
** RINGING **
There is a call coming in.
** PAGING **
The cordless handset locator
has been activated (all cordless handsets beep to help you
locate them).
NEEDS RECHARGING
Cordless handset battery is
depleted. Place cordless handset
in base or charger to charge the
battery.
BATTERY LOW
Cordless handset battery is low.
Place cordless handset in base
or charger to charge the battery.
PHONE ON
The cordless handset is in use.
SCANNING...
Cordless handset is scanning
for a clear channel to improve
sound quality.
OTHER HANDSET ON
Another cordless handset is on
a call.
Or cordless handset cannot communicate with base. Check base
power, or move closer.
and then
OR OUT OF RANGE
XX MISSED CALLS
33
There are missed and un-reviewed
calls in your call summary.
Appendix
Handset display screen messages
Screen display messages
CONNECTING . . .
CALL TRANSFERRED
You are transferring an external
call on your cordless handset to
another cordless (destination)
handset.
TRANSFERRED CALL
The destination cordless handset
is receiving a transferred call. Or
when the transferred call is not
answered within 30 seconds on
the destination handset, the originating handset displays this message and starts ringing.
ENTER 1-3
(Only for E5833B/E1833B)
Enter the cordless handset
number to which you want to
transfer the call.
RINGER OFF
The cordless handset ringer is
turned off.
MEMORY FULL
You are saving to a full directory.
SPEAKER
The handset speakerphone is in use.
MICROPHONE MUTED
The call switches from normal call
to mute.
MICROPHONE ON
The call switches from mute to
normal call.
34
Appendix
Troubleshooting
If you have difficulty with your telephone, please try the suggestions below. For Customer Service, visit our website at
www.telephones.att.com or call 1 (800) 222-3111. In Canada
dial 1 (866) 288-4268.
My telephone
does not work
at all
• Make sure the battery is installed and charged correctly
(page 7). For optimum daily performance, return the
cordless handset to the telephone base after use.
• Make sure the power adapter is securely plugged into an
outlet not controlled by a wall switch.
• Make sure the telephone line cord is plugged firmly into
the telephone base and the modular wall jack.
• Unplug the telephone’s electrical power. Wait for approximately 15 seconds, then plug it back in. Allow up to one
minute for the cordless handset and base to synchronize.
• Charge the battery in the cordless handset for at least
16 hours.
• Remove and re-insert the battery. If that still does not
work, it may be necessary to purchase a new battery.
• Disconnect the telephone base from the modular jack
and plug in a working telephone. If this telephone does
not work, the problem is probably in the wiring or the
local service. Call the local telephone company.
BATTERY LOW
is displayed on
screen
• Place the handset in the base or charger for recharging.
• Remove and re-install the battery and use it normally
until fully discharged, then recharge the handset on the
telephone base or charger for 16 hours.
• If the above measures do not correct the problem, the
battery may need to be replaced.
The battery does
not charge in
the handset or
the handset battery does not
accept charge
• Make sure the handset is placed in the telephone base
or charger correctly. The CHARGE light on the telephone
base or charger should be on.
• If the cordless handset is in the telephone base but the
CHARGE light is not on, refer to The CHARGE light is
off in this section.
35
Appendix
Troubleshooting
• It may be necessary to purchase a new battery. Please
refer to the Batteries section of this user’s manual.
• The telephone might be malfunctioning. Please refer to
the Limited warranty section of this user’s manual for
further instruction.
The CHARGE
light is off
• Clean the metallic charging contacts on the cordless
handsets and telephone base each month using a pencil
eraser or a dry non-abrasive fabric.
• Make sure the power adapter and telephone line cords
are plugged in correctly and securely.
• Unplug the power adapter. Wait for 15 seconds before
plugging it back in. Allow up to one minute for the cordless handset and telephone base to reset.
• The telephone might be malfunctioning. Please refer to
the Limited warranty section of this user’s manual for
further instruction.
There is no dial
tone
• First, try all the above suggestions.
• Move the cordless handset closer to the telephone base. It
might be out of range.
• The telephone line cord might be malfunctioning. Try installing a new telephone line cord.
• Disconnect the telephone base from the telephone jack and
connect a different telephone. If there is no dial tone on the
telephone either, the problem is in your wiring or local service. Contact your local telephone company.
The telephone
does not ring
when there is an
incoming call
• Make sure the ringer is on (page 12-13).
• Make sure the telephone line cord and power adapter are
plugged in properly (page 6).
• The cordless handset may be too far from the telephone
base. Move it closer to the telephone base.
• There may be too many extension telephones on the telephone
line to allow all of them to ring simultaneously. Try unplugging
some of them.
• If the other telephones in your home are having the same
problem, the problem is in the wiring or local service.
Contact the local telephone company (charges may apply).
36
Appendix
Troubleshooting
• Other electronic products can cause interference to your
cordless telephone. Try installing your telephone as far
away as possible from the following electronic devices:
wireless routers, radios, radio towers, pager towers, cellular telephones, digital telephones, intercoms, room
monitors, televisions, VCRs, personal computers, kitchen
appliances, and other cordless telephones.
• Test a working telephone at the same telephone jack. If
another telephone has the same problem, the problem is
in the telephone jack. Contact your local telephone company (charges may apply).
• The telephone line cord might be malfunctioning. Try
installing a new telephone line cord.
• Re-install the battery and place the cordless handset in
the telephone base.
• Wait for the cordless handset to synchronize with the
telephone base. Allow up to one minute for this to take
place.
My phone rings but • The cordless handset may be too far from the telephone
base. Move closer to the telephone base and try to
when I try to answer
answer the call.
the call the handset screen shows
CONNECTING…
I cannot dial out • First, try all the above suggestions.
• Make sure there is a dial tone before dialing. It is normal if the cordless handset takes a second or two to
synchronize with the telephone before producing a dial
tone. Wait an extra second before dialing.
• Make sure the telephone is set to the correct dial mode
(pulse dial or tone dial) for the service in your area. Refer
to the Handset settings section of this user’s manual
(page 11) to set the dial mode.
• If the other telephones in your home are having the
same problem, the problem is in the wiring or local service. Contact your local telephone company (charges may
apply).
37
Appendix
Troubleshooting
• Eliminate any background noise. Noise from a television, radio, or other appliances may cause the telephone
to not dial out properly. If you cannot eliminate the
background noise, first try muting the cordless handset before dialing, or dialing from another room in your
home with less background noise.
There is noise or
interference during a telephone
conversation
• The handset may be out of range. Move it closer to the
telephone base.
My calls fade out
or cut in and out
when I am using
t h e c o rd l e s s
handset
• Appliances or other cordless telephones plugged into
the same circuit as the telephone base can cause interference. Try moving the appliance or telephone base to
another outlet.
• Other electronic products can cause interference to your
cordless telephone. Try installing your telephone as far
away as possible from the following electronic devices:
wireless routers, radios, radio towers, pager towers, cellular telephones, digital telephones, intercoms, room
monitors, televisions, VCRs, personal computers, kitchen
appliances, and other cordless telephones.
• Microwave ovens operate on the same frequency as your
telephone. It is normal to experience static on your telephone
while the microwave oven is operating. Do not install
this telephone in the same outlet or near a microwave oven.
• If your telephone is plugged in with a modem or a surge
protector, plug the telephone (or modem/surge protector) into a different location. If this solves the problem,
re-locate your telephone or modem farther apart from
each other, or use a different surge protector.
• The layout of your home or office might be limiting the
operating range. Try moving the base to another location, preferably a higher location for better reception.
• Disconnect the telephone base from the modular jack
and plug in a corded telephone. If calls are still not clear,
the problem is probably in the wiring or local service.
Contact your local service company (charges may apply).
38
Appendix
Troubleshooting
• Select channels four through 10 for your router (refer to
the user’s manual of your router for more information).
• If the other telephones in your home are having the
same problem, the problem is in the wiring or local service. Contact the local telephone company (charges may
apply).
• Do you have DSL service? If yes, you need to have a DSL
filter installed at every telephone jack that has a telephone
connected to it. Contact your DSL service provider for filter
information.
I hear other
• Disconnect the telephone base from the telephone jack.
calls when using
Plug in a different telephone. If you still hear other calls,
the telephone
the problem is probably in the wiring or local service.
Call your local telephone company.
My caller ID fea- • Caller ID is a subscription service. You must subscribe to
tures are not workthis service from your local telephone company for this
ing properly
feature to work on your telephone.
• The caller may not be calling from an area which supports caller ID.
• Both you and the caller’s telephone companies must use
equipment which are compatible with caller ID service.
• If you subscribe to DSL service, install a DSL filter to the
telephone line between the telephone base and the telephone
line jack. Contact your DSL service provider for filter information.
The system does • Make sure you subscribe to caller ID with call waiting
features services provided by the local telephone company.
not receive caller
ID or the system • The caller may not be calling from an area which supports
does not display
caller ID.
caller ID during
• Both you and the caller’s telephone companies must use
call waiting
equipment which are compatible with caller ID service.
• If you subscribe to DSL service, install a DSL filter to the
telephone line between the telephone base and the telephone
line jack. Contact your DSL service provider for filter information.
39
Appendix
Troubleshooting
Common cure
for electronic
equipment
• If the telephone is not responding normally, try putting
the cordless handset in the telephone base or the
charger. If it does not seem to respond, try the following
(in the order listed):
1. Disconnect the power to the telephone base.
2. Disconnect the battery on the cordless handset.
3. Wait a few minutes before connecting power to the
telephone base.
4. Re-install the battery and place the cordless handset
into the telephone base or charger.
5. Wait for the cordless handset to synchronize its connection with the telephone base. Allow up to one
minute for this to take place.
40
Appendix
Important safety instructions
This symbol is to alert you to important operating or servicing instructions that may
appear in this user’s manual. Always follow basic safety precautions when using this product to
reduce the risk of injury, fire, or electric shock.
Safety information
• Read and understand all instructions in the user’s manual. Observe all
markings on the product.
• Avoid using a telephone during a thunderstorm. There may be a slight
chance of electric shock from lightning.
• Do not use a telephone in the vicinity of a gas leak. If you suspect a gas
leak, report it immediately, but use a telephone away from the area where
gas is leaking. If this product is a cordless model, make sure the base is
also away from the area.
• Do not use this product near water, or when you are wet. For example,
do not use it in a wet basement or shower, or next to a swimming pool,
bathtub, kitchen sink, or laundry tub. Do not use liquids or aerosol sprays
for cleaning. If the product comes in contact with any liquids, unplug any
line or power cord immediately. Do not plug the product back in until it has
dried thoroughly.
• Install this product in a protected location where no one can trip over
any line or power cords. Protect cords from damage or abrasion.
• If this product does not operate normally, read Troubleshooting in this
user’s manual. If you cannot solve the problem, or if the product is damaged, refer to the limited warranty. Do not open this product except as may
be directed in your user’s manual. Opening the product or reassembling it
incorrectly may expose you to hazardous voltages or other risks.
• If this product has user-replaceable batteries, replace batteries only
as described in your user’s manual. Do not burn or puncture batteries
— they contain caustic chemicals.
• If this product has a three-prong (grounding) plug or a polarized plug
with one wide prong, it may not fit in non-polarized outlets. Do not defeat
the purpose of these plugs. If they do not fit in your outlet, the outlet
should be replaced by an electrician.
CAUTION: Use only the power adapter provided with this
product. To obtain a replacement, visit our website at www.
telephones.att.com or call 1 (800) 222-3111. In Canada dial
1 (866) 288-4268.
41
Appendix
Important safety instructions
Especially About Cordless Telephones
• Privacy: The same features that make a cordless phone convenient create
some limitations. Telephone calls are transmitted between the telephone
base and handset by radio waves, so there is a possibility that your cordless phone conversations could be intercepted by radio receiving equipment within range of the cordless handset. For this reason, you should
not think of cordless phone conversations as being as private as those
on corded phones.
• Electrical power: The telephone base of this cordless telephone must be
connected to a working electrical outlet. The electrical outlet should not be
controlled by a wall switch. Calls cannot be made from the handset if the
telephone base is unplugged or switched off, or if the electrical power
is interrupted.
• Power adapter: This power adapter is intended to be plugged into a vertical
wall outlet or a floor outlet.
• Potential TV interference: Some cordless telephones operate at frequencies
that may cause interference to TVs and VCRs. To minimize or prevent such interference, do not place the telephone base of the cordless telephone near or on
top of a TV or VCR. If interference is experienced, moving the cordless telephone
farther away from the TV or VCR will often reduce or eliminate the interference.
• Rechargeable batteries: This product contains either Nickel-Cadmium or
Nickel-Metal Hydride rechargeable batteries. Exercise care in handling batteries in order not to short the battery with conducting material such as rings,
bracelets, and keys. The battery or conductor may overheat and cause harm.
Observe proper polarity between the battery and the battery charger.
• Nickel-cadmium rechargeable batteries: Must be recycled or disposed of
properly. Do not dispose of in household garbage. Do not burn or puncture.
Like other batteries of this type, if burned or punctured, they could release
caustic material which could cause injury.
The RBRC™ Seal means that the manufacturer is voluntarily participating in an
industry program to collect and recycle nickel-cadmium rechargeable batteries
when taken out of service within the United States. These batteries may be taken
to a participating local retailer of replacement batteries or recycling center. Or you may call 1
(800) 8 BATTERY for locations accepting spent nickel-cadmium Batteries.
42
Appendix
Important safety instructions
• Nickel-metal hydride rechargeable batteries: Dispose of these batteries
in a safe manner. Do not burn or puncture. Like other batteries of this type,
if burned or punctured, they could release caustic material which could
cause injury.
The RBRC™ Seal means that the manufacturer is voluntarily participating in an industry
program to collect and recycle nickel-metal rechargeable batteries when taken out of
service within the United States. These batteries may be taken to a participating local
retailer of replacement batteries or recycling center. Or you may call 1 (800) 8 BATTERY for locations
accepting spent nickel-metal Batteries.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless telephones):
Wireless Technology Research, LLC (WTR), an independent research entity, led
a multidisciplinary evaluation of the interference between portable wireless
telephones and implanted cardiac pacemakers. Supported by the U.S. Food
and Drug Administration, WTR had recommended to physicians that:
Pacemaker patients
• Should keep wireless phones at least six inches from the pacemaker.
• Should NOT place wireless phones directly over the pacemaker, such as in a
breast pocket, when it is turned ON.
• Should use the wireless phone at the ear opposite the pacemaker.
WTR’s evaluation did not identify any risk to bystanders with pacemakers from
other persons using wireless phones.
Especially about telephones answering systems
Two-way recording: This telephone does not sound warning beeps to let the other
party know that the call is being recorded. To ensure that you are in compliance
with any federal or state regulations regarding recording a telephone call, you
should start the recording process and then inform the other party that you are
recording the call.
SAVE THESE INSTRUCTIONS
43
Appendix
FCC Part 68 & ACTA
This equipment complies with Part 68 of the FCC rules and with technical
requirements adopted by the Administrative Council for Terminal Attachments
(ACTA). The label on the back or bottom of this equipment contains, among
other things, a product identifier in the format US: AAAEQ##TXXXX. This identifier must be provided to your local telephone company upon request.
The plug and jack used to connect this equipment to premises wiring and the
telephone network must comply with applicable Part 68 rules and technical
requirements adopted by ACTA. A compliant telephone cord and modular plug
is provided with this product. It is designed to be connected to a compatible
modular jack that is also compliant. An RJ11 jack should normally be used
for connecting to a single line and an RJ14 jack for two lines. See Installation
Instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices
you may connect to your telephone line and still have them ring when you
are called. The REN for this product is encoded as the 6th and 7th characters
following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In
most, but not all areas, the sum of all RENs should be five (5.0) or less. For
more information, please contact your local telephone company.
This equipment may not be used with Party Lines. If you have specially wired
alarm dialing equipment connected to your telephone line, ensure the connection of this equipment does not disable your alarm equipment. If you have
questions about what will disable alarm equipment, consult your telephone
company or a qualified installer.
If this equipment is malfunctioning, it must be unplugged from the modular
jack until the problem has been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents. For
repair procedures, follow the instructions outlined under the Limited Warranty.
If this equipment is causing harm to the telephone network, the telephone
company may temporarily discontinue your telephone service. The telephone
company is required to notify you before interrupting service. If advance
notice is not practical, you will be notified as soon as possible. You will be
given the opportunity to correct the problem and the telephone company is
required to inform you of your right to file a complaint with the FCC. Your telephone
company may make changes in its facilities, equipment, operation, or procedures
that could affect the proper functioning of this product. The telephone company is
required to notify you if such changes are planned.
44
Appendix
FCC Part 68 & ACTA
If this product is equipped with a corded or cordless handset, it is hearing aid
compatible.
If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g., police, fire, medical) in these locations. If you
do store or test emergency numbers, please:
• Remain on the line and briefly explain the reason for the call before hanging up.
• Perform such activities in off-peak hours, such as early morning or late
evening.
45
Appendix
FCC Part 15
This equipment has been tested and found to comply with the requirements
for a Class B digital device under Part 15 of the Federal Communications
Commission (FCC) rules.
These requirements are intended to provide reasonable protection against
harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the
party responsible for compliance could void the user’s authority to operate
the equipment.
To ensure safety of users, the FCC has established criteria for the amount of
radio frequency energy that can be safely absorbed by a user or bystander
according to the intended usage of the product. This product has been tested
and found to comply with the FCC criteria. The handset may be safely held
against the ear of the user. The telephone base shall be installed and used
such that parts of the user’s body other than the hands are maintained at a
distance of approximately 20 cm (8 inches) or more. If you choose to use a
clipping device, please make sure to only use the supplied AT&T belt clip.
46
Appendix
Limited warranty
The AT&T brand is used under license - any repair, replacement
or warranty service, and all questions about this product should
be directed to: In the United States of America visit our website
at www.telephones.att.com or call 1 (800) 222-3111. In Canada
dial 1 (866) 288-4268.
1. What does this limited warranty cover?
The manufacturer of this AT&T-branded product warrants to the holder of
a valid proof of purchase (“CONSUMER” or “you”) that the product and all
accessories provided in the sales package (“PRODUCT”) are free from defects
in material and workmanship, pursuant to the following terms and conditions,
when installed and used normally and in accordance with the PRODUCT operating instructions. This limited warranty extends only to the CONSUMER for
products purchased and used in the United States of America and Canada.
2. What will be done if the PRODUCT is not free from defects in materials
and workmanship during the limited warranty period (“materially defective
PRODUCT”)?
During the limited warranty period, the manufacturer’s authorized service
representative will repair or replace at the manufacturer’s option, without
charge, a materially defective PRODUCT. If the manufacturer repairs the
PRODUCT, they may use new or refurbished replacement parts. If the manufacturer chooses to replace the PRODUCT, they may replace it with a new
or refurbished PRODUCT of the same or similar design. The manufacturer
will retain defective parts, modules, or equipment. Repair or replacement of
the PRODUCT, at the manufacturer’s option, is your exclusive remedy. The
manufacturer will return repaired or replacement products to you in working condition. You should expect the repair or replacement to take approximately 30 days.
3. How long is the limited warranty period?
The limited warranty period for the PRODUCT extends for ONE (1) YEAR
from the date of purchase. If the manufacturer repairs or replaces a materially defective PRODUCT under the terms of this limited warranty, this limited warranty also applies to repaired or replacement PRODUCT for a period
of either (a) 90 days from the date the repaired or replacement PRODUCT
is shipped to you or (b) the time remaining on the original one-year limited
warranty; whichever is longer.
47
Appendix
Limited warranty
4. What is not covered by this limited warranty?
This limited warranty does not cover:
• PRODUCT that has been subjected to misuse, accident, shipping or other
physical damage, improper installation, abnormal operation or handling,
neglect, inundation, fire, water, or other liquid intrusion; or
• PRODUCT that has been damaged due to repair, alteration, or modification by anyone other than an authorized service representative of the
manufacturer; or
• PRODUCT to the extent that the problem experienced is caused by signal
conditions, network reliability or cable or antenna systems; or
• PRODUCT to the extent that the problem is caused by use with non-AT&T
accessories; or
• PRODUCT whose warranty/quality stickers, PRODUCT serial number
plates or electronic serial numbers have been removed, altered or rendered illegible; or
• PRODUCT purchased, used, serviced, or shipped for repair from outside the
United States of America or Canada, or used for commercial or institutional
purposes (including but not limited to products used for rental purposes); or
• PRODUCT returned without valid proof of purchase (see item 6 below); or
• Charges for installation or setup, adjustment of customer controls, and
installation or repair of systems outside the telephone.
5. How do you get warranty service?
To obtain warranty service in the United States of America, call
1 (800) 222-3111; In Canada, please dial 1 (866) 288-4268.
NOTE: Before calling for service, please review the user’s manual - a check of
the PRODUCT controls and features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage
during transit and transportation and are responsible for delivery or handling
charges incurred in the transport of the PRODUCT(s) to the service location.
The manufacturer will return repaired or replaced PRODUCT under this limited
warranty to you, transportation, delivery or handling charges prepaid. The
manufacturer assumes no risk for damage or loss of the PRODUCT in transit.
If the PRODUCT failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, the manufacturer will
notify you and will request that you authorize the cost of repair prior to any
further repair activity. You must pay for the cost of repair and return shipping
costs for the repair of products that are not covered by this limited warranty.
48
Appendix
Limited warranty
6. What must you return with the PRODUCT to get warranty service?
You must:
a. Return the entire original package and contents including the PRODUCT
to the service location along with a description of the malfunction or difficulty; and
b. Include “valid proof of purchase” (sales receipt) identifying the PRODUCT
purchased (PRODUCT model) and the date of purchase or receipt; and
c. Provide your name, complete and correct mailing address, and telephone
number.
7. Other limitations
This warranty is the complete and exclusive agreement between you and the
manufacturer of this AT&T branded PRODUCT. It supersedes all other written
or oral communications related to this PRODUCT. The manufacturer provides
no other warranties for this PRODUCT. The warranty exclusively describes all
of the manufacturer’s responsibilities regarding the PRODUCT. There are no
other express warranties. No one is authorized to make modifications to this
limited warranty and you should not rely on any such modification.
State/Provincial Law Rights: This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular
purpose and merchantability (an unwritten warranty that the PRODUCT is
fit for ordinary use) are limited to one year from date of purchase. Some
states/provinces do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you. In no event shall the
manufacturer be liable for any indirect, special, incidental, consequential, or
similar damages (including, but not limited to lost profits or revenue, inability to use the PRODUCT or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this
PRODUCT. Some states/provinces do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Please retain your original sales receipt as
proof of purchase.
49
Appendix
Technical specifications
RF frequency band
(handset to telephone base)
5863.8 MHz — 5872.5 MHz
RF frequency band
(telephone base to handset)
912.75 MHZ — 917.10 MHz
Channels
30
Modulation
FM
Operating temperature
32°F — 122°F
0°C — 50°C
Telephone base voltage
(AC voltage, 60Hz)
104 — 129Vrms
Telephone base voltage
(AC adapter output)
AC9V @250mA
Handset voltage
DC3.1 — 4.3V 400mAh
Charger voltage
(AC adapter output)
DC9V @150mA
Rechargeable battery
3.6V 400mAh
Telephone operating range
This cordless telephone operates with the maximum power allowed by the Federal
Communications Commission (FCC). Even so, the handset(s) and telephone base
can communicate over only a certain distance - which can vary with the locations
of the telephone base and handset(s), the weather, the layout, and the construction of your home or office.
50
Appendix
Index
A
Alert tones, 32
Answering calls, 14
I
Incoming call summary, 27
Incoming calls, answering, 14
Indicator lights, 32
B
Battery charging, 7
Battery installation, 7
Battery low, 7
Belt clip, 10
L
Last number redial, 15
M
Making calls, 14
Menus, 2
Missed calls, 28
Mute, 17
C
Call waiting, 17
Caller ID, 26
add entries to phone directory, 31
delete entries, 30
dial entries, 29
Channel, 17
N
Names,
enter into directory, 22
search for, 24
D
Delete call summary entries, 30
Delete redial entries, 15
Dialing,
directory dialing, 25
from a CID record, 29
mode, 11
Directory, 20
dial number, 25
edit entries, 25
make an entry, 25
search, 24
DSL filter, 6
P
Power adapter, 6
E
Elapsed time, 14
S
Screen display messages, 33
Search for names, 24
Speakerphone, 14
Q
Quick reference guide, 2-3
R
Receiving calls, 14
Recharging, 7
Redial, 15
Ring silencing, 15
Ringer sound, 12
Ringer volume, 13
F
Flash (switchhook flash), 17
T
Technical specifications, 50
Temporary tone dialing, 17
Troubleshooting, 35
H
Hands-free use, 14
Handset locator, 16
Headset, 10
V
Volume control, 17
51
www.telephones.att.com
© 2007 Advanced American Telephones. All rights reserved.
AT&T and the AT&T logo are trademarks of AT&T Knowledge Ventures,
licensed to Advanced American Telephones. Printed in China. Issue 5 AT&T 06/07.
91-001105-040-100
Download PDF

advertising