Specifications | Aube Technologies CT230-120GA Thermostat User Manual

400-230-000-D (PB112-12VDC) ENG.fm Page 1 Wednesday, February 7, 2007 9:11 AM
Installation Instructions
MASTER THERMOSTATS
TH113-A/F/AF (12VDC)
TH114-A/F/AF (12VDC)
TH115-A/F/AF (12VDC)
TH116-A/F/AF (12VDC)
1. Introduction
This master and slave unit system is specially
designed for large floor heating applications
exceeding 15 A.
The master thermostat controls a single or
multiple floor heating zones driven by slave units.
The master thermostat can control up to 10 slave
units.
Each slave unit drives its own zone and is
equipped with a GFCI test button and warning
light as well as an On/Standby switch to facilitate
maintenance on specific zones of the floor
installation.
2. Operation
Master Thermostat
The master unit controls the temperature and
sends a signal to slave units when heating is
required. The floor sensor is connected to the
master unit. The master unit is powered by the
slave units.
SLAVE UNITS
CT230-120GA
CT230-120GB
CT230-240GA
CT230-240GB
3.2 Slave Units - Installation and Wiring
The slave units can operate on different voltages (e.g. 5 units @ 120 V and 5 @ 240 V).
• Required parts: CT230-120GA, -120GB, -240GA or -240GB
• Installation: On an electrical box
• Location: Installation near the master
thermostat is not required (i.e. can be
installed in a utility room).
• Wiring: The power bases are joined
through a daisy chain connection.
n
Connect the 120 V or 240 V power
base wires to the power (line) and to
the load (floor) using solderless connectors for copper wires, and secure
the base to the electrical box.
o
Affix the wiring sticker (in the CT230
box) to the base.
p
Connect the slave power bases
together as per FIGURE 1.
q
Once installation and wiring is complete, mount the CT230 interface:
a) Align the bracket tabs of the
CT230 with the holes located on
top of the power base.
b) Secure the CT230 interface using the screw (captive).
r
Switch all slave power bases to STANDBY by sliding the protective door upwards
and positioning the switch to STANDBY.
Install and connect the master unit (see 3.3).
Slave Unit
The slave unit receives the signal sent by the
master unit and activates its load.
NOTE: There must be a minimum of one slave
unit ON to power the master unit.
3. Installation
Turn off power to the heating system at the
main power panel to avoid electrical shock.
Installation should be carried out by an
electrician.
3.1 Wiring Guidelines
• The wire distance between the master thermostat and slave unit should not exceed 500 ft.
(150 m).
• The floor sensor cable should not exceed
200 ft. (60 m).
• A 3-wire 20 AWG cable is recommended.
FIGURE 1
Connections
400-230-000-D
2/7/07
1/2
400-230-000-D (PB112-12VDC) ENG.fm Page 2 Wednesday, February 7, 2007 9:11 AM
3.3 Master Thermostat - Installation and Wiring
Technical Specifications
WARNING: Make sure all slave units are in STANDBY mode.
Temperature:
- Operation: 32°F to 122°F (0°C to 50°C)
- Storage: -4°F to 122°F (-20°C to 50°C)
•Required parts:
TH113-A/F/AF (12VDC),
TH114-A/F/AF (12VDC),
TH115-A/F/AF (12VDC) or
TH116-A/F/AF (12VDC)
Power supply
12 V from remote unit
Temperature control: AF (ambient with floor limit) / A (ambient)
Maximum
slave units
up to 10 slave units per
master thermostat
•
Install the master thermostat in the controlled area.
Wire gauge
20 AWG
•
Choose a location about 5 ft. above the floor in an area where the temperature is stable.
Size (H • W • D)
BASE
4.63 x 2.7 x 0.61 in.
(117.5 x 68.3 x 15 mm)
•
Avoid locations where there are air drafts (top of staircase, air outlet), dead air
spots (behind a door), direct sunlight or concealed chimneys or stove pipes.
• Location: anywhere easily accessible to users.
Temperature control: F (floor)
•
s
TH113/TH114/TH115/TH116 (A/F/AF-12VDC)
Can be installed anywhere.
Wire the 12 VDC base to the nearest slave unit.
The floor sensor must be installed in an area where average temperature can be
read. The cable must follow the wall down to the floor and must not cross any
heater wires or be directly on or adjacent to a heating wire.
For maximum performance, the sensor probe should be centered between the
wires in the mat (max. 80°C).
t
Push the excess wire into the wall, secure the base using the provided screws
and wall anchors, and install the TH11x thermostat onto the base.
u
Once the thermostat is installed, return power to heating system and switch all
slave units and the master thermostat to ON.
NOTE: Refer to the TH11x user guide for technical
specifications.
CT230-120GA/120GB/240GA/240GB
Supply
- PB112-120
- PB112-240
1800 W @ 120 VAC
60 Hz, 15 A resistive
3600 W @ 240 VAC
60 Hz, 15 A resistive
GFCI
GA=5 mA / GB=30 mA
Certification
c CSA us
Size (H • W • D)
BASE
4.63 x 2.7 x 1.45 in.
(117.5 x 68.3 x 37 mm)
Size (H • W • D)
INTERFACE
4.67 x 2.74 x 0.67 in.
(118.6 x 69.6 x 17 mm)
Warranty
3.4 Slave Units - GFCI Test
We recommend you test the GFCI immediately after installing the thermostat, and
once a month thereafter to ensure it is operating properly.
If the test warning light comes ON during normal operation, cut power to heating
system from the main power panel and verify the installation.
n
o
Slide the protective door upwards and make sure the switch is ON.
Press TEST.
•
The test is successful if the TEST warning light is ON and power is cut off.
•
If the test fails (first installation test):
a. Verify installation
b. Check the load wires
c. Once you've identified the problem, run the GFCI test again
•
Aube warrants this product, excluding battery, to be free
from defects in the workmanship or materials, under normal use and service, for a period of three (3) years from the
date of purchase by the consumer. If at any time during the
warranty period the product is determined to be defective
or malfunctions, Aube shall repair or replace it (at Aube's
option).
If the product is defective,
(i)
return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it, or
(ii)
contact Aube. Aube will make the determination
whether the product should be returned, or whether
a replacement product can be sent to you.
This warranty does not cover removal or reinstallation
costs. This warranty shall not apply if it is shown by Aube
that the defect or malfunction was caused by damage
which occurred while the product was in the possession of
a consumer.
Aube's sole responsibility shall be to repair or replace the
product within the terms stated above. AUBE SHALL NOT
BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND,
INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING, DIRECTLY OR INDIRECTLY,
FROM ANY BREACH OF ANY WARRANTY, EXPRESS
OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some provinces, states or regions do not allow the
exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY
AUBE MAKES ON THIS PRODUCT. THE DURATION OF
ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE
THREE-YEAR DURATION OF THIS WARRANTY. Some
provinces, states or regions do not allow limitations on how
long an implied warranty lasts, so the above limitation may
not apply to you.
This warranty gives you specific legal rights, and you may
have other rights which vary from province, state or region
to another.
If the test fails (monthly maintenance):
Service
a. Cut power to heating system from the main power panel and call customer
service
For any questions regarding the product installation or
operation, contact us at:
p
When the test is successful, reset the slave unit by switching from ON to
STANDBY then back to ON.
q
Repeat steps 1 to 3 for all slave units.
705 Montrichard
Saint-Jean-sur-Richelieu, Quebec
J2X 5K8
Canada
Tel.: (450) 358-4600
Toll-free: 1-800-831-AUBE
Fax: (450) 358-4650
E-mail: aube.service@honeywell.com
For more information on our products, visit us at:
www.aubetech.com
400-230-000-D
2/7/07
2/2
Download PDF

advertising