Owner`s manual | Audiovox AAAAAV-427V-427V-427V-427V

OWNER'S MANUAL
AND INSTALLATION GUIDE
AV-427
DETACHABLE FRONT PANEL AM/FM/MPX RADIO
WITH AUTO-REVERSE CASSETTE PLAYER,
CD CHANGER CONTROLS AND QUARTZ CLOCK
INST
ALL
AT ION INSTRUC
INSTALL
ALLA
INSTRUCTT IONS
INSTALLATION INSTRUCTIONS
This unit is designed for installation in cars, trucks, and vans with an existing radio opening. In many cases, a special
installation kit will be required to mount the radio to the dashboard. These kits are available at electronics supply stores
and car stereo specialist shops. Always check the kit application before purchasing to make sure the kit works with
your vehicle.
If you need a kit but cannot find it available, call our toll-free “HELP” line at
1-800-645-4994.
UNIVERSAL INSTALLATION PROCEDURE USING MOUNTING SLEEVE
1. Remove the detachable front panel if it is attached to the chassis by pushing the “Release” button. Slide the mounting
sleeve off of the chassis. If it is locked into position, use the removal tools (supplied) to disengage it.
2. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully
cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening or
cause it to bend or bow. Check that there will be sufficient space behind the dashboard for the radio chassis.
3. Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve. With the sleeve fully inserted
into the dashboard opening, bend as many of the tabs outward as necessary so that the sleeve is firmly secured to
the dashboard.
4. Place the radio in front of the dashboard opening so that the wiring can be brought through the mounting sleeve.
Follow the wiring diagram carefully and make certain all connections of the wiring harness are secure and insulated
with wire nuts or electrical tape to insure proper operation of the unit. After completing the wiring connections, attach
the front panel and turn the unit on to confirm operation (ignition switch must be “on”). If unit does not operate, recheck all wiring until problem is corrected. Once proper operation is achieved, turn off the ignition switch and proceed
with final mounting of the chassis.
5. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated and the spring
clips lock it into place.
6. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex
nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below
the radio using the screw and hex nut provided. Bend the strap to position it as necessary.
CAUTION: The rear of the radio must be supported with the strap to prevent damage to the dashboard from the
weight of the radio or improper operation due to vibration.
7. Re-attach the front panel to the chassis and test radio operation by referring to the Operating Instructions for the unit.
INSTALLATION USING KITS
1. If your vehicle requires the use of an installation kit to mount this radio, follow the instructions included with the
installation kit to attach the radio to the mounting plate supplied with the kit.
2. Wire and test the radio as described in Step 4 above.
3. Install the radio/mounting plate assembly to the sub-dashboard according to the instructions of the installation kit.
4. Attach the support strap to the radio and dashboard as described in Step 6 above.
5. Replace the dashboard trimpanel.
ISO INSTALLATION PROCEDURE
1
This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets
of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the dashboard. Please
consult with your local car stereo specialist shop for assistance on this type of installation.
1. Remove the existing factory radio from its dashboard or center console mounting. Save all hardware and brackets
as they will be used to mount the new radio.
2. Carefully un-snap the plastic frame from the front of the new radio chassis. Remove and discard the frame.
3. Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio.
CAUTION : DO NOT EXCEED M5 X 8 MM MAXIMUM SCREW SIZE.
LONGER SCREWS MAY TOUCH AND DAMAGE COMPONENTS INSIDE THE CHASSIS.
4. Wire the new radio to the vehicle as per step 4 above.
5. Mount the new radio assembly to the dashboard or center console using the reverse procedure of step 1.
UNIVERSAL INSTALLATION USING MOUNTING SLEEVE
EXISTING DASH OPENING (FILE EDGES TO FIT IF NECESSARY-DO NOT OVERFILE)
NOTE
NOTE:: IF DASH IS SOLID, USE MOUNTING SLEEVE AS A TEMPLATE & CUT OPENING
NUT
PERFORATED STRAP
FASTEN THIS END TO
SCREW STUD ON
REAR OF CHASSIS
BEND TOP TABS
UPWARD
BEND BOTTOM TABS
DOWNWARD
SCREW
INST
ALL
AT ION INSTRUC
INSTALL
ALLA
INSTRUCTT IONS
Toll-Fr
ion As
sis
oll-Free e Ins
Instt allat
allation
Assis
sistt anc
ancee
The installation and wiring connections for this unit are so simple, we doubt you'll need our help, but, if you do, we're
here to help you. Just call our toll-free telephone assistance line at 1-800-645-4994 during the days and hours shown
(U.S.A. and Canada only).
TIME ZONE
EASTERN
PACIFIC
MOUNTAIN
CENTRAL
DAY
8:30AM - 7PM
MON.-FRI.
5:30AM - 4PM
6:30AM - 5PM
7:30AM - 6PM
9AM - 5PM
SATURDAY
6AM - 2PM
7AM - 3PM
8AM - 4PM
RADIO
SCREW STUD
REMOVAL
TOOLS
MOUNTING SLEEVE
FASTEN THIS END TO SECURE PART
OF DASHBOARD.
DRILL HOLE IF NECESSARY.
DETACHABLE
FRONT PANEL
ISO INSTALLATION
REMOVE THE PLASTIC FRAME FROM THE
FRONT OF THE CHASSIS BY CAREFULLY
UN-SNAPPING IT.
TYPICAL INSTALLATION
MAX. SIZE
M5 x 8
UN-SNAP AT 2 PLACES
EACH ON TOP AND
BOTTOM
PLASTIC FRAME
MAX. SIZE
M5 x 8
FACTORY MOUNTING BRACKETS
2
R A DIO WIRING
R A DIO WIRING
REFER TO PAGE 4 FOR SPEAKER WIRING
ANTENNA
AUTOMATIC
ANTENNA
BLUE
IMPORTANT
THE BLUE WIRE CAN BE USED TO
REMOTELY ACTIVATE AN AUTOMATIC ANTENNA OR AN EXTERNAL
AMPLIFIER (SEE ANTENNA OR AMPLIFIER MANUAL)
EXISTING
ANTENNA
CABLE
FUSEBLOCK
“RADIO” FUSE
+ 12V ACCESSORY
RED
SCREW
BLACK
CAR BATTERY
METAL PART OF DASH
(DRILL HOLE IF NECESSARY)
YELLOW
IMPORTANT
YELLOW WIRE MUST BE CONNECTED AS SHOWN
OR RADIO WILL NOT OPERATE PROPERLY
4 PIN PLUGS
9 PIN PLUG
(SEE PAGE 4 FOR SPEAKER WIRING)
ANTENNA LEAD ON
REAR OF RADIO
RADIO
3
POSITIVE (+) TERMINAL
12V BATTERY
REFER TO PAGE 3
FOR RADIO WIRING
WARNING!
l
l
l
l
THE AMPLIFIERS IN THIS RADIO ARE ONLY DESIGNED FOR USE WITH 4 SPEAKERS.
NEVER COMBINE (BRIDGE) OUTPUTS FOR USE WITH 2 SPEAKERS.
NEVER GROUND NEGATIVE SPEAKER LEADS TO CHASSIS GROUND.
FAILURE TO WIRE EXACTLY AS SHOWN BELOW MAY CAUSE ELECTRICAL DAMAGE TO THE RADIO.
NOTE: SET CHANGER SELECTOR SWITCH ON
BOTTOM OF CHASSIS TO CORRECT
POSITION (SEE PAGE 10).
SET TO POSITION "B" FOR USE WITH
MODEL ACC-30 CHANGER.
RCA JACKS
LINE OUT
FOR USE WITH
OPTIONAL
EXTERNAL
AMPLIFIERS
RED = RIGHT
WHITE = LEFT
RADIO
B A
(BOTTOM OF RADIO)
DIN CABLE (SUPPLIED
WITH CD CHANGER).
SPE
A K ER WIRING
SPEA
SPE
A K ER WIRING
SPEA
OPTIONAL CD CHANGER
6
COMPA CT
8-PIN DIN SOCKET FOR CONNECTION TO
OPTIONAL CD CHANGER
4-PIN PLUGS
9-PIN PLUGS
LEFT FRONT SPEAKER
SEE PAGE 3 FOR
RADIO WIRING
RIGHT FRONT SPEAKER
GRAY w/BLACK STRIPE
WHITE w/BLACK STRIPE
GRAY
WHITE
GREEN
VIOLET
GREEN w/BLACK STRIPE
VIOLET w/BLACK STRIPE
HELP!
LEFT REAR SPEAKER
1-800-645-4994
Monday - Friday
Saturday
8:30am - 7:00pm Eastern
9:00am - 5:00pm Eastern
RIGHT REAR SPEAKER
4
OPER AT ING INSTRUC
INSTRUCTT IONS
OPER AT ING INSTRUC
INSTRUCTT IONS
1
ON-OFF POWER BUTTON
Press this button to turn the unit on or off.
2
VOLUME/LEVEL CONTROL
To increase the volume level, press the side of the
control. The volume will increase and the level will be
shown on the display panel from a minimum of 0 to
a maximum of 15. To increase the volume quickly,
keep the button pressed. To decrease the volume
level, press the
side of the control. Keep the
button pressed to decrease the volume quickly. This
control is also used in conjunction with the Select
button
to adjust the bass, treble, balance and
fader levels as described in , , , and .
SELECT BUTTON (SEL)
This button is used to select the audio function (bass,
treble, balance, or fade) to be adjusted using the
Level control . Pressing the Select button once will
set the unit for volume adjustment (“VOL” will appear
on the display panel). Pressing the button additional
times will select bass adjustment (“BAS” on display),
treble (“TRE”), balance (“BAL”), or fader (“FAd”).
The display will automatically return to the normal
indication 5 seconds after the last adjustment or
when another function is activated.
BASS CONTROL
To adjust the bass level, first select the Bass mode
3
3
456
2
5
4
7
3
by pressing the Select button
so the “BAS”
indication appears on the display panel. Within 5
seconds of choosing the Bass mode, press the or
side of the Level control
to adjust the bass
response as desired. The level will be shown on the
display panel from a minimum -10 to a maximum of
10 (0 indicates flat response). The display will
automatically return to the normal indication 5 seconds
after the last adjustment or when another function is
activated.
TREBLE CONTROL
To adjust the treble level, first select the Treble mode
by pressing the Select button
so the “TRE”
indication appears on the display panel. Within 5
seconds of choosing the Treble mode, press the
or
side of the Level control
to adjust the treble
response as desired. The level will be shown on the
display panel from a minimum of -10 to a maximum
of 10 (0 indicates flat response). The display will
automatically return to the normal indication 5 seconds
after the last adjustment or when another function is
activated.
LEFT/RIGHT BALANCE CONTROL
To adjust the left-right speaker balance, first select
the Balance mode by pressing the Select button
so the “BAL” indication appears on the display panel.
2
5
3
2
6
3
2
7
3
2
8
9
bl
2
bm
MANUAL UP/DOWN TUNING ( / )
To manually select a radio station, momematrily
press the Up Tuning ( ) button to advance the unit
one digit higher or the Down Tuning ( ) button to tune
downward. Pressing either button for longer than 0.5
seconds will cause the radio to tune rapidly in the
selected direction until the button is released.
AUTOMATIC SEEK TUNING (SEEK)
During radio operation, this function is used to search
for stations automatically. By pressing the button,
the radio will seek the next station and stop at that
frequency. The Seek function can be stopped by
pressing the button again or activating any other
tuning function.
LOCAL/DISTANT SELECTOR (LOC)
This feature is used to select the strength of the
signals at which the radio will stop during Automatic
Seek Tuning. Pressing the button will select the
Local setting (“LOC” will appear on the display panel)
and only strong (local) stations will be received.
Pressing the button again will select the Distant
setting (“LOC” will disappear from the display panel)
and the radio will stop at a wider range of signals,
including weaker (more distant) stations.
FM MONO/STEREO SELECTOR (M/S)
During FM radio operation, this button is used to
select mono or stereo reception of the broadcast
signal. Under normal reception conditions, the unit
should be left in the stereo mode as indicated by the
“ST” on the display panel when tuned to an FM stereo
signal. If the stereo signal is too noisy for comfortable
listening, press the FM Mono/Stereo Selector button
to switch to mono reception (the “ST” indication will
disappear from the display panel). To return to
stereo reception mode, press the button again so
that the “ST” indication appears on the display panel.
PRE-SET SCAN (PS)
AUTO-STORE TUNING (AS)
Press this button momentarily to scan the stations
pre-set into the memories on the 3 FM bands or 2 AM
bands. The unit will stop at each pre-set station for
5 seconds before continuing to the next pre-set
station (the pre-set number on the display panel will
flash during Pre-Set Scan operation). Press the
button again momentarily to stop Pre-Set Scan
bn
bo
INSTRUCTT IONS
OPER AT ING INSTRUC
Within 5 seconds of choosing the Balance mode,
press the side of the Level control to adjust the
stereo balance to the left channel speakers or the
side of the control to adjust it to the right channel
speakers. The balance position will be shown on the
display panel from “BA.L 10” (full left) to “BA.r 10” (full
right). When the volume level between the left and
right speakers is equal, “BAL 0” will be shown on the
display panel. The display will automatically return to
the normal indication 5 seconds after the last
adjustment or when another function is activated.
FRONT/REAR FADER CONTROL
To adjust the front-rear speaker balance, first select
the Fader mode by pressing the Select button so
the “FAd” indication appears on the display panel.
Within 5 seconds of choosing the Fader mode, press
side of the Level control to adjust the
the or
front-rear speaker balance as desired. The fader
position will be shown on the display panel from
“FA.r 10” (full rear) to “FA.F 10” (full front). When the
level between the front and rear speakers is equal,
“Fad 0” will be shown on the display panel. The
display will automatically return to the normal
indication 5 seconds after the last adjustment or
when another function is activated.
LOUDNESS CONTOUR (LOU)
When listening to music at low volume levels, this
feature will boost the bass and treble ranges to
compensate for the characteristics of human hearing.
Press the button to activate this feature and the
indication “LOUD” will appear on the display panel.
Pressing the button again will deactivate the feature
(the “LOUD” indication will disappear from the display
panel).
AUDIO MUTE SELECTOR (MUTE)
Press this button momentarily to mute the volume
from the system (“MUTE” will appear on the display
panel). Pressing the button again or adjusting the
Volume control
will return to the volume level
setting in use before the Mute function was activated.
AM/FM BAND SELECTOR (BND)
Each time this button is pressed, the radio band is
changed. The indications “AM1”, “AM2”, “FM1”,
“FM2” or “FM3” will appear in the display panel
according to your selection.
bp
bq
6
OPER AT ING INSTRUC
INSTRUCTT IONS
operation and remain on the selected frequency.
Pressing and holding the button for longer than 2
seconds will activate the Auto-Store Tuning feature
which will automatically scan and enter up to 6
stations into the 6 pre-set memories on the band in
use. After entering the stations into the memories,
the unit will automatically stop at each station for 5
seconds so each can be heard. If you have already
set the pre-set memories to your favorite stations,
activating the Auto-Store Tuning feature will erase
those stations and enter the new ones. This feature
is most useful when travelling in a new area where
you are not familiar with the local stations.
STATION PRE-SET MEMORIES
To set any of the 6 pre-set memories in each band,
use the following procedure:
1. Turn the radio on and select the desired band.
2. Select the first station to be pre-set using the
Manual Up/Down , or Automatic Seek Tuning
Controls.
3. Press the pre-set button to be set and continue to
hold it in for approximately 2 seconds. The pre-set
number will appear on the display panel indicating
that the station is now set into that pre-set memory
position. The station can now be recalled at any
time by pressing that button.
4. Repeat the above procedure for the remaining 5
pre-sets on that band and for the other 4 bands
on the unit.
LIQUID CRYSTAL DISPLAY PANEL
The Liquid Crystal Display (LCD) panel displays the
frequency, time, and activated functions.
NOTE: It is a characteristic of LCD panels that, if
subjected to cold temperatures for an extended
period of time, they may take longer to illuminate
than under normal conditions. In addition,
the visibility of the numbers on the LCD may
slightly decrease. The LCD read-out will return
to normal when the temperature increases to
a normal range.
CASSETTE DOOR
Hold the cassette with the exposed tape edge to the
right and insert it fully into the cassette door until the
cassette is engaged and begins playing (“PLY” will
appear on the display panel). When the cassette
reaches the end on the side of the tape being played,
the unit will automatically change direction of play as
br
bm
bs
bt
7
bn
shown by the arrow indications on the display panel.
NOTE: Observe cassette operation cautions in Care
and Maintenance section of this manual.
&
FAST-FORWARD/REWIND BUTTONS
( / )
These buttons cause the tape to move rapidly in the
direction indicated by the arrows. For example, if the
button is pushed when the tape is moving from left
to right ( on the display panel), the tape will fastforward. If the button is pressed while the tape is
moving from right to left ( on the display panel), the
tape will rewind. To stop fast tape movement, lightly
push the opposite button. If the tape is allowed to
fast-forward or rewind all the way to the end, play will
automatically begin again from that point.
PROGRAM SELECTOR
To manually reverse tape direction and play the other
side (program) of the cassette, lightly push both the
Fast-Forward and Rewind buttons
and
at the
same time. The change of direction will be shown by
the arrows on the display panel.
EJECT BUTTON ( )
Tape playback is stopped and the cassette is ejected
by pressing this button. Radio operation will
automatically resume when the cassette is ejected.
NOTE: Never leave a cassette engaged in the player
when not in use. Doing so can cause damage
to the cassette and/or mechanism of the unit.
Always press the eject button and remove
the cassette before removing the detachable
front panel.
CD CHANGER MODE SELECTOR (CD)
During radio, or tape play, press this button to select
operation of the optional CD changer as shown by
“CD-C” and “CdC” on the display panel. Refer to the
CD Changer Controls section on page 10 for specific
operating instructions.
If the button is pressed when there is no CD changer
connected to the unit, the “CD-C” and “CdC”
indications will briefly appear on the display panel.
The unit will then return to radio operation. To return
to the tape operation (if a tape is loaded in the unit),
press the button again. Durning tape play, press this
button to change to radio operation without ejecting
the tape.
TIME/FREQUENCY SELECTOR (T/F)
This unit can be set so that either the clock time or radio
bu cl
cm
bu
cn
co
cp
cl
cq
cr
3. If there is a malfunction of any of the switches on
the unit, pressing the Re-Set button may clear
the system and return to normal operation.
FRONT PANEL RELEASE BUTTON
This button is used to release the mechanism that
holds the front panel to the chassis. To detach the
front panel, press the button so that the left side of the
panel is released. Grasp the released side and pull
it off of the chassis. To re-attach the panel, position
the right side of the panel in place first and then press
the left side of the panel until the mechanism locks
it into place.
cs
NOTES ON USE OF FRONT PANEL
1. Make sure the front panel is right-side-up when
attaching it to the chassis as it cannot be attached
when up-side down.
2. Do not press very hard on the front panel when
attaching it to the chassis. No more than light to
moderate pressure should be needed.
3. When attaching the front panel, make sure the
right side is correctly engaged before pressing the
left side to lock it into position.
4. When taking the front panel with you, please use
the supplied carrying case to protect the panel from
dirt and damage. Make sure there is no dust or dirt
on the electrical terminals on the back of the panel as
this could cause intermittent operation or other
malfunctions.
OPER AT ING INSTRUC
INSTRUCTT IONS / SET T ING THE CLOCK
frequency/tape/CD changer functions will normally
appear on the display panel. Pressing the Time/
Frequency Selector button when the radio frequency,
tape or CD changer indication is shown will change
the display to show the time. The time will then be the
priority setting and the display will automatically
return to time display 5 seconds after any other radio,
tape, CD changer, or audio function display.
If the unit is set to time display priority, pressing the
Time/Frequency Selector button will change the
display to show the radio frequency/tape/CD changer
indication and this will then become the priority
setting to which the display automatically returns 5
seconds after any other function is activated.
THEFT-DETERRENT L.E.D.
Located on the chassis behind the front panel, a
light-emitting diode (L.E.D.) will flash when the panel
is removed. The flashing light serves as a visual
warning to the would-be thief that the unit has been
disabled by removal of the front panel.
RE-SET BUTTON
A Re-Set button is located on the front of the chassis
(front panel must be removed to access the button).
The re-set circuitry is provided to protect the
microprocessor circuitry and should only be activated
under the following circumstances as it will erase the
time and pre-set memories.
1. Upon initial installation after all wiring is completed.
2. After the position of the CD changer selector switch
on the bottom of the chassis has been changed.
SETTING THE CLOCK
1. Switch the vehicle ignition and radio “on”.
2. If necessary, momentarily press the Time/Frequency Selector button
display panel.
cp so that the time is shown on the
3. Press and hold the Time/Frequency Selector until the time display begins flashing. While the display is
still flashing, press the Down Tuning ( ) button to adjust the hours and then the Up Tuning ( ) button
to adjust the minutes to the correct time.
4. Five seconds after the last hour or minute adjustment is made, the time will be set in the unit and the display
will return to the normal indication.
8
SPECIFICA
NCE
SPECIFICAT
CARE
AND
MAINTENA
INTENANCE
SPECIFICATTIONS
CARE
AND
MAINTENA
INTENA
IONS // CA
RE A
ND MA
MAINTENA
INTENANCE
NCE
SPECIFICA
SPECIFICATT IONS
Size:
7” W x
178 mm x
2” H x 6” D
50 mm x 150 mm
Operating Voltage:
12 volts DC, negative ground
Output Power:
100 watts maximum (25 watts x 4 channels)
Output Wiring:
Floating-ground type designed for 4 speaker use.
The amplifiers in this unit are NOT designed for use with 2 speakers.
RCA pre-amp level outputs.
Output Impedance:
Compatible with 4 - 8 ohm speakers
Pre-Amp Output:
500 mv.
Tuning Range:
AM: 530 - 1,710 KHz. (10 KHz. step)
FM: 87.5 - 107.9 MHz. (200 KHz. step)
Sensitivity:
AM: 20 uv.
FM: 1.5 uv.
FM Stereo Separation:
30 dB
Tape Frequency Response: 50-10,000 Hz.
Tape S/N Ratio:
50 dB
Wow & Flutter:
0.15% WRMS
*Specifications are subject to change without notice.
CA
RE A
ND MA
INTENA
NCE
CARE
AND
MAINTENA
INTENANCE
The radio portion of your new sound system does not require any maintenance. We recommend you keep
this manual for future reference on how to set the clock and for general reference of the many features found
in this unit.
As with any cassette player, the cassette section of this sound system does require a minimum of
maintenance to keep it in good working condition. The following simple care and maintenance suggestions
should be followed to prevent malfunctions of the cassette system.
Cassette Care:
9
1. Purchase a cassette cleaning kit from your local retail store. Use it! At least every 20 to 30 hours
of operation you must clean the cassette mechanism. A dirty cassette player will have a poor sound.
2. Do not use cassettes that exceed 45 minutes of play on each side.
3. Do not insert a cassette that appears to be broken, twisted or dirty or with loose or torn labels on it.
4. Always keep your cassettes away from direct sunlight or exposure
to sub-freezing conditions. If a cassette is cold, allow it to warm up
before use.
5. Do not keep a cassette in the player when not in use.
6. Before inserting a cassette in the player, check that the tape is tightly
wound on the reels. Take up any excess slack using a pencil to turn
the drive hub in the cassette (see diagram).
cr
ct
cu dl
cu
dl
press the CD- button . The number of the disc in
play will be shown on the display panel.
TRACK SELECT ( / )
This button is used to quickly select the beginning of
a particular track. With each momentary press of the
Forward Track Select button ( ), the next higher
track number will be selected as shown on the display
panel. Similarly, with each momentary press of the
Backward Track Select button ( ), the next lower
track number will be selected. Pressing and holding
either button will continue to change tracks in the
selected direction.
FOWARD SEARCH (SEEK)
High-speed audible search to any forward section of
the disc can be made with this feature. Press and hold
the button to advance rapidly in the forward direction.
TRACK REPEAT PLAY SELECTOR (RPT)
When the Repeat button is pressed, the “RPT”
indication will appear on the display panel and play of
the selected track will be continually repeated until
the Track Repeat mode is canceled by pressing the
Repeat button again or by activating the Random
or Scan
functions.
TRACK SCAN SELECTOR (SCN)
When the Scan button is pressed, the “SCAN” indication
will appear on the display panel, and the first 10
seconds of each track on the disc will be played in
order. When a desired track is reached, press the
Scan button again and play of the selected track will
continue (“SCAN” will disappear from the display
panel). The Track Scan mode will also be canceled
by activating any other disc function (Track Select,
Repeat or Random).
RANDOM PLAY SELECTOR (RND)
When the Random button is pressed, the “RND”
indication will appear on the display panel and the
tracks on the disc will be played in a random, shuffled
order. The Track Select buttons
will also select
tracks in the shuffled order instead of the normal
progression. The Track Shuffle mode can be canceled
by pressing the Shuffle button again or by activating
the Repeat
or Scan
functions.
dm
dn
do
dp
dq
dp
CD CH
A NGER CONTR
OL
S / ERR
OR CODE
CHA
CONTROL
OLS
ERROR
CD CH
A NGER CONTR
OL
S
CHA
CONTROL
OLS
Built into this radio are controls to operate an optional
CD changer. Please check with your Rampage/
Audiovox car stereo specialist for recommendations
of the models that will work with this radio.
IMPORTANT: The CD Changer Selector Switch on the
bottom of the chassis must be set to the correct
position to match the type of changer being used with
this radio. The Re-Set button should then be pressed
to activate the change of position. If you are not sure of
the correct switch position for your model of CD changer,
please check with your Rampage/Audiovox retailer or
contact us directly at 1-800-645-4994.
NOTE: Switch position for model ACC-30 changer
is "B".
Adjustment of the audio functions (volume, tone,
balance, and fader) for the CD changer operate in the
same manner as they do for radio play. The following
controls will operate the CD changer when it is
installed and connected to this radio. Refer to the
owner’s manual included with the CD changer for
instructions on the installation and correct loading
and use of the CD magazine.
CD CHANGER MODE SELECTOR (CD)
PAUSE/PLAY SELECTOR ( II )
During radio, or tape play, press this button to select
operation of the CD changer as shown by “CD-C” and
“CdC” on the display panel. Disc play will begin and
the disc and track number will be shown on the display
panel. If a new magazine has been loaded into the
changer, play will begin from the first track of the first
disc in the magazine. If a magazine was already in the
changer, play will resume from the track on the disc
previously in play.
During CD changer play, pressing this button once will
return to the radio operation. Pressing again will
change to tape play if a tape is loaded in the unit or
back to CD changer if no tape is loaded.
&
DISC SELECT (CD+ & CD-)
These buttons are used to select the desired disc for
play. To advance to a higher number disc, press the
CD+ button . To return to a lower number disc,
dq
dm
do
dp
CD CH
A NGER ERR
OR CODE
CHA
ERROR
If a problem should develop while operating the CD changer, the error code “Err” may appear on the display
panel. This can indicate a number of problems with the unit, including a mechanical error or an error in the
microprocessor control of the changer. If the error code should appear, try ejecting and re-loading the magazine
into the changer. While the magazine is out of the changer, make sure the discs are clean, undamaged, and
loaded correctly (see Owner’s Manual of the CD changer). You may also try activating the Re-Set button
on the unit, but this will also erase the time and pre-set memories.
If the suggested measures do not solve the problem, contact an approved warranty station near you for further
assistance.
cr
10
12 MONTH LIMITED WARRANTY
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product
that should this product or any part thereof, under normal use and conditions, be proven defective
in material or workmanship within 12 months from the date of original purchase, such defect(s) will
be repaired or replaced with new or reconditioned product (at the Company's option) without charge
for parts and repair labor.
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with
proof of warranty coverage (e.g. dated bill of sale), specification of defect(s), transportation prepaid,
to the warranty center at the address shown below.
This Warranty does not extend to the elimination of car static or motor noise, to correction of antenna
problems, to costs incurred for installation, removal, or reinstallation of the product, or damage to
tapes, compact discs, speakers, accessories, or vehicle electrical systems.
This Warranty does not apply to any product or part thereof which, in the opinion of the Company,
has suffered or been damaged through alteration, improper installation, mishandling, misuse,
neglect, accident, or by removal or defacement of the factory serial number/bar code label(s). THE
EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE
REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S
LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO THE
DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY
HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE
BROUGHT WITHIN A PERIOD OF 30 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO
CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED,
WHATSOEVER. No person or representative is authorized to assume for the Company any liability
other than expressed herein in connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or
limitation of incidental or consequential damage so the above limitations or exclusions may not apply
to you. This Warranty gives you specific legal rights and you may also have other rights which vary
from state to state.
U.S.A. : AUDIOVOX CORPORATION, 150 MARCUS BLVD., HAUPPAUGE, NEW YORK 11788 l 1-800-645-4994
CANADA: CALL 1-800-645-4994 FOR LOCATION OF WARRANTY STATION SERVING YOUR AREA
128-4270E
© 1999 Audiovox Corporation
l
Hauppauge, NY 11788
Printed in China
128-5567A
Download PDF

advertising