Operating instructions | Audiovox AV-970 Car Stereo System User Manual

INDEX
How To Use This Manual
Kit Information
Page 1
Page 2
,
Universal and Impor1 Car Installations
Chevrolet -Oldsmobile-Pontiac-Bu
ick -G MC-Cadillac-Satu
Installations
Ford-Lincoln-Mercury
Installations
Chrysler-Dodge-Plymouth
Installations
Radio Wiring
Speaker Wiring- 2 Speaker Systems
4 Speaker Systems
Pages 3,4
m
Pages 5,6
Pages 7,8
Page 9
Page 10
Page 11
Page 12
Operating Instructions
Specifications
Troubleshooting
Care and Maintenance
Warranty
Pages 13,14
Page 15
Page 16
Page 17
Back Cover
Toll-Free Assistance
The installation and wiring connections for this unit are so simple, we doubt you'll need our
help, but, if you do, we're here to help you. Just call our toll-free telephone assistance line at
(800) 645- 7102 during days/hours shown.
TIME
DAY
MON.-FRI.
SATURDAY
I
MOUNTAIN
PACIFIC
15:30AM
-4PM
6AM-2PM
6:30AM -5PM
7AM -3PM
-ZONE
EASTERN
CENTRAL
7:30AM
-6PM
BAM-4PM
8:30AM
-7PM
9AM-5PM
HOW TO USE THIS MANUAL
1. Identify the make and year of the car in which you will be installing this sound system.
2. Refer to the Kit Listing and Kit Information sections on page 2 to determine if a kit is required.
3. If a kit is required, follow the directions in Kit Information section.
4. Follow the specific installation instructions for your particular make of car as listed in the index.
KIT INFORMATION
1. The years shown in the Kit Listing below are approximate. Always check the application chart at your
retail store to find information on your specific make, model, and year of vehicle. If a kit is required, read
the description on the kit you intend to purchase to make sure it applies to your vehicle. If you have
any doubts or questions, call our toll-free "HELP" line.
2. The kits shown below are Audiovox kits. Your retailer may sell kits made by other manufacturers which
may also be usable to install this radio. Always check the kit application before purchasing it to make
sure it will work with your vehicle.
3. If you believe you need a kit but cannot find a retail store where it is available, call our toll-free "HELP"
line.
KIT LISTING
VEHICLE TYPE
C h evrolet -0 Ids mob ile- Bu ic k- Pontiac-Cadi lIac-Satu rn
1981 and Older
1982 and Newer
Chevrolet-GMC Full Size Vans
1987 and Older
1988 and Newer
Chevrolet-GMC Full Size Pickups
1987 and Older
1988 and Newer
Ch rysler -Dodge- Plymouth
U.S. Built 1974 and Newer
Imported
Ford-Lincoln-Mercury
1984 and Older
1985 through 1990
1991 and Newer
AMC-Jeep-Eagle
1971 and Newer
:
KIT REQUIREMENT/NOTES
No Kit Required
AX-93-FCGM
No Kit Required
AX-88-CHV
No Kit Required
AX-88-CHT
AX-93-FCGM
Refer to In-Store Chart
No Kit Required
AX-93-FCGM
AX-88-SNP
:
No Kit Required
Due to the wide variety of import cars and the different installations required, this manual does not show
specific installations in these vehicles. However, this sound system can be installed in many import cars
by following the "Universal Installation" section on pages 3 and 4. Check the application chart at your retail
store or call our toll-free "HELP" line for specific information on your particular car.
IMPORTS:
Ac u ra -Aud i-BMW -Daihatsu-Fiat -Honda -Hyu ndai
Me rcedes- Peug eot -Porsche-Saab-Subaru
Volkswagen-Volvo-Yugo
Will Fit Most Years; Some Require AX-88-SNP Kit
Datsun-Nissan (Most Models)
1982 and Newer
Will Fit Most Years; Some Require AX-88-NAB Kit
Mazda (Most Models)
1986 and Newer
Will Fit Most Years; Some Require AX-87-MAZ Kit
T oyota (Most Models )
1982 and Newer
Will Fit Most Years; Some Require AX-88- TOY Kit
* Refer to In-Store Chart to determine if kit is required.
For vehicles not listed or more specific information, refer to the in-store application chart or call our "HELP"
line.
~
f
*
*
*
*
UNIVERSAL
INSTALLATION
FOR VEHICLES
WITH AN EXISTING
RADIO
OPENING
This installation is designed for cars, trucks, vans, and boats that have an existing radio opening. It can also be used
as an option on some of the vehicles listed as requiring the AX-88-SNP kit. It will not work on all vehicles, but can be
used on most newer Fords and many imports.
1. Inspect Ole Existing Radio Opening:
A. Use the trimplate supplied with the radio to cover the existing opening. If it completely covers the opening, you
can install the radio as explained below. If it does not cover the opening, you will need an installation kit.
B. Check that there will be sufficient space behind the dashboard for the radio chassis.
2. Wire the Radio to the Vehicle's Wiring:
A. In most cases it is easier to wire the radio before mounting it. Place the radio near the dashboard so the wires
can be led through the opening.
B. Carefully follow the diagrams on pages 10 and 11 or 12 (depending on how many speakers you are using) to
wire the radio, making certain all connections are secure and insulated with wire nuts or electrical tape to insure
proper operation of the unit.
C. After completing the wiring, turn the unit on to confirm operation (ignition switch must be "on"). If unit does not
operate, re-check all wiring until problem is corrected. Once proper operation is achieved, turn off unit and
ignition switch, and proceed with final mounting of the radio
3.
Mounting Ole Radio:
A. Thread a shaft nut half-way down each radio shaft.
B. Place a metal back-up plate on each radio shaft against the shaft nut.
C. Position the radio behind the dashboard opening so that the back-up plates are snug against the back of the
opening. Adjust the shaft nuts behind the back-up plates so that the desired amount of radio extends through
the opening. If possible, the best appearance is usually achieved when there is enough of the radio extending
to be flush with the front of the trimplate.
D. Place the trimplate over the front of the radio and secure it with a shaft nut on each radio shaft.
E. Attach one end of the perforated support strap (supplied) to the screw stud on the radio using the hex nut
provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below
the radio using the screw and nut provided. Bend the strap to position it as necessary.
CAUTION: The rear of the radio m.Y.§J.
be supported with the strap to prevent damage to the dashboard from the
weight of the radio or improper operation of the radio due to vibration.
F. Install knobs on radio shafts.
UNIVERSAL
INSTALLATION
FOR VEHICLES
WITHOUT
AN EXISTING
RADIO
OPENING
This installation is designed for cars, trucks, vans, and boats that do not have an existing radio opening. It will require
cutting an opening in a surface of the vehicle, so it is important to mark and measure carefully.
1. Select III. ...nUng
Area:
A. Using the trimplate supplied, verify that there will be sufficient space on the selected mounting surface.
B. Check that there will be sufficient space behind the dashboard for the radio chassis.
2. Cut tIle Req.ired Opening:
A. Using the trimplate as a template, place it on the selected mounting surface and mark the 2 shaft holes and
nosepiece opening that will need to be cut.
B. Carefully cut the 3 holes using a drill and keyhole saw as appropriate. File edges of the openings to remove
any burrs.
3.
tIle bdi. to III. V.hlc.."s Wktng:
A. In most cases it is easier to wire the radio before mounting it. Place the radio near the dashboard so the wires
can be led through the opening.
B. Carefully follow the diagrams on pages 10 and 11 or 12 (depending on how many speakers you are using) to
wire the radio, making certain all connections are secure and insulated with wire nuts or electrical tape to insure
proper operation of the unit.
C. After completing the wiring, turn the unit on to confirm operation (ignition switch must be "on"). If unit does not
operate, re-check all wiring until problem is corrected. Once proper operation is achieved, turn off unit and
ignition switch, and proceed with final mounting of the radio.
4. ...80..
tIle ndi8:
A. Thread a shaft nut half-way down each radio shaft.
B. Place a metal back-up plate on each radio shaft against the shaft nut.
C. Position the radio behind the dashboard opening so that the back-up plates are snug against the back of the
opening. Adjust the shaft nuts behind the back-up plates so that the desired amount of radio extends through
the opening. If possible, the best appearance is usually achieved when there is enough of the radio extending
to be flush with the front of the trimplate.
D. Place the trimplate over the front of the radio and secure it with a shaft nut on each radio shaft.
E. Attach one end of the perforated support strap (supplied) to the screw stud on the radio using the hex nut
provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below
the radio using the screw and nut provided. Bend the strap to position it as necessary.
CAUTION: The rear of the radio ~
be supported with the strap to prevent damage to the dashboard from the
weight of the radio or improper operation of the radio due to vibration.
F. Install knobs on radio shafts.
CHEVROLET
1981
AND
-OLDSMOBlLE-BUICK-PONTIAC-GMC-CADILLAC
INSTALLATION
OLDER
ImQortant- This installation is designed for 1981 and older U.S. made GM cars, trucks, and vans. For 1981 and newer
vehicles, an installation kit may be required. See Kit Listing on Page 2 of this manual or refer to the in-store application
chart. If a kit is not required, use the following instructions.
1. Remove Existing Radio:
A. Remove radio knobs and shaft nuts behind the knobs.
B. Locate and remove support brace at back of radio.
C. Push radio back into dashboard to access the wiring and antenna cables plugged into the rear of the chassis.
D. Un-plug the wiring harness(es) and antenna cable and remove the radio.
2. Wire the le. Radio:
A. In most cases it is easier to wire the radio before mounting it. Place the radio near the dashboard so the wires
can be led through the opening.
B. Carefully follow the diagrams on pages 10 and 11 or 12 (depending on how many speakers you are using) to
wire the radio, making certain all connections are secure and insulated with wire nuts or electrical tape to insure
proper operation of the unit.
C. After completing the wiring, turn the unit on to confirm operation (ignition switch must be "on.). If unit does not
operate, re-check all wiring until problem is corrected. Once proper operation is achieved, turn off unit and
ignition switch, and proceed with final mounting of the radio.
3. Install the le. Radio:
A. Thread a shaft nut half-way down each radio shaft.
B. Trim the top edge off of the nosepiece collar at the "CUT OFF FOR GM" mark and place the collar on radio
nosepiece.
C. Place the radio behind dashboard and through the radio opening. Adjust the position of the shaft nuts so that
the radio nosepiece and collar are flush against the back of the dashboard.
D. Secure the radio with a shaft nut on each radio shaft.
E. Attach one end of the perforated support strap (supplied) to the screw stud on the radio using the hex nut
provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below
the radio using the screw and nut provided. Bend the strap to position it as necessary .
CAUTION: The rear of the radio my§! be supported with the strap to prevent damage to the dashboard from the
weight of the radio or improper operation of the radio due to vibration.
F. Install knobs on radio shafts.
CHEVROLET
1982
AND
-OLDSMO
BILE-
BUICK
-PONT
IAC-
GMC-CADILLAC-SATU
INSTALLATION
NEWER
ImRortant- This installation is designed for most 1982 and newer GM cars, trucks, and vans where an installation kit
is required. See Kit Listing on Page 2 of this manual or refer to the in-store application chart. If a kit is not required,
use the instructions on Page 5.
1. R...V8
Existing Radio:
A. Remove the existing dashboard trimpanel surrounding the radio opening. This panel is usually secured by
screws and/or snap-in clips.
B. Remove the screws used to secure the radio to the sub-dashboard.
C. Pull the radio forward to access the wiring and antenna cables plugged into the rear of the chassis.
D. Un-plug the wiring hamess(es) and antenna cable and remove the radio.
.,
;:!
~
2. 18sta11the I..
Radio:
A. Follow the instructions included with the installation kit to attach the radio to the mounting plate supplied with
the kit.
B. Place the radio near the dashboard so the wires can be led through the opening and following the instructions
of Step 2 on Page 5, carefully wire the radio making certain all connections are secure and insulated and confirm
proper operation.
C. Install the radio/mounting plate assembly to the sub-dashboard according to instructions of installation kit.
D. Attach one end of the perforated support strap (supplied) to the screw stud on the radio using the hex nut
provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below
the radio using the screw and nut provided. Bend the strap to position it as necessary.
CAUTION: The rear of the radio .!!l.Y.§.t
be supported with the strap to prevent damage to the dashboard from the
weight of the radio or improper operation of the radio due to vibration.
E. Replace the dashboard trimpanel.
F. Install knobs on radio shafts.
FORD-LINCOLN-MERCURY
INSTALLATION
-1984
AND
OLDER
ImQortant- This installation is designed for 1984 and older U.S. made Ford cars, trucks, and vans. For newer
vehicles, an installation kit may be required. See Kit Listing on Page 2 of this manual or refer to the in-store chart.
1. Renlove Existing Radio:
A. Remove radio knobs and shaft nuts behind the knobs.
B. Locate and remove support brace at back of radio.
C. Push radio back into dashboard to access the wiring and antenna cables plugged into the rear of the chassis
Do Un-plug the wiring harness(es) and antenna cable and remove the radio.
2. Wire the le. Radio:
Ao In most cases it is easier to wire the radio before mounting it. Place the r~dio near the dashboard so the wires
can be led through the opening.
B. Carefully follow the diagrams on pages 10 and 11 or 12 (depending on how many speakers you are using)
to wire the radio, making certain all connections are secure and insulated with wire nuts or electrical tape to
insure proper operation of the unit.
C. After completing the wiring, turn the unit on to confirm operation (ignition switch must be Non"). If unit does
not operate, re-check all wiring until problem is corrected. Once proper operation is achieved, turn off unit
and ignition switch, and proceed with final mounting of the radio.
3. Install the I..
Radilo:
A. Thread a shaft nut halfway down each radio shaft.
B. Place the nosepiece collar on the radio nosepiece.
C. Place the radio behind dashboard and through the radio opening. Adjust the position of the shaft nuts so that
the radio nosepiece and collar are flush against the back of the dashboard.
D. Secure the radio with a shaft nut on each radio shaft.
E. Attach one end of the perforated support strap (supplied) to the screw stud on the radio using the hex nut
provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below
the radio using the screw and nut provided. Bend the strap to position it as necessary.
CAUTION: The rear of the radio mY§.t be supported with the strap to prevent damage to the dashboard from the
weight of the radio or improper operation of the radio due to vibration.
F. Install knobs on radio shafts.
l
FORD-LINCOLN-MERCURY
ImRortant-
This
installation
kit is required
chart.
INSTALLATION
installation
forthese
For 1991 and newer
theAX-88-SNP
is designed
vehicles.
vehicles,
kit. Instructions
for most
-1985
1985
AND
through
1990
NEWER
U.S.
made
See Kit Listing on Page 2 of this manual
the radio can be installed
for use oftheAS-88-SNP
as shown
kit are included
Ford
cars,
and
vans
or refer to the in-store
on Page 3 of this manual
with the kit and are not shown
and
an
application
or you can use
inthis
manual.
1. Remove Existing Radio:
A. Remove existing dashboard trim panel surrounding the radio opening. This panel is usually secured by screws
and/or snap-in clips.
B. Remove the screws used to secure radio to the sub-dashboard.
C. Pull the radio forward to access the wiring and antenna cables plugged into the rear of the chassis.
D. Un-plug the wiring harness(es) and antenna cable and remove the radio.
2. Install the le. Radio:
A. Follow the instructions included with the installation kit to attach the radio to the mounting plate supplied with
the kit.
B. Place the radio near the dashboard so the wire can be led through the opening and following the instructions
of Step 2 on Page 7, carefully wire the radio making certain all connections are secure and insulated and
confirm proper operation.
C. Install the radio/mounting plate assembly to the sub-dashboard according to instructions of installation kit.
D. Attach one end of the perforated support strap (supplied) to the screw stud on the radio using the hex nut
provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above orbelow
the radio using the screw and nut provided. Bend the strap to position it as necessary.
CAUTION: The rear of the radio mY..$.lbe supported with the strap to prevent damage to the dashboard from the
weight of the radio or improper operation of the radio due to vibration.
E. Replace the dashboard trimpanel.
F. Install knobs on radio shafts.
CHRYSLER-DODGE-PLYMOUTHINSTALLATION
ALL
U.S.
MADE
CARS,
TRUCKS,
AND
VANS
BUILT
SINCE
1974
ImRortant- This radio cannot be installed in any U.S. made Chrysler, Dodge, or Plymouth vehicle without an
installation kit. Refer to the Kit Listing on Page 2 for the required kit. Complete kit installation is explained in the
instructions included with the kit.
A. Remove the existing dashboard trimpanel surrounding the radio opening. This panel is usually secured by
screws and/or snap-in clips.
B. Remove the two large screws used to secure radio to the sub-dashboard.
c. Pull the radio forward to access the wiring and antenna cables plugged into the rear of the chassis.
D. Un-plug the wiring harness(es) and antenna cable and remove the radio.
2. Install the lew Radio:
A. Follow the instructions included with the installation kit to attach the radio to the mounting plate supplied with
the kit.
B. Place the radio near the dashboard so the wires can be led through the opening and following the instructions
of Step 2 on Page 3, carefully wire the radio making certain all connections are secure and insulated and
confirm proper operation.
C. Install the radio/mounting plate assembly to the sub-dashboard according to instructions of installation kit.
D. Attach one end of the perforated support strap (supplied) to the screw stud on the radio using the hex nut
provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above orbelow
the radio using the screw and nut provided. Bend the strap to position it as necessary.
CAUTION: The rear of the radio mY§l be supported with the strap to prevent damage to the dashboard from the
weight of the radio or improper operation of the radio due to vibration.
E. Replace the dashboard trimpanel.
F. Install knobs on radio shafts.
I~
I
b.
RADIO
WIRING
REFER TO PAGE 11 OR 12 FOR SPEAKER WIRING
SPEAKER
WIRING
REFER TO PAGE 10
FOR RADIO WIRING
-2
SPEAKER
SYSTEMS
I
~I
SPEAKER
WIRING
-4
SPEAKER
REFER TO PAGE 10
FOR RADIOWIRING
I
SYSTEMS
OPERATINGINSTRUCTIONS
CD ON-OFF SWITCHNOLUME CONTROL
Turn this knob to the right to turn the unit on.
Continue rotation until the desired volume
level is obtained.
<V LEFT/RIGHT BALANCE CONTROL
Turn this knob to the left or right to obtain the
desired balance between left and right speakers.
@ TONE CONTROL
Turn this knob either to the left or right to
obtain the desired tone response. Turn it to
the right to increase the treble or to the left to
increase the bass.
@ AM/FM BAND SELECTOR
Each time this button is pressed, the radio
band changes. According to your selection,
the selected radio band indicator appears on
the display panel.
@ LOCAL-DIST ANT SWITCH
This two position switch is incorporated to allow
maximum reception in both weak and strong
FM signal areas. When tuned to a weak
(distant) station, push the switch in. This will
allow maximum signal to the receiver. When in
an extremely
strong
signal
area
(local),
signals.
1
...
release
the switch. This will eliminate all weak signals
and suppress overly strong signals so as to
avoid overloading the receiver input. When
moving out of a strong signal area, return the
switch to the "distant" position.
Note: The Local-Distant
t
switch only affects FM
I
I
I
I
"'
"'
@) MANUAL TUNING CONTROL
Turn the knob either to the left or the right to
select a radio station .
CD ANTENNA TRIMMER
It is very important to adjust the ANTENNA
TRIMMER for optimum AM reception. The antenna trimmer is located at the back in the tape
slot. Tune in a weak station around 1400 KHz
and adjust the trimmer with a small screwdriver
for maximum output.
Note: Antenna trimmer is for AM band only and
has no effect on FM band.
@ DISPLAY PANEL
Displays frequency as well as indicators for
AM, FM, stereo reception (ST) and tape player
operation (TP).
I
~
@ CASSETTE SLOT
Hold a cassette with the exposed tape edge to
the right, then insert into the cassette slot.
Depress fully until the cassette is engaged and
begins playing. When the cassette reaches the
end of play, the unit will automatically change
over to radio operation.
Note: Observe cassette operation cautions in
Care and Maintenance
section of this manual.
j
I"
11
I
~
~
~
ji
I
,
@ FAST-FORWARD/EJECT
BUTTON
This button performs two functions. To eject a
cassette, simply depress this button fully then
release. The cassette will eject and radio
operation will resume. To fast-forward the
tape, depress the button half-way in to the
locked position. To stop fast-forward and resume normal tape playback, depress the button slightly and release. Do not press fully in or
the cassette will be ejected.
~~
SPECIFICATIONS
Size:
7" W
178mm
x
2" H
x 50mm
x
5" D
x
125mm
Operating Voltage:
12 volts DC, negative ground
Output Power:
14 watts maximum
( 7 watts x 2 channels)
Output Wiring:
Common-ground
type designed for 2 speaker
May also be used with 4 speakers.
Output Impedance:
Compatible with 4-8 ohm speakers
Tuning
AM: 530-1,620 KHz.
FM: 87.5-107.9 MHz.
Range:
AM: 15 uv.
FM: 2.5 uv.
Sensitivity:
FM
Stereo
Separation:
30dB
Tape Frequency Response:
50-10,000 Hz.
Tape SIN Ratio:
SOdB
Wow & Flutter:
0.25%
* Specifications
are
WRMS
subject
to change
without
notice.
use.
PROBABLE CAUSE
PROBLEM
Unit completely
inoperative
no lights,
Incorrect power connection
CHECK FOLLOWING
i Orange/White stripe wire to +12V ACC.
Green/White stripe wire to + 12V
I and
battery
no sound
Unit will not keep time or Radio
station memory
(Electronic Tuning Radios Only)
Noise
on
both
radio
and
Blown fuse
Check fuses in wires listed above and
check car fuse block
Incorrect power connection
Green/White Stripe wire is not connected to a 'live' + 12V battery source
Blown fuse
Check fuse in Green/White
and at car's fuse block
Poor ground
Check
Noise on radio only
wire for
Dir1y or corroded battery posts
Clean and tighten connection
If problem also existed with previous
radio you removed
Consult your local garage mechaniccar may need tune-up or noise filter
Antenna
Check that antenna base is grounded.
Test with antenna disconnected.
If
noise goes away, replace antenna
Poor FM reception
AM reception
and almost no
Antenna
Poor FM reception
and Good AM
FM Local-Distant
Replace
switch
I
I
reception
No sound on one speaker
(both radio and tape)
stripe
proper grounding
tape
I
Black/White
stripe wire
Wirinq
Speaker
antenna
and antenna
cable
Check if unit has a Local-Distant switch
and set to "Distant" position
Check speaker wiring
T est
with
good
speaker
RaCIio Operation
Check balance
-~- and fader controls
Poor sound on tape only (after one
month or more of tape usage)
Poor sound-new
unit
Dirty tape mechanism
Clean tape head and mechanism
For radios with 40 watts or more
Check rating of speakers for sufficient
output power
power capacity
I Check that speakers are in good
condition
Check that Violet and Green speaker
wires are not grounded
For all radios
Check speaker wiring
CARE AND MAINTENANCE
The radio por1ion of your new sound system does not require any maintenance. We recommend you keep
this manual for general reference of the many features found in this unit.
As with any cassette player, the cassette section of this sound system does require a minimum of
maintenance to keep it in good working condition. The following simple care and maintenance suggestions
should be followed to prevent malfunctions of the cassette system.
Cassette Care:
1. Purchase a cassette cleaning kit from your local retail store. Use it! At least every 20 to 30 hours
of operation you must clean the cassette mechanism. A dirty cassette player will have a poor sound.
2. Do not use cassettes that exceed 45 minutes of play on each side.
3. Do not insert a cassette that appears to be broker, twisted or dirty or with loose or torn labels on it.
4. Always keep your cassettes away from direct sunlight or exposure to sub-freezing conditions. If a
cassette is cold, allow it to warm up before use.
5. Do not keep a cassette in the player when not in use.
6. Before inserting a cassette in the player, check that the tape is tightly wound on the reels. Take up
any excess slack using a pencil to turn the drive hub in the cassette (see diagram below).
12
Applies
to In-dash
radios,
MONTH
radio/tape
LIMITED
pla)'erand
WARRANTY
radio/CD
pla)'ercombinations,
and CD Changers.
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this
product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within
12 months from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned
product (at the Company's option) without charge for parts and repair labor.
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty
coverage (e.g. dated bill of sale), specification of defect(s), transportation prepaid, to an approved warranty station.
For the location of the nearest warranty station to you, call toll-free to our control office:
IN U.S.A.
IN CANADA
(800) 243-1311
(800) 461-1772
This Warranty does not extend to the elimination of car static or motor noise, to correction of antenna problems, to
costs incurred for installation, removal, or reinstallation of the product, or damage to tapes, compact discs, speakers,
accessories, or vehicle electrical systems.
This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or
been damaged through alteration, improper installation, mishandling, misuse, neglect, accident, or by removal or
defacement of the factory serial number/barcode label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER
THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT,
SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE
PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY
IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS wRmEN
WARRANTY.
ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED
WARRANTY OF MERCHANTABILITY
MUST BE BROUGHT WITHIN A PERIOD OF 30 MONTHS FROM DATE
OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED,
WHATSOEVER.
No person or representative is authorized to assume for the Company any liability other than
expressed herein in connection with the sale of this product.
Some
states
do not
or consequential
specific
U.S.A.
legal
rights
limitations
so the
and
: AUDIOVOX
CANADA:
ZEALAND:
you
may
on how
above
also
CORPORATION,
AUDIOVOX
AUSTRALIA:
NEW
allow
damage
CANADA
AUDIOVOX
PACIFIC
AUDIOVOX
long
an implied
limitations
have
other
rights
150 MARCUS
LTD.,
DOYLE
PTY L TD.,
which
BLVD.,
MISSISSAUGA,
PTY L TD.,
PACIFIC
warranty
or exclusions
UNIT
lasts
may
vary
HAUPPAUGE,
ONTARIO.
AVENUE,
not
from
or the
exclusion
apply
to you.
state
NEW
(800)
of incidental
Warranty
gives
you
to state.
YORK
11788
.(800)
243-1311
461-1772
UNANDERRA,
B, 6 HENDERSON
or limitation
This
NSW
PLACE,
2526
PENROSE,
.(042)
718-555
AUCKLAND.(09)
645-720
FonD No. 128-4123C ~
AUDIOVOX
@ 1995
Audiovox
@
Corporation.
150
Marcus
Blvd
.Hauppauge,
NY
11788
Printed
in
China
Form No 12S;4421C
Download PDF

advertising