Owner`s manual | Audiovox AVD400T Car Stereo System User Manual

R
AVD 400T
C
2004 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y.11788
128 - 7109
21
A . Welcome
H. Specification
Supported media
Signal format system
DVD Video format
Video output
Audio output
Signal-to-noise ratio
Harmonic distortion
Dynamic range
Wow and flutter
Power source
Power consumption
Operating temperature
Storage temperature
Operating humidity
Dimensions (W x H x D)
Weight
DVD / CD / MP3/ JPEG CD-R
NTSC/PAL
Horizontal 720 pixel,
vertical 480 pixel
1.0 Vp-p/75 Ohm
1.2 V to 1.8 V
More than 60 dB
Less than 60 dB
More than 70 dB
Beyond measurable Limits
DC 12 V Regulated
Less than 1W in stand-by mode;
and less than 12W in use
0 C (32 F) to +40 C (104 F)
-20 C (-4 F) to +60 C (140 F)
5% to 95%
7 x 2 x 7.3 inches
(178 x 50 x 186 mm)
3 lbs (1.6 kg)
Thank you for choosing the AVD400T DVD Player. The AVD400T is
designed to optimize the enjoyment of your favorite DVDs in the mobile environment. This DVD Player is constructed to provide years of
reliable, trouble-free service. Please read this manual thoroughly prior to
operating the player and save it for future reference.
B. Precautions
EXPLANATION OF GRAPHIC SYMBOLS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER OR BACK. NO USER - SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
The lighting flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
dangerous voltage within the products enclosure that may be
of sufficient magnitude to constitute risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS DEVICE TO MOISTURE.
20
1
IMPORTANT NOTICE
An LCD panel and/or video monitor may be installed in a motor vehicle and
visible to the driver if the LCD panel or video monitor is used for vehicle
information, system control, rear or side observation or navigation. If the
LCD panel or video monitor is used for television reception, video or DVD
play, the LCD panel or video monitor must be installed so that these features
will only function when the vehicle is in"park" or when the vehicle's parking
brake is applied.
An LCD panel or video monitor used for television reception, video or DVD
play that operates when the vehicle is in gear or when the parking brake is
not applied must be installed to the rear of the driver s seat where it will
not be visible, directly or indirectly, to the operator of the motor vehicle.
1. OBJECT AND LIQUID
Do not insert objects of any kind into the system through its openings;
do not spill or spray liquid on or into the system (this may result in a
fire or electric shock). Do not place heavy objects on the unit. To ensure
proper ventilation and proper operation, never cover or block the slots
and openings.
2. DISASSEMBLE
Do not attempt to disassemble the unit. There is a risk of electric shock
and/or exposure to Laser Radiation. Contact qualified service personnel
if your system is in need of repair.
HOW TO WATCH TV
Press the Mode button to go to the TV mode. Active channels can be auto stored
by pressing STOP ( MEMORY) B button.
Select the channels you want by pressing NEXT (CH+)
(CH-) D button (see page 14 remote controller picture).
button or PREVIOUS
Note: Channels may not be selectable if in a bad RF signal area.
ADD/DEL
Use this function to delete or memorize a channel you want.
Select the channel you want by pressing the number buttons and add or
erase the channel by pressing ENTER (ADD/DEL) A button.
Remote Control:
A
Enter
/Add
B
/CH+
C
/CH-
D
3. CLEANING UNIT
When cleaning, make sure the system is unplugged from the power
source. Do not use any solvents or cleaning materials. Clean the DVD
player using a lightly dampened lint free cloth to wipe the unit.
2
C
19
4) Select Rating by using the LEFT/RIGHT buttons, press ENTER
to enter the Rating set up page.
Language
Video
Audio
Password
Rating
Rating
------&. Asult
Load Factory
Rating
Reset
Display
4. DISC
Do not use irregularly shaped discs such as heart or star-shaped discs
as they may cause the unit to malfunction. Do not stick paper ,tape or
glue on the disc. Do not expose the disc to direct sunlight or heat sources. Do not touch the surface of the disc. Handle the disc by its edges.
Clean the disc by wiping the disc from the center out with a soft lint free
cleaning cloth. Remove the disc from the unit and store it in its case after
playing. Some playback operations of discs may be intentionally fixed
by software producers .The AVD400T plays discs according to the disc
contents the software producers designed therefore some playback
features may not be available. Refer to the instructions supplied with the
discs.
Select Password using the UP/DOWN buttons. For first time use
the default password 3308 to unlock the unit. Select Rating using
the UP / DOWN buttons and press ENTER to enter the submenu.
Select the rating level you desire by repeatedly pressing the ENTER
button .Use the UP button to return to Password and input either
the default password or any new 4 digit password and press ENTER.
5. Powering the DVD Player
This system MUST be powered from switched (Accessory) power as
indicated on the marking label. Power should be applied to the unit when
the ignition key is in the Run and/or Accessory position. Use only the
supplied power cable provided with this set to avoid electric hazards.
Rating:1.Kid Safe 2.G 3.PG 4.PG-13
5.PG-R 6.R 7.NC-17 8.Adult
6. Operation
When the temperature rises dramatically from a very low temperature,
moisture may condense inside the AVD400T and cause the DVD player
to malfunction. If the AVD400T does not operate properly under these
conditions leave the AVD400T turned on for at least 30 minutes for the
moisture to evaporate.
NOTE: For 1st time use the default password is 3308.
NOTE: The Default Password is 3308. This password is always
effective even after you have selected your own password and
changed it. To avoid the possibility of others using the default
password to set the parental level and change the password, you
can record this default password in another area and delete it
from this manual. Some discs can be limited depending on the
age of users while some discs can not.
Restore Default: To restore all of the options to the default settings
select RESTORE DEFAULT using the UP/DOWN buttons and
press ENTER . This will return all of the settings except parental to
the default settings.
18
3
Lpcm 48k DS Display
b. Select ' LPCM ' using the UP/DOWN buttons, then press ENTER
to enter the submenu. Select the digital output you desire using the
UP/DOWN buttons, then press ENTER to confirm the setting.
C. Contents
1. 1 Main Unit
2. 1 Remote control with one Battery (CR2025)
3. 1 12VDC Power Harness
4. 2 Brackets with 4 Screws
5. 1 Remote IR Receiver
6. 1 AV cable (RCA to RCA)
7. 1 AV cable (1/8 to RCA)
1
8. 1 Owner's Manual
9. 4 Stick-on Rubber Feet
2
3
Language
Video
Digital out
Lpcm 48k DS
Audio
RAW
Off
Off
On
9
4
5
6
14
13
7
8
D. Controls
Main Unit (Refer to Figure 1)
1. Power Button
2. Previous Button
3. Next Button
4. Mode Button
5. Remote Control Sensor
6. Stop /Play /Pause Button
7. A/V 2 Audio Input Jack
8. A/V 2 Video Input Jack
9. Eject Button
10. IR Input
11. A/V 1 Input Jacks
12. Digital Audio Output
13. Audio R Output Jack
14. Audio L Output Jack
15. Video Output Jack
16. S-Video Output Jack
17. DC In/Out 12V Power Supply Connector
18. DC In/Out 12V Power Supply Connector
19. TV-RF Input Jack
18
12
10
11
17
4
16
15
Rating
19
Figure1
17
b. Select TV System using the UP/DOWN buttons, then press ENTER
to enter the submenu. Select the TV System you desire using the UP/
DOWN buttons, then press ENTER to confirm the setting.
Language
Video
Audio
TV Shape
Wide
TV System
NTSC
Rating
NTSC
PAL
Auto
TV System Display
3) Select AUDIO using the LEFT/RIGHT buttons, press ENTER to enter
the AUDIO setup page.
Language
Video
Digital out
Lpcm 48k DS
Audio
Rating
RAW
Off
Off
On
AUDIO Display Menu
a. Select Digital out using the UP/DOWN buttons, then press ENTER to
enter the submenu. Select the digital output you desire using the UP /
DOWN buttons, then press ENTER to confirm the setting.
Language
Video
Digital out
Lpcm 48k DS
AC3
Audio
E. Remote Control View (Refer to Figure 2)
Rating
RAW
PCM
Off
RAW
1) MODE Button
2) POWER Button
3) MENU Button
4) UP/DOWN/
LEFT/RIGHT Button
5) ENTER/PLAY Button
6) VOLUME +/- Buttons
7) NUMERIC KEYPAD
8) 10+ Button
9) TITLE Button
10) AUDIO Button
11) REPEAT Button
12) SUBTITLE Button
13) DISPLAY Button
14) EJECT Button
15) SETUP Button
16) PAUSE/Step Button
17) STOP/Memory Button
18) NEXT/Channel Up Button
19) PREVIOUS/Channel Down Button
20) SCAN FORWARD Button
21) SCAN REVERSE Button
22) MUTE Button
23) GOTO Button
24) ZOOM Button
25) A-B REPEAT Button
26) ANGLE Button
27) SLOW Button
Display Menu
16
5
Enter
/Add
/CH+
/CH-
Figure 2
F. Connections
White Audio In
2) Select Video by using the LEFT/RIGHT buttons, press ENTER
to enter the Video set up page.
Red Audio In
Yellow Video In
12DC
IN/OUT
Remote control
receiver
Language
Video
Audio
Rating
TV Shape
Wide
Normal/PS
TV System
NTSC
Normal/LB
Wide
S-video out
Digital Out
Video
TV ANTENNA
Yellow Video out
Red Audio out
(GND)Black
(ACC+)Red
Display
a. Select TV Shape using the UP / DOWN buttons, then press
ENTER to enter the submenu. Select the TV shape you desire
using the UP/DOWN buttons, then press ENTER to confirm the
setting.
White Audio out
Language
Figure 3
Video
Audio
Rating
TV Shape
Wide
Normal/PS
TV System
NTSC
Normal/LB
Wide
1. Powering your DVD Player ( Refer to Figure 3)
Connect the black wire (-) to the vehicle ground. Connect the red
wire (+) to a switched (Accessory) 12VDC source. Plug the other
end into the 12VDC input jack on the back of the unit.
2. Remote IR Receiver ( Refer to Figure 3)
Plug the 1/8 plug on the remote IR cable into the IR IN jack on
the back of the DVD player. Place the IR receiver anywhere in the
vehicle to allow remote control from any location.
3. Connecting to a Monitor
a. Match the color - coded plugs to the A/V OUTPUT jacks on the
back of the DVD Player A/V OUTPUT jacks: Yellow (video) to
Yellow, White (left audio) to White, and Red (right audio) to Red.
4. Connecting an External Video Source
To connect a video game or another audio/video source, plug the
A/V cable into either the A/V input jacks on the front or rear of the
DVD player.
6
TV Shape
Display
* Normal/PS: When the player is connected to a normal TV, and a
wide picture is shown on the full screen.
* Normal/LB: When the player is connected to a normal TV, and a
wide picture is shown on the screen with a black strip at both the
top and bottom of the screen.
* Wide: When the player is connected to a wide screen TV, a wide
picture is shown on the full screen.
15
b. Select Subtitle using the UP/DOWN buttons, then press ENTER
to enter the submenu. Select the Subtitle language you desire
using the UP/DOWN buttons, then press ENTER to confirm the
setting.
Language
Video
Audio
Rating
OSD Menu
English
English
Subtitle
English
Chinese
Audio
English
French
DVD Menu
English
Spanish
German
Dutch
Auto
Off
Subtitle Display
c. Select Audio using the UP/DOWN buttons, then press ENTER
to enter the submenu. Select the audio language you desire using
the UP/DOWN buttons, then press ENTER to confirm the setting.
Language
Video
Audio
NEXT
PREVIOUS
FAST REVERSE
English
English
English
Chinese
Audio
English
French
DVD Menu
English
Spanish
German
Dutch
Audio Display
d. Select DVD Menu using the UP/DOWN buttons, then press ENTER
to enter the submenu. Select the DISC Menu language you desire
using the UP/DOWN buttons, then press ENTER to confirm the
setting.
Audio
POWER
EJECT
PLAY
SLOW
PAUSE
STOP
FAST FORWARD
Subtitle
Video
1. BASIC OPERATION
Rating
OSD Menu
Language
G. Playing
After connecting power to the unit, press the power button on the main unit
momentarily. Insert the disc into the slot on the front of the unit, the unit will
load the disc and start playing automatically: If there is a disc inside the unit,
press the POWER button, the unit will start playing automatically.
Rating
OSD Menu
English
English
Subtitle
English
Chinese
Audio
English
French
DVD Menu
English
Spanish
German
UP/DOWN/LEFT/RIGHT
ENTER
NUMBERS
RETURN
MENU
REPEAT
DISPLAY
ANGLE
SUBTITLE
AUDIO
ZOOM
SETUP
Turn the unit on/off
Eject/load the disc
Start Play/Execute item or setting
Play at 1/2, 1/4, 1/6 or 1/7 times speed
Still Picture
(1 time) Stop at the present playing point /
(2 times) Stop playing
Go to the next chapter, track or scene during
play back
Go back to the preceding chapter, track or
scene during play back
Scan forward at 2, 4, 8 or 20 times normal
speed
Scan backward at 2, 4, 8 or 20 times normal
speed
Used for Menu Navigation
Execute item or setting
Select item or setting
Return
Display the root menu of the disc
Repeat playing title, chapter, or track
Display information (title, chapter, track, time,
etc.).
Change the angles of a scene
Select the subtitle language
Select the audio language
Enlarge an image to 2, 3, or 4 times the
original
For DVD playback Setup press stop and then
press Setup to select and set items, and exit
the setup menu.
Dutch
DVD Menu
14
Display
7
2. MENU
A DVD is divided into sections called titles and chapters. When you play
a DVD, a root menu of the disc will appear on the screen of your TV or
Monitor. Contents of the menu will vary depending on the disc content.
Press MENU during playback to display the main menu. Some DVDs
only allow you to select disc playback options using the DVD root menu.
12. SETUP
Press SETUP to display the Main screen of the SETUP Menu on
the screen. Press SETUP again to exit the SETUP Menu and the
unit will resume last playback mode.
Language
Video
Audio
Rating
3. DISPLAY
1) Display mode
During playback press DISPLAY once to display items 5, and 7. Press
DISPLAY twice to display the current disc playback information. Press
display again to remove the display.
1
10
11
12
2 3
4
5
6
7
DVD
00:00:35 00:03:53
Title 1/1
Chapter 1 / 8 Angle
1/1
Audio
1/2
6Ch ENG
Subtitle
1/2 CHI
Bitrate 8.448 Mbps
17
13 14
15
8
9
Main SETUP Menu Screen
1) Select language using the LEFT/RIGHT buttons, press ENTER to
enter the LANGUAGE setup page.
Language
Video
Audio
OSD Menu
English
Subtitle
English
Audio
English
DVD Menu
English
Rating
English
Ö Ð Î Ä
Francais
~
Espanol
Deutsch
16
Nederlands
Display Mode
1. The type of disc.
2. The number of current title.
3. The number of total titles.
4. The number of current chapter.
5. The elapsed time of title.
6. The number of total chapters.
7. The remaining time of title.
8. The number of the current angle.
9. The number of total angles.
10. The number of the current audio
language.
11. The number of total audio
languages.
12. The number of current subtitle
language.
13. The number of total subtitle
languages.
14. Current subtitle language.
15. Dolby audio mode.
16. Current audio language selected.
17. Current Bitrate
Language Display Menu
a. Select OSD Menu using the UP/DOWN buttons, then press
ENTER to enter the submenu. Select the OSD language you desire
using the UP/DOWN buttons, then press ENTER to confirm the
setting.
Language
Video
OSD Menu
English
Subtitle
English
Audio
English
DVD Menu
English
Rating
English
Ö Ð Î Ä
Francais
~
Espanol
Deutsch
Nederlands
OSD
8
Audio
Display Menu
13
USING THE REPEAT FEATURE
The default mode for the Repeat feature is OFF. Pressing REPEAT
consecutively changes the repeat options:
Repeat Single (repeat playback of a song)
Repeat All (repeat playback of the entire folder)
Off (normal playback)
Pressing REPEAT a 3rd time will resume normal playback. As you toggle
through the options, the repeat option changes. Selected repeat option
loops repeatedly until you turn it off.
NOTICE
Sign in front of a file name indicates that this is a folder, not
a Mp3 file.
Sign in front of a file name indicates that this is a MP3 file.
During MP3 playback, you cannot access ' PLAY MODE ', folders
or songs.
4) ANGLE
During playback press ANGLE to change the current angle of discs
containing multi-angles. (You can see item 8 in the display change) If
the disc has only one angle, you will see on the screen when pressing
ANGLE indicating that no other angles are available.
5) SUBTITLE
During disc playback press SUBTITLE* to select the desired subtitle
language. (You can see item 14 change)
6) AUDIO
During disc playback press AUDIO* to select the desired audio language.
(You can see item 10 in Picture 1 change) *NOTE: Some DVD's only
allow access to these functions through the DVD menu.
7) ZOOM
DVD
00:00:35 00:03:53
Title 1/1
Chapter 1 / 8
Audio
1/2
Subtitle
1/2 CHI
Bitrate 8.448 Mbps
Mp3
Angle
1/1
6Ch ENG
2
Zoom
11. Playing a JPEG file
in Display Mode
2
1) Insert the JPEG Disc into tray.
2) You can preview the JPEG file by pressing the MENU Button.
3) Press PLAY to playback the JPEGs in order.
4) Press PAUSE to STOP on a picture.
Zoom
Display
During playback press ' ZOOM ' to enlarge the picture by 1x, 2x or 3X
with the current zoom multiple displayed.
8) REPEAT
DVD
00:00:35 00:03:53
Title 1/1
Chapter 1 / 8 Angle
1/1
Audio
1/2
6Ch ENG
Subtitle
1/2 CHI
Bitrate 8.448 Mbps
Repeat Chapter
12
9
Repeat Chapter
Repeat Display
During playback press Repeat once to repeatedly play the current
chapter, press a 2nd time to repeat the current title, press a 3rd time and
the repeat function is cancelled and normal playback resumes. Repeat
mode sequence : Repeat Chapter/Repeat Title/Off.
As you toggle through the options, the repeat option changes. The selected
repeat option loops repeatedly until its turned off.
10. PLAYING MP3 DISCS
MP3 is a digital audio format. An audio CD-quality song is compressed
into the MP3 format with no significant loss of audio quality. CD-R /RW
discs that have been encoded in MP3 format are compatible with this
device.
Insert an MP3 Disc, the DVD player will initialize the disc and the
directory (folder) will be shown on the monitor screen.
CD-R
ROOT
9. PLAYING AUDIO CDS
When playing an audio CD the display will automatically display the disc
playback information. The options below show you what information is
displayed. Press the DISPLAY button to remove the display.
1. The current track.
2. The number of total tracks.
3. Playing time of the disc.
4. Remaining time of the disc.
--
Mode
MENU
--
Track 01
Track 02
Track 03
Track 04
Track 05
Track 06
Folder
MENU Screen
CD
Track 1 / 18
00:01:58
Normal
Display
01:12:54
1
3
2
4
Display in Playing CD
USING THE REPEAT FEATURE
The default mode for the Repeat feature is OFF. Pressing REPEAT
consecutively changes the repeat options:
Repeat Single- repeats the track that is playing.
Repeat All- repeats the disc that is playing.
Off
10
0
When an MP3 disc is inserted into the unit, the menu screen appears
automatically. You can use the menu screen to change folders and songs.
The system plays the songs in the order they were recorded onto the disc.
1. Press the
or
button to choose a folder from the folder list on
the left side of the screen.
2. Press ENTER to select the highlighted folder. All songs available
under the selected folder will be listed.
3. Use
or
button to choose a song from the list then press
ENTER to play the selected song.
Use the
( NEXT )button to move to the next song. Press the
(PREVIOUS) button to move to the beginning of the song.
11
Download PDF

advertising