Audiovox D2010 Portable DVD Player User Manual

Model D2010
PORTABLE DVD PLAYER
WITH 10.2" LCD MONITOR
Owner’s Manual
Introduction
Thank you for choosing the D2010 portable DVD Player. The unit applies
the latest state of the art electronics and is designed for use in hotels,
offices, vehicles or your home. The D2010 Player is constructed to
provide years of reliable, trouble-free service, and is compact so that you
can take it with you anywhere and is designed for quick and easy setup.
Please read all documentation prior to using this product. The
documentation will assist you in obtaining the best equipment
performance. Save this manual for later use.
Important Notice
It is unlawful in most jurisdictions for a person to drive a motor vehicle
which is equipped with a television viewer or screen that is located in the
motor vehicle at any point forward of the back of the driver’s seat, or that
is visible, directly or indirectly, to the driver while operating the vehicle.
In the interest of safety, this system should never be installed where it
will be visible, directly or indirectly, by the operator of the motor vehicle.
Safety Precaution
For safety reasons, when changing video media, it is recommended that
the vehicle is not in motion, and that you do not allow children to
unfasten seat-belts to change video media or make any adjustments to
the system.
Enjoy your entertainment system but always remember-safety of all
passengers remains the number one priority.
-1-
-2-
Cautions and Warnings
The lightning flash with arrowhead symbol, within an equilateral triangle,
is intended to alert the user to the presence of un-insulated “Dangerous
Voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
Important Safety Instructions
Power Supply:
Connect the (supplied) AC to DC adapter in the jack marked “DC 12V IN” on the right side of the
DVD player. Plug the two-prong end of the power cord to an AC110-220V outlet. If you have
difficulty inserting the plug, turn it over and reinsert it. If the unit will not be used for a long time,
disconnect the plug from the outlet.
Note:
Before plugging the power cord into an AC outlet, make sure that of all the other connections have
been made.
Caution:
To reduce the risk of electric shock, do not perform any servicing other than that contained in the
operating instructions. Service should only be performed by qualified service personnel.
Before Using the D2010:
1. Heed All Warnings.
2. Please Read And Follow All Instructions As Written In This Manual
3. Keep These Instructions.
4. Placement
To prevent fire or electric shock, do not expose this appliance to rain or moisture. Do not place the
set on an unstable cart, stand, tripod, bracket or table to prevent it from falling. Keep the DVD
Player away from strong magnets, heat sources, direct sunlight, and excessive dust. Do not use
the DVD Player in temperatures higher than 140 degrees Fahrenheit or 40 degrees Celsius. If the
DVD Player is brought directly from a cold location to a warm location, moisture may condense
inside the DVD Player.
-3-
Cautions and Warnings
When you move it from a cold location to a warm location, wait for about one hour before operating
the DVD Player, or remove the disc and leave the DVD Player turned ON until the moisture
evaporates.
5. Caution
Do not spill or spray liquid of any kind on or in the system (this may result in a fire or electric
shock). Do not place anything heavy on the DVD Player. To ensure proper ventilation and proper
operation, never cover or block the slots and openings with a cloth or other material. Keep the
DVD Player away from an open flame such as fire, candle etc. Only use attachments/accessories
specified by the manufacturer.
6. Warning
To reduce the risk of electric shock, do not perform any servicing other than that contained in the
operating instructions. There are no user-serviceable parts inside. Refer all servicing to qualified
service personnel. Replace the battery only with the same or equivalent type. In order to protect
the environment, please dispose of the battery properly. Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong. The wide blade or the third
prong is provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles, and the point where they exit from the
apparatus. Unplug this apparatus during lightning storms or when unused for long periods of time.
7. Cleaning DVD Player
When cleaning, make sure the system is unplugged from the power source. Do not use liquid
cleaners or aerosol cleaners. Use a soft cloth lightly dampened with water for cleaning the exterior
of the system only.
8. Disc
Do not use irregularly shaped discs such as heart or star-shaped discs as they may cause the
DVD Player to malfunction. Do not stick paper, tape or glue on the disc. Do not expose the disc to
direct sunlight or heat sources. Do not touch the surface of disc. Handle the disc by its edge. Clean
the disc by wiping the disc from the center out with a cleaning cloth. Remove the disc from the
DVD Player and store it in its case after playing. Software producers may intentionally fix some
playback operations of discs. Since this DVD Player plays discs according to the disc contents the
software producers designed, some playback features may not be available. Also refer to the
instructions supplied with the discs.
Copyright Protection
This product incorporates copyright protection technology that is protected by U.S.
patents and other intellectual property rights. Use of this copyright protection
technology must be authorized by Macrovision, and is intended for home and other
limited viewing uses only unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
-4-
Table Of Contents
Introduction---------------------------------------------------------------------------------------------- 1
Cautions and Warnings------------------------------------------------------------------------------ 2
Table of Contents--------------------------------------------------------------------------------------- 4
Main Features--------------------------------------------------------------------------------------------5
Screen and System Panel Controls-------------------------------------------------------------- 6
Front Panel Controls------------------------------------------------------------------------------------ 6
System Side Panel Controls------------------------------------------------------------------------ 7
Right Side Panel Controls------------------------------------------------------------------------------7
Left Side Panel Controls--------------------------------------------------------------------------------7
Remote Control----------------------------------------------------------------------------------------- 8
System Connections---------------------------------------------------------------------------------- 10
Power Supply Connection----------------------------------------------------------------------------- 10
Connecting to a TV-------------------------------------------------------------------------------------- 10
Connecting to an Amplifier---------------------------------------------------------------------------- 11
Connecting to a Digital Ready Amplifier------------------------------------------------------------ 11
System Preparations---------------------------------------------------------------------------------- 12
Using of Remote Control------------------------------------------------------------------------------- 12
Disc Formats Supported By This Player----------------------------------------------------------- 13
Power Supply-------------------------------------------------------------------------------------------- 14
Rechargeable Battery Pack--------------------------------------------------------------------------- 14
Attaching the Battery Pack---------------------------------------------------------------------------- 15
Charging the Battery Pack---------------------------------------------------------------------------- 15
Detaching the Battery Pack--------------------------------------------------------------------------- 16
Using the DC Adapter---------------------------------------------------------------------------------- 17
Installing The System Onto Vehicle Seat Back --------------------------------------------- 18
Installing The System Between Vehicle Seats ---------------------------------------------- 19
Using Headphones------------------------------------------------------------------------------------ 20
Using Wired Headphone------------------------------------------------------------------------------- 20
Using Wireless Headphone--------------------------------------------------------------------------- 20
DVD Player Operation-------------------------------------------------------------------------------- 21
System Setup------------------------------------------------------------------------------------------- 22
Playback Functions----------------------------------------------------------------------------------- 25
Troubleshooting--------------------------------------------------------------------------------------- 28
Specifications------------------------------------------------------------------------------------------ 29
-5-
Main Features
High Quality Audio and Video
Advanced Playing Function
LCD (Liquid Crystal Display) Screen
10.2” Color LCD screen.
Special Functions
Supports Multi-angle, Multi-language and
Parental-lock features.
AV Input
An external Audio/Video signal input
can be connected to the AV input
jacks.
Compatibility
Plays: DVD, DVD-R, CD, CD-R, CD-RW
and JPEG discs are compatible.
ON-Screen Display
ON-screen displays in your choice of
English /Spanish/French.
Search Function
Multi-speed, fast forward, fast reverse,
slow play and repeat playback.
Audio Output
Audio output jack for connection to an
external amp or powered speakers.
Zoom Function
Allows the viewer to enlarge in the
picture.
Video Output
Composite video output for connection to
an external monitor.
Search By Time
Search for a certain time on a disc.
Headphone Output
For listening to movies or music in
private.
Wireless IR Headphone Output
For use with optional wireless
infrared
headphones
Switching Power Adapter
Automatically
adapts
to
voltage
requirements in the U.S. and other
countries.
-6-
Last Memory Playback
Continues playback from a stopped point
as long as power is applied to the DVD
Player.
Region Code
DVD players and discs are coded by
region. These regional codes must
match. If the codes don’t match, the disc
cannot be played. This player’s code is
region 1.
Screen and System Panel Controls
Front Panel Controls
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
OPEN button
Press to open the disc tray cover.
Disc Tray Cover
When the disc is loaded gently
press the cover to close it.
PLAY button
Press to begin playback.
Remote Sensor
IR receiver for remote control
operation.
STOP button
Press to stop playback.
Power Indicator
Lights green when the player is on.
PAUSE button
Press once to pause playback.
Press again to activate step frame
by frame playback.
ENT button
Press to confirm selection.
Direction buttons
Press to select menu items or
settings.
MENU button
Press to display the disc root menu.
TITLE button
Press to display titles if present on
the DVD disc.
Next button
Press to skip to the next chapter or
track.
13. Forward Scan button
Press to scan forward.
14. Prev button
Press once to skip to the beginning
of the current chapter or track,
press twice to skip to the previous
chapter or track.
15. Reverse Scan button
Press to scan backwards.
16. Speakers
Provide high quality Audio output.
17. LCD Screen
10.2” TFT LCD Panel
18. Latch Hook
Used to lock the LCD panel to the
unit.
19. Infrared audio signal emitter
Used to transmit audio to optional
wireless headphones (IRHSCS)
20. -/+buttons
Use to adjust the brightness, color
and contrast level. Also used to turn
the infrared headphone emitter
power ON or OFF, and selecting the
LCD display ON or OFF.
When the LCD display is turned off,
press either of the PICTURE or +/buttons and the LCD display will turn
ON.
-7-
System Side Panel Controls
22. MODE button
Press to change the aspect ratio
from 4:3, 16:9 and zoom modes.
23. Charge Indicator
When charging the battery pack, the
light on the control panel will turn
red. When the battery is fully
charged the light will go OFF
21. PICTURE button
Press to enter the brightness, color
or contrast adjustment mode.
Infrared headphone emitter power
ON or OFF, and selecting the LCD
display ON or OFF.
Right Side Panel Controls
1. Volume Control
Used to adjust the headphone and
speaker volume.
2. Headphone Jack
Used to connect wired headphones
for
private
listening.
When
headphones are connected to this
jack the speaker output will turn off
automatically.
3. AV IN/OUT Switch
Switch to IN, to input an external
Audio/Video source. Switch to OUT
when the player is connected to an
external monitor.
4. Audio Input/Output Jack.
Used for connection to an external
amplifier or external audio source.
5. Video Input/Output Jack
Used for connection to an external
monitor or video source
6. 12V DC Input Jack
Used to connect the AC/DC
Adaptor or DC Vehicle Adaptor
Power to the unit.
Left Side Panel Controls
turn off.
2. Power ON/OFF Switch
Switch the power on or off.
1. Headphone jack
Used to connect wired headphones for private listening.
When headphones are connected
to this jack the speaker output will
-8-
Remote Control
Remote Control
5. ENTER button
Press to confirm the selected menu
items or settings.
1. PWR button
Press to turn the unit ON or OFF.
2. INFO button
Press to display detailed playback
information.
Keep pressing the button to display
additional information or to turn the
information display OFF.
6. SETUP button
Press to access the DVD player’s
setup menu.
7. Number buttons (0-9)
Press to select Password Numbers
or go to a specific Track or Time on
a disc. (GOTO Function)
3. TITLE button
Press to display titles if present on
the disc.
8. PREV button
Press to go to beginning of current
Track or Chapter. Press twice to go
to beginning of a previous Track or
Chapter.
4. Direction buttons
Press to select menu items.
-9-
Remote Control
9. NEXT button
Press to go to next Track or Chapter.
17. STOP button
Press once to stop playback. Press
the PLAY/PAUSE button to resume
normal playback. Press the button
10. SUBT button
When a DVD with subtitles is
twice to stop playback completely.
playing, press to select a subtitle
18. PLAY/PAUSE button
Press to start or pause playback.
language or to turn subtitles OFF.
11. Angle button
Press to access various camera
angles, if the DVD disc contains
multiple camera angles.
19. GOTO button
Press to select the desired disc
starting Time, Track or Title.
12. A-B Repeat button
Used to play a section of the DVD
from point “A” to point “B”.
Press
once to select the starting point (A)
press again to select the end point
20. +10 button
Select numbers greater than 9 by
pressing the (+10) button first, and
then additional number buttons as
needed.
(B). Press a third time to cancel the
21. FWD SCAN button
Press to search forwards at 2x, 4x,
A-B Repeat.
8x, 16x or 32x the normal
playback speed.
13. ZOOM button
Press to enter and cycle through
zoom functions, use the direction
buttons (4) to pan around the
screen.
22. REV SCAN button
Press to search backwards 2x, 4x,
14. REP button
Press to repeat a Track, Chapter,
Title, or the entire disc.
15. MENU button
Press to access the disc root menu.
8x,16x or 32x
playback speed.
the
normal
23. SLOW button
Press to activate slow forward. Slow
playback at 1/2, 1/4,1/8, 1/16 the
normal playback speed.
16. PIC button
Press to enter the brightness, color
or contrast level-adjusting mode.
Infrared headphone emitter power
ON/OFF or selecting the LCD
display ON/OFF.
- 10 -
24. AUDIO button
Press to access various audio
languages or tracks, when the DVD
disc contains multiple audio
languages or tracks
System Connections
Note: Before plugging the power cord into an AC outlet, make sure that all other
connections have been made as described below.
Power Supply Connection
Connect the supplied adapter to the side of the DVD player in the jack marked “DC
12V IN”. Plug the two-prong end of the power cord to an AC100-240V outlet. If you
have difficulty inserting the plug, turn it over and reinsert it. If the DVD Player will not
be used for a long time, disconnect the plug from the outlet.
Connecting to a TV
Audio/video connections
Always ensure that the DVD player, TV and any other electrical components are
switched OFF before connecting to the DVD player.
The easiest way to connect the DVD player to a television is via the supplied
Audio/Video cable. Connect the audio/video cable from the DVD player to the
audio/video inputs of the TV. And then switch the AV IN/OUT button to OUT.
Note: Noise may occur in speaker when there is an external audio signal input while
playing a DVD disc. Unplug the audio cord to clear the noise.
This player only outputs NTSC signals. Make sure to use NTSC input type monitor/TV.
If the picture is distorted or colorless, please check the type monitor/TV.
Do not connect an audio/video input while the A/V in/out switch is in the out position.
This may result in unwanted audio or video distortion.
- 11 -
System Connections
Connecting to an Amplifier
The DVD player can be connected to an amplifier. Plug the supplied A/V cable into the
audio jack on the right side of the unit and plug the other end into an audio input on
the amplifier (White= left, Red=Right). Please refer to the equipment’s manual before
connecting.
- 12 -
System Preparations
Using of Remote Control
1. Remove the battery holder. Refer to the figure above.
2.
Insert the battery into the battery holder (observe correct polarity) and insert the
battery holder into the remote.
3.
For best results, aim the remote directly at the player’s IR receiver window, within
15 feet, and angles not exceeding 60 degrees.
The path between the remote control and remote sensor should be free of
obstructions.
4.
Under normal use the battery will last for approximately one year.
5.
Remove the battery if the remote is not to be used for a long time.
6.
Battery type is a CR2025
- 13 -
System Preparations
Disc Formats Supported By This Player
DISC LOGO
DIAMETER
PLAYBACK TIME/
PLAYABLE SIDES
133 min (SS-SL)
12cm
DVD
DVD-R
242 min (SS-DL)
266 min (DS-SL)
484 min (DS-DL)
41 min (SS-SL)
8cm
75 min (SS-DL)
82 min (DS-SL)
150 min (DS-DL)
CD
CD-R
CD-RW
12cm
74 min
8cm
20 min
The disc maker specifies the operation of some DVD discs.
instruction manual with the disc.
Please refer to the
Care of Discs
Cleaning of Discs
Do not touch the playing surface of the
disc.
Do not stick paper or labels on the disc.
If a disc has fingerprints or dust on it,
lightly wipe the disc with soft cloth from
the center of the disc outward.
Storage of Discs
Never use record cleaning sprays, or
any other solvents to clean your discs.
Do not expose discs to direct sunlight or
excessive temperatures.
- 14 -
Power Supply
Rechargeable Battery Pack
Your portable DVD player comes with a lithium ion rechargeable battery that attaches
to the rear of the DVD player. Charge the battery fully before initial use. Charging time
is normally about 5 hours. A fully charged battery delivers about 2-1/2 to 3 hours of
use, but playing time varies from disc to disc. If the battery will not be used for a long
period of time, fully charge the battery prior to storage.
Working conditions and precautions of the battery
• New batteries must be fully charged before initial use. Regardless of the charge
indicator, allow the battery to charge for 8 hours.
•
Battery should only be used and charged when temperatures are between 32 100F.
•
Never put the battery in fire or water.
•
Do not expose the battery to high temperatures or store in hot, sunny places.
•
Maintain well-ventilated conditions around the product to avoid overheating. Don’t
•
Do not short the battery terminals.
•
Do not open the battery.
put the product on bed, sofa or anything that may block ventilation to the product.
•
Detach the battery after charging is complete. When charging the battery pack,
the charge light will turn red, when the charging is complete, the light will turn
OFF.
•
Detach the battery when not in use.
•
When the battery is weak, “Low Power” will appear on the LCD screen and about
one minute later, the player will power OFF automatically.
- 15 -
Power Supply
Attaching the Battery Pack
Refer to the following steps for attaching the Battery Pack:
1.
Place the DVD Player on a soft and smooth surface with the bottom of the unit
facing UP (chassis up see the Fig.1).
2. With one hand on the DVD Player to prevent it from moving, take the battery and
align the four (4) plastic tabs on the battery pack with holes on the player, and
push the battery pack into the DVD Player. (see the Fig.1).
3.
Slide the Battery Pack until you hear it click and lock into place (see the Fig.2).
Fig.1
Fig.2
Charging the Battery Pack
The battery pack must be attached to the DVD player to charge it using the supplied
AC Power Adapter.
1.
2.
Attach the battery pack to the DVD player
Plug the supplied AC Power Adapter into the player’s power jack marked
with ”DC+12V IN”, which is located on right side of the DVD Player.
3.
Plug the other end of the AC Power Adapter Cord into a household AC Outlet as
shown below.
- 16 -
Power Supply
Detaching the Battery Pack
If the DVD Player is not going to be used for long periods of time, the battery pack
should first be fully charged and the Battery Pack should be detached. When the
DVD Player is turned OFF, the DVD Player is still consuming some power in
STANDBY mode. This will eventually discharge the battery.
Make sure the power is turned OFF before detaching the Battery Pack.
1.
Place the player on a soft and smooth surface with the bottom of the unit facing
2.
Press and hold the Battery Release Tab (1) (located on the bottom) in the
up.
direction of the arrow as shown below.
3.
Remove the Battery Pack by gently sliding it towards the side of the unit (2).
4.
Carefully remove the Battery Pack from your player.
- 17 -
Power Supply
Using the DC Adapter
To use the supplied Vehicle DC Adapter, disconnect the Battery pack and connect the
Vehicle Power Plug Adapter into the DVD Player’s Power Jack and the other end into
the Vehicle DC outlet (Cigarette Lighter Socket) as shown below.
Vehicle
Power
Plug
Quick Tips:
•
Do not operate the unit while driving a vehicle.
•
Place the unit in a secure position for viewing.
•
Do not leave battery attached when using car adaptor as power source.
•
Do not connect the unit to the car adapter when starting the car.
Pre-Operation
1.
Connect DVD Player to power source.
2.
Unlock and lift the LCD screen up.
3.
Switch the “POWER” to the “ON” position.
4.
Press the “OPEN” button to open the disc cover.
5.
Put the disc into the tray with the printed side facing up.
6.
Close the disc cover.
7.
Adjust the volume with the “VOLUME” control (also adjusts headphone volume if
using headphones).
- 18 -
Installing The System Onto Vehicle Seat Back
1.
2.
3.
Take one of the supplied straps from the carrier bag. Connect the latch to one
of the upper metal rings on the mounting bag. Connect the “S” hook to the
other upper metal ring and place the loop over the headrest. Adjust the strap
until the bag is firmly secured.
Take another strap from the carrier bag, and connect the latch to the lower
metal ring on the left side of the bag. Attach the “S” hook to the same ring after
looping the strap around the seat rail. Repeat this process for the right side. In
some vehicles, it may be necessary to attach the “S” connector to the rail
directly, as it may not be long enough to reach back to the ring.
Adjust the straps tightly so that the bag is secured.
- 19 -
Installing The System Between Vehicle Seats
1.
2.
3.
Take one strap and connect the latch to the upper metal ring on the left side of
the bag. Attach the “S” hook to the same ring after looping the strap around
the headrest of the driver’s seat. Repeat this process for the right side
(Passenger Seat).
Take another strap and connect the latch to lower metal ring on the left side of
the bag. Attach the “S” hook to the same ring after looping the strap around
the driver’s seat rail. Repeat this process for the right side. In some vehicles, it
may be necessary to attach the “S” connector directly to the rail, as it may not
be long enough to reach back to the ring.
Adjust the straps tightly so that the bag is secured.
- 20 -
Using Headphones
Using Wired Headphone
Connect headphones into the headphone Jack on the left or right side of the unit.
Quick Tips:
Excessively loud volume could damage your hearing.
Turn down the volume before you connect the headphones, and then raise the volume
to a comfortable level.
Sound from the DVD Player’s external speaker will stop when headphones are
connected.
Using Wireless Headphone (Optional)
1. For best results when using wireless headphones sit facing the screen within the
range of 8 feet and not more than 30 degrees left and right of center. There should
be no obstacles between the wireless headphones and the infrared audio signal
emitter.
2. Press the PIC button on the front panel until “Infrared Headphone Emitter” power
ON/OFF is displayed.
3.
In the Infrared Headphone Emitter power ON/OFF select mode, press the +/button on the front panel to select ON.
4. If there is no sound, make sure that the headphones are on and that the volume is
turned up and that the batteries in the headphones are not discharged.
- 21 -
DVD Player Operation
Preparation
1.
Turn on the player’s power by switching the POWER switch on the side of the
player to “ON”.
2.
Unlatch the LCD panel and lift it up.
3.
Press the OPEN button on front panel to open the disc cover.
4.
Load disc with the label facing up.
5.
Close the disc tray cover, pressing the area of the disc cover that says “Press”.
The player will automatically search for the disc and start playback.
Playback of DVD Disc
When the DVD menu appears press the direction buttons () to select an
option. Press the ENTER or PLAY to start the selected option.
Pause
Press the Play/Pause button once on the remote control to pause playback.
Press the Play/Pause button again to resume normal playback.
Zoom
Press the ZOOM button on the remote control to cycle through the different zoom
settings. While in the zoom mode use the direction buttons to move around to different
positions on the screen.
Stop
During playback, press the STOP button once on the remote control to stop playback
of a disc. Press the PLAY/PAUSE button and the DVD Player will resume playback of
the disc from the point where it was stopped.
Screen Mode
Press the MODE button on the front panel to switch the screen aspect ratio between
16:9, 4:3 and ZOOM.
Previous and Next
Press the PREV button once to return to the currently playing Chapter or Track.
Press the PREV button twice and playback will start from the previous Chapter or
Track.
Press the NEXT button on the remote control and playback of the disc will start
from the next Chapter or Track.
- 22 -
System Setup
You can customize the set up menu to your own preference.
Press the “SETUP” button on the remote control to display the setup menu. The menu
will include “General Setup”, “Speaker Setup”, “Dolby Digital Setup”, “Video Setup”,
and “Preference Setup”. Press the direction button () on the remote control
to select a category. All the items in the category will appear on the screen. Press
the “ENTER” button to enter the category.
Category
When you enter a category all the items under this category will appear, the
highlighted category is the current set up.
Press the right direction button () on the remote control to select another category
(new selection will be highlighted). Press the “ENTER” button for confirmation.
Press the left direction button () to enter the other setup menu(s).
General Setup
TV Display
Select Normal/PS or Normal/LB when a 4:3 TV is connected.
Select Wide when a 16:9 when using the screen on the unit or when a wide screen TV
is connected to the video output.
Angle Mark
If the scene was shot from multiple angles, you can change the camera angle of the
scene you are watching. Not all DVD’s have this feature.
ON/OFF
With this switched on an angle icon will appear on the screen you will be notified if
alternative viewing angles are available.
OSD Lang
There are three different OSD languages for selection. You can select from English,
Spanish or French.
SPDIF Output
Not used in this model.
- 23 -
System Setup
Captions
You can choose captions ON or OFF during playback.
Screen Saver
When activated, the unit will go into screensaver mode if the same image remains on
the screen for 3 minutes.
Last Memory
Select on, and the unit will resume playback from the point where playback was
stopped.
Speaker Setup
Downmix
Select “LT/RT” in DOWNMIX, the player will output the audio signal IN MIXED MONO.
Select “Stereo”, then the player will output a stereo signal.
Dolby Digital Setup
Dual Mono
The function is used to select from stereo, left only, right only, and mixed mono.
Dynamic
Use this item to adjust linear dynamic compression rate to get different signal
compression effects.
Video Setup
Sharpness
Use this setting to adjust the sharpness level to one of three settings: High, Medium or
Low.
Brightness
Use this setting to adjust the brightness level.
Contrast
Use this setting to adjust the contrast level.
- 24 -
System Setup
Preference Page
Audio, Subtitle, Disc Menu
This setting allows you to hear or read the subtitles of a DVD in your choice of English,
Spanish and French etc. if the disc contains multiple languages.
Parental
DVD discs equipped with the child lock function are rated according to their contents
and settings vary from disc to disc. Depending on the disc, you can lock out playback
of the disc altogether. Access parental control by pressing the (direction buttons)
on the remote control, then press the ENTER button.
Password
Parental control features are password protected. The original setting is unlocked.
This setting allows you to use number buttons to input any password.
Note: The Default Password is 3308. This password is always effective even after you
have selected your own password and changed it. To avoid the possibility of others
using the default password to set the parental level and change the password, you
can record this default password in another area and delete it from this manual. Some
discs can be limited depending on the age of users while some discs cannot.
Default Reset
Use this function to reset all the settings.
Note: For preference setting the unit must be in the stop mode.
Audio
DVD discs can contain up to 8 audio bit streams. For Example: English, Spanish,
French etc.
To select the audio bit stream you prefer press the AUDIO button on the remote
control during playback. The DVD player will play the next audio bit stream every time
you press the AUDIO button in succession.
Note: This function is only available for discs that have several audio bit streams
recorded onto it.
- 25 -
Playback Functions
Forward and Reverse Scan
Press the and buttons to Forward or Reverse scan a disc during playback (x2,
x4, x8, x16 x32).
Slow Forward
Press the SLOW button to Slow Scan a track on a disc during playback (1/2, 1/4,1/8,
1/16).
Repeat
Repeat a Title, Chapter or Track. Press the REP button on the remote control.
Continually pressing the REP button will display a menu as follows: Repeat Chapter,
Title, All.
You can temporarily select a section of a DVD that you would like to play repeatedly.
You do this by marking the start and the end of the section using the A/B button.
During playback press the A-B button on the remote control at the beginning of the
segment (point A) you wish to play repeatedly. Press the A-B button again to mark the
end of the segment (point B).
The DVD player will automatically return to point A and repeat playback of the
selected segment (A-B). To resume normal playback, press the A-B button again.
Subtitle
A DVD disc can be recorded with up to 32 subtitles.
Press the SUBT button on the remote control during playback to select the one you
prefer.
NOTE: This function is only available on DVD discs that are recorded with
multi-subtitles.
Angle
If the scene was recorded from multiple angles, you can change the camera angle of
the scene you are watching.
Press the ANGLE button on the remote control during playback. Playback will shift to
another angle. If the disc menu gives the options of angles items, you can switch
angles for viewing by pressing the number buttons on the remote control.
Note: This function is only available if a disc has multiple angles recorded on the disc.
- 26 -
Playback Functions
Search by time
During DVD disc playback, press the GOTO button on the remote control once, there
will be a menu displayed on the screen. Use the direction buttons to select the
desired item and press the Enter button. Select Title or Chapter and use the number
buttons to input the desired title or chapter number. Press the direction button to
return.
Note: some DVD discs may not support this function.
Resume Playback
Press the STOP button at the point if you wish to stop the playback of a disc. The
DVD Player will memorize the location where playback of the disc was stopped.
Press the Play/Pause button to resume normal playback. The DVD Player will resume
the playback of the disc from the location where it was stopped. This function will not
operate if the disc is removed from the DVD Player.
Press the STOP button twice (2). Playback of the disc will stop. When the Play/Pause
button is pressed again, playback of the disc will start from the beginning of disc.
- 27 -
Playback Functions
Playing a JPEG
JPEG is a common picture format. Hundreds of pictures can be stored in a disc in this
format and viewed on the LCD screen.
Normal Playback
Load a JPEG disc into the DVD Player. After reading the disc, the DVD Player will
display the JPEG file on the left side of the screen and the preview picture on the right
side of the screen.
Use the direction buttons to select the picture you wish to view and then press
the ENTER button to confirm and start playback. During playback of the disc, use the
and buttons to select the next picture or previous picture. Press the MENU
button to enter the preview menu.
Picture Rotation
The picture can be rotated by using the cursor buttons.
Picture Zoom
The ZOOM button is used to enlarge the picture by 2x, 3x or 4x the normal size or
reduce the picture by 1/2,1/3,or 1/4 normal size. First press the ZOOM button to enter
the zoom mode, then use the fast forward or reverse scan button to enlarge or reduce
the picture.
With the zoom function turned ON, use the direction buttons to move to a desired
position of the picture.
When the ZOOM function is turned off, the picture will display normally.
•
Some JPEG discs can be played normally but with no rotate or zoom functions
depending on how the disc was produced.
- 28 -
Troubleshooting
Symptom
How To Check
The player cannot play.
• Make sure the AV IN/OUT switch on the right side of
the player unit is in the OUT position for standard
play.
• Make sure the disc door is completely closed.
• Make sure a disc is loaded.
• Make sure the disc is loaded with label side up.
• Disc should be clean, not dirty or warped.
• Player’s region code should be the same as the
region code of the DVD disc.
• Make sure water condensation has not occurred? If
it has, remove the disc and keep the player power
on until the moisture evaporates.
There is no sound.
•
•
•
•
Make sure the system connection is correct.
Make sure the sound setup of DVD disc is correct.
Is your disc dirty or warped? Clean or replace it.
If wired headphones are plugged in, unplug them.
•
Poor AV performance.
Make sure TV is turned on and in correct video
mode.
• Make sure your system connection is correct.
• Is your disc dirty or warped? Clean or replace it.
Cannot continue to play and
play a section repeatedly.
• Make sure the player is not in A-B repeat mode.
• Press A-B button to cancel A-B repeat status.
• Is your disc dirty or warped? Clean or replace it.
The remote control does not
work.
• Make sure there is no obstruction between the
remote control and the player.
• Make sure you are pointing the remote control
towards the player.
• Make sure battery is inserted correctly (check
polarity).
• Replace weak battery.
There is no picture.
WARNING: Do not touch any metal objects to the Battery connectors, as it will put
the Battery in standby mode. To exit the standby mode, connect the Battery and
DVD Player to AC or DC power.
Other possibilities:
Static or other external interference may cause the player to function abnormally.
Unplug the power-supply cord from the outlet and plug it in again to reset the player so
that normal operation can resume. If you are still having problems, then disconnect the
power to the DVD Player and consult a qualified technician.
- 29 -
Specifications
Screen resolution
800 x 480
TFT screen size
10.2 inches (259.08mm) (16:9)
Laser Wavelength
Wavelength: 780/650nm
Video System
NTSC
Frequency Response
20Hz - 20kHz ±2.5dB
Audio Signal-to-Noise
≥ 85 dB
Audio distortion + noise
≤ -70dB (1KHz)
Channel Separation
≥ 70dB (1KHz)
Dynamic Range
≥ 80dB (1KHz)
0.2
Audio Out
Analog Audio Out
Video Out
Video Out
Power
AC100-240V 50/60Hz
Power Consumption
Dimension w (o) battery
Weight w/o battery
Output Level: 1.5V±1.0 , Load: 10KΩ
Output Level:1VP-P±0.2,
Load: 75Ω
Unbalanced Negative
25W
10.51in (267mm)×8.38in (213mm) 7.16in (182 mm)×1.22in (31mm)
About 3.30/2.71lbs (1.5/1.23 kgs)
DESIGN AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Confidential unpublished works. © 1992 -1997 Dolby Laboratories.
All rights reserved.
- 30 -
WARRANTY
90 DAY LIMITED WARRANTY
Applies to Audiovox Video Products
AUDIOVOX ELECTRONICS CORP. (the Company) warrants to the original retail purchaser of this product that should this product or any part
thereof, under normal use and conditions, be proven defective in material or workmanship within ninety (90) days from the date of original
purchase, such defect(s) will be repaired or replaced with reconditioned product (at the Company's option) without charge for parts and
repair labor. A game controller, if supplied, is similarly waranteed for ninety (90) days.
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated
bill of sale), specification of defect(s), transportation prepaid, to the Company at the address shown below.
This Warranty does not extend to the elimination of externally generated static or noise, to correction of antenna problems, to costs
incurred for installation, removal or reinstallation of the product, or to damage to digital memory cards, discs, speakers, accessories, or
electrical systems.
This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through
alteration, improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code
label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT
PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY
PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities.
ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED
WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR
BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT
WITHIN A PERIOD OF 24 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR
ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED,
WHATSOEVER. No person or representative is authorized to assume for the Company any liability other than expressed herein in
connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential
damage so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have
other rights which vary from state to state.
AUDIOVOX ELECTRONICS CORPORATION, 150 MARCUS BLVD. HAUPPAUGE, NEW YORK. 11788 1-800-645-4994
CANADA : CALL 1-800-645-4994 FOR LOCATION OF WARRANTY STATION SERVING YOUR AREA
© 2005 Audiovox Electronics Corporation
128-5556E
- 31 -
For Customer Service
Visit Our Website At
WWW.audiovox.com
Product Information, Photos,
FAQ’s Owner’s Manuals
© 2005 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788
- 32 -
128-7128A