Specifications | Audiovox FP2000 Flat Panel Television User Manual

WARNING
To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or
moisture.
To reduce the risk of fire, do not cover the
ventilation opening of the apparatus with
newspapers, tablecloths, curtains, etc.
Do not place the naked flame sources such
as lighted candles on the apparatus.
To reduce the risk of fire or electric shock,
do not expose this apparatus to dripping
or splashing, and do not place objects
filled with liquids, such as vases, on the
apparatus.
As the main plug is used to disconnect
the unit from the mains, connect the unit
to an easily accessible AC outlet. Should
you notice an abnormality in the unit,
disconnect the main plug from the AC
outlet immediately.
Do not install the appliance in a confined
space, such as a bookcase or built-in
cabinet.
Do not expose batteries or apparatus with
battery-installed to excessive heat such as
sunshine, fire or the like.
The unit is not disconnected from the
mains as long as it is connected to the
AC outlet, even if the unit itself has been
turned off.
GB
CAUTION
The use of optical instruments with this
product will increase eye hazard.
This appliance is classified as a CLASS 1
LASER product. This marking is located
on the rear exterior.
Notice for the customers in the
U.S.A. and Canada
This symbol is intended
to alert the user to the
presence of uninsulated
“dangerous voltage”
within the product’s
enclosure that may be
of sufficient magnitude
to constitute a risk
of electric shock to
persons.
This symbol is intended
to alert the user to the
presence of important
operating and
maintenance (servicing)
instructions in the
literature accompanying
the appliance.
Owner’s Record
The model and serial numbers are located
on the rear of the unit. Record these
numbers in the space provided below.
Refer to them whenever you call upon
your Sony dealer regarding this product.
Model No.
Serial No.
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
8) Do not install near any heat sources
such as radiators, heat registers,
stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of
the polarized or grounding-type plug.
A polarized plug has two blades with
one wider than the other. A grounding
type plug has two blades and a third
grounding prong. The wide blade or
the third prong are provided for your
safety. If the provided plug does not fit
into your outlet, consult an electrician
for replacement of the obsolete outlet.
10)Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and
the point where they exit from the
apparatus.
11)Only use attachments/accessories
specified by the manufacturer.
12)Use only with the cart,
stand, tripod, bracket,
or table specified by
the manufacturer,
or sold with the
apparatus. When
a cart is used, use
caution when moving
the cart/apparatus
combination to avoid
injury from tip-over.
13)Unplug this apparatus during lightning
storms or when unused for long
periods of time.
14)Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus,
the apparatus has been exposed to
rain or moisture, does not operate
normally, or has been dropped.
GB
The following FCC statement applies
only to the version of this model
manufactured for sale in the U.S.A.
Other versions may not comply with
FCC technical regulations.
NOTE:
This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses and can radiate radio frequency
energy and, if not installed and used
in accordance with the instructions,
may cause harmful interference to
radio communications. However, there
is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television
reception, which can be determined
by turning the equipment off and on,
the user is encouraged to try to correct
the interference by one or more of the
following measures:
 Reorient or relocate the receiving
antenna.
 Increase the separation between the
equipment and receiver.
 Connect the equipment into an
outlet on a circuit different from that
to which the receiver is connected.
 Consult the dealer or an experienced
radio/TV technician for help.
CAUTION
You are cautioned that any changes or
modifications not expressly approved in
this manual could void your authority to
operate this equipment.
GB
About product
registration (for U.S.
customers only)
Proper registration will enable us to
send you periodic mailings about
new products and other important
announcements. Registering your
product will also allow us to contact you
in the unlikely event that it will need
adjustment or modification. Please take
the time to register your new product at
our website:
http://www.sony.com/productregistration
You will find the product serial number
on the main unit and the carton box.
If you have any operational questions
regarding your new purchase, please
contact your retailer. For the location
of a Sony dealer in your area, or for any
other questions, please call 1-800-222SONY(7669).
About this manual
The instructions in this manual are for
models MHC-GZR333i and LBTLCD77Di. Each model consists of the
following components.
MHC-GZR333i
Main unit:
HCD-GZR333I
Speaker system:
SS-GZR777D (Front speakers)
LBT-LCD77Di
Main unit:
HCD-LCD77DI
Speaker system:
SS-LCD77DI (Front speakers)
In this manual, the MHC-GZR333i is
used for illustration purposes unless
stated otherwise.
Icons, such as
, listed at the top
of each explanation indicate what kind
of media can be used with the function
being explained.
The Control Menu items may be
different depending on the disc.
The Control Menu items may vary
depending on the area.
The Setup Menu items may be different
depending on the area.
The order of the displayed items may
be different from the actual display.
DivX and MPEG4 video files can only
be played back on MHC-GZR333i.
You can view any video files (including
MPEG4 video files) stored in your
iPod.
GB
Table of Contents
About product registration
(for U.S. customers only)..................... 5
About this manual................................ 5
Playable discs......................................... 8
Guide to parts and controls............11
Getting Started
Hooking up the system
securely...................................................23
Hooking up the TV.............................27
Setting the LCD....................................31
Setting the clock.................................32
Performing “QUICK” setup...............33
Using the “THEATRE SYNC”
function..................................................35
Disc
Playing a disc........................................36
Using play mode.................................50
Adjusting the delay between the
picture and sound (“A/V SYNC”)....55
Restricting playback of the disc
(PARENTAL CONTROL).......................56
Using the Setup Menu......................58
GB
Tuner
Listening to the radio........................64
iPod
Playing the iPod...................................66
USB Device
Before using the USB device with
this system.............................................72
Transferring music from a disc
to a USB device....................................73
Recording analog audio
to a USB device....................................78
Playing a file of the USB device......79
Sound Adjustment
Adjusting the sound..........................87
Singing along: Karaoke.....................90
Other Operations
Using the timers..................................95
Changing the display........................97
Hooking up optional
components....................................... 100
Additional Information
Troubleshooting............................... 103
Precautions......................................... 120
Specifications.................................... 123
Compatible devices with this
system.................................................. 126
Compatible iPod models with this
system.................................................. 128
Guide to the Control Menu
display.................................................. 129
Playback priority of file types...... 133
Language code list.......................... 134
Glossary............................................... 136
Index..................................................... 140
License and Trademark Notice.... 142
GB
Playable discs
Type
Disc logo
DVD VIDEO
GB
Characteristics
 DVD VIDEO
 DVD-R/DVD-RW in DVD
VIDEO format or video mode
 DVD+R/DVD+RW in DVD
VIDEO format
VR (Video
Recording)
mode
 DVD-R/DVD-RW in VR (Video
Recording) mode (except for
DVD-R DL)
VIDEO CD
 VIDEO CD (Ver. 1.1 and 2.0
discs)
 Super VCD
 CD-R/CD-RW/CD-ROM in
video CD format or Super VCD
format
CD
 Audio CD
 CD-R/CD-RW in audio CD
format
Icon
Type
DATA CD
DATA DVD
Disc logo
Characteristics
Icon
 CD-R/CD-RW/CD-ROM in
DATA CD format, containing
MP3 files, JPEG image files,
DivX video files and MPEG4
video files, and conforming to
ISO 9660 Level 1/Level 2, or
Joliet (extended format)
 DVD-ROM/DVD-R/DVD-RW/
DVD+R/DVD+RW in DATA
DVD format, containing MP3
files, JPEG image files, DivX
video files and MPEG4 video
files, and conforming to UDF
(Universal Disk Format)
MP3 files: MP3 (MPEG 1 Audio Layer 3) is a standard format defined by ISO (International
Organization for Standardization)/MPEG (Moving Picture Experts Group) which compresses
audio data. MP3 files must be in MPEG 1 Audio Layer 3 format.
JPEG image files: JPEG image files must conform to the DCF image file format (DCF “Design rule
for Camera File System”: Image standards for digital cameras regulated by “Japan Electronics and
Information Technology Industries Association” (JEITA)).
DivX video files: DivX video files must be recorded in DivX format with the extension “.avi” or
“.divx”. DivX video files can only be played back on MHC-GZR333i.
MPEG4 video files: MPEG4 video files must be recorded in MP4 file format with the extension
“.mp4” or “.m4v”. MPEG4 video files can only be played back on MHC-GZR333i.
ISO 9660: A logical format of files and folders on CD-ROMs, defined by ISO.
Continued

GB
Discs that cannot be played
CD-ROMs recorded in PHOTO CD
format
DATA CDs recorded in MP3 PRO
format
Data part of CD-Extras1)
Data part of Mixed CDs2)
Super Audio CDs
DVD Audio discs
DVD-RAMs
CPRM compatible DVD-R/RW
recorded in Copy-once programs3)
Discs of non-standard shape (for
example, heart, square, star)
Discs that have adhesive tape, paper, or
sticker attached to them
Rental or used discs with attached seals
where the glue extends beyond the seal
Discs that have labels printed using ink
that feels tacky when touched
CD-Extra: This format records audio
(AUDIO CD data) on the tracks in session 1
and data on the tracks in session 2.
2)
Mixed CD: This format records data on the
first track and audio (AUDIO CD data)
on the second and subsequent tracks of a
session.
3)
CPRM: “Content Protection for Recordable
Media” is a coding technology that protects
copyright for Copy-Once programs.
1)
See “Region code of DVD VIDEOs you
can play back on this system” and “Notes
on discs” (page 120) regarding the region
code and notes on discs.
10GB
This manual mainly explains operations using the remote, but the same operations can
also be performed using the buttons on the unit having the same or similar names.
Main unit
Continued

Guide to parts and controls
Guide to parts and controls
11GB


 (on/standby) button
DVD/TUNER MENU button
(page 45, 65, 80)
Press to turn on or off the system.
Lights up when the system is turned off.
Press to turn on or off the menu items on
the TV screen.
Press to preset the radio station.


Display
ENTER button
STANDBY indicator

DISPLAY button (page 32, 97)
Press to display the disc information or
clock in the front panel display.

OPTIONS button (page 31, 98)
Press to enter the option menus.

DVD TOP MENU button (page 37)
Press to display the DVD title on the TV
screen.
12GB
Press to enter the settings.

RETURN button (page 46, 82)
Press to return to the previous menu on
the TV screen.

DISPLAY button (page 34, 129)
Press to turn on or off the Control Menu
on the TV screen.
The Control Menu is displayed only
when the “DVD” function or “USB”
function is selected.

CLEAR button (page 46, 51, 76,
84)
TIMER indicator
Press to delete a pre-programmed track.
Press to erase files or folders from the
connected optional USB device.
Press to return to the original display
when viewing the rotated image.
Press to switch the TV’s input source
to “COMPONENT 3” while using
“THEATRE SYNC.”

LCD DISPLAY ON/OFF button
Lights up when the Play Timer or Rec
Timer is set, and flashes when the Sleep
Timer is set.

Dolby D (Dolby Digital) indicator
DTS indicator
Indicates the current surround format.

USB MEMORY indicator
Press to turn on or off the front panel
display.
Lights up when the USB device is
recognized.


/// button
Press to select the menu items.

iPod Dock (page 26)
Place an iPod into the iPod Dock to enjoy
audio and video contents stored in the
iPod.
Guide to parts and controls

DISC 1  DISC 3* button
(page 38, 74)
Press to select a disc.
Press to switch to the “DVD” function
from other function.
Lights up when a disc is in the disc tray,
and flashes when the disc tray is selected.
OPEN/CLOSE  button

Press to load or eject a disc.
Remote sensor
DISC SKIP/EX-CHANGE button
(page 36, 38, 74)
Press to select a disc.
Press to exchange a disc while playing.
Continued

13GB


* (play) button
REC TO USB button (page 74, 78)
Press to start playback.
Press to transfer music from a disc or
record the sound from an analog audio
source to the connected USB device.
Press to mark track numbers during
recording.
* (pause) button
Press to pause playback.
 (stop) button
Press to stop playback.
/ (rewind/fast forward)
button
Press to find a point in a track, file,
chapter or video file.
/
button

OPERATION DIAL (page 37, 65)
Turn to select a track, chapter or video
file.
Turn to select the preset station.

MASTER VOLUME
Press to watch the slow‑motion play.
Turn to adjust the volume.
TUNING +/ button

Press to tune in the desired station.
MIC LEVEL
Turn to adjust the microphone volume.
ECHO LEVEL
Turn to adjust the echo level.

Disc tray
14GB


Connect an optional USB device.
(USB) indicator
SOUND FIELD button (page 89)
Press to select the sound field for the
surround sound.
Lights up in blue when the system is
turned on.
Lights up in red when transferring or
recording to the connected optional USB
device or when erasing audio files or
folders.


Press to select the “VIDEO” or “SAT”
function.
EQ BAND/MEMORY button
(page 88)
Press to select the frequency band when
adjusting the equalizer.
GROOVE button (page 87)
Press to reinforce the bass.

VIDEO/SAT* button (page 102)

TUNER/BAND* button

Press to select the “TUNER” function.
Press to switch among FM and AM band.
MIC jack

Connect a microphone.

PHONES jack
Connect the headphones.
Guide to parts and controls
(USB) port
iPod/OPR* button (page 67, 68)
Press to select the “iPod” function.
Press to switch the operating mode to
iPod Display mode or Main Display
mode.

PRESET EQ button (page 87)
Press to select the preset sound effect.
Continued

15GB

USB* button
Remote
Press to select the “USB” function.

DVD* button
Press to select the “DVD” function.
* Lights up when selected.

 (on/standby) button
Press to turn on or off the system.
TV 1) (on/standby) button
Press to turn on or off the TV.
16GB

DISC SKIP button (page 38, 74)
SUBTITLE button (page 38)
Press to select a disc.
Press to switch the language of the
subtitle (DVD VIDEO only).

FUNCTION +/ button
Press to select the “DVD,” “USB,”
“iPod,” “TUNER FM,” “TUNER AM” or
“VIDEO/SAT” function.

PICTURE NAVI button (page 45,
81)
Press to display the thumbnail pictures.

REPEAT/FM MODE button
(page 54, 65, 85)
Press to listen to a disc, a USB device, a
single track or file repeatedly.
Press to select FM reception mode
(monaural or stereo).

AUDIO button (page 40, 90, 99)
Press to select the desired audio signal on
the TV screen.
D. TUNING button (page 64)
Press to switch to the direct tuning mode.

MEMORY SELECT button
(page 85)
Press to select the playback source
or transferring destination on a Sony
Ericsson mobile phone.
Guide to parts and controls

ANGLE button (page 38)
Press to change the angle (DVD VIDEO
with multi-angles only).

+/ button (page 37)
Press to select a folder.

DVD/TUNER MENU button
(page 45, 65, 80)
Press to turn on or off the menu items on
the TV screen.
Press to preset the radio station.

SOUND FIELD button (page 89)
Press to select the sound field for the
surround sound.
Continued

17GB


VOLUME +/2) button
2) (play) button
Press to adjust the volume.
Press to adjust the TV volume.
/ (rewind/fast forward)
button

Press to find a point in a track, file,
chapter or video file.
TV VOL +/1)2) button
DISPLAY button (page 29, 34,
42, 74, 92)
SLOW/SLOW
button
Press to turn on or off the Control Menu
on the TV screen.
The Control Menu is displayed only
when the “DVD” function or “USB”
function is selected.
Press to watch the slow‑motion play.

Press to stop playback.
PRESET + button (page 65)
Press to select the preset station.
 (go forward) button
Press to select a track, chapter or video
file.
TV CH +1) button
Press to change the TV channels.
18GB
Press to start playback.
 (pause) button
Press to pause playback.
 (stop) button
TUNING +/ button
Press to tune in the desired station.

TV1) button
Press to operate the TV functions.

PRESET  button (page 65)
ENTER button
Press to select the preset station.
Press to enter the settings.
 (go backward) button

Press to select a track, chapter or video
file.
/// button
Press to select the menu items.
TV CH 1) button

Press to change the TV channels.

 STEP  button (page 37)
Press to play one frame at a time when
playback is paused.
ADVANCE
button (page 38)
Press to advance the current scene during
playback.
REPLAY button (page 38)
Press to replay the previous scene during
playback.

 RETURN button (page 46, 82)
Press to return to the previous menu on
the TV screen.
DVD TOP MENU button (page 37)
Press to display the DVD title on the TV
screen.

Guide to parts and controls

CLEAR button (page 35, 46, 51,
63, 76, 82)
Press to delete a pre-programmed track.
Press to erase files or folders from the
connected optional USB device.
Press to return to the original display
when viewing the rotated image.
Press to switch the TV’s input source
to “COMPONENT 3” while using
“THEATRE SYNC.”
-/--1) button
Press to enter a single-digit or doubledigit number.
Continued

19GB


Numeric buttons2)
DISPLAY button (page 32, 97)
Press to select a track, chapter or video
file number.
Press to enter a password.
Press to display the disc information or
clock in the front panel display.
10/01) button
TIME/TEXT button (page 98)
Press to enter a double-digit number.

Press to change the information on the
display.
KEY CONTROL  button
(page 91)

Press to change the key to suit your vocal
range.
Press to switch the input sources.
SCORE button (page 94)
Press to start or stop calculating your
vocal score.
KARAOKE MODE button
(page 91)
TV INPUT1) button
SLEEP button (page 95)
Press to set the Sleep Timer.

TIMER MENU button (page 32,
95)
Press to select the Karaoke mode.
Press to set the clock and the timers.
KARAOKE PON button (page 92)

Press to activate the “Karaoke Pon”
function.
20GB

THEATRE SYNC button (page 35)
Press to activate the “THEATRE SYNC”
function.
This button is used to operate a Sony TV. For
details, see “Operating a Sony TV” (page 31).
2)
The numeric button 5, TV VOL +,
VOLUME + and  buttons on the remote
have a tactile dot. Use the tactile dot as a
reference when operating the system.
1)
Guide to parts and controls
Continued

21GB
Display
The front panel display is liquid crystal display (LCD). You can confirm contents and the
Control Menu displayed on the TV screen in the LCD.
To set the LCD, see “Setting the LCD” (page 31).
Displays the text information.
22GB
You can confirm contents and the
Control Menu displayed on the TV
screen.
PICTURE MODE and WIDE MODE
menus are displayed when setting the
LCD.
Getting Started
 To front speaker (Right)
 AM loop antenna
 FM lead antenna (Extend it horizontally.)
Getting Started
Hooking up the system securely
 To front speaker (Left)
 To wall outlet
Continued

23GB
 FM/AM antennas
Find a location and an orientation that
provide good reception, and then set up
the antenna.
Keep the antennas away from the speaker
cords, the power cord and the USB cable
to avoid picking up noise.
 Speakers
Insert only the stripped portion of the
speaker cords.
The speaker cords are color-coded with
their respective speaker terminals.
The type of speakers supplied varies
according to the model you purchased.
Front speakers
Insert only the stripped
portion of the speaker cords
Red ()
Black ()
Note
Be sure to connect the speakers securely and
correctly.
24GB
 Voltage selector
For models with a voltage selector, set
VOLTAGE SELECTOR to the local
power line voltage.
 Power
Connect the power cord to a wall outlet.
The demonstration appears in the display.
When you press /, the system turns
on and the demonstration automatically
ends.
If the supplied adaptor on the plug does
not fit your wall outlet, detach it from the
plug (only for models equipped with an
adaptor).
Attaching the speaker pads
Front speakers (Left (4)/Right (4))
Slide and remove the battery
compartment lid, and insert the two
supplied R6 (size AA) batteries,  side
first, matching the polarities shown
below.
Getting Started
Attach the supplied speaker pads at each
corner on the bottom of the speakers to
prevent them from slipping.
Inserting batteries
Note
If you do not use the remote for a long period
of time, remove the batteries to avoid possible
damage from battery leakage and corrosion.
Tip
With normal use, the batteries should last for
about six months. When the remote no longer
operates the system, replace both batteries with
new ones.
Continued

25GB
When carrying this system
Perform the following procedure to
protect the DVD mechanism.
Use buttons on the unit for the operation.
1 Press / to turn on the system,
then press DVD.
2 Make sure that no disc is loaded
Using the iPod
Insert an iPod Dock Adapter into the
Dock before use. The iPod Dock Adapter
is not supplied with the system. Use
an iPod Dock Adapter supplied with
your iPod. For details on the iPod Dock
Adapter, refer to the user’s guide of your
iPod.
iPod Dock Adapter
in the system and check that
“NO DISC” appears.
3 Hold down , and then press
/ until “STANDBY” appears
in the display. Then, “LOCK”
appears in the display.
4 Unplug the power cord.
Connector
To remove the iPod Dock Adapter, pull
it up with your fingernail or a flat object
using the slot inside the adapter.
26GB
Hooking up the TV
Video deck
Unit
Do not connect
directly
When connecting to the COMPONENT
VIDEO OUT jack
For higher quality video images,
use the optional component video
cords to connect the COMPONENT
VIDEO input jacks on your TV to the
COMPONENT VIDEO OUT jacks
of this unit (page 101). If your TV is
compatible with progressive format
signals, use this connection and set
“PROGRESSIVE (COMPONENT
OUT)” to “ON” (page 29).
Getting Started
Connect the video input jack of your
TV to the VIDEO OUT jack with the
supplied video cord.
TV
Notes
You cannot output the video signal from the
VIDEO/SAT VIDEO IN jack through the
COMPONENT VIDEO OUT jacks of this
unit.
You cannot output the video signal from an
iPod through the COMPONENT VIDEO
OUT jacks of this unit.
When connecting a video deck
Connect the video deck to the TV using
a video cord (not supplied). However, do
not connect this unit to the TV through
the video deck. Otherwise, you may
experience video leakage when watching
video images from this system. Connect
this unit directly to the TV as shown
below.
Continued

27GB
Changing the color system
(Australian model only)
Set the color system of the DVD and
your iPod to PAL or NTSC depending on
the color system of your TV.
The default setting for color system is
different depending on the area.
Each time you perform the procedure
below, the color system changes as
follows:
NTSC  PAL
1 Press / to turn on the system.
2 Select the function.
For DVD color system:
Press FUNCTION +/ repeatedly to
select “DVD” (or press DVD on the
unit).
For iPod color system:
Press FUNCTION +/ repeatedly to
select “iPod” (or press iPod/OPR on
the unit).
3 Press / to turn off the system.
4 Press DISPLAY repeatedly until the
clock is displayed.
28GB
5 Press / on the unit while holding
down  on the unit.
The system turns on automatically and
the color system is changed.
“COLOR NTSC” or “COLOR PAL” (or
either “iPod COLOR NTSC” or “iPod
COLOR PAL”) appears in the display.
Note
You cannot change the color system for any
optional component connected to the VIDEO/
SAT VIDEO IN jack.
Changing the format of the
video signal output from
COMPONENT VIDEO OUT jacks
1 Press FUNCTION +/ repeatedly
to select “DVD” (or press DVD on
the unit).
“CUSTOM,” then press ENTER.
The Setup Menu appears.
5 Press  or  repeatedly to
select “VIDEO SETUP,” then press
ENTER.
The options for “VIDEO SETUP”
appear.
6 Press  or  repeatedly to select
Getting Started
Progressive is a method for displaying
TV images that reduces flickering and
sharpens the image. To use this method,
you need to connect to a TV that can
accept progressive signals.
You can output video signals from
COMPONENT VIDEO OUT jacks in
Interlace or Progressive format.
4 Press  or  repeatedly to select
“PROGRESSIVE (COMPONENT
OUT),” then press ENTER.
The options for “PROGRESSIVE
(COMPONENT OUT)” appear.
2 Press
DISPLAY when playback
is stopped.
The Control Menu appears on the TV
screen.
3 Press  or  repeatedly to
select
ENTER.
(SETUP), then press
The options for “SETUP” appear.
Continued

29GB
7 Press  or  repeatedly to select
the desired setting, then press
ENTER.
The default setting is underlined.
OFF: Outputs interlace signals.
Select this setting when:
 your TV does not accept
progressive signals.
 your TV is connected to jacks
other than the COMPONENT
VIDEO OUT jacks.
ON: Outputs progressive signals.
Select this setting when:
 your TV accepts progressive
signals.
 your TV is connected to the
COMPONENT VIDEO OUT
jacks.
When you select “ON,” the
confirmation display appears. Follow
the steps below.
30GB
8 Press  or  repeatedly to select
“START,” then press ENTER.
The system outputs the progressive
signal for 5 seconds. Check that the
screen is displayed correctly.
9 Press  or  repeatedly to select
“YES.”
The system outputs the progressive
signal. When you select “NO,”
the system does not output the
progressive signal.
Note
There would be no image on your TV or the
image is not clear if your setting does not
match your TV or connection.
When using a TV
Operating a Sony TV
You can use the following buttons to
operate a Sony TV. These buttons have
been marked in yellow.
To
Press
Turn the TV on
or off
Switch the TV’s
input source
between the TV
and other input
sources
Select the TV
channels
TV / while
holding down TV.
TV INPUT while
holding down TV.
TV CH +/ or
numeric buttons*
while holding down
TV.
Adjust the
TV VOL +/ while
volume of the TV holding down TV.
speaker(s)
You can make adjustments to pictures
displayed in the LCD.
Use buttons on the unit and confirm
operations in the LCD, for the following
settings.
Note
Playback settings stored in the disc take
priority over the LCD settings. Therefore, some
of the LCD settings may not be performed.
Getting Started
Turn on the TV and select the video
input so that you can view the pictures
from this system.
Setting the LCD
1 Press OPTIONS on the unit
repeatedly until “PICTURE
MODE” or “WIDE MODE” appears
in the LCD.
2 Press  or  repeatedly to select
the desired setting, then press
ENTER.
* For a double-digit number, while holding
down TV, press -/--, then press the number.
(For example, while holding down TV, press
-/--, then 2 and 5 to enter 25.)
Continued

31GB
Setting the LCD
The default setting is underlined.
PICTURE MODE
Allows you to select options best suited
for videos and pictures, respectively.
STANDARD: For standard pictures.
Recommended for home entertainment.
VIVID: Enhances picture contrast and
sharpness.
CINEMA: For viewing film-based
content.
PHOTO: For viewing photographs.
WIDE MODE
FULL: Select this when you view pictures
in a 16:9-format. This setting displays
pictures in full screen mode.
NORMAL: Select this when you view
pictures in a 4:3-format. This setting
displays a normal picture with bands on
the left and right portions of the screen.
Setting the clock
Use buttons on the remote to set the
clock.
1 Press / to turn on the system.
2 Press TIMER MENU.
The hour indication flashes in the
display.
If “PLAY SET?” flashes in the display,
press  or  repeatedly to select
“CLOCK SET?,” then press ENTER.
3 Press  or  repeatedly to set
the hour, and then press ENTER.
4 Use the same procedure to set
the minutes.
Note
The clock settings are canceled when you
disconnect the power cord or if a power failure
occurs.
To display the clock when the system
is off
Press DISPLAY repeatedly until the clock
is displayed.
The clock is displayed for about
8 seconds.
32GB
Performing “QUICK”
setup
4 Press ENTER without loading a
disc.
“LANGUAGE SETUP” appears on
the TV screen.
Getting Started
Before using the system, you can make
the minimum basic adjustments in
“QUICK” setup. If you do not want to
perform “QUICK” setup, press CLEAR in
step 3. The guide message will disappear
from the TV screen.
1 Turn on your TV and select the
video input*.
* This step is not required when using the
LCD for performing “QUICK” setup.
2 Press / to turn on the system.
5 Press  or  repeatedly to select
a language, then press ENTER.
The setting is selected and “VIDEO
SETUP” appears on the TV screen.
Notes
Tips
Make sure there is no disc in the unit.
Otherwise, the guide message does not
appear.
Make sure that the headphones or
microphones are not connected.
Otherwise, you cannot perform
“SPEAKER SETUP.”
The selected language is for “OSD,”
“MENU” and “SUBTITLE .”
The selectable language is different
depending on the area.
3 Press FUNCTION +/ repeatedly
to select “DVD” (or press DVD on
the unit).
The guide message appears at the
bottom of the TV screen.
Continued

33GB
6 Press  or  repeatedly to select
the setting that matches your TV
type.
If you have a 4:3 standard TV:
Select “4:3 LETTER BOX” or “4:3
PAN SCAN” (page 60).
If you have a wide-screen TV or a
4:3 standard TV with wide-screen
mode:
Select “16:9” (page 60).
7 Press ENTER.
The setting is selected and “QUICK
SETUP is complete.” appears on the
TV screen.
The system is ready for playback.
If you want to change each setting
individually, see “Using the Setup
Menu” (page 58).
If you make a mistake
Press , then select the item again.
To quit “QUICK” setup
Press
34GB
DISPLAY.
To recall “QUICK” setup settings
1 Press
DISPLAY when playback is
stopped.
The Control Menu appears on the TV
screen.
2 Press  or  repeatedly to select
(SETUP), then press ENTER.
3 Press  or  repeatedly to select
“QUICK,” then press ENTER.
Note
The guide message appears at the bottom of
the TV screen when you turn on the system
for the first time or after performing “RESET”
(page 116).
Operating the “THEATRE SYNC”
function
Using the “THEATRE
SYNC” function
Preparing to use the “THEATRE
SYNC” function
Register the TV’s input source connected
to this system.
To select the TV’s input
Press the following buttons while holding
down SLEEP.
Press
0
TV’s input source
No input source
(Default)
1 to 8
9
CLEAR

VIDEO 1 to VIDEO 8
COMPONENT 1
COMPONENT 2
COMPONENT 3
+
COMPONENT 4
Keeping the remote pointed in the
direction of the TV, press THEATRE
SYNC until the TV turns on and the
selected input source changes.
If this function does not work, change the
transmission time. The transmission time
varies depending on the TV.
Getting Started
THEATRE SYNC allows you to turn on
your Sony TV and this system, changes
the system’s function to “DVD” and then
switches the TV’s input source you have
set with just one button.
To change the transmission time
Press the following buttons while holding
down .
Press
1
2
3
4
5
6
7
8
Transmission time
(seconds)
0.5 (Default)
1
1.5
2
2.5
3
3.5
4
Note
This function is only for Sony TV series,
however, some TV products may also not work.
The selected TV’s input source is
memorized into the remote.
35GB
Disc
Playing a disc
3 Load a disc with the label side
facing up on the disc tray.
To load additional discs, press DISC
SKIP/EX-CHANGE on the unit to
rotate the disc tray.
Depending on the DVD VIDEO or
VIDEO CD, some operations may
be different or restricted. Refer to the
operating instructions supplied with the
disc.
DivX and MPEG4 video files can only be
played back on MHC-GZR333i.
Note on the maximum number of
tracks, files and folders on a DATA
CD/DVD
This system cannot play a DATA CD/
DVD in the following cases.
When the number of tracks or files on
a folder exceeds 150.
When the number of folders on a disc
exceeds 200.
These numbers may vary depending on
the track structure, the file structure and
the folder structure.
1 Press FUNCTION +/ repeatedly
to select “DVD” (or press DVD on
the unit).
2 Press OPEN/CLOSE  on the
unit.
When you play back an 8 cm disc such as a CD
single, place it on the inner circle of the tray.
4 Press OPEN/CLOSE  on the
unit to close the disc tray.
Do not forcibly push the disc
tray to close it as this may cause a
malfunction.
If the playback does not start
automatically, press  (or  on
the unit).
5 Press VOLUME +/ (or turn
MASTER VOLUME on the unit) to
adjust the volume.
Note
Depending on the system status, the volume
level may not appear on the TV screen.
36GB
Other operations
To
Stop playback
Continued

Disc
Do this
Press . To resume
playback where you
stopped the disc, press
 (or  on the
unit). To play back
from the beginning of
the disc, press  twice,
then press  (or 
on the unit).
Pause playback Press 1). Press 
again or press  (or
 on the unit) to
resume playback.
Select a track, Press  or 
audio file,
repeatedly (or turn
chapter or
OPERATION DIAL
video file2)
on the unit clockwise
or counterclockwise)
during playback.
Or, press the numeric
buttons when the
Control Menu is
turned off, then press
ENTER3).
Select a title4) Press DVD TOP
MENU, then press
/// or numeric
buttons.
To
Do this
Select a folder5) Press
+/
repeatedly during
playback or when
playback is paused.
Locate a point Press  or 
quickly in fast during playback.
forward or fast Each time you press
reverse (Lock  or , the
Search)6)
playback speed changes
cyclically7).
To return to normal
playback, press  (or
 on the unit).
Watch frame by Press
SLOW9) or
frame (SlowSLOW
(or either
9)
motion Play)8)
or
on the
unit) when playback is
paused.
Each time you
press
SLOW or
SLOW , the playback
speed changes.
To return to normal
playback, press  (or
 on the unit).
Play one
Press  STEP9) or
frame at a
STEP  to reverse
time (Freeze
or advance frame by
Frame)8)
frame when playback is
paused.
Each time you press
 STEP or STEP ,
the frame changes.
To return to normal
playback, press  (or
 on the unit).
37GB
To
Replay the
previous scene
(Instant
Replay)10)
Briefly fast
forward the
current scene
(Instant
Advance)10)
Change the
angle11)
Do this
Press
REPLAY
during playback.
Press ADVANCE
during playback.
Press ANGLE
repeatedly during
playback. Each time
you press ANGLE, the
angle changes.
Display the
Press SUBTITLE
subtitle
repeatedly during
playback. Each time
you press SUBTITLE,
the subtitle language
changes12) or turns
off13).
Select a disc
Press DISC SKIP (or
one of DISC 1  DISC
3 on the unit).
Switch to
Press one of DISC 1
“DVD”
 DISC 3 on the unit
function from (Automatic Source
another source Selection).
Exchange other Press DISC SKIP/EXdiscs while
CHANGE on the unit.
playing
38GB
There may be some disturbance in the video
image.
2)
Except for JPEG image files. You cannot
select an audio track or file during Lock
Search operation of MP3 files.
3)
DVD VIDEO, DVD-R/-RW in VR mode,
VIDEO CD, AUDIO CD and video files only.
4)
DVD VIDEO only.
5)
MP3 files, JPEG image files, DivX video files
and MPEG4 video files only.
6)
Except for JPEG image files.
7)
Depending on the disc, the actual speed may
differ.
8)
DVD VIDEO, DVD-R/-RW in VR mode,
video files and VIDEO CD only.
9)
Except for VIDEO CD and video files.
10)
DVD VIDEO and DVD-R/-RW in VR mode
only.
11)
Multi-angle DVD VIDEO only.
12)
For DVD VIDEO, DVD-R/-RW in VR
mode or DivX video files with multilingual
subtitles.
13)
For DVD VIDEO, DVD-R/-RW in VR mode
or DivX video files with subtitles.
1)
Notes
On Multi-disc Resume
(DVD VIDEO and VIDEO CD only)
This system can store the point where
you stopped the playback of the disc for
up to 6 discs and resumes playback when
you insert the same disc again. If you
store a playback resume point for the 7th
disc, the playback resume point for the
first disc will be deleted.
The default setting is “ON.” To turn
off this function, set “MULTI-DISC
RESUME” in “SYSTEM SETUP” to
“OFF” (page 63).
Disc
You cannot perform resume playback during
Shuffle Play or Program Play.
Resume playback may not work properly
with some discs.
Resume playback is canceled when
 you press  when playback is stopped.
 you open the disc tray.
 you change the function.
 you change the settings in the Setup
Menu.
 you changed the “PARENTAL
CONTROL” level.
You cannot search for a still picture on a
DVD-R/-RW in VR mode.
You may not be able to use the Instant Replay
or Instant Advance function in Repeat Play
mode or with some scenes.
Depending on the DVD VIDEO, you may
not be able to change the angle, even if multiangles are recorded on the DVD VIDEO.
Depending on the DVD VIDEO, you may
not be able to change the subtitles even if
multilingual subtitles are recorded on the
DVD VIDEO. You also may not be able to
turn the subtitles off.
You can change the subtitles if the DivX
video file has an “.avi” or “.divx” extension
and contains subtitle information within the
same file.
Notes
If “MULTI-DISC RESUME” in “SYSTEM
SETUP” is set to “ON” and you play back a
recorded disc such as DVD-R, the system
may play back other recorded discs from
the same playback resume point. To start
playback from the beginning of the disc,
press  twice and then press  (or  on
the unit).
The playback resume point is deleted when
the power cord is disconnected.
Continued

39GB
Changing the language/sound
Press AUDIO repeatedly during
playback to select the desired
audio format or mode.
The default setting is underlined.
When playing a DVD VIDEO:
Depending on the DVD VIDEO, the
option of language and audio format
varies.
When a 4-digit number is displayed, the
digits represent a language code (see
“Language code list” (page 134)). When
the same language is displayed two or
more times, the DVD VIDEO is recorded
in multiple audio formats. Note that the
sound changes automatically depending
on the disc.
Some DVD VIDEOs allow you to select
items such as the language for the
subtitles and the language for the sound
using DVD/TUNER MENU.
When playing a DivX video file
(MHC‑GZR333i only):
The options for audio format differ
depending on the DivX video files.
When playing a DVD-R/-RW in VR
mode:
The number of audio tracks recorded on
a disc are displayed.
Example:
1: MAIN: the main sound of the audio
track 1.
1: SUB: the sub sound of the audio
track 1.
40GB
1: MAIN+SUB: the main and sub
sound of the audio track 1.
2: MAIN*: the main sound of the audio
track 2.
2: SUB*: the sub sound of the audio
track 2.
2: MAIN+SUB*: the main and sub
sound of the audio track 2.
* These items do not appear if only one audio
stream is recorded on the disc being played
back.
When playing a VIDEO CD, AUDIO CD,
or MP3 file:
You can select the sound from the right
or left channel and listen to the sound
of the selected channel through both
the right and left speakers. For example,
when playing a track with the vocals on
the right channel and the instruments
on the left channel, you can hear the
instruments from both speakers by
selecting the left channel.
STEREO: the standard stereo sound.
1/L: the sound of the left channel
(monaural).
2/R: the sound of the right channel
(monaural).
Note
While the system is playing a Super VCD
on which the audio track 2 is not recorded,
no sound will come out when you select
“2: STEREO,” “2: 1/L” or “2: 2/R.”
Playing VIDEO CDs with PBC
functions (PBC Playback)
(Version 2.0)
You can use the PBC (Playback Control)
menus included on the VIDEO CDs
(Version 2.0 only) on your TV screen to
enjoy the disc’s interactive software. The
menu format and structure may differ
depending on each disc.
Disc
When playing a Super VCD:
1: STEREO: the stereo sound of the
audio track 1.
1: 1/L: the sound of the left channel of
the audio track 1 (monaural).
1: 2/R: the sound of the right channel
of the audio track 1 (monaural).
2: STEREO: the stereo sound of the
audio track 2.
2: 1/L: the sound of the left channel of
the audio track 2 (monaural).
2: 2/R: the sound of the right channel
of the audio track 2 (monaural).
1 Press  (or  on the unit) to
start playing a VIDEO CD.
The PBC menu appears on the TV
screen. Depending on the VIDEO
CD, the menu may not appear.
2 Press the numeric buttons to
select the desired item number.
3 Press ENTER.
Depending on the VIDEO CD,
“Press ENTER” may appear as
“Press SELECT” in the operating
instructions supplied with the disc.
In this case, press  (or  on the
unit).
Continued

41GB
4 Continue playback according to
the instructions on the menus.
Refer to the operating instructions
supplied with the VIDEO CD, as
the operating procedure may differ
depending on the VIDEO CD.
Note
PBC playback is canceled when Shuffle Play,
Program Play or Repeat Play is activated.
To cancel playback with PBC
functions
1 Press  or  repeatedly or
press the numeric buttons to select a
track when playback is stopped.
2 Press  (or  on the unit) or
ENTER.
Playback starts from the selected track.
Still images, such as the menu screens,
will not be shown.
To return to PBC playback, press 
twice, then press  (or  on the
unit).
Selecting “ORIGINAL” or “PLAY
LIST”
This function is only available for DVDRs/-RWs in VR mode with a playlist
created.
1 Press
DISPLAY when playback
is stopped.
The Control Menu appears on the TV
screen.
2 Press  or  repeatedly to select
(ORIGINAL/PLAY LIST),
then press ENTER.
The options for “ORIGINAL/PLAY
LIST” appear on the TV screen.
3 Press  or  repeatedly to select
the desired setting.
PLAY LIST: play back according to
the playlist created on the disc.
ORIGINAL: play back according to
the originally recorded sequence.
4 Press ENTER.
42GB
Searching for items on a disc by
the assigned numbers
1 Press
DISPLAY.
The Control Menu appears on the TV
screen.
If “MEDIA” is set to “MUSIC/
PHOTO” and “FILE” does not
appear in the Control Menu, press
DISPLAY again.
“** (**)” change to “– – (**).”
4 Press  or  repeatedly or the
numeric buttons to select the
title, track, folder or file, etc.
If you make a mistake, press CLEAR
to cancel the number.
5 Press ENTER.
Disc
You can search by different information
recorded on a disc, such as title, track,
scene, file, and folder. Each item is
assigned a unique number on the disc,
and you can select the numbered item
you want from the Control Menu. You
can also search for a particular point
using the time code (Time Search) (DVD
VIDEO and DVD-R/-RW in VR mode
only).
3 Press ENTER.
The system starts playback from the
selected title, track, folder or file, etc.
Tip
When the Control Menu display is turned off,
you can search for a chapter (DVD VIDEO and
DVD-R/-RW in VR mode) or track (AUDIO
CD and VIDEO CD) or file (video files in
DATA CD/DVD) by pressing the numeric
buttons and ENTER.
2 Press  or  repeatedly to select
the search item.
Example: when you select
(CHAPTER)
“** (**)” is selected (** refers to a
number). The number in parentheses
indicates the total number of titles,
chapters, tracks, index, scenes, folders
or files.
Selected row
Continued

43GB
To search for a particular point using
the time code (Time Search)
(DVD VIDEO and DVD-R/-RW in VR
mode only)
1 Press
DISPLAY.
2 Press  or  repeatedly to select
(TIME).
“T **:**:**” (elapsed playing time of
the current title) is selected.
3 Press ENTER.
“T **:**:**” changes to “T--:--:--.”
4 Input the time code using the
numeric buttons, then press ENTER.
For example, to find the scene at 2
hours, 10 minutes, and 20 seconds
after the beginning, enter “21020.”
If you make a mistake, press CLEAR to
cancel the number.
Note
Depending on the disc, you cannot perform
Time Search.
Selecting a folder/file using
the on-screen display
DivX and MPEG4 video files can only be
played back on MHC-GZR333i.
1 Load a disc on the disc tray.
“FOLDER LIST” appears on the TV
screen.
2 Press
DISPLAY.
The Control Menu appears on the TV
screen.
3 Press  or  repeatedly to select
* (MEDIA), then press
ENTER.
The options for “MEDIA” appear on
the TV screen.
*
appears on LBT-LCD77Di.
MUSIC/PHOTO: for playing both
MP3 files and JPEG image files in
the same folder as a slide show
MUSIC: for playing MP3 files
VIDEO1): for playing DivX video
files or MPEG4 video files
PHOTO: for playing JPEG image
files
MHC-GZR333i only.
1)
44GB
4 Press  or  repeatedly to select
the desired option, then press
ENTER. When the desired option
has already been selected, press
DVD/TUNER MENU.
Playing an image file:
1 Press PICTURE NAVI.
Thumbnail picture for the first
16 JPEG image files in the selected
folder is displayed.
Disc
A list of folders that contains the files
of the selected file type appears on the
TV screen.
5 Press  or  repeatedly to select
a folder.
Playing a folder:
Press  (or  on the unit).
The system starts playback from the
first file of the selected folder.
To stop playback, press .
Playing an MP3 file:
1 Press ENTER.
“TRACK LIST” appears.
If there are more than 16 image
files in the selected folder, the scroll
bar appears at the right.
2 Press /// repeatedly to
select the image you want to
view, then press  (or  on
the unit).
The slide show starts from the
selected image file.
To stop playback, press .
The slide show stops when you
press  or .
2 Press  or  repeatedly to select
the desired MP3 file, then press
ENTER.
The system starts playing the
selected MP3 file.
To stop playback, press .
Continued

45GB
Playing a video file:
1 Press ENTER.
“FILE LIST” appears.
2 Press  or  repeatedly to select
the desired video file, then press
ENTER.
The system starts playback of the
selected video file.
To stop playback, press .
Other operations
To
Display
the next or
previous page
of “TRACK
LIST,”
“FOLDER
LIST” or “FILE
LIST”
Play back the
next folder of
MP3 files or
video files
Return to
“FOLDER
LIST” when
“TRACK LIST,”
or “FILE LIST”
is displayed
Play back the
next folder of
JPEG image
files
Rotate the
image by
90 degrees
46GB
Do this
Press
or
repeatedly.
Press  repeatedly
until the last file of the
current folder, then
press  once. To
select the previous
folder, select the folder
from “FOLDER LIST.”
Press  RETURN.
Press  repeatedly
until the last file of the
current folder, then
press  once. To select
the previous folder,
select the folder from
“FOLDER LIST.”
Press  or  repeatedly
while viewing an
image. To return to
the original view, press
CLEAR.
Notes
The system may not play certain types of
JPEG image files (ex. a JPEG image file that is
less than 8 (width) × 8 (height) pixels).
When you press  or  to select the next or
previous image, the image will return to its
original view even if you have rotated the
image previously.
The slide show stops when you press  or .
The system may not play back a video file
when the file has been combined from two or
more video files.
The system cannot play back any video file
that is more than 720 (width) × 576 (height)
pixels in resolution or 2 GB in file size or
larger.
Depending on the video file, the picture may
be unclear or the sound may skip.
The system cannot play back some video files
that are longer than 3 hours.
Depending on the video file, the picture
may pause or be unclear. In this case, it is
recommended that you create the file at a
lower bit rate.
Due to the compression technology used for
video files, it may take some time after you
press  for the picture to appear.
Depending on the video file, the sound may
not match the pictures on the screen.
Continued

Disc
The system can play back MP3 files and
JPEG image files. The system will play back
any data with the extension “.mp3”, “.jpg” or
“.jpeg” even if they are not in MP3 or JPEG
format. Playing this data may generate a
loud noise which could damage your speaker
system.
Depending on the encoding/writing
software, recording device, or the recording
media used to record an MP3 file, you may
encounter problems such as cannot play
back, sound interruptions and noise.
The following discs/situations can increase
the time it takes to start playback:
 a disc recorded with a complicated tree
structure.
 a disc recorded in Multi Session.
 a disc to which data can be added (nonfinalized disc).
 when the tracks or files in another folder
have just been played back.
Some CD-Rs/-RWs or DVD-Rs/-RWs/+Rs/
+RWs cannot be played back on the system
depending on the file format.
The system can play back to a depth of
8 folders only.
47GB
Tip
If the number of viewing times has been preset,
you can play back the DivX video files as many
times as the preset number. The following
occurrences are counted:
 when the system is turned off.
 when the disc is removed.
 when another video file is played back.
To play MP3 files and JPEG image files
as a slide show with sound
(DATA CD and DATA DVD only)
You can play back a slide show with
sound by first placing both JPEG image
files and MP3 files in the same folder on a
DATA CD/DVD.
1 Press
DISPLAY when playback is
stopped.
The Control Menu appears on the TV
screen.
2 Press  or  repeatedly to select
* (MEDIA), then press ENTER.
The options for “MEDIA” appear on
the TV screen.
*
48GB
appears on LBT-LCD77Di.
3 Press  or  repeatedly to select
“MUSIC/PHOTO,” then press ENTER.
When “MUSIC/PHOTO” has already
been selected, press DVD/TUNER
MENU.
“FOLDER LIST” appears on the TV
screen.
4 Press  or  repeatedly to select the
desired folder, then press  (or 
on the unit).
The slide show with sound starts from
the selected folder.
To stop playback, press .
To cancel the slide show with sound,
select “MUSIC” or “PHOTO” in
step 3.
Note
If you play back a large data size of MP3 files
and JPEG image files at the same time, the
sound may skip.
To specify the slide show speed
(JPEG image files only)
1 Press
2 Press  or  repeatedly to select
(INTERVAL), then press ENTER.
The options for “INTERVAL” appear
on the TV screen.
3 Press  or  repeatedly to select the
desired transition interval.
The default setting is underlined.
NORMAL: Sets to the standard
duration.
FAST: Sets the duration shorter
than “NORMAL.”
SLOW 1: Sets the duration longer
than “NORMAL.”
SLOW 2: Sets the duration longer
than “SLOW 1.”
4 Press ENTER.
The selected setting takes effect.
Note
Some JPEG image files (especially progressive
JPEG image files or JPEG image files with
3,000,000 pixels or more) may take a longer
time to display than others, which may make
the transitions seem longer than that of the
option you selected.
(JPEG image files only)
1 Press
DISPLAY.
The Control Menu appears on the TV
screen.
If “MEDIA” is set to “MUSIC/
PHOTO” and “EFFECT” does not
appear in the Control Menu, press
DISPLAY again.
Disc
DISPLAY.
The Control Menu appears on the TV
screen.
If “MEDIA” is set to “MUSIC/
PHOTO” and “INTERVAL” does not
appear in the Control Menu, press
DISPLAY again.
To select a transition effect for image
files in the slide show
2 Press  or  repeatedly to select
(EFFECT), then press ENTER.
The options for “EFFECT” appear on
the TV screen.
3 Press  or  repeatedly to select the
desired setting.
The default setting is underlined.
MODE 1: The image sweeps in
from top to bottom of the screen.
MODE 2: The image sweeps in
from left to right of the screen.
MODE 3: The image stretches out
from the center of the screen.
MODE 4: The image randomly
cycles through the effects.
MODE 5: The next image slides
over the current image.
OFF: Turns off this function.
4 Press ENTER.
The selected setting takes effect.
Continued

49GB
To select playback priority of the file
type
You can select playback priority when
mixed media (MP3 files, JPEG image files
or video files) are in the disc.
1 Press
DISPLAY.
The Control Menu appears on the TV
screen.
2 Press  or  repeatedly to select
* (MEDIA), then press ENTER.
The options for “MEDIA” appear on
the TV screen.
*
appears on LBT-LCD77Di.
3 Press  or  repeatedly to select the
desired setting.
MUSIC/PHOTO: You can play
back a slide show with sound, when
MP3 files and JPEG image files are
in the same folder.
MUSIC: MP3 file playback has
priority.
VIDEO1): Video file playback has
priority.
PHOTO: JPEG image file playback
has priority.
MHC-GZR333i only.
1)
Using play mode
Creating your own program
(Program Play)
You can make a program of up to 99
steps in the order you want them to be
played back.
You can only program the tracks from
the current disc.
1 Press
DISPLAY when playback
is stopped.
The Control Menu appears on the TV
screen.
2 Press  or  repeatedly to select
(PROGRAM), then press
ENTER.
The options for “PROGRAM” appear
on the TV screen.
3 Press  or  repeatedly to select
“SET ,” then press ENTER.
4 Press ENTER.
The selected setting takes effect.
For further details of the playback
priority of file types, see page 133.
Track number
50GB
4 Press .
The cursor moves to the track list “T”
(in this case, “01”).
7 Press  (or  on the unit).
Program Play starts.
When the Program Play ends, you
can restart the same program by
pressing  (or  on the unit).
5 Select the track you want to
program.
For example, select track “02.”
Press  or  repeatedly to select “02”
under “T,” then press ENTER.
Selected track
Disc
To change a programmed step:
Press  or  repeatedly to select the
programmed step number you want
to change. Then, press  and select
the desired track number.
To delete a programmed step:
Press  or  repeatedly to select the
programmed step number you want
to delete. Then, press CLEAR.
To delete all of the programmed
steps in the program list:
Press  to select “ALL CLEAR.” Then,
press ENTER.
To cancel Program Play
Press CLEAR or select “OFF” in step 3.
To play back the same program again,
select “ON” in step 3 and press ENTER.
Total time of the programmed tracks
6 To program other tracks, repeat
steps 4 and 5.
Continued

51GB
Notes
When Program Play is activated, the
“REPEAT” setting is automatically changed
to “ON” if the current setting is “ALL DISCS,”
“ONE DISC” or “TRACK.”
You cannot perform Program Play with
VIDEO CDs during PBC playback.
Tip
The Program Play is canceled and the program
list is cleared when
 you open the disc tray.
 you change the disc.
 you turn off the system.
 you change the function.
Playing in random order
(Shuffle Play)
You can play back the tracks on the
current disc in random order. Each time
you perform Shuffle Play, the playing
order may differ.
Shuffle Play is only available for the
tracks on the current disc.
1 Press
DISPLAY.
The Control Menu appears on the TV
screen.
2 Press  or  repeatedly to select
(SHUFFLE), then press
ENTER.
The options for “SHUFFLE” appear
on the TV screen.
3 Press  or  repeatedly to select
the desired setting.
When playing a VIDEO CD or
AUDIO CD:
TRACK: all tracks on the current
disc are played back randomly.
When Program Play is activated:
ON: all tracks in the program list
are played back randomly.
52GB
When playing a DATA CD/DVD
(except for video files):
ON (MUSIC): all MP3 files in the
selected folder on the current disc
are played back randomly.
When no folder is selected, the first
folder is played back randomly.
Shuffle Play starts.
To cancel Shuffle Play, press CLEAR
or select “OFF” in step 3.
Notes
You cannot perform Shuffle Play with
VIDEO CDs during PBC playback.
The same song may be played back
repeatedly for MP3 files.
Tip
Shuffle Play is canceled when
 you open the disc tray.
 you change the disc.
 you turn off the system.
 you change the function.
 you perform Track/Index Search.
 you perform USB TRANSFER.
 you transfer music from a disc to a USB
device.
You can play the contents on a disc
repeatedly.
You can also repeat Shuffle Play or
Program Play.
1 Press
Disc
4 Press ENTER.
5 Press  (or  on the unit).
Playing repeatedly (Repeat
Play)
DISPLAY.
The Control Menu appears on the TV
screen.
2 Press  or  repeatedly to select
(REPEAT), then press
ENTER.
The options for “REPEAT” appear on
the TV screen.
3 Press  or  repeatedly to select
the desired setting.
The default setting is underlined.
When playing a DVD VIDEO or
DVD-R/DVD-RW in VR mode:
OFF: does not play back repeatedly.
ALL DISCS: repeats all discs.
ONE DISC: repeats all the titles on
the current disc.
TITLE: repeats the current title.
CHAPTER: repeats the current
chapter.
Continued

53GB
When playing a VIDEO CD or
AUDIO CD:
OFF: does not play back repeatedly.
ALL DISCS: repeats all discs.
ONE DISC: repeats all the tracks
on the current disc.
TRACK: repeats the current track.
When playing a DATA CD or DATA
DVD:
OFF: does not play back repeatedly.
ALL DISCS: repeats all discs.
ONE DISC: repeats all the folders
on the current disc.
FOLDER: repeats the current
folder.
TRACK1): repeats the current audio
file.
FILE2): repeats the current file.
MP3 files only.
Video files only.
1)
2)
When Program Play or Shuffle
Play is activated:
OFF: does not play back repeatedly.
ON: repeats the Program Play or
Shuffle Play.
4 Press ENTER.
5 Press  (or  on the unit).
Repeat Play starts.
To cancel Repeat Play, press CLEAR
or select “OFF” in step 3.
54GB
Notes
You can also change the Repeat Play setting
by pressing REPEAT/FM MODE repeatedly.
Depending on the DVD VIDEO, you cannot
perform Repeat Play.
You cannot perform Repeat Play with
VIDEO CDs during PBC playback.
When playing a DATA CD/DVD which
contains MP3 files and JPEG image files, the
audio sound will not match the image if their
playing time are different.
Repeat Play is canceled when
 you open the disc tray.
 you change the disc (except when “ALL
DISCS” is selected).
 you turn off the system.
 you change the function (except when
“ALL DISCS” is selected).
 you perform USB TRANSFER.
 you transfer music from a disc to a USB
device.
Adjusting the delay
between the picture
and sound (“A/V SYNC”)
1 Press
Depending on the input stream, this function
may not be effective.
Disc
When the sound does not synchronize
with the pictures on the screen, you can
adjust the delay between the picture and
sound.
“A/V SYNC” does not work for MP3 files
and JPEG image files in DATA CD/DVD.
Note
DISPLAY.
The Control Menu appears on the TV
screen.
2 Press  or  repeatedly to select
(A/V SYNC), then press
ENTER.
The options for “A/V SYNC” appear
on the TV screen.
3 Press  or  repeatedly to select
the desired setting.
The default setting is underlined.
OFF: Does not adjust.
ON: Adjusts the difference between
picture and sound.
4 Press ENTER.
55GB
Restricting playback
of the disc (PARENTAL
CONTROL)
You can limit the playback of some DVD
VIDEOs according to a predetermined
level such as the age of the users. When
a limited scene is played back, that scene
may be skipped or replaced with different
scenes.
5 Press  or  repeatedly to select
“PARENTAL CONTROL,” then
press ENTER.
If you have not registered a
password:
The display for registering a new
password appears on the TV screen.
1 Press
DISPLAY when playback
is stopped.
The Control Menu appears on the TV
screen.
2 Press  or  repeatedly to
select
ENTER.
(SETUP), then press
The options for “SETUP” appear on
the TV screen.
3 Press  or  repeatedly to select
“CUSTOM,” then press ENTER.
The Setup Menu appears on the TV
screen.
4 Press  or  repeatedly to select
“SYSTEM SETUP,” then press
ENTER.
56GB
Enter a 4-digit password using the
numeric buttons, then press ENTER.
The display for confirming the
password appears on the TV screen.
When you have already registered
a password:
The display for entering the password
appears on the TV screen.
If you make a mistake when
entering your password:
Press  repeatedly to delete the
number you have entered, then
re‑enter your password again.
6 Enter or re-enter your 4-digit
password using the numeric
buttons, then press ENTER.
The display for setting the playback
limitation level appears on the TV
screen.
9 Press  or  repeatedly to select
“LEVEL,” then press ENTER.
The options for “LEVEL” appear on
the TV screen.
10Press  or  repeatedly to select
“PARENTAL CONTROL” setting is
completed.
The lower the value, the stricter the
limitation.
7 Press  or  repeatedly to select
“STANDARD,” then press ENTER.
The options for “STANDARD” appear
on the TV screen.
8 Press  or  repeatedly to
select a geographic area as the
playback limitation level, then
press ENTER.
The area is selected.
When you select “OTHERS ,”
enter the area code for the geographic
area you want by using the numeric
buttons (see “Parental Control area
code list” (page 135)).
Disc
the desired level, then press
ENTER.
To turn off the “PARENTAL CONTROL”
function
Set “LEVEL” to “OFF” in step 10.
To change the password
1 Press  or  repeatedly to select
“CHANGE PASSWORD,” then press
ENTER in step 7 of “Restricting
playback of the disc.”
2 Enter your 4-digit password using the
numeric buttons, then press ENTER.
3 Enter a new 4-digit password using
the numeric buttons, then press
ENTER.
4 To confirm your password, re-enter
it using the numeric buttons, then
press ENTER.
Continued

57GB
If you forget your password
Remove the disc and repeat steps 1 to
5 of “Restricting playback of the disc
(PARENTAL CONTROL)” (page 56).
When you are asked to enter your
password, enter “199703” using the
numeric buttons, then press ENTER. The
display will ask you to enter a new 4-digit
password. After you enter a new 4-digit
password, reload the disc and press 
(or  on the unit). When the display
for entering your password appears, enter
your new password.
To play back a disc for which
“PARENTAL CONTROL” is set
1 Load the disc and press  (or 
on the unit).
The display for entering your password
appears on the TV screen.
2 Enter your 4-digit password using the
numeric buttons, then press ENTER.
The system starts playback.
Notes
When you play back DVD VIDEOs which
do not have the “PARENTAL CONTROL”
function, playback cannot be limited on this
system.
Depending on the DVD VIDEO, you
may be asked to change the “PARENTAL
CONTROL” level while playing the disc. In
this case, enter your password, then change
the level. If resume playback is canceled, the
level returns to the original level.
58GB
Using the Setup Menu
By using the Setup Menu, you can make
various adjustments to items such as
picture and sound.
Displayed items vary depending on the
country or region.
Note
Playback settings stored in the disc take
priority over the Setup Menu settings.
Therefore, some of the Setup Menu settings
may not be performed.
1 Press
DISPLAY when playback
is stopped.
The Control Menu appears on the TV
screen.
2 Press  or  repeatedly to
select
ENTER.
(SETUP), then press
The options for “SETUP” appear on
the TV screen.
3 Press  or  repeatedly to select
“CUSTOM,” then press ENTER.
The Setup Menu appears on the TV
screen.
4 Press  or  repeatedly to
6 Press  or  repeatedly to select
The setup item is selected.
The setting is selected and setup is
completed.
select the setup item from the
displayed list, then press ENTER.
Disc
Setup items:
: LANGUAGE SETUP
: VIDEO SETUP
: AUDIO SETUP
: SYSTEM SETUP
: SPEAKER SETUP
the desired setting, then press
ENTER.
Selected setting
Example: “VIDEO SETUP”
Selected item
Setting the language
 “LANGUAGE SETUP”
Set various languages for the on-screen
display or sound track.
Setup items
5 Press  or  repeatedly to select
the desired item, then press
ENTER.
The options for the selected item
appear on the TV screen.
Example: “TV TYPE”
OSD
(On-Screen Display)
Switches the language of the on-screen
display.
MENU*
(DVD VIDEO only)
Select the language for the DVD menu.
Options
Continued

59GB
AUDIO*
(DVD VIDEO only)
Switches the language of the sound track.
When you select “ORIGINAL,” the
language given priority in the disc is
selected.
SUBTITLE*
(DVD VIDEO only)
Switches the language of the subtitle.
When you select “AUDIO FOLLOW,”
the language for the subtitles changes
according to the language you selected
for the sound track.
Setting the TV screen
 “VIDEO SETUP”
Choose the settings according to the TV
you connected.
The default setting is underlined.
TV TYPE1)
(DVD VIDEO only)
16:9: Select this when you connect a
wide-screen TV or a TV with a wide
mode function.
* When you select a language in “MENU,”
“AUDIO,” or “SUBTITLE” that is not
recorded on the DVD VIDEO, one of the
recorded language is automatically selected.
However, depending on the disc, the
language may not be selected automatically.
If you select “OTHERS ” in “MENU,”
“AUDIO,” and “SUBTITLE,” enter a language
code using the numeric buttons (see
“Language code list” (page 134)).
4:3 LETTER BOX: Select this when you
connect a 4:3 screen TV. This setting
displays a wide picture with bands on the
upper and lower portions of the screen.
4:3 PAN SCAN2): Select this when you
connect a 4:3 screen TV. This setting
displays the wide picture on the entire
screen and cuts off the portions that do
not fit.
60GB
COLOR SYSTEM (VIDEO CD)
(Australian model only)
Select the output video signal when you
play back a VIDEO CD.
AUTO: Outputs the video signal
according to the color system of the disc,
either PAL or NTSC.
PAL: Changes the video signal of an
NTSC disc and output it in PAL system.
NTSC: Changes the video signal of a PAL
disc and output it in NTSC system.
BLACK LEVEL
(North American and Latin American
models only)
Selects the black level (setup level) for the
video signals output from the jacks other
than COMPONENT VIDEO OUT.
ON: Sets the black level of the output
signal to the standard level.
OFF: Lowers the standard black level.
Use this when the picture becomes too
white.
BLACK LEVEL (COMPONENT OUT)
(North American and Latin American
models only)
Selects the black level (setup level)
for the video signals output from the
COMPONENT VIDEO OUT jacks.
“BLACK LEVEL (COMPONENT OUT)”
setting is not available when the system
outputs progressive signal.
OFF: Sets the black level of the output
signal to the standard level.
ON: Raises the standard black level. Use
this when the picture becomes too black.
Disc
PROGRESSIVE (COMPONENT OUT)
Sets the progressive signal output from
the COMPONENT VIDEO OUT jacks
to on or off.
OFF: Outputs interlace signals.
ON: Outputs progressive signals.
For details, see “Changing the format
of the video signal output from
COMPONENT VIDEO OUT jacks”
(page 29).
PAUSE MODE
(DVD VIDEO and DVD-R/-RW in VR
mode only)
AUTO: The picture, including subjects
that move dynamically, is output with no
jitter. Normally select this position.
FRAME: The picture, including subjects
that do not move dynamically, is output
in high resolution.
The default setting varies depending on the
country or region.
Depending on the DVD VIDEO, “4:3
LETTER BOX” may be selected automatically
instead of “4:3 PAN SCAN” or vice versa.
1)
2)
Continued

61GB
Setting the audio
options
 “AUDIO SETUP”
Configure audio related settings.
The default setting is underlined.
AUDIO DRC1) (Dynamic Range
Compression)
(DVD VIDEO only)
OFF: No compression of dynamic range.
STANDARD: Reproduces the sound
track with the kind of dynamic range that
the recording engineer intended. Useful
for watching movies at low volume late
at night.
MAX: Narrows the dynamic range fully.
TRACK SELECTION
(DVD VIDEO only)
Gives priority to the sound track which
contains the highest number of channels
when you play back a DVD VIDEO
on which multiple audio (PCM, DTS,
MPEG audio, or Dolby Digital) formats2)
are recorded.
OFF: No priority given.
AUTO3): Priority given.
“AUDIO DRC” can only be performed with
Dolby Digital sources.
2)
If each audio sound track has the same
number of channels, the system selects the
audio sound tracks in the order from PCM,
DTS, Dolby Digital, to MPEG.
3)
When you set “TRACK SELECTION”
to “AUTO,” the language may change.
The “TRACK SELECTION” setting has
higher priority than the “AUDIO” settings
in “LANGUAGE SETUP” (page 33, 59).
However, depending on the disc, this
function may not be performed.
1)
62GB
Setting the system
 “SYSTEM SETUP”
SCREEN SAVER
The screen saver will help prevent your
display device from becoming damaged
(ghosting). Press any button (e.g., ) to
cancel the screen saver.
ON: The screen saver image appears if
you do not operate the system for about
15 minutes.
OFF: The screen saver does not appear.
BACKGROUND
Selects the background color or picture
to be displayed on the TV screen. The
background color or picture is displayed
when playback is stopped or while
playing an AUDIO CD and MP3 files.
JACKET PICTURE: The jacket picture
(still picture) appears in the background,
but only when the jacket picture is
already recorded on the disc (DVD
VIDEO, CD-Extra, etc.). If the disc
does not contain a jacket picture, the
“GRAPHICS” picture appears.
GRAPHICS: A preset picture stored in
the system appears in the background.
BLUE: The background color is blue.
BLACK: The background color is black.
PARENTAL CONTROL
Sets the playback restrictions. For details,
see “Restricting playback of the disc
(PARENTAL CONTROL)” (page 56).
DivX
(MHC-GZR333i only)
Displays the registration code for this
system.
For more information, go to http://www.
divx.com on the Internet.
RESET*
Returns “SETUP” settings to the default
settings. For details, see “To return the
“SETUP” settings to the default settings*,
perform reset as follows:” (page 116).
* Except for “PARENTAL CONTROL” settings
CONNECTION
FRONT: YES
SUBWOOFER2):
YES: Select this if you have connected
the subwoofer.
NONE: Select this if the subwoofer is not
connected.
Disc
MULTI-DISC RESUME
(DVD VIDEO and VIDEO CD only)
ON: Stores the resume playback point in
the memory for up to 6 discs.
OFF: Does not store the resume playback
point in the memory. Playback starts at
the resume playback point only for the
current disc in the system.
Setting the speakers1)
 “SPEAKER SETUP”
LEVEL (FRONT)
L 0.0 dB3)
R 0.0 dB3)
SUBWOOFER 0.0 dB4)5)
To return to the default setting when
changing a setting, press CLEAR before you
press ENTER. However, note that you cannot
return the setting of “CONNECTION” to
default setting. Note that you cannot perform
“SPEAKER SETUP” when you connect
headphones or microphones to the unit.
2)
Depending on the settings of other speakers,
the subwoofer may output excessive sound.
3)
–6.0 dB (min) to 0.0 dB (max)
4)
–10.0 dB (min) to 0.0 dB (max)
5)
The items that are set to “NONE” in
“CONNECTION” cannot be selected.
1)
63GB
Tuner
Listening to the radio
You can listen to a radio station either by
selecting a preset station, or by manually
tuning in the station.
1 Press FUNCTION +/ (or press
TUNER/BAND on the unit)
repeatedly to select “FM” or “AM.”
2 Perform tuning.
For automatic scanning
Press and hold TUNING +/ until
the frequency indication changes and
then release.
Scanning stops automatically when
a station is tuned in and “TUNED”
appears on the TV screen. When
a FM stereo program is tuned in,
“STEREO” appears on the TV screen.
If “TUNED” does not appear and the
scanning does not stop, press  and
perform manual tuning.
64GB
For manual tuning:
Press TUNING +/ repeatedly.
For direct tuning:
Press D.TUNING, then use the
numeric buttons to enter the
frequency of the desired station. For
example, press 1, 0, 2, 5 and 0 to enter
the frequency of FM 102.50 MHz,
then press ENTER. If you cannot
tune in the station, make sure you
have entered the right frequency. If
you still cannot tune in the station,
the frequency is not used in your
area. To cancel direct tuning, press
D.TUNING.
Presetting a radio station
1 Tune in the desired station.
2 Press DVD/TUNER MENU.
“Memory?” flashes in the display.
3 Press ENTER or .
other stations.
You can preset up to 20 FM stations
and 10 AM stations.
To cancel presetting, press DVD/
TUNER MENU.
7 To call up a preset number, press
PRESET +/ repeatedly (or turn
OPERATION DIAL on the unit
clockwise or counterclockwise)
to select the desired preset
number.
Tuner
A preset number flashes in the
display.
The stations are stored from preset
number 1.
6 Repeat steps 1 to 6 to store
You can also press the numeric
buttons, then press ENTER to select a
preset station.
Tips
Preset number
4 Press  or  repeatedly (or press
the numeric buttons) to select
the desired preset number.
5 Press ENTER.
To improve broadcast reception, adjust the
supplied antennas, or connect an external
antenna.
When an FM stereo program has static noise,
press REPEAT/FM MODE repeatedly until
“MONO” appears in the display. There will
be no stereo effect, but the reception will
improve.
You can also set the frequency by viewing the
tuner information on the TV screen.
The station is stored.
65GB
iPod
Place an iPod into the iPod Dock on
the unit.
Playing the iPod
You can enjoy audio and video contents
stored in your iPod with this system.
See “Compatible iPod models with this
system” (page 128) for iPod models that
can be connected to this system.
You can select operating mode from the
following to operate your iPod connected
to this system.
iPod Display mode (page 67):
You can operate the iPod with buttons
on the connected iPod, in addition to
buttons on the unit and the remote.
In this mode, the iPod display can be
viewed on iPod itself.
Main Display mode (page 68):
You can view the iPod display on the
TV screen. In this mode, you cannot use
control buttons on the connected iPod.
To use the system as a battery charger
You can use the system as a battery
charger for the iPod when the system
is on.
The charging begins when the iPod is
placed on the iPod Dock. The charging
status appears in the iPod display. For
details, see the user’s guide of your iPod.
To stop charging the iPod
Remove the iPod. Turning off the system
also stops charging the iPod.
66GB
Notes
Using iPod Display mode
1 Press FUNCTION +/ repeatedly
to select the iPod function.
2 Press iPod/OPR on the unit to
select the operating mode until
“iPod DISPLAY MODE” appears.
Basic operations
To
Start playback
Pause playback
Scroll up/down
the iPod menus
Press
.
/.
/. You can scroll
up or down the iPod
menus much like the
Click Wheel operations
of the iPod or the drag
up-or-down operations
of the iPod touch.
Select a track
or chapter of
audiobook/
podcast
/. To fastforward or fast-rewind,
hold down the button.
Choose the
selected item
/ENTER. You can
choose the selected
item much like the
center button on the
iPod or the touch
operation of the iPod
touch.
Hold down /
during playback, and
release the button at
the desired point.
Find a point
in a track or
chapter of
audiobook/
podcast
Return to the
previous menu
or select a
menu
iPod
When placing or removing the iPod, handle
the iPod in the same angle as that of the iPod
connector on the unit and do not twist or
sway the iPod to prevent connector damage.
Do not carry the unit with an iPod set
on the connector. Doing so may cause a
malfunction.
When placing or removing the iPod, brace
the unit with one hand and take care not to
press the controls of the iPod by mistake.
Before disconnecting the iPod, pause
playback.
To change the volume level, use VOLUME
+/. The volume level does not change even
if adjusted on the iPod.
The iPod Dock on the unit is designed for
iPod only. You cannot connect any other
portable audio players.
To use an iPod, refer to the user’s guide of
your iPod.
Sony cannot accept responsibility in the event
that data recorded to iPod is lost or damaged
when using an iPod with this system.
/ DISPLAY/
RETURN. You can
return to the previous
menu or select a menu
much like the Menu
button on the iPod or
the touch operation of
the iPod touch.
Continued

67GB
Notes
Depending on the connected iPod,
operations may differ.
Before enjoying video, adjust the video
settings on the iPod to the appropriate
settings according to your situation.
It may take time to start playback depending
on the contents.
The volume cannot be adjusted using the
volume control on the iPod.
Hold down / to fast-forward (fastrewind) while playing video if / does
not function.
Because the operation of the system and the
iPod are different, you may not operate the
iPod using buttons on the remote or unit. In
this case, use control buttons on the iPod.
Using the Main Display mode
1 Press FUNCTION +/ repeatedly
to select the iPod function.
2 Press iPod/OPR on the unit
to select the operating mode
until “iPod DISPLAY MODE”
disappears.
Selected menu title
Current settings ( ,
Repeat,
Shuffle)
[Main Menu] list ([Music], [Videos],
[Settings])
Selected menu
68GB
To enjoy music and video while
browsing information on the TV screen
Example: Music playlists
1 Select [Music] from [Main
Menu], then press ENTER.
The [Music] menu display appears.
2 Select [Playlists] from [Music]
menu, then press ENTER.
The [Playlists] menu display appears.
press ENTER.
Files in the selected playlist appear.
4 Select the desired file, then
press ENTER.
Playback of the selected file starts.
Notes
In this mode, you cannot use control buttons
on the iPod.
When the system cannot display a character,
it is displayed as “_.”
Depending on the connected iPod, switching
to iPod Display mode (page 67) will be
necessary in order to display video/photo
images.
Before disconnecting the iPod, pause
playback.
While “Loading…” is displayed on the TV, do
not disconnect the iPod.
It may take time to start playback depending
on the contents.
Before enjoying video, adjust the video
settings on the iPod to the appropriate
settings according to your situation.
Depending on the connected iPod, some
video files may not be displayed on the
playlist.
Continued

iPod
3 Select the desired playlist, then
Current playing file
Artist name
Album name
Elapsed time
Currently playing file number/total
number of files
Playback status (Play, Pause, Fastforward, Fast-rewind)
69GB
Basic operations
To
Start playback
Pause playback
Scroll up/down
the iPod menus
Press
.
/.
/. You can scroll
up or down the iPod
menus much like the
Click Wheel operations
of the iPod or the drag
up-or-down operations
of the iPod touch.
Select a track
or chapter of
audiobook/
podcast
/. To fastforward or fast-rewind,
hold down the button.
Choose the
selected item
/ENTER. You can
choose the selected
item much like the
center button on the
iPod or the touch
operation of the iPod
touch.
Hold down /
during playback, and
release the button at
the desired point.
Find a point
in a track or
chapter of
audiobook/
podcast
Return to the
previous menu
or select a
menu
70GB
Notes
/ DISPLAY/
RETURN. You can
return to the previous
menu or select a menu
much like the Menu
button on the iPod or
the touch operation of
the iPod touch.
Depending on the connected iPod,
operations may differ.
It may take time to start playback depending
on the contents.
Settings menu
In the Settings menu, you can select
this unit’s settings: [Screen Saver],
[Color Theme], [Shuffle], [Repeat],
[Audiobooks]. The setting switches by
pressing ENTER or  repeatedly.
The default settings are underlined.
Note
[Screen Saver] and [Color Theme] can be
selected by pressing ENTER, and their settings
can be changed even when the iPod is not
placed into the unit.
Screen Saver
The screen saver image appears on the
TV after about 15 minutes of inactivity.
Press any button to cancel the screen
saver.
[ON]
[OFF]
Note
Turns on the screen
saver.
Turns off the screen
saver.
The display does not switch to the screen saver
image while playing video.
Color Theme
Selects the on screen display color on the
connected TV.
[Auto]
[White]
[Black]
[Green]
[Red]
[Blue]
The color is selected
automatically according
to your iPod.
The color is white.
The color is black.
The color is green.
The color is red.
The color is blue.
Plays the songs/albums in random order.
The setting is determined by the iPod
settings.
[OFF]
[Songs]
[Albums]
Does not play in
random order.
Plays songs in random
order.
Plays albums in
random order.
Plays songs repeatedly.
The setting is determined by the iPod
settings.
[OFF]
Does not play
repeatedly.
Repeat one song.
[Repeat to
One]
[Repeat to All] Repeat all songs.
Audiobooks
Changes the Audiobook playback speed.
The setting is determined by the iPod
settings.
[Slower]
[Normal]
[Faster]
iPod
Shuffle
Repeat
Plays Audiobook
slowly.
Plays Audiobook at
normal speed.
Plays Audiobook
rapidly.
Note
When video contents are played, the [Shuffle]
setting turns [OFF] automatically.
71GB
USB Device
Before using the USB
device with this system
See “Compatible devices with this
system” (page 126) for a list of USB
devices that can be connected to this
system.
Notes
When USB cable connection is necessary,
connect the USB cable supplied with the USB
device to be connected. See the operating
instructions supplied with the USB device
to be connected for details on the operation
method.
It may take about 10 seconds before
“Reading.” appears in the display depending
on the type of USB device connected.
Do not remove the USB device during
transfer, recording or erase operations. Doing
so may corrupt the data on the USB device or
damage the USB device itself.
Do not connect the system and the USB
device through a USB hub.
When the USB device is inserted, the system
reads all the files on the USB device. If there
are many folders or files on the USB device,
it may take a long time to finish reading the
USB device.
72GB
Always turn off the system before removing
the USB device. Removing the USB device
while the system is on may corrupt the data
on the USB device.
Compatibility with all encoding/writing
software cannot be guaranteed. If audio files
on the USB device were originally encoded
with incompatible software, those files may
produce noise or interrupted audio, or may
not play at all.
Note on the maximum number of
files and folders on a USB device
This system cannot transfer, record or playback
files and folders of the USB device in the
following cases.
When the number of files in a folder exceeds
150.
When the number of folders on a USB
device exceeds 200.
These numbers may vary depending on the file
structure and the folder structure. Do not save
other types of files or unnecessary folders on a
USB device that has audio files, video files or
JPEG image files.
Transferring music
from a disc to a USB
device
1 Connect the USB device to the
(USB) port.
Insert a USB device
Note
Do not use USB devices other than those
listed in “Compatible devices with this
system” (page 126). Operation of models
not listed is not guaranteed. Operation may
not always be ensured even when using a
compatible USB device.
Continued

USB Device
You can connect an optional USB device
to the
(USB) port on the unit and
transfer music from a disc to the USB
device.
You can transfer music only from an
AUDIO CD or DATA CD/DVD (MP3
files only).
The audio format of files transferred by
this system is MP3. When transferring
music from an AUDIO CD, the tracks
are transferred as 128 kbps MP3 files.
When transferring music from a DATA
CD/DVD, MP3 files are transferred with
the same bit rate as the original MP3 files.
The amount of free space required on the
USB device is about 1 MB per minute
when transferring music from an AUDIO
CD.
Required free space may be larger when
transferring music from a DATA CD/
DVD (MP3 files only).
You can easily transfer all the music on a
disc to a USB device (USB TRANSFER).
You can also transfer a single audio track
or file during playback (REC1).
73GB
2 Press FUNCTION +/ repeatedly
to select “DVD” (or press DVD on
the unit), then load the disc you
want to transfer.
If you have loaded the disc, press
DISC SKIP repeatedly (or DISC 1 
DISC 3 on the unit) to select the disc.
When the system automatically starts
playback, press  twice to cancel
resume playback.
3 Set the USB device to stand by
for transferring.
USB TRANSFER:
Press REC TO USB on the unit.
REC1:
Start playback of the track or MP3 file
you want to transfer, then press REC
TO USB on the unit.
The USB device stands by for
transferring.
4 Start transferring.
Press ENTER.
Transferring starts.
When the transfer is completed,
access to the USB device and the disc
player stops automatically.
To stop transferring
Press .
To remove the USB device
1 Press  to stop playback.
2 Press  to turn off the system.
3 Remove the USB device.
Using the on-screen display
You can also transfer music using the
on-screen display.
1 Press
DISPLAY when playback
is stopped.
The Control Menu appears on the TV
screen.
74GB
2 Press  or  repeatedly to select
(USB TRANSFER), then
press ENTER.
The options for “USB TRANSFER”
appear on the TV screen.
3 Press  or  repeatedly to select
the desired option, then press
ENTER.
4 Select the tracks you want to
transfer.
For AUDIO CD:
Press  or  repeatedly to select the
track, then press ENTER.
The tracks are marked in the order
that you select. To cancel the
selection, press ENTER again.
Remaining space of
the USB device
For AUDIO CD:
TRACK: The tracks on the AUDIO
CD appear. You can transfer the
desired track.
“Reading.” appears, and the tracks or
folders appear on the TV screen.
Note
It may take some time to display the tracks
or folders depending on the number of
tracks or folders.
Tracks to be transferred
To select all tracks on the AUDIO
CD
Press /// repeatedly to select
“ ALL,” then press ENTER. To
cancel the selection, select “ ALL,”
then press ENTER.
Continued

USB Device
For DATA CD/DVD:
TRACK: The folders on the DATA
CD/DVD appear. You can transfer
the desired MP3 file.
FOLDER: The folders on the DATA
CD/DVD appear. You can transfer
all MP3 files in the folder.
75GB
For DATA CD/DVD:
Press  or  repeatedly to select
the MP3 files or folders, then press
ENTER.
The MP3 files or folders are marked.
To cancel the selection, press ENTER
again.
Remaining space of
the USB device
To return to the previous display
Press  RETURN.
To erase audio files or folders from the
USB device
You can erase audio files or folders on the
USB device.
1 Connect the USB device to the
(USB) port.
2 Press FUNCTION +/ repeatedly
to select “USB” (or press USB on the
unit).
“FOLDER LIST” appears.
3 Press  or  repeatedly to select a
MP3 files or folders to be transferred
To select all tracks or folders on
the DATA CD/DVD
Press /// repeatedly to select
“ ALL,” then press ENTER. To
cancel the selection, select “ ALL,”
then press ENTER.
5 Press /// repeatedly to
select “START,” then press ENTER.
The system starts transferring and the
transfer status appears. No sound is
output during transfer.
To stop transferring, press .
76GB
folder.
To erase all audio files in a folder, press
CLEAR.
To erase an audio file, press ENTER.
“TRACK LIST” appears.
Press  or  repeatedly to select the
desired audio file, then press CLEAR.
4 Press  or  repeatedly to select
“YES.”
To cancel the erase operation, select
“NO.”
5 Press ENTER.
The selected audio file or folder is
erased.
Folder and file generation rules
When first transferring music to the
USB device, a “MUSIC” folder is created
directly below the “ROOT” folder.
Folders and files are generated within this
“MUSIC” folder as follows.
USB TRANSFER1)
Folder name
File name
MP3
Same as the music source2)
CD-DA
“FLDR001”3)
“TRACK001”3)
Music
source
Folder name
File name
MP3
“REC1-MP3”4) Same as the
music source2)
CD-DA
“REC1-CD”4)
REC1
“TRACK001”3)
Except when resuming playback.
Up to 64 characters of folder name and
60 characters of file name are assigned.
3)
Folder and file numbers are assigned serially
thereafter.
4)
A new file is created in the “REC1-MP3”
or “REC1-CD” folder each time REC1 is
performed.
1)
2)
When transferring music from a CD, the
tracks are transferred as 128 kbps MP3 files.
When transferring music from an MP3 disc,
MP3 files are transferred with the same bit
rate as the original MP3 files.
If you start transferring in shuffle play mode
or repeat play mode, the selected play mode
is automatically canceled and the play mode
switches to normal play mode.
CD text information is not transferred in the
created MP3 files.
If you cancel music being transferred
partway, an incomplete MP3 file, generated
on the USB device, will be deleted.
Transferring stops automatically if:
 you change the function.
 you turn off the system.
 the USB device runs out of space during
the transfer process.
 the number of files or folders on the USB
device reaches the limit for the number
that the system can recognize.
You cannot change the sound field when
transferring to the USB device.
If the folder to be erased contains nonMP3/WMA (Windows Media Audio)/AAC
(Advanced Audio Coding) audio files or sub
folders, these are not erased.
If a folder or audio file that you are trying
to transfer already exists on the USB device
with the same name, a sequential number is
added after the name without overwriting the
original folder or file.
USB Device
Music
source
Notes
77GB
Recording analog
audio to a USB device
You can record the sound from analog
audio sources. The sound is recorded as
128 kbps MP3 file.
1 Connect the USB device to the
(USB) port.
2 Press FUNCTION +/ repeatedly
to select the desired source.
TUNER FM/AM: To record from
this system’s tuner.
VIDEO/SAT: To record from the
optional component connected to
the VIDEO/SAT AUDIO IN L/R
jacks.
3 Press REC TO USB on the unit.
“Please Wait” appears and the display
cycles between “Free xx.x GB” (free
space on the USB device) and “Push
Enter.”
The USB device stands by for
recording.
78GB
4 Start playing the desired source
to record, then press ENTER.
To stop recording
Press .
To remove the USB device
1 Press  to stop recording.
2 Press  to turn off the system.
3 Remove the USB device.
To mark track numbers
You can mark the track numbers during
recording of any source.
Press REC TO USB on the unit at the
point you want to add a track mark.
The system pauses recording for a few
seconds and adds track mark, showing
message “New Track.” No sound is
recorded during pause time.
Note
The track numbers are automatically marked
when you record more than 60 minutes.
Folder and file generation rules
When first recording the analog audio
to the USB device, a “MUSIC” folder
is created directly below the “ROOT”
folder.
Folders and files are generated within this
“MUSIC” folder as follows.
Music
source
Folder name
File name
Tuner
“FM001”* or
“AM001”*
“TRACK001”*
VIDEO/
“VIDEO001”* “TRACK001”*
SAT
or “SAT001”*
AUDIO IN
L/R
Note
Recording stops automatically when:
you change the function.
you change the band.
you turn off the system.
the USB device runs out of space during the
recording.
the number of files or folders on the USB
device reaches the limit for the number that
the system can recognize.
See “Compatible devices with this
system” (page 126) for a list of USB
devices that can be connected to this
system.
You can listen to music stored in the USB
device.
The audio formats that can be played
back on this system are as follows: MP3*/
WMA*/AAC*
You can view image files and video files
stored in the USB device.
The image file and video file formats that
can be played back on this system are as
follows: JPEG/DivX/MP4*
DivX and MPEG4 video files can only be
played back on MHC-GZR333i.
* Files with DRM (Digital Rights
Management) copyright protection cannot
be played back on this system.
USB Device
* Folder and file numbers are assigned serially
thereafter.
Playing a file of the
USB device
1 Press FUNCTION +/ repeatedly
to select “USB” (or press USB on
the unit).
2 Connect the USB device to the
(USB) port.
Continued

79GB
3 Press
DISPLAY when playback
is stopped.
The Control Menu appears on the TV
screen.
4 Press  or  repeatedly to select
* (MEDIA), then press
ENTER.
The options for “MEDIA” appear on
the TV screen.
*
appears on LBT-LCD77Di.
MUSIC: for playing audio files
VIDEO1): for playing DivX video
files or MPEG4 video files
PHOTO: for playing JPEG image
files
6 Press  or  repeatedly to select
a folder.
Playing a folder:
Press  (or  on the unit).
The system starts playback from the
first file of the selected folder.
To stop playback, press .
Playing an audio file:
1 Press ENTER.
“TRACK LIST” appears.
MHC-GZR333i only.
1)
5 Press  or  repeatedly to select
the desired option, then press
ENTER. When the desired option
has already been selected, press
DVD/TUNER MENU.
A list of folders that contains the files
of the selected file type appears on the
TV screen.
80GB
2 Press  or  repeatedly to select
the desired audio file, then press
ENTER.
The system starts playback of the
selected audio file.
To stop playback, press .
Playing an image file:
1 Press PICTURE NAVI.
Thumbnail picture for the first
16 JPEG image files in the selected
folder is displayed.
Playing a video file (MHC-GZR333i
only):
1 Press ENTER.
“FILE LIST” appears.
2 Press  or  repeatedly to select
2 Press /// repeatedly to
select the image you want to
view, then press  (or  on
the unit).
The slide show starts from the
selected image file.
To stop playback, press .
The slide show stops when you
press  or .
the desired video file, then press
ENTER.
The system starts playing the
selected video files.
To stop playback, press .
Continued

USB Device
If there are more than 16 image
files in the selected folder, the scroll
bar appears at the right.
81GB
Other operations
To remove the USB device
To
Display
the next or
previous page
of “TRACK
LIST,”
“FOLDER
LIST” or “FILE
LIST”
Play back the
next folder of
audio files or
video files
1 Press  to stop playback.
Return to
“FOLDER
LIST” when
“TRACK LIST,”
or “FILE LIST”
is displayed.
Play back the
next folder of
JPEG image
files
Rotate the
image by 90
degrees
82GB
Do this
Press
or
repeatedly.
2 Press  to turn off the system.
3 Remove the USB device.
Notes
Press  repeatedly
until the last file of the
current folder, then
press  once. To
select the previous
folder, select the folder
from “FOLDER LIST.”
Press  RETURN.
Press  repeatedly
until the last file of the
current folder, then
press  once. To select
the previous folder,
select the folder from
“FOLDER LIST.”
Press  or  repeatedly
while viewing an
image. To return to
the original view, press
CLEAR.
The file formats that this system can play are
as follows:
 MP3: file extension “.mp3”
 WMA: file extension “.wma”
 AAC: file extension “.m4a”
 JPEG: file extension “.jpg” or “.jpeg”
 MP4: file extension “.mp4” or “.m4v”
 DivX: file extension “.avi” or “.divx”
Note that even when file names have the
above file extensions, if the actual files differ,
playing these files may generate a loud noise
which could damage the speaker system and
the system may malfunction.
The following USB devices/situations can
increase the time it takes to start playback:
 a USB device recorded with a complicated
tree structure.
 when the files in another folder have just
been played back.
 when you play back an AAC file.
The system can play back to a depth of
8 folders only.
Resume play back is canceled when you turn
off the system or change the function.
This system does not necessarily support all
the functions provided in a connected USB
device.
The playback order for the system may differ
from the order of the connected USB device.
Folders that have no MP3/WMA/AAC audio
files, DivX/MPEG4 video files (MHCGZR333i only) or JPEG image files are
skipped.
To specify the slide show speed
(JPEG image files only)
1 Press
DISPLAY repeatedly until the
Control Menu for JPEG image files
appears on the TV screen.
2 Press  or  repeatedly to select
(INTERVAL), then press ENTER.
The options for “INTERVAL” appear
on the TV screen.
3 Press  or  repeatedly to select the
4 Press ENTER.
The selected setting takes effect.
Note
Some JPEG image files (especially progressive
JPEG image files or JPEG image files with
3,000,000 pixels or more) may take a longer
time to display than others, which may make
the transitions seem longer than that of the
option you selected.
(JPEG image files only)
1 Press
DISPLAY repeatedly until the
Control Menu for JPEG image files
appears on the TV screen.
2 Press  or  repeatedly to select
(EFFECT), then press ENTER.
The options for “EFFECT” appear on
the TV screen.
3 Press  or  repeatedly to select the
desired setting.
The default setting is underlined.
MODE 1: The image sweeps in
from top to bottom of the screen.
MODE 2: The image sweeps in
from left to right of the screen.
MODE 3: The image stretches out
from the center of the screen.
MODE 4: The image randomly
cycles through the effects.
MODE 5: The next image slides
over the current image.
OFF: Turns off this function.
USB Device
desired transition interval.
The default setting is underlined.
NORMAL: Sets to the standard
duration.
FAST: Sets the duration shorter
than “NORMAL.”
SLOW 1: Sets the duration longer
than “NORMAL.”
SLOW 2: Sets the duration longer
than “SLOW 1.”
To select a transition effect for image
files in the slide show
4 Press ENTER.
The selected setting takes effect.
Continued

83GB
Playing in random order
(Shuffle Play)
You can play back the files on the USB
device in random order. Each time you
perform Shuffle Play, the playing order
may differ.
1 Press
DISPLAY.
The Control Menu appears on the TV
screen.
2 Press  or  repeatedly to select
(SHUFFLE), then press
ENTER.
The options for “SHUFFLE” appear
on the TV screen.
3 Press  or  repeatedly to select
the desired setting.
ON (MUSIC): all audio files in the
selected folder on the USB device
are played back randomly.
When no folder is selected, the first
folder is played back randomly.
4 Press ENTER.
Shuffle Play starts.
To cancel Shuffle Play, press CLEAR
or select “OFF” in step 3.
84GB
Notes
Shuffle Play is canceled when:
 you remove the USB device.
 you turn off the system.
 you change the function.
The same song may be played back
repeatedly for audio files.
Playing repeatedly (Repeat
Play)
You can play back audio files, video files
(MHC-GZR333i only), or JPEG image
files on the USB device repeatedly.
You can also repeat Shuffle Play.
1 Press
DISPLAY.
The Control Menu appears on the TV
screen.
2 Press  or  repeatedly to select
(REPEAT), then press
ENTER.
The options for “REPEAT” appear on
the TV screen.
3 Press  or  repeatedly to select
the desired setting.
MEMORY: repeats all the folders
on the USB device.
FOLDER: repeats the current
folder.
TRACK1): repeats the current file.
FILE2)3): repeats the current file.
Audio files only.
Video files only.
3)
MHC-GZR333i only.
1)
2)
When Shuffle Play is activated:
ON: repeats the Shuffle Play.
Repeat Play starts.
To cancel Repeat Play, press CLEAR
or select “OFF” in step 3.
Note
Repeat Play is canceled when:
 you remove the USB device.
 you turn off the system.
 you change the function.
When listening to music from a Sony
Ericsson mobile phone (W302 / W595 /
W760i / W890i / W902 / W910i) or
when transferring music from this
system to the mobile phone, you can
select the playback source or transferring
destination as follows:
internal memory of the mobile phone
Memory Stick
To select the playback source in the
“USB” function
Press MEMORY SELECT repeatedly.
You can select the internal memory or
Memory Stick of the mobile phone.
USB Device
4 Press ENTER.
5 Press  (or  on the unit).
Selecting the playback source
or transferring destination
on the Sony Ericsson mobile
phone
Selected memory number
Tip
You can also change the Repeat Play setting by
pressing REPEAT/FM MODE repeatedly.
Continued

85GB
To select the transferring destination
in the “DVD” function
1 Load a CD, DATA CD or DATA DVD.
2 Press MEMORY SELECT repeatedly.
You can select the internal memory or
Memory Stick of the mobile phone.
Notes
You cannot select the playback source or
transferring destination during playback or
transferring. Stop playback or transferring,
and then select the playback source or
transferring destination.
You can check the selected memory number
on the TV screen.
Selected memory number
You can select a Memory Stick when the
selected memory number is as follows:
Model name
W302
W595
W760i
W890i
W902
W910i
86GB
Memory number
#1
#2
#2
#2
#2
#2
If there is no Memory Stick inserted in the
mobile phone, you cannot select playback
source or the transferring destination.
Select a transferring destination before
transfer.
Sound Adjustment
Adjusting the sound
To
Reinforce the
sound
Select the
preset sound
effect
Do this
Press GROOVE on
the unit1). Each time
you press the button,
the display changes as
follows:
GROOVE ON2) 
Z-GROOVE ON2) 
GROOVE OFF 
GROOVE ON  …
Press PRESET EQ on
the unit repeatedly3).
Effect
ROCK
POP
JAZZ
DANCE
SOUL
TECHNO
HIP HOP
MOVIE
MP3 EQ
USER EQ 1,
2, 3
FLAT
Category
Standard music sources
Video files
MP3 files
User equalizer setting
(see “To adjust the
graphic equalizer and
store the user equalizer
setting” (page 88))
Original music source
(cancels the preset
effect)
2)
Continued

Sound Adjustment
The last selected setting appears when
GROOVE on the unit is pressed once.
The volume switches to power mode and the
equalizer curve changes.
3)
The last selected preset effect appears when
PRESET EQ on the unit is pressed once.
1)
Preset effect options
87GB
To adjust the graphic equalizer and
store the user equalizer setting
You can adjust the sound by raising or
lowering the level of specific frequency
band, then store up to three user
equalizer settings, in the memory.
1 Press EQ BAND/MEMORY on the
unit repeatedly to select a frequency
band or surround effect.
2 Press / to adjust the level or
select surround effect you want.
5 Press / to select a user
equalizer number (1 – 3) for the
equalizer setting (“MEMORY EQ-1”
through “MEMORY EQ-3”) you want
to store.
6 Press ENTER.
This setting is automatically stored as
the user equalizer setting you selected
in step 5.
The previous setting stored at this
memory location is erased and
replaced by the new setting.
Tip
If you do not want to store the setting, press
/ to select “EXIT?” and then press
ENTER.
Equalizer level
3 Repeat steps 1 and 2 to adjust the
level of other frequency bands and
surround effect.
4 Press ENTER.
“MEMORY EQ-1” appears in the
display.
88GB
Selecting the sound field
You can take advantage of the surround
sound simply by selecting one of the
sound fields. They bring the exciting and
powerful sound of movie theaters into
your home.
Press SOUND FIELD repeatedly.
The last selected sound field appears in
the display, and then you can select the
desired sound field.
When the headphones are not
connected:
VIRTUAL A*
Creates 3 sets of virtual surround
speakers from the sound of the front
speakers. This sound field is only effective
when you play back multi channel
sources.
VIRTUAL B*
Creates 1 set of virtual surround speakers
from the sound of the front speakers
without using actual surround speakers.
This mode is effective when the distance
between the front speakers is short. This
sound field is only effective when you
play back multi channel sources.
Continued

Sound Adjustment
2CH STEREO
Reproduces stereo output from multi
channel sources such as DVD VIDEOs
during “DVD” function. The system
outputs the original sound during
functions other than “DVD” and during
playback of stereo sources such as
AUDIO CD, VIDEO CD and MP3 files.
2CH SURR
Reproduces stereo output with surround
effect from multi channel sources such as
DVD VIDEO during “DVD” function.
The system outputs the original sound
with surround effect during functions
other than “DVD”.
89GB
When the headphones are connected:
HP 2CH
The normal sound field for headphones.
HP SURR
The sound field for headphones with
surround effect.
HP VIRTUAL*
The sound field for headphones with
virtual surround effect. This sound field
is only effective when you play back multi
channel sources.
* These sound fields cannot be selected when:
 the system is in stand by or during
transfer or recording.
 the Karaoke mode is turned on.
Notes
Depending on the disc, the surround effect
may not be as much as expected.
You cannot change the sound field when
transferring or recording to the USB device.
Singing along: Karaoke
You can enjoy Karaoke by setting the
system to Karaoke mode.
1 Press FUNCTION +/ repeatedly
to select “DVD” or “USB” (or press
DVD or USB on the unit).
2 Turn MIC LEVEL on the unit to
“MIN” to reduce the microphone
volume.
3 Connect a microphone to MIC
jack on the unit.
The Karaoke mode is turned on.
“KARAOKE MODE: ON” appears on
the TV screen.
4 Start playing the music and
adjust the volume.
DVD VIDEO, DVD-R/-RW in VR
mode, video files (MHC-GZR333i
only):
The system outputs the audio format
that you have selected.
AUDIO CD, VIDEO CD, MP3 files:
The audio setting automatically
changes to “1/L” and the system
outputs the left channel audio.
If you want to hear vocal:
Press AUDIO repeatedly to select
another audio channel.
90GB
5 Start singing along with
the music and adjust the
microphone volume by turning
MIC LEVEL.
To turn off the Karaoke mode
Disconnect the microphone or press
KARAOKE MODE. “KARAOKE MODE:
OFF” appears on the TV screen.
To adjust the microphone echo level
Turn ECHO LEVEL on the unit.
To cancel the echo effect, turn ECHO
LEVEL on the unit to “MIN.”
Notes
You can change the key to suit your vocal
range, except when the system is in stop
mode.
Press KEY CONTROL / to suit
your vocal range in Karaoke mode.
You can adjust the key higher or lower in
13 steps (6  6).
Notes
Depending on the disc, you may not be able
to change the key.
The key automatically returns to the original
key when:
 you turn off the system.
 you change the function.
 you change the disc.
 you open the disc tray.
 you stop playback.
 the title, track or audio file changes.
 you change the folder.
 the play item is changed during PBC
playback.
 you perform Lock Search.
 you cancel Karaoke mode.
 DVD layer is changed.
Continued

Sound Adjustment
The sound input from the microphone is not
output from the DVD DIGITAL OUT jack.
Karaoke mode is automatically turned off
when:
 you turn off the system.
 you change the function (except for the
“DVD” function or “USB” function).
 you connect the headphones.
 you disconnect the microphone.
If howling occurs:
 move the microphone away from the
speakers.
 change the direction of the microphone.
 lower the MIC LEVEL or ECHO LEVEL.
 press VOLUME  repeatedly (or
turn MASTER VOLUME on the unit
counterclockwise).
Changing the key (Key Control)
91GB
Playing Karaoke with any
stereo disc (“Karaoke Pon”)
You can enjoy Karaoke with a stereorecorded disc, even if it is a non-Karaoke
disc, by reducing the sound of the vocals.
Press KARAOKE PON in Karaoke
mode.
To cancel “Karaoke Pon” mode, press
KARAOKE PON again.
Notes
This function may not work well when:
 only a few instruments are playing.
 a duet is playing.
 the vocals on the disc deviate from the
center.
 playing monaural-recorded discs (the
accompaniment is also reduced).
 playing multiplex discs.
During “Karaoke Pon” mode, the stereo effect
is reduced.
“Karaoke Pon” mode is automatically
canceled when:
 you turn off the system.
 you change the function.
you change the disc.
 you open the disc tray.
 you press AUDIO.
 you set “VOCAL SELECT” to other than
“OFF.”
 you cancel Karaoke mode.
92GB
Selecting the vocals (Vocal
Select)
When playing a DVD with the “Dolby
Digital Karaoke” format in Karaoke
mode, you can turn on or off the guide
vocal recorded in the Karaoke track.
When playing a VIDEO CD or AUDIO
CD in Karaoke mode, you can listen to
the vocals.
You can also change the guide vocal
channel. You can select different kinds
of vocals.
1 Press
DISPLAY in Karaoke
mode.
The Control Menu appears on the TV
screen.
2 Press  or  repeatedly to select
(VOCAL SELECT), then
press ENTER.
The options for “VOCAL SELECT”
appear on the TV screen.
3 Press  or  repeatedly to select
the desired vocal channel.
The output channel changes as
follows.
The default setting is underlined.
When playing a DVD VIDEO
 OFF: Turns off the guide vocal.
 1+2: Guide vocal 1+2
 1: Guide vocal 1
 2: Guide vocal 2
When playing a VIDEO CD or
AUDIO CD
 OFF: Turns off the guide vocal.
 L+R: The same sound is output
from both speakers.
 STEREO: The standard stereo
sound
When playing a DVD VIDEO, the function
works only with the “Dolby Digital Karaoke”
format.
Depending on the disc, you may not be able
to change the guide vocal channel.
The channel returns to the default setting
when:
 you turn off the system.
 you change the function.
 you change the disc.
 you open the disc tray.
 you press AUDIO.
 you cancel Karaoke mode.
 you set “Karaoke S” mode to on.
When playing a DVD VIDEO recorded only
with one kind of guide vocal, select “1.”
Selecting the scoring mode
(Score Mode)
When Karaoke mode is turned on, you
can use the scoring mode.
Your score is calculated by comparing
your voice with the music source.
1 Press
DISPLAY in Karaoke
mode.
Sound Adjustment
When playing a Super VCD
 OFF: Turns off the guide vocal.
 1:L+R: The same sound of the
audio track 1 is output from both
speakers.
 1:STEREO: The stereo sound of the
audio track 1
 2:L+R: The same sound of the
audio track 2 is output from both
speakers.
 2:STEREO: The stereo sound of the
audio track 2
Notes
The Control Menu appears on the TV
screen.
4 Press ENTER.
Continued

93GB
2 Press  or  repeatedly to select
(SCORE MODE), then
press ENTER.
7 After singing for more than a
minute, press SCORE again to
view your score.
The options for “SCORE MODE”
appear on the TV screen.
Your score is calculated from a scale
of 0 to 99.
Your score is displayed for 5 seconds,
during which time the system enters
pause mode.
After your score, the ranking is
displayed as follows:
The ranking is displayed as a list
with top 3 scores.
Your score and ranking for the last
song flash.
If you are in the top 10, your
ranking is displayed. If not, “10+” is
displayed.
If your score is “0,” your score is not
displayed in the ranking list.
3 Press  or  repeatedly to select
a setting.
The default setting is underlined.
 BEGINNER 1: Beginner level. The
score updates every 3 seconds.
 BEGINNER 2: Beginner level.
 EXPERT 1: Advance level. The
score updates every 3 seconds.
 EXPERT 2: Advance level.
 DEMO: Demonstration mode.
The score is displayed regardless of
singing.
4 Press ENTER.
5 Start playing the music.
6 Press SCORE before singing a
song in Karaoke mode.
The previous highest score appears
on the TV screen and the display
changes as follows according to the
level selected for “SCORE MODE.”
: When you select “BEGINNER
1” or “EXPERT 1.”
: When you select “BEGINNER
2” or “EXPERT 2.”
: When you select “DEMO.”
94GB
Notes
The highest score is reset when the system is
turned off.
The “SCORE MODE” function may be
canceled when certain remote buttons are
pressed.
In some cases, you may not be able to use the
scoring mode.
Tip
The “SCORE MODE” setting is automatically
changed to “BEGINNER 1” when the system
is turned off.
Other Operations
Using the timers
The system offers three timer functions.
You cannot activate both the Play Timer
and the Rec Timer at the same time. If
you use either with the Sleep Timer, the
Sleep Timer has priority.
Use buttons on the remote to use the
timer functions.
Sleep Timer
You can fall asleep to music. This
function works even if the clock is not
set.
Press SLEEP repeatedly to select
the time you want.
The system turns off after the preset time.
Rec Timer
You can record from a preset radio
station at a specified time.
Make sure you have set the clock.
For Play Timer:
Prepare the sound source, and
then press VOLUME +/ (or turn
MASTER VOLUME on the unit) to
adjust the volume.
For Rec Timer:
Tune in the desired radio station or
call up the desired preset station.
2 Select the timer set mode.
Press TIMER MENU.
3 Press  or  repeatedly to select
“PLAY SET?” or “REC SET?,” then
press ENTER.
“ON” appears and the hour indication
flashes in the display.
4 Set the time to start playback or
recording.
Press  or  repeatedly to set the
hour, then press ENTER.
The minute indication flashes in the
display. Use the procedure above to
set the minute. “OFF” appears and the
hour indication flashes in the display.
5 Use the same procedure as in
step 4 to set the time to stop
playback or recording.
Continued

Other Operations
Play Timer
You can wake up to DVD, FM/AM
reception or optional USB device at a
preset time.
Make sure you have set the clock.
1 Prepare the sound source.
95GB
6 Select the sound source when
1 Press TIMER MENU.
For Play Timer:
Press  or  repeatedly until the
desired sound source appears, and
then press ENTER. The display shows
the timer settings.
2 Press ENTER.
For Rec Timer:
The display shows the timer settings.
When recording to a USB device,
press FUNCTION +/ repeatedly
to select “USB” (or press USB on the
unit), then connect the USB device to
the (USB) port.
7 Press  to turn off the system.
When you set the Rec Timer, the
system turns on 90 seconds before
the preset time. When you set the
Play Timer, the system turns on 30
seconds before the preset time.
If the system is on at the preset time,
the Play Timer and the Rec Timer will
not play. Do not operate the system
from the time the system turns on
until the playback or recording starts.
96GB
To check the setting
using Play Timer, or prepare
the USB device when using Rec
Timer.
“TIMER SELECT?” flashes in the
display.
3 Press  or  repeatedly to select
“PLAY SELECT?” or “REC SELECT?.”
4 Press ENTER.
To change the setting
Start over from step 1.
To cancel the timer
1 Press TIMER MENU.
“TIMER SELECT?” flashes in the
display.
2 Press ENTER.
3 Press  or  repeatedly to select
“TIMER OFF.”
4 Press ENTER.
Notes
The Play Timer and Rec Timer will not be
activated if the system is turned on or if
“STANDBY” flashes in the display. Be sure
to turn off the system at least 120 seconds
before the preset time.
The volume is reduced to minimum during
Rec Timer.
The track numbers are automatically marked
when you record more than 60 minutes.
Tips
The Play Timer setting remains as long as the
setting is not canceled manually.
The Rec Timer is canceled automatically after
the Rec Timer has been activated.
Changing the display
Turning off the display
 Power Saving Mode
The demonstration display and the clock
display can be turned off to minimize
the amount of power consumed during
standby mode (Power Saving Mode).
Press DISPLAY repeatedly while the
system is turned off.
Demonstration1) 
No display (Power Saving Mode) 
Clock2)  Demonstration  ...
1)
2)
The display changes and the indicators flash
even when the system is turned off.
The clock display automatically turns to
Power Saving Mode after 8 seconds.
You cannot perform the following operations
during Power Saving Mode:
 Setting the clock.
 Changing the AM tuning interval.
Continued

Other Operations
Note
97GB
Changing the power
illuminator
You can change the illumination pattern
around the MASTER VOLUME on the
unit.
1 Select the illumination setting.
Press OPTIONS on the unit
repeatedly until “ILLUMINATION”
appears in the display.
Press TIME/TEXT.
Each time you press TIME/TEXT while
playing the disc or USB device, the
display changes from     … 
…
The time display that you can view on the
TV screen depends on the media you are
playing.
T: title or track
C: chapter
D: disc
Bit rate
2 Press  or  to select the
desired illumination pattern,
then press ENTER.
Viewing information about
the disc and USB device in the
on-screen display
Press DISPLAY.
Each time you press DISPLAY, the
display (the front panel display only)
changes from       
…
 No display
 Clock display (for 8 seconds)
 Effect name (for 4 seconds)
98GB
Time information
Folder name
Track/file name
Note
The Control Menu display will show different
items depending on the media type.
When playing a DVD VIDEO or DVDR/-RW in VR mode:
Elapsed playing time of the current
title
Remaining time of the current title
Elapsed playing time of the current
chapter
Remaining time of the current chapter
Elapsed playing time of the current
title and disc title
When playing a VIDEO CD with PBC
function:
Elapsed playing time of the current
scene
Disc title
When playing an AUDIO CD or VIDEO
CD without PBC function:
Elapsed playing time of the current
track
Remaining time of the current track
Elapsed playing time of the disc
Remaining time of the disc
Elapsed playing time of the current
track and track name
When playing MP3 files or video files
on a DATA CD/DVD or USB device:
Elapsed playing time of the current file
and folder/file name*
Only alphabet letters, numbers and some
symbols can be displayed.
Depending on the media, the system can
only display a limited number of characters.
For MP3 files with format other than ISO
9660 Level 1 and Level 2, folder name and file
name may not be displayed.
Displaying the audio information of
the disc and USB device
(DVD VIDEO and video files only)
When you press AUDIO repeatedly
during playback, the format of the
current audio signal is displayed on the
TV screen.
When playing a DVD VIDEO:
For example, in Dolby Digital format,
multiple signals ranging from monaural
to 5.1 channel signals can be recorded on
a DVD VIDEO.
Example: For Dolby Digital 5.1 channel
2 Surround components
2 Front components +
1 Center component
1 LFE (Low Frequency
Effect) component
Continued

Other Operations
* If an MP3 file has the ID3 tag, the system will
display an album name or title name from
the ID3 tag information. The system supports
ID3 ver 1.0/1.1/2.2/2.3. ID3 ver 2.2/2.3 tag
information display has priority when both
ID3 ver 1.0/1.1 and ver 2.2/2.3 tags are used
for a single MP3 file.
Notes
99GB
When playing a video file:
Example: For MP3 format
Bit rate
Checking the date information of JPEG
image files
Hooking up optional
components
To enhance your system, you can connect
optional components. Refer to the
operating instructions provided with
each component.
Rear panel
When “Exif ”* tag is recorded in the
JPEG image files, you can check the date
information in the Control Menu by
pressing DISPLAY during playback.
Date information
* “Exchangeable Image File Format” is a
digital camera image format defined by
the “Japan Electronics & Information
Technology Industries Association” (JEITA).
Note
The date information format varies depending
on the area.
SUBWOOFER OUT jack
Connect the audio input jack of an
optional subwoofer.
Note
The effect may be limited or noise may
occur depending on the connected
subwoofer or the type of music being
played back.
100GB
VIDEO/SAT AUDIO IN L/R jacks
Connect the audio output jacks of an
optional component (such as VCR or
satellite tuner).
VIDEO/SAT VIDEO IN jack
Connect the video output jack of an
optional component (such as VCR or
satellite tuner).
COMPONENT VIDEO OUT jacks
Connect the component video input
jacks of the TV or projector. If your
TV accept progressive format signals,
you must use this connection and set
“PROGRESSIVE (COMPONENT
OUT)” to “ON” (page 29). You can
enjoy higher quality video images.
DVD DIGITAL OUT jack
Connect the digital optical input jack
of an optional digital component
(such as amplifier). You can enjoy
5.1 channel sound, if the connected
amplifier equipped with Dolby Digital
or DTS decoder.
Notes
Sound is output only when the system
function is set to “DVD” or “USB.”
If you press AUDIO, SOUND FIELD
or the buttons related to Karaoke
mode, or if you connect or disconnect
microphones or headphones, the sound
cuts off for a moment.
Notes
Other Operations
You cannot output the video signal from
the VIDEO/SAT VIDEO IN jack through
the COMPONENT VIDEO OUT jacks
of this unit.
You cannot output the video signal from
an iPod through the COMPONENT
VIDEO OUT jacks of this unit.
VIDEO OUT jack
Connect the video input jack of the
TV or projector.
Continued

101GB
Listening to a connected VCR or
satellite tuner
1 Press FUNCTION +/ repeatedly
(or press VIDEO/SAT on the unit)
to select “VIDEO” or “SAT.”
2 Start playing the connected
component.
To switch between the “VIDEO” and
“SAT” function
Hold down VIDEO/SAT on the unit and
press  on the unit while the system is
on. The system switches the function
from “VIDEO” to “SAT” or vice versa.
Note
If the sound is distorted or too loud when
“VIDEO” is selected, change the function to
“SAT.”
102GB
Enjoying the multi channel
sound with the optional
amplifier
1 Connect the digital optical cord.
See “Hooking up optional
components” (page 100).
2 Connect the speakers (not
supplied) to an optional
amplifier equipped with a
decoder.
For the speakers placement, refer to
the operating instructions supplied
with the connected amplifier.
3 Start playing a multi channel
source, such as a DVD VIDEO.
4 Select the desired audio format.
See “Changing the language/sound”
(page 40).
Additional Information
Troubleshooting
Should you encounter a problem with
your system, do the following:
1 Make sure the power cord and
speaker cords are connected
correctly and firmly.
2 Find your problem in the
troubleshooting checklist below and
take the indicated corrective action.
If the problem persists after doing all
of the above, consult your nearest Sony
dealer.
If the STANDBY indicator flashes
The display starts flashing as soon
as you plug in the power cord even
though you have not turned on the
system.
Press DISPLAY once while the system
is off. The demonstration disappears.
“– –:– –” appears in the display.
A power failure has occurred. Set the
clock (page 32) and timer settings
(page 95) again.
The system does not turn on.
Is the power cord plugged in?
The clock or timer setting is canceled.
The power cord is disconnected or a
power failure occurred. Redo “Setting
the clock” (page 32). If you have set
the timer, redo “Using the timers”
(page 95).
There is no sound.
Press VOLUME + repeatedly (or
turn MASTER VOLUME on the unit
clockwise).
The headphones are connected to the
PHONES jack.
Continued

Additional Information
Immediately unplug the power cord,
and check the following items.
Are you using only the supplied
speakers?
Are the + and  speaker cords
short-circuited?
Is anything blocking the ventilation
holes on the rear of the system?
After the STANDBY indicator stops
flashing, reconnect the power cord,
and turn on the system. If the issue
persists, contact your nearest Sony
dealer.
General
103GB
Check the speaker connections
(page 23).
There is no audio output during Rec
Timer.
The system is in pause mode, in Slowmotion Play or in Lock Search. Press
 (or  on the unit) to start the
playback.
No sound is output when transferring
music to the USB device.
There is no microphone sound.
Press VOLUME + repeatedly (or
turn MASTER VOLUME on the
unit clockwise) or turn MIC LEVEL
on the unit clockwise to adjust the
microphone volume.
Make sure the microphone is
connected to MIC jack correctly.
Make sure the microphone is turned
on.
There is severe hum or noise.
A TV or VCR is placed too close to the
unit. Move the unit away from the TV
or VCR.
Move the unit away from the source of
noise.
Connect the unit to a different wall
outlet.
Install a noise filter (commercially
available) to the power cord.
104GB
The timer does not function.
Check the timer setting and set the
correct time (page 96).
Cancel the Sleep Timer function.
The remote does not function.
Remove the obstacles between the
remote and the unit.
Move the remote closer to the unit.
Point the remote at the unit’s sensor.
Replace the batteries (R6/size AA).
Locate the unit away from the
fluorescent light.
There is acoustic feedback.
Reduce the volume.
Move the microphone away from the
speakers or change the direction of the
microphone.
The color irregularity on the TV
screen persists.
Turn off the TV set once, then turn it
on after 15 to 30 minutes. If the color
irregularity still persists, place the
speakers farther away from the TV set.
The sound from the component
connected to the VIDEO/SAT AUDIO
IN L/R jacks is distorted.
If “VIDEO” appears in the display
when you press VIDEO/SAT on the
unit, switch the display to “SAT” (see
“To switch between the “VIDEO” and
“SAT” function” (page 102)).
“THEATRE SYNC” function does not
work.
If distance between the TV and this
unit is too far, this function may not
work. Install the unit near the TV.
Speakers
Sound comes from one channel or
unbalanced left and right volume.
Place the speakers as symmetrically as
possible.
Check that the speakers are connected
securely and correctly.
The source being played back is
monaural.
The disc does not eject and “LOCKED”
appears in the display.
Consult your nearest Sony dealer or
local authorized Sony service facility.
The disc tray does not close.
Load the disc correctly.
Always close the disc tray by pressing
OPEN/CLOSE  on the unit. Do not
forcibly push the disc tray to close it as
this may cause a malfunction.
The system does not eject the disc.
You cannot eject the disc when
performing USB TRANSFER. Press
 to cancel the operation, then press
OPEN/CLOSE  on the unit to eject
the disc.
Consult your nearest Sony dealer.
Playback does not start.
Check whether a disc is loaded.
Wipe the disc clean (page 120).
Reload the disc.
Load the disc that this system can play
back (page 8, 36).
Load the disc on the disc tray with the
label side facing up.
Continued

Additional Information
Sound lacks bass.
Check that the speaker’s + and 
terminals are connected correctly.
Disc Player
105GB
Remove the disc and wipe away the
moisture on the disc, then leave the
system turned on for a few hours until
the moisture evaporates.
Press  (or  on the unit) to start
playback.
The region code on the DVD VIDEO
does not match the system.
Playback starts automatically.
The DVD VIDEO features an auto
playback function.
The sound skips.
Wipe the disc clean (page 120).
Reload the disc.
Move the unit to a place without
vibration (e.g., on top of a stable
stand).
Move the speakers away from the
unit, or place them on separate stands.
When you listen to a track or file
with bass sounds at high volume, the
speaker vibration may cause the sound
to skip.
You cannot perform some functions
such as Stop, Lock Search, Slowmotion Play, Repeat Play, Shuffle Play
or Program Play.
Depending on the disc, you may not
be able to do some of the operations
above. Refer to the operating
instructions supplied with the disc.
Playback does not start from the first
track.
Shuffle Play mode, Program Play mode
or Repeat Play mode is selected.
Resume playback has been selected.
Press  twice. Then, press  (or 
on the unit) to start playback.
The title of DVD VIDEO or PBC
menu automatically appears on the TV
screen.
106GB
Playback stops automatically.
Some discs may contain an auto pause
signal. While playing such a disc, the
playback stops at auto pause signal.
The MPEG4 video file does not have
the extension “.mp4” or “.m4v”.
The DivX video file does not have the
extension “.avi” or “.divx”.
DivX and MPEG4 video files cannot be
played back on LBT-LCD77Di.
The video file is larger than 720 (width)
× 576 (height) pixels.
If you cannot change the “MEDIA”
setting, re-load the disc or turn the
system off, then on.
The MP3 files take longer time to play
back than others.
After the system reads all the MP3 files
on the disc, playback may take more
time than usual if:
 the number of folders or MP3 files
on the disc is very large.
 the file structure is extremely
complex.
“Data error” appears on the TV
screen when playing a DATA CD/DVD.
The MP3 file/JPEG image file you want
to play is broken.
The MP3 file does not conform to
MPEG 1 Audio Layer 3.
The JPEG image file format does not
conform to DCF.
The JPEG image file has the extension
“.jpg” or “.jpeg”, but is not in JPEG
format.
The DivX video file has the extension
“.avi” or “.divx”, but is not in DivX
format.
Continued

Additional Information
The DATA CD/DVD (MP3 file/JPEG
image file/DivX video file/MPEG4
video file) cannot be played back.
The DATA CD is not recorded in a
format that conforms to ISO 9660
Level 1, Level 2, or Joliet (expansion
format).
The DATA DVD is not recorded
in a format that conforms to UDF
(Universal Disk Format).
The MP3 file does not have the
extension “.mp3”.
The data is not stored in the desired
format.
The audio file is not stored in MP3
(MPEG 1 Audio Layer 3) format.
The system can play back to a depth of
8 folders only.
The disc contains more than
200 folders.
The folder contains more than 150 files.
The JPEG image file does not have the
extension “.jpg” or “.jpeg”.
The JPEG image file is larger than
3,072 (width) × 2,048 (height) pixels in
normal mode, or more than 2,000,000
pixels in Progressive JPEG mode which
is mainly used on the Internet website.
For MP3 files and JPEG image files, the
DATA CD/DVD contains a video file.
107GB
The DivX video file does not conform
to a DivX Certified profile.
The MPEG4 video file has the
extension “.mp4” or “.m4v”, but does
not conform to MPEG4 Simple Profile.
The disc title, CD-TEXT and DVD-TEXT
characters do not appear properly.
The disc is recorded in format other
than ISO 9660 Level 1, Level 2 or Joliet
(expansion).
The character code that can be
displayed by this system are as follows:
 Upper cases (A to Z)
 Numbers (0 to 9)
 Symbols (< > * +, ? / [ ] \ _)
Other characters appear as “_.”
The surround effect is difficult to hear
when you are playing a Dolby Digital
or MPEG audio sound track.
Make sure the sound field is set
properly (page 89).
Check the speaker connection
(page 23).
Depending on the DVD VIDEO, the
output signal may not be the entire 5.1
channel. It may be monaural or stereo,
even if the sound track is recorded in
Dolby Digital or MPEG audio format.
The sound loses stereo effect when
you play back a DVD VIDEO, VIDEO
CD, AUDIO CD, MP3 file or video file.
Unplug the microphone or press
KARAOKE MODE repeatedly until
“KARAOKE MODE: OFF” appears in
the display.
108GB
Make sure the system is connected
properly.
Check the speaker connection
(page 23).
iPod
“Overload occurred. Turn off the
system and remove USB device.”
appears.
A problem has been detected with
the level of electrical current from the
iPod connector. Turn off the system
and remove the iPod from the iPod
connector. Make sure there is no
problem with the iPod. If this display
pattern persists, contact your nearest
Sony dealer.
There is no sound.
Make sure the iPod is connected
securely.
Make sure the iPod is updated with the
latest software. If not, update the iPod
before using with the system.
Make sure the iPod is playing music.
Adjust the volume.
It may take time to start playback
depending on the contents.
The sound is distorted.
Make sure the iPod is connected
securely.
Turn down the volume.
Set the “EQ” setting of the iPod to
“Off ” or “Flat.”
The iPod does not function.
Make sure the iPod is connected
securely.
Make sure the iPod is updated with the
latest software. If not, update the iPod
before using with the system.
Because the operation of the system
and the iPod are different, you may not
operate the iPod using buttons on the
remote or unit. In this case, use control
buttons on the iPod.
USB device
The iPod cannot be charged.
Make sure the iPod is connected
securely.
You can use the system as a battery
charger for iPod only when the system
is on.
Transferring or recording is stopped
before it is finished.
You are using an unsupported USB
device. See “Compatible devices
with this system” (page 126) for the
supported device types.
The USB device is not formatted
correctly. Refer to the operating
instructions supplied with the USB
device for how to format.
Turn off the system and remove the
USB device. If the USB device has a
power switch, turn the USB device
off and then on again after removing
it from the system. Then perform
transferring or recording again.
Video/photo image from the iPod
does not appear on the iPod display.
Make sure the iPod is connected
securely.
Adjust the video/photo image output
settings to the appropriate settings.
Additional Information
Video/photo image from the iPod
does not appear on the TV screen.
Make sure the iPod is connected
securely.
Set the operating mode to the iPod
Display mode to display photo images
(page 66).
Check that the TV output setting on
the iPod is on. (Refer to the user’s
guide of your iPod.)
Check that the iPod is compatible with
video output. (Refer to the user’s guide
of your iPod.)
You cannot start transferring or
recording to a USB device.
The following problems may have
occurred.
The USB device is full.
The number of files and folders on
the USB device has reached the
upper limit.
The USB device is write-protected.
On screen display does not appear on
the TV screen.
Make sure the iPod is connected
securely.
Check that the operating mode is set to
the Main Display mode (page 66).
Continued

109GB
If the transfer, recording and erase
operations are repeated multiple times,
the file structure within the USB device
becomes fragmented. Refer to the
operating instructions supplied with
the USB device for how to deal with
this problem. If the problem persists,
contact your nearest Sony dealer.
Transferring or recording results in
an error.
You are using an unsupported USB
device. See “Compatible devices
with this system” (page 126) for the
supported device types.
Turn off the system and remove the
USB device. If the USB device has a
power switch, turn the USB device
off and then on again after removing
it from the system. Then perform
transferring or recording again.
The USB device was disconnected
or the power was turned off during
the transfer or recording process.
Delete the partially-transferred file or
partially-recorded file, and perform
transferring or recording again. If this
does not fix the problem, the USB
device may be broken. Refer to the
operating instructions supplied with
the USB device for how to deal with
this problem. If the problem persists,
contact your nearest Sony dealer.
110GB
MP3 files or folders on the USB
device cannot be erased.
Check if the USB device is
write‑protected.
The USB device was disconnected
or the power was turned off during
the erase operation. Delete the
partially-erased file. If this does not
fix the problem, the USB device may
be broken. Refer to the operating
instructions supplied with the USB
device for how to deal with this
problem. If the problem persists,
contact your nearest Sony dealer.
Are you using a supported USB
device?
If you connect an unsupported USB
device, the following problems may
occur. See “Compatible devices
with this system” (page 126) for the
supported device types.
The USB device is not recognized.
File or folder names are not
displayed on this system.
Playback is not possible.
The sound skips.
There is noise.
A distorted sound is output.
Transferring or recording stops
before it is finished.
“OVER CURRENT” appears.
A problem has been detected with the
level of electrical current from the
(USB) port. Turn off the system and
remove the USB device from the
(USB) port. Make sure there is no
problem with the USB device. If this
display pattern persists, contact your
nearest Sony dealer.
There is no sound.
The USB device is not connected
correctly. Turn off the system and
reconnect the USB device, then turn
on the system and check if “USB
MEMORY” lights up.
The USB device cannot be connected
into the
(USB) port.
The USB device is being connected
backwards. Connect the USB device in
the correct orientation.
Erroneous display
Send the music data to the USB device
again, as the data stored in the USB
device may have been corrupted.
The character code that can be
displayed by this system are as follows:
 Upper cases (A to Z)
 Numbers (0 to 9)
 Symbols (< > * +, ? / [ ] \ _)
Other characters appear as “_.”
Continued

Additional Information
There is noise, skipping, or distorted
sound.
Turn off the system, then reconnect the
USB device.
The music data itself contains noise,
or the sound is distorted. Noise may
have entered during the transfer or
recording process. Delete the file, and
try transferring or recording again.
The bit rate used when encoding audio
files was low. Send audio files with
higher bit rate to the USB device.
“READING” is displayed for an
extended time, or it takes a long time
before playback starts.
The reading process can take a long
time in the following cases.
There are many folders or files on the
USB device.
The file structure is extremely
complex.
The memory capacity is excessive.
The file size is extremely large.
The internal memory is fragmented.
Thus, we recommend following these
guidelines.
Total folders on USB device: 200 or
less
Total files per folder: 150 or less
111GB
The USB device is not recognized.
Turn off the system and reconnect the
USB device, then turn on the system.
See “Compatible devices with this
system” (page 126) for the supported
device types.
The USB device does not work
properly. Refer to the operating
instructions supplied with the USB
device for how to deal with this
problem. If the problem persists,
contact your nearest Sony dealer.
“Data error” appears on the display
when playing a USB device.
The MP3 file/JPEG image file you want
to play is broken.
The JPEG image file format does not
conform to DCF.
The JPEG image file has the extension
“.jpg” or “.jpeg”, but is not in JPEG
format.
Play does not start.
Turn off the system and reconnect the
USB device, then turn on the system.
See “Compatible devices with this
system” (page 126) for the supported
device types.
Press  (or  on the unit) to start
playback.
Play does not start from the first
track.
Set the play mode to Normal Play
mode.
112GB
Files cannot be played back.
The MP3 file does not have the
extension “.mp3”.
The WMA file does not have the
extension “.wma”.
The AAC file does not have the
extension “.m4a”.
The DivX video file does not have the
extension “.avi” or “.divx”.
The MP4 file does not have the
extension “.mp4”.
The audio file is not stored in MP3/
WMA/AAC format.
The video file is not stored in MP4/
DivX format.
DivX and MPEG4 video files cannot be
played back on LBT-LCD77Di.
The JPEG image file does not have the
extension “.jpg” or “.jpeg”.
The JPEG image file is larger than
3,072 (width) × 2,048 (height) pixels in
normal mode, or more than 2,000,000
pixels in Progressive JPEG mode which
is mainly used on the Internet website.
Check the “MEDIA” setting (page 133).
USB device formatted with file systems
other than FAT12, FAT16 or FAT32 are
unsupported.*
The MP3 file is not stored in MP3
(MPEG 1 Audio Layer 3) format.
The WMA file stored in WMA DRM/
WMA Lossless/WMA PRO format
cannot be played back.
The AAC file stored in copyrightprotected AAC or AAC Lossless format
cannot be played back.
AAC files encoded at a sampling
frequency of 96 kHz cannot be played
back.
If you use a partitioned USB device,
only audio files on the first partition
can be played.
The system can play back to a depth of
8 folders only.
The number of folders has exceeded
200.
The number of files has exceeded 150.
Files that are encrypted or protected by
passwords, etc. cannot be played back.
* This system supports FAT12, FAT16 and
FAT32, but some USB devices may not
support all of these FAT. For details, see the
operating instructions of each USB device or
contact the manufacturer.
Picture
Continued

Additional Information
There is no picture.
The “VIDEO/SAT” function is
selected, but there is no input signal.
Check that the system is connected
securely.
The video cord is damaged. Replace it
with a new one.
Make sure you connect the unit to the
video input jack of your TV (page 101).
Make sure you turn on the TV and
operate the TV correctly.
Make sure you select the video input
on the TV so that you can view the
pictures from the system.
Make sure you set the color system
correctly, according to your TV’s color
system (Australian model only).
Make sure you connect the unit and
your TV using only the supplied video
cord.
Set “PROGRESSIVE (COMPONENT
OUT)” to “OFF” if you connect your
TV to the COMPONENT VIDEO
OUT jacks and your TV cannot accept
progressive signal.
You have set to progressive format
but your TV cannot accept the signal
in progressive format. In this case,
connect the VIDEO OUT jack to the
TV and set to the Interlace format
(page 27).
113GB
Even if your TV is compatible with
progressive format (525p/625p)
signals, the image may be affected
when you set to progressive format. In
this case, set to interlace format (the
default setting) (page 29).
Picture noise appears.
Wipe the disc clean (page 120).
If video signal from your system has to
go through your VCR to your TV, the
copy-protection applied to some DVD
VIDEO programs could affect the
picture quality.
When you play back a VIDEO CD
recorded in a different color system
from the one you set to the system,
the picture image may be distorted
(Australian model only) (page 61).
When you connect your TV to the
COMPONENT VIDEO OUT jacks
and play back video-based software
in progressive signal format, some
sections of the image may appear
unnatural due to the conversion
process.
Set the color system to match your TV
(Australian model only) (page 28).
The aspect ratio of the TV screen
cannot be changed even though
you can set “TV TYPE” under “VIDEO
SETUP” in the Setup Menu when you
play back a wide picture.
The aspect ratio is fixed on your DVD
VIDEO.
Depending on the TV, you may not
change the aspect ratio.
Messages do not appear on the TV
screen in your desired language.
Select the language for the on-screen
display in “OSD” under “LANGUAGE
SETUP” in the Setup Menu (page 33,
59).
The language for the sound track
cannot be changed.
Multilingual tracks are not recorded on
the DVD VIDEO being played back.
The DVD VIDEO prohibits changing
the language for the sound track.
The subtitles language cannot be
changed.
Multilingual subtitles are not recorded
on the DVD VIDEO being played
back.
The DVD VIDEO prohibits changing
the subtitles.
The subtitles cannot be turned off.
The DVD VIDEO prohibits turning off
subtitles.
114GB
The angles cannot be changed.
Multi-angles are not recorded on the
DVD VIDEO being played back.
The DVD VIDEO prohibits changing
the angles.
A stereo FM program cannot be
received in stereo.
Press REPEAT/FM MODE repeatedly
until “MONO” disappears from the
display.
Tuner
Optional components
The radio presetting is canceled.
The power cord is disconnected or a
power failure occurred for longer than
a day. Redo “Presetting a radio station”
(page 65).
There is no sound.
Refer to General item “There is no
sound.” (page 103) and check the
condition of the system.
Connect the component properly
(page 100) while checking:
 if the cords are connected properly.
 if the cord plugs are firmly inserted
all the way.
Turn on the connected component.
Refer to the operating instructions
supplied with the connected
component and start playback.
To change the AM tuning interval
The AM tuning interval is factory-preset
to 9 kHz (or 10 kHz for some areas).
Use buttons on the unit for the operation.
1 Press TUNER/BAND repeatedly to
select “AM.”
2 Press / to turn off the system.
Continued

Additional Information
There is severe hum or noise.
(“TUNED” or “STEREO” flashes in the
display.)
Set the proper band and frequency
(page 64).
Connect the antenna properly
(page 23).
Find a place and an orientation that
provide good reception, then set up
the antenna again. If you cannot obtain
good reception, we recommend that
you connect a commercially available
external antenna.
The supplied FM lead antenna receives
signals along its entire length, so make
sure you extend it fully.
Locate the antennas as far away from
the speaker cords and the power cord
as possible, to avoid picking up noise.
Try turning off the surrounding
electrical equipment.
115GB
3 Press DISPLAY repeatedly until “Sony
DEMO” appears in the display.
4 Press / while holding down
TUNING +.
“AM 9K STEP” or “AM 10K STEP”
appears in the display.
When you change the interval, all the
AM preset stations are erased.
If the system still does not operate
properly after performing the
above measures or other troubles
not described above occur, reset the
system as follows:
1 Press
DISPLAY when playback is
stopped.
The Control Menu appears on the TV
screen.
2 Press  or  repeatedly to select
(SETUP), then press ENTER.
3 Press  or  repeatedly to select
“CUSTOM,” then press ENTER.
The Setup Menu appears.
Use buttons on the unit to reset the
system to its factory default settings.
4 Press  or  repeatedly to select
1 Unplug the power cord.
5 Press  or  repeatedly to select
2 Plug the power cord back in.
3 Press  to turn on the system.
4 While holding down , press DISC 3
and press  at the same time.
“COLD RESET” appears in the display.
The system is reset to the factory
settings except for the “SETUP”
settings. You should set the settings
you made, such as the preset stations,
clock and timer.
116GB
To return the “SETUP” settings to the
default settings*, perform reset as
follows:
“SYSTEM SETUP,” then press ENTER.
“RESET,” then press ENTER.
6 Press  or  repeatedly to select
“YES,” then press ENTER.
It takes a few seconds to complete.
Do not press  when resetting the
system.
* Except for “PARENTAL CONTROL” settings
Self-diagnosis Function
(When letters/numbers appear in the
display)
When the self-diagnosis function
is activated to prevent the system
from malfunctioning, a 5-character
service number (e.g. C 13 50) with a
combination of a letter and 4 digits
appears on the TV screen or the front
panel display. In this case, check the
following table.
When you turn on the system, the
version number [VER.X.XX] (X is a
number) may appear on the TV screen.
Although this is not a malfunction and
for Sony service use only, normal system
operation will not be possible. Turn off
the system, and then turn on the system
again to operate.
Messages
Messages similar to the following, or
more detailed information, may appear
on the TV screen during operation.
CANNOT PLAY
A disc that cannot be played back was
inserted.
A DVD VIDEO with unsupported
region code was inserted.
Continued

Additional Information
First 3
Cause and corrective
characters of action
the service
number
C 13
This disc is dirty.
Clean the disc with a
soft cloth (page 120).
C 31
The disc is not inserted
correctly.
Restart the system,
then re-insert the
disc correctly.
E XX
To prevent a
(XX is a
malfunction, the
number)
system has performed
the self-diagnosis
function.
Contact your nearest
Sony dealer or local
authorized Sony
service facility and
give the 5-character
service number.
Example: E 61 10
When displaying the version number
on the TV screen
117GB
DATA ERROR
You tried to play a file on the USB device
that is not playable.
DATA ERROR (for DATA CD/DVDs)
The MP3 file, JPEG image file, DivX
video file and MPEG4 video file you
want to play back is damaged.
The MP3 file does not conform to
MPEG 1 Audio Layer 3 format.
The JPEG image file does not conform
to DCF format.
The MP3 file has the extension “.mp3”,
but is not in MP3 format.
The JPEG image file has the extension
“.jpg” or “.jpeg”, but is not in JPEG
format.
The DivX video file does not conform
to DivX Certified profiles.
The DivX video file has the extension
“.avi” or “.divx”, but is not in DivX
format.
The MPEG4 video file has the
extension “.mp4” or “.m4v”, but does
not conform to MPEG4 Simple Profile.
DEVICE ERROR
The USB device could not be recognized
or an unknown device is connected.
118GB
DEVICE FULL
The USB device is full.
DVD NO DISC
There is no disc on the disc tray.
ERASE ERROR
Erase of audio files or folders on the USB
device failed.
FATAL ERROR
The USB device has been disconnected
while transferring to the USB device.
FOLDER FULL
The number of folders on the USB device
has reached the maximum.
HUB NOT SUPPORTED
You have connected a USB hub to this
system.
INVALID
You have pressed an invalid button.
JPEG
A JPEG image file is being played back.
NO AUDIO
There is no audio file in the selected
folder.
NO DATA
There is no file or folder to play back.
NO USB DEVICE
No USB device is connected.
NOT IN USE
You have pressed a button whose
operation is not allowed or invalid at that
time.
NOT SUPPORT
An unsupported USB device is
connected.
OFF TIME NG!
The on time and off time of Play Timer or
Rec Timer is the same.
OVER CURRENT
An over current from the
was detected.
(USB) port
PASSWORD
“PARENTAL CONTROL” is set.
PLEASE WAIT
The system is doing initialization
process.
The system is readying for usage of a
USB device.
PROTECTED
The USB device is write-protected.
PUSH STOP
You have pressed the buttons whose
operation is only possible when playback
is stopped.
READING
The system is reading information
of the disc. Some buttons are not
available.
The system is recognizing the USB
device.
REC ERROR
Transferring did not start, stopped
partway, or otherwise could not be
performed.
Additional Information
TRACK FULL
The number of audio files on the USB
device has reached the maximum.
119GB
Precautions
Notes on discs
Before playing, wipe the disc with a
cleaning cloth from the center out to
the edge.
Do not clean discs with solvents, such
as benzine, thinner, or commercially
available cleaners or anti-static spray
intended for vinyl LPs.
Do not expose discs to direct sunlight
or heat sources such as hot air ducts,
nor leave it in a car parked in direct
sunlight.
Region code of DVD VIDEOs you can
play back on this system
Your system has a region code printed
on the back of the unit and will only
play back DVD VIDEOs labeled with
identical region code.
DVD VIDEOs labeled
will also be
played back on this system.
If you try to play back any other region
code DVD VIDEO, the message
“Playback prohibited by area limitations.”
will appear on the TV screen. Depending
on the DVD VIDEO, no region code
indication may be labeled even though
playing the DVD VIDEO is prohibited by
area restrictions.
120GB
Note on DualDiscs
A DualDisc is a two sided disc product
which mates DVD recorded material on
one side with digital audio material on
the other side. However, since the audio
material side does not conform to the
Compact Disc (CD) standard, playback
on this product is not guaranteed.
Notes on CD-R/-RW and DVD‑R/
-RW/+R/+RW
In some cases, CD-Rs/-RWs and
DVD-Rs/-RWs/+Rs/+RWs cannot be
played back on this system due to the
recording quality or physical condition
of the disc, or the characteristics of
the recording device and authoring
software. The disc will not be played
back if it has not been correctly
finalized. For more information, see
the operating instructions for the
recording device.
Note that some playback functions
may not work with some DVD+Rs/
+RWs, even if they have been correctly
finalized. In this case, view the disc by
normal playback.
A disc created in Packet Write format
cannot be played back.
Note on playback operations of DVD
VIDEOs and VIDEO CDs
Some playback operations of DVD
VIDEOs and VIDEO CDs may be
intentionally set by software producers.
Since this system play back DVD
VIDEOs and VIDEO CDs according to
the disc contents the software producers
designed, some playback features may
not be available. Also, refer to the
instructions supplied with the DVD
VIDEOs or VIDEO CDs.
Music discs encoded with copyright
protection technologies
This product is designed to play back
discs that conform to the Compact Disc
(CD) standard. Recently, various music
discs encoded with copyright protection
technologies are marketed by some
record companies. Please be aware that
among those discs, there are some that
do not conform to the CD standard and
may not be playable by this product.
On cleaning discs, disc/lens cleaner
Do not use a commercially available
cleaning disc or disc/lens cleaner (wet or
spray type). These may cause apparatus to
malfunction.
On operating voltage
Before operating the system, check
that the operating voltage of the unit is
identical with the voltage of your local
power supply.
On safety
Completely disconnect the power
cord (mains lead) from the wall outlet
(mains) if it is not going to be used
for an extended period of time. When
unplugging the unit, always grip the
plug. Never pull the cord itself.
Should any solid object or liquid get
into the system, unplug the system, and
have it checked by qualified personnel
before operating it again.
Continued

Additional Information
Notes on Multi Session disc
If the first session is recorded in
AUDIO CD or VIDEO CD format,
only the first session will be played
back.
The system will recognize a Multi
Session disc as an AUDIO CD if there
is a session recorded in AUDIO CD
format on the disc. However, the
system will only play back the disc if
the first session is recorded in AUDIO
CD format.
This system can play back Multi
Session discs when an MP3 file, a
JPEG image file, a DivX video file or
an MPEG4 video file is contained in
the first session. Any subsequent MP3
files, JPEG image files, DivX video files
or MPEG4 video files recorded in later
sessions can also be played back.
Note on copyright-protected content
The transferred music is limited to
private use only. Use of the music beyond
this limit requires permission of the
copyright holders.
121GB
On placement
Do not place the system in an inclined
position or in locations that are
extremely hot, cold, dusty, dirty, or
humid or lacking adequate ventilation,
or subject to vibration, direct sunlight
or a bright light.
Be careful when placing the unit
or speakers on surfaces that have
been specially treated (for example,
with wax, oil, polish) as staining or
discoloration of the surface may result.
If the system is brought directly
from a cold to a warm location or is
placed in a very damp room, moisture
may condense on the lens inside the
DVD player, and cause the system to
malfunction. In this situation, remove
the disc, and leave the system turned
on for about an hour until the moisture
evaporates.
On heat buildup
Heat buildup on the unit during
operation is normal and is not cause
for alarm.
Do not touch the cabinet if it has been
used continuously at a high volume
because the cabinet may have become
hot.
Do not obstruct the ventilation holes.
122GB
In case color irregularity is observed
on a nearby TV screen
With the magnetically shielded type of
speakers, the speakers can be installed
near a TV set. However, color irregularity
may still be observed on the TV screen
depending on the type of your TV set. In
this situation, turn off the TV, wait 15 to
30 minutes, and turn it back on. If there
is no improvement, move the speakers far
away from the TV.
IMPORTANT NOTICE
Caution: If you leave a still video
image or on-screen display image
displayed on your TV for an
extended period of time via this
system, you risk permanent damage
to your TV screen. Projection TVs
are especially susceptible to this.
Cleaning the cabinet
Clean this system with a soft cloth
slightly moistened with a mild detergent
solution. Do not use any type of abrasive
pad, scouring powder, or solvent, such as
thinner, benzine, or alcohol.
Specifications
Main unit
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
(North American model only)
With 6 ohm loads, both channels driven,
from 120  10,000 Hz; rated 85 watts per
channel minimum RMS power, with no
more than 1% total harmonic distortion
from 800 milliwatts to rated output.
Amplifier section
North American model:
RMS output power (reference):
210 W + 210 W (per channel at 6 Ω,
1 kHz)
Other models:
The following measured at AC 240 V,
50/60 Hz
Power output (rated):
105 W + 105 W (at 6 Ω, 1 kHz, 1%
THD)
RMS output power (reference):
210 W + 210 W (per channel at 6 Ω,
1 kHz)
Inputs
VIDEO/SAT VIDEO IN (phono jack):
1 Vp-p, 75 Ω
VIDEO/SAT AUDIO IN L/R (phono jacks):
voltage 250/450 mV, impedance
47 kΩ
MIC (phone jack):
sensitivity 1 mV, impedance 10 kΩ
Outputs
Continued

Additional Information
VIDEO OUT (phono jack):
max. output level 1 Vp-p, unbalanced,
Sync negative, load impedance 75 Ω
COMPONENT VIDEO OUT
Y: 1 Vp-p, 75 Ω
Pb: 0.7 Vp-p, 75 Ω
Pr: 0.7 Vp-p, 75 Ω
DVD DIGITAL OUT (Square optical
connector jack, rear panel):
Wavelength 650 nm
PHONES (stereo mini jack):
accepts headphones of 8 Ω or more
SUBWOOFER OUT:
Voltage 1 V, impedance 1 kΩ
SPEAKERS
MHC-GZR333i:
Use only the supplied speaker
SS‑GZR777D.
LBT-LCD77Di:
Use only the supplied speaker
SS‑LCD77DI.
(USB) port: Type A
Maximum current:
500 mA
123GB
Disc player section
System:
Compact disc and digital audio and
video system
Laser Diode Properties
Emission Duration: Continuous
Laser Output*: Less than 44.6µW
*This output is the value measurement
at a distance of 200mm from the
objective lens surface on the Optical
Pick-up Block with 7mm aperture.
Frequency response
DVD (PCM 48 kHz): 2 Hz  22 kHz
(±1 dB)
CD: 2 Hz  20 kHz (±0.5 dB)
Video color system format
North American model: NTSC
Other models: NTSC and PAL
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
North American model:
87.5 MHz  108.0 MHz (100 kHz
step)
Other models:
87.5 MHz  108.0 MHz (50 kHz step)
Antenna:
FM lead antenna
Antenna terminals:
75 Ω unbalanced
Intermediate frequency:
10.7 MHz
124GB
AM tuner section
Tuning range
Australian model:
531 kHz  1,710 kHz (9 kHz step)
530 kHz  1,710 kHz (10 kHz step)
Other models:
530 kHz  1,710 kHz (10 kHz step)
531 kHz  1,710 kHz (9 kHz step)
Antenna:
AM loop antenna
Antenna terminals:
External antenna terminal
Intermediate frequency:
450 kHz
Speaker
Front speaker (SS-GZR777D) for
MHC-GZR333i
Front speaker (SS-LCD77DI) for LBTLCD77Di
Speaker system:
3-way, Bass reflex, Magnetically
shielded
Speaker unit
Woofer: 180 mm, cone type
Tweeter: 50 mm, horn type
Super Tweeter: 40 mm, horn type
Rated impedance: 6 Ω
Dimensions (W/H/D):
Approx. 255 mm × 350 mm ×
255 mm
Mass:
Approx. 5.2 kg
General
Power requirements
North American model:
AC 120 V, 60 Hz
Australian model:
AC 230 V  240 V, 50/60 Hz
Mexican model:
AC 127 V, 60 Hz
Other models:
AC 120 V, 220 V, 230 V  240 V,
50/60 Hz, adjustable with voltage
selector
Power consumption:
150 W
Dimensions (W/H/D) (excl. speakers):
Approx. 280 mm × 325 mm ×
430 mm
Mass (excl. speakers):
Approx. 11.2 kg
Supplied accessories:
Remote Commander (1)
AM loop antenna (1)
FM lead antenna (1)
Video cord (1)
Speaker pads (8)
R6 (Size AA) batteries (2)
Supported file format
MP3 (MPEG 1 Audio Layer-3)
File extension: .mp3
Bitrate: 32 kbps  320 kbps, VBR
Sampling frequencies: 32/44.1/48 kHz
DRM: Not compatible
WMA
File extension: .wma
Bitrate: 48 kbps  192 kbps
Sampling frequencies: 44.1 kHz
DRM: Not compatible
AAC
File extension: .m4a
Bitrate: 48 kbps  320 kbps
Sampling frequencies: 44.1 kHz
DRM: Not compatible
DivX
File extension: .avi/.divx
Video codec: DivX video
Bitrate: 8 Mbps (MAX)
Frame rate: 30 fps
Resolution: 720 × 576 pixels
Audio codec: MP3
Additional Information
Continued

125GB
MPEG4
File format: MP4 File Format
File extension: .mp4/.m4v
Video codec:
MPEG4 Simple Profile
(AVC is not compatible.)
Bitrate: 4 Mbps
Frame rate: 30 fps
Resolution: 720 × 576 pixels
Audio codec:
AAC-LC
(HE-AAC is not compatible.)
DRM: Not compatible
Design and specifications are subject to
change without notice.
Standby power consumption: 0.5 W
Halogenated flame retardants are not used
in the certain printed wiring boards.
126GB
Compatible devices
with this system
You can use the following devices on this
system.
Verified Sony USB devices
Product name Model name
NWD-B103 / B105 /
Walkman
B103F / B105F
NWD-E023F / E025F
NWZ-A815 / A816 /
A816B / A818
NWZ-A726 / A726B /
A728 / A728B / A729 /
A826 / A828 / A829
NWZ-B133 / B135 /
B133F / B135F
NWZ-E435F / E436F /
E438F
NWZ-S515 / S516 /
S615F / S616F /
S618F / S715F /
S716F / S718F
NWZ-S636F / S638F /
S639F / S736F /
S738F / S739F
IC Recorder
ICD-UX71 / UX81 /
UX91
ICD-SX700 / SX800 /
SX900
MICROVAULT USM512JX / 1GJX /
2GJX / 4GJX
USM512JX / 1GJX /
2GJX / 4GJX
USM1GL / 2GL /
4GL / 8GL / 16GL
USM1GLX / 2GLX /
4GLX / 8GLX / 16GLX
®
Verified Sony Ericsson mobile phone
Notes on using the Sony Ericsson
mobile phone
Product name Model name
W302 / W350i /
Walkman
W380i / W580i /
phone
W595 / W660i /
W710i / W760i /
W850i / W880i /
W890i / W902 /
W910i / W960i /
W980
Connect to this system with the power of the
mobile phone on.
When connecting to this system, set the data
transfer mode of your mobile phone to File
Transfer (Mass Storage). For details, refer
to the operation manual supplied with the
mobile phone.
Use the USB cable supplied with the mobile
phone when connecting to this system.
While the mobile phone is connected to this
system, do not insert or remove the memory
card.
Some files supported by the mobile phone are
not supported by this system.
In the case that the song which is registered
as the playlist in the mobile phone is erased
by this system, the playlist registration is not
deleted.
The Play Timer and Rec Timer in this system
are not supported.
®
Notes
When formatting the USB device, be sure
to format using the device itself or the
dedicated formatting software for that device.
Otherwise, you may be unable to transfer
music to the USB device properly on this
system.
Do not use USB devices other than these
USB devices. Operation of models not listed
here is not guaranteed.
Operation may not always be ensured even
when using these USB devices.
Some of these USB devices may not be
available for purchase in certain areas.
®
Notes on Walkman
®
Some files supported by the Walkman are
not supported by this system.
When transferring music to a Walkman
using “Media Manager for WALKMAN,” be
sure to transfer in MP3 format.
When connecting a Walkman to the
system, be sure to connect after the display
“Creating Library” or “Creating Database” on
the Walkman has disappeared.
®
Additional Information
®
®
127GB
Compatible iPod models with this system
You can use the following iPod models on this system. Update your iPod with the latest
software before using it.
128GB
iPod nano
5th generation
(video camera)
iPod touch
2nd generation
iPod classic
120 GB
160 GB (2009)
iPod nano
4th generation
(video)
iPod classic
160 GB (2007)
iPod touch
1st generation
iPod nano
3rd generation
(video)
iPod classic
80 GB
iPod nano
2nd generation
(aluminum)
iPod
5th generation
(video)
iPod nano
1st generation
iPod
4th generation
(color display)
iPod
4th generation
iPod mini
Guide to the Control Menu display
Use the Control Menu to select a function and to view related information. Press
DISPLAY repeatedly to turn on, turn off or change the Control Menu display as
follows:
Control Menu display 1  Control Menu display 2*  Control Menu display off 
Control Menu display 1  …
* Control Menu display 2 appears when available.
Control Menu display
The Control Menu display 1 and 2 will show different items depending on the disc type.
Example: Control Menu display 1 when playing a DVD VIDEO
Currently playing title number
Currently playing chapter number
Total number of titles
Control Menu
items
Playback status ( Playback,
 Pause,  Stop, etc.)
Type of disc being
played back
Elapsed playing time
Current setting
Function name of
selected Control
Menu item
Options
Additional Information
Selected item
Total number of chapters
Operation message
To turn off the Control Menu
Press
DISPLAY repeatedly until the Control Menu disappears from the TV screen.
Continued

129GB
List of Control Menu items
Item
Item Name, Function, Relevant Disc Type
[TITLE] (page 43)/[SCENE]/[TRACK] (page 43)
Selects the title, scene or track to be played back.
[CHAPTER]/[INDEX] (page 43)
Selects the chapter or index to be played back.
[TRACK]1) (page 43)
Selects the track or audio file to be played back.
[ORIGINAL/PLAY LIST] (page 42)
Selects the playback sequence either to the originally recorded
sequence or to the playlist created on the disc.
[TIME]1) (page 44)
Checks the elapsed playing time and the remaining time.
You can play from a desired point by inputting the time code (DVD
VIDEO/DVD-VR only).
[PROGRAM] (page 50)
Plays back the tracks in the order you want.
[SHUFFLE]1) (page 52, 84)
Plays back the tracks or audio files in random order.
130GB
Item
Item Name, Function, Relevant Disc Type
[REPEAT]1) (page 53, 84)
Plays back all discs repeatedly, the entire disc (all titles/all tracks/all
files/all folders) repeatedly or one title/chapter/track/folder/file
repeatedly.
[A/V SYNC] (page 55)
You can adjust the delay between the picture and sound.
[SETUP]1) (page 33, 58)
QUICK
Use “QUICK” Setup to choose the language of the on-screen display
and the aspect ratio of the TV screen.
CUSTOM
In addition to the “QUICK” setup setting, you can adjust other
settings.
[FOLDER]1) (page 54, 75)
Selects the folder to be played back.
[DATE]1) (page 100)
Displays the date when the picture was taken by a digital camera.
[INTERVAL]1) (page 49, 83)
Specifies the duration for which the slides are displayed on the TV
screen.
Continued

Additional Information
[FILE]1) (page 54)
Selects the JPEG image file or video file to be played back.
131GB
Item
Item Name, Function, Relevant Disc Type
[EFFECT]1) (page 49, 83)
Selects the transition effects to be used for changing slides during a
slide show.
[MEDIA]1) (page 44, 48, 50, 80)
:
LBT-LCD77Di Selects the data type (audio file, JPEG image file, video file, or both
MP3 file and JPEG image file) to be played back.
:
MHC-GZR333i
[USB TRANSFER] (page 75)
Transfers music on an AUDIO CD or DATA CD/DVD to a USB
device.
[KARAOKE MODE]1) (page 90)
Sets Karaoke mode to on or off.
[VOCAL SELECT]2) (page 92)
Selects the guide vocal recorded on the “Dolby Digital Karaoke”
Format disc (DVD VIDEO only).
Selects the vocal type recorded on the disc (VIDEO CD, AUDIO CD
only).
Turns off the vocal.
[SCORE MODE]1)2) (page 93)
Calculates your vocal score by comparing your voice with the music
source.
These functions are the same when using a USB device. However, some menu items
may not be available.
2)
This function is only available during Karaoke mode.
1)
132GB
Playback priority of file types
The table below describes the playback priority of file types under the “MEDIA” setting.
File type on
a disc or USB
device
“MEDIA” setting
VIDEO1)
Disc
USB
device
MUSIC/
PHOTO
MUSIC
PHOTO
Disc
Disc/USB
device
Disc/USB
device
Video files1) only
Video files1) Video files1) Video files1) Video files1) Video files1)
JPEG image files
only
JPEG image JPEG image JPEG image JPEG image JPEG image
files
files
files
files
files
Audio files only
MP3 files
Video files1) and
JPEG image files
Video files1) Video files1) JPEG image Video files1) JPEG image
files
files
Video files1) and
audio files
Video files1) Video files1) MP3 files
Audio files2) Audio files2)
Audio files and
JPEG image files
MP3 files
and JPEG
image files
with slide
show
MP3 files
and JPEG
image files
with slide
show
Audio files2) JPEG image
files
Video files1),
audio files, and
JPEG image files
Video files1) Video files1) MP3 files
and JPEG
image files
with slide
show
Audio files2) JPEG image
files
Audio files
Audio files
2)
Audio files2) Audio files2)
Additional Information
These are only available on MHC-GZR333i.
When using a disc, you can play MP3 files only.
1)
MP3 files
133GB
Language code list
The language spellings conform to the ISO 639:1988 (E/F) standard.
134GB
Parental Control area code list
Additional Information
135GB
Glossary
Auto Pause
An automatic pause according to the
signal encoded on the disc while playing
a VIDEO CD. If the CD/DVD player
does not resume playback for a long time,
perform resume playback manually.
Chapter
Subdivision of a title on a DVD VIDEO.
A title is composed of several chapters.
DivX®
Digital video technology created by
DivX, Inc. Videos encoded with DivX
technology are among the highest quality
with a relatively small file size.
Dolby Digital
This movie theater sound format is
more advanced than Dolby Surround
Pro Logic. In this format, the surround
speakers output stereo sound with
an expanded frequency range and a
subwoofer channel for deep bass is
independently provided. This format is
also called “5.1” because the subwoofer
channel is counted as 0.1 channel (since
it functions only when a deep bass effect
is needed). All six channels in this format
are recorded separately for superior
channel separation. Furthermore, since
all the signals are processed digitally, less
signal degradation occurs.
136GB
“Dolby Digital Karaoke” format
(DVD VIDEO only)
The Dolby Digital format, which
reproduces surround sound using
5 channels, can also contain the
“Dolby Digital Karaoke” format
which is specialized for Karaoke. In
the “Dolby Digital Karaoke” format
discs, guide melody and guide vocal
tracks are recorded in addition to the
accompaniment. You can select guide
vocal when Karaoke mode is turned on.
DTS
Digital audio compression technology
developed by DTS, Inc. This technology
conforms to 2-channel surround. The
surround channel is stereo and there
is discrete subwoofer channel in this
format. DTS provides the same 2 discrete
channels of high quality digital audio.
The good channel separation is realized
because the all channel data is recorded
discrete and processed in digital.
DVD VIDEO
DVD-RW
A DVD-RW is a recordable and
rewritable disc that is the same size as
a DVD VIDEO. The DVD-RW has two
different modes: VR mode and Video
mode. DVD-RWs created in Video
mode have the same format as a DVD
VIDEO, while discs created in VR (Video
Recording) mode allow the contents to
be programmed or edited.
DVD+RW
A DVD+RW (plus RW) is a recordable
and rewritable disc. DVD+RWs use a
recording format that is comparable to
the DVD VIDEO format.
File
Audio file (MP3/WMA/AAC), JPEG
image file, DivX* and MPEG4* video file
recorded on a DATA CD, DATA DVD
or USB device. (“File” is an exclusive
definition for this system.)
Film based software, Video based
software
DVD VIDEOs can be classified as Film
based or Video based software. Film
based DVD VIDEOs contain the same
images (24 frames per second) that are
shown at movie theaters. Video based
DVD VIDEOs, such as television dramas
or sitcoms, display images at 30 frames
(or 60 fields) per second.
Folder
Section of a music or picture piece on a
DATA CD, DATA DVD or USB device
containing MP3 files, JPEG image files,
DivX* and MPEG4* video files.
Continued

Additional Information
A disc that contains up to 8 hours of
moving pictures even though its diameter
is the same as an AUDIO CD. The data
capacity of a single-layer and singlesided DVD VIDEO, at 4.7 GB (Giga
Byte), is 7 times that of an AUDIO CD.
Furthermore, the data capacity of a duallayer and single-sided DVD VIDEO is
8.5 GB, a single-layer and double-sided
DVD VIDEO 9.4 GB, and a dual-layer
and double-sided DVD VIDEO 17 GB.
The picture data uses the MPEG 2
format, one of the worldwide standards
for digital compression technology. The
picture data is compressed to about 1/40
of its original size. The DVD VIDEO
also uses variable rate coding technology
that changes the data to be allocated
according to the status of the picture.
The audio data is recorded in Dolby
Digital as well as in PCM, allowing you to
enjoy more realistic audio presence.
Furthermore, various advanced functions
such as the multi-angle, multilingual, and
Parental Control functions are provided
with the DVD VIDEO.
137GB
Interlace format (Interlaced scanning)
The Interlace format is the NTSC
standard method for displaying TV
images at 30 frames per second. Each
frame is scanned twice-alternately
between the even numbered scanning
lines and then odd numbered scanning
lines, at 60 times per second.
Menu Playback
Playback using the menu screens
recorded on VIDEO CDs with PBC
functions. You can enjoy simple
interactive software using the menu
playback function.
Multi-angle function
Various angles, or viewpoints of the video
camera, for a scene are recorded on some
DVD VIDEOs.
Multilingual function
Several languages for the sound or
subtitles in a picture are recorded on
some DVD VIDEOs.
Multi Session
This is a recording method that enables
adding of data using the Track-At-Once
method. Conventional CDs begin at a
CD control area called the Lead-in and
end at an area called Lead-out. A Multi
Session disc is a disc having multiple
sessions, with each segment from Lead-in
to Lead-out regarded as a single session.
138GB
Parental Control
A function of the DVD VIDEO to limit
playback of the disc by the age of the
users according to the limitation level in
each country. The limitation varies from
disc to disc; when it is activated, playback
is completely prohibited, violent scenes
are skipped or replaced with other scenes
and so on.
Playback Control (PBC)
Signals encoded on VIDEO CDs (Version
2.0) to control playback. By using menu
screens recorded on VIDEO CDs with
PBC functions, you can enjoy playing
simple interactive programs, programs
with search functions, and so on.
Progressive format (sequential
scanning)
In contrast to the Interlace format,
the progressive format can reproduce
50 frames  60 frames per second by
reproducing all scanning lines (525
lines for the NTSC system, 625 lines
for PAL system). The overall picture
quality increases and still images, text
and horizontal lines appear sharper. This
format is compatible with the 525 or 625
progressive format.
Region Code
This system is used to protect copyrights.
A region code is allocated on each DVD
system or DVD VIDEO according to
the sales region. Each region code is
shown on the unit as well as on the disc
packaging. The system can play back
the discs that match its region code. The
system can also play back discs with the
“
” mark. Even when the region code
is not shown on the DVD VIDEO, the
region limit may still be activated.
Scene
On a VIDEO CD with PBC functions,
the menu screens, moving pictures and
still pictures are divided into sections
called “scenes.”
Title
The longest section of a picture or a
music piece on a DVD VIDEO; a movie,
etc., for a picture piece on video software,
or the entire album in audio software.
Track
A compact disc that contains moving
pictures.
The picture data uses the MPEG 1
format, one of the worldwide standards
for digital compression technology. The
picture data is compressed to about 1/140
of its original size. Consequently, a 12 cm
VIDEO CD can contain up to 74 minutes
of moving pictures.
VIDEO CDs also contain compact audio
data.
Sounds outside the range of human
hearing are compressed while the
sounds we can hear are not compressed.
VIDEO CDs can hold 6 times the audio
information of conventional AUDIO
CDs.
There are 2 versions of VIDEO CDs.
Version 1.1: You can play back only
moving pictures and sounds.
Version 2.0: You can play back highresolution still pictures and enjoy PBC
functions.
This system conforms to both versions.
* DivX and MPEG4 video files can only be
played back on MHC-GZR333i.
Additional Information
Section of a music or a picture on a
VIDEO CD, CD, or section of a music
on a CD.
VIDEO CD
139GB
Index
Numerics
D
K
16:9 60
4:3 LETTER BOX 60
4:3 PAN SCAN 60
5.1 Channel Surround 99,
101
DATE 100, 131
Demonstration 97
DivX 63, 136
Dolby Digital 136
DTS 136
DVD 8, 9
DVD+RW 8, 9, 137
DVD-RW 8, 9, 137
DVD VIDEO 137
Karaoke 90
KARAOKE MODE 90, 132
Karaoke Pon 92
Key Control 91
SCORE MODE 94, 132
VOCAL SELECT 92, 132
A
A/V SYNC 55, 131
AUDIO 60
AUDIO DRC 62
AUDIO SETUP 62
Auto Pause 136
E
EFFECT 49, 83, 132
Language code list 134
LANGUAGE SETUP 33, 59
M
B
F
BACKGROUND 62
Batteries 25
BLACK LEVEL 61
BLACK LEVEL
(COMPONENT OUT) 61
Fast forward 37
Fast reverse 37
FILE 54, 131
File 137
Film based software 137
FOLDER 54, 85, 131
Folder 137
Freeze Frame 37
Main unit 11
MEDIA 48
MENU 59
Microphone 90
MP3 9, 79
Multi-angle 38, 138
MULTI-DISC RESUME
39, 63
Multilingual 138
Multi Session Disc 121, 138
I
O
INDEX 43, 130
Instant Advance 38
Instant Replay 38
Interlace format 138
INTERVAL 49, 83, 131
ORIGINAL 42, 130
OSD 59
Other Component Hookup
100
C
CHAPTER 53, 130
Chapter 37, 136
COLD RESET 116
COLOR SYSTEM (VIDEO
CD) 61
COMPONENT VIDEO OUT
29, 101
Controlling the TV 31
Control Menu Display 129
CUSTOM 29, 56, 58
J
JPEG 48, 83
140GB
L
P
T
PARENTAL CONTROL 56
Parental Control 138
PAUSE MODE 61
PBC Playback 41
Playback Control (PBC) 138
PLAY LIST 42, 130
PROGRAM 50, 130
Program Play 50
PROGRESSIVE
(COMPONENT OUT)
29, 61
THEATRE SYNC 35
TIME 44, 130
Timer 95
TITLE 53, 130
Title 37, 139
TRACK 52, 85, 130
TRACK SELECTION 62
Transferring 73
Troubleshooting 103
TV Hookup 27
TV TYPE 60
Q
U
Quick setup display 33
Usable discs 8
USB 72
USB device 73
USB TRANSFER 74, 75, 132
R
Radio 64
Radio Stations 64
Rear panel 100
REC1 74
Recording 78
Region Code 139
Remote 16
REPEAT 53, 84, 131
Repeat Play 53, 84
RESET 116
V
VIDEO CD 8, 139
VIDEO SETUP 33, 60
W
WMA 79
S
Additional Information
SCENE 130
Scene 139
SCREEN SAVER 62
SETUP 131
Setup Menu 58
SHUFFLE 52, 84, 130
Shuffle Play 52, 84
Sleep Timer 95
Slow-motion Play 37
Sound Field 89
SPEAKER SETUP 63
SUBTITLE 60
SYSTEM SETUP 62
141GB
License and Trademark
Notice
This product incorporates copyright
protection technology that is protected
by U.S. patents and other intellectual
property rights. Use of this copyright
protection technology must be authorized
by Macrovision, and is intended for home
and other limited viewing uses only unless
otherwise authorized by Macrovision.
Reverse engineering or disassembly is
prohibited.
This system incorporates Dolby1) Digital and
DTS2) Digital Surround System.
1)
Manufactured under license from Dolby
Laboratories. “Dolby” and the doubleD symbol are trademarks of Dolby
Laboratories.
2)
Manufactured under license under U.S.
Patent #'s: 5,451,942; 5,956,674; 5,974,380;
5,978,762; 6,487,535 & other U.S. and
worldwide patents issued & pending. DTS
and the Symbol are registered trademarks,
& DTS 2.0+ Digital Out and the DTS logos
are trademarks of DTS, Inc. Product includes
software. ©DTS, Inc. All Rights Reserved.
“DVD+RW,” “DVD-RW,” “DVD+R,” “DVD
VIDEO,” and the “CD” logos are trademarks.
DivX is a video file compression
technology, developed by DivX, Inc. DivX,
DivX Certified, and associated logos are
trademarks of DivX, Inc. and are used under
license.
This product is an official DivX certified
product.
®
®
142GB
MPEG Layer-3 audio coding technology and
patents licensed from Fraunhofer IIS and
Thomson.
iPod is a trademark of Apple Inc., registered
in the U.S. and other countries.
“WALKMAN” and “WALKMAN” logo are
registered trademarks of Sony Corporation.
“Memory Stick” is a trademark of Sony
Corporation.
Windows Media is a registered trademark of
Microsoft Corporation in the United States
and/or other countries.
THIS PRODUCT IS LICENSED UNDER
THE MPEG-4 VISUAL PATENT
PORTFOLIO LICENSE FOR THE
PERSONAL AND NON-COMMERCIAL
USE OF A CONSUMER FOR
(i) ENCODING VIDEO IN COMPLIANCE
WITH THE MPEG-4 VISUAL STANDARD
(“MPEG-4 VIDEO”)
AND/OR
(ii) DECODING MPEG-4 VIDEO THAT
WAS ENCODED BY A CONSUMER
ENGAGED IN A PERSONAL AND NONCOMMERCIAL ACTIVITY AND/OR WAS
OBTAINED FROM A VIDEO PROVIDER
LICENSED BY MPEG LA TO PROVIDE
MPEG-4 VIDEO.
NO LICENSE IS GRANTED OR SHALL
BE IMPLIED FOR ANY OTHER
USE. ADDITIONAL INFORMATION
INCLUDING THAT RELATING TO
PROMOTIONAL, INTERNAL AND
COMMERCIAL USES AND LICENSING
MAY BE OBTAINED FROM MPEG LA,
LLC. SEE http://www. mpegla.com/
All other trademarks and registered
trademarks are of their respective holders.
In this manual, TM and marks are not
specified.
®
Additional Information
143GB
Download PDF

advertising