Audiovox FPE2608 Flat Panel Television User Manual

FPE2608
26” HD FLAT PANEL LCD TV
OWNER'S MANUAL
FOR ASSISTANCE CALL CUSTOMER SERVICE AT 1-800-645-4994
OR VISIT US AT WWW. AUDIOVOX.COM
PLV36260CS10 / AUDIOVOX
I/B 811-362691W080 <English>
SIZE : 148 X 210MM
MATERIAL : 80g WOODSFREE PAPER
128-8307
Printed in China
811-362691W080
SAFETY PRECAUTIONS
PLACEMENT INFORMATION
• Do not use this unit in places which are
extremely hot, cold, dusty or humid.
• Do not restrict the air flow of this unit by placing
it somewhere with poor air flow, by covering it
with a cloth, by placing it on bedding or carpeting.
WARNING : TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USERSERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
SAFETY INFORMATION
• When connecting or disconnecting the AC
power cord, grip the plug and not the cord itself.
Pulling the cord may damage it and create a
hazard.
• When you are not going to use the unit for a
long period of time, disconnect the AC power
cord.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
CONDENSATION INFORMATION
• When left in a heated room where it is warm
and damp, water droplets or condensation may
form inside the equipment. When there is
condensation inside the unit, the unit may not
function normally. Let the unit stand for 1-2 hours
before turning the power on or gradually heat
the room and let the unit dry before use.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
The symbol for Class II
(Double Insulation)
RATING PLATE LOCATION
The rating plate is located on the rear of unit.
CAUTION
• DANGER OF EXPLOSION IF BATTERY IS
INCORRECTLY REPLACED. REPLACE ONLY
WITH THE SAME OR EQUIVALENT TYPE.
• TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT OF
WALL OUTLET, THEN FULLY INSERT.
• USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
FCC STATEMENTS
NOTE: This unit has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This unit generates, uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio
communication. However, there is not guarantee
that interference will not occur in a particular
installation. If this unit does cause harmful
interference to radio or television reception, which
can be determined by turning the unit off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the unit and
receiver.
- Connect the unit into an outlet on a circuit
different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV
technician for help.
WARNING :
• TO PREVENT FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
DO NOT PLACE OBJECTS FILLED WITH LIQUIDS
ON OR NEAR THIS UNIT.
• SHOULD ANY TROUBLE OCCUR, DISCONNECT
THE AC POWER CORD AND REFER SERVICING
TO A QUALIFIED TECHNICIAN.
WARNING: Changes or modifications to this unit
not expressly approved by party responsible for
compliance could void the user authority to operate
the unit.
E-1
FPE2608_ib_eng_1-13.pmd
1
1/15/2008, 12:54 PM
IMPORTANT SAFETY INSTRUCTIONS
1)
2)
3)
4)
5)
6)
7)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
8) Do not install near any heat sources
such as radiators, heat registers,
stoves, or other apparatus (Including
amplifiers) that produce heat.
9) Do not defect the safety purpose of the
polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third
grounding prong. The wide blade or the
third prong is provided for your safety.
If the provided plug does not fit into your
wall outlet, consult an electrician for
replacement of the obsolete outlet.
10)Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and
the point where they exit from the
apparatus.
11) Only use attachments / accessories
specified by the manufacturer.
12)Use only with the cart, stand,
tripod, bracket, or table
specified
by
the
manufacturer, or sold with
the apparatus. When a cart is used, use
caution when moving the cart /
apparatus combination to avoid injury
from tip-over.
13)Unplug this apparatus during lightning
storms or when unused for long periods
of time.
14)Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as the power cord or plug is
damaged, liquid has been spilled or
objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally,
or has been dropped.
E-2
FPE2608_ib_eng_1-13.pmd
2
1/15/2008, 12:54 PM
CONTENTS
SAFETY PRECAUTIONS .................................................................................................................... 1
IMPORTANT SAFETY INSTRUCTIONS ........................................................................................... 2
CONTENTS ......................................................................................................................................... 3
ACCESSORIES .................................................................................................................................. 4
GETTING STARTED ............................................................................................................................ 4
CONTROL REFERENCE GUIDE ................................................................................................... 5 - 7
CONNECTIONS .......................................................................................................................... 8 - 12
Connecting a TV Antenna / Cable / Satellite ................................................................................... 8
Connecting an A / V Device ............................................................................................................ 8
Connecting Devices with a Composite (Yellow RCA-Type) Video Output ...................................... 9
Connecting Devices with a Composite (Yellow RCA-Type) Video Input ......................................... 9
Connecting a High Definition (HD) Source .................................................................................... 10
Connecting a PC ........................................................................................................................... 10
Connecting HDMI ........................................................................................................................... 11
Connecting an Audio Amplifier ...................................................................................................... 11
Connecting the AC Power Cord ................................................................................................... 12
USING HEADPHONES .................................................................................................................... 12
INSTALLATION ................................................................................................................................ 13
Removing the Base Stand ............................................................................................................ 13
Mounting on the Wall .................................................................................................................... 13
TV SETUP ................................................................................................................................ 14 - 19
Video Menu .................................................................................................................................. 14
Audio Menu .................................................................................................................................. 15
TV Menu ...................................................................................................................................... 16
Setup Menu ........................................................................................................................... 17 - 18
Parental Menu ....................................................................................................................... 18 - 19
TROUBLESHOOTING GUIDE .......................................................................................................... 20
E-3
FPE2608_ib_eng_1-13.pmd
3
1/15/2008, 12:54 PM
ACCESSORIES
Please check and identify the supplied accessories.
Remote Control (with batteries) ................................................................................................. x 1
GETTING STARTED
USING THE REMOTE CONTROL
• Point the remote control at the remote sensor located on the unit.
• When there is a strong ambient light source, the performance of the infrared remote sensor may be
degraded, causing unreliable operation.
• The recommended effective distance for remote operation is about 16 feet (5 meters).
TO INSTALL BATTERIES
1. Open the battery door.
2. Insert 2 “AAA” batteries.
_
+
_
+
BATTERY REPLACEMENT
When the batteries become weak, the operating distance of the remote control is greatly reduced and
you will need to replace the batteries.
CAUTION:
Danger of explosion if battery is incorrectly replaced.
NOTES
• If the remote control is not going to be used for a long time, remove the batteries to avoid damage
caused by battery leakage corrosion.
• Do not mix old and new batteries. Do not mix ALKALINE, standard (CARBON-ZINC) or rechargeable
(NICKEL-CADMIUM) batteries.
• Always remove batteries as soon as they become weak.
• Weak batteries can leak and severely damage the remote control.
• WARNING : Do not dispose of batteries in a fire. Batteries may explode or leak.
WARNING : Do not dispose of batteries in a fire. Batteries may explode or leak.
Many universal remote controls have a “learning” feature. We recommend you use that feature to
program the remote control.
For any questions or problems related to programming a universal remote control, you must contact the
customer service department of the universal remote control manufacturer for assistance, or refer to
the instructions included with the universal remote control. We cannot offer assistance in programming
universal remote controls.
E-4
FPE2608_ib_eng_1-13.pmd
4
1/15/2008, 12:54 PM
CONTROL REFERENCE GUIDE
REMOTE CONTROL
1.
STANDBY / ON button
Press to turn ON the unit or put it in
STANDBY (OFF) mode.
2. TV button
Press to switch to TV mode.
AV button
Press to switch to source connected to
AV 1 / AV 2 (composite) inputs.
HD button
Press to switch to source connected to
YUV (component) inputs and HDMI 1 /
HDMI 2 inputs.
DISPLAY button
Press to change disc status information
displayed on the screen.
3. Number (0 - 9) buttons
4. • [dot] button
Use to enter digital sub-channels. (i.e.
11.3 or 12.7)
5. MENU button
Press to display the on-screen TV menu.
6. VOLUME (- / +) buttons
Press to adjust the volume level.
7. CURSOR ( , , , ) buttons
Press to highlight selections on a menu
screen and adjust certain settings.
ENTER button
Press to confirm selections on a menu
screen.
8. CC button
Press to activate the Closed Captioning
feature. This function only works on
programs broadcasted with captions.
9. EXIT button
Press to exit the TV SET UP menu and
return directly to normal viewing.
10. SLEEP button
Press to set the SLEEP timer. The unit
will remain on for the time that is set,
and will automatically shut off
afterwards.
11. FUNCTION button
Press to switch between TV / AV 1 / AV 2 /
YUV in / HDMI 1 / HDMI 2 / PC in.
12. LAST CH button
Press to switch repeatedly between the
last two channels displayed.
button
13. MUTE
Press to turn off the sound.
/ CH buttons
14. CH
Press /
to change the channels.
15. MTS buttom
Press to switch between MONO sound,
STEREO sound and Secondary Audio
Program (SAP).
16. PICTURE button
Select from preset screen display
settings to match the type of show you
are watching. (Personal / Soft / Movie /
Standard / Dynamic)
17. SOUND button
Press to select from preset sound
settings to match the type of show you
are watching. (Standard / Personal /
Theater / Voice / Music)
18. FORMAT Button
Press to select the picture format.
E-5
FPE2608_ib_eng_1-13.pmd
5
1/15/2008, 12:54 PM
CONTROL REFERENCE GUIDE
FRONT & SIDE VIEWS
1. STD.BY / ON button
Turns the unit on and off.
2. MENU button
Enters the on-screen TV menu.
3. FUNCTION button
Selects TV / AV 1 / AV 2 / YUV in / HDMI 1 /
HDMI 2 / PC in.
4.
CH buttons
Confirms selections on the TV menu
screen and changes the TV channels.
5. - VOL + controls
Adjusts the volume level.
6. Removable stand
7. Color LCD screen
8. Remote sensor
Receives the remote control signal.
Standby indicator
9. Speaker
E-6
FPE2608_ib_eng_1-13.pmd
6
1/15/2008, 12:54 PM
CONTROL REFERENCE GUIDE
REAR VIEW
12
10
13
11
18
20
21
19
20
22
12
14
13
15
21
23
14
16
22
24
15
17
18
16
25
23
19
17
10. AUDIO IN (Left/Right) jacks (AV IN 2)
11. VIDEO IN jack (AV IN 2)
12. VIDEO IN jack (AV IN 1)
13. Headphones jack
14. TV ANTENNA terminal
15. AUDIO IN (Left / Right) jacks (AV IN 1)
16. S-VIDEO IN jack (AV IN 1)
17. AUDIO IN (Left / Right) jacks (YUV IN)
18. VIDEO / AUDIO OUT (Left / Right) jacks
(AV OUT)
19. PC IN MONITOR / VGA jack
20. AC Power Cord
21. HDMI jacks (HDMI IN 1 / HDMI IN 2)
22. PC IN AUDIO jack
23. Component Video input (Y / PB / PR)
jacks (YUV IN)
E-7
FPE2608_ib_eng_1-13.pmd
7
1/15/2008, 12:54 PM
CONNECTIONS
CONNECTING A TV ANTENNA / CABLE / SATELLITE
To view television channels correctly, a signal must be received from one of the following sources:
- An indoor or outdoor aerial antenna
- A cable system
- A satellite system
Connecting a Digital
Antenna
The tuner in this TV receives
ATSC TV signals from an
antenna.
This digital TV can receive
standard (SDTV) and high
definition (HDTV) over the air
broadcasts.
Satellite, cable or TV
antenna cable to TV
ANTENNA terminal
(cable not included)
Connecting an Analog
Antenna or Device
The tuner in this TV receives
NTSC TV signals, analog cable
signals or the RF output from a
satellite receiver, VCR or cable
box.
CONNECTING AN A/V DEVICE
To connect to other equipment such as a VCR, camcorder, satellite system or cable, etc.
Connecting to a VCR /
Camcorder / Satellite
System / Cable
To AUDIO
IN jacks
(AV IN 1)
Connect the AUDIO and S-VIDEO
cable (not included) as shown:
Make sure you connect the cable
from the other equipment (AUDIO
OUT and S-VIDEO OUT) to this
unit AV IN 1 (AUDIO IN and SVIDEO IN).
To S-VIDEO
IN jack
NOTE
Please refer to the user manual
for the other equipment for more
information.
To S-VIDEO OUT /
AUDIO OUT jacks
E-8
FPE2608_ib_eng_1-13.pmd
8
1/15/2008, 12:54 PM
CONNECTIONS
CONNECTING DEVICES WITH A COMPOSITE (YELLOW RCA-TYPE) VIDEO OUTPUT
To connect A/V devices such as a VCR, video game system or camcorder:
Connecting to a VCR / Video Game System / Camcorder
Connect the AUDIO / VIDEO cable (not included) as shown:
Make sure you connect the cable from the other equipment (AUDIO and VIDEO OUT) to this unit AV IN 1
(AUDIO and VIDEO IN) or AV IN 2 (AUDIO and VIDEO IN).
To AUDIO /
VIDEO IN jacks
(AV IN 1)
To AUDIO / VIDEO
OUT jacks
AV IN 1
OR
AUDIO IN
To AUDIO /
VIDEO IN jacks
(AV IN 2)
VIDEO IN
AV IN 2
To AUDIO / VIDEO
OUT jacks
NOTE
Please refer to the user manual for the other equipment for more information.
CONNECTING DEVICES WITH A COMPOSITE (YELLOW RCA-TYPE) VIDEO INPUT
To connect A/V devices such as a VCR, PVR or camcorder:
Connecting to a VCR /
PVR / Camcorder
Connect the AUDIO / VIDEO
cable (not included) as shown:
Make sure you connect the
cable from the other equipment
(AUDIO and VIDEO IN) to this
unit (AUDIO and VIDEO OUT).
NOTE
Please refer to the user manual
for the other equipment for more
information.
To AUDIO /
VIDEO OUT
jacks
To AUDIO / VIDEO IN jacks
E-9
FPE2608_ib_eng_1-13.pmd
9
1/15/2008, 12:54 PM
CONNECTIONS
CONNECTING A HIGH-DEFINITION (HD) SOURCE
High-Definition (HD) Devices with component video output must be connected to the YUV input.
Connect the component video cable and audio cable (not included) as shown.
Make sure you connect the component video cable and audio cable from the other equipment
(COMPONENT VIDEO OUT and AUDIO OUT) to this unit (COMPONENT VIDEO IN and AUDIO IN - YUV
IN).
To AUDIO
IN jacks
(YUV IN)
* May require a subscription
for
receiving
HD
channels. Check with
your cable/satellite service
provider for details.
To
COMPONENT
VIDEO IN jacks
(YUV IN)
To AUDIO
OUT jacks
To COMPONENT
VIDEO OUT jacks
NOTE
When connecting a DVD player to the television, the picture resolution is solely dependent upon the
resolution supported by the DVD player attached. DVD player resolutions vary from 480i to 1080i, and
this unit can support DVD players up to a maximum resolution of 1080i.
CONNECTING A PC
Connect the 15-pin D-SUB PC/VGA connector from your computer to the 15-pin D-SUB PC/VGA input on
this unit using a monitor cable and audio cable (not included) as shown.
Make sure you connect the
cable from the computer (PC
Connector and PC AUDIO) to
this unit (PC IN MONITOR / VGA
and AUDIO).
To PC AUDIO OUT jack
To PC connector
E - 10
FPE2608_ib_eng_1-13.pmd
10
1/15/2008, 12:54 PM
CONNECTIONS
CONNECTING HDMI
HDMI (High Definition Multimedia Interface) supports both video and audio on a single digital connection
for use with DVD players, DTV, set-top boxes and other digital AV devices. HDMI was developed to
provide the technologies of High Bandwidth Digital Content Protection (HDCP) as well as Digital Visual
Interface (DVI) in one specification. HDCP is used to protect digital content transmitted and received by
DVI-compliant or HDMI-compliant displays.
HDMI has the capability to support standard, enhanced or high-definition video plus standard to multichannel surround-sound audio. HDMI features include uncompressed digital video, a bandwidth of up to
2.2 gigabytes per second (with HDTV signals), one connector (instead of several cables and connectors),
and communication between the AV source and AV devices such as DTVs.
HDMI, the HDMI logo
and High-Definition Multimedia
Interface are trademarks or
registered trademarks of HDMI
licensing LLC.
Connect the HDMI cable (not
included) as shown:
Make sure you connect the
cable from the source
equipment (HDMI OUT) to this
unit (HDMI IN).
Press the HD button to match
the video source output quality.
To HDMI
OUT jack
To HDMI
IN jack
CONNECTING AN AUDIO AMPLIFIER
This connection allows you to use an audio amplifier and external speakers.
Connect the AUDIO cable (not
included) as shown:
Make sure you connect the
cable from the other equipment
(AUDIO IN) to this unit (AUDIO
OUT).
To AUDIO
OUT jacks
To AUDIO IN jacks
E - 11
FPE2608_ib_eng_1-13.pmd
11
1/15/2008, 12:54 PM
CONNECTIONS
CONNECTING THE AC POWER CORD
• Connect the AC power cord into a wall outlet.
• Press the STD. BY / ON button on the left side of the unit or use the remote control to turn on the unit.
NOTES
• TO PREVENT ELECTRIC
SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE
SLOT OF WALL OUTLET,
THEN FULLY INSERT.
• When the AC power cord is
plugged in, the unit is not
completely disconnected from
the main power, even when
the power is turned off.
• Be sure the AC power cord
is disconnected and all
functions are off before
making connections.
• Make sure that all the
components are connected
correctly.
• When you are not going to
use the unit for a long period
of time, disconnect the AC
power cord.
To AC wall outlet
USING HEADPHONES
• Turn down the volume before
connecting headphones to the
unit, then adjust the volume
to your desired level.
• When headphones are
connected, no sound will
come from the front
speakers.
Headphones
(1/8” [3.5mm]
diameter plug)
NOTE
Avoid listening to sound at high
levels for prolonged periods of
time. This may be harmful to you
and may cause hearing loss.
E - 12
FPE2608_ib_eng_1-13.pmd
12
1/15/2008, 12:54 PM
INSTALLATION
REMOVING THE BASE STAND
WARNING: The LCD display is very fragile, and must be protected at all times when removing the base
stand. Be sure that no hard or sharp objects, or anything that could scratch or damage the LCD display,
come in contact with it. Do NOT place pressure on the rear of the unit at anytime because the screen
could crack.
1. Disconnect any cables or
cords connected to the unit.
2. Lay the unit down on a flat
surface, so the back side is
facing up, making sure to
place a soft cushioned
material (such as a blanket
or thick piece of foam)
beneath the screen.
3. Remove the 8 screws and
then remove the BASE
STAND from the unit.
MOUNTING ON THE WALL
This unit is VESA-compliant, and is designed to be wall-mounted with a VESA-compliant 7 7/8” x 3 7/8”
(200mm x 100mm) mounting kit designed for flat-panel TVs (sold separately). Mount this unit according
to the directions included with the mounting kit.
NOTE
Remove the base stand before mounting the unit on the wall.
7 7/8”
3 7/8”
Six mounting
holes
E - 13
FPE2608_ib_eng_1-13.pmd
13
1/15/2008, 12:54 PM
TV SETUP
VIDEO MENU
1. Press the MENU button.
2. Press the ENTER or
button to select Video.
or
button to select the options (Picture Mode, Brightness, Contrast, Saturation,
3. Use the
Tint, Sharpness or Color Temperature). Adjust them using the
or
button (The screen will
button to go into the detailed settings.
change to your desired setting); or press the ENTER or
4. Press the EXIT button to return to the previous menu.
5. Repeat steps 3 and 4 to adjust other options.
6. To exit the MAIN MENU and return to the normal screen, press the EXIT button repeatedly.
TV MODE
Video
AV / YUV / HDMI MODE
Picture Mode
TV
Setup
Parental
Video
Personal
50
Brightness
Audio
Contrast
50
Saturation
50
Tint
0
Sharpness
4
Color Temperature
Audio
Setup
Parental
Audio
Setup
50
Contrast
50
Saturation
50
0
Video
Select EXIT Exit
4
Sharpness
Color Temperature
PC MODE
Video
Personal
Brightness
Tint
Standard
Video
Picture Mode
Standard
Select EXIT Exit
VGA SETTINGS IN PC MODE
Picture Mode
Personal
Video
Brightness
50
Contrast
50
Audio
VGA
Setup
Color Temperature
Standard
Parental
Parental
Video
Select EXIT Exit
VGA
Auto Adjust
H. Position
50
V. Position
50
Phase
3
Clock
127
Best definition
1,366 768
Select EXIT Return
Picture Mode
: Select from preset screen display settings to match the type of show you are
watching (Personal, Soft, Movie, Standard & Dynamic). (Select Personal mode
to recall your customed settings on brightness, contrast, saturation, tint,
sharpness and color temperature.)
Brightness
: Adjust the brightness of the picture. Brighten or darken the whole picture.
Contrast
: Adjust to sharpen the picture quality. The black portions of the picture become
richer in darkness and the white become brighter.
Saturation
: Adjust the color saturation of the picture.
Tint
: Adjust the tint of the picture. (Toward purple / Toward green)
Sharpness
: Adjust the sharpness level to improve detail in the picture.
Color Temperature : Adjust the three color temperature of the picture. Choose from Standard
(balanced), Warm (red white), or Cool (blue white) modes.
H. Position
: Center the image by moving it left or right.
V. Position
: Center the image by moving it up or down.
Phase
: Adjusts the image if there is flicker of screen letters, color misalignment, or
blurring.
Clock
: Adjusts the display clock to change width of the image.
- Resolution : 1,366 x 768 max
- Refresh Frequency : 60Hz max
E - 14
FPE2608_ib_eng_14-21.pmd
14
1/15/2008, 12:55 PM
TV SETUP
AUDIO MENU
1. Press the MENU button.
or
button to select Audio, then press the ENTER or
button to go into the Audio
2. Use the
settings.
3. Use the
or
button to select the options (Balance, Bass, Treble, Virtual Surround, Reverb or
Sound mode). Adjust them using the
or
button (The screen will change to your desired setting);
or press the ENTER or button to go into the detailed settings.
4. Press the EXIT button to return to the previous menu.
5. Repeat steps 3 and 4 to adjust other options.
6. To exit the MAIN MENU and return to the normal screen, press the EXIT button repeatedly.
TV MODE
AV / YUV / HDMI / PC MODE
NOTE
Experiment with different sound settings until you find the settings you prefer.
Balance
Bass
Treble
Virtual Surround
Reverb
Sound mode
:
:
:
:
:
Adjust the balance level toward the left or right speakers.
Adjust the bass range.
Adjust the treble range.
Switch on or off the virtual surround effect.
Select from preset sound settings (Concert, Living Room, Hall, Arena, Church,
Off) to match the type of show you are watching.
: Select from preset sound settings (Standard, Personal, Theater, Voice &
Music) to match the type of show you are watching. (Select Personal mode
to recall your custom settings on bass and treble.)
E - 15
FPE2608_ib_eng_14-21.pmd
15
1/15/2008, 12:55 PM
TV SETUP
TV MENU (For TV Mode Only)
1. Press the MENU button.
2. Use the
or
button to select TV. Press the ENTER or button to go into the TV settings.
3. Use the
or
button to select the options (Tuner Mode, Auto Scan, Auto Scan Add CH,
Channel Skip, MTS or Audio Language). Adjust them using the
or
button (The screen will
change to your desired setting); or press the ENTER or
button to go into the detailed settings.
4. Press the EXIT button to return to the previous menu.
5. Repeat steps 3 and 4 to adjust other options.
6. To exit the MAIN MENU and return to the normal screen, press the EXIT button repeatedly.
Video
Tuner Mode
Cable
Auto Scan
Audio
TV
Setup
Auto Scan Add CH
Channel Skip
MTS
Stereo
Audio Language
English
Parental
TV
Select EXIT Exit
Tuner Mode
: Antenna (over-the-air broadcasts, Ch 2-69) or Cable (cable/satellite broadcasts,
CH 1-135) mode is available.
Auto Scan
: Searches for usable stations and stores them in memory.
Auto Scan Add CH : Searches for more usable stations and adds them in memory. (The stations
stored before are still kept.)
Channel Skip
: Skip weak channels and the channels you do not like.
MTS
: Select from Stereo / SAP (Secondary Audio Program) / Mono.
Audio Language : Select from English / Spanish / French. (Available for digital channels if multiple
audio languages are broadcasted.)
NOTE
The SAP (Secondary Audio Program) feature allows a TV station to broadcast other information, which
could be audio in another language.
Channel Skip Setting:
1. Use the
or
button to select a channel. (Press the button to select the last channel of the page,
press again to go to the next page. Press the
button to select the first channel of the page, press
again to go to the previous page.)
2. Press the ENTER button to shift between skip or not skip the channel. (“ ” appears in the square
means skip the selected channel. The channel will not appear when you press the CH /CH
Button.)
Video
Audio
TV
Setup
Parental
2
Analog
3
Analog
4
Analog
5
Analog
5-1
Digital
6
Analog
7
Analog
8
Analog
9
Analog
10
Channel Skip
KPIX-DT
Analog
ENTER Enter
Select EXIT Return
E - 16
FPE2608_ib_eng_14-21.pmd
16
1/15/2008, 12:55 PM
TV SETUP
SETUP MENU
1. Press the MENU button.
2. Use the
or
button to select Setup. Press the ENTER or
button to go into the Setup settings.
3. Use the
or
button to select the options (OSD Language, Time Setup, Caption or Restore
setting). Adjust them using the
or
button (The screen will change to your desired setting); or
press the ENTER or button to go into the detailed settings.
4. Press the EXIT button to return to the previous menu.
5. Repeat steps 3 and 4 to adjust other options.
6. To exit the MAIN MENU and return to the normal screen, press the EXIT button repeatedly.
TV MODE
Video
AV / YUV MODE
OSD Language
Video
English
Time Setup
Audio
English
Time Setup
Audio
Caption
Restore setting
TV
OSD Language
Setup
Setup
Caption
Restore setting
Parental
Parental
Setup
Setup
Select EXIT Exit
Select EXIT Exit
HDMI / PC MODE
Video
OSD Language
OSD Language :
Select from English / Español / Français.
English
Time Setup
Audio
Restore setting
Setup
Parental
Setup
Select EXIT Exit
Time Setup Setting
Video
Time Zone
Video
Eastern Time
Time
Audio
Sleep Timer
Audio
Off
TV
TV
Setup
Setup
Parental
Parental
Time Setup
Time Zone
Sleep Timer
ENTER Enter
Time
Select EXIT Return
Time Update
Off
Date
2000/01/01
Time
07:42:49
Timer
Off
Power On Time
00:00:00
Power Off Time
00:00:00
ENTER Enter
Select EXIT Return
:Select the time zone from Eastern Time / Indiana / Central Time / Mountain Time / Arizona
/ Pacific Time / Alaska / Hawaii.
:Select the time to turn the unit to Standby mode automatically: Off -> 5 Minutes -> 10
Minutes -> 15 Minutes -> 30 Minutes -> 60 Minutes -> 90 Minutes -> 120 Minutes -> Off.
When you set the ‘Time’, the option will be shown:
Time Update
:Select On/Off to activate the following manual settings; Select Auto to synchronize time
with the digital TV channel signal.
Date
:Press the or button to locate the position, and press the number buttons to input date.
Time
:Press the or button to locate the position, and press the number buttons to input time.
Timer
:Select On to activate automatically power on/off.
Power On Time :Press the
or
button to locate the position, and press the number buttons to input
power on time.
Power Off Time :Press the
or
button to locate the position, and press the number buttons to input
power off time.
E - 17
FPE2608_ib_eng_14-21.pmd
17
1/15/2008, 12:55 PM
TV SETUP
Caption Setting
Video
Audio
Analog Closed Caption
Off
Digital Closed Caption
Off
Video
Audio
Digital Caption Style
TV
TV
Setup
Setup
Parental
Parental
Caption
ENTER Enter
Select EXIT Return
Caption Style
As Broadcaster
Font Size
Small
Font Style
Style 1
Font Color
Green
Font Opacity
Solid
Background Color
Black
Background Opacity
Translucent
Window Color
White
Window Opacity
Transparent
Digital Caption Style
Select EXIT Return
Analog Closed Caption : Select the analog closed caption or turn it off.
Digital Closed Caption : Select the digital closed caption or turn it off.
Digital Caption Style
: Select as Broadcaster to use the default digital caption style of the
broadcaster. Select Custom to activate the caption style items and set you
preferred detailed settings.
NOTE
This function only works on ATSC programs broadcast with captions.
Restore Setting
If you reset the TV to the factory settings, all your present settings on Video & Audio will be erased and
replaced by the factory’s default settings. However, picture settings in PC mode and Parental settings
will not be erased.
PARENTAL MENU
Password
1. Press the MENU button.
2. Use the
or
button to select Parental. Press the ENTER or button to confirm. The menu locked
screen will be displayed.
3. Enter a 4-digit password. Once entered, the screen will enter the Parental menu. The preset password
is 0000.
You can edit the parental control level or change the password. See Parental Control Settings on
the next page.
TV MODE
Video
AV / YUV / HDMI / PC MODE
Video
Password
Audio
Audio
TV
Setup
Setup
Parental
Password
Parental
Parental
Parental
Select EXIT Exit
Select EXIT Exit
If you forget the password,
enter " 8888 " to unlock parental control.
E - 18
FPE2608_ib_eng_14-21.pmd
18
1/15/2008, 12:55 PM
TV SETUP
Parental Control Setting
1. Use the
or button to select various Parental settings. Press the ENTER or button to go into the
detailed settings.
2. Use the , , and buttons to move among the rating levels. Press the ENTER button to change the
mode between Blocked and Allowed.
3. Press the EXIT button to return to the previous menu.
4. Repeat steps 1 - 3 to adjust other options.
5. To exit the MAIN MENU and return to the normal screen, press the EXIT button repeatedly.
Video
Video
Program Block
Rating Enable
On
U.S.TV Ratings
Change Password
Audio
Audio
Clean All
Setup
Setup
Parental
Parental
U.S. Movie Ratings
Canadian English Ratings
Canadian French Ratings
Parental
Program Block
Select EXIT Return
Open V-Chip
Select EXIT Return
Rating Enable : Select On to edit the following parental items. Select Off to disable parental control.
Open V-Chip : Reads the ratings from ATSC TV programs if there is rating information broadcasted,
and denies the channel when its rating is higher than the ratings you pre-set.
U.S.
TV
Ratings
U.S.
Movie
Ratings
Canadian
English
Ratings
Canadian
French
Ratings
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
G
PG
:
:
:
:
:
:
:
:
PG-13
:
R
:
NC-17
X
C
C8+
G
PG
:
:
:
:
:
:
14+
18+
G
8 ans+
13 ans+
16 ans+
18 ans+
:
:
:
:
:
:
:
Recommended for all children.
Recommended for all children age 7 and above.
General Audience.
Parental Guidance Suggested.
Parental Strongly Cautioned.
Mature Audience Only.
GENERAL AUDIENCES, Suitable for all ages.
PARENTAL GUIDANCE SUGGESTED - Some material may not be suitable for
children.
PARENTS STRONGLY CAUTIONED - Some material may be inappropriate for
children under 13.
RESTRICTED, Under 17 requires accompanying parent or adult guardian for
viewing in movie theaters.
No one 17 or under admitted in movie theaters,
Adults Only.
Children.
Recommended for children age 8 and older.
GENERAL AUDIENCES, Suitable for all ages.
PARENTAL GUIDANCE SUGGESTED - Some material may not be suitable for
children.
Viewers 14 years and older.
Adult Programming.
GENERAL AUDIENCES, Suitable for all ages.
Not recommended for young children.
Not suitable for children under the age of 13.
Not suitable for children under the age of 16.
Adult Programming.
E - 19
FPE2608_ib_eng_14-21.pmd
19
1/15/2008, 12:55 PM
TROUBLESHOOTING GUIDE
SYMPTOM
No power.
The remote does not
function.
TV
Bad Picture (snow,
multiple images,
distortion, blurry)
Black and white
picture.
No picture or sound.
Colored patches of
picture.
No sound is output
from the HDMI out
CAUSE (AND REMEDY)
•
•
•
•
•
•
Check that the AC power cord is connected.
The unit is not turned on.
Remove any obstacles between the remote and the unit.
Use the remote near the unit.
Point the remote at the remote sensor on the unit.
Replace the batteries in the remote with new ones.
• Check the location of the antenna and adjust it if necessary.
• Make sure the antenna cable is firmly connected.
• Make sure all input cables are firmly connected.
• Check the VIDEO MENU within the TV SETUP MENU.
• Check to make sure the program you are watching is broadcast in color and
not black & white.
• Make sure the unit is plugged in and turned on.
• Make sure that TV mode is selected.
• Try a new channel to check for possible station trouble.
• Make sure the antenna is connected properly.
• Increase the volume.
• Make sure the antenna or audio video source device is working properly.
• Make sure all cables are firmly connected.
• Check for local interference.
• Make sure there are no unshielded electrical devices nearby that are
causing interference.
• Turn the unit off for 30 minutes, then try it again.
• Check the connection between this unit and the HDMI out jack of other
equipment.
• See if the TV supports this 480p/576p/720p/1080i DVD system.
• Check your TV system setup correctly.
• Make sure your TV supports HDCP (High Bandwidth Digital Content
Protection).
E - 20
FPE2608_ib_eng_14-21.pmd
20
1/15/2008, 12:55 PM
Unit : INCH
26 1/4
22 5/8
19 3/4
8 1/4
18 3/4
5 1/8
7 7/8
8 5/8
3 7/8
E - 21
FPE2608_ib_eng_14-21.pmd
21
1/15/2008, 12:55 PM