Audiovox VE 1510DV TV DVD Combo User Manual

SAFETY PRECAUTIONS
The lightning flash with an arrowhead
symbol, within the equilateral triangle, is
intended to alert the user to the presence
of uninsulated "dangerous voltage" within
the product's enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
The following marks and symbols are located on
back of the unit.
The exclamation point within the
equilateral triangle is intended to alert the
user to the presence of important operating
and maintenance (servicing) instructions
in this owner’s manual.
Caution marking is located on back enclosure of the unit.
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION
INVISIBLE LASER RADIATION IS
EMITTED WHEN OPENED AND
INTERLOCKS DEFEATED.
AVOID EXPOSURE TO BEAM
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT OF WALL OUTLET,
THEN FULLY INSERT.
This product contains a
low power laser device.
The symbol for Class
(Double lnsulation)
On Placement
• Do not use the unit in places which are extremely hot, cold, dusty, or humid.
• Do not restrict the air flow of the unit by placing it in a place with poor air flow, by covering it with a cloth,
or by placing it on carpeting.
On Safety
• When connecting or disconnecting the AC power cord, grip the plug and not the cord itself. Pulling the
cord may damage it and create a hazard.
On Condensation
• When left in a heated room where it is warm and damp, water droplets or condensation may form inside
the unit. When there is condensation inside the unit, the unit may not function normally. Let the unit stand
for 1 to 2 hours before turning the power on, or gradually heat the room and allow the unit to dry before
use.
-1-
SAFETY PRECAUTIONS
FCC Information
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Shielded cables must be used with this unit to ensure compliance with the Class FCC limits.
WARNING: Should any trouble occur, disconnect the AC power cord and refer servicing to a
qualified technician.
Notes on Copyright
It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, or rent copyrighted material
without permission.
Apparatus Claims of "U.S. Patent Nos. 4,907,093; 5,315,448; and 6,516,132." licensed for limited viewing uses
only.
This product incorporates copyright protection technology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision,
and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision.
Reverse engineering or disassembly is prohibited.
-2-
IMPORTANT SAFETY INSTRUCTIONS
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with a dry cloth.
7.
Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions.
8.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. When the provided plug does
not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
Portable Cart Warning
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as the power-supply cord or plug is damaged, liquid has spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
-3-
TABLE OF CONTENTS
Safety
Precautions
.............................1-2
Important Safety Instructions
Table of Contents
Repeat Playback ............................................. 19
................. 3
DVD Programmable Memory ........................... 20
................................. 4
DVD Programmable Memory ........................ 20
Disc Formats ........................................ 5
Viewing JPEG FILes ....................................... 20
Accessories .......................................... 6
Play Modes for CD or JPEG Disc .................... 21
Remote Control ..................................... 6
Customizing the Function Settings ............ 22-23
Control Reference Guide .................... 7-9
Language ................................................... 22
Mounting Instructions ........................ 10-11
Video ........................................................... 22
Connections ................................................. 12-13
Default ........................................................ 23
Connecting the TV Antenna .........................12
Using the TV .................................................... 24
Connecting the Unit to a TV or
TV Setup ..................................................... 25-27
other Video Equipment .................................. 12
Listening to the Radio ..................................... 28
Connecting the Unit to a Stereo Receiver
Troubleshooting Guide ..................................... 29
or Amplifier .................................................. 12
Maintenance .................................................... 30
Plugging in the Unit ..................................... 13
Specifications ................................................. 30
Monitor Operation ........................................... 13
Unit Operation ................................................. 14
Sound System ................................................... 14
Setting the Clock .............................................. 15
Setting the Cooking Timer ............................... 15
Playing a Disc ................................. 16-18
Playing a Disc .............................................. 16
Pausing Playback .......................................... 16
Stopping Playback ...................................... 16
Skipping to a Different Chapter/Track ........... 16
Fast Forward/Fast Reverse .......................... 16
Angle Selection ........................................... 17
Subtitle Selection ........................................ 17
Audio Selection .......................................... 17
Display Function ......................................... 18
Special Functions ........................................... 18
Locating a Specific Title/Chapter/Time ......... 18
Locating a Specific Track ............................ 18
Setting Favorite Bookmark
During Playback .......................................... 19
-4-
DISC FORMATS
The unit can play
DVDs
[8cm/12cm disc]
Compatible
Audio CDs
[8cm/12cm disc]
Region Management Information
Region Management Information: This unit is designed and manufactured to respond to the Region
Management Information that is encoded on DVDs. If the region number printed on the DVD does not
correspond to the region number of this unit, this unit cannot play that disc.
The region number of this unit is 1.
Disc Function or Operation that is Not Available
When the “ ” symbol appears on the screen, it indicates that the function or operation attempted is not
available at that time. This occurs because the DVD manufacturer determines the specific functions. Certain
functions may not be available on some discs. Be sure to read the documentation provided with the DVD.
Icons Used on DVDs
Sample lcons
Language selections for audio
Language selections for subtitles
Screen aspect ratio
Multiple camera angles
Region code indicator
Note:
• When playing a CD-G (Graphics) or CD EXTRA disc, the audio portion will be played, but the graphic
images will not be shown.
Titles, Chapters and Tracks
• DVDs are divided into “titles” and “chapters”. If the disc
has more than one movie on it, each movie would be a
separate “title”. “Chapters” are sections of titles.
• Audio CDs are divided into “tracks”. A “track” is usually
one song on an Audio CD.
Note : Numbers identify each title, chapter, and track on a disc. Most discs have these numbers recorded
on them, but some do not.
Notes on Unauthorized Discs
You may not be able to play back some DVDs on this unit if they were purchased from outside your
geographic area or made for business purposes.
-5-
ACCESSORIES
Please Check and Identify the Included Accessories.
Remote control ............................................................................................................................. x 1
AAA 1.5V battery .......................................................................................................................... x 2
Mounting template ......................................................................................................................... x 1
1.06" (27mm) spacers .................................................................................................................. x 4
.57" (14.4mm) spacers ................................................................................................................. x 4
.32" (8.2mm) spacers ................................................................................................................... x 4
#M 5 x 69 mm screws .................................................................................................................... x 4
#M 5 x 40 mm screws ................................................................................................................... x 4
Warranty Card .............................................................................................................................. x 1
Registration Card .......................................................................................................................... x 1
REMOTE CONTROL
Using the Remote Control
• This remote control is magnetic and can be attached to most refrigerators. Some refrigerators panels
are not metallic. In this case, try attaching the magnetic remote control to the side of the refrigerator.
• Point the remote control at the REMOTE SENSOR located on the unit.
• When there is a strong ambient light source, the performance of the infrared REMOTE SENSOR may
be degraded, causing unreliable operation.
• The recommended effective distance for remote operation is about 16 feet (5 meters).
To Install Batteries
1. Open the battery door.
2. Insert two AAA batteries.
Battery Replacement
When the batteries become weak, the operating distance of the remote control is greatly reduced and you
will need to replace them.
Caution: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent
type.
Notes:
• Do not place the remote control near magnetic devices or magnetic cards.
• If the remote control is not going to be used for a long time, remove the batteries to avoid corrosion
damage caused by battery leakage.
• Do not mix old and new batteries. Do not mix ALKALINE, standard (CARBON-ZINC) or rechargeable
(NICKEL-CADMIUM) batteries.
• Always remove batteries as soon as they become weak.
• Weak batteries can leak and severely damage the remote control.
• WARNING: Do not dispose of batteries in a fire. Batteries may explode or leak.
-6-
CONTROL REFERENCE GUIDE
Remote Control
FUNCTION Button
Use to select DVD, TV or RADIO mode.
2) PICTURE Button
Selects from preset screen display
settings to match the type of show you
are watching.
3) MEMORY Button
Sets title/chapter in a favorite order.
Enter the number of a selected station.
Button
4) EXIT/RETURN
Press to exit the TV menu and return
directly to normal viewing.
5) DVD MENU Button
Press to enter the main menu of the
DVD you are watching.
6) VOLUME (+/-) Buttons
Adjusts the volume.
7)
/
TUNING Buttons
: Fast reverse playback.
: Fast forward playback.
TUNING
: Scans all available
radio stations.
8)
PREV Button
Selects previous titles, chapters or
tracks on a disc.
9) ANGLE Button
During DVD playback, switch the
camera angle of the video presentation
when scenes with multiple camera
angles are recorded on a DVD.
10) GOTO Button
Goes directly to a location on a DVD/
CD.
11) AUDIO Button
Selects audio soundtracks of a DVD or
change the output mode of a CD.
MTS Button
Press to select MONO sound,
STEREO sound or Secondary Audio
Program (SAP).
12) FORMAT Button
Press to select the picture format.
1)
PICTURE
1
2
1
2
3
4
5
6
7
8
9
LAST CH
3
0
TV MENU
EXIT
4
RETURN
DVD MENU
MUTE
5
6
STOP
BAND
7
8
9
10
11
SOUND
FORMAT
MTS
12
-7-
CONTROL REFERENCE GUIDE
Remote Control
13) STANDBY/ON Button
Turns on the unit and puts it in standby
mode.
14) Number (0-9) Buttons
15) LAST CH Button
Press to switch repeatedly between the
last two channels displayed.
16) TV MENU Button
Press to display the on-screen TV
menu.
17) CURSOR ( , , , ) Buttons
Use to highlight selections on a screen
and make adjustments to certain
settings.
CH- buttons
CH+ /
Use to change TV channels.
ENTER Button
Confirm selections on a menu screen.
PICTURE
13
1
2
3
4
5
6
7
8
9
14
LAST CH
15
0
TV MENU
EXIT
16
Button
18) MUTE
Press to turn off the sound.
STOP/BAND Button
19)
Stops playback.
Switches between AM and FM.
PLAY Button
Starts playback.
PAUSE Button
Pauses playback, frames advance.
20)
NEXT Button
Selects next titles, chapters or tracks
on a disc.
21) SOUND Button
Press to select from preset sound
settings to match the type of show you
are watching.
22) SUBTITLE Button
Selects one of the subtitle languages
programmed on a DVD.
23) SETUP Button
Enters and exits the SETUP menu of
the DVD.
REPEAT Button
Repeats chapter or title of a DVD.
Repeats single track or whole CD.
24) DISPLAY Button
Changes disc status information
displayed on the screen.
RETURN
17
DVD MENU
MUTE
18
STOP
19
BAND
SOUND
FORMAT
20
21
22
23
MTS
24
-8-
CONTROL REFERENCE GUIDE
Unit
1
2
3 45 678
9 10 11 12 13 14
15
1)
2)
3)
4)
5)
6)
7)
8)
9)
Disc Tray
Opens or closes the tray by pressing OPEN/
CLOSE button.
Place a disc on the disc tray, label side up.
Display Window
Displays system information.
POWER ON Indicators
DVD :
DVD indicator
TV :
TV indicator
RADIO : RADIO indicator
Remote Sensor
Receives the remote control unit signals.
POWER Button
Turns the unit on and off.
OPEN/CLOSE Button
Use to open/close the disc tray.
DVD/TV/RADIO Button
Use to select DVD, TV or RADIO mode.
PLAY Button
Press to start or resume playback of a disc.
STOP/BAND Button
Stops playing a disc.
Switches between AM and FM.
ADJUST
Buttons
Makes adjustments to certain settings.
10)
11)
12)
13)
14)
15)
-9-
SET CLOCK Button
Use to set the current time.
/
/
CH
Buttons
Button
to go back to previous chapters/
Press
tracks.
Button
Press
to advance to chapters / tracks.
Use to search for a station automatically or
select presetted stations.
CH
Buttons
Use to skip/search TV channel.
TV MENU Button
Opens and closes the TV menu.
VOLUME +/- Buttons
Adjusts the volume levels.
TIMER Button
Use to set the cooking timer.
ENTER Button
Use to enter the sub-menu and confirm
selections in TV mode.
Screen
MOUNTING INSTRUCTIONS
TOOLS NEEDED: 1) Electric drill with 1/4” bit; 2) Phillips-head (cross style) screwdriver.
STEP 1
If your cabinet does NOT have an overhang:
a) Place the Mounting Template in the desired
location inside or underneath the cabinet
(whichever has less obstructions, and will be
easier for you to reach to drill holes), flush
with the front edge of the cabinet and tape it
down. Go to STEP 2.
STEP 3
If your cabinet does NOT have an overhang:
a) Eight screws are included with this unit, but
you will only need four of them. Select the
screw length which will go completely through
your cabinet bottom, and provide at least 3/8"
of thread to screw into the main unit.
b) Insert the four selected screws through each
hole from the inside of the cabinet going down
(see Figure4).
If your cabinet DOES have an overhang:
a) Measure the thickness of the cabinet overhang
(see Figure 1).
Cabinet Bottom
Front
edge
Figure 1
b) Fold the Mounting Template along the guideline
that is closest to the thickness of your cabinet
overhang.
c) Tape Mounting Template to the underside of
the cabinet with the folded portion of the
Mounting Template flush up against the cabinet
overhang (see Figure 2). Go to STEP 2.
Figure 4
c) Hold the unit up against the bottom of the
cabinet, and align the four holes on the top of
the unit with the screws. Partially tighten each
screw, but do not fully tighten the screws until
all of them have been started.
d) Gently tighten each screw until they are firmly
holding the unit in place.
Cabinet Bottom
Front
edge
Template
If your cabinet DOES have an overhang:
Figure 2
STEP 2
Use an electric drill with a ¼” drill bit (not included)
to drill all four holes marked on the Mounting
Template (see Figure 3). To reduce splintering, place
a small piece of masking tape over each hole
location before drilling. Go to STEP 3.
Figure 3
a) Eight screws are included with this unit, but you
will only need four of them. Select the screw
length which will go completely through your
cabinet bottom, and extend at least 3/8" past
the bottom of your cabinet overhang.
b) This unit includes three sets of four spacers of
various lengths. The spacers can be put
together to form longer spacers to
accommodate various cabinet overhang
thicknesses. Determine the best combination
of spacers which is equal to or longer than the
cabinet overhang thickness.
(Continued on next page)
- 10 -
MOUNTING INSTRUCTIONS
(Continued from previous page)
c) Insert the four selected screws through each
hole from the inside of the cabinet going down
(see Figure 5).
e) Partially tighten each screw, but do not fully
tighten the screws until all of them have been
started (see Figure 6).
Figure 6
Figure 5
d) Hold each screw head down and push the unit
and spacers onto the screws, then hold the
unit up until spacers are firmly against the
bottom of the cabinet (and fully nested within
each other if you are using multiple spacers
for each screw).
f) Gently tighten each screw until they are firmly
holding the unit in place. The top front edge of
the unit should clear the overhang.
CAUTION
TO REDUCE THE RISK OF FIRE, DO NOT PLACE ANY HEATING OR COOKING
APPARATUS BENEATH THIS UNIT.
MOUNTING SUGGESTIONS
1) If your cabinet has obstructions inside it which prevent you from using the template, cut out the
corresponding area on the template, but do NOT cut out or through the screw holes.
2) If your cabinet has obstructions underneath it, which will interfere with the mounting of the unit, remove
the obstruction before mounting the unit, or find another location to mount the unit.
3) It is recommended that you wear safety glasses while drilling to prevent eye injuries.
4) For wood cabinets, you may want to mark the hole locations with a nail, pressed gently but firmly into
the wood so that a slight impression is made. This will also help keep the drill bit centered in the right
location.
5) Hold the drill firmly against the cabinet to keep the drill from “walking”.
- 11 -
CONNECTIONS
Connecting the TV Antenna
Connect a TV antenna or CATV cable or Satellite system to the TV antenna terminal.
TV antenna
2
To the TV ANT IN
terminal
1
FM ANTENNA
Connecting the Unit to a TV or other Video Equipment
Use the Audio/Video cable (not supplied). Connect the VIDEO OUT and R/L (right/left) AUDIO OUT jacks
on the rear of the unit to the VIDEO IN and R/L (right/left) jacks on your TV or other video equipment.
FM ANTENNA
TV or other Video
Equipment
VIDEO
IN
(yellow)
L
(white)
AUDIO
IN
(red)
R
Audio/Video cable (not supplied)
Connecting the Unit to a Stereo Receiver or Amplifier
ANALOG CONNECTION
Use the Audio cable (not supplied). Connect the R (right) AUDIO OUT and L (left) AUDIO OUT jacks on
the rear of the unit to the R (right) AUDIO IN and L (left) AUDIO IN jacks on your other source.
FM ANTENNA
Stereo Receiver or
Amplifier
(White)
L
AUDIO IN
(Red)
Audio cable (not supplied)
- 12 -
R
CONNECTIONS
Plugging in the Unit
Plug the AC power cord into the wall outlet
a) Before plugging in the power cord, make sure the voltage of the unit matches your local voltage.
b) Plug the power cord directly into the nearest wall outlet, and wrap the remaining cord around the cord
storage knob at the rear of the unit.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT OF
WALL OUTLET, THEN FULLY INSERT.
AC power cord
FM ANTENNA
To AC outlet
MONITOR OPERATION
Follow the illustrations below to open the monitor.
1. Gently pull the monitor down from the back, and twist it clockwise so the screen is visible.
2. The screen can be turned up to 270o. Do NOT force the screen once it stops turning. The screen
does NOT turn completely around.
- 13 -
UNIT OPERATION
Turning the Unit On
While the power cord is connected and the unit is on standby, power will be consumed and only the clock
display will flash.
• Press the
POWER button to turn the unit on and the DVD indicator lights up.
After a short period of time, “DVD” will appear on the front display and the DVD logo (start-up picture) will
appear on the screen.
• Press the DVD/TV/RADIO button (the FUNCTION button on the remote control) to TV mode and the TV
indicator lights up.
After a short period of time, “TV” will appear on the front panel display and the TV program will begin on the
screen.
• Press the DVD/TV/RADIO button (the FUNCTION button on the remote control) to RADIO mode and the
radio indicator lights up.
After a short period of time, “TUNER” and the FM frequency will appear on the front panel display.
SOUND SYSTEM
Dolby Digital (for DVD)
Dolby Digital is a technology developed by Dolby Laboratories. Soundtracks encoded in Dolby Digital can
reproduce from one to 5.1 discrete channels of excellent quality audio.
The unit automatically recognizes the Dolby Digital bitstream and provides a downmix suitable for twochannel listening. An additional Dolby Digital decoder is required for reproduction of the discrete multichannel soundtracks available on many DVDs.
Manufactured under license from Dolby Laboratories.
‘Dolby’ and
the double-D symbol are trademarks of Dolby Laboratories.
- 14 -
SETTING THE CLOCK
To adjust the clock, the unit must be in standby mode. To enter standby mode, make sure that the unit is
plugged in, but not turned on.
•
Check that the rated voltage of the unit matches your local voltage.
1. When the AC power cord is plugged in, the
clock display will blink.
/
buttons to set the current
3. Press the
hours then press the SET CLOCK button once
to confirm. Then, the MINUTE blinks.
2. Press the SET CLOCK button until the HOUR
blinks.
4. Press the
/
buttons to set the current
minutes then press the SET CLOCK button
once to start the clock.
SETTING THE COOKING TIMER
1. Press the TIMER button. The “TIMER” indicator
appears and the cooking time “10” blinks.
3. When the preset time elapses, the ALARM will
sound.
2. Press the
/
buttons to select your
desired time from 1-99 minutes.
4. To turn OFF the ALARM, press the TIMER
button once. Otherwise, the ALARM will
automatically turn off after 60 minutes if no button
is pressed.
• Press the TIMER button repeatedly to select
time: 10, 15, 30, 45, 60, 75, 90 minutes.
• Press and hold the
/
buttons to fast
forward/reverse the cooking time.
CANCELLING THE COOKING TIMER
•
Press the TIMER button until the time of the cooking timer shows "OFF". The “TIMER” indicator will
disappear.
- 15 -
PLAYING A DISC
This owner’s manual explains the basic instructions of this unit. Some DVDs are produced in
a manner that allows specific or limited operation during playback. Such as, the unit may not
respond to all operating commands. This is not a defect in the unit. Refer to the instruction
notes of discs.
“
” may appear on the screen during operation. A “
permitted by the unit or disc.
” means that the desired operation is not
Playing a Disc
1. Press the
POWER button to turn on the unit.
2. Press the DVD/TV/RADIO button (the FUNCTION button on the remote) to select DVD mode.
See CUSTOMIZING THE FUNCTION SETTINGS (page 22 to 23) before proceeding to step 3.
OPEN/CLOSE button. The disc tray opens.
3. Press the
4. Place a disc onto the disc tray with the label side up.
5. Press the
OPEN/CLOSE button. The disc tray closes.
It takes a short while for your unit to load the disc. After loading, the unit will automatically either bring
you to the main menu of the DVD or start playback of the disc.
6. If the unit does not automatically start playing the DVD, press the PLAY button.
• When MUTE is pressed, the sound is mute and the “L O”
indicator always blinks on the LCD display until MUTE is
pressed again or VOL is pressed.
Pausing Playback (Still Mode)
Press the PAUSE button on the remote. To resume normal playback, press the
Each time you press the PAUSE button, the picture advances one frame.
PLAY button.
Stopping Playback
Press the STOP button at the location where you want to interrupt playback. To resume playback at the
position where the disc was stopped, press the
PLAY button.
If you press the STOP button twice, the unit’s memory will be cleared and pressing the
will reset the disc to the beginning.
PLAY button
Skipping to a Different Chapter/Track
•
•
•
Press the
button repeatedly to skip to the start of the current or previous chapter/track.
Press the
button to skip to the next chapter/track.
For an audio CD, use the number buttons (remote control only) to go directly to that track number.
Fast Forward/Fast Reverse
1. Press the TUNING
or
TUNING button on the remote control when a disc is playing.
• The disc begins fast scan at x2 speed.
• Four speeds are available. Each time the TUNING
or
TUNING button is pressed, the speed
of fast scan changes in the following sequence:
2. Press the
speed.
PLAY button when you have reached the desired point to resume playback at normal
Notes:
• The DVD player mutes sound during reverse and forward scan of DVD video discs.
• The fast playback speed may differ depending on the disc.
- 16 -
PLAYING A DISC
Angle Selection
Some DVDs contain scenes which have been shot from a number of different angles. For these discs,
the same scene can be viewed from each of these different angles.
1. While you are playing a DVD with different angles
recorded, press the ANGLE button to view the number of current angles available.
2. Press the ANGLE button repeatedly to change the
scene to the next angle in those recorded.
• About two seconds later, playback continues from
the new angle selected.
Sequence of angle shots
(Example)
• If no button is pressed within 10 seconds, playback
continues without changing the current angle.
Notes:
• This function can only be used for discs on which scenes shot from multiple angles have been
recorded.
• If only one angle is recorded, “
” is displayed.
Subtitle Selection
1. While a DVD is playing, press the SUBTITLE button to display the current language setting, as
shown in the example below.
2. Press the SUBTITLE button repeatedly to select the desired subtitle language.
Notes:
• If only one language is recorded, the language does not change.
• About two seconds later, playback continues with the new subtitle selected.
• The number of languages recorded differs depending on the disc.
• If no button is pressed within a few seconds, playback continues without changing the current subtitle.
• This function can only be used for discs on which subtitles have been recorded in multiple languages.
• On some DVDs, subtitles are activated from the main menu of the DVD. Press the DVD MENU button
to activate the main menu.
Audio Selection
On some discs, the sound is recorded in two or more formats. Follow the directions below to select the
type of playback.
1. While a disc is playing, press the AUDIO button to show the current audio format number.
2. Press the AUDIO button repeatedly to select the desired audio format.
Notes:
• If only one audio format is recorded, the number does not change.
• Some DVD discs allow you to change audio selections only via the disc menu. If this is the case,
press the DVD MENU button and choose the appropriate language on the disc menu.
• You can select different audio channels (Left, Right, Mix or Stereo) on an audio CD by pressing the
AUDIO button repeatedly.
- 17 -
PLAYING A DISC
Display Function
While the disc is playing, press the DISPLAY button on the remote control repeatedly to display information
on operation status.
Time:
The elapsed time from the beginning of the title
which is currently playing.
Title/Chapter: The number of the title/chapter currently playing
and total titles/chapter on disc.
Audio:
The type of the audio currently selected is
displayed.
Subtitle:
The subtitle number and language currently
selected is displayed. When a disc with only one
subtitle is played back, “
” is displayed.
Angle:
The current angle is displayed. When a disc with
only one angle is played back, “
” is displayed.
SPECIAL FUNCTION
Locating a Specific Title/Chapter/Time
If a DVD contains title/chapter/time numbers, you can locate a specific title/chapter/time by directly
selecting a title/chapter/time number.
1. Press the GOTO button to display Title.
2. Press the or button on the remote to select the option (Title,
Chapter or Time) then press the corresponding number button(s)
for the Title/Chapter/Time you want.
3. Press the ENTER button to confirm. The unit will start playback
about 3 seconds later.
Locating a Specific Track
If a CD contains track numbers, you can locate a specific track by directly selecting track number.
1. Press the GOTO button.
2. Press the or button on the remote to select the option (Track,
Time or Disc Time) then press the corresponding number button(s)
for the Track/Time/Disc time you want.
3. Press the ENTER button to confirm. The unit will start playback
about 3 seconds later.
Notes:
• If the time numbers you entered is not permited by the DVD, after you press the ENTER button, it will
restore to “- - : - - : - -”. You should re-enter correct numbers.
• Some discs may not respond to this process.
• Some scenes may not be located as precisely as you specified.
• This method for accessing specific locations is available only within the current title of the DVD.
- 18 -
SPECIAL FUNCTION
Setting Favorite Bookmarks During Playback
While a disc is playing, you can mark the desired scene.
1. Press the GOTO button until Bookmark1 appears.
2. Press the ENTER button to mark the desired scene and the time of
this point will be shown in Bookmark1.
3. Press the ENTER button to play the favorite bookmark.
To Set Other Bookmarks
1. Press the GOTO button until Bookmark1 appears, then use the
or
button on the remote to select Bookmark2/Bookmark3.
2. Press the ENTER button.
Notes:
• Some discs may not work with marking operation.
• The marking is cancelled when you open the disc tray or turn the unit off.
REPEAT PLAYBACK
You can play a specific title or chapter repeatedly.
Repeating a Chapter
You can play the same chapter repeatedly.
1. While the disc is playing, press the REPEAT DISC button until the “
the screen. The current chapter is played repeatedly.
Repeating a Title
You can play the same title repeatedly.
2. While the disc is playing, press the REPEAT DISC button until the “
the screen. The current title is played repeatedly.
To Resume Normal Playback
3. While the disc is playing, press the REPEAT DISC button until the “
screen.
” indicator displays on
” indicator displays on
” indicator displays on the
You can play a single track or whole disc repeatedly.
Repeating a Single Track
You can play the same track repeatedly.
1. While the disc is playing, press the REPEAT DISC button on the remote control until the “
indicator displays on the screen. The current track is played repeatedly.
”
Repeating a Whole Disc
2. While the disc is playing, press the REPEAT DISC button on the remote control until the “
indicator displays on the screen. The whole disc is played repeatedly.
”
To Resume Normal Playback
3. Press the REPEAT DISC button until the “
” indicator
displays on the screen.
You can play a single track or the entire CD repeatedly through the
Toolkit which appears on the right in the window.
While the disc is playing, use the and buttons on the remote to select
"Repeat", then press the ENTER button to select Single/All/Off.
Single: Repeat the current track.
All:
Repeat the entire CD.
Off:
Resume normal playback
- 19 -
DVD PROGRAMMABLE MEMORY
DVD Programmed Playback
You can combine your favorite titles/chapters and play them in the order you determine.
1. Press the MEMORY button on the remote control.
2. Use the or button to select the title you want, then press the
ENTER button on the remote control to confirm.
3. Use the or button to select the chapter you want, then press
the ENTER button on the remote control.
4. Use the button to move the cursor to the top of the chapter list
and press the ENTER button to return to Title window. Then repeat
steps 2 to 3 to add additional titles and chapters.
5. Press the
PLAY button to start the programmed playback.
To Change the Programmed Selections
1) Press the MEMORY button.
2) Press the button to select “Clear”, then press the ENTER button
to clear them one by one.
3) Follow above steps 1-4 of DVD Programmable Memory to program
the new title and chapter.
To Resume Normal Playback from Programmed Playback
1) Press the MEMORY button.
2) Press the
button to select “Clear All”, then press the ENTER
button. All the programs will be cleared.
3) Press the
PLAY button to resume normal playback.
Notes:
• Some discs may not permit memory playback operation.
• To exit the Program menu, press the MEMORY button.
• The programmed selections will be cleared when you open the disc tray or turn off the DVD player.
VIEWING JPEG FILES
This unit can play JPEG files recorded on a CD-R/RW discs.
Viewing JPEG Files
1. Open the disc tray.
2. Place a disc onto the disc tray with the label side up.
3. Close the disc tray. A list of folders/files will appear on the screen.
or
button to select your desired file, the selected
4. Press the
picture will appear in the lower right corner.
5. Press the PLAY button to start playback. Press the STOP button
to display a folder list.
Notes:
• You can press the PAUSE button to freeze the picture, and press the PLAY button to resume slide
show.
• You can press the STOP button to quit playback.
• You can use the number buttons on the remote control to jump immediately to the desired picture.
• You can press the ANGLE buttonon the remote control to rotate direction of the picture by 90o.
• Some discs may not permit this operation.
- 20 -
PLAY MODES FOR CD OR JPEG DISC
When playing CD/JPEG discs, you can modify the Play Modes through the Toolkit which appears on the
right in the window. Press the or button on the remote control to navigate between the left/right windows
and the or button on the remote control to select files/tracks or play mode items. Then press the ENTER
button.
CD Track/JPEG File Programmed Playback
1. Use the and buttons on the remote to select "Edit mode" then
press the ENTER button.
2. Use the cursor buttons ( , , , ) to select tracks/files shown on
the left side of the window, then press the ENTER button. " " will
appear in front of the selected tracks/files.
3. Use the
and
buttons to select "Add to program", press the
ENTER button. " " will disappear from the screen. It means that
the tracks/files you selected have been added into the "Program
view".
4. Use the
or
button to select "Program view" and press the
ENTER button to view programmed files.
5. Press the
PLAY button to start the program playback.
Note: When programming the JPEG files, it should be in STOP mode.
Clear the Programmed Tracks/Files
•
Press the
STOP button twice to stop playback.
1. Use the and buttons on the remote to select "Edit mode" then
press the ENTER button.
2. Use the
or
button to select "Program view", then press the
ENTER button. The programmed tracks/files appear on the left
side of the window.
3. Use the cursor buttons ( , , , ) to select the programmed
tracks/files, then press the ENTER button. " " will appear in front
of the selected tracks/files.
4. Use the and buttons to select “Clear program” then press the
ENTER button.
Note: It is disabled if the "Edit mode" item is not selected.
The Toolkit has the following play mode items:
• Repeat (Off/Single/All):
Off: Resumes normal playback.
Single: Repeats the current track/file.
All: Repeats all files on the current folder or all tracks on the disc.
•
•
•
•
•
•
Mode (Normal/Shuffle/Music Intro):
Normal: Resumes normal playback.
Shuffle: Playbacks track/file in random order.
Music Intro: Only playback the first 10 seconds of all tracks on the disc.
Edit mode: Program operation works only when "Edit mode" is selected.
Program view: To view tracks/files in the "Program view" list. It is disabled when the "Program view"
list is empty.
Add to program: Add files/tracks to the "Program view" list. It is disabled if the "Edit mode" item is not
selected.
Browser view: To view files/tracks in the original view list.
Clear program: Delete the files/tracks in the "Program view" list.
Note: The program will be deleted if disc tray is opened.
- 21 -
CUSTOMIZING THE FUNCTION SETTINGS
Language
OSD Language
1. Press the SETUP button in stop mode.
button to select OSD Language.
2. Press the
3. Press the button. Use the
or button to make adjustments,
then press the ENTER button.
The screen will change to your selected language immediately.
4. Press the EXIT button to return to the normal screen.
Subtitle
1. Press the SETUP button in stop mode.
2. Press the button. Use the or button to select Subtitle.
3. Press the
button. Use the
or button to make adjustments,
then press the ENTER button.
4. Press the EXIT button to return to the normal screen.
Notes:
• Some DVDs may be set to display subtitles in a different language
other than the ones you selected. A prior subtitle language may be
programmed on the disc.
• Some DVDs allow you to change subtitle selections via the disc
menu only. If this is the case, press the DVD MENU button and
choose the appropriate subtitle language from the selection on the
disc menu.
Audio
1. Press the SETUP button in stop mode.
2. Press the button. Use the or button to select Audio.
3. Press the button. Use the or
button to make adjustments,
then press the ENTER button.
4. Press the EXIT button to return to the normal screen.
Note: Some DVDs may not play in the selected language. A prior
language may be programmed on the disc.
DVD Menu
1. Press the SETUP button in stop mode.
2. Press the button. Use the or button to select DVD Menu.
3. Press the
button. Use the
or button to make adjustments,
then press the ENTER button.
4. Press the EXIT button to return to the normal screen.
Note: Some DVDs may not include your pre-selected language. In
this case, the DVD player automatically displays disc menus consistent
with the disc's initial language setting.
Video
TV Shape
1. Press the SETUP button in stop mode.
2. Press the or button to select VIDEO.
3. Press the button. Use the or button to select TV Shape.
4. Press the button. Use the or
button to make adjustments,
then press the ENTER button.
5. Press the EXIT button to return to the normal screen.
- 22 -
CUSTOMIZING THE FUNCTION SETTINGS
Notes:
• The displayable picture size is preset on the DVD. Therefore, the playback picture of some DVDs may
not conform to the picture size you select.
• When you play DVDs recorded in the 4:3 picture size only, the playback picture always appears in the
4:3 picture size regardless of the TV Shape setting.
• Select 16:9 to conform the LCD screen on the unit. Always be sure that your TV Shape conforms to the
actual TV in use if you connect the unit to a TV.
View Mode
1.
2.
3.
4.
Press the SETUP button in stop mode.
Press the or button to select VIDEO.
Press the button. Use the or button to select View Mode.
Press the button. Use the or button to select the option (Fill,
Original, Auto Fit or Pan Scan), then press the ENTER button.
5. Press the EXIT button to return to the normal screen.
Fill:
Fill the screen with decoded image.
Original: Display image as it’s original size.
Auto Fit: Automatically fit the decoded image on screen without distortion. Black bars will be present on
top/bottom or left/right of screen.
Pan Scan: Select when a standard 4:3 TV is connected. Displays pictures cropped to fill your TV screen.
Sides of the picture are cut off.
Note: Depending on the DVDs, you may not be able to view the mode as selected.
Smart Picture
1.
2.
3.
4.
Press the SETUP button in stop mode.
Press the or button to select VIDEO.
Press the button. Use the or button to select Smart Picture.
button. Use the
or
button to select the option
Press the
(Standard, Bright, Soft or Dynamic), then press the ENTER button.
5. Press the EXIT button to return to the normal screen.
Standard: Picture is set to normal brightness.
Bright:
Picture is brighter.
Soft:
Softer image effect.
Dynamic: It includes 4 items (Brightness, Contrast, Tint and Color).
Use the or button to make adjustments.
Default
Use Default Settings
1.
2.
3.
4.
Press the SETUP button in stop mode.
Press the or button to select DEFAULT.
Press the
button, then press the ENTER button.
Use the
or
button to select “YES”, then press the ENTER
button. The original setting will be restored. The unit will exit setting
menu automatically and reload the disc in the disc tray.
Note: It will take 3-5 seconds to reset the DVD player to the factory
default.
- 23 -
USING THE TV
Connect a TV antenna or CATV cable or Satellite system to the TV antenna terminal before
searching TV channels
1. Connect the TV antenna.
2. Connect the AC power cord.
POWER button to turn on the unit.
3. Press the
4. Press the DVD/TV/RADIO button (the FUNCTION button on the
remote) to select TV mode.
Manual searching for TV channels
1. Press the TV MENU button, then press the button to TV CHANNEL
SETTING.
2. Press the button to select ANTENNA. Use the or button to select
Air or CATV.
3. Use the button to select Auto Scan.
4. Press the ENTER button to enter sub menu of Auto Scan.
5. Use the button to select “Start to Scan” in the sub menu.
6. Press the ENTER button to start the search for TV channels.
7. The screen will show the first received channel when auto search is
completed.
RF CH
13
Found
0
PRESS MENU TO EXIT AUTO SCAN
Watching Television
Viewing a television station after the auto/manual search for channels.
1. Press the FUNCTION button to TV mode.
2. Press the
CH
buttons (the CH+ or CH- button on the remote) to select a channel, or press
the number button on the remote to select the channel you want to watch.
• For channels 1 to 9, enter one-digit channel number.
• For channels 10 to 99, enter the two-digit channel number.
• For channels 100 or over, enter three-digit channel number.
Note:
• When a channel is selected, the channel number is displayed on the top right corner of the screen. This
number will disappear after a few seconds.
• When MUTE is pressed, the sound is mute and the “L O” indicator always blinks on the LCD display
until MUTE is pressed again or VOL is pressed.
ATSC TV mode:
Press the DISPLAY button, the upper window will
pop up, then press the DISPLAY button again,
the lower window will pop up. Press the DISPLAY
button once to exit.
NTSC TV mode:
Press the DISPLAY button, the upper window will
pop up, then press the DISPLAY button once to
exit.
- 24 -
TV SETUP
Picture Setting
1. Press the TV MENU button.
2. Use the or button to select the options (Picture Mode
/ Contrast / Brightness / Sharpness / Tint / Color).
3. Use the or button to make adjustment. The screen will
change to your selected mode immediately. Press the TV
MENU button to return to the previous menu.
Picture Mode
Standard
Contrast
50
4. Repeat steps 2 and 3 to adjust other options.
Brightness
Sharpness
50
50
5. To exit the TV SETUP MENU and return to the normal
screen, press the EXIT button on the remote control.
Tint
0
Color
50
NOTE: You can also access these setting by pressing the
PICTURE button.
UP/DOWN
ADJUST “MENU”:EXIT
Picture Mode: Select from preset screen display settings to match the type of show you are watching
(Standard, Dynamic, Soft & Personal).
Contrast:
Adjust to sharpen the picture quality. The black portions of the picture become richer in
darkness and the white become brighter.
Brightness: Adjust to brighten or darken the whole picture.
Sharpness: Adjust the sharpness level to improve detail in the picture.
Tint:
Adjust natural skin tones in the picture quality.
Color:
Adjust the color of the picture.
Sound Setting
1. Press the TV MENU button.
2. Use the
or
button to select SOUND SETTING.
3. Use the or button to select the options (Sound Mode /
Bass / Treble / Balance / Audio Language).
4. Use the
or
button to make adjustment. Press the TV
MENU button to return to the previous menu.
5. Repeat steps 2 to 4 to adjust other options.
6. To exit the TV SETUP MENU and return to the normal
screen, press the EXIT button on the remote control.
NOTE: You can also access these setting by pressing the
SOUND button.
Sound Mode
Standard
Bass
50
Treble
Balance
50
0
Audio Language
UP/DOWN
English
ADJUST “MENU”:EXIT
Sound Mode:
Select from preset sound settings (Standard, Music, Movie, Personal) to match the
type of show you are watching.
Bass:
Adjust the bass range.
Treble:
Adjust the treble range.
Balance:
Adjust the balance level toward the left or right speakers.
Audio Language: Use the or button to select English, French or Spanish (Available for Digital TV
system only).
NOTE: Only for DTV/ATSC input source mode, thus it is not available in other input source mode.
- 25 -
TV SETUP
TV Timer Setting
1. Press the TV MENU button.
2. Use the
or
button to select TIMER SETTING.
3. Use the or button to select the options (OSD Duration
/ Time Zone / Day Saving Time).
4. Use the or button to make adjustment. Press the TV
MENU button to return to the previous menu.
5. Repeat steps 2 to 4 to adjust other options.
OSD Duration
30 Sec
Time Zone
Day Saving Time
Eastern
Off
Clock
----/--/-- --:--
6. To exit the TV SETUP MENU and return to the normal
screen, press the EXIT button on the remote control.
OSD Duration: Select amount the time of TV menu showing
on screen.
UP/DOWN
ADJUST “MENU”:EXIT
Time Zone / Day Saving Time / Clock
1. Set the local Time Zone, eg. Pacific.
2. After selecting the time zone, the Day Saving Time must be activated for those areas observing such
change.
3. The clock will be recorded automatically (for ATSC only).
Note: TV TIMER SETTING is different from the CLOCK & COOKING TIMER setting on page 15, please
set both settings.
Misc Setting
1. Press the TV MENU button.
2. Use the
or
button to select MISC SETTING.
3. Use the or button to select the options (Language /
Color Mode / Restore Setting).
4. Use the or button to make adjustment. The screen will
change to your selected mode immediately. Press the TV
MENU button to return to the previous menu.
5. Repeat steps 2 to 4 to adjust other options.
6. To exit the TV SETUP MENU and return to the normal
screen, press the EXIT button on the remote control.
Language :
Select from English / Français / Español.
Color Mode :
Adjust the three color temperature of the picture. Select Normal (balanced) / Warm
(red white) / Cool (blue white) mode.
Restore Setting: If you reset the TV to the factory settings, all your present settings on picture & sound
will be erased and replaced by the factory’s default settings.
- 26 -
TV SETUP
TV Channel Setting
1. Press the TV MENU button.
2. Use the or button to select TV CHANNEL SETTING.
3. Use the
or
button to select the options (Antenna /
Auto Scan / Auto Scan Add CH / Channel Skip /
Channel No. / Channel Label).
4. Use the or button to make adjustment. The screen will
change to your selected mode immediately. Press the TV
MENU button to return to the previous menu.
5. Repeat steps 2 to 4 to adjust other options.
6. To exit the TV SETUP MENU and return to the normal
screen, press the EXIT button on the remote control.
NOTE: Channel No. : 2-69 Channel for Air, 1-135 Channel for
CATV.
Antenna :
Select “CATV” to receive cable signal.
Select “AIR” to receive air signal.
Auto Scan :
Automatically search all channels for
those with adequate signal strength.
Auto Scan Add CH: The stored channels can not be cleared
and the Auto Scan Channels will be
added.
If you has selected CATV in TV
CHANNEL SETTING, then you can
select Cable System (AUTO / STD /
HRC / IRC) in the sub menu as the
picture shown.
Channel Skip:
You may switch ON/OFF the skip
function of each stored channel by
selecting the channel with or button
(and using or button to select page
if the amount of stored channels in
more than 1 page), and followed with
pressing the ENTER button.
Channel Label: You may edit one label for each channel.
1. Select the Channel Label item and press the
to go into the channel label edit screen.
2. Use the
or
3. Use the
or
character.
or
button
button to enter the number or letter.
button to move and edit for the next
4. After editing, press the DISPLAY button and the Channel
& Channel Label will be shown on the screen.
- 27 -
Antenna
Air
Auto Scan
Auto Scan Add CH
Channel Skip
Channel No.
Channel Label
UP/DOWN
ADJUST “MENU”:EXIT
LISTENING TO THE RADIO
Tuning in to a Station Manually
1. Press the DVD/TV/RADIO button (the FUNCTION button on the
remote) until the radio frequency appears on the front panel display.
2. Press the STOP • BAND button to select AM or FM.
3. Press the
TUNING
buttons on the remote to tune in to a
desired station.
•
When MUTE is pressed, the sound is mute and the “L O” indicator
always blinks on the LCD display until MUTE is pressed again or
VOL is pressed.
FM Stereo
Press the MTS button on the remote until “
panel display.
” appears on the front
Weak FM stations
Press the MTS button on the remote until “ ” appears on the front
panel display. Background noise will be reduced. To restore stereo
reception, press the MTS button on the remote to select “ ”.
Searching for a Station Automatically
• Press and hold the
/
button on the front panel or the
TUNING
buttons on the remote until
the tuner starts searching for a station, then release. After tuning in a station, the search stops.
• The search may not stop at a station with a very weak signal.
Presetting Stations
The unit can store a total of 60 stations in memory (30 FM, 30 AM). Presetting allows you to tune in to a
station directly.
1. Press the DVD/TV/RADIO button (the FUNCTION button on the remote) to RADIO.
2. Press the STOP • BAND button to select AM or FM.
3. Press the number button on the remote to select the preset number.
• For preset numbers 1 to 9 simply press the number button on the remote.
• For preset numbers 10 to 30, enter the two-digit numbers.
For example, to enter 18 by pressing “1” & “8”.
TUNING
4. Press the
buttons to tune in to a desired station.
5. Press the MEMORY button twice on the remote.
6. Repeat steps 2-5 to store other stations.
Tuning in to a Preset Station
1. Press the DVD/TV/RADIO button (the FUNCTION button on the remote) to RADIO.
2. Press the STOP • BAND button to select AM or FM.
/
button repeatedly to select the number of the preset station or use the numbered
3. Press the
buttons to enter the number of the preset station.
For Better Reception
FM: Fully unwind the FM antenna wire. Then extend the FM antenna wire and place it in the position that
sounds best.
Note: Do not connect the FM antenna to an outside antenna.
- 28 -
TROUBLESHOOTING GUIDE
SYMPTOM
CAUSE (AND REMEDY)
No power.
• Ensure the AC power cord is connected.
• The unit is not turned on.
The remote does
not function.
•
•
•
•
DVD
No sound or only a
very low-level
sound is heard.
Remove any obstacles between the remote and the unit.
Use the remote near the unit.
Point the remote at the remote sensor on the unit.
Replace all batteries in the remote with new ones.
• Make sure that you've selected DVD mode.
• The system is in pause mode. Press the PLAY button to return to normal play
mode.
• Fast forward or fast reverse is performed. Press the PLAY button to return to
normal play mode.
• The DTS DVD cannot be decoded to have speaker output.
• This unit is too hot. Shut off the unit for 30 minutes to allow it to cool down.
No picture
• The region number of the disc doesn't match the region number of this unit.
The picture is not
clear
• Clean the disc.
• The disc is scratched.
Severe hum or
noise is heard.
• Clean the disc.
The disc does not
play.
•
•
•
•
TV
Snowy picture,
multiple image,
picture distorted,
picture blurred and
noisy sound.
There is no disc inside ("No Disc" appears on the screen).
Insert the disc correctly with the label side facing up on the disc tray.
Clean the disc.
A non-NTSC disc has been inserted. The unit and disc region number are incompatible.
• Condensation may have formed inside the unit due to a sudden change in temperature. Wait about an hour for it to clear and try again.
• Check antenna location, direction or connection.
No color of picture.
• Check the PICTURE SETTING in the TV SETUP MENU.
No picture and
sound.
•
•
•
•
•
•
•
Colored patches of
picture.
• Magnetic interference from unshielded equipment.
• Turn OFF the unit for 30 minutes, then turn ON again.
Not plugged into AC outlet.
Make sure that you've selected TV mode.
Try a new channel to check for possible station trouble.
Make sure the antenna is connected to properly.
Increase the volume.
The antenna is broken.
Check for local interference.
- 29 -
MAINTENANCE
Cleaning the Disc
A defective or soiled disc inserted into the unit can cause sound to drop out during playback.
Handle the disc by holding its inner and outer edges.
•
Do NOT touch the surface of the unlabeled side of the disc.
•
Do NOT stick paper or tape on the surface.
•
Do NOT expose the disc to direct sunlight or excessive heat.
•
Clean the disc before playback. Wipe the disc from the center
outward with a cleaning cloth.
•
NEVER use solvents such as benzine or alcohol to clean the disc.
•
Do NOT use irregular shaped discs (example: heart shaped, octagonal, etc.). They may cause malfunctions.
Cleaning the Unit
Clean plastic cover over screen if it becomes dirty with oil, grease, dust, etc while cooking. Please follow
below steps.
•
Be sure to turn the unit off and disconnect the AC power cord before cleaning the unit.
•
Wipe the unit with a dry soft cloth. If the surfaces are extremely dirty, wipe clean with a cloth which has
been dipped in a weak soap-and-water solution and wrung out thoroughly. Then wipe with a dry cloth.
•
Never use alcohol, benzine, thinner, cleaning fluid or other chemicals. Do NOT use compressed air to
remove dust.
Important Note
Before transporting the unit, remove the disc from the disc compartment.
SPECIFICATIONS
Power source:
AC 120V ~ 60Hz
Specifications and external appearance are subject to change without notice.
- 30 -
Printed in China
811-390991W010