Auto Page C3-RS-665 Remote Starter User Manual

C3-RS-665
PROFESSIONAL REMOTE CAR STARTER
&
3 CHANNEL SECURITY SYSTEM
OPERATIONS MANUAL
Compatible
Please register your product at:
www.autopageusa.com
THIS PRODUCT IS DESIGNED FOR PROFESIONAL
INSTALLATION ONLY
1
SYSTEM OPERATIONS:
WARNINGS:
As with any product that performs automatic functions, there are certain safety
precautions that you must practice and be aware of.
1.
2.
3.
4.
5.
6.
7.
Keep the transmitter out of children’s reach.
Do not leave anyone in the vehicle while running on remote control.
Alert servicing personnel that the vehicle can be started automatically.
Do not start the vehicle by remote while it’s in an enclosed area or garage.
Always apply the parking brake and lock the vehicle as you exit the vehicle.
The vehicle windows must be rolled up.
Should the unit malfunction, disconnect the fuse until the problem is
corrected.
8. The use and operations of this system is the sole responsibility of the
operator.
9. Some areas may have local ordinances that prohibit leaving a vehicle
running on public streets.
10. It is not safe to remote start the vehicle if the vehicle is parked on a steep
incline.
Transmitter
Button
System Function
Remark
Lock Doors & Arm System
Panic function
Press and Hold for 3 seconds
Car Locator
Under armed mode
-
Arm and Delete The 2 Stage Shock
Sensor
Press twice within 3 seconds
+
Silent Arming / Disarming
Ignition in "off" position.
Unlock Doors & Disarm System
+
II
Two Steps Door Unlock & Disarm
System
Trunk Release (Channel 2)
Press twice within 3 seconds.
Press and Hold for 2 seconds
Passive Arming By-pass
While the system Disarmed.
Activate or Turn Off The Remote
Start
Safety start requires two pushes
Channel # 3 Auxiliary Output
Press both buttons together
Switching code For 2nd Car
Operation.
For regular remote transmitter Only
2
CHANGING THE BATTERY IN YOUR TRANSMITTERS
XT-33: This transmitter uses two (2) 3-volt lithium ion batteries (#CR2016)
that are sandwiched together with the (+) side facing upward. To replace
the battery, you will need to use a small flat blade screwdriver. Locate the
small notch on the lower right side of the transmitter case next to the key
ring. Using the flat blade screwdriver, carefully pry the top case from the
bottom case. It should snap apart after breaking the seal. Before
removing the batteries note the direction of the positive (+) terminal.
Place the new batteries in exactly the same manner, being careful not to
bend or damage the contact terminal. Snap the cases back together and
then test the transmitter to insure it arms and disarms the alarm.
(2) CR2016
3-Volt Batteries
ACTIVE LOCK & ARM:
1. Press
button on the transmitter.
2. The siren will chirp once and parking lights will flash once indicating that
the system is now armed. The vehicle doors will lock upon arming when
interfaced with the keyless entry system.
SILENT ARMING / DISARMING: Pressing the
+
buttons
together on the transmitter will arm or disarm your system, No chirp sound
will be heard, arm / disarm confirmation will be through the
vehicles parking lights only.
DEFECTIVE SENSOR REMINDER: If the siren sounds 3 chirps, then you
have left a door, trunk, or hood lid ajar.
3
SHOCK SENSOR / OPTIONAL SENSOR BY-PASS:
Press the
button once: The siren chirps once, The system is armed.
Press the
button a second time within 5 seconds: The siren chirps
twice, the Shock Sensor is now bypassed. The sensor bypass feature is
programmed to activate for one arming cycle only. The security system will
return to normal operation during the next arming cycle.
B. PASSIVE ARMING
Active arming / disarming is controlling your security system via the
remote transmitter. This security system is equipped with an optional
Passive Arming feature, which allows the security system to arm 30
seconds after the last door is closed. Operation is as follows:
1. Turn the ignition to the “OFF” position and exit the vehicle.
2. After all entrances are closed, the security system LED will flash fast
for 30 seconds. If you re-open any door / hood / trunk, the security
system LED will stop flashing. It will begin flashing again once the
vehicle all entrances are closed.
After 30-second timer has elapsed, the security system will automatically
“ARM”. The siren will chirp [1] time and the parking lights will flash [1]
time.
PASSIVE ARMING WITH PASSIVE DOOR LOCKING
The vehicle doors will automatically lock after passive arming cycle has
been completed. Please refer to your installing dealer to activate this
feature.
PASSIVE ARMING BY-PASS: While the LED is fast flashing for passive
arming or Automatic re-arm, Press the
buttons twice, the security will
respond with [1] chirp and LED will turn “ON”. The security system will
remain in this temporary state for as long as you wish.
To exit passive by-pass, press the
or
button and the system will
return to normal status.
ACTIVE UNLOCK & DISARMING:
1. Press
button on the transmitter.
2. The siren will chirp twice and parking light will flash twice to indicating
that the security system is now disarmed. The vehicle doors will
unlock and dome lights will turn on for 30 seconds.
TAMPER DISARMING: If the alarm was triggered in your absence, upon
disarming the system, the siren will chirp 4 times, the parking lights will
flash 3 times.
PATHWAY ILLUMINATION
4
This feature turns the parking light “ON” for 30 seconds upon a unlock
signal and for 10 seconds upon the lock signal.
TWO STEPS DOOR UNLOCK: This feature will independently unlock the
driver door only when deactivating the system. Pushing the
button a second time within 3 seconds will unlock the entire vehicle.
Please refer to your installing dealer to install and activate this feature.
LED DISPLAY:
LED
Off
Slow
Flash
Function
Disarmed
On (Solid)
Valet Mode
LED
2 flashes...
pause
3 flashes...
pause
4 flashes...
pause
5 flashes...
pause
Armed
Function
Zone 1 / Warn-Away Trigger
Zone 2 / Trigger Trunk/Hood
Zone3/ Trigger on Door
Switch
Zone4/Trigger on Impct
Sensor
Zone 5 / Trigger Ignition
Switch
CHIRP INDICATOR:
Chirp
Function
Parking light
Function
1 chirp
Arm
1 flash
Arm
2 chirps
2 flashes
Disarm
4 chirps
Disarm
Defective
Reminder
Disarm / Triggered
12 flashes
Car Locator
6 chirps
Car Locator
Constant On
Under Remote Start
3 chirps
3 flashes
Disarm / Triggered
PARKING LIGHTS:
1. Arming
Siren / Horn
1 or 3 Chirps
Parking Light
LED
Doors
1 Flash
Slow Flash Locking
2. Disarming
2 or 4 Chirps 2 or 3 Flashes
3. Trigger
4. Panic
Alarming
Alarming
Flashes
Flashes
5. Car Locator
6 Chirps
12 Flashes
Starter
Disable
Unlocking
Slow Flash
Disable
Dome Light
Turns on for
30 -second
Flashes
Flashes
Locking
AUTOMATIC RE-ARM
If this feature is selected, the security system will automatically re-arm
itself 60 seconds after disarming with remote transmitter. Automatic
rearm will cancel if any door is opened before the 60 seconds timer has
5
elapsed. Please refer to your installing dealer to activate this feature.
DEACTIVATING WITHOUT A TRANSMITTER
The Override function may be used if the remote transmitter is lost or
inoperative.
1. Enter the vehicle and turn the ignition switch to ‘ON’ position.
2. Within 10 seconds push and release the valet switch
If starter disable is installed. You can now start and operate the
vehicle normally.
VALET MODE:
The valet switch allows you to temporarily bypass all system function,
eliminating the need to hand your transmitter to parking attendants or
garage mechanics. When the system is in valet mode, and remote start
functions are bypassed, however the remote panic feature and remote
door locks will remain operational. To use the valet mode, the system
must first be deactivated either by using you remote transmitter, or by
operating the Manual override sequence.
Enter Valet Mode:
1.From the Unlock condition, turn the ignition to “ON” position.
2.Push and hold valet switch for 2 seconds until the LED turns on. The
LED will remain on as long as the system is in ‘valet mode’.
Exit Valet Mode:
1. Return to normal operation, turn ignition ‘on’.
2. Push and hold valet switch for 2 seconds, The LED will turn off
indicating the system has exited the valet mode.
PANIC FUNCTION:
The transmitter can be used as a remote panic switch to manually
trigger the vehicle’s siren / horn in case of emergency.
1.Press and hold the
button for 3 second. The siren / horn will
immediately sound.
2.During panic mode, the normal function of this transmitter button will
be suspended. The
and
buttons can be used to lock and
unlock the doors (if the option is installed), however once the button is
pressed, the vehicle’s starter disable device, (where installed) will be
enabled allowing the vehicle to start.
3.To stop the panic, press and hold the
or
button on the
transmitter again for 3 seconds. Also if any transmitter button other
than the
or
button is pressed and released, the panic mode will
be turned off immediately.
6
4. If no buttons are pressed, the panic function will stop automatically in
60 seconds.
TRIGGER THE SYSTEM
When armed, your vehicle is protected as follows:
1. Light impacts will trigger the warn-away with 3 long chirps from
siren/horn.
2. Heavy impacts / Doors open / Hood open / Trunk open / Turn on the
ignition key will all trigger the programmed sequence.
The starter disable relay (if installed) prevents the vehicle’s starter from
cranking. The siren, horn, parking lights, and dome light will turn on
alerting of an intrusion for 30 seconds. Then it will stop and automatic
reset and re-arm. If one of the sensors or detectors is still active, the alarm
system will sound a maximum of 6 times of 30 seconds cycles.
DOME LIGHT CONVENIENCE DELAY & SUPERVISION
This system is a unique feature, which will turn on your vehicle dome
light as following: (optional) Additional installation required.
1. Upon unlocking, the interior lights will remain on for 30 seconds.
2. If the vehicle is intruded, the interior light will flash for the same duration
as the siren.
Note: Turning on the ignition switch or activating the system will turn off
the dome light.
IGNITION CONTROL DOOR LOCKS.
If the vehicle’s door locks have been interfaced to the security system,
the system will automatically lock the vehicle’s doors when the ignition
is turned “ON” and /or unlock the vehicle’s doors when the ignition is
turned “OFF”.
TRUNK RELEASE
Press and hold the
button on transmitter for two seconds to remote
control the trunk release or other electric devices.
CAR LOCATOR
Press the
button once with armed mode to active car locator function.
The horn will chirp 6 times. The parking light will flash 12 times, for you to
easily locate your car.
REMOTE START OPERATION:
WARNINGS:
As with any product that performs automatic functions, there are certain
safety precautions that you must practice and be aware of.
1. Keep the transmitter out of children’s reach.
2. Do not leave anyone in the vehicle while running on remote control.
3. Alert servicing personnel that the vehicle can be started automatically.
7
4. Do not start the vehicle by remote while it’s in an enclosed area or
garage.
5. Always apply the parking brake and lock the vehicle as you exit the
vehicle.
6. Should the unit malfunction, disconnect the fuse until the problem is
corrected.
7. The use and operations of this system is the sole responsibility of the
operator.
8. Some areas may have local ordinances that prohibit leaving a vehicle
running on public streets.
A. TO REMOTE START THE VEHICLE:
When you want to start your vehicle,
1. Press
button once on the transmitter.
2. The parking lights will flash to indicate the remote start received the
signal.
3. The engine will start approximately 5 seconds.
4. Once the engine is running, after a couple of seconds the parking light
will turn on again and climate controls will activate and adjust the
vehicles interior temperature to your preset setting.
5. The vehicle will run for 5 to 30 minute cycle and automatically shut
down.
(SAFTEY START OPERATION:)
The safety start feature allows you to press the
button Twice before the
vehicle will remote start or remote shut down.
NOTE: The Remote Start Unit will not start the vehicle if any one of the
following conditions exists:
1. The hood is opened.
2. The brake pedal is pressed.
3. Move the optional remote start enable toggle switch to OFF position.
(If installed)
4. The gear selector is in any gear other then “PARK” or “NEUTRAL”
TO TURN OFF THE REMOTE START:
When the engine is running (by remote start), if you want to stop it,
1. Press
button once on the transmitter.
3. Press the brake pedal
The vehicle will shut down and turn off the parking light to indicate engine
stopped.
TO OVERRIDE VEHICLE FROM REMOTE START CONTROL:
8
To operate the vehicle while running from the remote start.
1. Insert the ignition key and turn it to “ON” (not the start) position.
2. Press the brake pedal.
Note: If the brake pedal is pressed before the key is in the ON
position, the engine will shut down.
TEMPORARY STOP FEATURE:
This feature allows the vehicle to remain running after the key has been
removed from the ignition. This feature is useful for occasions when you
wish to exit and lock the vehicle for short periods of time, but would like to
leave the engine running and the climate control on.
1. Before turning off the engine, press the
button once on the
transmitter. The parking lights will come on and the LED will flash 3
times to confirm Temporary Stop feature ‘ON’
2. Turn the ignition key to OFF position. (The engine will stay running.)
3. The engine will run until the pre-programmed time elapsed or shutdown
input is received.
TIMER START:
This unit can be programmed to start and run the engine every 3 hours.
The engine will run for the programmed run time and then shut down.
IMPORTANT: Timer Start should be used only in open areas, Never start
and run the vehicle in on enclosed space as a garage or carport.
3 hours timer start: This feature is design for an extreme cold climate
usage. The system will auto start the vehicle every 3 hours, to prevent
engine freezing and hard to start.
A MAXIMUM OF SIX CYCLES CAN OCCUR.
ENTER:
1. Press the
button once to remote start the vehicle. As soon as the
vehicle is running and the parking lights have turned ‘ON’.
2. Immediately press the
button then press
button once. The
parking light will flash (3) times. The siren chirps (3) times. The vehicle
is now programmed to start every (3) hours.
3. Press the brake pedal to stop the vehicle running.
Exit the timer start:
Timer start can be exited manually as follows:
1. Repeat the Enter Steps from above.
Or
1. Make sure the remote start system is not operating the engine.
2. Turn the ignition on. The LED and parking light will flash (4) times. The
horn chirps (4) times.
SHUT-DOWN INPUT FOR REMOTE STARTER:
If any of the following conditions exist while the system is operating, the
engine will not start or will shut down immediately:
9
1. The hood is opened.
2. The brake pedal is pressed.
3. Move the optional remote start enable toggle switch to OFF position. (If
installed)
4. Engine is over-revved. {“Tachometer checking type” only}
5. The pre-programmed run time (5 /10 / 20 / 30 minutes) has elapsed.
6. Transmitter
button is pressed.
7. The vehicle refused to start running after {3} unsuccessful attempts.
DISABLING THE REMOTE START SYSTEM: (If installed)
This feature allows your system’s remote start unit to be temporarily
disabled to prevent the vehicle from being remote started accidentally. This
feature is useful if the vehicle is being serviced or stored in an enclosed
area. To disable the remote start, move the optional remote start enable
toggle switch to the OFF position.
LIMITED LIFETIME WARRANTY PROVISIONS
( U.S. ,Continental U.S. and Canada Only)
1.
Auto Page, Inc. WARRANTS that this new unit has been thoroughly inspected and
tested at the factory prior to delivery. Your Auto Page equipment is guaranteed for
“life” to the original purchaser/user of the equipment and the original vehicle in which it
was installed by an authorized installer under the following conditions: If the product
proves defective (according to Auto Page's testing) within the first year, the defective
unit may be exchanged or repaired free of charge. “Proof of Purchase” (dated sales
receipt) must accompany all warranty returns; otherwise, your return will be
rejected and sent back. After one (1) year, the purchaser should ship the unit prepaid
to Auto Page with a money order in the amount of $30.00 to cover shipping and
handling charges. Note: The product needs to be registered online at time of
installation. www.autopageusa.com
2.
This WARRANTY will be considered void if the equipment has been misused, neglected,
improperly serviced or installed, altered, dropped or damaged by water, contrary to the
Auto Page OPERATIONS MANUAL. Or, if used with accessories not approved by
Auto Page, which may have contributed to the defect. See note below regarding
product installation**.
3.
The purchaser’s remedies under this WARRANTY shall be limited to the repair or
replacement of electronic components only.
THE FOLLOWING IS NOT
COVERED: Damages or deterioration to cases, batteries, covers and cabinets; the cost
of repairs, replacement and labor of which shall be borne by the purchaser even if
occurring during the WARRANTY period.
10
4.
Any equipment or parts which are claimed to be defective under this WARRANTY must
be sent to the Auto Page Service center with “proof of purchase” at the purchaser’s
expense prior to such return, a Return Authorization Number should be obtained. Auto
Page will return the equipment, charges prepaid. Warranty Service can be provided
through the dealer where the equipment is originally purchased.
5.
Any unexpired WARRANTY shall be applicable to equipment and parts in the
possession of the original purchaser only.
6.
THIS WARRANTY IS IN LIEU OF ANY AND ALL OTHER WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE.
7.
Auto Page shall not be liable, under the foregoing WARRANTIES or otherwise, for:
Any personal injury of any kind to the purchaser, its employees or agents or anyone
else whomsoever resulting directly or indirectly from the use or presence of the
equipment or parts; Consequential damages of any kind; any inability of the purchaser
to use the equipment.
**IMPORTANT NOTE: Any damages to the alarm system resulting from an
installation performed by anyone other than a professional installation
technician authorized by a dealer of Auto Page will void the product’s limited
lifetime warranty.
Auto Page Warranty:
You must register your product online at
http://www.autopageusa.com to receive any warranty service.
Please go to the customer service tab and select product
registration.
OPTIONAL EQUIPMENT:
XT-43 / Antenna Kit: This is an optional package that will enable your
unit to have two-way communications and paging capabilities with the
handheld remote. The optional kit includes a XT-43 LCD remote transceiver
as well as the TRX-76 two-way antenna module. Please see your
authorized Autopage dealer for information and pricing of this option.
It is the purchaser’s responsibility to register this product
11
for any future warranty service.
Warning: Some batteries may contain Perchlorate
What is Perchlorate? Perchlorate is both a naturally occurring and manmade
contaminant increasingly found in groundwater, surface water and soil. Most perchlorate
manufactured in the U.S. is used as an ingredient in solid fuel for rockets and missiles. In
addition, perchlorate-based chemicals are also used in the construction of highway
saf ety flares, fireworks, pyrotechnics, explosives, common batteries, and automobile
restraint systems. Perchlorate contamination has been reported in at least 20 states.
Perchlorate greatly impacts human health by interfering with iodide uptake into the thyroid
gland. In adults, the thyroid gland helps regulate the metabolism by releasing hormones,
while in children; the thyroid helps in proper development. Perchlorate is becoming a
serious threat to human health and water resources.“Perchlorate Material – Special
handling may apply.” For more information, go to
http://www.dtsc.ca.gov/hazardouswaste/perchlorate/
12
960 Knox Street Unit B, Torrance, CA 90502
Tel: (310) 323-1800 or (800) 262-2527
www.autopageusa.com
13