User guide | Autostart AS-1451HF Remote Starter User Manual

AUTOMATIC TRANSMISSION REMOTE STARTER
AS-1727
User Guide
Table of Contents
Table of Contents ................................... 1
Introduction............................................. 2
Using the Remote Control ...................... 2
Multi-Level Features (default state)....... 3
Remote-Starting Your Vehicle ................ 4
Vehicle Presets....................................... 4
Driving Off............................................... 4
Using the Remote Starter ....................... 4
Arming the Starter Kill............................. 4
Idle Mode................................................ 5
Turbo Mode ............................................ 5
Valet Mode.............................................. 5
Valet Mode Using the Valet Switch (if
installed) ................................................. 5
Ignition Valet ........................................... 5
Remote Valet Mode................................ 6
Panic Mode............................................. 6
Quick LockoutTM...................................... 6
Cold Weather Mode................................ 6
Advanced Features: Installationprogrammable Options ........................... 7
Remote Door Locks................................ 7
Priority Door Access ............................... 7
Active or Passive Arming........................ 7
The Starter Kill and the Anti-grind Feature
................................................................ 7
Flashing LED .......................................... 8
Safe Start................................................ 8
Ignition-Controlled Door Locks ............... 8
Ignition Re-lock....................................... 8
Secure Lock............................................ 8
Turbo Mode ............................................ 8
Remote Trunk Release........................... 8
Engine Run Time.................................... 8
Extended Run Time................................ 9
Multi-car Operation ................................. 9
Troubleshooting Poor Transmitting Range
................................................................ 9
Limited Lifetime Warranty…………………….10
INDUSTRY CANADA USER NOTICE:
Operation is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device. To reduce potential radio interference to other users, the antenna type and
its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more
than that required for successful communication".
FCC USER NOTICE (U.S.A.):
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user's
authority to operate the equipment.
DOC: 1.02
– November 1, 2006
TL
Manufactured in Canada
Introduction
This is a state-of-the-art remote starter system. The system is packed with advanced features such
as priority access to the driver’s door (commodity features) and the safe start children safety
feature. With many an advanced function, this product will satisfy any one your expectations from
high-end commodity and security systems, without neglecting any standard feature commonly
offered by entry-level starters.
Using the Remote Control
Your remote starter is equipped with a multi-channel remote control. It can operate two
independent vehicles equipped with an identical remote starter unit. (See Multi-car operation
section on page 9). The functions of the transmitter are as follows:
LOCK Button:
Locks all Doors and
arms the Starter Kill
UNLOCK Button:
Unlocks all Doors and
disarms the Starter Kill
AUX4 - Left Sliding
Door (LSD) Button
AUX5 - Right Sliding
Door (RSD) Button
TRUNK Button:
Activates the Trunk
output (AUX3)
START/STOP Button:
. Starts or Stops the
engine
PANIC/AUX Button:
. Press 3sec will activate Panic Mode (Horn
must be connected)
. This button also serves as a Shift button. In
combination with other buttons allows
assigning different functions to those buttons
• Pressing and holding the LOCK button for more than 3 seconds will lock all doors and will send a
constant pulse as long as the LOCK button is held down (maximum of 15 seconds). This
constant pulse can be configured to activate certain functionalities such as rolling up the
windows – Please refer to your installer to see if your vehicle is compatible with this
option.
• Pressing and holding the UNLOCK button for more than 3 seconds will unlock all doors and will
send a constant pulse as long as the UNLOCK button is held down (maximum of 15 seconds).
This constant pulse can be configured to activate certain functionalities such as rolling down the
P. 2
User Guide
windows – Please refer to your installer to see if your vehicle is compatible with this
option.
Multi-Level Features (default state)
Basic Features (press the PANIC/AUX button 1X)
PANIC/AUX ¾ LOCK .................................................................................. AUX 2
PANIC/AUX ¾ START/STOP ....................................................................... cold weather
Multi-Car Operation (press the PANIC/AUX button 2X)
PANIC/AUX ¾ PANIC/AUX ¾ LOCK:
............................................ 2nd car lock
PANIC/AUX ¾ PANIC/AUX ¾ UNLOCK:
............................................ 2nd car unlock
PANIC/AUX ¾ PANIC/AUX ¾ START/STOP: ............................................ 2nd car start/stop
PANIC/AUX ¾ PANIC/AUX ¾ TRUNK:
............................................ 2nd car trunk
Customized Features (press the PANIC/AUX button 3X)
(May not be applicable for certain vehicles)
Your installer can add customized features such as turning on the radio, opening sliding doors, etc.
PANIC/AUX
PANIC/AUX
PANIC/AUX
PANIC/AUX
¾
¾
¾
¾
PANIC/AUX
PANIC/AUX
PANIC/AUX
PANIC/AUX
¾
¾
¾
¾
PANIC/AUX
PANIC/AUX
PANIC/AUX
PANIC/AUX
......................... ¾ LOCK:
......................... ¾ UNLOCK:
......................... ¾ TRUNK:
......................... ¾ START/STOP:
customized feature 1
customized feature 2
customized feature 3
customized feature 4
By default, the multi-level features are programmed as follows:
x Level 1 (Basic Features)
x Level 2 (Multi car operation)
x Level 3 (Customized Features)
x To access a feature that is programmed as level 1, press the PANIC/AUX button once followed
by the desired function.
x To access a feature that is programmed as level 2, press the PANIC/AUX button twice followed
by the desired function.
x To access a feature that is programmed as level 3, press the PANIC/AUX button three times
followed by the desired function.
Your installer can customize the system as to personalize these multi-level features in an order that
best suits you.
Your options are:
Option 1:
Level 1 (requires pressing the PANIC/AUX button 1X)
Æ
Multi car operation
Æ
Basic features
Level 2 (requires pressing the PANIC/AUX button 2X)
Level 3 (requires pressing the PANIC/AUX button 3X)
Æ
Customized features
Option 2:
Æ
Basic features
Level 1 (requires pressing the PANIC/AUX button 1X)
Level 2 (requires pressing the PANIC/AUX button 2X)
Æ
Multi car operation
Level 3 (requires pressing the PANIC/AUX button 3X)
Æ
Customized features
Option 3:
Æ
Customized features
Level 1 (requires pressing the PANIC/AUX button 1X)
Æ
Multi car operation
Level 2 (requires pressing the PANIC/AUX button 2X)
Level 3 (requires pressing the PANIC/AUX button 3X)
Æ
Basic features
Option 4:
Æ
Level 1 (requires pressing the PANIC/AUX button 1X)
Æ
Level 2 (requires pressing the PANIC/AUX button 2X)
Level 3 (requires pressing the PANIC/AUX button 3X)
Æ
User Guide
Basic features
Customized features
Multi car operation
P. 3
Example: If the multi-level features were set to option 3, the setup would be as follows:
x Level 1 Æ Customized feature
x Level 2 Æ Multi car operation
x Level 3 Æ Basic features
The “Basic features” are now programmed as level 3 and therefore:
x To access cold weather mode, the user needs to press on the PANIC/AUX button three (3) times
followed by the START/STOP button.
Remote-Starting Your Vehicle
Press the START/STOP button for approx. 1 second. The parking lights will come on to inform you
that the remote starter has received your signal. Approximately 5 seconds later, the engine will
start. The parking lights will remain on during the pre-programmed run time of the engine.
If the vehicle does not start at the first attempt, the system will shut down, wait a few seconds and
try to start the engine again. There will be 3 start attempts before the system gives up.
Vehicle Presets
Heater & Heated Seat
When leaving the vehicle it is recommended to preset the accessory controls in preparation for the
next remote start. Settings for the blower motor (fan), front and rear, as well as heated seats (if
equipped) should not be left on HIGH. It is recommended to leave the settings on LOW or MEDIUM
instead.
Windshield Wipers & Radio & Headlights
Certain vehicles require the radio and / or windshield wiper and / or headlight circuits to become
energized while running under remote start. When leaving the vehicle you must ensure that the
windshield wiper and headlight switches are off. Leaving the headlight switch on on certain types of
vehicles could cause them to remain on even after remote starter shut down, resulting in a dead
battery.
Driving Off
With the vehicle running under remote control, press the UNLOCK button to disarm and unlock the
doors. Enter the vehicle and do the following:
Turn the ignition key to the IGNITION ON (RUN) position. (Do not turn the key to the CRANK position
while the engine is running. This would cause the starter motor to re-engage.)
Press the brake pedal to disengage the remote starter unit.
You are now ready to drive off.
Using the Remote Starter
Arming the Starter Kill
The starter kill (if installed) can be configured by the installer so as to arm automatically (passive
mode) or not to arm automatically (active mode). See section passive or active arming on p. 7 for
more details on passive mode and active mode.
• To disarm the starter kill, press the UNLOCK button on the transmitter.
The parking lights will flash twice.
If remote door locks are installed, this will also unlock the doors.
• To arm the Starter Kill, press the LOCK button on the transmitter.
The parking lights will flash once.
If remote door locks are installed, this will also lock the doors.
• In passive mode, the starter kill will automatically arm if the ignition key is not inserted
Into the ignition switch within 1 or 3 minutes after unlocking (the key sense feature
must be installed).
P. 4
User Guide
Idle Mode
Convenience feature: Idle mode allows you to keep the engine running and the doors
locked while you stop, for example, at a convenience store or for a short delivery.
This feature allows you to let the remote starter take over control of the vehicle (i.e. no key in the
ignition switch) while the engine is running. For example, if you stop for a delivery or at a convenience store, lock your vehicle and leave it running for the length of a run cycle while you are away.
To leave the vehicle in idle mode:
1. With the engine running, press the LOCK or UNLOCK button (to unlock the doors) or the
START/STOP button on the remote control until the parking lights come on.
2. Remove the key and exit the vehicle. The engine will go on running.
3. Lock the doors if needed.
The engine will go on running until the user re-enters the vehicle or until the expiration of the
engine run time.
Caution!!! Do not leave children or pets unattended in a vehicle standing in Idle Mode.
Turbo Mode
If turbo mode is configured at installation, it will allow a turbocharger to idle down after the user
leaves the vehicle: the unit will take over the vehicle and keep it running for 60 seconds (or until it
is shut down by remote control), then shut down the engine.
Proceed as follows to set the system to Turbo Mode:
1. With the engine already running, press the LOCK button on the transmitter until the
parking lights come ON.
2. Remove the ignition key from the ignition switch.
The engine will go on running.
3. Exit the vehicle and close the door.
4. Press the TRUNK button to lock the doors.
The engine will shut down after 60 seconds of Turbo Mode.
Valet Mode
Valet Mode Using the Valet Switch (if installed)
When your vehicle is in valet mode, the remote starter functionalities are disabled. If the vehicle
needs to be serviced, or if you park it indoors, the valet mode will prevent the engine from being
remote-started accidentally.
To put the system i n t o valet mode:
1.
Turn the ignition key to the IGNITION ON (RUN) position.
2.
Within 3 sec., press the valet button.é
3.
The parking lights will flash three times to indicate that the vehicle is now in valet
mode. Turn the ignition to the OFF position.
The L.E.D. will come ON solid.
To take the system o u t o f valet mode:
1. Turn the ignition key to the IGNITION ON (RUN) position.
2. Within 3 sec., press and release the valet button.
3. The parking lights will flash twice to indicate that the vehicle is now out of valet mode.
The L.E.D. will go out.
Note: Once valet mode is activated, the remote starter and alarm functions will be disabled.
Ignition Valet
This feature will allow you to remotely put your system into valet mode by using the ignition key
instead of the valet button as above. Ignition valet can be used without a valet button installed.
User Guide
P. 5
To put the system i n t o valet mode:
Insert the ignition key into the ignition switch. Within 10 sec., turn the key 5 times
successively into the IGNITION ON / RUN and OFF positions.
The parking lights will flash three times to indicate that the vehicle is now in valet mode. The
L.E.D. will come ON solid.
To take the system o u t o f valet mode:
Insert the ignition key into the ignition switch. Within 10 sec., turn the key 5 times
successively into the IGNITION ON / RUN and OFF positions.
The parking lights will flash twice to indicate that the vehicle is now out of valet mode. The
L.E.D. will go out.
Note: With the ignition valet activated, the remote starter and alarm functions will be disabled.
Remote Valet Mode
This feature will allow you to remotely put your system into valet mode by using the transmitter
instead of the valet button as above.
Getting into valet mode
• Hold the UNLOCK and START/STOP buttons simultaneously for 3 second.
• The parking lights will flash 3 times.
The LED will remain on solid.
Getting out of valet mode
• Hold the UNLOCK and START/STOP buttons simultaneously for 3 second.
• The parking lights will flash 2 times.
The LED will turn off.
Panic Mode
Note: Panic mode can only be activated if the horn has been adequately configured by your
installer.
In an emergency situation, you can activate panic mode by pressing and holding the PANIC button
for 3 seconds. If the vehicle is under a remote start, you can shutdown the engine, stop the horn by
pressing the LOCK button:
If the car is not running, you can stop the horn by pressing the LOCK or UNLOCK.
Furthermore, the panic mode can be stop by activating one of the following three (3) features:
a) Remote valet (pressing UNLOCK and START/STOP for 3 seconds)
b) Ignition valet (turning the key inside the ignition switch from OFF to ON 5 times in a row)
c) By pressing the valet switch (if included).
Panic Mode will automatically shut down after 30 sec.
Quick LockoutTM
(Also called secure panic.) For fast protection in emergency situations, the system will LOCK all
doors when you press the brake pedal while you hear the sound signal. (Quick lockout is only
available when panic mode has been set off.)
Cold Weather Mode
When cold weather mode is active, the engine starts every 2 hours and runs for 4 minutes (or for 9
or 20 minutes with diesel engines). Cold weather mode automatically ends after 24 hours.
To enter Cold Weather Mode:
•
Press the PANIC button and then the START/STOP for 3 seconds.
•
The parking lights will flash three (3) times.
To exit Cold Weather Mode, do any one of the following actions:
•
Open the hood.
•
Start the engine by remote.
P. 6
User Guide
•
•
Turn the ignition key to the IGNITION ON (RUN) position.
Press the PANIC/AUX button and then the START/STOP button for three seconds (the
parking lights will flash once).
To verify whether the system is in cold weather mode:
Press and release the brake pedal:
If the vehicle is in cold weather mode, the parking lights will stay on while the pedal is
pressed.
Advanced Features: Installation-programmable Options
The remote starter was designed with flexibility and OEM integration in mind. With its programmable options, this unit can single-handedly control nearly any electrical system in your vehicle.
Caution: The programming of your system should be left to a professional. Changing any
one of the settings may affect the operation of your remote starter.
The installation-programmable options are as follows:
Remote Door Locks
Priority Door Access
Passive or Active Arming
Starter Kill / Anti-grind feature
Horn Chirp Timing
Safe Start
Ignition-controlled Door Locks
Ignition Re-lock
Secure Lock
Turbo Mode
Remote Trunk Release
Engine Run Time
Extended run time
Multi-car Operation
Remote Door Locks
If your remote starter was installed with the remote door locks option, you will have the
convenience of remote keyless entry. See section Arming and Disarming the Remote Starter,
on page 4, for further instructions on remote door locking and unlocking.
Priority Door Access
If the remote door locks option is installed on your vehicle, this safety feature allows you unlock
solely the driver’s door with a single press of the UNLOCK button on the transmitter; upon a second
press of the UNLOCK button, all the other doors will unlock.
Active or Passive Arming
The starter kill can be configured either to passive mode (so as to arm automatically) or active
mode (so as to require user intervention for arming). By default, your remote starter is configured to
passive mode. In passive mode, the starter kill will automatically arm 60 seconds after the last
door is closed. The remote starter will not arm if a door is left open, or if you re-open a door within
the 60-second delay.
Important note: When the remote starter re-arms automatically, you can disarm the When
the remote starter by simply pressing the UNLOCK button.
The Starter Kill and the Anti-grind Feature
With this added security feature, the system will prevent your vehicle from starting with the ignition
key when the starter kill is armed. If your remote starter was installed with the starter kill option,
one will not be able to start your vehicle with the key unless the system has been unlocked and
disarmed first, or put into valet mode.
Note: If the starter kill is installed, your vehicle will benefit from a protection against starter
motor damage that could occur after remote-starting the engine should the user, by force of
habit, turn the ignition key to the CRANK position.
User Guide
P. 7
Flashing LED
The user may decide to turn on or off LED flashing at any moment. To do so, simultaneously press
and hold the LOCK and UNLOCK buttons on the transmitter. Keep holding the buttons until the
parking lights flash three (3) times. At that point release the buttons. The LED will toggle to its next
state –i.e.: ON/OFF:
There are three programmable options regarding the flashing LED:
i. The LED flashes once the starter kill is activated (passive or active arming) and will turn itself
off once the user turns the key to the IGNITION ON position.
ii. The LED is totally disabled and will not flash –it will turn on solid however when in valet
mode.
iii. The LED will flash once the starter kill is activated but requires pressing the UNLOCK button to
turn itself off. Failure to press the UNLOCK button will make the LED flash even if the key is in
the IGNITION ON position.
Safe Start
If this feature is enabled, the user must press the START/STOP button 2 times within 3 seconds to
remote-start the vehicle. This will eliminate accidental remote starts, e.g. when children are playing
with the transmitter.
If swap start mode is selected, to remote-start your vehicle, press the PANIC/AUX button and then
the LOCK button. The AUX 2 output can be activated by pressing the START/STOP button.
Ignition-Controlled Door Locks
This is an added security feature. If your remote starter was installed with the ignition-controlled
door locks option, the doors will automatically be locked as soon as the ignition key is turned to the
IGNITION ON (RUN) position while the brakes are pressed. When the key is turned to the OFF position,
the doors will automatically be unlocked.
Ignition Re-lock
On remote starters of this series, when ignition-controlled door locks are enabled and the ignition
key is in the IGNITION ON (RUN) position, should any door be unlocked and opened, all doors will be
relocked next time the brake pedal is pressed.
Secure Lock
Before it can remote-start your vehicle, the remote starter must first disarm the factory security
system. The secure lock feature may be required on certain vehicle models with factory security
systems that automatically unlock the doors when the security system is disarmed.
To keep your vehicle protected when the factory security system is disarmed for a remote start,
secure lock will relock your doors as soon as the vehicle has started. Once the engine run cycle
ends, secure lock will rearm your factory security system.
Turbo Mode
When left in turbo mode, the remote starter will keep the engine running for 60 seconds before
shutting it down. This is to allow a turbocharger to idle down after the user leaves the vehicle. See
Turbo Mode section on page 5.
Remote Trunk Release
If your system was installed with the remote trunk release option, you can open your trunk by
pressing the TRUNK button.
Engine Run Time
If you have a gas engine, your remote starter can be programmed to run the engine for 4, 15, or
25 minutes (15 minutes by default). If you have a diesel engine, the remote starter can be
programmed to run the engine for 9, 20, or 30 minutes (20 minutes default).
P. 8
User Guide
Extended Run Time
While the vehicle is running under a remote start, pressing and holding the START/STOP button
for more than 3 seconds will reset the run time counter to zero and restart the run time cycle from
the beginning. The parking lights will flash three times and the horn (if configured) will honk once.
The extended run time procedure can only be carried out once per remote start.
To stop the vehicle, at any moment, simply press the START/STOP button.
Example: If your remote car starter is programmed for a run time of 4 minutes and your vehicle
has been running for 3 minutes already, pressing the START/STOP button will reset the
counter to zero and allow the engine to run for another cycle (in this case, 4 minutes).
Multi-car Operation
This option allows the owner of two vehicles, both equipped with the same remote starter model, to
control both systems with a single remote control. To control the second vehicle:
Note: Your remote control must be configured for second car operation by the installer.
Press TRUNK + LOCK buttons simultaneously:......................... LOCK
Press TRUNK + UNLOCK simultaneously:.................................. UNLOCK
Press TRUNK + START/STOP simultaneously: ....................................START
Press TRUNK + START/STOP simultaneously: ............................ STOP
Press SHIFT ¾ SHIFT ¾ TRUNK: ................................................ TRUNK
Or
Press PANIC/AUX
Press PANIC/AUX
Press PANIC/AUX
Press PANIC/AUX
Press PANIC/AUX
¾ PANIC/AUX
¾ PANIC/AUX
¾ PANIC/AUX
¾ PANIC/AUX
¾ PANIC/AUX
¾ + LOCK: ............................. LOCK
¾ + UNLOCK:......................... UNLOCK
¾ + START/STOP: .........................START
¾ + START/STOP: ................... STOP
¾ + TRUNK: ........................... TRUNK
Troubleshooting Poor Transmitting Range
Many factors may affect the operating range of the transmitter. Some of these are:
The condition of the battery in the transmitter.
The operating environment (for example: downtown radio-frequency noise, airports, cellular phone
towers…)
Metal: any type of metal will affect operating range. This includes the metal in the car.
The shape of the vehicle can affect range as well; vans in general have an especially poor range.
The shape of the roof and A-pillars brings about considerable radio-frequency deflection (in this
case the signal from the remote control). As a result, the direction in which the vehicle is facing in
relation to the remote control can affect the range. Straight on – standing in front of the vehicle –
generally gives you the greatest range; the second best performance is from the back. Using the
remote control from either side of the vehicle will usually give the lowest range.
The range will be significantly lower in a crowded parking lot than in open space.
Always hold the transmitter high, approximately at shoulder height. Holding the transmitter against
your chin will also increase your range: your head acts as an antenna.
The operating range will be somewhat lower on vehicles equipped with an aftermarket or factory
alarm.
User Guide
P. 9
LIMITED LIFETIME WARRANTY
REMOTE STARTERS:
As the manufacturer, 160031 Canada Inc. (“Autostart”) warrants to the original consumer purchaser only
(nontransferable) that the remote starter module (control box) shall be free from defects in materials and
workmanship for as long as the original consumer purchaser continuously owns the vehicle in
which the remote starter was originally installed, as specified below:
1)
For the first year after the date of manufacture, as specified by the serial number on the
module, Autostart will replace the remote starter module free of charge with a new remote
starter module.
2)
For the second year after the date of manufacture, as specified by the serial number on the
module, Autostart will replace the remote starter module free of charge with a repaired or
refurbished remote starter module.
3)
For the third year and any consecutive year after the date of manufacture, as specified by the
serial number on the module, Autostart will provide to the original consumer purchaser a
repaired or refurbished remote starter module, for a repair charge of $35.00 plus applicable
taxes.
In all cases, the consumer must return the remote starter module to the point of purchase, and must
provide a copy of the proof of purchase to said retailer. A remote starter module will be returned to the
retailer for the consumer to claim within a 4 (four)-week period. For case (3), a cheque in the amount of
$35.00 plus applicable taxes must accompany the remote starter module, or the retailer may refuse the
return.
ACCESSORIES:
Autostart warrants to the original consumer purchaser only (nontransferable) that it will replace any
Autostart accessory part for a one-year period from date of purchase. Accessories will only be replaced if
proven defective in material or workmanship, and if, when the accessory is returned to the point of
purchase, the retailer is provided with a copy of the proof of purchase. The accessory will be sent to the
retailer for the consumer to claim within a 4 (four)-week period.
THE WARRANTY IS VOID IF:
1)
The product has been damaged, altered in any way or tampered with, without the
explicit written consent of an Autostart technician. For remote starter modules,
this includes the opening or removal of the plastic covering of the module, or the
removal or alteration of the barcode label on the plastic covering of the module.
2)
The product is damaged due to accident, fire, flood, shipping and handling,
misuse, neglect, or other conditions beyond the control of Autostart.
3)
The product has been installed or repaired by anyone other than a certified
technician.
4)
The product has been improperly installed or used.
THE WARRANTY DOES NOT COVER:
1)
Batteries.
2)
Scratched or worn transmitter cases.
3)
Installation and/or removal charges for all remote starter modules and
accessories.
4)
Shipping and handling charges incurred for product exchange or replacement.
5)
Any material damages other than to the product itself.
6)
Harnessing, L.E.D. lights, switches, inverters, relays, etc.
THIS LIMITED LIFETIME WARRANTY SHALL CONSTITUTE THE SOLE LIABILITY OF AUTOSTART FOR OUR PRODUCTS,
AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED. THERE ARE NO WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. NO PERSON, FIRM OR CORPORATION IS
AUTHORIZED TO ASSUME FOR AUTOSTART ANY OTHER LIABILITY WITH RESPECT TO THE SALE OR USE OF OUR
PRODUCTS. AUTOSTART’S LIABILITY, WHETHER BASED ON CONTRACT, TORT, WARRANTY, STRICT LIABILITY, OR ANY
OTHER THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT FOR DAMAGE IS THE
BASIS OF THE CLAIM. UNDER NO CIRCUMSTANCE WILL AUTOSTART, ITS DISTRIBUTORS OR THEIR AGENTS BEAR ANY
LIABILITY WHATSOEVER FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
The parties hereto elect that any dispute regarding the present document be submitted to the appropriate Court located in the
Province of Quebec, District of Montreal. The parties hereto agree that this document is governed by and interpreted in accordance
with the law of Quebec. If the purchaser is located in a province of Canada other than Quebec, all matters dealing with the warranty
of quality will be governed by and interpreted in accordance with the law of Ontario. If the purchaser is located outside Canada, all
matters dealing with the warranty of quality will be governed by and interpreted in accordance with the United Nations Convention
on Contracts for the International Sale of Goods (the “Vienna Convention”).
P. 10
User Guide
Download PDF

advertising