Avaya 15-601078 IP Phone User Manual

IP Office
2420/5420 Phone User Guide
15-601127 Issue 09a - (16 July 2009)
© 2009 AVAYA All Rights Reserved.
Notice
While reasonable efforts were made to ensure that the information in this document was complete and accurate at the time of
printing, Avaya Inc. can assume no liability for any errors. Changes and corrections to the information in this document may be
incorporated in future releases.
Documentation Disclaimer
Avaya Inc. is not responsible for any modifications, additions, or deletions to the original published version of this
documentation unless such modifications, additions, or deletions were performed by Avaya.
Link Disclaimer
Avaya Inc. is not responsible for the contents or reliability of any linked Web sites referenced elsewhere within this
Documentation, and Avaya does not necessarily endorse the products, services, or information described or offered within
them. We cannot guarantee that these links will work all of the time and we have no control over the availability of the linked
pages.
License
USE OR INSTALLATION OF THE PRODUCT INDICATES THE END USER’S ACCEPTANCE OF THE TERMS SET FORTH
HEREIN AND THE GENERAL LICENSE TERMS AVAILABLE ON THE AVAYA WEBSITE AT
http://support.avaya.com/LicenseInfo/ (“GENERAL LICENSE TERMS”). IF YOU DO NOT WISH TO BE BOUND BY THESE
TERMS, YOU MUST RETURN THE PRODUCT(S) TO THE POINT OF PURCHASE WITHIN TEN (10) DAYS OF DELIVERY
FOR A REFUND OR CREDIT.
Avaya grants End User a license within the scope of the license types described below. The applicable number of licenses and
units of capacity for which the license is granted will be one (1), unless a different number of licenses or units of capacity is
specified in the Documentation or other materials available to End User. “Designated Processor” means a single stand-alone
computing device. “Server” means a Designated Processor that hosts a software application to be accessed by multiple users.
“Software” means the computer programs in object code, originally licensed by Avaya and ultimately utilized by End User,
whether as stand-alone Products or pre-installed on Hardware. “Hardware” means the standard hardware Products, originally
sold by Avaya and ultimately utilized by End User.
License Type(s): Designated System(s) License (DS).
End User may install and use each copy of the Software on only one Designated Processor, unless a different number of
Designated Processors is indicated in the Documentation or other materials available to End User. Avaya may require the
Designated Processor(s) to be identified by type, serial number, feature key, location or other specific designation, or to be
provided by End User to Avaya through electronic means established by Avaya specifically for this purpose.
Copyright
Except where expressly stated otherwise, the Product is protected by copyright and other laws respecting proprietary rights.
Unauthorized reproduction, transfer, and or use can be a criminal, as well as a civil, offense under the applicable law.
Third-Party Components
Certain software programs or portions thereof included in the Product may contain software distributed under third party
agreements (“Third Party Components”), which may contain terms that expand or limit rights to use certain portions of the
Product (“Third Party Terms”). Information identifying Third Party Components and the Third Party Terms that apply to them is
available on Avaya’s web site at: http://support.avaya.com/ThirdPartyLicense/
Avaya Fraud Intervention
If you suspect that you are being victimized by toll fraud and you need technical assistance or support, call Technical Service
Center Toll Fraud Intervention Hotline at +1-800-643-2353 for the United States and Canada. Suspected security
vulnerabilities with Avaya Products should be reported to Avaya by sending mail to: securityalerts@avaya.com.
For additional support telephone numbers, see the Avaya Support web site (http://www.avaya.com/support).
Trademarks
Avaya and the Avaya logo are registered trademarks of Avaya Inc. in the United States of America and other jurisdictions.
Unless otherwise provided in this document, marks identified by “®,” “™” and “SM” are registered marks, trademarks and
service marks, respectively, of Avaya Inc. All other trademarks are the property of their respective owners.
Documentation information
For the most current versions of documentation, go to the Avaya Support web site (http://www.avaya.com/support) or the IP
Office Knowledge Base (http://marketingtools.avaya.com/knowledgebase/).
Avaya Support
Avaya provides a telephone number for you to use to report problems or to ask questions about your contact center. The
support telephone number is 1 800 628 2888 in the United States. For additional support telephone numbers, see the Avaya
Web site: http://www.avaya.com/support.
2420/5420 Phone
IP Office
Page 2
15-601127 Issue 09a (16 July 2009)
Contents
Contents
7. Function Keys
1. The Telephone
1.1 Call Appearance
.....................................................................
Keys
8
.....................................................................
9
1.2 Call Appearance
Key Icons
1.3 System Features
..................................................................... 9
1.4 Logging Off..................................................................... 10
1.5 Logging On..................................................................... 10
1.6 No User ..................................................................... 11
1.7 The Display..................................................................... 11
2. Basic Call Handling Features
2.1 Answering .....................................................................
a Call
2.2 Making a Call
.....................................................................
2.3 Clearing a .....................................................................
Call
2.4 Conference.....................................................................
2.5 Transfer .....................................................................
2.6 Headset Working
.....................................................................
2.7 Speakerphone
.....................................................................
2.8 Speed Dial.....................................................................
2.9 Redial
.....................................................................
2.10 Mute
.....................................................................
2.11 Hold
.....................................................................
2.12 Message .....................................................................
2.13 Private Call
.....................................................................
14
15
15
16
16
17
18
19
19
20
20
21
21
7.1 Overview of.....................................................................
the Function Keys
7.2 Display Mode
.....................................................................
7.3 Function Key
.....................................................................
Programming
7.4 Shorthand .....................................................................
Programming Mode
.....................................................................
7.5 Longhand Programming
7.6 Changing Function
Key Labels
.....................................................................
48
49
50
52
53
54
8. System Features
8.1 Introduction.....................................................................
8.2 Ring Back .....................................................................
8.3 Call Forwarding
.....................................................................
.....................................................................
8.4 Diverting Calls
8.5 Do Not Disturb
.....................................................................
8.6 Parking Calls
.....................................................................
8.7 Voicemail .....................................................................
.....................................................................
8.8 Default Feature
Codes
56
56
56
57
58
58
59
60
9. EU24 Expansion Module
9.1 EU24 Overview
..................................................................... 62
9.2 Connection..................................................................... 63
9.3 Using the EU24
.....................................................................
Expansion Module
63
Index
...............................................................................65
3. Using Speed Dials
3.1 Adding a New
.....................................................................
Speed Dial
.....................................................................
3.2 Dialling a Speed
Dial Number
3.3 Deleting a .....................................................................
Speed Dial
3.4 Editing a Speed
Dial
.....................................................................
3.5 Converting.....................................................................
a Call Log Entry to a Speed Dial
25
26
26
26
26
4. Using Visual Voice
4.1 Listen to Voicemails
.....................................................................
.....................................................................
4.2 Send a Voicemail
4.3 Changing Your
Greeting
.....................................................................
4.4 Changing Your
.....................................................................
Mailbox Password
4.5 Email Alerts
.....................................................................
.....................................................................
4.6 Voicemail Transfer
29
30
31
32
33
33
5. Using the Call Log
5.1 Setting Which
Calls are Logged
.....................................................................
5.2 Viewing the.....................................................................
Call Log
5.3 Making Calls
.....................................................................
from the Call Log
5.4 Saving a Call
.....................................................................
Log Entry to Your Speed Dial List
5.5 Deleting a .....................................................................
Call Log Entry
5.6 Erasing All.....................................................................
Logged Calls
37
37
38
38
39
39
6. Changing Options
6.1 Ring Options
.....................................................................
6.2 Adjusting the
.....................................................................
Display Contrast
6.3 Call Log Setup
.....................................................................
6.4 Miscellaneous
.....................................................................
6.5 Using Self .....................................................................
Test
6.6 Default Phone/Erase
.....................................................................
All Settings
6.7 Language .....................................................................
6.8 Automatic Gain
.....................................................................
Control (AGC)
2420/5420 Phone
IP Office
42
43
43
43
44
44
45
45
Page 3
15-601127 Issue 09a (16 July 2009)
Chapter 1.
The Telephone
2420/5420 Phone
IP Office
Page 5
15-601127 Issue 09a (16 July 2009)
The Telephone:
1. The Telephone
This guide covers the use of the 2420 and 5420 phones on IP Office. Both phones are similar, however the 5420 is only
supported on the IP Office whereas the 2420 is supported on a range of Avaya phone systems.
1.
Display, Call Appearance and Feature Buttons: Call Appearance keys enable you to handle multiple calls and the
display shows call information. Details on system features (allocated by your system administrator) can also be
displayed. See Call Appearance Keys 8 and Overview of the Function Keys 48 .
2.
Message Lamp: The lamp is used as follows:
3.
·
On (Continuous): There are new messages in your voicemail mailbox, or another mailbox for which you have
been configured to receive "Message Waiting Indication".
·
Flashing: The lamp can also be set to flash when the phone receives a call. See Ring Options
MESSAGES: Access your mailbox.
Call Handling Buttons:
·
HOLD: Red button used to place a call on hold.
·
TRANSFER: Transfers a call to another phone.
·
CONFERENCE: Sets up conference calls with more than one other person.
·
DROP: Drops the current call or, if on a conference call, drops the last person to join the conference.
·
6.
.
Previous/Next Page: Move through the different pages of the call handling, speed dials and call log screens.
Also used to move the cursor during data entry.
4.
5.
42
REDIAL: Redials the last number dialed or displays the last 6 numbers dialed from the phone, depending
on configuration via the Options menu.
Dial Pad: Standard 12-button pad for dialling phone numbers.
Volume Controls: Adjust the speaker, handset, headset, or ringer volume depending on which is currently in
7.
use.
8.
MUTE: Turns the microphone on/off. When in use, the associated light is on and the caller cannot hear you.
9.
HEADSET: Switches from handset to headset. The light associated with this button turns on when the headset is
active.
10.
SPEAKER: Access the speakerphone. The light associated with this button turns on when the speakerphone is
active. The handset is muted while the speaker or headset is in use.
11.
EXIT: Returns you to the main call handling screen.
12. Softkeys
: Used to navigate to or initiate certain features, such as Speed Dial or Call Log, as well as control
certain actions within the features. These keys correspond to the text prompts in the display screen immediately
above them.
2420/5420 Phone
IP Office
Page 7
15-601127 Issue 09a (16 July 2009)
1.1 Call Appearance Keys
Normally, the first page of the main call handling screen contains three keys set as 'call appearance' keys. These are
allocated to you by your system administrator and are indicated as a=, b= and c=. An underscored call appearance key
(e.g. a=) indicates that the line is active.
Your system administrator can allocate a call appearance key with:
·
A Bridged Appearance
A bridged appearance key matches the status and operation of the call appearance key on a pre-defined colleague’s
phone. Hence, you can pick-up, make and receive calls on behalf of your colleague.
·
A Line Appearance
An IP Office exchange line (but not IP lines) can be allocated to you such that the status of that line is displayed and
you can use the line appearance key to make and receive calls.
·
Call Coverage Appearance
A call coverage appearance key alerts you when a pre-defined colleague is receiving a call. The covered user does
not need to be using call appearance keys. Hence, you can pick-up calls on behalf of your colleague.
For details of Bridged, Line and Call Coverage Appearance keys set-up and their operation, refer the IP Office Key and
Lamp Operation manual.
Having more than two call appearance keys is very useful. When holding a call, you can answer or make another call and
then switch between calls, transfer or conference. If you are set to receive call waiting indication, the waiting call is
shown against the next call appearance key.
Caution
·
Although the system administrator can replace the call appearance keys with Bridged, Line and Call Coverage
Appearance keys, this would severely restrict the use of features such as conference and transfer.
It is for this reason that it is strongly recommended that all call appearance keys remain at their default
settings.
2420/5420 Phone
IP Office
Page 8
15-601127 Issue 09a (16 July 2009)
The Telephone: Call Appearance Keys
1.2 Call Appearance Key Icons
The icons displayed against the Call Appearance/Feature keys, allow you to determine the status (for example, on
HOLD) of each call. Icons also indicate whether a feature has been activated for a particular button.
·
Incoming Call:
A symbol next to a call appearance key indicates an incoming call.
·
Connected:
A symbol next to a call appearance key indicates that it is the currently connected call. The caller's phone number
(if available) is also shown. To put the call on hold, press
HOLD. An H is displayed.
·
On HOLD:
A
symbol next to a call appearance key indicates a call on hold. To take the call off hold and put any other
current call on hold, press
.
·
Function Active:
The button to the left or right of the function key is active.
1.3 System Features
System Features can only be set against soft Function Keys by your system administrator. However, your system
administrator may allocate you two ‘self administrator’ features that will enable you to add System Features to your soft
Function Keys.
In addition, there are a number of System Features that you can always access yourself by the use of short codes.
Refer to System Features Introduction 56 for details of System Features that you can always access yourself by dialling
short codes. For example, to listen to your voicemail messages, dial *17.
2420/5420 Phone
IP Office
Page 9
15-601127 Issue 09a (16 July 2009)
1.4 Logging Off
If you have been allocated a login code, you can log your phone off to prevent unauthorized use during an absence, or
for privacy purposes.
If you are logging off from another extension, the system will log you back in at your home extension, unless the forcelogin option is set.
Caution
·
Call Log entries and certain Speed Dial settings will remain on the extension even when you are logged out.
To log off the phone where you had logged on dial *36.
1.5 Logging On
Your administrator has created your initial configuration so that you will be automatically logged on to your home
extension. However, you may be required to log in for the following reasons:
·
Forced login - if your configuration does not allow automatic login to your home extension.
·
To use an extension other than your own (hot desking)
·
If you, or somebody else, has logged you out of your extension.
Notes
·
When hot desking, any short codes you have setup on your home extension will be passed to the extension you have
logged on to.
·
Certain information such as speed-dials and call log are telephone model dependent, and will not be passed to the
new extension.
·
You will be able to hot desk to extensions on remote sites only if the Small Community Advanced Networking License
is installed on that system.
To login to your home extension (forced login), enter *35*P#, where 'P' is your login code.
To login at another extension (hot desking), enter *35*N*P#, where 'N' is your home extension number and 'P' is
your login code.
Notes
·
Your login code, if configured, will be supplied by your Administrator.
·
You have 4 attempts at logging on. If you fail to logon correctly, the message "Invalid" will be shown on the main
display and you will hear the busy tone. If you fail all 4 attempts to log on, you must wait 90 seconds before any
login will be accepted, whether correct or not.
2420/5420 Phone
IP Office
Page 10
15-601127 Issue 09a (16 July 2009)
The Telephone: Logging On
1.6 No User
The NoUser configuration will be used for extensions where the home user is not currently logged on for example:
·
The home user is logged on to another extension
·
Forced login is enabled
An extension set as NoUser will display the name "NoUser" and the extension number.
If required, and you have been allocated a login code, you can logon using your extension number and login code. (see
Logging On 10 )
Note
·
Although internal calls may be made from an extension marked NoUser, normally calls cannot be received on that
extension.
1.7 The Display
B
Phone Locked:
Internal calls only.
D
Call Forwarding On:
See Call Forwarding 56 .
G
In Group:
You can enable/disable group membership.
H
Held Call:
Shows the number of held calls. See HOLD
N
NoUser
20
.
Do Not Disturb On:
See Do Not Disturb 58 .
No User:
The extension is not currently logged on. see No User
11
O
Out of Hours:
This is displayed if one or more Hunt Groups is in "Out-of-Hours" mode.
P
Parked Calls:
Shows the number of parked calls.
T
Twinned:
The phone is being used as the twin of another phone.
DISC
Disconnected:
To end the call, press
CONN
ssss
CONF
SPEAKER.
Connected:
You are on a call.
Suppressed Code
When an account or authorization code is entered, the number you enter is displayed as "ssss" for security
purposes.
CONFERENCE Call:
You are part of a conference call, displayed on the left hand side of the display. See CONFERENCE Calls
2420/5420 Phone
IP Office
16
.
Page 11
15-601127 Issue 09a (16 July 2009)
Chapter 2.
Basic Call Handling Features
2420/5420 Phone
IP Office
Page 13
15-601127 Issue 09a (16 July 2009)
2. Basic Call Handling Features
2.1 Answering a Call
When a call arrives at your phone, you hear a ringing tone and a blinking bell icon appears on the associated call
appearance.
To answer an incoming call:
Do one of the following:
·
If you are not active on another call, answer the call using your handset, headset or speakerphone (see
Speakerphone 18 ).
·
If you are active on a call already, place the active call on hold (see Hold
·
If the call appearance for the ringing call is not displayed on the current screen page, press
EXIT to return to
the first page of the Home screen. When you locate the call appearance for the ringing call, press the corresponding
call appearance button.
·
If you are a member of a hunt group, you will see a blinking bell icon next to your group name, for example "Sales
". Press
Sales to answer the call.
20
), and then answer the incoming call.
Note
·
To redirect an incoming call, do not answer, press
voicemail (if available).
DROP to redirect the call to Forward On No Answer (if set) or
To answer a call at another extension:
You can answer from your own phone by using Call Pick-Up; lift your handset and dial:
·
*30 to answer a call ringing anywhere.
·
*31 to answer a call within your group.
·
*32*201# to answer the call for a particular extension, in this example 201.
The default ring cadences are:
·
Internal calls - single ring cadence.
·
External calls - double ring cadence.
These can be changed by your system administrator.
Note
·
If your phone rings for any longer than a specified period (15 seconds in default), any re-direction feature that you
have activated, such as voicemail or call forwarding, will come into effect.
2420/5420 Phone
IP Office
Page 14
15-601127 Issue 09a (16 July 2009)
Basic Call Handling Features: Answering a Call
2.2 Making a Call
You can make calls from the phone using a variety of methods as follows:
To manually make a call:
1.
Lift the handset and dial the required number on the key pad. Remember to include the required access code (for
example; 9 for an outside line) and listen to the progress of the call.
2.
Adjust the speakerphone volume as necessary.
To change the volume, press
and
. The eight volume levels are displayed.
3.
If the call is not answered, press
SPEAKER or
DROP.
If the call is answered, either speak or pick up the handset and speak to the called party.
To automatically make a call:
Do any of the following:
·
To have the phone dial the last number that you dialed, press
associated with the call. See Redial 19 .
REDIAL and then press the function key
·
Access the Call Log and initiate a call to a specific entry. See Making Calls from the Call Log
38
.
Access the Speed Dial List in your personal directory and initiate a call to a specific entry. See Dialling a Speed Dial
Number 26 .
When the call is answered, either speak or pick up the handset and speak to the called party.
·
2.3 Clearing a Call
To clear an established call:
Either:
·
or
Replace the handset.
·
Press
DROP.
2420/5420 Phone
IP Office
Page 15
15-601127 Issue 09a (16 July 2009)
2.4 Conference
The Conference feature allows you to conference other parties (including yourself) into a call.
Notes
·
The number of parties allowed in a conference is controlled by your phone system.
·
Two Call Appearance keys are required for the conference feature.
To add another party to a call:
1.
Press
2.
Dial the number of the person you want to add to the call.
3.
CONFERENCE again.
To add the person to the call, press
If the called party does not answer or does not want to join the conference, press
call, press
adjacent to the held call.
4.
CONFERENCE.
DROP. To return to the held
Repeat steps 1 through 5 for additional conference connections.
To see the details of the different participants in the conference, press
and
Prev/Next.
Notes
·
To leave a conference call, hang up.
·
DROP. You can then select the
To display which conference participants to drop from the conference, press
participant to drop by pressing the
and
Prev/Next buttons to display the participant, then press
DROP
again.
2.5 Transfer
This feature allows you to transfer a call from your phone to another extension or outside number.
1. With a call in progress, press
TRANSFER.
2. When you hear dial tone, dial the number to which the call is to be transferred. Then do one of the following:
· To transfer the call without announcing it (an unsupervised transfer), press
transfer is complete.
TRANSFER again. The
· To announce the call before transferring it (a supervised transfer), wait for the called party to answer:
· If the called party is willing to accept the call, press
TRANSFER again to complete the transfer.
· If the called party does not wish to accept the call or there is no answer, press
the held call, press
adjacent to it.
2420/5420 Phone
IP Office
DROP. To return to
Page 16
15-601127 Issue 09a (16 July 2009)
Basic Call Handling Features: Transfer
2.6 Headset Working
When a headset is to be used, it must be plugged in to the headset socket on the base of the phone. To activate the
headset and switch off the handset, press
HEADSET. The lamp beside the button is illuminated when headset
working is activated.
To answer an incoming call:
1.
Press
HEADSET.
If you are already on a call:
·
Place the first call on hold
·
Press
next to the flashing bell icon ( ).
To clear a headset call:
·
Press
DROP.
To manually make a call:
·
Press
HEADSET.
·
Dial the number. Remember to include the required access code (for example; 9 for an outside line) and listen to the
progress of the call.
To automatically make a call:
·
Press
HEADSET.
Do any of the following:
·
Press
REDIAL and then press
to have the phone dial the last number that you dialed. See Redial
·
Access the Call Log and initiate a call to a specific entry. See Making Calls from the Call Log
38
19
.
.
Access the Speed Dial List in your personal directory and initiate a call to a specific entry. See Dialling a Speed Dial
Number 26 .
When the call is answered, speak to the called party.
·
2420/5420 Phone
IP Office
Page 17
15-601127 Issue 09a (16 July 2009)
2.7 Speakerphone
The two-way built-in speakerphone allows you to make and answer calls without lifting your handset. Keep in mind that
two-way speakerphones may not operate satisfactorily in every environment (such as in very noisy locations).
·
For IP Office 4.1 and higher, the Group Listen function can be used to hear a call via the speaker but talk through the
handset. Consult your System Administrator for more details.
To make or answer a call without lifting the handset, or to use the speakerphone with any feature:
1.
Press
SPEAKER. The LED beside the button illuminates.
2.
Make or answer the call, or access the selected feature.
Adjust the speakerphone volume if necessary. To change the volume, press
displayed.
and
. The eight volume levels are
To change from the speakerphone to the handset (or headset if fitted):
·
Pick up the handset (or press
HEADSET) and talk.
To change from the handset to the speakerphone:
·
Press
SPEAKER and hang up the handset.
To end a speakerphone call:
·
Press
SPEAKER again.
2420/5420 Phone
IP Office
Page 18
15-601127 Issue 09a (16 July 2009)
Basic Call Handling Features: Speakerphone
2.8 Speed Dial
The Speed Dial feature enables you to automatically dial calls to phone numbers stored in your personal directory. For
more information about the Speed Dial facility, see Using Speed Dials.
To make a call to a personal directory entry using the Speed Dial feature:
1.
From the Home screen, press any
Soft Key.
2.
From the Home screen, press
3.
Press the button next to the entry you want to call.
SpDial. The Speed Dial screen is displayed.
Note
·
If the entry you want is not displayed, press
and
to search through the entries or key the first letter of the
required name to jump to the page with a matching entry.
The phone dials the number for you.
2.9 Redial
The Redial feature automatically redials a previously dialed extension or outside number (up to 24 digits). Your phone will
store up to ten of the last numbers dialed.
Note
·
If you have dialed the same number twice in succession, it will only have one appearance in the redial list.
To redial a previously dialed number:
·
REDIAL and then press
and
to search through the entries. When you have located the required
Press
number, press the associated
button next to the number.
To redial the last number dialed:
·
Press
REDIAL twice.
2420/5420 Phone
IP Office
Page 19
15-601127 Issue 09a (16 July 2009)
2.10 Mute
During an active call, the Mute feature prevents the party (with whom you are speaking) from hearing you. This feature
is most commonly used in conjunction with the Speakerphone. However, it can be used to hold an off-line conversation at
any time during a call.
To prevent the other person on the line from hearing you:
1.
Press
MUTE. The indicator next to the Mute button lights when Mute is active.
2.
To reinstate two-way conversation, press
MUTE again.
2.11 Hold
You can put a call on hold to gather information, or to answer a second call. If a second call arrives you will here a short
ring and the flashing
symbol will appear next to the Call Appearance key.
To put an existing call on hold:
HOLD.
1.
Press
2.
Answer the second call by pressing the call appearance button with the
; showing that the line is connected.
symbol against it. The symbol changes to
To return to the held call:
1.
If you have a call in progress, then first put that call on hold as above.
2.
To retrieve a held call, press the Call Appearance button with
against it.
Notes
·
With hold return timer (defined by your system administrator), you are reminded that you have a call on hold. The
phone will ring and is displayed.
·
If the system feature AutoHold is on (consult your system administrator) then you can hold an active call ( ) by
pressing ( ) against the second call. If AutoHold is off, then pressing ( ) against the second call, will drop the first
call.
2420/5420 Phone
IP Office
Page 20
15-601127 Issue 09a (16 July 2009)
Basic Call Handling Features: Hold
2.12 Message
Message is used to access the voicemail system (if installed). Once pressed, the prompts given will depend on the
type of voicemail system. For further details, refer to the Mailbox Users Guides provided for the different voicemail
systems supported by IP Office.
The message lamp at the top of the phone stays lit when there are new messages in your voicemail mailbox, or in any
other mailbox for which you have been configured to receive "Message Waiting Indication".
Note
·
The lamp can also be set to flash when the phone is rung, irrespective of whether you have new messages waiting to
be read.
2.13 Private Call
The Private Call feature is used to prevent any intrusions during the call. Private call can be activated either before or
during a call and will set the phone status to 'cannot be intruded' until you switch the Private Call feature off.
If you place a call to an extension with Private Call on, you will hear the Number Unobtainable tone.
Note
·
Private call is not a default feature. If you require this option, contact your administrator.
2420/5420 Phone
IP Office
Page 21
15-601127 Issue 09a (16 July 2009)
Chapter 3.
Using Speed Dials
2420/5420 Phone
IP Office
Page 23
15-601127 Issue 09a (16 July 2009)
3. Using Speed Dials
The phone can store up to 104 personal speed dials. For a list of the speed dials, press any
SpDial. To exit the current screen, press
and then press
EXIT.
·
The speed dial list is sorted alphabetically.
·
To move between pages, press
·
Press the appropriate letter key to move direct to the first page with a matching name.
·
To call the number, press
·
To perform other actions, press
and
or
.
next to an entry.
.
To access the details of a particular speed dial, press the soft key and select the name from the directory.
Note
·
Speed dials can be used for any numbers that can be manually dialed from the extension. Where a dialling prefix is
required (for example, an external line access digit) then that prefix must be part of the speed dial number.
2420/5420 Phone
IP Office
Page 24
15-601127 Issue 09a (16 July 2009)
Using Speed Dials:
3.1 Adding a New Speed Dial
To add a new speed dial:
1.
Press
SpDial. If
SpDial is not shown and to exit the current screen, press
EXIT and then press
Add. If a message appears stating that the speed dial list is full, you must first delete an existing entry before
adding any new entry. See Deleting a Speed Dial 26 .
To switch between Name and Number entry, press
change accordingly.
2.
next to the item you want to edit. The
options also
With Name selected, begin entering text using the telephone keypad. Each key is marked with the letters and
number it provides. You may have to press the key more than once depending on the character you require. For
example:
·
The key 2 is also marked as A, B and C. To enter a C, press 2 until C is displayed.
·
If the next character you want to enter is on the same key, press
character.
·
By default the first letter is entered in upper-case and the phone then switches to lower-case entry mode. To
change the case of the current character, press
Case.
·
To enter a space, press
·
If you make a mistake, press
·
If you have made a mistake in the middle of a character string and do not wish to backspace and re-enter all the
characters, press
to step back to one character before the point where you wish to edit. Either insert the new
character or press
Backspace to delete the character to the left of the cursor.
·
Press * once enters a . (period) or twice a * (asterisk). To enter more than one * (asterisk) or . (period), press
to move the cursor to the right and then enter the character.
·
Press # once enters a – (dash) or twice enters a # (hash). To enter more than one # (hash) or - (dash), press
to move the cursor to the right and then enter the character.
to move the cursor right and then enter the
Space.
Backspace to delete the character to the left of the cursor.
3.
When the name is set as required, press
4.
Enter the number required using the dialling keypad. For external numbers remember to enter any external dialling
prefix required (e.g. 9).
·
To enter a hyphen, press
more readable.
·
To enter a 1.5 second pause, press
·
To move the cursor left or right, press
Number.
Hyphen. This does not affect the number dialed but may help make numbers
Pause. This will appear as a , (comma) character in the phone number.
and
.
5.
To save the speed dial and return to the speed dial list, press
6.
To return to the speed dial list without saving the changes, press
7.
To return to the call handling screen without saving the changes, press
2420/5420 Phone
IP Office
Save.
Cancel.
EXIT.
Page 25
15-601127 Issue 09a (16 July 2009)
3.2 Dialling a Speed Dial Number
You can use the speed dial directory to make a call with the handset on hook or off hook.
To dial a speed dial number:
1.
Press
SpDial. If
SpDial is not shown and to exit the current screen, press
2.
To display different pages of speed dials, press
page with a matching entry.
3.
When the required entry is displayed, press the adjacent
and
EXIT.
or key the first letter of the required name to jump to the
or
.
3.3 Deleting a Speed Dial
To delete a speed dial:
1.
Press
SpDial. If
SpDial is not shown and to exit the current screen, press
2.
Press
Delete.
3.
Select the speed dial entry you want to delete. To display different pages of speed dials, press
the first letter of the required name to jump to the page with a matching entry.
4.
When the required entry is displayed, press the adjacent
5.
To delete the entry, press
6.
Select another entry to delete or to return to the speed dial list, press
or
EXIT.
and
or key
. A request for confirmation will appear.
Yes or, to exit without deleting, press
Cancel.
Done.
3.4 Editing a Speed Dial
To edit a speed dial:
1.
Press
SpDial. If
SpDial is not shown and to exit the current screen, press
2.
Press
Edit.
3.
Select the speed dial entry you want to edit. To display different pages of speed dials, press
first letter of the required name to jump to the page with a matching entry.
4.
When the required entry is displayed, press the adjacent
5.
Edit the speed dial using the same methods as for adding a new speed dial. See Adding a New Speed Dial
6.
After saving or canceling any changes you will be returned to the speed dial selection list. Select another speed dial
Done.
to edit or to return to the speed dial list, press
or
EXIT.
and
or key the
.
25
.
3.5 Converting a Call Log Entry to a Speed Dial
You can create a new speed dial from a call log entry. See Saving a Call Log Entry to Your Speed Dial List
38
.
This process will start the normal speed entry screen but pre-filled with the name and number from the call log entry.
2420/5420 Phone
IP Office
Page 26
15-601127 Issue 09a (16 July 2009)
Chapter 4.
Using Visual Voice
2420/5420 Phone
IP Office
Page 27
15-601127 Issue 09a (16 July 2009)
4. Using Visual Voice
Visual Voice gives you access to your mailbox using softkeys and, by using the associated feature keys, a more userfriendly option control.
Visual Voice is accessed by pressing
Voice and then selecting from the displayed options:
·
Listen - You can have direct access to your voicemail.
·
Message - You can leave a message directly in a mailbox you specify.
·
Greeting - You can listen to, change or delete your greeting message.
·
Password - You can change your voicemail password
·
Email - You can view or change your email alert status;
·
<Group> - You can have direct access to voicemails for any group you are a member of; if you are the Group
Mailbox Administrator.
Note
·
The email option is only available if VoiceMail Pro is installed, and Voicemail Email has been configured for you.
2420/5420 Phone
IP Office
Page 28
15-601127 Issue 09a (16 July 2009)
Using Visual Voice:
4.1 Listen to Voicemails
To listen to your Voicemails or your Group Voicemails:
1.
Press
Voice.
2.
Press
(25).
Listen (for your messages) or
3.
When prompted, key in the password. If your extension has been configured as a trusted source, the password will
not be required.
Note - If you do not have the required password, contact your administrator.
<group name> (for your hunt group messages), for example, Sales
You will be presented with the following message categories for your messages:
·
New (5)
·
Old (7)
·
Saved (13)
Note - The total number of messages in each category is displayed in brackets.
4.
Use the feature key to select the category, for example
New.
The first message in the selected category will play and the following message handling feature key options are
displayed:
·
Next - Plays next message.
·
<<
- rewinds current message by 5 sec
·
>>
– fast forwards current message by 5 sec
·
Pause- pauses the current message/resumes playing
·
Delete - Delete the current message.
·
Save - Change the current message's category to 'saved'
·
Previous – Plays previous message
·
Copy- Copy the message to another mailbox or mailboxes. If selecting more than one mailbox, the entries must be
separated with a #.
To add a covering message to the copied voicemail.
Press
Copy, and add the recipients. The feature keys change to the copy options.
2.
Press
Pre-Rec
3.
Record your message
4.
Press
Stop
5.
Press
Listen to check your message. You can change the message by selecting Pre-Rec again.
6.
Press
Send.
1.
Note
·
Depending on the number of feature keys available, you may need to use the scrolling facility to see all of the
options.
2420/5420 Phone
IP Office
Page 29
15-601127 Issue 09a (16 July 2009)
4.2 Send a Voicemail
To send a message to another person or Group:
1.
Press
Voice.
2.
Press
Message and dial the extension of the person or Group.
3.
Press
Message again. The soft-key Record is displayed.
4.
Press
Record. The Stop soft-key is displayed.
5.
Record your message and when finished, press
Stop.
After recording your message, the following soft-key options are displayed:
·
Listen - Listen to the message you just recorded.
·
Record - Re-record your message.
·
Others - Add other recipients; each entry separated by a #. Then press
·
Submit - Submit (send) the message.
When you have submitted your message, press
2420/5420 Phone
IP Office
Done.
EXIT to return to the main display.
Page 30
15-601127 Issue 09a (16 July 2009)
Using Visual Voice: Send a Voicemail
4.3 Changing Your Greeting
You can listen to, change and save your current greeting.
Note
·
Visual Voice only modifies your Personal Greeting for All Calls.
To change your mailbox greeting:
1.
Press
Voice.
2.
Press
Greeting. The following options are then displayed on the soft-keys.
·
Record - starts recording.
·
Listen - to hear your current greeting.
·
Submit - saves the new greeting.
·
Delete - deletes your current greeting.
To listen to your current Greeting:
1.
Press
Listen.
To Record a new Greeting:
1.
Press
Record. The Stop soft-key is then displayed.
2.
Record your Greeting and then press
3.
Press
Listen to hear the message you have just recorded; re-record if you are not satisfied with the Greeting.
4.
Press
Submit to save the new Greeting.
5.
Press
EXIT to return to the main display.
2420/5420 Phone
IP Office
Stop.
Page 31
15-601127 Issue 09a (16 July 2009)
4.4 Changing Your Mailbox Password
Note
·
When changing your mailbox password it is advisable not to use sequential numbers (1234, 6789, 8765, etc.) or
existing extension numbers.
To change your Mailbox password:
1.
Press
Voice.
2.
Press
Password.
3.
When prompted, key in your new password (minimum of 4 digits) and press
Done.
The display will exit to the main display if the change was accepted. Otherwise you will be prompted to try again.
2420/5420 Phone
IP Office
Page 32
15-601127 Issue 09a (16 July 2009)
Using Visual Voice: Changing Your Mailbox Password
4.5 Email Alerts
The Email option is displayed if:
·
You have Voicemail pro installed
and
·
Voicemail Email has been configured for you.
To view or change the current email alert status:
1.
Press
2.
Email. You will be prompted for your current voicemail password.
Press
The current voicemail email alert status is shown along with Change and Done soft-keys.
3.
Select either:
Done - To exit leaving the current alert status active
Change - To change the status.
Note - The
Change soft-key will toggle through the alert status, beginning with the current status.
4.
Chose one of the following status:
·
OFF - No email alerts are sent.
·
COPY - An email alert is sent with a copy of the voicemail attached.
·
FWD - An email alert is sent with a copy of the voicemail attached. The original voicemail is deleted from
your voicemail mailbox.
·
5.
Voice.
ALERT- An email alert is sent when there is a new voicemail.
When you have made you selection, press
Done
4.6 Voicemail Transfer
Unlike the standard transfer, Voicemail Transfer allows you to transfer a call to another user's mailbox.
To transfer the call to another mailbox:
1.
Press
Voice.
2.
Key in the user's extension number.
3.
Press
Vmail Transfer.
The call will be transferred directly to the users mailbox; the extension is not alerted.
2420/5420 Phone
IP Office
Page 33
15-601127 Issue 09a (16 July 2009)
Chapter 5.
Using the Call Log
2420/5420 Phone
IP Office
Page 35
15-601127 Issue 09a (16 July 2009)
5. Using the Call Log
The phone maintains a call log, to access, press
Log. This log can store up to 100 entries. These can be a
combination of incoming answered calls, incoming unanswered (missed) calls and outgoing calls.
You can select which types of calls are included in the log. You can also use call log entries to make return calls or
convert the entry into a speed dial for future use.
WARNING
·
Calls that are made using pin codes and other information will appear in the call log. Either Logging of outgoing calls
should be switched off or those call logs removed manually. See Setting Which Calls are Logged 37 .
Notes
·
Only outgoing calls made using the dial pad or a speed dial entry are logged.
·
Call log entries are lost if the phone is disconnected from the IP Office.
To display a screen similar to the following, press
Log:
·
Missed calls are displayed first. You can select from
three options, press
More and then select
All.
·
Logged calls are shown with the most recent first.
·
The name of the called or calling party is shown, if available.
·
The number of the called or calling party is shown.
·
To display further pages of entries, press
·
To display further details of a particular call, press
·
The number of the log entry.
·
The type of log entry, i.e. Answered, Un-answered or Outgoing.
·
The name of the called or calling party is shown (if available).
·
The number of the called or calling party is shown.
·
The date, time and duration of the call.
·
To display the previous or next logged call, press
·
The
and
InAns or
Outgo. Alternatively, to display all
.
or
and
next to a log entry.
.
keys provide a number of actions.
2420/5420 Phone
IP Office
Page 36
15-601127 Issue 09a (16 July 2009)
Using the Call Log:
Using The Call Log
You can make calls directly from the call log. Whilst in the call log you can still make a call by going off-hook, press
SPEAKER and dial a new call. Similarly, you can still receive calls and handle them using the dial pad key functions.
5.1 Setting Which Calls are Logged
Caution
· If you change these settings, any call details already in the call log that no longer match the selection are deleted.
To set which calls are logged:
1.
Press
2.
Press
Log Setup.
A menu showing
Answered,
3.
Option. If
Option is not shown, press
Un-Answered and
To toggle a particular setting between Yes or No, press
Alternatively;
To underline a call type's current setting, press
setting, press Yes/No.
4.
EXIT to exit the current screen.
Outgoing, with their current settings is displayed.
next to it.
next to it. To change the value of the currently underlined
Do one of the following:
· To save the settings and return to the options menu, press
Save. You will hear a confirmation tone.
Note
If you press
Save after changing the settings, any existing call log entries that do not match the call types
selected are deleted from the call log.
· To return to the
Options menu without saving any changes, press
· To return to the call handling screen without saving any changes, press
Cancel.
EXIT.
5.2 Viewing the Call Log
To view the call log:
Log. If
Log is not shown, press any
.
1.
Press
2.
At default, Missed calls are displayed first. You can select from InAns or Outgo. Alternatively, press
More and
select
All to display all three options. To return to Missed or InAns or Outg, press
Back and make your
selection.
3.
To display different pages of log entries, press
4.
and
.
·
To exit the call log and return to the previous screen, press
·
To exit the call log and return to the call handling screen, press
·
To view the details of a particular log entry, press
To return to the previous screen, press
2420/5420 Phone
IP Office
or
Done.
EXIT.
next to the entry.
Done.
Page 37
15-601127 Issue 09a (16 July 2009)
5.3 Making Calls from the Call Log
To make a call from the call log:
1.
Press
2.
At default,
Missed calls are displayed first. You can select from
InAns or
Outgo.
More and select
All to display all three options. To return to
Missed or
Alternatively, press
InAns or
Outg, press
Back and make your selection.
3.
When you locate the entry you want to call, press
4.
To make the call, press
Call.
If the number shown is external but does not include the external dialling prefix used by your phone system, go offhook, dial the prefix and then press
Call.
Log. If
Log is not shown, press any
.
or
next to the entry.
5.4 Saving a Call Log Entry to Your Speed Dial List
To save a call log entry to your speed dial list:
1.
Press
2.
At default, Missed calls are displayed first. You can select from
More and select
All to display all three options. To return to
Back and make your selection.
3.
To display different pages of log entries, press
4.
When you locate the entry you want to call, press
5.
Press
Save. The speed dial editing screen appears, pre-filled with the details from the call log entry. See
Adding a New Speed Dial 25 .
Log. If
2420/5420 Phone
IP Office
Log is not shown press any soft key.
and
InAns or
Missed or
Outgo. Alternatively, press
InAns or
Outg, press
.
or
next to the entry.
Page 38
15-601127 Issue 09a (16 July 2009)
Using the Call Log: Saving a Call Log Entry to Your Speed Dial List
5.5 Deleting a Call Log Entry
To delete a call log entry:
1.
Press
2.
At default,
Missed calls are displayed first. You can select from
InAns or
Alternatively;
More and then select
All. To return to
To display all three options, press
Outg, press
Back and make your selection.
Log. If
Log is not shown, press any soft key.
3.
To display different pages of log entries, press
4.
When you locate the entry you want to call, press
5.
Press
6.
To exit the call log and return to the call handling screen, press
and
Outgo.
Missed or
InAns or
.
or
next to the entry.
Delete. The entry is deleted from the Call Log and the details of the next call are shown.
EXIT.
5.6 Erasing All Logged Calls
Loss of power to the phone will cause all call log entries to be deleted.
The Erase All option deletes the calls you have selected to log. See Setting Which Calls are Logged
37
.
Caution
·
This action also deletes all speed dial entries and phone personalization options. See Default Phone/Erase All Settings
44 .
To erase all logged calls:
1.
Press
Log and then press
2.
Press
Delete. You are presented with a message asking you to confirm that you want to delete all entries.
3.
To remove all logged entries, press
2420/5420 Phone
IP Office
More.
Erase.
Page 39
15-601127 Issue 09a (16 July 2009)
Chapter 6.
Changing Options
2420/5420 Phone
IP Office
Page 41
15-601127 Issue 09a (16 July 2009)
6. Changing Options
6.1 Ring Options
The IP Office uses 'distinctive ringing' for different types of calls:
·
A repeated single ring for internal calls
·
A repeated double ring for external calls
·
A single ring followed by two short rings for ringback calls.
These options are fixed by the IP Office. You can personalize your phone's ringer sound so you can recognize it from
other ringing phones.
You can choose from among eight different ring sounds. This alters the tone and style of ringing used by the phone, the
ring pattern is still controlled by the IP Office according to the call type.
To change the ringer sound:
EXIT and then press
1.
To exit any other mode, press
2.
Press
3.
To select a ringing pattern, press either
selected ringing pattern.
4.
To hear the ringing pattern again, press
Ring Options and then press
Option.
Ring Pattern. A menu with the current ring pattern appears.
and
or press a dial pad key between 1 and 8. You will hear the
Play or re-press the dial pad key.
·
When you have selected a ringing pattern, press
to the options menu.
·
If you want to return to the options menu without changing the ring pattern, press
Save. You will hear a confirmation tone and be returned
Cancel.
Note
·
If you receive a call while selecting a ringer sound, you are automatically returned to the Call Handling screen if set
(see Show Phone Screen below).
To use the Message Lamp for ringing alerts:
EXIT and then press
Option.
1.
To exit any other mode, press
2.
Press
Ring Options and set Flash Message Lamp to Yes or No. When set to Yes, the Message lamp will
flash when you receive a call. Changing this option does not affect the voicemail visual indicator feature.
To automatically show the Call Handling screen:
1.
Press
EXIT to exit any other mode and then press
2.
Press
Ring Options and set Show Phone Screen to Yes or No. If set to Yes then, when you are setting up/
using Speed Dial, Call Log, etc., you are automatically returned to the Call Handling screen when you receive a call.
2420/5420 Phone
IP Office
Option.
Page 42
15-601127 Issue 09a (16 July 2009)
Changing Options: Ring Options
6.2 Adjusting the Display Contrast
You can adjust the contrast level on the phone display. You can choose from among fifteen levels of contrast.
To adjust the display contrast:
1.
To exit any other mode, press
EXIT and then press
2.
Press
3.
To adjust the level of contrast, press
4.
When the contrast is set as required, either:
Option.
Contrast. A menu with the current contrast setting appears.
and
.
·
To return to the options menu, press
·
To return to the call handling screen, press
Done.
EXIT.
6.3 Call Log Setup
Option menu, you can specify which types of calls should be included in the phone's call log. See
Through the
Setting Which Calls are Logged 37 .
6.4 Miscellaneous
The Miscellaneous option only contains one menu item: Stay in Speed Dial.
If Stay in Speed Dial is set to Yes and you access your personal Speed Dial list, the menu will remain displayed
regardless of any calls made or received.
1.
To exit any other mode, press
2.
Press
EXIT and then press
Option.
Miscellaneous and set Stay in Speed Dial to Yes.
2420/5420 Phone
IP Office
Page 43
15-601127 Issue 09a (16 July 2009)
6.5 Using Self Test
Self test can be used to display information about your phone and to check operation of the lamps and display. The
information may be required by your system administrator.
To perform a self test:
1.
To exit any other mode, press
2.
Press
3.
Press and hold
4.
Do one of the following:
EXIT and then press
Option.
Self Test. A screen of information is displayed.
Test. The screen lines go black and all the phone lamps come on.
·
To return to the options menu, press
Done.
·
To return to the Call Handling screen, press
EXIT.
6.6 Default Phone/Erase All Settings
The Erase All option, allows you to reset all personalized settings entered through the phone's Option menus (except
contrast level). This option also deletes all entries in the phones Call Log and Speed Dial lists.
To erase all settings:
EXIT and then press
1.
To exit any other mode, press
2.
Press
3.
To select/de-select an item for erasure, press
selectable for erasure are:
4.
Option.
Erase.
next to an item. A
is shown next to selected items. The items
·
Speed Dials: Selects for erasure all speed dials set in the phone's speed dial store.
·
Call Log: Selects for erasure all entries in the phone's call log.
·
User Labels: Selects for erasure all customized function key labels.
·
Options: Any for erasure or defaulting all other phone options.
·
Language: Selects to default the phone's language setting back to default.
·
All: Selects for erasure or defaulting all of the above.
Press
Erase or
2420/5420 Phone
IP Office
Cancel.
Page 44
15-601127 Issue 09a (16 July 2009)
Changing Options: Default Phone/Erase All Settings
6.7 Language
When the phone is first installed, it is set to display screen text in English. You can select the language that you would
prefer from the following:
English, German (Deutsch), French (Français), Spanish (Español), Italian (Italiano), Dutch (Nederlands), Portuguese
(Português) or Japanese (Katakana characters).
Note
·
This does not alter your user language setting on the phone system.
To select a language:
1.
To exit any other mode, press
EXIT and then press
Option.
2.
Press
Language. A menu listing the available languages appears, with the current language underlined.
3.
Press
or
4.
Do one of the following:
next to the language required. The screen text changes to the language selected.
·
To save the settings and return to the options menu, press
Save. You will hear a confirmation tone.
·
To return to the options menu without saving any changes, press
·
To return to the call handling screen without saving any changes, press
Cancel.
EXIT.
6.8 Automatic Gain Control (AGC)
Automatic Gain Control (AGC) raises the volume when a caller is speaking quietly and lowers the volume when the caller
is loud.
To select Automatic Gain Control:
1.
To exit any other mode, press
2.
Press
3.
next to it.
To toggle a particular setting between Yes and No, press
Alternatively;
To underline a call type's current setting, press
next to it. To change the value of the currently underlined
Yes/No.
setting, press
4.
Do one of the following:
or
EXIT and then press
Option.
until a menu listing the current handset, headset and speaker AGC options is displayed.
·
To save the settings and return to the options menu, press
·
To return to the options menu without saving any changes, press
·
To return to the call handling screen without saving any changes, press
2420/5420 Phone
IP Office
Save. You will hear a confirmation tone.
Cancel.
EXIT.
Page 45
15-601127 Issue 09a (16 July 2009)
Chapter 7.
Function Keys
2420/5420 Phone
IP Office
Page 47
15-601127 Issue 09a (16 July 2009)
7. Function Keys
7.1 Overview of the Function Keys
Both
,
function keys and
to the key shows the feature name.
softkeys can be used to access a range of system features. The display adjacent
Some of these features are default features supported by the phones (e.g. SpDial, Log, Option and Label on the
softkeys) and are always available. Others are system features that can only be programmed by the system
administrator for function keys.
In addition, there are a number of system features that you can always access yourself by the use of short codes.
Refer to System Features Introduction 56 for details of system features that you can always access yourself by dialling
short codes, e.g. to listen to your voicemail messages, dial *17.
and
function keys on each page could be used for
The main screen has three pages. This means that the eight
up to 24 features. However, it is strongly recommended that all three call appearance keys remain at their default
settings. Therefore, there are 21 soft function keys that can be allocated to system features.
To move between pages, press
and
.
In the following example:
·
The first three keys have been set as call appearance lines.
·
Keys 4 and 5 have been set to access the Admin and Admin1 programmable functions.
·
Key 6 has been set to monitor system park slot 1. The
·
Key 7 has been set to the SAC (Send All Calls) function.
indicates a call is currently parked in slot 1.
·
Key 8 has been set to VMOn, a function which toggle use of the voicemail mailbox as on/off. The
function is currently on.
·
To display the other two pages of programmed functions set for this phone, press either
or
indicates that this
.
Changing the labels of the function keys:
You can personalize the function key labels. For example, you can change SAC to Send All for instance. See Changing
Function Key Labels 54 .
Programming your own features:
If the phone has been setup with either or both the Admin and Admin1 features assigned to display keys, you can select
and program your own feature choices against other keys. See Function Key Programming 50 .
2420/5420 Phone
IP Office
Page 48
15-601127 Issue 09a (16 July 2009)
Function Keys: Overview of the Function Keys
7.2 Display Mode
The phone has two display modes. These control the order in which functions are assigned to the display keys. The
modes are:
·
Normal Mode:
In this mode the 3 pages of
and
are ordered sequentially.
SpDial, Log, Option and Label options.
·
at the base of each page provide the
Call Center Mode:
In this mode some of the
and
functions are repeated against
on the first two screen pages. The
keys for SpDial, Log and Option are only shown on the third screen page.
To change the Display Mode:
1.
Press
Option. If
Option is not shown, press
EXIT to exit the current screen.
2.
Press
Display Mode. A menu showing the current setting appears.
3.
To change the current setting, either press
4.
Do one of the following:
next to the setting or press
Yes/No.
Save. You will hear a confirmation tone.
·
To save the settings and return to the Options menu, press
·
To return to the Options menu without saving any changes, press
·
To return to the Call Handling screen without saving any changes, press
2420/5420 Phone
IP Office
Cancel.
EXIT.
Page 49
15-601127 Issue 09a (16 July 2009)
7.3 Function Key Programming
If any one of the keys on the telephone is programmed with an Admin or Admin 1 feature key, it allows you to program
further features against other function keys. Both Admin and Admin1 are allocated to your function keys by your
system administrator and will appear on a menu screen that is similar to the following:
The two tables below list the user programmable features available from Admin and Admin1. For full details of how
each function works, see System Features 56 .
Admin: The programmable functions available via an Admin key are:
2420/5420 Phone
IP Office
Name
Description
Toggles
Data
Acct
Account Code Entry
No
Optional
AD
Abbreviated Dial
No
Yes
Admin
Self-Administer
No
No
AutCB
Automatic Callback
Yes
No
CFrwd
Call Forwarding All
Yes
Optional
CPark
Call Park
Yes
Optional
CPkUp
Call Pickup
No
No
Dir
Directory
No
No
DPkUp
Directed Call Pickup
No
Yes
DROP
DROP
No
No
GrpPg
Group Paging
No
Yes
HdSet
HEADSET Toggle
Yes
No
HfAns
Internal Auto-Answer
Yes
No
HGNS+
Set Hunt Group Night Service
Yes
Yes
Park
Call Park to Other Extension
No
Yes
Prog
Abbreviate Dial Program
No
Yes
RngOf
Ringer Off
Yes
No
SAC
Send All Calls
Yes
No
Spres
AD Suppress
Yes
No
Timer
Timer
Yes
No
TmDay
Time of Day
Yes
No
Page 50
15-601127 Issue 09a (16 July 2009)
Function Keys: Function Key Programming
In addition to the above, there is a key labeled Expl? This key enables you to change the display from the shorthand
version displayed at default to a longhand version of your own. See Shorthand Programming Mode 52 and Longhand
Programming 53 respectively.
Admin1: The programmable functions available via an Admin1 key.
Name
Description
Toggles Data
Park
Park
No
Yes
<User>
User
No
Yes
<Group>
Group
No
Yes
<Number> Dial
No
Yes
Flash
No
No
2420/5420 Phone
IP Office
Hook Flash
Page 51
15-601127 Issue 09a (16 July 2009)
7.4 Shorthand Programming Mode
1.
Press
2.
The Admin or Admin1 menu is displayed, similar to the following:
Admin Pages
Admin or
Admin 1. See Function Key Programming
50
.
With the exception of Expl?, the names shown are the features that you can assign to soft keys. When Admin has
been selected, you can display the full name of the feature by pressing Expl?. See Longhand Programming 53 .
Admin1 Page
3.
On the Admin pages, press
and
to move through the list of feature.
4.
When the function required is shown, press
5.
If the function requires some data to be entered, [ ] is shown at the bottom of the display. Enter the data using the
normal phone keypad.
6.
The upper part of the display reverts to showing the functions currently assigned to
7.
To select the display key against which to program the new function, press
Caution
·
8.
9.
adjacent to its name.
or
and
.
.
Do not select the slot used for the Admin function. Replacing this function will lock the phone for further
programming until reset through the phone system.
If the display slot is not already used, the display shows BUTTON PROGRAMMED!.
·
To end programming, press
·
To continue programming other functions, press
EXIT.
Cont.
Repla, Keep and Delet are shown along the right-hand edge of the display.
. BUTTON PROGRAMMED! is
·
To replace that existing function with the one just programmed, press Repla
displayed.
·
To keep the existing function and forget the function just programmed, press Keep
·
To delete the existing function and forget the function just programmed, press Delet
2420/5420 Phone
IP Office
.
.
Page 52
15-601127 Issue 09a (16 July 2009)
Function Keys: Shorthand Programming Mode
7.5 Longhand Programming
1.
Press
2.
To switch to longhand programming mode, press Expl?
3.
Press Next
4.
If the function requires some data to be entered, [ ] is shown at the bottom of the display. Enter the data using the
normal phone keypad. The upper part of the display reverts to showing the functions currently assigned to
and
.
5.
To move between the pages of display keys, press
6.
To select the display key against which to program the new function, press
Caution
·
7.
9.
Admin. See Display Key Programming
50
.
.
until the required function required is shown, then press Selct
and
.
.
or
.
Do not select the slot used for the Admin function. Replacing this function will lock the phone for further
programming until reset through the phone system.
If the display slot is not already used, the display shows BUTTON PROGRAMMED!.
EXIT.
·
To end programming, press
·
To continue programming other functions, press
Cont.
If the display slot already has a programmed function, the display shows FEATURE ON BUTTON. Repla, Keep and
Delet are shown along the right-hand edge of the display.
·
To replace that existing function with the one just programmed, press Repla
BUTTON PROGRAMMED! as above.
·
To keep the existing function and forget the function just programmed, press Keep
·
To delete the existing function and forget the function just programmed, press Delet
2420/5420 Phone
IP Office
. The display then shows
.
.
Page 53
15-601127 Issue 09a (16 July 2009)
7.6 Changing Function Key Labels
You can replace the default label shown for any function key with you own custom label of up to 13 characters.
1.
To exit any other mode, press
EXIT and then press
Label.
·
Edit allows you replace the current labels, see the steps below.
·
Inspect displays the default labels.
·
Restore replaces any custom labels with the default labels.
·
Done exits the button labelling options.
2.
Press
3.
Select the function key whose label you wish to change.
4.
Begin entering the New Label text using the phone keypad:
Edit.
·
Each number key is marked with the letters it provides. You may have to press the key more than once
depending on the character required. For example, the key 6 is also marked as M, N and O. To enter an O, repress the 6 key until an O is displayed.
·
If the next character you want is on another key, simply key the next character.
·
If the next character you want to enter is on the same key just used, press
enter the character.
·
Press * once enters a . (period). Pressing it twice enters a * (asterix).
·
Press # once enters a - (dash). Pressing it twice enters a # (hash).
·
By default the first letter entered and the first letter after any space are entered in upper-case whilst all other
character are entered in lower-case. To change the case of the current character, press
Case.
·
To enter a space, press
·
To move the cursor one space right, press
to move the cursor right and then
Space.
.
·
If you make a mistake, press
·
If you have made a mistake in the middle of a character string and do not wish to backspace and re-enter all the
characters, press
to step back to one character before the point where you wish to edit. Either insert the new
character or press
Backspace to delete the character to the left of the cursor.
Backspace to delete the character to the left of the cursor.
·
To delete all the current text, press
5.
When the new name is set as required, press
changes, press
Cancel.
6.
Select another button to re-label or press
2420/5420 Phone
IP Office
Clear.
Save. To return to the label options screen without saving the
Done.
Page 54
15-601127 Issue 09a (16 July 2009)
Chapter 8.
System Features
2420/5420 Phone
IP Office
Page 55
15-601127 Issue 09a (16 July 2009)
8. System Features
8.1 Introduction
As well as accessing specific features on your phone, you can access a number of system features by dialling short codes.
These instructions are for the system's default configuration. They assume that you are using the default feature codes.
It also assumes that you have full access to all features and the public phone network.
8.2 Ring Back
If your system administrator has allocated you the Ring Back When Free feature and you call an extension that does not
answer or is busy, you can:
1.
Press
RBak to set a callback on that extension. When the extension you called becomes free, your phone will
ring (a burst of three rings).
2.
Lift the handset and the extension is called automatically.
8.3 Call Forwarding
Your calls can be forwarded to another extension or an external number when:
·
You are away from your desk (on no answer).
·
Your extension is busy (on all Call Appearance keys).
·
You are away from the office (e.g. when you are on holiday).
The following options are available for call forwarding:
·
To set the number to which your calls are forwarded, dial *07*201# (forwarding to 201 in this example).
·
To switch Forward Unconditional On (i.e. not Hunt Group), dial *01. The letter D is displayed. To switch it off, dial
*02.
·
To switch Forward On Busy On, dial *03. To switch it off, dial *04.
·
To switch Forward On No Answer On, dial *05. To switch it off, dial *06.
·
To switch Forward Hunt Group Calls On, dial *50. To switch it off, dial *51. This setting is for Forward Unconditional
only.
·
To Cancel All Forwarding, dial *00.
Note
·
Cancelling all forwarding will also cancel any Diverts you have set.
2420/5420 Phone
IP Office
Page 56
15-601127 Issue 09a (16 July 2009)
System Features: Call Forwarding
8.4 Diverting Calls
You can divert your calls to another extension using Follow Me. Unlike Forward, Follow me can only be used to divert
calls to another internal extension on the same IP Office.
Note
·
If you do not answer calls at the temporary extension, they are forwarded to your own voicemail or call forwarding
number.
To use Follow-Me-Here from another extension:
In this case, N is your home extension
·
Dial *12*N# from the extension you are temporarily using.
·
Dial *13*N# to re-direct the calls back to your own extension, before you return to it.
To use Follow-Me-To from your home extension:
In this case, N is the extension to which you want your calls diverted.
·
Dial *14*N# from your own extension.
·
Dial *14*# to cancel either feature from your own extension.
Notes
·
If you use the option Cancel All Forwarding
·
Follow Me does not apply to the following call types:
56
, your Follow Me will also be cancelled.
— Voicemail Callback
— Automatic Call Back
— HOLD or Park return.
2420/5420 Phone
IP Office
Page 57
15-601127 Issue 09a (16 July 2009)
8.5 Do Not Disturb
You may choose to receive no calls at all or only those from particular callers on your exceptions list:
·
To switch Do Not Disturb on (with or without exceptions), dial *08. An N is displayed. To switch it off, dial *09.
·
To add a number to the exception list, dial *10*N#.
·
To delete a number from the exception list, dial *11*N#.
Note
·
Your callers, other than your exceptions, either hear busy tone or are re-directed to your voicemail.
·
The only call that will ignore the Do Not Disturb rule will be one where you were the original caller, then performed
an unsupervised transfer to another extension. If that extension does not answer, the call will be re-directed to you
as the originator.
8.6 Parking Calls
You can park one or more calls; allowing you to make and receive other calls. You can also arrange for the parked call to
be retrieved by another extension.
The system only allows calls to be parked for a short while before reconnecting them to the user who parked the call; the
default setting is 5 minutes. Once the set time is reached, the parked call will ring back if your extension is idle.
Note
·
To park a call using the short codes, the call must first be put on Hold
20
.
To park a call to be picked up by any extension:
·
Dial *37*N# - Where N is the slot id you have assigned.
Inform your colleagues of the parked call and the slot id you have assigned.
To Un-park a call from another extension:
·
Dial *38*N# - Where N is the assigned slot id.
To Park a call to your local extension:
·
Dial *37#
When you park a call to your local extension, it is automatically given a slot id number based on your extension
number followed by 0. If you park another call, it is given your extension number followed by 1 and so on up to 9.
For example: if your extension is 201, the first parked call will be given the slot id 2010.
To Un-park a call on your local extension:
·
Dial *38*# - If you have more than one call parked, the call parked first will be the first call to be unparked
Note
·
Feature keys can be setup to park and un-park calls. If required, contact your administrator.
2420/5420 Phone
IP Office
Page 58
15-601127 Issue 09a (16 July 2009)
System Features: Parking Calls
8.7 Voicemail
You can enable voicemail to allow callers to leave messages when you are out of the office, away from your desk or
engaged on another phone call. Voicemail messages can be retrieved internally or externally via any phone. Your
voicemail may be set up to deliver your messages by calling you whenever you hang up: this feature is known as
Voicemail Ringback.
Note
·
Not all systems support voicemail or have voicemail installed.
The following options are available for voicemail:
·
To switch voicemail on, dial *18. To switch it off, dial *19.
·
To retrieve your voicemail, dial *17.
·
To turn Voicemail Ringback on, dial *48. To turn it off, dial *49.
Dialling a number while listening to your messages invokes further facilities:
·
Once messages have been delivered, they are held on the system for 24 hours (this is fixed for Voicemail Lite, but
can be varied by your system administrator if your IP Office is equipped with VoicemailPro).
·
You can collect your voicemail from another extension by using the PIN your system administrator has set up for
you. You can collect your messages if you are out of the office, by either dialling from a number that has been
registered for the purpose or by dialling your extension number and PIN when prompted. If validation is successful,
then dial 2 to retrieve your mail.
·
The system administrator also specifies the reception number, to which the call is diverted if the caller dials 0, and
your email address if your voicemail and email are integrated.
2420/5420 Phone
IP Office
Page 59
15-601127 Issue 09a (16 July 2009)
8.8 Default Feature Codes
The following are the normal default feature codes available to all users. Your system administrator may add additional
codes for other features and for speed dials.
The N, where shown, should be replaced by the appropriate number. For example, with *07*N#, replace N with the
extension to which you want your calls forwarded when you have forwarding switched on.
*00
Cancel All Forwarding
*32*N#
Call Pick Up Extension
*01
Forward Unconditional On
*33*N#
Call Queue
*02
Forward Unconditional Off
*34
HOLD Music
*03
Forward On Busy On
*35*N#
Extn Login
*04
Forward On Busy Off
*36
Extn Logout
*05
Forward On No Answer On
*37*N#
Park Call
*06
Forward On No Answer Off
*38*N#
Ride Call
*07*N#
Forward to Number
*39
Relay On
*08
Do Not Disturb On
*40
Relay Off
*09
Do Not Disturb Off
*41
Relay Pulse
*10*N#
Do Not Disturb Exception Add
*42
Relay On
*11*N#
Do Not Disturb Exception Delete
*43
Relay Off
*12*N#
Follow Me Here
*44
Relay Pulse
*13*N#
Follow Me Here Cancel
*45*N#
Call Steal
*14*N#
Follow Me To
*46
Call Steal
*15
Call Waiting On
*47
CONFERENCE Add
*16
Call Waiting Off
*48
Voicemail Ringback On
*17
Voicemail Collect
*49
Voicemail Ringback Off
*18
Voicemail On
*50
Forward Hunt Group Calls On
*19
Voicemail Off
*51
Forward Hunt Group Calls Off
*20*N#
Set Hunt Group Night Service
*52
Clear Call
*21*N#
Clear Hunt Group Night Service
*53*N#
Call Pickup Members
*29
Toggle Calls
*57*N#
Forward on Busy Number
*30
Call Pick Up Any
*70*N#
Dial Physical Extn by Number
*31
Call Pick Up Group
*71*N#
Dial Physical Extn by ID
2420/5420 Phone
IP Office
Page 60
15-601127 Issue 09a (16 July 2009)
Chapter 9.
EU24 Expansion Module
2420/5420 Phone
IP Office
Page 61
15-601127 Issue 09a (16 July 2009)
9. EU24 Expansion Module
9.1 EU24 Overview
The EU24 Expansion Module is an optional device that can be connected to your 2420/5420 phone to extend the number
of call appearance and feature buttons available on the phone.
The expansion module has 24 buttons arranged in two columns. Depending on how they have been programmed by your
system administrator, these buttons can be used for call appearances or features. You can adjust the viewing angle of
the EU24 display to match that of your phone.
The following figure shows a top view of the EU24 (the left hand column is displayed).
1.
Call Appearance/Feature Button.
2.
Feature Active icon for feature in right column.
3.
Alternate Display Button.
4.
Feature Active icon for feature in left column.
5.
Display.
2420/5420 Phone
IP Office
Page 62
15-601127 Issue 09a (16 July 2009)
EU24 Expansion Module: EU24 Overview
9.2 Connection
Before you can begin using the EU24 Expansion Module, the module must be connected to the phone according to the
instructions in the EU24 Expansion Module Installation and Safety Instructions (555-233-136).
9.3 Using the EU24 Expansion Module
The following section explains how to use the features of the EU24 Expansion Module. For more information, consult your
system administrator.
Viewing the Alternate Display:
Although the EU24 Expansion Module supports an additional 24 call appearance/feature keys, it only displays the key
labels and icons for one column at a time. A dotted line separates the left column from the right column.
When you are viewing the labels and icons for the left column, the icons for the right column are displayed to the right of
the dotted line. To view the column not currently displayed, press the Alternate Display button.
Selecting a Call Appearance/Feature Key:
To select an available call appearance or feature, press the button next to the label in the column currently displayed.
If the call appearance or feature is not currently displayed, press the Alternate Display button to access the additional 12
call appearance/feature button labels.
Understanding Call Appearance/Feature Key Status Icons:
When a call arrives for a call appearance on the EU24 Expansion Module, the bell icon blinks on the corresponding call
appearance. To answer the call, press the associated call appearance button.
The icons displayed on the call appearance allow you to determine the status (for example, on hold) of each call on the
EU24 Expansion Module. Icons also indicate whether a feature has been administered for a particular button on the EU24
Expansion Module.
2420/5420 Phone
IP Office
Page 63
15-601127 Issue 09a (16 July 2009)
Index
Index
A
Adding 25
Adding,New Speed Dial 25
Adjusting 43
Adjusting,Display Contrast 43
AGC 45
All Logged Calls 39
All Logged Calls,Erasing 39
Answer 14
Answer,Call 14
Automatic Gain Control 45
B
Back 56
C
Call 14, 15, 38, 58
Call Appearance Keys 8
Call Appearance Keys Icons 9
Call Forwarding 56
Call Log 36, 37, 38
Call Log Entry 26, 38, 39
Call Log Entry,Converting 26
Call Log Entry,Deleting 39
Call Log Entry,Saving 38
Call Log Setup 43
Call Log,Overview 36
Call Log,Viewing 37
Call,Answer 14
Call,Clearing 15
Call,Make 15
Call,Making 38
Call,Parking 58
changing 31, 32, 42, 54
changing,Function Key Labels 54
changing,Your Greeting 31
Changing,Your Mailbox Password 32
Clearing 15
Clearing,Call 15
conference 8, 11, 16
Connection 63
Converting 26
Converting,Call Log Entry 26
F
Function Key Labels 54
Function Key Labels,Changing 54
Function Key Programming 50
Function Keys 48
Function Keys,Overview 48
H
Headset Working 17
hold 8, 14, 17, 20, 44, 63
L
Language 45
Listen 29
Listen,Voicemails 29
Logged 10, 37
Logged,Off 10
Logged,On 10
Longhand Programming 53
M
Making 15, 38
Making,Call 15
Making,Calls 38
Message 21
Miscellaneous 43
Mute 20
N
New Speed Dial 25
New Speed Dial,Adding 25
Not Disturb 58
O
Off 10
Off,Logging 10
On,Logging 10
Overview 24, 28, 36, 48
Overview,Call Log 36
Overview,Function Keys 48
Overview,Speed Dials 24
Overview,Visual Voice 28
P
Parking 58
Parking,Calls 58
Private Call 21
D
R
Default Feature Codes 60
Default Phone/Erase All Settings 44
Deleting 26, 39
Deleting,Call Log Entry 39
Deleting,Speed Dial 26
Dialling 26
Dialling,Speed Dial Number 26
Display 11
Display Contrast 43
Display Contrast,Adjusting 43
Display Mode 49
Divert 57
Redial 19
Ringer Options 42
E
Editing 26
Editing,Speed Dial 26
Email Alerts 33
Erasing 39
Erasing,All Logged Calls 39
EU24 Expansion Module 63
EU24 Expansion Module,Using 63
EU24 Overview 62
2420/5420 Phone
IP Office
S
Saving 38
Saving,Call Log Entry 38
Send 30
Send,Voicemail 30
Setting 37
Setting,Which Calls 37
Shorthand Programming Mode 52
Speakerphone 18
Speed Dial 19, 24, 26
Speed Dial Number 26
Speed Dial Number,dialling 26
Speed Dial,Deleting 26
Speed Dial,Editing 26
Speed Dial,Overview 24
System Features 9
System Features Introduction 56
T
Transfer 16
Page 65
15-601127 Issue 09a (16 July 2009)
U
User 11
Using 63
Using Self Test 44
Using The Call Log 36
Using,EU24 Expansion Module 63
V
Viewing 37
Viewing,Call Log 37
Visual Voice 28
Visual Voice,Overview 28
Voicemail 30, 59
Voicemail TRANSFER 33
Voicemail,Send 30
Voicemails 29
Voicemails,Listen 29
W
Which Calls 37
Which Calls,Setting 37
Y
Your Greeting 31
Your Greeting,Changing 31
Your Mailbox Password 32
Your Mailbox Password,Changing 32
Your Speed Dial List 38
2420/5420 Phone
IP Office
Page 66
15-601127 Issue 09a (16 July 2009)
2420/5420 Phone
IP Office
Page 67
15-601127 Issue 09a (16 July 2009)
Performance figures and data quoted in this document are typical, and must be
specifically confirmed in writing by Avaya before they become applicable to any
particular order or contract. The company reserves the right to make alterations
or amendments to the detailed specifications at its discretion. The publication of
information in this document does not imply freedom from patent or other
protective rights of Avaya or others.
Intellectual property related to this product (including trademarks) and registered
to Lucent Technologies have been transferred or licensed to Avaya.
All trademarks identified by the ® or ™ are registered trademarks or trademarks,
respectively, of Avaya Inc. All other trademarks are the property of their
respective owners.
This document contains proprietary information of Avaya and is not to be
disclosed or used except in accordance with applicable agreements.
Any comments or suggestions regarding this document should be sent to
"wgctechpubs@avaya.com".
© 2009 Avaya Inc. All rights reserved.
Avaya
Unit 1, Sterling Court
15 - 21 Mundells
Welwyn Garden City
Hertfordshire
AL7 1LZ
England.
Tel: +44 (0) 1707 392200
Fax: +44 (0) 1707 376933
Web: http://marketingtools.avaya.com/knowledgebase
2420/5420 Phone
IP Office
Page 68
15-601127 Issue 09a (16 July 2009)