AVE 2PSWT Switch User Manual

2PSWT
2-Position Sequencing,
Homing Switcher
Operation Manual
1
WARNING: TO PREVENT FIRE
OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS
APPLIANCE TO RAIN
OR MOISTURE
WARNING!
This equipment generates, uses, and can radiate radio frequency energy
and if not installed and used in accordance with the instructions manual,
may cause interference to radio communications. It has been
tested and found to comply with the limits for a class A computing device
pursuant to subpart J of part 15 of FCC rules, which are designed to provide
reasonable protection against such interference when operated in a
commercial environment.
Operation of this equipment in a residential area is likely to cause interference
in which case the user at his own expense will be required to take whatever
measures
CAUTION!
RISK OF ELECTRICAL SHOCK
DO NOT OPEN CAUTION!
TO PREVENT ELECTRIC SHOCK
DO NOT REMOVE COVER.
NO USER SERVICEABLE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
The lightning flash with the arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute
a risk of electrical shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
2
INTRODUCTION
The 2PSWT is a 2 position sequencing, homing switcher. The front
panel toggle switch allows for automatic sequencing, or homing of
the 2 video inputs. Sequencing is controlled by a front panel
recessed dwell pot. This pot is recessed to eliminate accidental
adjustment. The dwell adjustment varies from approximately .2
second to 60 seconds.
OPERATION
When the toggle switch is in the up position the switcher homes to
camera #1. When the toggle switch is in the down position the
switcher homes to camera #2. When the toggle switch is in the
center position the switcher sequences between the two cameras.
DWELL
The dwell or time that each camera appears on screen can be
adjusted by the recessed front panel control. This can be varied
from approximately .2 second to 60 seconds. Use a small flat
bladed screwdriver to adjust this control. Turning this pot to the right
increases the dwell time.
POWER
The switcher is powered by the included wall transformer. The unit
can be powered from 5 to 12VDC. The center post of the DC Coax
is POSITIVE.
CONNECTIONS
The VIDEO inputs are BNC type connectors. The inputs are 75 ohm
terminated and require 1V P-P. The output is 1V P-P and will drive
a 75 ohm load. Connect the video cameras to the switcher in the
desired order. Connect Video out to your VCR or Monitor. Plug in
the DC Coax connector. The switcher is now operational. Select the
desired front panel controls and adjust the dwell.
3
2PSWT Front Panel
2PSWT Rear Panel
Note:
The 2PSWT front panel toggle switch merely switches +voltage for
camera #1 and ground for camera #2. An external relay or transistor
could be user connected to this switch internally to produce a low
cost alarming 2 position switcher. Remove the toggle switch and
wire the alarm trigger to the center position and to ground on the
PCB.
4
SPECIFICATIONSCIFICATIONS
Video Inputs: ...................................1V P-P Terminated @ 75 ohm
..............................................toggle switch selectable
Toggle positions:.............................Home 1, Sequence & Home 2
Video Output: ....................................................1V P-P into 75 Ohm
Dwell adjust: .............................................Front panel recessed pot
Dwell Time: .................From approximately .2 second to 1 minute
Power: .................................................................................5-12VDC
Power Supply.......................................9-12VDC Wall Transformer
Connectors:
Video In/Out ................................................................................BNC
Power Input .............................................DC Coax 2.1mm x 5.5mm
Alarm Input ...........................Screw terminal with quick disconnect
Mechanical:
Case ........................ Beige Metal 3.15” W x 4.53” L x 1.18” H
(80mm W x 115mm L x 30mm H)
Weight........................................................................0.40 kg.(0.84 lbs.)
Box Size..................................................8.0” W x 7.0” L x 2.5” H
(240mm W x 178mm L x 64mm H)
5
LIMITED WARRANTY
(Terms and Conditions)
For 2 Years from the date of shipment, Seller warrants to Buyer that the Product is free from defects in material or workmanship under normal use and
service. Equipment manufactured by other than Seller but furnished by Seller
carries the same warranty to Buyer as Seller receives from the other manufacturer, notwithstanding any provision to the contrary. If Buyer has specified a
particular manufacturer’s product which is not the brand standardly supplied by
Seller, Buyer shall look only to the other manufacturer’s warranty and Seller
shall not warrant such item.
EXCLUSIONS. Seller’s warranty does not cover the following:
(1)
(2)
(3)
(4)
(5)
(7)
(9)
(10)
in-transit damage claims, improper handling by carrier or post office
(Note: only the consignee of the shipment can file a claim with the
common carrier)
damages caused by incorrect use, modification, carelessness,
improper storage, hostile operating conditions, or unauthorized
service, installation or repairs without proper training from the Seller
damages caused by fire, flood, lightning, collision, acts of God or
other events beyond the control of Seller
products or parts thereof that have had serial numbers removed,
altered or defaced
products returned without an RMA number and sales or delivery
receipt showing the date of original purchase
use of components that do not meet Seller’s specifications
external parts such as cabinets or keypads
periodic maintenance and adjustments resulting from normal use
WARRANTIES EXCLUDED, SELLER EXPRESSLY DISCLAIMS AND EXCLUDES ANY EXPRESS OR IMPLIED WARRANTY OR MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEEDS OR IS INCONSISTENT WITH THE WARRANTY HEREIN EXPRESSLY SET FORTH.
NON-WARRANTY CLAIMS. In the event Buyer makes a warranty claim and
Seller’s warranty does not apply, Buyer shall reimburse Seller for all reasonable
expenses incurred by Seller in diagnosing the installation/repair problem.
6
BUYER’S EXCLUSIVE REMEDIES. If the Product supplied shall fail to conform to the contract or any applicable warranty, Buyer shall immediately notify
Seller of such condition and afford Seller a reasonable opportunity to inspect
said Product. Seller shall, at its option, either repair or replace such nonconforming Product. Seller shall not be responsible for labor charges for removal
or installation of such equipment or material or charges for transportation,
handling and shipping except as provided in Seller’s written service policy. No
Product shall be returned without Seller’s prior written consent.
SELLER SHALL NOT BE LIABLE FOR ANY SPECIAL, DIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OF A COMMERCIAL NATURE
ARISING OUT THE USE OF OR INABILITY TO USE SELLER’S PRODUCT
BY REASON OF THE FACT THAT SUCH PRODUCT DOES NOT CONFORM
TO THE CONTRACT OR TO ANY EXPRESS OR IMPLIED WARRANTY.
SELLER’S MAXIMUM LIABILITY SHALL BE LIMITED TO THE COST OF
REPAIR AND/OR REPLACEMENT OF THE PRODUCT CLAIMED TO BE
DEFECTIVE OR NONCONFORMING, SUBJECT TO SELLER’S RIGHT OF
REMOVAL AND RETURN OF PRODUCT.
All of the foregoing constitute Buyer’s sole and exclusive remedy and Seller’s
sole and exclusive liability for supplying nonconforming or defective Product.
RETURNS. AVE products are fully inspected and carefully packed to ensure
you are delivered a quality product in good condition. If you are not fully
satisfied with our product, returns of standard stocking items with no restocking fee can be made within thirty (30) days of invoice to Buyer. All such returns
must have prior consent of Seller by obtaining an RMA number and must
include the sales or delivery receipt showing the date of original purchase and
be in an unused condition contained in its original packaging. Any other returns must have prior written consent of Seller and are subject to a restocking
fee of fifteen percent (15%) and freight charges.
RMA NUMBER. The RMA (Return Material Authorization) number must be
obtained by contacting Seller prior to the shipment of the the product for return. The RMA number is valid only for 15 days from the date of issue. The
RMA number must be clearly displayed on all shipping labels.
7
ASIA
AVE (Thailand) Co., Ltd.
217/4 Crystal Garden
Soi 4 (Nanatai), Sukhumvit Rd.
Klongtoey, Klongtoey
Bangkok, 10110 Thailand
Tel: 662-656-8231
Fax: 662-656-9554
Email: ave@avethailand.com
www.avethailand.com
NORTH AMERICA
AVE USA
2000 West Governors Circle, Suite E
Houston, Texas 77092
Tel: 281-443-2300
Fax: 281- 443-8915
Email: aveus@ave-us.com
www.americanvideoequipment.com
WESTERN EUROPE
AVE Multiview
Granyte House, Delamare Road
Cheshunt, Hertfordshire
EN8 9SP
Tel: 440-870-770-9323
Fax: 440-870-770-9363
Email: ave-uk@multiview.net
www.multiview.net
8