AVerMedia Technologies EB1004 BAK DVR User Manual

AVerMedia® EB1004 BAK
Real-time Security DVR
Operations Manual
P/N: 300AABLP
MADE IN TAIWAN
FCC NOTICE
This device has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a commercial, industrial or business environment. This equipment can generate, use and
radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
WARNING
TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION ON MODIFICATIONS
To comply with the limits for the Class A digital device, pursuant to Part 15 of the FCC Rules, this device
must be installed in computer equipment certified to comply with the Class A limits. All cables used to
connect the computer and peripherals must be shielded and grounded. Operation with non-certified
computers or non-shielded cables may result in interference to radio or television reception.
Any changes or modifications not expressly approved by the grantee of this device could void the user's
authority to operate the equipment.
CE NOTICE
This is a Class A product.
DISCLAIMER
No warranty or representation, either expressed or implied, is made with respect to the contents of this
documentation, its quality, performance, merchantability, or fitness for a particular purpose. Information
presented in this documentation has been carefully checked for reliability; however, no responsibility is
assumed for inaccuracies. The information contained in this documentation is subject to change without
notice.
In no event will AVerMedia be liable for direct, indirect, special, incidental, or consequential damages
arising out of the use or inability to use this product or documentation, even if advised of the possibility of
such damages.
TRADEMARKS
AVerMedia is a registered trademark of AVerMedia TECHNOLOGIES, Inc. All other products or
corporate names mentioned in this documentation are for identification and explanation purposes only, and
may be trademarks or registered trademarks of their respective owners.
COPYRIGHT
© 2004 by AVerMedia TECHNOLOGIES, Inc. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any
form by any means without the written permission of AVerMedia TECHNOLOGIES, Inc.
VER 01
CAUTION
DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Table of Contents
TIME SET .............................................................................................18
VGA SETUP .........................................................................................19
Introduction .........................................................................................................3
MOTION SETUP ..................................................................................19
Features and Specifications .............................................................................3
HARD DRIVE SETUP .............................................................................19
Front Panel ......................................................................................................4
OVERWRITE ENABLED ....................................................................21
Back Panel.......................................................................................................6
MASTER HDD SIZE and MASTER HDD USED ...............................21
Setting Up the DVR Unit.................................................................................6
MASTER HDD FORMAT ....................................................................21
Installing Hard Drives .................................................................................6
SLAVE HDD SIZE and SLAVE HDD USED.......................................21
Install the Hard Drive in a Removable Case................................................7
SLAVE HDD FORMAT ........................................................................21
Install a Removable Hard Drive Case in a PC (Optional) ...........................8
SENSOR SETUP.......................................................................................22
Connecting Devices.....................................................................................8
SENSOR RECORD TIME ....................................................................22
Basic Devices ..........................................................................................8
ALARM OUT TIME .............................................................................20
Optional Devices .....................................................................................9
CHANNEL1 ~ CHANNEL4 .................................................................20
Operating the DVR Unit....................................................................................10
Connect to a PC .................................................................................................23
First Time Use ...............................................................................................10
FIRST TIME USE .....................................................................................23
Surveillance Screen .......................................................................................10
OPERATING EB-DVR PLAYBACK APPLICATION.........................25
Video Recording and Playback......................................................................11
CHANNEL SELECTION......................................................................26
Setup Menu........................................................................................................13
FREE VIDEO PLAYBACK ..................................................................27
MAIN MENU................................................................................................14
CATCH IMAGE AND VIDEO .................................................................28
CAMERA SELECT...................................................................................14
SNAPSHOT ..........................................................................................28
RECORD SELECT ...................................................................................15
PRINT ...................................................................................................28
RECORD MODE ......................................................................................15
AVI FILES.............................................................................................28
RECORD FRAMERATE ..........................................................................15
Warranty Notice.................................................................................................30
VIDEO QUALITY ....................................................................................16
RECORD SCHEDULE .............................................................................16
SUB MENU...............................................................................................17
PASSWORD CHANGE ........................................................................17
1
2
• Full-screen resolution:
Display: 720 x 480 (NTSC), 720 x 576 (PAL)
Recording: 640 x 224 (NTSC), 640 x 272 (PAL)
Introduction
EB1004 BAK is a stand-alone, non-PC based DVR unit that provides real-time
monitoring and digital recording of surveillance video. Up to four video
cameras and four sensor devices can be hooked up to this DVR unit. It is also
equipped with an output relay that allows connection of an alarm device.
• Display and recording frame rate:
Quad mode: 30/25 fps (NTSC/PAL) per channel, total of 120/100 fps
(NTSC/PAL)
• Scheduled recording (00:00~23:00 selectable)
Surveillance, digital recording and playback are controlled through the front
panel buttons. Users can connect EB-1004 BAK to a PC to trace back video
files, and even save image as both BMP and AVI files. With the
on-screen-display (OSD) menu, you can customize video recording settings,
sensor and alarm settings, password protection, hard drive recycling, and more.
• Search for recorded videos by date/time/event
Surveillance video is recorded in high-quality Motion-JPEG format. Two
recording modes are available. EACH mode records video from each video
camera in 640 x 224 resolution at 7.5 fps. QUAD mode records video in 320 x
112 resolution and up to 30 fps/25 fps (NTSC/PAL).
• 1 USB 2.0 Port
• Input/Output: 4 sensor inputs and 1 relay output control
• Motion detection recording.
• Removable HDD bay
• Application driver CD (for Windows 2000/XP)
Front Panel
3
2
15
5
4
1
6
12
7
11
20
EB1004 BAK provides a removable rack for installing one hard drive and an internal slot for
installing a second hard drive.
16
19
17
8
Features and Specifications
9
10
12
13
14
• Non-PC stand-alone security digital video recorder
• 4 composite video inputs and 1 composite output
• VGA output for LCD monitor display
• Front panel buttons and OSD control
• Motion-JPEG video compression
1
REC : Start video recording.
2
MENU : Open/Close the OSD main menu or subsequent submenus.
3
: Go up one item.
: Go down one item.
4
• Factory defaulted to NTSC or PAL
5
• Supports 2 hard drives (not included)
3
SELECT :
(a) Cycle through various options in a selected menu item.
(b) Open a submenu
4
18
6
:
(a) Display Channel 1 in full-screen.
(b) When in the OSD menu, pressing button is equivalent to entering the number "1".
7
:
(a) Display Channel 2 in full-screen.
(b) Pressing this button is equivalent to entering the number "2" when in the OSD
menu.
8
:
(a) Display Channel 3 in full-screen.
(b) Pressing this button is equivalent to entering the number "3" when in the OSD
menu.
9
:
(a) Display Channel 4 in full-screen.
(b) Pressing this button is equivalent to entering the number "4" when in the OSD
menu.
10
:
Display cameras in quad screen.
11 X :
(a) Display the Playlist.
12
(b) Play back a recording.
/ „ :
(a) Pause playback.
(b) Pause/Stop recording.
: Fast reverse during playback.
14 :
Back Panel
1
2
3
4
6
5
1
VIDEO OUT (BNC) : Composite video output for connection to a television monitor.
2
VGA OUT (15-pin D-Sub) : VGA output for connection to a VGA monitor.
3
CH1 ~ CH4 (BNC) : Composite video input for connection of up to four video
cameras. (Video input : V = 1 Vp-p)
4
Sensor Inputs and Relay Output : For connection of up to 4 sensor devices and an
alarm device. (Relay : 1A @ 125V AC/30V DC)
5
Power Socket : For connecting the power adapter. (12V @ 4.2A)
6
Ω Hook: Fix the power adapter after it is plugged into Power Socket.
Setting Up the DVR Unit
13
(a) Fast forward during playback.
(b) Toggle between the Playlist and the date/time search controls.
15 Removable hard disk rack with lock
CAUTION
BEFORE REMOVING THE REMOVABLE OR INTERNAL HARD DISK,
POWER OFF THE DVR UNIT FIRST.
Installing Hard Drives
Before you install hard drives, please adjust the jumpers’ setting according to
users’ demands. Please refer to your hard disk label to adjust jumpers’ settings.
The DVR unit allows you to install up
to two hard drives (a master and slave
drive).
Install the master hard drive inside
DVR unit and fix it, and put the slave
hard drive in a removable hard disk
bay as the right picture shows.
16 Removable Power LED
17 Removable Hard disk LED
18 Hard disk LED
19 DVR Power LED
20 USB2.0 Socket
5
6
Install the Hard Drive in a Removable Case
1.
Remove the removable hard
drive drawer from the case.
2.
3.
Remove the upper cover of the
drawer.
Connect the power connector
to the hard drive as the right
picture shows.
Install a Removable Hard Drive Case in a PC (Optional)
For users who purchase an optional hard drive case, please follow the steps to
install the case in a PC.
1.
Power off your PC and remove the cover of your PC.
2.
Remove a front cover and free a 5 1/4” drive bay. Insert the hard disk
holder. Mount the hard disk holder, screw up the holder, and connect the
IDE slot and power connector from PC’s motherboard.
3.
Remove the drawer of the removable hard disk case. Please refer to
Install the Hard Drive in a Removable Case to install the hard drive.
4.
Slide the drawer into the removable hard disk case, power on the PC and
check the LED indicators. If the LED indicators light up, it is ok to use
the hard drive in the removable case.
Connecting Devices
At the back panel of the DVR unit, you can connect up to four video cameras,
four sensor devices, and one alarm device. You can connect a VGA monitor or
a television monitor as a display device. Use a USB cable to connect to a PC if
it is necessary.
4.
Connect the hard disk
connector into the inner tray’s
slot.
5.
Close the upper cover. Slide
the drawer into the removable
hard drive case.
6.
Power on the unit to see the LED indicators on the triple frame holders.
If the LED indicators light up, you may use the hard disk.
Connecting cameras, sensors, alarm, and display device
Basic Devices
• Cameras
7
8
Connect the video output of each video camera or composite video source
to the CH1 ~ CH4 connectors.
• VGA monitor
Connect a VGA monitor to the VGA OUT connector of the DVR unit to
use as a display for video surveillance and playback.
• Power adapter
Plug the provided 110V AC or 220V power adapter into the DVR unit's
power socket.
Optional Devices
• Television monitor
Use a BNC-to-RCA adapter to connect a regular TV monitor to the DVR
unit's VIDEO OUT connector.
Operating the DVR Unit
First Time Use
Connecting the DVR unit to a power outlet automatically turns on its power.
When the DVR unit is newly installed or replaced with hard drive(s), the hard
drive(s) will automatically be formatted.
HDD Checking...
Master
80072MB
HDD formatting
HDD Checking...
Master
80072MB
New HDD format completed
Slave
No HDD Detected
• Sensors and alarm device
Surveillance Screen
Surveillance video can be viewed and recorded in two screen modes: EACH
mode and QUAD mode.
Connect up to four sensor devices to the terminals that are numbered 1 to
8 at the back panel. Each pair of terminals is for the ground (-) and
positive (+) input voltage. For instance:
Terminal 1 : Connect to the ground (-) wire of Sensor 1
Terminal 2 : Connect to the positive (+) wire of Sensor 1
....
....
Terminal 7 : Connect to the ground (-) wire of Sensor 4
Terminal 8 : Connect to the positive (+) wire of Sensor 4
Under the EACH mode, video from the video cameras is recorded in
full-screen resolution, but each video takes turns in being recorded (from one
camera to the next). Each of the surveillance videos is recorded only at a
maximum frame rate of 7.5fps. When viewing live video using EACH mode,
you can switch between full screen and quad screen.
Whereas in QUAD mode, video from the video cameras is recorded at a lower
resolution, yet each video is recorded in full frame rate, full motion. Videos
recorded in QUAD mode can only be played back in QUAD mode.
Connect an alarm device to the terminals that are numbered 9 and 10:
Terminal 9 : Connect to the positive (+) wire of the alarm device
Terminal 10 : Connect to the ground (-) wire of the alarm device
• Desktop/Laptop computer
Connect EB 1004 BAK to a PC with a USB cable. Insert the USB
connector to PC’s USB socket.
9
EACH mode
QUAD mode
10
Use the following front panel buttons to select the desired video camera to
display in full screen:
CH1: Camera 1
CH2: Camera 2
CH3: Camera 3
CH4: Camera 4
Note: The recording mode can be selected in the OSD main menu.
2
Video Recording and Playback
If you want to switch to the other hard drive or search for a range of
video recordings, press . The ">" arrowhead cursor will then move up
to the top of the screen.
To record surveillance video:
1
2
To customize recording settings, press the MENU button and choose the
desired recording settings. Refer to the section, "Setup Menu" for details.
Press the REC button. During recording, the screen shows the following:
Press the SELECT button to switch between the MASTER and SLAVE
drives.
4 Press to move down to the recording date and time entries.
5 Press or to move through each item in the recording date and time
entries. While on an item such as the month, press the SELECT button
repeatedly to cycle through the numbers, and stop pressing the button
when you have reached the desired number.
6 Press to move the cursor back to the Playlist,
7 Press or to move up or down in the Playlist.
8 When you have selected the desired video recording, press X to play
back.
9 To fast forward through the video, press . To fast reverse, press .
10 Press to pause playback, or press „ to stop playback.
3
3
To stop the recording, press „.
To play back the recorded video:
1
Press X to display the Playlist:
11
12
MAIN MENU
Setup Menu
1
Press the MENU button to display the OSD main menu.
MAIN MENU
MAIN MENU
> CAMERA SELECT
RECORD SELECT
RECORD MODE
RECORD FRAMERATE
VIDEO QUALITY
RECORD SCHEDULE
SUBMENU
HARD DRIVE SETUP
SENSOR SETUP
1234
1234
EACH
30
NORMAL
RECORD SCHEDULE
> CAMERA SELECT
RECORD SELECT
RECORD MODE
RECORD FRAMERATE
VIDEO QUALITY
RECORD SCHEDULE
SUBMENU
HARD DRIVE SETUP
SENSOR SETUP
v
+TTTSSSSSTTTTMMMMTTTTT+
|
|
|
|
|
|
|
|
|
0
3
6
9
12 15 18 21 24
PRESS (< , >), THEN(SELECT)
PRESS (MENU) TO EXIT
PRESS (< , >), THEN(SELECT)
PRESS (MENU) TO EXIT
PRESS (< , >), THEN(SELECT)
PRESS (MENU) TO EXIT
SUB MENU
> PASSWORD CHANGE
TIME SET
VGA SETUP
MOTION SETUP
2
PRESS (< , >), THEN(SELECT)
PRESS (MENU) TO EXIT
3
TIME
CURRENT PASSWORD :
NEW
PASSWORD
CONFIRM PASWORD
VGA SETUP
2004/01/10 15:30:25
^
> RESOLUTION
1024 ^ 768
REFRESH RATE
60HZ
:
:
PRESS (<, >),THEN(SELECT)
PRESS (MENU) TO EXIT
1234
1234
EACH
30
NORMAL
PRESS (< , >), THEN(SELECT)
PRESS (MENU) TO EXIT
MOTION SETUP
MOTION CAMERA
____
MOTION SENSITIVITY
05
MOTION RECORD TIME
05
PRESS (< , >), THEN(SELECT)
PRESS (MENU) TO EXIT
4
5
6
Press or to move up or down through the items in the menu. The
">" arrowhead cursor moves as you press these buttons.
The first five items in the menu provide selectable settings. Press the
SELECT button to repeatedly cycle through the available settings. Stop
pressing the button when you have chosen the desired setting.
The last four items in the menu are second-level menus. Press the
SELECT button to display the corresponding menu.
When you are in a second-level menu, press the MENU button to return
to the main menu.
To close the main menu and return to the surveillance screen, press the
MENU button again.
HARD DRIVE SETUP
> OVERWRITE ENABLED
YES
MASTER HDD SIZE
80072MB
MASTER HDD USED
16014MB 20%
MASTER HDD FORMAT
SLAVE HDD SIZE
N/A
SLAVE HDD USED
N/A
SLAVE HDD FORMAT
PRESS (< , >), THEN(SELECT)
PRESS (MENU) TO EXIT
CAMERA SELECT
This determines which of the cameras will be displayed on the surveillance
screen. Use the following front panel buttons to individually switch on or off
each of the camera displays:
SENSOR SETUP
> SENSOR RECORD TIME
ALARM OUT TIME
CHANNEL1
CHANNEL2
CHANNEL3
CHANNEL4
15
05
NORMAL-CLOSE
NORMAL-OPEN
NOT INSTALLED
NOT INSTALLED
PRESS (< , >), THEN(SELECT)
PRESS (MENU) TO EXIT
13
CH1: Camera 1
CH2: Camera 2
CH3: Camera 3
CH4: Camera 4
You can also press the SELECT button to cycle through different camera
display combinations. For instance:
14
VIDEO QUALITY
There are three video quality settings to choose from: BEST, GOOD or
NORMAL.
(1 2 3 4) : Switch on all camera displays.
(1 - - 4) : Switch on camera display 1 and 4 only.
(- 2 3 -) : Switch on camera display 2 and 3 only.
(- - - -) : Disable all camera displays.
RECORD SELECT
This determines which of the cameras surveillance video will be recorded from.
The way to select cameras is the same as CAMERA SELECT.
Note: Only the enabled camera displays in the CAMERA SELECT item can be
selected for recording.
Choosing NORMAL allows you to save more on hard drive space, but the
quality of recorded video images is moderate.
Recording hours on 40GB hard drive:
Video Signal
Display Format Video Quality
BEST
QUAD mode
NTSC
RECORD MODE
There are two recording modes to choose from: EACH and QUAD.
When you choose the EACH recording mode, you can view each camera
display in full-screen during the recording process by using the following front
panel buttons:
EACH mode
QUAD mode
PAL
EACH mode
CH1: Camera 1
CH2: Camera 2
CH3: Camera 3
CH4: Camera 4
Likewise, when you finish recording, you can also play back the recorded video
in full-screen by using the above buttons.
While viewing or recording video in full screen, press
to switch the
30 fps
15 fps
7 fps
1 fps
18 hrs
36 hrs
72 hrs
540 hrs
720 hrs
GOOD
24 hrs
48 hrs
96 hrs
NORMAL
BEST
GOOD
NORMAL
BEST
GOOD
NORMAL
BEST
GOOD
NORMAL
29 hrs
32 hrs
45 hrs
56 hrs
19 hrs
24 hrs
30 hrs
31 hrs
45 hrs
59 hrs
58 hrs
64 hrs
90 hrs
112 hrs
38 hrs
48 hrs
60 hrs
62 hrs
90 hrs
118 hrs
116 hrs 870 hrs
128 hrs 960 hrs
180 hrs 1350 hrs
224 hrs 1680 hrs
76 hrs 475 hrs
96 hrs 600 hrs
120 hrs 750 hrs
124 hrs 775 hrs
180 hrs 1125 hrs
236 hrs 1475 hrs
RECORD SCHEDULE
By default, the DVR unit is customized for continuous 24-hour video recording.
If you prefer to record video only at certain time schedules within a day, you
can choose specific recording hours. If the DVR unit is connected to sensor
devices, you can also customize the unit to initiate video recording only when
the sensors detect an event.
display back to quad screen.
Note: Refer to the section "Surveillance Screen" on page 10 for details on the
differences between EACH and QUAD modes.
RECORD FRAME RATE
This sets the number of images per second of video that is recorded.
RECORD SCHEDULE
v
+TTTTTTTTTTTTTTTTTTTTTTT+
|
|
|
|
|
|
|
|
|
0
3
6
9
12 15 18 21 24
PRESS (< , >), THEN(SELECT)
PRESS (MENU) TO EXIT
By default, frame rate is set at 30 fps for NTSC, 25 fps for PAL. There are 10
different frame rates you can choose from.
15
16
The factory default password is "111111". Use the following front panel
buttons to input a numeric password:
To customize the recording schedule:
Each number in the PROGRAMMED RECORD menu represents the
time schedule (in hours) for recording, and the "v" cursor indicates the
time that is selected. Press or to move through the time schedules.
Press the SELECT button repeatedly to cycle through these settings:
( T ) For automatic non-stop video recording
( S ) For sensor recording. The DVR unit initiates recording only when
the attached sensor devices detect motion from the video cameras.
( M ) For motion recording. The DVR unit initiates recording only when
motion is detected from video cameras.
( - ) Disables recording at that time schedule.
1
2
SUB MENU
The SUB MENU allows you to change the password, system date and time,
and VGA display settings.
For "1"
2
TIME
PRESS (< , >), THEN(SELECT)
PRESS (MENU) TO EXIT
To change the system date and time:
1
PASSWORD CHANGE
To change the password:
2
Input the prompted information:
CURRENT PASSWORD :
------
NEW
:
------
:
------
17
The "Password changed" message is then displayed. This message
flashes three times, then you will be returned to the SUB MENU.
2004/01/10 15:30:25
^
PRESS (< , >), THEN(SELECT)
PRESS (MENU) TO EXIT
CONFIRM PASWORD
For "4"
TIME SET
> PASSWORD CHANGE
TIME SET
VGA SETUP
MOTION SETUP
PASSWORD
For "3"
Note: You will be prompted to enter the password when you attempt to
format the hard drive(s) in the HARD DRIVE SETUP menu.
SUB MENU
1
For "2"
Press or to move through the "year/month/day" and
"hour:minute:second" entries. The "^" cursor indicates the entry that is
selected.
Per selected entry, press the SELECT button repeatedly to cycle
through the numbers. Stop pressing the button when you reach the
desired number.
18
VGA SETUP
. You will see the screen
To setup all camera, press
shows MOTION CAMERA 1 2 3 4. Press the same button again to cancel
the setting.
VGA SETUP
> RESOLUTION
REFRESH RATE
1024 ^ 768
60HZ
To setup channel 1 and 4 only, press
. You will see the screen
shows MOTION CAMERA 1
4.Press the same buttons again to
cancel the setting.
PRESS (< , >), THEN(SELECT)
PRESS (MENU) TO EXIT
Set RESOLUTION and REFRESH RATE based on the supported display
mode and refresh rate of the VGA monitor that is connected to the DVR unit.
Different monitors support different refresh rates:
Resolution
640 x 480
800 x 600
1024 x 768
1280 x 1024
Refresh Rate Frequency (Hz)
60, 72, 75, 85
60, 72, 75, 85
60, 70, 75, 85
60
To setup channel 2 and 3 only, press
. You will see the screen
shows MOTION CAMERA 2 3 . Press the same buttons again to
cancel the setting.
To adjust MOTION SENSIVITY,
1.
Press or to move the arrowhead cursor to MOTION
SENSITIVITY in the menu.
2.
Press the SELECT button repeatedly to cycle through the numbers. The
sensitivity level ranges from 1 to 10. Level 1 is the least sensitive one and
Note: The best refresh rate for LCD monitor is 60Hz.
Level 10 is the most sensitive one.
MOTION SETUP
To setup the Motion Time,
1.
MOTION SETUP
>MOTION CAMERA
MOTION SENSITIVITY
MOTION RECORD TIME
____
01
05
PRESS (< , >), THEN(SELECT)
PRESS (MENU) TO EXIT
Press or to move the arrowhead cursor to MOTION TIME in the
menu.
2.
Press the SELECT button repeatedly to cycle through the numbers. The
time setting ranges from 5 to 30 seconds. Stop pressing the button when
reach the desired numbers.
To change MOTION CAMERA,
1.
Press or to move the arrowhead cursor to MOTION CAMERA in
the menu.
2.
Press the channel buttons to select cameras that you want to setup.
19
20
HARD DRIVE SETUP
SENSOR SETUP
HARD DRIVE SETUP
SENSOR SETUP
> OVERWRITE ENABLED
YES
MASTER HDD SIZE
80072MB
MASTER HDD USED
16014MB 20%
MASTER HDD FORMAT
SLAVE HDD SIZE
N/A
SLAVE HDD USED
N/A
SLAVE HDD FORMAT
> SENSOR RECORD TIME
ALARM OUT TIME
CHANNEL 1
CHANNEL 2
CHANNEL 3
CHANNEL 4
PRESS (< , >), THEN(SELECT)
PRESS (MENU) TO EXIT
15
05
NORMAL-CLOSE
NORMAL-OPEN
NOT INSTALLED
NOT INSTALLED
PRESS (< , >), THEN(SELECT)
PRESS (MENU) TO EXIT
OVERWRITE ENABLED
SENSOR RECORD TIME
This allows old video recordings on the hard drive(s) to be automatically
overwritten with new recordings when hard drive space is full.
This determines the duration of sensor recording (in minutes) in the event
that the sensor devices detect an event. There are seven selections to choose
from.
Press the SELECT button to enable or disable this feature (i.e., choose YES
or NO).
MASTER HDD SIZE and MASTER HDD USED
These items show the MASTER hard drive capacity and the amount of disk
space that has been used up by the video recordings.
MASTER HDD FORMAT
Press the SELECT button on this menu item to reformat the MASTER hard
drive. You will then be prompted to enter the password. If an invalid
password is entered, you will not be allowed to format the hard drive.
Note: All recordings on the MASTER hard drive will be deleted when you
reformat the hard drive.
SLAVE HDD SIZE and SLAVE HDD USED
These items show the SLAVE hard drive capacity and the amount of disk
space that has been used up by the video recordings.
SLAVE HDD FORMAT
ALARM OUT TIME
This determines the duration of sound (in minutes) that is set off when the
alarm device is triggered.
CHANNEL1 ~ CHANNEL4
These correspond to the four sets of sensor inputs on the DVR unit.
Customize these according to the initial state of the attached sensor devices.
There are three states to choose from:
NOT INSTALLED : Indicates that the channel does not have a sensor
device connected.
NORMAL-OPEN : Indicates that the initial state of the sensor device is
Normal-Open. When the sensor device detects an event and its state changes
to Normal-Close, video recording is initiated.
NORMAL-CLOSE : Indicates that the initial state of the sensor device is
Normal-Close. When the sensor device detects an event and its state changes
to Normal-Open, video recording is initiated.
Press the SELECT button on this menu item to reformat the SLAVE hard
drive. You will then be prompted to enter the password. If an invalid
password is entered, you will not be allowed to format the hard drive.
Note: All recordings on the SLAVE hard drive will be deleted when you
reformat the hard drive.
21
22
Connect to a PC
3.
Select a language. Click
Next to continue the
installation.
4.
Please click Browser.. to
change the directory if it
is necessary. Click Next
to continue the
installation.
EB1004 BAK provides a convenient tool to trace back the recorded
surveillance video, catch specific images and save as AVI files. With the
EB-DVR Playback Application, users can play back the surveillance video,
catch images and backup all recorded images easily .
First Time Use
Connecting DVR unit to a power outlet automatically turns on its power. Plug a
USB connector into the USB socket of a PC when the PC is off. Follow the
instructions to install the driver:
1.
Insert the CD driver into
CR-ROM’s plate. It will
auto-run. You will see the
screen on the right side.
Note: The application
supports Windows
2000/XP only.
2.
Note: You can see the
DVR-Playback Application
version on the top of this
screen when you install this
application.
5.
Click Finish to complete
the installation.
Click Next. Follow the
steps to finish the
installation.
23
24
Operating EB-DVR Playback Application
Click
to run the application. Select the Hard Disk and click OK.
5.
Backward play: Play the video backward.
6.
Play one frame: Display a forward static frame.
7.
Back one frame: Display a backward static frame.
8.
Pause: Pause the playback.
9.
Forward Search: Fast play the recorded video to search an
appointed image.
Note: The DVR’s HDD number will be next to your PC’s HDD
number. If there is only one hard disk in PC, PC’s hard disk will be
HDD1 and DVR’s hard disk will be HDD2 and so on. DVR’s HDD
will not be shown under PC’s Operating System.
You will see EB-DVR screen as followed.
10.
Stop: Stop the playback
11.
Snapshot: Save the present screen as a BMP file.
12.
Print: Print the current display.
13.
AVI file: Record an appointed video and save it as an AVI file.
14.
Version Identification: Press Ctrl + Alt + V buttons to see the
product version if you need this when you contact with customer
service.
For users with only one hard disk in EB-DVR unit, there are 2 ways to read
the data in the hard drive. One way is to install the hard disk inside the
EB-DVR unit and utilize a USB cable to connect both EB-DVR unit and PC.
In this situation, please read the data in the master hard drive by EB-DVR
application. The other way is to install the master hard disk in the removable
hard disk case, insert the removable hard disk drawer into PC and then read
the data by EB-DVR application.
For users with 2 hard disks in EB-DVR unit, users can connect EB-DVR
unit to PC with a USB cable to read the master hard disk inside the machine.
To read the salve drive inside the removable hard disk drawer, please insert
the drawer to PC and use to EB-DVR application to read the data.
Channel Selection
1.
Channel 1- Channel 4: Switch between cameras.
2.
Change Driver: Switch between different hard disks.
3.
Event List: Display all the recorded events stored in hard disks.
4.
Play: Play the recorded video.
25
This determines which of the cameras will be displayed on the surveillance
screen.
Choose an appointed channel to display the surveillance screen by clicking
the channel icon. Click once to show a full-screen display. To show a quad
screen, click the same icon again.
26
Free Video Playback
After selecting the appointed hard drive, click
to select an event and
click OK to play back the appointed surveillance.
When you click the Event List icon, it pops-up an event table as the
following illustration shows. You will see the table shows Record mode,
Start time and End time of each event. Record Mode can be “T”, “M” or
“S”. “T” represents Total Recording, which means the camera keeps on
recording continually. “M” means Motion Recording, which means the
recording starts once the camera detects motion. “S” represents Sensor
Recording, which means the camera records when the sensor detects an
event.
Event List enables you to playback any recorded event anytime.
Record Model
There are four fast play modes:X0, X2, X4 and X8.
“2004-02-04 17:59:56 X8” means the record is played at X8.
Click
click
Click
Click
Start Time
End Time
to see a forward static play. To see a backward static display,
.
to pause the playing.
to stop the video.
Catch Images and Video
WB-DVR Playback Application provides functions to output both
dynamic and static images. Users can easily catch a static screen and save
it as a BMP file, or save some fragment of recorded video as an AVI file.
When you decide which event to play, click
to display the video or
click
to display a recorded dynamic event reversely. Click
to
search the appointed video. Users can select the forward search mode fast
play at 2x, 4x or 8x speed. Click once to fast play the video at 2x. Click
twice to fast play the video at 4x. Click 3 times to fast play the video at 8x.
Click the same button to cycle through different fast play modes. The
following picture shows the video is played at 8X.
Snapshot
Click
to save the desired screen as a BMP file. Users can keep a
full-screen snapshot or a quad screen snapshot. This function allows to
preserve static images.
Print
Click
to print the screen. Users can switch to a specific channel and
print out the image during the surveillance. Printing is allowed in a
display of full-screen mode or quad mode.
AVI Files
27
28
Users can backup or catch the data in DVR unit’s hard disks by saving
the recorded video as AVI files and play the files by Windows Media
Player.
Click
to save an appointed surveillance video. After clicking the icon,
a window shows to request the file name and directory. Click Save to
start the recording. Click
again to finish the recording. EB-1004 BAK
allows user to backup data in its master hard disk through a USB cable.
To backup the data in DVR unit’s slave hard disk, please insert the
removable hard disk bay to your PC and save the files as AVI files.
Warranty Notice
LIMITED WARRANTY
AVerMedia TECHNOLOGIES, Inc. warrants this product to be free of defects resulting from faulty
manufacture or components under the following terms:
WARRANTY LENGTH
Labor is warranted for (1) one year from the date of purchase.
Parts are warranted for (1) one year from the date of purchase.
Replacement products will be warranted for the remainder of the one year warranty period or (30) thirty
days, whichever is longer.
WHO IS PROTECTED
This warranty is enforceable only by the first consumer purchaser.
WHAT IS AND IS NOT COVERED
Except as specified below, this warranty covers all defects resulting from faulty manufacturing of this
product. The following are not covered by the warranty.
1. Any product on which the serial number has been defaced, modified, or removed.
2. Damage, deterioration, or malfunction resulting from :
A. Accident, abuse, misuse, neglect, fire, water, lightning, or other acts of nature,
commercial or industrial use, unauthorized product modification, or failure to follow
instructions included with the product.
B. Misapplication of service by someone other than the manufacturer’s representative.
C. Any shipment damages. (Claims must be made with carrier.)
D. Any other cause which does not relate to a product defect.
3. Cartons, cases, batteries, cabinets, tapes, or accessories used with product.
4. AVerMedia does not warrant that this product will meet your requirements; it is your
responsibility to determine the suitability of this product for your purpose.
WHAT WE WILL AND WILL NOT PAY FOR
We will pay labor and material expenses for covered items. However, we will not pay for the following :
1. Removal or installation charges.
2. Shipping charges.
3. Any incidental charges.
EXCLUSION OF DAMAGES
THE MANUFACTURER’S SOLE OBLIGATION AND LIABILITY UNDER THIS WARRANTY IS LIMITED
TO THE REPAIR OR REPLACEMENT OF A DEFECTIVE PRODUCT AT OUR OPTION. THE
MANUFACTURER SHALL NOT, IN ANY EVENT, BE LIABLE TO THE PURCHASER OR ANY THIRD
PARTY FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGE (INCLUDING, BUT NOT LIMITED
TO, DAMAGES RESULTING FROM INTERRUPTION OF SERVICE AND LOSS OF BUSINESS) OR
LIABILITY IN TORT RELATING TO THIS PRODUCT OR RESULTING FROM ITS USE OR
POSSESSION.
LIMITATIONS OF IMPLIED WARRANTIES
There are no other oral or written warranties, expressed or implied, including but not limited to those of
merchantability or fitness for a particular purpose. Any implied warranties are limited in duration to one
year from the date of purchase.
STATE LAW AND YOUR WARRANTY
This warranty gives you specific legal rights, and you may also have other rights granted under state law.
These rights vary from state to state.
CONTACT INFORMATION
http://www.avermedia.com
29
30